All of lore.kernel.org
 help / color / mirror / Atom feed
From: Kalle Valo <kvalo@codeaurora.org>
To: ath11k@lists.infradead.org
Cc: linux-wireless@vger.kernel.org
Subject: [PATCH 3/5] ath11k: mac: remove unused conf_mutex to solve a deadlock
Date: Wed, 30 Sep 2020 13:51:11 +0300	[thread overview]
Message-ID: <1601463073-12106-4-git-send-email-kvalo@codeaurora.org> (raw)
In-Reply-To: <1601463073-12106-1-git-send-email-kvalo@codeaurora.org>

From: Wen Gong <wgong@codeaurora.org>

The conf_mutex is not use and lead below deadlock, remove it to solve
the deadlock issue.

[   44.967496] NET: Registered protocol family 42
[   45.119629] ath11k_pci 0000:06:00.0: WARNING: ath11k PCI support is experimental!
[   45.120087] ath11k_pci 0000:06:00.0: BAR 0: assigned [mem 0xdc000000-0xdc0fffff 64bit]
[   45.120108] ath11k_pci 0000:06:00.0: enabling device (0000 -> 0002)
[   45.206525] ath11k_pci 0000:06:00.0: aspm 0x42 changed to 0x40
[   45.207430] mhi 0000:06:00.0: Requested to power ON
[   45.208609] mhi 0000:06:00.0: Power on setup success
[   46.190711] ath11k_pci 0000:06:00.0: chip_id 0x0 chip_family 0xb board_id 0x101 soc_id 0xffffffff
[   46.190729] ath11k_pci 0000:06:00.0: fw_version 0x306a70f fw_build_timestamp 2000-01-01 00:00 fw_build_id
1]: Starting Load/Save RF Kill Switch Status...
[   46.385118] ath11k_pci 0000:06:00.0 wlp6s0: renamed from wlan0
1]: Started Load/Save RF Kill Switch Status.
[   53.566669] wlp6s0: authenticate with 00:03:7f:48:dd:bf
[   53.809092] wlp6s0: send auth to 00:03:7f:48:dd:bf (try 1/3)
[   53.816490] wlp6s0: authenticated
[   53.818618] wlp6s0: associate with 00:03:7f:48:dd:bf (try 1/3)
[   53.820839] wlp6s0: RX AssocResp from 00:03:7f:48:dd:bf (capab=0x1 status=0 aid=2)
[   53.834859]
[   53.834861] ======================================================
[   53.834862] WARNING: possible circular locking dependency detected
[   53.834863] 5.9.0-rc5-wt-ath+ #198 Not tainted
[   53.834864] ------------------------------------------------------
[   53.834865] kworker/u16:3/166 is trying to acquire lock:
[   53.834866] ffff8c4b37184f78 (&ar->conf_mutex){+.+.}-{3:3}, at: ath11k_mac_op_config+0x16/0x30 [ath11k]
[   53.834875]
[   53.834875] but task is already holding lock:
[   53.834876] ffff8c4b37182808 (&local->iflist_mtx){+.+.}-{3:3}, at: ieee80211_set_associated+0x167/0x360
[   53.834879]
[   53.834879] which lock already depends on the new lock.
[   53.834879]
[   53.834880]
[   53.834880] the existing dependency chain (in reverse order) is:
[   53.834881]
[   53.834881] -> #1 (&local->iflist_mtx){+.+.}-{3:3}:
[   53.834884]        __lock_acquire+0x3bf/0x6e0
[   53.834886]        lock_acquire+0xb6/0x270
[   53.834887]        __mutex_lock+0x88/0x8e0
[   53.834890]        ieee80211_set_hw_80211_encap+0x3e/0x1f0
[   53.834895]        ath11k_mac_op_add_interface+0x348/0x7f0 [ath11k]
[   53.834897]        drv_add_interface+0x7c/0x190
[   53.834899]        ieee80211_do_open+0x552/0x9a0
[   53.834901]        __dev_open+0xe5/0x190
[   53.834902]        __dev_change_flags+0x1c6/0x230
[   53.834903]        dev_change_flags+0x1c/0x50
[   53.834905]        do_setlink+0x246/0xc60
[   53.834906]        __rtnl_newlink+0x607/0x990
[   53.834907]        rtnl_newlink+0x3f/0x60
[   53.834908]        rtnetlink_rcv_msg+0x174/0x490
[   53.834910]        netlink_rcv_skb+0x42/0x100
[   53.834911]        netlink_unicast+0x18c/0x250
[   53.834912]        netlink_sendmsg+0x227/0x460
[   53.834914]        sock_sendmsg+0x59/0x60
[   53.834915]        ____sys_sendmsg+0x1f5/0x230
[   53.834916]        ___sys_sendmsg+0x70/0xb0
[   53.834917]        __sys_sendmsg+0x54/0xa0
[   53.834919]        do_syscall_64+0x33/0x40
[   53.834920]        entry_SYSCALL_64_after_hwframe+0x44/0xa9
[   53.834921]
[   53.834921] -> #0 (&ar->conf_mutex){+.+.}-{3:3}:
[   53.834923]        check_prev_add+0x98/0x9f0
[   53.834925]        validate_chain+0x404/0x6c0
[   53.834926]        __lock_acquire+0x3bf/0x6e0
[   53.834927]        lock_acquire+0xb6/0x270
[   53.834929]        __mutex_lock+0x88/0x8e0
[   53.834934]        ath11k_mac_op_config+0x16/0x30 [ath11k]
[   53.834935]        ieee80211_hw_config+0xb3/0x270
[   53.834937]        ieee80211_set_associated+0x17c/0x360
[   53.834938]        ieee80211_assoc_success.constprop.0+0x5a2/0xc80
[   53.834940]        ieee80211_rx_mgmt_assoc_resp+0x16a/0x350
[   53.834941]        ieee80211_sta_rx_queued_mgmt+0xca/0x410
[   53.834943]        ieee80211_iface_work+0x1f3/0x350
[   53.834945]        process_one_work+0x265/0x5d0
[   53.834946]        worker_thread+0x49/0x300
[   53.834948]        kthread+0x135/0x150
[   53.834949]        ret_from_fork+0x22/0x30
[   53.834950]
[   53.834950] other info that might help us debug this:
[   53.834950]
[   53.834951]  Possible unsafe locking scenario:
[   53.834951]
[   53.834952]        CPU0                    CPU1
[   53.834952]        ----                    ----
[   53.834953]   lock(&local->iflist_mtx);
[   53.834954]                                lock(&ar->conf_mutex);
[   53.834955]                                lock(&local->iflist_mtx);
[   53.834956]   lock(&ar->conf_mutex);
[   53.834957]
[   53.834957]  *** DEADLOCK ***
[   53.834957]
[   53.834958] 4 locks held by kworker/u16:3/166:
[   53.834959]  #0: ffff8c4b37c22948 ((wq_completion)phy0){+.+.}-{0:0}, at: process_one_work+0x1d3/0x5d0
[   53.834961]  #1: ffffa98300abfe70 ((work_completion)(&sdata->work)){+.+.}-{0:0}, at: process_one_work+0x1d3/0x5d0
[   53.834963]  #2: ffff8c4b371e4cd0 (&wdev->mtx){+.+.}-{3:3}, at: ieee80211_sta_rx_queued_mgmt+0x4b/0x410
[   53.834965]  #3: ffff8c4b37182808 (&local->iflist_mtx){+.+.}-{3:3}, at: ieee80211_set_associated+0x167/0x360
[   53.834968]
[   53.834968] stack backtrace:
[   53.834969] CPU: 1 PID: 166 Comm: kworker/u16:3 Not tainted 5.9.0-rc5-wt-ath+ #198
[   53.834970] Hardware name: Intel(R) Client Systems NUC8i7HVK/NUC8i7HVB, BIOS HNKBLi70.86A.0049.2018.0801.1601 08/01/2018
[   53.834972] Workqueue: phy0 ieee80211_iface_work
[   53.834974] Call Trace:
[   53.834976]  dump_stack+0x77/0xa0
[   53.834978]  check_noncircular+0x15d/0x180
[   53.834980]  check_prev_add+0x98/0x9f0
[   53.834982]  ? add_chain_cache+0x143/0x440
[   53.834984]  validate_chain+0x404/0x6c0
[   53.834986]  __lock_acquire+0x3bf/0x6e0
[   53.834988]  lock_acquire+0xb6/0x270
[   53.834993]  ? ath11k_mac_op_config+0x16/0x30 [ath11k]
[   53.834999]  ? ath11k_mac_op_config+0x16/0x30 [ath11k]
[   53.835001]  __mutex_lock+0x88/0x8e0
[   53.835006]  ? ath11k_mac_op_config+0x16/0x30 [ath11k]
[   53.835007]  ? sched_clock_cpu+0xc/0xb0
[   53.835009]  ? __lock_release+0x179/0x2c0
[   53.835014]  ath11k_mac_op_config+0x16/0x30 [ath11k]
[   53.835016]  ieee80211_hw_config+0xb3/0x270
[   53.835018]  ieee80211_set_associated+0x17c/0x360
[   53.835019]  ieee80211_assoc_success.constprop.0+0x5a2/0xc80
[   53.835021]  ? lockdep_hardirqs_on_prepare.part.0+0x9f/0x140
[   53.835023]  ? cmpxchg_double_slab.constprop.0+0x185/0x1a0
[   53.835025]  ? trace_hardirqs_on+0x1c/0x100
[   53.835027]  ? __slab_free+0x8f/0x330
[   53.835029]  ? slab_free_freelist_hook+0xf8/0x150
[   53.835031]  ? ieee802_11_parse_elems_crc+0x147/0x1d0
[   53.835032]  ? kfree+0x2b0/0x2d0
[   53.835034]  ? ieee802_11_parse_elems_crc+0x147/0x1d0
[   53.835036]  ieee80211_rx_mgmt_assoc_resp+0x16a/0x350
[   53.835041]  ieee80211_sta_rx_queued_mgmt+0xca/0x410
[   53.835043]  ? __lock_acquire+0x3bf/0x6e0
[   53.835045]  ? lock_acquire+0xb6/0x270
[   53.835046]  ? skb_dequeue+0x13/0x70
[   53.835048]  ? find_held_lock+0x32/0x90
[   53.835049]  ? sched_clock_cpu+0xc/0xb0
[   53.835051]  ? mark_held_locks+0x50/0x80
[   53.835053]  ? lockdep_hardirqs_on_prepare.part.0+0x9f/0x140
[   53.835054]  ? _raw_spin_unlock_irqrestore+0x34/0x40
[   53.835056]  ? trace_hardirqs_on+0x1c/0x100
[   53.835058]  ieee80211_iface_work+0x1f3/0x350
[   53.835060]  process_one_work+0x265/0x5d0
[   53.835062]  worker_thread+0x49/0x300
[   53.835063]  ? process_one_work+0x5d0/0x5d0
[   53.835065]  kthread+0x135/0x150
[   53.835066]  ? kthread_create_worker_on_cpu+0x60/0x60
[   53.835068]  ret_from_fork+0x22/0x30
[   53.835075] wlp6s0: associated
[   53.835132] IPv6: ADDRCONF(NETDEV_CHANGE): wlp6s0: link becomes ready

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1

Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
---
 drivers/net/wireless/ath/ath11k/mac.c | 11 +----------
 1 file changed, 1 insertion(+), 10 deletions(-)

diff --git a/drivers/net/wireless/ath/ath11k/mac.c b/drivers/net/wireless/ath/ath11k/mac.c
index c43844ed6b61..76e218e53fe7 100644
--- a/drivers/net/wireless/ath/ath11k/mac.c
+++ b/drivers/net/wireless/ath/ath11k/mac.c
@@ -758,21 +758,12 @@ static int ath11k_monitor_vdev_up(struct ath11k *ar, int vdev_id)
 
 static int ath11k_mac_op_config(struct ieee80211_hw *hw, u32 changed)
 {
-	struct ath11k *ar = hw->priv;
-	int ret = 0;
-
 	/* mac80211 requires this op to be present and that's why
 	 * there's an empty function, this can be extended when
 	 * required.
 	 */
 
-	mutex_lock(&ar->conf_mutex);
-
-	/* TODO: Handle configuration changes as appropriate */
-
-	mutex_unlock(&ar->conf_mutex);
-
-	return ret;
+	return 0;
 }
 
 static int ath11k_mac_setup_bcn_tmpl(struct ath11k_vif *arvif)
-- 
2.7.4


-- 
ath11k mailing list
ath11k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath11k

WARNING: multiple messages have this Message-ID (diff)
From: Kalle Valo <kvalo@codeaurora.org>
To: ath11k@lists.infradead.org
Cc: linux-wireless@vger.kernel.org
Subject: [PATCH 3/5] ath11k: mac: remove unused conf_mutex to solve a deadlock
Date: Wed, 30 Sep 2020 13:51:11 +0300	[thread overview]
Message-ID: <1601463073-12106-4-git-send-email-kvalo@codeaurora.org> (raw)
In-Reply-To: <1601463073-12106-1-git-send-email-kvalo@codeaurora.org>

From: Wen Gong <wgong@codeaurora.org>

The conf_mutex is not use and lead below deadlock, remove it to solve
the deadlock issue.

[   44.967496] NET: Registered protocol family 42
[   45.119629] ath11k_pci 0000:06:00.0: WARNING: ath11k PCI support is experimental!
[   45.120087] ath11k_pci 0000:06:00.0: BAR 0: assigned [mem 0xdc000000-0xdc0fffff 64bit]
[   45.120108] ath11k_pci 0000:06:00.0: enabling device (0000 -> 0002)
[   45.206525] ath11k_pci 0000:06:00.0: aspm 0x42 changed to 0x40
[   45.207430] mhi 0000:06:00.0: Requested to power ON
[   45.208609] mhi 0000:06:00.0: Power on setup success
[   46.190711] ath11k_pci 0000:06:00.0: chip_id 0x0 chip_family 0xb board_id 0x101 soc_id 0xffffffff
[   46.190729] ath11k_pci 0000:06:00.0: fw_version 0x306a70f fw_build_timestamp 2000-01-01 00:00 fw_build_id
1]: Starting Load/Save RF Kill Switch Status...
[   46.385118] ath11k_pci 0000:06:00.0 wlp6s0: renamed from wlan0
1]: Started Load/Save RF Kill Switch Status.
[   53.566669] wlp6s0: authenticate with 00:03:7f:48:dd:bf
[   53.809092] wlp6s0: send auth to 00:03:7f:48:dd:bf (try 1/3)
[   53.816490] wlp6s0: authenticated
[   53.818618] wlp6s0: associate with 00:03:7f:48:dd:bf (try 1/3)
[   53.820839] wlp6s0: RX AssocResp from 00:03:7f:48:dd:bf (capab=0x1 status=0 aid=2)
[   53.834859]
[   53.834861] ======================================================
[   53.834862] WARNING: possible circular locking dependency detected
[   53.834863] 5.9.0-rc5-wt-ath+ #198 Not tainted
[   53.834864] ------------------------------------------------------
[   53.834865] kworker/u16:3/166 is trying to acquire lock:
[   53.834866] ffff8c4b37184f78 (&ar->conf_mutex){+.+.}-{3:3}, at: ath11k_mac_op_config+0x16/0x30 [ath11k]
[   53.834875]
[   53.834875] but task is already holding lock:
[   53.834876] ffff8c4b37182808 (&local->iflist_mtx){+.+.}-{3:3}, at: ieee80211_set_associated+0x167/0x360
[   53.834879]
[   53.834879] which lock already depends on the new lock.
[   53.834879]
[   53.834880]
[   53.834880] the existing dependency chain (in reverse order) is:
[   53.834881]
[   53.834881] -> #1 (&local->iflist_mtx){+.+.}-{3:3}:
[   53.834884]        __lock_acquire+0x3bf/0x6e0
[   53.834886]        lock_acquire+0xb6/0x270
[   53.834887]        __mutex_lock+0x88/0x8e0
[   53.834890]        ieee80211_set_hw_80211_encap+0x3e/0x1f0
[   53.834895]        ath11k_mac_op_add_interface+0x348/0x7f0 [ath11k]
[   53.834897]        drv_add_interface+0x7c/0x190
[   53.834899]        ieee80211_do_open+0x552/0x9a0
[   53.834901]        __dev_open+0xe5/0x190
[   53.834902]        __dev_change_flags+0x1c6/0x230
[   53.834903]        dev_change_flags+0x1c/0x50
[   53.834905]        do_setlink+0x246/0xc60
[   53.834906]        __rtnl_newlink+0x607/0x990
[   53.834907]        rtnl_newlink+0x3f/0x60
[   53.834908]        rtnetlink_rcv_msg+0x174/0x490
[   53.834910]        netlink_rcv_skb+0x42/0x100
[   53.834911]        netlink_unicast+0x18c/0x250
[   53.834912]        netlink_sendmsg+0x227/0x460
[   53.834914]        sock_sendmsg+0x59/0x60
[   53.834915]        ____sys_sendmsg+0x1f5/0x230
[   53.834916]        ___sys_sendmsg+0x70/0xb0
[   53.834917]        __sys_sendmsg+0x54/0xa0
[   53.834919]        do_syscall_64+0x33/0x40
[   53.834920]        entry_SYSCALL_64_after_hwframe+0x44/0xa9
[   53.834921]
[   53.834921] -> #0 (&ar->conf_mutex){+.+.}-{3:3}:
[   53.834923]        check_prev_add+0x98/0x9f0
[   53.834925]        validate_chain+0x404/0x6c0
[   53.834926]        __lock_acquire+0x3bf/0x6e0
[   53.834927]        lock_acquire+0xb6/0x270
[   53.834929]        __mutex_lock+0x88/0x8e0
[   53.834934]        ath11k_mac_op_config+0x16/0x30 [ath11k]
[   53.834935]        ieee80211_hw_config+0xb3/0x270
[   53.834937]        ieee80211_set_associated+0x17c/0x360
[   53.834938]        ieee80211_assoc_success.constprop.0+0x5a2/0xc80
[   53.834940]        ieee80211_rx_mgmt_assoc_resp+0x16a/0x350
[   53.834941]        ieee80211_sta_rx_queued_mgmt+0xca/0x410
[   53.834943]        ieee80211_iface_work+0x1f3/0x350
[   53.834945]        process_one_work+0x265/0x5d0
[   53.834946]        worker_thread+0x49/0x300
[   53.834948]        kthread+0x135/0x150
[   53.834949]        ret_from_fork+0x22/0x30
[   53.834950]
[   53.834950] other info that might help us debug this:
[   53.834950]
[   53.834951]  Possible unsafe locking scenario:
[   53.834951]
[   53.834952]        CPU0                    CPU1
[   53.834952]        ----                    ----
[   53.834953]   lock(&local->iflist_mtx);
[   53.834954]                                lock(&ar->conf_mutex);
[   53.834955]                                lock(&local->iflist_mtx);
[   53.834956]   lock(&ar->conf_mutex);
[   53.834957]
[   53.834957]  *** DEADLOCK ***
[   53.834957]
[   53.834958] 4 locks held by kworker/u16:3/166:
[   53.834959]  #0: ffff8c4b37c22948 ((wq_completion)phy0){+.+.}-{0:0}, at: process_one_work+0x1d3/0x5d0
[   53.834961]  #1: ffffa98300abfe70 ((work_completion)(&sdata->work)){+.+.}-{0:0}, at: process_one_work+0x1d3/0x5d0
[   53.834963]  #2: ffff8c4b371e4cd0 (&wdev->mtx){+.+.}-{3:3}, at: ieee80211_sta_rx_queued_mgmt+0x4b/0x410
[   53.834965]  #3: ffff8c4b37182808 (&local->iflist_mtx){+.+.}-{3:3}, at: ieee80211_set_associated+0x167/0x360
[   53.834968]
[   53.834968] stack backtrace:
[   53.834969] CPU: 1 PID: 166 Comm: kworker/u16:3 Not tainted 5.9.0-rc5-wt-ath+ #198
[   53.834970] Hardware name: Intel(R) Client Systems NUC8i7HVK/NUC8i7HVB, BIOS HNKBLi70.86A.0049.2018.0801.1601 08/01/2018
[   53.834972] Workqueue: phy0 ieee80211_iface_work
[   53.834974] Call Trace:
[   53.834976]  dump_stack+0x77/0xa0
[   53.834978]  check_noncircular+0x15d/0x180
[   53.834980]  check_prev_add+0x98/0x9f0
[   53.834982]  ? add_chain_cache+0x143/0x440
[   53.834984]  validate_chain+0x404/0x6c0
[   53.834986]  __lock_acquire+0x3bf/0x6e0
[   53.834988]  lock_acquire+0xb6/0x270
[   53.834993]  ? ath11k_mac_op_config+0x16/0x30 [ath11k]
[   53.834999]  ? ath11k_mac_op_config+0x16/0x30 [ath11k]
[   53.835001]  __mutex_lock+0x88/0x8e0
[   53.835006]  ? ath11k_mac_op_config+0x16/0x30 [ath11k]
[   53.835007]  ? sched_clock_cpu+0xc/0xb0
[   53.835009]  ? __lock_release+0x179/0x2c0
[   53.835014]  ath11k_mac_op_config+0x16/0x30 [ath11k]
[   53.835016]  ieee80211_hw_config+0xb3/0x270
[   53.835018]  ieee80211_set_associated+0x17c/0x360
[   53.835019]  ieee80211_assoc_success.constprop.0+0x5a2/0xc80
[   53.835021]  ? lockdep_hardirqs_on_prepare.part.0+0x9f/0x140
[   53.835023]  ? cmpxchg_double_slab.constprop.0+0x185/0x1a0
[   53.835025]  ? trace_hardirqs_on+0x1c/0x100
[   53.835027]  ? __slab_free+0x8f/0x330
[   53.835029]  ? slab_free_freelist_hook+0xf8/0x150
[   53.835031]  ? ieee802_11_parse_elems_crc+0x147/0x1d0
[   53.835032]  ? kfree+0x2b0/0x2d0
[   53.835034]  ? ieee802_11_parse_elems_crc+0x147/0x1d0
[   53.835036]  ieee80211_rx_mgmt_assoc_resp+0x16a/0x350
[   53.835041]  ieee80211_sta_rx_queued_mgmt+0xca/0x410
[   53.835043]  ? __lock_acquire+0x3bf/0x6e0
[   53.835045]  ? lock_acquire+0xb6/0x270
[   53.835046]  ? skb_dequeue+0x13/0x70
[   53.835048]  ? find_held_lock+0x32/0x90
[   53.835049]  ? sched_clock_cpu+0xc/0xb0
[   53.835051]  ? mark_held_locks+0x50/0x80
[   53.835053]  ? lockdep_hardirqs_on_prepare.part.0+0x9f/0x140
[   53.835054]  ? _raw_spin_unlock_irqrestore+0x34/0x40
[   53.835056]  ? trace_hardirqs_on+0x1c/0x100
[   53.835058]  ieee80211_iface_work+0x1f3/0x350
[   53.835060]  process_one_work+0x265/0x5d0
[   53.835062]  worker_thread+0x49/0x300
[   53.835063]  ? process_one_work+0x5d0/0x5d0
[   53.835065]  kthread+0x135/0x150
[   53.835066]  ? kthread_create_worker_on_cpu+0x60/0x60
[   53.835068]  ret_from_fork+0x22/0x30
[   53.835075] wlp6s0: associated
[   53.835132] IPv6: ADDRCONF(NETDEV_CHANGE): wlp6s0: link becomes ready

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1

Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
---
 drivers/net/wireless/ath/ath11k/mac.c | 11 +----------
 1 file changed, 1 insertion(+), 10 deletions(-)

diff --git a/drivers/net/wireless/ath/ath11k/mac.c b/drivers/net/wireless/ath/ath11k/mac.c
index c43844ed6b61..76e218e53fe7 100644
--- a/drivers/net/wireless/ath/ath11k/mac.c
+++ b/drivers/net/wireless/ath/ath11k/mac.c
@@ -758,21 +758,12 @@ static int ath11k_monitor_vdev_up(struct ath11k *ar, int vdev_id)
 
 static int ath11k_mac_op_config(struct ieee80211_hw *hw, u32 changed)
 {
-	struct ath11k *ar = hw->priv;
-	int ret = 0;
-
 	/* mac80211 requires this op to be present and that's why
 	 * there's an empty function, this can be extended when
 	 * required.
 	 */
 
-	mutex_lock(&ar->conf_mutex);
-
-	/* TODO: Handle configuration changes as appropriate */
-
-	mutex_unlock(&ar->conf_mutex);
-
-	return ret;
+	return 0;
 }
 
 static int ath11k_mac_setup_bcn_tmpl(struct ath11k_vif *arvif)
-- 
2.7.4


  parent reply	other threads:[~2020-09-30 10:51 UTC|newest]

Thread overview: 14+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2020-09-30 10:51 [PATCH 0/5] ath11k: qca6390: packet log support and fixes for crashes Kalle Valo
2020-09-30 10:51 ` Kalle Valo
2020-09-30 10:51 ` [PATCH 1/5] ath11k: add packet log support for QCA6390 Kalle Valo
2020-09-30 10:51   ` Kalle Valo
2020-10-01 19:32   ` Kalle Valo
2020-10-01 19:32   ` Kalle Valo
2020-09-30 10:51 ` [PATCH 2/5] ath11k: pci: fix rmmod crash Kalle Valo
2020-09-30 10:51   ` Kalle Valo
2020-09-30 10:51 ` Kalle Valo [this message]
2020-09-30 10:51   ` [PATCH 3/5] ath11k: mac: remove unused conf_mutex to solve a deadlock Kalle Valo
2020-09-30 10:51 ` [PATCH 4/5] ath11k: fix warning caused by lockdep_assert_held Kalle Valo
2020-09-30 10:51   ` Kalle Valo
2020-09-30 10:51 ` [PATCH 5/5] ath11k: debugfs: fix crash during rmmod Kalle Valo
2020-09-30 10:51   ` Kalle Valo

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1601463073-12106-4-git-send-email-kvalo@codeaurora.org \
    --to=kvalo@codeaurora.org \
    --cc=ath11k@lists.infradead.org \
    --cc=linux-wireless@vger.kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body. 
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.