* [PATCH V9 1/3] dt-bindings: rtc: zynqmp: Add clock information
@ 2022-06-24 12:02 ` Srinivas Neeli
0 siblings, 0 replies; 10+ messages in thread
From: Srinivas Neeli @ 2022-06-24 12:02 UTC (permalink / raw)
To: a.zummo, alexandre.belloni, robh+dt, srinivas.neeli,
neelisrinivas18, krzysztof.kozlowski+dt, michal.simek, sgoud,
shubhraj
Cc: devicetree, linux-rtc, linux-arm-kernel, linux-kernel, git, git,
Srinivas Neeli, Rob Herring
Added clock information and deprecated calibration support.
Signed-off-by: Srinivas Neeli <srinivas.neeli@xilinx.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---
Changes in V9:
-Updated clock information in clock-names.
Changes in V8:
-None
Changes in V7:
-None
Changes in V6:
-Removed dtc warnings.
Changes in V5:
-Removed quotes and _clk suffix from clocknames.
Changes in V4:
- Deprecated calibrtion support
Changes in V3:
- New patch
---
.../devicetree/bindings/rtc/xlnx,zynqmp-rtc.yaml | 12 +++++++++++-
1 file changed, 11 insertions(+), 1 deletion(-)
diff --git a/Documentation/devicetree/bindings/rtc/xlnx,zynqmp-rtc.yaml b/Documentation/devicetree/bindings/rtc/xlnx,zynqmp-rtc.yaml
index bdb72d3ddf2a..9dfe2cc5966a 100644
--- a/Documentation/devicetree/bindings/rtc/xlnx,zynqmp-rtc.yaml
+++ b/Documentation/devicetree/bindings/rtc/xlnx,zynqmp-rtc.yaml
@@ -23,8 +23,15 @@ properties:
reg:
maxItems: 1
+ clocks:
+ maxItems: 1
+
+ clock-names:
+ items:
+ - const: rtc
+
interrupts:
- minItems: 2
+ maxItems: 2
interrupt-names:
items:
@@ -39,6 +46,7 @@ properties:
minimum: 0x1
maximum: 0x1FFFFF
default: 0x198233
+ deprecated: true
required:
- compatible
@@ -61,5 +69,7 @@ examples:
interrupts = <0 26 4>, <0 27 4>;
interrupt-names = "alarm", "sec";
calibration = <0x198233>;
+ clock-names = "rtc_clk";
+ clocks = <&rtc_clk>;
};
};
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 10+ messages in thread* [PATCH V9 2/3] rtc: zynqmp: Updated calibration value
2022-06-24 12:02 ` Srinivas Neeli
@ 2022-06-24 12:02 ` Srinivas Neeli
-1 siblings, 0 replies; 10+ messages in thread
From: Srinivas Neeli @ 2022-06-24 12:02 UTC (permalink / raw)
To: a.zummo, alexandre.belloni, robh+dt, srinivas.neeli,
neelisrinivas18, krzysztof.kozlowski+dt, michal.simek, sgoud,
shubhraj
Cc: devicetree, linux-rtc, linux-arm-kernel, linux-kernel, git, git,
Srinivas Neeli, Peter Korsgaard
As per RTC spec default calibration value is 0x7FFF.
We are in process to update the 0x7FFF as default value in
the next version of TRM.
Signed-off-by: Srinivas Neeli <srinivas.neeli@xilinx.com>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
---
Changes in V8
-None, just swapped 2/3 and 3/3 patches from V7.
Changes in V7:
-New patch
-TRM not updated yet, Internal design document contains 0x7FFF as
default value. TRM Will update in next release.
---
drivers/rtc/rtc-zynqmp.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/rtc/rtc-zynqmp.c b/drivers/rtc/rtc-zynqmp.c
index f440bb52be92..5da33d760419 100644
--- a/drivers/rtc/rtc-zynqmp.c
+++ b/drivers/rtc/rtc-zynqmp.c
@@ -36,7 +36,7 @@
#define RTC_OSC_EN BIT(24)
#define RTC_BATT_EN BIT(31)
-#define RTC_CALIB_DEF 0x198233
+#define RTC_CALIB_DEF 0x7FFF
#define RTC_CALIB_MASK 0x1FFFFF
#define RTC_ALRM_MASK BIT(1)
#define RTC_MSEC 1000
--
2.25.1
^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH V9 2/3] rtc: zynqmp: Updated calibration value
@ 2022-06-24 12:02 ` Srinivas Neeli
0 siblings, 0 replies; 10+ messages in thread
From: Srinivas Neeli @ 2022-06-24 12:02 UTC (permalink / raw)
To: a.zummo, alexandre.belloni, robh+dt, srinivas.neeli,
neelisrinivas18, krzysztof.kozlowski+dt, michal.simek, sgoud,
shubhraj
Cc: devicetree, linux-rtc, linux-arm-kernel, linux-kernel, git, git,
Srinivas Neeli, Peter Korsgaard
As per RTC spec default calibration value is 0x7FFF.
We are in process to update the 0x7FFF as default value in
the next version of TRM.
Signed-off-by: Srinivas Neeli <srinivas.neeli@xilinx.com>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
---
Changes in V8
-None, just swapped 2/3 and 3/3 patches from V7.
Changes in V7:
-New patch
-TRM not updated yet, Internal design document contains 0x7FFF as
default value. TRM Will update in next release.
---
drivers/rtc/rtc-zynqmp.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/rtc/rtc-zynqmp.c b/drivers/rtc/rtc-zynqmp.c
index f440bb52be92..5da33d760419 100644
--- a/drivers/rtc/rtc-zynqmp.c
+++ b/drivers/rtc/rtc-zynqmp.c
@@ -36,7 +36,7 @@
#define RTC_OSC_EN BIT(24)
#define RTC_BATT_EN BIT(31)
-#define RTC_CALIB_DEF 0x198233
+#define RTC_CALIB_DEF 0x7FFF
#define RTC_CALIB_MASK 0x1FFFFF
#define RTC_ALRM_MASK BIT(1)
#define RTC_MSEC 1000
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH V9 3/3] rtc: zynqmp: Add calibration set and get support
2022-06-24 12:02 ` Srinivas Neeli
@ 2022-06-24 12:02 ` Srinivas Neeli
-1 siblings, 0 replies; 10+ messages in thread
From: Srinivas Neeli @ 2022-06-24 12:02 UTC (permalink / raw)
To: a.zummo, alexandre.belloni, robh+dt, srinivas.neeli,
neelisrinivas18, krzysztof.kozlowski+dt, michal.simek, sgoud,
shubhraj
Cc: devicetree, linux-rtc, linux-arm-kernel, linux-kernel, git, git,
Srinivas Neeli
Zynqmp RTC controller has a calibration feature to compensate
time deviation due to input clock inaccuracy.
Set and get calibration API's are used for setting and getting
calibration value from the controller calibration register.
Signed-off-by: Srinivas Neeli <srinivas.neeli@xilinx.com>
---
Changes in V9:
-None
Changes in V8:
-None
Changes in V7:
-Removed calibration default value update from this patch.
Changes in V6:
-None
Changes in V5:
-None
Changes in V4:
-Updated MIN and MAX calibration values.
Changes in V3:
-Calculated tick_mult using crystal frequency.
-Calibration register updating based on crystal frequency in probe.
-Supressed MIN an MAX calibration values,Will send separate patch in future.
Changes in V2:
-Removed unused macro.
-Updated code with review comments.
---
drivers/rtc/rtc-zynqmp.c | 113 ++++++++++++++++++++++++++++++++-------
1 file changed, 94 insertions(+), 19 deletions(-)
diff --git a/drivers/rtc/rtc-zynqmp.c b/drivers/rtc/rtc-zynqmp.c
index 5da33d760419..1dd389b891fe 100644
--- a/drivers/rtc/rtc-zynqmp.c
+++ b/drivers/rtc/rtc-zynqmp.c
@@ -6,6 +6,7 @@
*
*/
+#include <linux/clk.h>
#include <linux/delay.h>
#include <linux/init.h>
#include <linux/io.h>
@@ -40,13 +41,19 @@
#define RTC_CALIB_MASK 0x1FFFFF
#define RTC_ALRM_MASK BIT(1)
#define RTC_MSEC 1000
+#define RTC_FR_MASK 0xF0000
+#define RTC_FR_MAX_TICKS 16
+#define RTC_PPB 1000000000LL
+#define RTC_MIN_OFFSET -32768000
+#define RTC_MAX_OFFSET 32767000
struct xlnx_rtc_dev {
struct rtc_device *rtc;
void __iomem *reg_base;
int alarm_irq;
int sec_irq;
- unsigned int calibval;
+ struct clk *rtc_clk;
+ unsigned int freq;
};
static int xlnx_rtc_set_time(struct device *dev, struct rtc_time *tm)
@@ -61,13 +68,6 @@ static int xlnx_rtc_set_time(struct device *dev, struct rtc_time *tm)
*/
new_time = rtc_tm_to_time64(tm) + 1;
- /*
- * Writing into calibration register will clear the Tick Counter and
- * force the next second to be signaled exactly in 1 second period
- */
- xrtcdev->calibval &= RTC_CALIB_MASK;
- writel(xrtcdev->calibval, (xrtcdev->reg_base + RTC_CALIB_WR));
-
writel(new_time, xrtcdev->reg_base + RTC_SET_TM_WR);
/*
@@ -173,15 +173,76 @@ static void xlnx_init_rtc(struct xlnx_rtc_dev *xrtcdev)
rtc_ctrl = readl(xrtcdev->reg_base + RTC_CTRL);
rtc_ctrl |= RTC_BATT_EN;
writel(rtc_ctrl, xrtcdev->reg_base + RTC_CTRL);
+}
- /*
- * Based on crystal freq of 33.330 KHz
- * set the seconds counter and enable, set fractions counter
- * to default value suggested as per design spec
- * to correct RTC delay in frequency over period of time.
+static int xlnx_rtc_read_offset(struct device *dev, long *offset)
+{
+ struct xlnx_rtc_dev *xrtcdev = dev_get_drvdata(dev);
+ unsigned long long rtc_ppb = RTC_PPB;
+ unsigned int tick_mult = do_div(rtc_ppb, xrtcdev->freq);
+ unsigned int calibval;
+ long offset_val;
+
+ calibval = readl(xrtcdev->reg_base + RTC_CALIB_RD);
+ /* Offset with seconds ticks */
+ offset_val = calibval & RTC_TICK_MASK;
+ offset_val = offset_val - RTC_CALIB_DEF;
+ offset_val = offset_val * tick_mult;
+
+ /* Offset with fractional ticks */
+ if (calibval & RTC_FR_EN)
+ offset_val += ((calibval & RTC_FR_MASK) >> RTC_FR_DATSHIFT)
+ * (tick_mult / RTC_FR_MAX_TICKS);
+ *offset = offset_val;
+
+ return 0;
+}
+
+static int xlnx_rtc_set_offset(struct device *dev, long offset)
+{
+ struct xlnx_rtc_dev *xrtcdev = dev_get_drvdata(dev);
+ unsigned long long rtc_ppb = RTC_PPB;
+ unsigned int tick_mult = do_div(rtc_ppb, xrtcdev->freq);
+ unsigned char fract_tick;
+ unsigned int calibval;
+ short int max_tick;
+ int fract_offset;
+
+ if (offset < RTC_MIN_OFFSET || offset > RTC_MAX_OFFSET)
+ return -ERANGE;
+
+ /* Number ticks for given offset */
+ max_tick = div_s64_rem(offset, tick_mult, &fract_offset);
+
+ /* Number fractional ticks for given offset */
+ if (fract_offset) {
+ if (fract_offset < 0) {
+ fract_offset = fract_offset + tick_mult;
+ max_tick--;
+ }
+ if (fract_offset > (tick_mult / RTC_FR_MAX_TICKS)) {
+ for (fract_tick = 1; fract_tick < 16; fract_tick++) {
+ if (fract_offset <=
+ (fract_tick *
+ (tick_mult / RTC_FR_MAX_TICKS)))
+ break;
+ }
+ }
+ }
+
+ /* Zynqmp RTC uses second and fractional tick
+ * counters for compensation
*/
- xrtcdev->calibval &= RTC_CALIB_MASK;
- writel(xrtcdev->calibval, (xrtcdev->reg_base + RTC_CALIB_WR));
+ calibval = max_tick + RTC_CALIB_DEF;
+
+ if (fract_tick)
+ calibval |= RTC_FR_EN;
+
+ calibval |= (fract_tick << RTC_FR_DATSHIFT);
+
+ writel(calibval, (xrtcdev->reg_base + RTC_CALIB_WR));
+
+ return 0;
}
static const struct rtc_class_ops xlnx_rtc_ops = {
@@ -190,6 +251,8 @@ static const struct rtc_class_ops xlnx_rtc_ops = {
.read_alarm = xlnx_rtc_read_alarm,
.set_alarm = xlnx_rtc_set_alarm,
.alarm_irq_enable = xlnx_rtc_alarm_irq_enable,
+ .read_offset = xlnx_rtc_read_offset,
+ .set_offset = xlnx_rtc_set_offset,
};
static irqreturn_t xlnx_rtc_interrupt(int irq, void *id)
@@ -255,10 +318,22 @@ static int xlnx_rtc_probe(struct platform_device *pdev)
return ret;
}
- ret = of_property_read_u32(pdev->dev.of_node, "calibration",
- &xrtcdev->calibval);
- if (ret)
- xrtcdev->calibval = RTC_CALIB_DEF;
+ /* Getting the rtc_clk info */
+ xrtcdev->rtc_clk = devm_clk_get_optional(&pdev->dev, "rtc_clk");
+ if (IS_ERR(xrtcdev->rtc_clk)) {
+ if (PTR_ERR(xrtcdev->rtc_clk) != -EPROBE_DEFER)
+ dev_warn(&pdev->dev, "Device clock not found.\n");
+ }
+ xrtcdev->freq = clk_get_rate(xrtcdev->rtc_clk);
+ if (!xrtcdev->freq) {
+ ret = of_property_read_u32(pdev->dev.of_node, "calibration",
+ &xrtcdev->freq);
+ if (ret)
+ xrtcdev->freq = RTC_CALIB_DEF;
+ }
+ ret = readl(xrtcdev->reg_base + RTC_CALIB_RD);
+ if (!ret)
+ writel(xrtcdev->freq, (xrtcdev->reg_base + RTC_CALIB_WR));
xlnx_init_rtc(xrtcdev);
--
2.25.1
^ permalink raw reply related [flat|nested] 10+ messages in thread* [PATCH V9 3/3] rtc: zynqmp: Add calibration set and get support
@ 2022-06-24 12:02 ` Srinivas Neeli
0 siblings, 0 replies; 10+ messages in thread
From: Srinivas Neeli @ 2022-06-24 12:02 UTC (permalink / raw)
To: a.zummo, alexandre.belloni, robh+dt, srinivas.neeli,
neelisrinivas18, krzysztof.kozlowski+dt, michal.simek, sgoud,
shubhraj
Cc: devicetree, linux-rtc, linux-arm-kernel, linux-kernel, git, git,
Srinivas Neeli
Zynqmp RTC controller has a calibration feature to compensate
time deviation due to input clock inaccuracy.
Set and get calibration API's are used for setting and getting
calibration value from the controller calibration register.
Signed-off-by: Srinivas Neeli <srinivas.neeli@xilinx.com>
---
Changes in V9:
-None
Changes in V8:
-None
Changes in V7:
-Removed calibration default value update from this patch.
Changes in V6:
-None
Changes in V5:
-None
Changes in V4:
-Updated MIN and MAX calibration values.
Changes in V3:
-Calculated tick_mult using crystal frequency.
-Calibration register updating based on crystal frequency in probe.
-Supressed MIN an MAX calibration values,Will send separate patch in future.
Changes in V2:
-Removed unused macro.
-Updated code with review comments.
---
drivers/rtc/rtc-zynqmp.c | 113 ++++++++++++++++++++++++++++++++-------
1 file changed, 94 insertions(+), 19 deletions(-)
diff --git a/drivers/rtc/rtc-zynqmp.c b/drivers/rtc/rtc-zynqmp.c
index 5da33d760419..1dd389b891fe 100644
--- a/drivers/rtc/rtc-zynqmp.c
+++ b/drivers/rtc/rtc-zynqmp.c
@@ -6,6 +6,7 @@
*
*/
+#include <linux/clk.h>
#include <linux/delay.h>
#include <linux/init.h>
#include <linux/io.h>
@@ -40,13 +41,19 @@
#define RTC_CALIB_MASK 0x1FFFFF
#define RTC_ALRM_MASK BIT(1)
#define RTC_MSEC 1000
+#define RTC_FR_MASK 0xF0000
+#define RTC_FR_MAX_TICKS 16
+#define RTC_PPB 1000000000LL
+#define RTC_MIN_OFFSET -32768000
+#define RTC_MAX_OFFSET 32767000
struct xlnx_rtc_dev {
struct rtc_device *rtc;
void __iomem *reg_base;
int alarm_irq;
int sec_irq;
- unsigned int calibval;
+ struct clk *rtc_clk;
+ unsigned int freq;
};
static int xlnx_rtc_set_time(struct device *dev, struct rtc_time *tm)
@@ -61,13 +68,6 @@ static int xlnx_rtc_set_time(struct device *dev, struct rtc_time *tm)
*/
new_time = rtc_tm_to_time64(tm) + 1;
- /*
- * Writing into calibration register will clear the Tick Counter and
- * force the next second to be signaled exactly in 1 second period
- */
- xrtcdev->calibval &= RTC_CALIB_MASK;
- writel(xrtcdev->calibval, (xrtcdev->reg_base + RTC_CALIB_WR));
-
writel(new_time, xrtcdev->reg_base + RTC_SET_TM_WR);
/*
@@ -173,15 +173,76 @@ static void xlnx_init_rtc(struct xlnx_rtc_dev *xrtcdev)
rtc_ctrl = readl(xrtcdev->reg_base + RTC_CTRL);
rtc_ctrl |= RTC_BATT_EN;
writel(rtc_ctrl, xrtcdev->reg_base + RTC_CTRL);
+}
- /*
- * Based on crystal freq of 33.330 KHz
- * set the seconds counter and enable, set fractions counter
- * to default value suggested as per design spec
- * to correct RTC delay in frequency over period of time.
+static int xlnx_rtc_read_offset(struct device *dev, long *offset)
+{
+ struct xlnx_rtc_dev *xrtcdev = dev_get_drvdata(dev);
+ unsigned long long rtc_ppb = RTC_PPB;
+ unsigned int tick_mult = do_div(rtc_ppb, xrtcdev->freq);
+ unsigned int calibval;
+ long offset_val;
+
+ calibval = readl(xrtcdev->reg_base + RTC_CALIB_RD);
+ /* Offset with seconds ticks */
+ offset_val = calibval & RTC_TICK_MASK;
+ offset_val = offset_val - RTC_CALIB_DEF;
+ offset_val = offset_val * tick_mult;
+
+ /* Offset with fractional ticks */
+ if (calibval & RTC_FR_EN)
+ offset_val += ((calibval & RTC_FR_MASK) >> RTC_FR_DATSHIFT)
+ * (tick_mult / RTC_FR_MAX_TICKS);
+ *offset = offset_val;
+
+ return 0;
+}
+
+static int xlnx_rtc_set_offset(struct device *dev, long offset)
+{
+ struct xlnx_rtc_dev *xrtcdev = dev_get_drvdata(dev);
+ unsigned long long rtc_ppb = RTC_PPB;
+ unsigned int tick_mult = do_div(rtc_ppb, xrtcdev->freq);
+ unsigned char fract_tick;
+ unsigned int calibval;
+ short int max_tick;
+ int fract_offset;
+
+ if (offset < RTC_MIN_OFFSET || offset > RTC_MAX_OFFSET)
+ return -ERANGE;
+
+ /* Number ticks for given offset */
+ max_tick = div_s64_rem(offset, tick_mult, &fract_offset);
+
+ /* Number fractional ticks for given offset */
+ if (fract_offset) {
+ if (fract_offset < 0) {
+ fract_offset = fract_offset + tick_mult;
+ max_tick--;
+ }
+ if (fract_offset > (tick_mult / RTC_FR_MAX_TICKS)) {
+ for (fract_tick = 1; fract_tick < 16; fract_tick++) {
+ if (fract_offset <=
+ (fract_tick *
+ (tick_mult / RTC_FR_MAX_TICKS)))
+ break;
+ }
+ }
+ }
+
+ /* Zynqmp RTC uses second and fractional tick
+ * counters for compensation
*/
- xrtcdev->calibval &= RTC_CALIB_MASK;
- writel(xrtcdev->calibval, (xrtcdev->reg_base + RTC_CALIB_WR));
+ calibval = max_tick + RTC_CALIB_DEF;
+
+ if (fract_tick)
+ calibval |= RTC_FR_EN;
+
+ calibval |= (fract_tick << RTC_FR_DATSHIFT);
+
+ writel(calibval, (xrtcdev->reg_base + RTC_CALIB_WR));
+
+ return 0;
}
static const struct rtc_class_ops xlnx_rtc_ops = {
@@ -190,6 +251,8 @@ static const struct rtc_class_ops xlnx_rtc_ops = {
.read_alarm = xlnx_rtc_read_alarm,
.set_alarm = xlnx_rtc_set_alarm,
.alarm_irq_enable = xlnx_rtc_alarm_irq_enable,
+ .read_offset = xlnx_rtc_read_offset,
+ .set_offset = xlnx_rtc_set_offset,
};
static irqreturn_t xlnx_rtc_interrupt(int irq, void *id)
@@ -255,10 +318,22 @@ static int xlnx_rtc_probe(struct platform_device *pdev)
return ret;
}
- ret = of_property_read_u32(pdev->dev.of_node, "calibration",
- &xrtcdev->calibval);
- if (ret)
- xrtcdev->calibval = RTC_CALIB_DEF;
+ /* Getting the rtc_clk info */
+ xrtcdev->rtc_clk = devm_clk_get_optional(&pdev->dev, "rtc_clk");
+ if (IS_ERR(xrtcdev->rtc_clk)) {
+ if (PTR_ERR(xrtcdev->rtc_clk) != -EPROBE_DEFER)
+ dev_warn(&pdev->dev, "Device clock not found.\n");
+ }
+ xrtcdev->freq = clk_get_rate(xrtcdev->rtc_clk);
+ if (!xrtcdev->freq) {
+ ret = of_property_read_u32(pdev->dev.of_node, "calibration",
+ &xrtcdev->freq);
+ if (ret)
+ xrtcdev->freq = RTC_CALIB_DEF;
+ }
+ ret = readl(xrtcdev->reg_base + RTC_CALIB_RD);
+ if (!ret)
+ writel(xrtcdev->freq, (xrtcdev->reg_base + RTC_CALIB_WR));
xlnx_init_rtc(xrtcdev);
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 10+ messages in thread
* Re: [PATCH V9 1/3] dt-bindings: rtc: zynqmp: Add clock information
2022-06-24 12:02 ` Srinivas Neeli
@ 2022-06-24 17:26 ` Rob Herring
-1 siblings, 0 replies; 10+ messages in thread
From: Rob Herring @ 2022-06-24 17:26 UTC (permalink / raw)
To: Srinivas Neeli
Cc: linux-arm-kernel, shubhraj, neelisrinivas18, a.zummo, sgoud,
linux-rtc, linux-kernel, robh+dt, git, alexandre.belloni,
srinivas.neeli, git, devicetree, krzysztof.kozlowski+dt,
michal.simek
On Fri, 24 Jun 2022 17:32:01 +0530, Srinivas Neeli wrote:
> Added clock information and deprecated calibration support.
>
> Signed-off-by: Srinivas Neeli <srinivas.neeli@xilinx.com>
> Reviewed-by: Rob Herring <robh@kernel.org>
> ---
> Changes in V9:
> -Updated clock information in clock-names.
> Changes in V8:
> -None
> Changes in V7:
> -None
> Changes in V6:
> -Removed dtc warnings.
> Changes in V5:
> -Removed quotes and _clk suffix from clocknames.
> Changes in V4:
> - Deprecated calibrtion support
> Changes in V3:
> - New patch
> ---
> .../devicetree/bindings/rtc/xlnx,zynqmp-rtc.yaml | 12 +++++++++++-
> 1 file changed, 11 insertions(+), 1 deletion(-)
>
My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check'
on your patch (DT_CHECKER_FLAGS is new in v5.13):
yamllint warnings/errors:
dtschema/dtc warnings/errors:
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/rtc/xlnx,zynqmp-rtc.example.dtb: rtc@ffa60000: clock-names:0: 'rtc' was expected
From schema: /builds/robherring/linux-dt-review/Documentation/devicetree/bindings/rtc/xlnx,zynqmp-rtc.yaml
doc reference errors (make refcheckdocs):
See https://patchwork.ozlabs.org/patch/
This check can fail if there are any dependencies. The base for a patch
series is generally the most recent rc1.
If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure 'yamllint' is installed and dt-schema is up to
date:
pip3 install dtschema --upgrade
Please check and re-submit.
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [PATCH V9 1/3] dt-bindings: rtc: zynqmp: Add clock information
@ 2022-06-24 17:26 ` Rob Herring
0 siblings, 0 replies; 10+ messages in thread
From: Rob Herring @ 2022-06-24 17:26 UTC (permalink / raw)
To: Srinivas Neeli
Cc: linux-arm-kernel, shubhraj, neelisrinivas18, a.zummo, sgoud,
linux-rtc, linux-kernel, robh+dt, git, alexandre.belloni,
srinivas.neeli, git, devicetree, krzysztof.kozlowski+dt,
michal.simek
On Fri, 24 Jun 2022 17:32:01 +0530, Srinivas Neeli wrote:
> Added clock information and deprecated calibration support.
>
> Signed-off-by: Srinivas Neeli <srinivas.neeli@xilinx.com>
> Reviewed-by: Rob Herring <robh@kernel.org>
> ---
> Changes in V9:
> -Updated clock information in clock-names.
> Changes in V8:
> -None
> Changes in V7:
> -None
> Changes in V6:
> -Removed dtc warnings.
> Changes in V5:
> -Removed quotes and _clk suffix from clocknames.
> Changes in V4:
> - Deprecated calibrtion support
> Changes in V3:
> - New patch
> ---
> .../devicetree/bindings/rtc/xlnx,zynqmp-rtc.yaml | 12 +++++++++++-
> 1 file changed, 11 insertions(+), 1 deletion(-)
>
My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check'
on your patch (DT_CHECKER_FLAGS is new in v5.13):
yamllint warnings/errors:
dtschema/dtc warnings/errors:
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/rtc/xlnx,zynqmp-rtc.example.dtb: rtc@ffa60000: clock-names:0: 'rtc' was expected
From schema: /builds/robherring/linux-dt-review/Documentation/devicetree/bindings/rtc/xlnx,zynqmp-rtc.yaml
doc reference errors (make refcheckdocs):
See https://patchwork.ozlabs.org/patch/
This check can fail if there are any dependencies. The base for a patch
series is generally the most recent rc1.
If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure 'yamllint' is installed and dt-schema is up to
date:
pip3 install dtschema --upgrade
Please check and re-submit.
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [PATCH V9 1/3] dt-bindings: rtc: zynqmp: Add clock information
2022-06-24 12:02 ` Srinivas Neeli
@ 2022-06-25 20:38 ` Krzysztof Kozlowski
-1 siblings, 0 replies; 10+ messages in thread
From: Krzysztof Kozlowski @ 2022-06-25 20:38 UTC (permalink / raw)
To: Srinivas Neeli, a.zummo, alexandre.belloni, robh+dt,
srinivas.neeli, neelisrinivas18, krzysztof.kozlowski+dt,
michal.simek, sgoud, shubhraj
Cc: devicetree, linux-rtc, linux-arm-kernel, linux-kernel, git, git,
Rob Herring
On 24/06/2022 14:02, Srinivas Neeli wrote:
> Added clock information and deprecated calibration support.
>
> Signed-off-by: Srinivas Neeli <srinivas.neeli@xilinx.com>
> Reviewed-by: Rob Herring <robh@kernel.org>
> ---
> Changes in V9:
> -Updated clock information in clock-names.
> Changes in V8:
> -None
> Changes in V7:
> -None
> Changes in V6:
> -Removed dtc warnings.
> Changes in V5:
> -Removed quotes and _clk suffix from clocknames.
> Changes in V4:
> - Deprecated calibrtion support
> Changes in V3:
> - New patch
> ---
> .../devicetree/bindings/rtc/xlnx,zynqmp-rtc.yaml | 12 +++++++++++-
> 1 file changed, 11 insertions(+), 1 deletion(-)
>
> diff --git a/Documentation/devicetree/bindings/rtc/xlnx,zynqmp-rtc.yaml b/Documentation/devicetree/bindings/rtc/xlnx,zynqmp-rtc.yaml
> index bdb72d3ddf2a..9dfe2cc5966a 100644
> --- a/Documentation/devicetree/bindings/rtc/xlnx,zynqmp-rtc.yaml
> +++ b/Documentation/devicetree/bindings/rtc/xlnx,zynqmp-rtc.yaml
> @@ -23,8 +23,15 @@ properties:
> reg:
> maxItems: 1
>
> + clocks:
> + maxItems: 1
> +
> + clock-names:
> + items:
> + - const: rtc
> +
> interrupts:
> - minItems: 2
> + maxItems: 2
>
> interrupt-names:
> items:
> @@ -39,6 +46,7 @@ properties:
> minimum: 0x1
> maximum: 0x1FFFFF
> default: 0x198233
> + deprecated: true
>
> required:
> - compatible
> @@ -61,5 +69,7 @@ examples:
> interrupts = <0 26 4>, <0 27 4>;
> interrupt-names = "alarm", "sec";
> calibration = <0x198233>;
> + clock-names = "rtc_clk";
> + clocks = <&rtc_clk>;
Please test your bindings with `make dt_binding_check` before sending.
Best regards,
Krzysztof
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [PATCH V9 1/3] dt-bindings: rtc: zynqmp: Add clock information
@ 2022-06-25 20:38 ` Krzysztof Kozlowski
0 siblings, 0 replies; 10+ messages in thread
From: Krzysztof Kozlowski @ 2022-06-25 20:38 UTC (permalink / raw)
To: Srinivas Neeli, a.zummo, alexandre.belloni, robh+dt,
srinivas.neeli, neelisrinivas18, krzysztof.kozlowski+dt,
michal.simek, sgoud, shubhraj
Cc: devicetree, linux-rtc, linux-arm-kernel, linux-kernel, git, git,
Rob Herring
On 24/06/2022 14:02, Srinivas Neeli wrote:
> Added clock information and deprecated calibration support.
>
> Signed-off-by: Srinivas Neeli <srinivas.neeli@xilinx.com>
> Reviewed-by: Rob Herring <robh@kernel.org>
> ---
> Changes in V9:
> -Updated clock information in clock-names.
> Changes in V8:
> -None
> Changes in V7:
> -None
> Changes in V6:
> -Removed dtc warnings.
> Changes in V5:
> -Removed quotes and _clk suffix from clocknames.
> Changes in V4:
> - Deprecated calibrtion support
> Changes in V3:
> - New patch
> ---
> .../devicetree/bindings/rtc/xlnx,zynqmp-rtc.yaml | 12 +++++++++++-
> 1 file changed, 11 insertions(+), 1 deletion(-)
>
> diff --git a/Documentation/devicetree/bindings/rtc/xlnx,zynqmp-rtc.yaml b/Documentation/devicetree/bindings/rtc/xlnx,zynqmp-rtc.yaml
> index bdb72d3ddf2a..9dfe2cc5966a 100644
> --- a/Documentation/devicetree/bindings/rtc/xlnx,zynqmp-rtc.yaml
> +++ b/Documentation/devicetree/bindings/rtc/xlnx,zynqmp-rtc.yaml
> @@ -23,8 +23,15 @@ properties:
> reg:
> maxItems: 1
>
> + clocks:
> + maxItems: 1
> +
> + clock-names:
> + items:
> + - const: rtc
> +
> interrupts:
> - minItems: 2
> + maxItems: 2
>
> interrupt-names:
> items:
> @@ -39,6 +46,7 @@ properties:
> minimum: 0x1
> maximum: 0x1FFFFF
> default: 0x198233
> + deprecated: true
>
> required:
> - compatible
> @@ -61,5 +69,7 @@ examples:
> interrupts = <0 26 4>, <0 27 4>;
> interrupt-names = "alarm", "sec";
> calibration = <0x198233>;
> + clock-names = "rtc_clk";
> + clocks = <&rtc_clk>;
Please test your bindings with `make dt_binding_check` before sending.
Best regards,
Krzysztof
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 10+ messages in thread