[PATCH net-next v2 0/2] Introduce PHY mode 10G-QXGMII

[PATCH net-next v2 0/2] Introduce PHY mode 10G-QXGMII

[Luo Jie]

This patch series adds 10G-QXGMII mode for PHY driver. The patch
series is split from the QCA8084 PHY driver patch series below.
https://lore.kernel.org/all/20231215074005.26976-1-quic_luoj@quicinc.com/
 
Per Andrew Lunn’s advice, submitting this patch series for acceptance
as they already include the necessary 'Reviewed-by:' tags. This way,
they need not wait for QCA8084 series patches to conclude review.

Changes in v2:
	* remove PHY_INTERFACE_MODE_10G_QXGMII from workaround of
	  validation in the phylink_validate_phy. 10G_QXGMII will
	  be set into phy->possible_interfaces in its .config_init
	  method of PHY driver that supports it. 

Vladimir Oltean (2):
  net: phy: introduce core support for phy-mode = "10g-qxgmii"
  dt-bindings: net: ethernet-controller: add 10g-qxgmii mode

 .../devicetree/bindings/net/ethernet-controller.yaml     | 1 +
 Documentation/networking/phy.rst                         | 6 ++++++
 drivers/net/phy/phy-core.c                               | 1 +
 drivers/net/phy/phylink.c                                | 9 ++++++++-
 include/linux/phy.h                                      | 4 ++++
 include/linux/phylink.h                                  | 1 +
 6 files changed, 21 insertions(+), 1 deletion(-)


base-commit: 934c29999b57b835d65442da6f741d5e27f3b584
-- 
2.34.1

[PATCH net-next v2 1/2] net: phy: introduce core support for phy-mode = "10g-qxgmii"

[Luo Jie]

From: Vladimir Oltean <vladimir.oltean@nxp.com>

10G-QXGMII is a MAC-to-PHY interface defined by the USXGMII multiport
specification. It uses the same signaling as USXGMII, but it multiplexes
4 ports over the link, resulting in a maximum speed of 2.5G per port.

Some in-tree SoCs like the NXP LS1028A use "usxgmii" when they mean
either the single-port USXGMII or the quad-port 10G-QXGMII variant, and
they could get away just fine with that thus far. But there is a need to
distinguish between the 2 as far as SerDes drivers are concerned.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Luo Jie <quic_luoj@quicinc.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
---
 Documentation/networking/phy.rst | 6 ++++++
 drivers/net/phy/phy-core.c       | 1 +
 drivers/net/phy/phylink.c        | 9 ++++++++-
 include/linux/phy.h              | 4 ++++
 include/linux/phylink.h          | 1 +
 5 files changed, 20 insertions(+), 1 deletion(-)

diff --git a/Documentation/networking/phy.rst b/Documentation/networking/phy.rst
index 1283240d7620..f64641417c54 100644
--- a/Documentation/networking/phy.rst
+++ b/Documentation/networking/phy.rst
@@ -327,6 +327,12 @@ Some of the interface modes are described below:
     This is the Penta SGMII mode, it is similar to QSGMII but it combines 5
     SGMII lines into a single link compared to 4 on QSGMII.
 
+``PHY_INTERFACE_MODE_10G_QXGMII``
+    Represents the 10G-QXGMII PHY-MAC interface as defined by the Cisco USXGMII
+    Multiport Copper Interface document. It supports 4 ports over a 10.3125 GHz
+    SerDes lane, each port having speeds of 2.5G / 1G / 100M / 10M achieved
+    through symbol replication. The PCS expects the standard USXGMII code word.
+
 Pause frames / flow control
 ===========================
 
diff --git a/drivers/net/phy/phy-core.c b/drivers/net/phy/phy-core.c
index 15f349e5995a..a235ea2264a7 100644
--- a/drivers/net/phy/phy-core.c
+++ b/drivers/net/phy/phy-core.c
@@ -141,6 +141,7 @@ int phy_interface_num_ports(phy_interface_t interface)
 		return 1;
 	case PHY_INTERFACE_MODE_QSGMII:
 	case PHY_INTERFACE_MODE_QUSGMII:
+	case PHY_INTERFACE_MODE_10G_QXGMII:
 		return 4;
 	case PHY_INTERFACE_MODE_PSGMII:
 		return 5;
diff --git a/drivers/net/phy/phylink.c b/drivers/net/phy/phylink.c
index 02427378acfd..6c24c48dcf0f 100644
--- a/drivers/net/phy/phylink.c
+++ b/drivers/net/phy/phylink.c
@@ -231,6 +231,7 @@ static int phylink_interface_max_speed(phy_interface_t interface)
 		return SPEED_1000;
 
 	case PHY_INTERFACE_MODE_2500BASEX:
+	case PHY_INTERFACE_MODE_10G_QXGMII:
 		return SPEED_2500;
 
 	case PHY_INTERFACE_MODE_5GBASER:
@@ -500,7 +501,11 @@ static unsigned long phylink_get_capabilities(phy_interface_t interface,
 
 	switch (interface) {
 	case PHY_INTERFACE_MODE_USXGMII:
-		caps |= MAC_10000FD | MAC_5000FD | MAC_2500FD;
+		caps |= MAC_10000FD | MAC_5000FD;
+		fallthrough;
+
+	case PHY_INTERFACE_MODE_10G_QXGMII:
+		caps |= MAC_2500FD;
 		fallthrough;
 
 	case PHY_INTERFACE_MODE_RGMII_TXID:
@@ -926,6 +931,7 @@ static int phylink_parse_mode(struct phylink *pl,
 		case PHY_INTERFACE_MODE_5GBASER:
 		case PHY_INTERFACE_MODE_25GBASER:
 		case PHY_INTERFACE_MODE_USXGMII:
+		case PHY_INTERFACE_MODE_10G_QXGMII:
 		case PHY_INTERFACE_MODE_10GKR:
 		case PHY_INTERFACE_MODE_10GBASER:
 		case PHY_INTERFACE_MODE_XLGMII:
@@ -1124,6 +1130,7 @@ static unsigned int phylink_pcs_neg_mode(unsigned int mode,
 	case PHY_INTERFACE_MODE_QSGMII:
 	case PHY_INTERFACE_MODE_QUSGMII:
 	case PHY_INTERFACE_MODE_USXGMII:
+	case PHY_INTERFACE_MODE_10G_QXGMII:
 		/* These protocols are designed for use with a PHY which
 		 * communicates its negotiation result back to the MAC via
 		 * inband communication. Note: there exist PHYs that run
diff --git a/include/linux/phy.h b/include/linux/phy.h
index e6e83304558e..205fccfc0f60 100644
--- a/include/linux/phy.h
+++ b/include/linux/phy.h
@@ -128,6 +128,7 @@ extern const int phy_10gbit_features_array[1];
  * @PHY_INTERFACE_MODE_10GKR: 10GBASE-KR - with Clause 73 AN
  * @PHY_INTERFACE_MODE_QUSGMII: Quad Universal SGMII
  * @PHY_INTERFACE_MODE_1000BASEKX: 1000Base-KX - with Clause 73 AN
+ * @PHY_INTERFACE_MODE_10G_QXGMII: 10G-QXGMII - 4 ports over 10G USXGMII
  * @PHY_INTERFACE_MODE_MAX: Book keeping
  *
  * Describes the interface between the MAC and PHY.
@@ -168,6 +169,7 @@ typedef enum {
 	PHY_INTERFACE_MODE_10GKR,
 	PHY_INTERFACE_MODE_QUSGMII,
 	PHY_INTERFACE_MODE_1000BASEKX,
+	PHY_INTERFACE_MODE_10G_QXGMII,
 	PHY_INTERFACE_MODE_MAX,
 } phy_interface_t;
 
@@ -289,6 +291,8 @@ static inline const char *phy_modes(phy_interface_t interface)
 		return "100base-x";
 	case PHY_INTERFACE_MODE_QUSGMII:
 		return "qusgmii";
+	case PHY_INTERFACE_MODE_10G_QXGMII:
+		return "10g-qxgmii";
 	default:
 		return "unknown";
 	}
diff --git a/include/linux/phylink.h b/include/linux/phylink.h
index a30a692acc32..2381e07429a2 100644
--- a/include/linux/phylink.h
+++ b/include/linux/phylink.h
@@ -654,6 +654,7 @@ static inline int phylink_get_link_timer_ns(phy_interface_t interface)
 	case PHY_INTERFACE_MODE_SGMII:
 	case PHY_INTERFACE_MODE_QSGMII:
 	case PHY_INTERFACE_MODE_USXGMII:
+	case PHY_INTERFACE_MODE_10G_QXGMII:
 		return 1600000;
 
 	case PHY_INTERFACE_MODE_1000BASEX:
-- 
2.34.1

[PATCH net-next v2 2/2] dt-bindings: net: ethernet-controller: add 10g-qxgmii mode

[Luo Jie]

From: Vladimir Oltean <vladimir.oltean@nxp.com>

Add the new interface mode 10g-qxgmii, which is similar to
usxgmii but extend to 4 channels to support maximum of 4
ports with the link speed 10M/100M/1G/2.5G.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Luo Jie <quic_luoj@quicinc.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
---
 Documentation/devicetree/bindings/net/ethernet-controller.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/net/ethernet-controller.yaml b/Documentation/devicetree/bindings/net/ethernet-controller.yaml
index b2785b03139f..45819b235800 100644
--- a/Documentation/devicetree/bindings/net/ethernet-controller.yaml
+++ b/Documentation/devicetree/bindings/net/ethernet-controller.yaml
@@ -103,6 +103,7 @@ properties:
       - usxgmii
       - 10gbase-r
       - 25gbase-r
+      - 10g-qxgmii
 
   phy-mode:
     $ref: "#/properties/phy-connection-type"
-- 
2.34.1

Re: [PATCH net-next v2 0/2] Introduce PHY mode 10G-QXGMII

[patchwork-bot+netdevbpf]

Hello:

This series was applied to netdev/net-next.git (main)
by Paolo Abeni <pabeni@redhat.com>:

On Sat, 15 Jun 2024 20:00:26 +0800 you wrote:
> This patch series adds 10G-QXGMII mode for PHY driver. The patch
> series is split from the QCA8084 PHY driver patch series below.
> https://lore.kernel.org/all/20231215074005.26976-1-quic_luoj@quicinc.com/
> 
> Per Andrew Lunn’s advice, submitting this patch series for acceptance
> as they already include the necessary 'Reviewed-by:' tags. This way,
> they need not wait for QCA8084 series patches to conclude review.
> 
> [...]

Here is the summary with links:
  - [net-next,v2,1/2] net: phy: introduce core support for phy-mode = "10g-qxgmii"
    https://git.kernel.org/netdev/net-next/c/777b8afb8179
  - [net-next,v2,2/2] dt-bindings: net: ethernet-controller: add 10g-qxgmii mode
    https://git.kernel.org/netdev/net-next/c/5dfabcdd76b1

You are awesome, thank you!
-- 
Deet-doot-dot, I am a bot.
https://korg.docs.kernel.org/patchwork/pwbot.html