[PATCH V4 0/3] Add SD Card support for sm8750 SoC and boards

[PATCH V4 0/3] Add SD Card support for sm8750 SoC and boards

[Sarthak Garg]

Add SD Card support for sm8750 SoC, including MTP and QRD boards.

- Changed from v3
    - As suggested by Krzysztof Kozlowski refactor the code to follow
      DTS coding style and use hex everywhere in reg.

- Changed from v2
    - As suggested by Abel Vesa move the GPIO configuration for SD card
      detection (specifically the pin settings for gpio55) from the
      SoC-level device tree (sm8750.dtsi) to the board-specific device
      tree files.

- Changed from v1
    - As suggested by Konrad Dybcio the patch into separate commits per
      board and did formatting improvements (e.g. aligning < symbols,
      placing each item on a new line).
    - Addressed Konrad Dybcio comment to use SVS_L1 for opp-202000000.

Sarthak Garg (3):
  arm64: dts: qcom: sm8750: Add SDC2 nodes for sm8750 soc
  arm64: dts: qcom: sm8750-mtp: Add SDC2 node for sm8750 mtp board
  arm64: dts: qcom: sm8750-qrd: Add SDC2 node for sm8750 qrd board

 arch/arm64/boot/dts/qcom/sm8750-mtp.dts | 23 +++++++++++
 arch/arm64/boot/dts/qcom/sm8750-qrd.dts | 23 +++++++++++
 arch/arm64/boot/dts/qcom/sm8750.dtsi    | 54 +++++++++++++++++++++++++
 3 files changed, 100 insertions(+)

-- 
2.34.1

[PATCH V4 1/3] arm64: dts: qcom: sm8750: Add SDC2 nodes for sm8750 soc

[Sarthak Garg]

Add SD Card host controller for sm8750 soc.

Signed-off-by: Sarthak Garg <sarthak.garg@oss.qualcomm.com>
---
 arch/arm64/boot/dts/qcom/sm8750.dtsi | 54 ++++++++++++++++++++++++++++
 1 file changed, 54 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm8750.dtsi b/arch/arm64/boot/dts/qcom/sm8750.dtsi
index a82d9867c7cb..95b210fbfead 100644
--- a/arch/arm64/boot/dts/qcom/sm8750.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8750.dtsi
@@ -3482,6 +3482,60 @@ pcie0_phy: phy@1c06000 {
 			status = "disabled";
 		};
 
+		sdhc_2: mmc@8804000 {
+			compatible = "qcom,sm8750-sdhci", "qcom,sdhci-msm-v5";
+			reg = <0x0 0x08804000 0x0 0x1000>;
+
+			interrupts = <GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 223 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hc_irq",
+					  "pwr_irq";
+
+			clocks = <&gcc GCC_SDCC2_AHB_CLK>,
+				 <&gcc GCC_SDCC2_APPS_CLK>,
+				 <&rpmhcc RPMH_CXO_CLK>;
+			clock-names = "iface",
+				      "core",
+				      "xo";
+
+			interconnects = <&aggre2_noc MASTER_SDCC_2 QCOM_ICC_TAG_ALWAYS
+					&mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>,
+					<&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ACTIVE_ONLY
+					&config_noc SLAVE_SDCC_2 QCOM_ICC_TAG_ACTIVE_ONLY>;
+			interconnect-names = "sdhc-ddr",
+					     "cpu-sdhc";
+
+			power-domains = <&rpmhpd RPMHPD_CX>;
+			operating-points-v2 = <&sdhc2_opp_table>;
+
+			qcom,dll-config = <0x0007442c>;
+			qcom,ddr-config = <0x80040868>;
+
+			iommus = <&apps_smmu 0x540 0x0>;
+			dma-coherent;
+
+			bus-width = <4>;
+			max-sd-hs-hz = <37500000>;
+
+			resets = <&gcc GCC_SDCC2_BCR>;
+
+			status = "disabled";
+
+			sdhc2_opp_table: opp-table {
+				compatible = "operating-points-v2";
+
+				opp-100000000 {
+					opp-hz = /bits/ 64 <100000000>;
+					required-opps = <&rpmhpd_opp_low_svs>;
+				};
+
+				opp-202000000 {
+					opp-hz = /bits/ 64 <202000000>;
+					required-opps = <&rpmhpd_opp_svs_l1>;
+				};
+			};
+		};
+
 		ufs_mem_phy: phy@1d80000 {
 			compatible = "qcom,sm8750-qmp-ufs-phy";
 			reg = <0x0 0x01d80000 0x0 0x2000>;
-- 
2.34.1

Re: [PATCH V4 1/3] arm64: dts: qcom: sm8750: Add SDC2 nodes for sm8750 soc

[Krzysztof Kozlowski]

On 10/11/2025 09:50, Sarthak Garg wrote:
> Add SD Card host controller for sm8750 soc.
> 
> Signed-off-by: Sarthak Garg <sarthak.garg@oss.qualcomm.com>
> ---
>  arch/arm64/boot/dts/qcom/sm8750.dtsi | 54 ++++++++++++++++++++++++++++
>  1 file changed, 54 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/qcom/sm8750.dtsi b/arch/arm64/boot/dts/qcom/sm8750.dtsi
> index a82d9867c7cb..95b210fbfead 100644
> --- a/arch/arm64/boot/dts/qcom/sm8750.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sm8750.dtsi
> @@ -3482,6 +3482,60 @@ pcie0_phy: phy@1c06000 {
>  			status = "disabled";
>  		};
>  
> +		sdhc_2: mmc@8804000 {

Nothing improved.

Best regards,
Krzysztof

Re: [PATCH V4 1/3] arm64: dts: qcom: sm8750: Add SDC2 nodes for sm8750 soc

[Sarthak Garg]

On 11/10/2025 2:43 PM, Krzysztof Kozlowski wrote:
> On 10/11/2025 09:50, Sarthak Garg wrote:
>> Add SD Card host controller for sm8750 soc.
>>
>> Signed-off-by: Sarthak Garg <sarthak.garg@oss.qualcomm.com>
>> ---
>>   arch/arm64/boot/dts/qcom/sm8750.dtsi | 54 ++++++++++++++++++++++++++++
>>   1 file changed, 54 insertions(+)
>>
>> diff --git a/arch/arm64/boot/dts/qcom/sm8750.dtsi b/arch/arm64/boot/dts/qcom/sm8750.dtsi
>> index a82d9867c7cb..95b210fbfead 100644
>> --- a/arch/arm64/boot/dts/qcom/sm8750.dtsi
>> +++ b/arch/arm64/boot/dts/qcom/sm8750.dtsi
>> @@ -3482,6 +3482,60 @@ pcie0_phy: phy@1c06000 {
>>   			status = "disabled";
>>   		};
>>   
>> +		sdhc_2: mmc@8804000 {
> Nothing improved.
>
> Best regards,
> Krzysztof


I moved the sdhc_2 node to follow alphanumeric ordering and used hex in reg.
What extra is needed ?


Regards,
Sarthak

Re: [PATCH V4 1/3] arm64: dts: qcom: sm8750: Add SDC2 nodes for sm8750 soc

[Konrad Dybcio]

On 11/10/25 10:25 AM, Sarthak Garg wrote:
> 
> On 11/10/2025 2:43 PM, Krzysztof Kozlowski wrote:
>> On 10/11/2025 09:50, Sarthak Garg wrote:
>>> Add SD Card host controller for sm8750 soc.
>>>
>>> Signed-off-by: Sarthak Garg <sarthak.garg@oss.qualcomm.com>
>>> ---
>>>   arch/arm64/boot/dts/qcom/sm8750.dtsi | 54 ++++++++++++++++++++++++++++
>>>   1 file changed, 54 insertions(+)
>>>
>>> diff --git a/arch/arm64/boot/dts/qcom/sm8750.dtsi b/arch/arm64/boot/dts/qcom/sm8750.dtsi
>>> index a82d9867c7cb..95b210fbfead 100644
>>> --- a/arch/arm64/boot/dts/qcom/sm8750.dtsi
>>> +++ b/arch/arm64/boot/dts/qcom/sm8750.dtsi
>>> @@ -3482,6 +3482,60 @@ pcie0_phy: phy@1c06000 {
>>>               status = "disabled";
>>>           };
>>>   +        sdhc_2: mmc@8804000 {
>> Nothing improved.
>>
>> Best regards,
>> Krzysztof
> 
> 
> I moved the sdhc_2 node to follow alphanumeric ordering and used hex in reg.
> What extra is needed ?

Nodes with a unit address (numbers after @) are supposed to be sorted
by that register, just like any other register map

Konrad

Re: [PATCH V4 1/3] arm64: dts: qcom: sm8750: Add SDC2 nodes for sm8750 soc

[Sarthak Garg]

On 11/10/2025 4:38 PM, Konrad Dybcio wrote:
> On 11/10/25 10:25 AM, Sarthak Garg wrote:
>> On 11/10/2025 2:43 PM, Krzysztof Kozlowski wrote:
>>> On 10/11/2025 09:50, Sarthak Garg wrote:
>>>> Add SD Card host controller for sm8750 soc.
>>>>
>>>> Signed-off-by: Sarthak Garg <sarthak.garg@oss.qualcomm.com>
>>>> ---
>>>>    arch/arm64/boot/dts/qcom/sm8750.dtsi | 54 ++++++++++++++++++++++++++++
>>>>    1 file changed, 54 insertions(+)
>>>>
>>>> diff --git a/arch/arm64/boot/dts/qcom/sm8750.dtsi b/arch/arm64/boot/dts/qcom/sm8750.dtsi
>>>> index a82d9867c7cb..95b210fbfead 100644
>>>> --- a/arch/arm64/boot/dts/qcom/sm8750.dtsi
>>>> +++ b/arch/arm64/boot/dts/qcom/sm8750.dtsi
>>>> @@ -3482,6 +3482,60 @@ pcie0_phy: phy@1c06000 {
>>>>                status = "disabled";
>>>>            };
>>>>    +        sdhc_2: mmc@8804000 {
>>> Nothing improved.
>>>
>>> Best regards,
>>> Krzysztof
>>
>> I moved the sdhc_2 node to follow alphanumeric ordering and used hex in reg.
>> What extra is needed ?
> Nodes with a unit address (numbers after @) are supposed to be sorted
> by that register, just like any other register map
>
> Konrad


Thanks for pointing out. Will update in V5.


Regards,
Sarthak

[PATCH V4 2/3] arm64: dts: qcom: sm8750-mtp: Add SDC2 node for sm8750 mtp board

[Sarthak Garg]

Enable SD Card host controller for sm8750 mtp board.

Signed-off-by: Sarthak Garg <sarthak.garg@oss.qualcomm.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
---
 arch/arm64/boot/dts/qcom/sm8750-mtp.dts | 23 +++++++++++++++++++++++
 1 file changed, 23 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm8750-mtp.dts b/arch/arm64/boot/dts/qcom/sm8750-mtp.dts
index 3bbb53b7c71f..3b87a1af3333 100644
--- a/arch/arm64/boot/dts/qcom/sm8750-mtp.dts
+++ b/arch/arm64/boot/dts/qcom/sm8750-mtp.dts
@@ -1030,6 +1030,22 @@ &remoteproc_mpss {
 	status = "fail";
 };
 
+&sdhc_2 {
+	cd-gpios = <&tlmm 55 GPIO_ACTIVE_LOW>;
+
+	vmmc-supply = <&vreg_l9b_2p9>;
+	vqmmc-supply = <&vreg_l8b_1p8>;
+
+	no-sdio;
+	no-mmc;
+
+	pinctrl-0 = <&sdc2_default &sdc2_card_det_n>;
+	pinctrl-1 = <&sdc2_sleep &sdc2_card_det_n>;
+	pinctrl-names = "default", "sleep";
+
+	status = "okay";
+};
+
 &swr0 {
 	status = "okay";
 
@@ -1163,6 +1179,13 @@ wlan_en: wlan-en-state {
 		drive-strength = <8>;
 		bias-pull-down;
 	};
+
+	sdc2_card_det_n: sd-card-det-n-state {
+		pins = "gpio55";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-up;
+	};
 };
 
 &uart14 {
-- 
2.34.1

[PATCH V4 3/3] arm64: dts: qcom: sm8750-qrd: Add SDC2 node for sm8750 qrd board

[Sarthak Garg]

Enable SD Card host controller for sm8750 qrd board.

Signed-off-by: Sarthak Garg <sarthak.garg@oss.qualcomm.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
---
 arch/arm64/boot/dts/qcom/sm8750-qrd.dts | 23 +++++++++++++++++++++++
 1 file changed, 23 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm8750-qrd.dts b/arch/arm64/boot/dts/qcom/sm8750-qrd.dts
index 13c7b9664c89..e08bebf93966 100644
--- a/arch/arm64/boot/dts/qcom/sm8750-qrd.dts
+++ b/arch/arm64/boot/dts/qcom/sm8750-qrd.dts
@@ -916,6 +916,22 @@ &remoteproc_mpss {
 	status = "okay";
 };
 
+&sdhc_2 {
+	cd-gpios = <&tlmm 55 GPIO_ACTIVE_LOW>;
+
+	vmmc-supply = <&vreg_l9b_2p9>;
+	vqmmc-supply = <&vreg_l8b_1p8>;
+
+	no-sdio;
+	no-mmc;
+
+	pinctrl-0 = <&sdc2_default &sdc2_card_det_n>;
+	pinctrl-1 = <&sdc2_sleep &sdc2_card_det_n>;
+	pinctrl-names = "default", "sleep";
+
+	status = "okay";
+};
+
 &swr0 {
 	status = "okay";
 
@@ -1031,6 +1047,13 @@ wcd_default: wcd-reset-n-active-state {
 		bias-disable;
 		output-low;
 	};
+
+	sdc2_card_det_n: sd-card-det-n-state {
+		pins = "gpio55";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-up;
+	};
 };
 
 &uart7 {
-- 
2.34.1

Re: [PATCH V4 0/3] Add SD Card support for sm8750 SoC and boards

[Rob Herring (Arm)]

On Mon, 10 Nov 2025 14:20:10 +0530, Sarthak Garg wrote:
> Add SD Card support for sm8750 SoC, including MTP and QRD boards.
> 
> - Changed from v3
>     - As suggested by Krzysztof Kozlowski refactor the code to follow
>       DTS coding style and use hex everywhere in reg.
> 
> - Changed from v2
>     - As suggested by Abel Vesa move the GPIO configuration for SD card
>       detection (specifically the pin settings for gpio55) from the
>       SoC-level device tree (sm8750.dtsi) to the board-specific device
>       tree files.
> 
> - Changed from v1
>     - As suggested by Konrad Dybcio the patch into separate commits per
>       board and did formatting improvements (e.g. aligning < symbols,
>       placing each item on a new line).
>     - Addressed Konrad Dybcio comment to use SVS_L1 for opp-202000000.
> 
> Sarthak Garg (3):
>   arm64: dts: qcom: sm8750: Add SDC2 nodes for sm8750 soc
>   arm64: dts: qcom: sm8750-mtp: Add SDC2 node for sm8750 mtp board
>   arm64: dts: qcom: sm8750-qrd: Add SDC2 node for sm8750 qrd board
> 
>  arch/arm64/boot/dts/qcom/sm8750-mtp.dts | 23 +++++++++++
>  arch/arm64/boot/dts/qcom/sm8750-qrd.dts | 23 +++++++++++
>  arch/arm64/boot/dts/qcom/sm8750.dtsi    | 54 +++++++++++++++++++++++++
>  3 files changed, 100 insertions(+)
> 
> --
> 2.34.1
> 
> 
> 


My bot found new DTB warnings on the .dts files added or changed in this
series.

Some warnings may be from an existing SoC .dtsi. Or perhaps the warnings
are fixed by another series. Ultimately, it is up to the platform
maintainer whether these warnings are acceptable or not. No need to reply
unless the platform maintainer has comments.

If you already ran DT checks and didn't see these error(s), then
make sure dt-schema is up to date:

  pip3 install dtschema --upgrade


This patch series was applied (using b4) to base:
 Base: attempting to guess base-commit...
 Base: tags/v6.18-rc1-53-gc2703c90161b (exact match)
 Base: tags/v6.18-rc1-53-gc2703c90161b (use --merge-base to override)

If this is not the correct base, please add 'base-commit' tag
(or use b4 which does this automatically)

New warnings running 'make CHECK_DTBS=y for arch/arm64/boot/dts/qcom/' for 20251110085013.802976-1-sarthak.garg@oss.qualcomm.com:

arch/arm64/boot/dts/qcom/sm8750-mtp.dtb: mmc@8804000 (qcom,sm8750-sdhci): compatible: 'oneOf' conditional failed, one must be fixed:
	['qcom,sm8750-sdhci', 'qcom,sdhci-msm-v5'] is too long
	'qcom,sm8750-sdhci' is not one of ['qcom,sdhci-msm-v4']
	'qcom,sm8750-sdhci' is not one of ['qcom,apq8084-sdhci', 'qcom,ipq4019-sdhci', 'qcom,ipq8074-sdhci', 'qcom,msm8226-sdhci', 'qcom,msm8953-sdhci', 'qcom,msm8974-sdhci', 'qcom,msm8976-sdhci', 'qcom,msm8916-sdhci', 'qcom,msm8992-sdhci', 'qcom,msm8994-sdhci', 'qcom,msm8996-sdhci', 'qcom,msm8998-sdhci']
	'qcom,sm8750-sdhci' is not one of ['qcom,ipq5018-sdhci', 'qcom,ipq5332-sdhci', 'qcom,ipq5424-sdhci', 'qcom,ipq6018-sdhci', 'qcom,ipq9574-sdhci', 'qcom,milos-sdhci', 'qcom,qcm2290-sdhci', 'qcom,qcs404-sdhci', 'qcom,qcs615-sdhci', 'qcom,qcs8300-sdhci', 'qcom,qdu1000-sdhci', 'qcom,sa8775p-sdhci', 'qcom,sar2130p-sdhci', 'qcom,sc7180-sdhci', 'qcom,sc7280-sdhci', 'qcom,sc8280xp-sdhci', 'qcom,sdm630-sdhci', 'qcom,sdm670-sdhci', 'qcom,sdm845-sdhci', 'qcom,sdx55-sdhci', 'qcom,sdx65-sdhci', 'qcom,sdx75-sdhci', 'qcom,sm6115-sdhci', 'qcom,sm6125-sdhci', 'qcom,sm6350-sdhci', 'qcom,sm6375-sdhci', 'qcom,sm7150-sdhci', 'qcom,sm8150-sdhci', 'qcom,sm8250-sdhci', 'qcom,sm8350-sdhci', 'qcom,sm8450-sdhci', 'qcom,sm8550-sdhci', 'qcom,sm8650-sdhci', 'qcom,x1e80100-sdhci']
	'qcom,sdhci-msm-v4' was expected
	from schema $id: http://devicetree.org/schemas/mmc/sdhci-msm.yaml
arch/arm64/boot/dts/qcom/sm8750-mtp.dtb: /soc@0/mmc@8804000: failed to match any schema with compatible: ['qcom,sm8750-sdhci', 'qcom,sdhci-msm-v5']
arch/arm64/boot/dts/qcom/sm8750-qrd.dtb: mmc@8804000 (qcom,sm8750-sdhci): compatible: 'oneOf' conditional failed, one must be fixed:
	['qcom,sm8750-sdhci', 'qcom,sdhci-msm-v5'] is too long
	'qcom,sm8750-sdhci' is not one of ['qcom,sdhci-msm-v4']
	'qcom,sm8750-sdhci' is not one of ['qcom,apq8084-sdhci', 'qcom,ipq4019-sdhci', 'qcom,ipq8074-sdhci', 'qcom,msm8226-sdhci', 'qcom,msm8953-sdhci', 'qcom,msm8974-sdhci', 'qcom,msm8976-sdhci', 'qcom,msm8916-sdhci', 'qcom,msm8992-sdhci', 'qcom,msm8994-sdhci', 'qcom,msm8996-sdhci', 'qcom,msm8998-sdhci']
	'qcom,sm8750-sdhci' is not one of ['qcom,ipq5018-sdhci', 'qcom,ipq5332-sdhci', 'qcom,ipq5424-sdhci', 'qcom,ipq6018-sdhci', 'qcom,ipq9574-sdhci', 'qcom,milos-sdhci', 'qcom,qcm2290-sdhci', 'qcom,qcs404-sdhci', 'qcom,qcs615-sdhci', 'qcom,qcs8300-sdhci', 'qcom,qdu1000-sdhci', 'qcom,sa8775p-sdhci', 'qcom,sar2130p-sdhci', 'qcom,sc7180-sdhci', 'qcom,sc7280-sdhci', 'qcom,sc8280xp-sdhci', 'qcom,sdm630-sdhci', 'qcom,sdm670-sdhci', 'qcom,sdm845-sdhci', 'qcom,sdx55-sdhci', 'qcom,sdx65-sdhci', 'qcom,sdx75-sdhci', 'qcom,sm6115-sdhci', 'qcom,sm6125-sdhci', 'qcom,sm6350-sdhci', 'qcom,sm6375-sdhci', 'qcom,sm7150-sdhci', 'qcom,sm8150-sdhci', 'qcom,sm8250-sdhci', 'qcom,sm8350-sdhci', 'qcom,sm8450-sdhci', 'qcom,sm8550-sdhci', 'qcom,sm8650-sdhci', 'qcom,x1e80100-sdhci']
	'qcom,sdhci-msm-v4' was expected
	from schema $id: http://devicetree.org/schemas/mmc/sdhci-msm.yaml
arch/arm64/boot/dts/qcom/sm8750-qrd.dtb: /soc@0/mmc@8804000: failed to match any schema with compatible: ['qcom,sm8750-sdhci', 'qcom,sdhci-msm-v5']