From: laurent.pinchart@ideasonboard.com (Laurent Pinchart)
To: linus-amlogic@lists.infradead.org
Subject: [PATCH 2/4] ARM64: dts: meson-gx: Add Graphic Controller nodes
Date: Tue, 29 Nov 2016 21:16:17 +0200 [thread overview]
Message-ID: <1812737.pZP73QSyU1@avalon> (raw)
In-Reply-To: <1480416469-9655-3-git-send-email-narmstrong@baylibre.com>
Hi Neil,
Thank you for the patch.
On Tuesday 29 Nov 2016 11:47:47 Neil Armstrong wrote:
> Add Video Processing Unit and CVBS Output nodes, and enable CVBS on selected
> boards.
>
> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
> ---
> arch/arm64/boot/dts/amlogic/meson-gx.dtsi | 46 +++++++++++++++++++
> .../boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts | 4 ++
> arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi | 4 ++
> arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi | 8 ++++
> .../boot/dts/amlogic/meson-gxl-nexbox-a95x.dts | 4 ++
> arch/arm64/boot/dts/amlogic/meson-gxl.dtsi | 8 ++++
> .../arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts | 4 ++
> arch/arm64/boot/dts/amlogic/meson-gxm.dtsi | 8 ++++
> 8 files changed, 86 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/amlogic/meson-gx.dtsi
> b/arch/arm64/boot/dts/amlogic/meson-gx.dtsi index fc033c0..644d5f6 100644
> --- a/arch/arm64/boot/dts/amlogic/meson-gx.dtsi
> +++ b/arch/arm64/boot/dts/amlogic/meson-gx.dtsi
> @@ -153,6 +153,27 @@
> };
> };
>
> + venc_cvbs: venc-cvbs {
> + compatible = "amlogic,meson-gx-cvbs";
> + status = "disabled";
Still no registers here ?
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + venc_cvbs_in: port at 0 {
Nitpicking, you don't need a label here as ports are never referenced by
phandle. Same for the vpu node below.
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0>;
> +
> + venc_cvbs_in_vpu: endpoint at 0 {
> + reg = <0>;
And there's no requirement to number the endpoint if there's a single one of
them (but it's not forbidden either).
> + remote-endpoint =
<&vpu_out_venc_cvbs>;
> + };
> + };
> + };
> + };
> +
> soc {
> compatible = "simple-bus";
> #address-cells = <2>;
> @@ -356,5 +377,30 @@
> status = "disabled";
> };
> };
> +
> + vpu: vpu at d0100000 {
> + compatible = "amlogic,meson-gx-vpu";
> + reg = <0x0 0xd0100000 0x0 0x100000>,
> + <0x0 0xc883c000 0x0 0x1000>,
> + <0x0 0xc8838000 0x0 0x1000>;
> + reg-names = "base", "hhi", "dmc";
> + interrupts = <GIC_SPI 3 IRQ_TYPE_EDGE_RISING>;
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + vpu_out: port at 1 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <1>;
> +
> + vpu_out_venc_cvbs: endpoint at 0 {
> + reg = <0>;
> + remote-endpoint =
<&venc_cvbs_in_vpu>;
> + };
> + };
> + };
> + };
> };
> };
> diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts
> b/arch/arm64/boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts index
> 9696820..a55d1cf 100644
> --- a/arch/arm64/boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts
> +++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts
> @@ -229,3 +229,7 @@
> clocks = <&clkc CLKID_FCLK_DIV4>;
> clock-names = "clkin0";
> };
> +
> +&venc_cvbs {
> + status = "okay";
> +};
> diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi
> b/arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi index 5e5e2de..3c09bd1
> 100644
> --- a/arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi
> +++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi
> @@ -266,3 +266,7 @@
> clocks = <&clkc CLKID_FCLK_DIV4>;
> clock-names = "clkin0";
> };
> +
> +&venc_cvbs {
> + status = "okay";
> +};
> diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi
> b/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi index ac5ad3b..1a321c8f
> 100644
> --- a/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi
> +++ b/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi
> @@ -506,3 +506,11 @@
> <&clkc CLKID_FCLK_DIV2>;
> clock-names = "core", "clkin0", "clkin1";
> };
> +
> +&venc_cvbs {
> + compatible = "amlogic,meson-gxbb-cvbs", "amlogic,meson-gx-cvbs";
> +};
> +
> +&vpu {
> + compatible = "amlogic,meson-gxbb-vpu", "amlogic,meson-gx-vpu";
> +};
> diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-nexbox-a95x.dts
> b/arch/arm64/boot/dts/amlogic/meson-gxl-nexbox-a95x.dts index
> e99101a..2a9b46f 100644
> --- a/arch/arm64/boot/dts/amlogic/meson-gxl-nexbox-a95x.dts
> +++ b/arch/arm64/boot/dts/amlogic/meson-gxl-nexbox-a95x.dts
> @@ -203,3 +203,7 @@
> clocks = <&clkc CLKID_FCLK_DIV4>;
> clock-names = "clkin0";
> };
> +
> +&venc_cvbs {
> + status = "okay";
> +};
> diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl.dtsi
> b/arch/arm64/boot/dts/amlogic/meson-gxl.dtsi index 3af54dc..b60c5ce 100644
> --- a/arch/arm64/boot/dts/amlogic/meson-gxl.dtsi
> +++ b/arch/arm64/boot/dts/amlogic/meson-gxl.dtsi
> @@ -299,3 +299,11 @@
> <&clkc CLKID_FCLK_DIV2>;
> clock-names = "core", "clkin0", "clkin1";
> };
> +
> +&venc_cvbs {
> + compatible = "amlogic,meson-gxl-cvbs", "amlogic,meson-gx-cvbs";
> +};
> +
> +&vpu {
> + compatible = "amlogic,meson-gxl-vpu", "amlogic,meson-gx-vpu";
> +};
> diff --git a/arch/arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts
> b/arch/arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts index
> d320727..1ae2451 100644
> --- a/arch/arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts
> +++ b/arch/arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts
> @@ -167,3 +167,7 @@
> max-speed = <1000>;
> };
> };
> +
> +&venc_cvbs {
> + status = "okay";
> +};
> diff --git a/arch/arm64/boot/dts/amlogic/meson-gxm.dtsi
> b/arch/arm64/boot/dts/amlogic/meson-gxm.dtsi index c1974bb..fecd8c2 100644
> --- a/arch/arm64/boot/dts/amlogic/meson-gxm.dtsi
> +++ b/arch/arm64/boot/dts/amlogic/meson-gxm.dtsi
> @@ -112,3 +112,11 @@
> };
> };
> };
> +
> +&venc_cvbs {
> + compatible = "amlogic,meson-gxm-cvbs", "amlogic,meson-gx-cvbs";
> +};
> +
> +&vpu {
> + compatible = "amlogic,meson-gxm-vpu", "amlogic,meson-gx-vpu";
> +};
--
Regards,
Laurent Pinchart
WARNING: multiple messages have this Message-ID (diff)
From: laurent.pinchart@ideasonboard.com (Laurent Pinchart)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH 2/4] ARM64: dts: meson-gx: Add Graphic Controller nodes
Date: Tue, 29 Nov 2016 21:16:17 +0200 [thread overview]
Message-ID: <1812737.pZP73QSyU1@avalon> (raw)
In-Reply-To: <1480416469-9655-3-git-send-email-narmstrong@baylibre.com>
Hi Neil,
Thank you for the patch.
On Tuesday 29 Nov 2016 11:47:47 Neil Armstrong wrote:
> Add Video Processing Unit and CVBS Output nodes, and enable CVBS on selected
> boards.
>
> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
> ---
> arch/arm64/boot/dts/amlogic/meson-gx.dtsi | 46 +++++++++++++++++++
> .../boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts | 4 ++
> arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi | 4 ++
> arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi | 8 ++++
> .../boot/dts/amlogic/meson-gxl-nexbox-a95x.dts | 4 ++
> arch/arm64/boot/dts/amlogic/meson-gxl.dtsi | 8 ++++
> .../arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts | 4 ++
> arch/arm64/boot/dts/amlogic/meson-gxm.dtsi | 8 ++++
> 8 files changed, 86 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/amlogic/meson-gx.dtsi
> b/arch/arm64/boot/dts/amlogic/meson-gx.dtsi index fc033c0..644d5f6 100644
> --- a/arch/arm64/boot/dts/amlogic/meson-gx.dtsi
> +++ b/arch/arm64/boot/dts/amlogic/meson-gx.dtsi
> @@ -153,6 +153,27 @@
> };
> };
>
> + venc_cvbs: venc-cvbs {
> + compatible = "amlogic,meson-gx-cvbs";
> + status = "disabled";
Still no registers here ?
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + venc_cvbs_in: port at 0 {
Nitpicking, you don't need a label here as ports are never referenced by
phandle. Same for the vpu node below.
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0>;
> +
> + venc_cvbs_in_vpu: endpoint at 0 {
> + reg = <0>;
And there's no requirement to number the endpoint if there's a single one of
them (but it's not forbidden either).
> + remote-endpoint =
<&vpu_out_venc_cvbs>;
> + };
> + };
> + };
> + };
> +
> soc {
> compatible = "simple-bus";
> #address-cells = <2>;
> @@ -356,5 +377,30 @@
> status = "disabled";
> };
> };
> +
> + vpu: vpu at d0100000 {
> + compatible = "amlogic,meson-gx-vpu";
> + reg = <0x0 0xd0100000 0x0 0x100000>,
> + <0x0 0xc883c000 0x0 0x1000>,
> + <0x0 0xc8838000 0x0 0x1000>;
> + reg-names = "base", "hhi", "dmc";
> + interrupts = <GIC_SPI 3 IRQ_TYPE_EDGE_RISING>;
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + vpu_out: port at 1 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <1>;
> +
> + vpu_out_venc_cvbs: endpoint at 0 {
> + reg = <0>;
> + remote-endpoint =
<&venc_cvbs_in_vpu>;
> + };
> + };
> + };
> + };
> };
> };
> diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts
> b/arch/arm64/boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts index
> 9696820..a55d1cf 100644
> --- a/arch/arm64/boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts
> +++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts
> @@ -229,3 +229,7 @@
> clocks = <&clkc CLKID_FCLK_DIV4>;
> clock-names = "clkin0";
> };
> +
> +&venc_cvbs {
> + status = "okay";
> +};
> diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi
> b/arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi index 5e5e2de..3c09bd1
> 100644
> --- a/arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi
> +++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi
> @@ -266,3 +266,7 @@
> clocks = <&clkc CLKID_FCLK_DIV4>;
> clock-names = "clkin0";
> };
> +
> +&venc_cvbs {
> + status = "okay";
> +};
> diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi
> b/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi index ac5ad3b..1a321c8f
> 100644
> --- a/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi
> +++ b/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi
> @@ -506,3 +506,11 @@
> <&clkc CLKID_FCLK_DIV2>;
> clock-names = "core", "clkin0", "clkin1";
> };
> +
> +&venc_cvbs {
> + compatible = "amlogic,meson-gxbb-cvbs", "amlogic,meson-gx-cvbs";
> +};
> +
> +&vpu {
> + compatible = "amlogic,meson-gxbb-vpu", "amlogic,meson-gx-vpu";
> +};
> diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-nexbox-a95x.dts
> b/arch/arm64/boot/dts/amlogic/meson-gxl-nexbox-a95x.dts index
> e99101a..2a9b46f 100644
> --- a/arch/arm64/boot/dts/amlogic/meson-gxl-nexbox-a95x.dts
> +++ b/arch/arm64/boot/dts/amlogic/meson-gxl-nexbox-a95x.dts
> @@ -203,3 +203,7 @@
> clocks = <&clkc CLKID_FCLK_DIV4>;
> clock-names = "clkin0";
> };
> +
> +&venc_cvbs {
> + status = "okay";
> +};
> diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl.dtsi
> b/arch/arm64/boot/dts/amlogic/meson-gxl.dtsi index 3af54dc..b60c5ce 100644
> --- a/arch/arm64/boot/dts/amlogic/meson-gxl.dtsi
> +++ b/arch/arm64/boot/dts/amlogic/meson-gxl.dtsi
> @@ -299,3 +299,11 @@
> <&clkc CLKID_FCLK_DIV2>;
> clock-names = "core", "clkin0", "clkin1";
> };
> +
> +&venc_cvbs {
> + compatible = "amlogic,meson-gxl-cvbs", "amlogic,meson-gx-cvbs";
> +};
> +
> +&vpu {
> + compatible = "amlogic,meson-gxl-vpu", "amlogic,meson-gx-vpu";
> +};
> diff --git a/arch/arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts
> b/arch/arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts index
> d320727..1ae2451 100644
> --- a/arch/arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts
> +++ b/arch/arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts
> @@ -167,3 +167,7 @@
> max-speed = <1000>;
> };
> };
> +
> +&venc_cvbs {
> + status = "okay";
> +};
> diff --git a/arch/arm64/boot/dts/amlogic/meson-gxm.dtsi
> b/arch/arm64/boot/dts/amlogic/meson-gxm.dtsi index c1974bb..fecd8c2 100644
> --- a/arch/arm64/boot/dts/amlogic/meson-gxm.dtsi
> +++ b/arch/arm64/boot/dts/amlogic/meson-gxm.dtsi
> @@ -112,3 +112,11 @@
> };
> };
> };
> +
> +&venc_cvbs {
> + compatible = "amlogic,meson-gxm-cvbs", "amlogic,meson-gx-cvbs";
> +};
> +
> +&vpu {
> + compatible = "amlogic,meson-gxm-vpu", "amlogic,meson-gx-vpu";
> +};
--
Regards,
Laurent Pinchart
WARNING: multiple messages have this Message-ID (diff)
From: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
To: Neil Armstrong <narmstrong@baylibre.com>
Cc: devicetree@vger.kernel.org, Xing.Xu@amlogic.com,
victor.wan@amlogic.com, khilman@baylibre.com,
linux-kernel@vger.kernel.org, dri-devel@lists.freedesktop.org,
jerry.cao@amlogic.com, carlo@caione.org,
linux-amlogic@lists.infradead.org,
linux-arm-kernel@lists.infradead.org
Subject: Re: [PATCH 2/4] ARM64: dts: meson-gx: Add Graphic Controller nodes
Date: Tue, 29 Nov 2016 21:16:17 +0200 [thread overview]
Message-ID: <1812737.pZP73QSyU1@avalon> (raw)
In-Reply-To: <1480416469-9655-3-git-send-email-narmstrong@baylibre.com>
Hi Neil,
Thank you for the patch.
On Tuesday 29 Nov 2016 11:47:47 Neil Armstrong wrote:
> Add Video Processing Unit and CVBS Output nodes, and enable CVBS on selected
> boards.
>
> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
> ---
> arch/arm64/boot/dts/amlogic/meson-gx.dtsi | 46 +++++++++++++++++++
> .../boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts | 4 ++
> arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi | 4 ++
> arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi | 8 ++++
> .../boot/dts/amlogic/meson-gxl-nexbox-a95x.dts | 4 ++
> arch/arm64/boot/dts/amlogic/meson-gxl.dtsi | 8 ++++
> .../arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts | 4 ++
> arch/arm64/boot/dts/amlogic/meson-gxm.dtsi | 8 ++++
> 8 files changed, 86 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/amlogic/meson-gx.dtsi
> b/arch/arm64/boot/dts/amlogic/meson-gx.dtsi index fc033c0..644d5f6 100644
> --- a/arch/arm64/boot/dts/amlogic/meson-gx.dtsi
> +++ b/arch/arm64/boot/dts/amlogic/meson-gx.dtsi
> @@ -153,6 +153,27 @@
> };
> };
>
> + venc_cvbs: venc-cvbs {
> + compatible = "amlogic,meson-gx-cvbs";
> + status = "disabled";
Still no registers here ?
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + venc_cvbs_in: port@0 {
Nitpicking, you don't need a label here as ports are never referenced by
phandle. Same for the vpu node below.
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0>;
> +
> + venc_cvbs_in_vpu: endpoint@0 {
> + reg = <0>;
And there's no requirement to number the endpoint if there's a single one of
them (but it's not forbidden either).
> + remote-endpoint =
<&vpu_out_venc_cvbs>;
> + };
> + };
> + };
> + };
> +
> soc {
> compatible = "simple-bus";
> #address-cells = <2>;
> @@ -356,5 +377,30 @@
> status = "disabled";
> };
> };
> +
> + vpu: vpu@d0100000 {
> + compatible = "amlogic,meson-gx-vpu";
> + reg = <0x0 0xd0100000 0x0 0x100000>,
> + <0x0 0xc883c000 0x0 0x1000>,
> + <0x0 0xc8838000 0x0 0x1000>;
> + reg-names = "base", "hhi", "dmc";
> + interrupts = <GIC_SPI 3 IRQ_TYPE_EDGE_RISING>;
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + vpu_out: port@1 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <1>;
> +
> + vpu_out_venc_cvbs: endpoint@0 {
> + reg = <0>;
> + remote-endpoint =
<&venc_cvbs_in_vpu>;
> + };
> + };
> + };
> + };
> };
> };
> diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts
> b/arch/arm64/boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts index
> 9696820..a55d1cf 100644
> --- a/arch/arm64/boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts
> +++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts
> @@ -229,3 +229,7 @@
> clocks = <&clkc CLKID_FCLK_DIV4>;
> clock-names = "clkin0";
> };
> +
> +&venc_cvbs {
> + status = "okay";
> +};
> diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi
> b/arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi index 5e5e2de..3c09bd1
> 100644
> --- a/arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi
> +++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi
> @@ -266,3 +266,7 @@
> clocks = <&clkc CLKID_FCLK_DIV4>;
> clock-names = "clkin0";
> };
> +
> +&venc_cvbs {
> + status = "okay";
> +};
> diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi
> b/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi index ac5ad3b..1a321c8f
> 100644
> --- a/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi
> +++ b/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi
> @@ -506,3 +506,11 @@
> <&clkc CLKID_FCLK_DIV2>;
> clock-names = "core", "clkin0", "clkin1";
> };
> +
> +&venc_cvbs {
> + compatible = "amlogic,meson-gxbb-cvbs", "amlogic,meson-gx-cvbs";
> +};
> +
> +&vpu {
> + compatible = "amlogic,meson-gxbb-vpu", "amlogic,meson-gx-vpu";
> +};
> diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-nexbox-a95x.dts
> b/arch/arm64/boot/dts/amlogic/meson-gxl-nexbox-a95x.dts index
> e99101a..2a9b46f 100644
> --- a/arch/arm64/boot/dts/amlogic/meson-gxl-nexbox-a95x.dts
> +++ b/arch/arm64/boot/dts/amlogic/meson-gxl-nexbox-a95x.dts
> @@ -203,3 +203,7 @@
> clocks = <&clkc CLKID_FCLK_DIV4>;
> clock-names = "clkin0";
> };
> +
> +&venc_cvbs {
> + status = "okay";
> +};
> diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl.dtsi
> b/arch/arm64/boot/dts/amlogic/meson-gxl.dtsi index 3af54dc..b60c5ce 100644
> --- a/arch/arm64/boot/dts/amlogic/meson-gxl.dtsi
> +++ b/arch/arm64/boot/dts/amlogic/meson-gxl.dtsi
> @@ -299,3 +299,11 @@
> <&clkc CLKID_FCLK_DIV2>;
> clock-names = "core", "clkin0", "clkin1";
> };
> +
> +&venc_cvbs {
> + compatible = "amlogic,meson-gxl-cvbs", "amlogic,meson-gx-cvbs";
> +};
> +
> +&vpu {
> + compatible = "amlogic,meson-gxl-vpu", "amlogic,meson-gx-vpu";
> +};
> diff --git a/arch/arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts
> b/arch/arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts index
> d320727..1ae2451 100644
> --- a/arch/arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts
> +++ b/arch/arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts
> @@ -167,3 +167,7 @@
> max-speed = <1000>;
> };
> };
> +
> +&venc_cvbs {
> + status = "okay";
> +};
> diff --git a/arch/arm64/boot/dts/amlogic/meson-gxm.dtsi
> b/arch/arm64/boot/dts/amlogic/meson-gxm.dtsi index c1974bb..fecd8c2 100644
> --- a/arch/arm64/boot/dts/amlogic/meson-gxm.dtsi
> +++ b/arch/arm64/boot/dts/amlogic/meson-gxm.dtsi
> @@ -112,3 +112,11 @@
> };
> };
> };
> +
> +&venc_cvbs {
> + compatible = "amlogic,meson-gxm-cvbs", "amlogic,meson-gx-cvbs";
> +};
> +
> +&vpu {
> + compatible = "amlogic,meson-gxm-vpu", "amlogic,meson-gx-vpu";
> +};
--
Regards,
Laurent Pinchart
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
WARNING: multiple messages have this Message-ID (diff)
From: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
To: Neil Armstrong <narmstrong@baylibre.com>
Cc: airlied@linux.ie, khilman@baylibre.com, carlo@caione.org,
dri-devel@lists.freedesktop.org,
linux-amlogic@lists.infradead.org,
linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org, victor.wan@amlogic.com,
jerry.cao@amlogic.com, Xing.Xu@amlogic.com,
devicetree@vger.kernel.org, daniel@ffwll.ch
Subject: Re: [PATCH 2/4] ARM64: dts: meson-gx: Add Graphic Controller nodes
Date: Tue, 29 Nov 2016 21:16:17 +0200 [thread overview]
Message-ID: <1812737.pZP73QSyU1@avalon> (raw)
In-Reply-To: <1480416469-9655-3-git-send-email-narmstrong@baylibre.com>
Hi Neil,
Thank you for the patch.
On Tuesday 29 Nov 2016 11:47:47 Neil Armstrong wrote:
> Add Video Processing Unit and CVBS Output nodes, and enable CVBS on selected
> boards.
>
> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
> ---
> arch/arm64/boot/dts/amlogic/meson-gx.dtsi | 46 +++++++++++++++++++
> .../boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts | 4 ++
> arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi | 4 ++
> arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi | 8 ++++
> .../boot/dts/amlogic/meson-gxl-nexbox-a95x.dts | 4 ++
> arch/arm64/boot/dts/amlogic/meson-gxl.dtsi | 8 ++++
> .../arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts | 4 ++
> arch/arm64/boot/dts/amlogic/meson-gxm.dtsi | 8 ++++
> 8 files changed, 86 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/amlogic/meson-gx.dtsi
> b/arch/arm64/boot/dts/amlogic/meson-gx.dtsi index fc033c0..644d5f6 100644
> --- a/arch/arm64/boot/dts/amlogic/meson-gx.dtsi
> +++ b/arch/arm64/boot/dts/amlogic/meson-gx.dtsi
> @@ -153,6 +153,27 @@
> };
> };
>
> + venc_cvbs: venc-cvbs {
> + compatible = "amlogic,meson-gx-cvbs";
> + status = "disabled";
Still no registers here ?
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + venc_cvbs_in: port@0 {
Nitpicking, you don't need a label here as ports are never referenced by
phandle. Same for the vpu node below.
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0>;
> +
> + venc_cvbs_in_vpu: endpoint@0 {
> + reg = <0>;
And there's no requirement to number the endpoint if there's a single one of
them (but it's not forbidden either).
> + remote-endpoint =
<&vpu_out_venc_cvbs>;
> + };
> + };
> + };
> + };
> +
> soc {
> compatible = "simple-bus";
> #address-cells = <2>;
> @@ -356,5 +377,30 @@
> status = "disabled";
> };
> };
> +
> + vpu: vpu@d0100000 {
> + compatible = "amlogic,meson-gx-vpu";
> + reg = <0x0 0xd0100000 0x0 0x100000>,
> + <0x0 0xc883c000 0x0 0x1000>,
> + <0x0 0xc8838000 0x0 0x1000>;
> + reg-names = "base", "hhi", "dmc";
> + interrupts = <GIC_SPI 3 IRQ_TYPE_EDGE_RISING>;
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + vpu_out: port@1 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <1>;
> +
> + vpu_out_venc_cvbs: endpoint@0 {
> + reg = <0>;
> + remote-endpoint =
<&venc_cvbs_in_vpu>;
> + };
> + };
> + };
> + };
> };
> };
> diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts
> b/arch/arm64/boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts index
> 9696820..a55d1cf 100644
> --- a/arch/arm64/boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts
> +++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts
> @@ -229,3 +229,7 @@
> clocks = <&clkc CLKID_FCLK_DIV4>;
> clock-names = "clkin0";
> };
> +
> +&venc_cvbs {
> + status = "okay";
> +};
> diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi
> b/arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi index 5e5e2de..3c09bd1
> 100644
> --- a/arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi
> +++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi
> @@ -266,3 +266,7 @@
> clocks = <&clkc CLKID_FCLK_DIV4>;
> clock-names = "clkin0";
> };
> +
> +&venc_cvbs {
> + status = "okay";
> +};
> diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi
> b/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi index ac5ad3b..1a321c8f
> 100644
> --- a/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi
> +++ b/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi
> @@ -506,3 +506,11 @@
> <&clkc CLKID_FCLK_DIV2>;
> clock-names = "core", "clkin0", "clkin1";
> };
> +
> +&venc_cvbs {
> + compatible = "amlogic,meson-gxbb-cvbs", "amlogic,meson-gx-cvbs";
> +};
> +
> +&vpu {
> + compatible = "amlogic,meson-gxbb-vpu", "amlogic,meson-gx-vpu";
> +};
> diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-nexbox-a95x.dts
> b/arch/arm64/boot/dts/amlogic/meson-gxl-nexbox-a95x.dts index
> e99101a..2a9b46f 100644
> --- a/arch/arm64/boot/dts/amlogic/meson-gxl-nexbox-a95x.dts
> +++ b/arch/arm64/boot/dts/amlogic/meson-gxl-nexbox-a95x.dts
> @@ -203,3 +203,7 @@
> clocks = <&clkc CLKID_FCLK_DIV4>;
> clock-names = "clkin0";
> };
> +
> +&venc_cvbs {
> + status = "okay";
> +};
> diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl.dtsi
> b/arch/arm64/boot/dts/amlogic/meson-gxl.dtsi index 3af54dc..b60c5ce 100644
> --- a/arch/arm64/boot/dts/amlogic/meson-gxl.dtsi
> +++ b/arch/arm64/boot/dts/amlogic/meson-gxl.dtsi
> @@ -299,3 +299,11 @@
> <&clkc CLKID_FCLK_DIV2>;
> clock-names = "core", "clkin0", "clkin1";
> };
> +
> +&venc_cvbs {
> + compatible = "amlogic,meson-gxl-cvbs", "amlogic,meson-gx-cvbs";
> +};
> +
> +&vpu {
> + compatible = "amlogic,meson-gxl-vpu", "amlogic,meson-gx-vpu";
> +};
> diff --git a/arch/arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts
> b/arch/arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts index
> d320727..1ae2451 100644
> --- a/arch/arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts
> +++ b/arch/arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts
> @@ -167,3 +167,7 @@
> max-speed = <1000>;
> };
> };
> +
> +&venc_cvbs {
> + status = "okay";
> +};
> diff --git a/arch/arm64/boot/dts/amlogic/meson-gxm.dtsi
> b/arch/arm64/boot/dts/amlogic/meson-gxm.dtsi index c1974bb..fecd8c2 100644
> --- a/arch/arm64/boot/dts/amlogic/meson-gxm.dtsi
> +++ b/arch/arm64/boot/dts/amlogic/meson-gxm.dtsi
> @@ -112,3 +112,11 @@
> };
> };
> };
> +
> +&venc_cvbs {
> + compatible = "amlogic,meson-gxm-cvbs", "amlogic,meson-gx-cvbs";
> +};
> +
> +&vpu {
> + compatible = "amlogic,meson-gxm-vpu", "amlogic,meson-gx-vpu";
> +};
--
Regards,
Laurent Pinchart
next prev parent reply other threads:[~2016-11-29 19:16 UTC|newest]
Thread overview: 28+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-11-29 10:47 [PATCH 0/4] drm: Add support for the Amlogic Video Processing Unit Neil Armstrong
2016-11-29 10:47 ` Neil Armstrong
2016-11-29 10:47 ` Neil Armstrong
2016-11-29 10:47 ` [PATCH 1/4] drm: Add support for Amlogic Meson Graphic Controller Neil Armstrong
2016-11-29 10:47 ` Neil Armstrong
2016-11-29 10:47 ` [PATCH 2/4] ARM64: dts: meson-gx: Add Graphic Controller nodes Neil Armstrong
2016-11-29 10:47 ` Neil Armstrong
2016-11-29 10:47 ` Neil Armstrong
2016-11-29 10:47 ` Neil Armstrong
2016-11-29 19:16 ` Laurent Pinchart [this message]
2016-11-29 19:16 ` Laurent Pinchart
2016-11-29 19:16 ` Laurent Pinchart
2016-11-29 19:16 ` Laurent Pinchart
2016-11-29 19:19 ` Laurent Pinchart
2016-11-29 19:19 ` Laurent Pinchart
2016-11-29 19:19 ` Laurent Pinchart
2016-11-29 19:19 ` Laurent Pinchart
2016-11-29 10:47 ` [PATCH 3/4] dt-bindings: display: add Amlogic Meson DRM Bindings Neil Armstrong
2016-11-29 10:47 ` Neil Armstrong
2016-11-29 10:47 ` Neil Armstrong
2016-11-29 10:47 ` Neil Armstrong
2016-11-29 10:47 ` [PATCH 4/4] MAINTAINERS: add entry for Amlogic DRM drivers Neil Armstrong
2016-11-29 10:47 ` Neil Armstrong
2016-11-29 10:47 ` Neil Armstrong
2016-11-29 14:16 ` [PATCH 0/4] drm: Add support for the Amlogic Video Processing Unit Daniel Vetter
2016-11-29 14:16 ` Daniel Vetter
2016-11-29 14:16 ` Daniel Vetter
2016-11-29 14:16 ` Daniel Vetter
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1812737.pZP73QSyU1@avalon \
--to=laurent.pinchart@ideasonboard.com \
--cc=linus-amlogic@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.