* [PATCH 1/3] sunxi: dts: arm64: update devicetree files from Linux-v6.6-rc6
2023-10-20 0:26 [PATCH 0/3] sunxi: devicetree updates from Linux v6.6 Andre Przywara
@ 2023-10-20 0:26 ` Andre Przywara
2023-10-20 0:26 ` [PATCH 2/3] sunxi: dts: arm: " Andre Przywara
` (2 subsequent siblings)
3 siblings, 0 replies; 5+ messages in thread
From: Andre Przywara @ 2023-10-20 0:26 UTC (permalink / raw)
To: Jagan Teki
Cc: Jernej Skrabec, Samuel Holland, u-boot, linux-sunxi, Simon Glass,
Tom Rini, Ludwig Kormann
Sync the devicetree files from the official Linux kernel tree, v6.6-rc6.
This is covering Allwinner SoCs with 64-bit ARM cores.
Only small cosmetic changes (clock name fixed), but we add the DT for
the new OrangePi Zero 3 board, for which U-Boot enablement patches are
pending.
As before, this omits the non-backwards compatible changes to the R_INTC
controller, to remain compatible with older kernels.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
arch/arm/dts/sun50i-a64.dtsi | 3 +-
arch/arm/dts/sun50i-h6-pine-h64-model-b.dts | 2 +-
arch/arm/dts/sun50i-h616-orangepi-zero.dtsi | 134 ++++++++++++++++++++
arch/arm/dts/sun50i-h616-orangepi-zero2.dts | 121 +-----------------
arch/arm/dts/sun50i-h616-x96-mate.dts | 2 +-
arch/arm/dts/sun50i-h618-orangepi-zero3.dts | 94 ++++++++++++++
include/dt-bindings/clock/sun50i-h6-ccu.h | 2 +-
include/dt-bindings/clock/sun50i-h616-ccu.h | 2 +-
include/dt-bindings/clock/sun6i-rtc.h | 2 +-
include/dt-bindings/reset/sun50i-h6-ccu.h | 2 +-
include/dt-bindings/reset/sun50i-h6-r-ccu.h | 2 +-
include/dt-bindings/reset/sun50i-h616-ccu.h | 2 +-
12 files changed, 240 insertions(+), 128 deletions(-)
create mode 100644 arch/arm/dts/sun50i-h616-orangepi-zero.dtsi
create mode 100644 arch/arm/dts/sun50i-h618-orangepi-zero3.dts
diff --git a/arch/arm/dts/sun50i-a64.dtsi b/arch/arm/dts/sun50i-a64.dtsi
index 135762b34fd..2240eaec5dd 100644
--- a/arch/arm/dts/sun50i-a64.dtsi
+++ b/arch/arm/dts/sun50i-a64.dtsi
@@ -93,6 +93,7 @@
L2: l2-cache {
compatible = "cache";
cache-level = <2>;
+ cache-unified;
};
};
@@ -407,7 +408,7 @@
interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&ccu CLK_BUS_TCON0>, <&ccu CLK_TCON0>;
clock-names = "ahb", "tcon-ch0";
- clock-output-names = "tcon-pixel-clock";
+ clock-output-names = "tcon-data-clock";
#clock-cells = <0>;
resets = <&ccu RST_BUS_TCON0>, <&ccu RST_BUS_LVDS>;
reset-names = "lcd", "lvds";
diff --git a/arch/arm/dts/sun50i-h6-pine-h64-model-b.dts b/arch/arm/dts/sun50i-h6-pine-h64-model-b.dts
index 686f58e7700..b710f1a0f53 100644
--- a/arch/arm/dts/sun50i-h6-pine-h64-model-b.dts
+++ b/arch/arm/dts/sun50i-h6-pine-h64-model-b.dts
@@ -1,4 +1,4 @@
-// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
/*
* Copyright (C) 2019 Corentin LABBE <clabbe@baylibre.com>
*/
diff --git a/arch/arm/dts/sun50i-h616-orangepi-zero.dtsi b/arch/arm/dts/sun50i-h616-orangepi-zero.dtsi
new file mode 100644
index 00000000000..15290e6892f
--- /dev/null
+++ b/arch/arm/dts/sun50i-h616-orangepi-zero.dtsi
@@ -0,0 +1,134 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2020 Arm Ltd.
+ *
+ * DT nodes common between Orange Pi Zero 2 and Orange Pi Zero 3.
+ * Excludes PMIC nodes and properties, since they are different between the two.
+ */
+
+#include "sun50i-h616.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+ aliases {
+ ethernet0 = &emac0;
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led-0 {
+ function = LED_FUNCTION_POWER;
+ color = <LED_COLOR_ID_RED>;
+ gpios = <&pio 2 12 GPIO_ACTIVE_HIGH>; /* PC12 */
+ default-state = "on";
+ };
+
+ led-1 {
+ function = LED_FUNCTION_STATUS;
+ color = <LED_COLOR_ID_GREEN>;
+ gpios = <&pio 2 13 GPIO_ACTIVE_HIGH>; /* PC13 */
+ };
+ };
+
+ reg_vcc5v: vcc5v {
+ /* board wide 5V supply directly from the USB-C socket */
+ compatible = "regulator-fixed";
+ regulator-name = "vcc-5v";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ };
+
+ reg_usb1_vbus: regulator-usb1-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb1-vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <®_vcc5v>;
+ enable-active-high;
+ gpio = <&pio 2 16 GPIO_ACTIVE_HIGH>; /* PC16 */
+ };
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+/* USB 2 & 3 are on headers only. */
+
+&emac0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ext_rgmii_pins>;
+ phy-mode = "rgmii";
+ phy-handle = <&ext_rgmii_phy>;
+ allwinner,rx-delay-ps = <3100>;
+ allwinner,tx-delay-ps = <700>;
+ status = "okay";
+};
+
+&mdio0 {
+ ext_rgmii_phy: ethernet-phy@1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ };
+};
+
+&mmc0 {
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
+ bus-width = <4>;
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&spi0 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi0_pins>, <&spi0_cs0_pin>;
+
+ flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <40000000>;
+ };
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_ph_pins>;
+ status = "okay";
+};
+
+&usbotg {
+ /*
+ * PHY0 pins are connected to a USB-C socket, but a role switch
+ * is not implemented: both CC pins are pulled to GND.
+ * The VBUS pins power the device, so a fixed peripheral mode
+ * is the best choice.
+ * The board can be powered via GPIOs, in this case port0 *can*
+ * act as a host (with a cable/adapter ignoring CC), as VBUS is
+ * then provided by the GPIOs. Any user of this setup would
+ * need to adjust the DT accordingly: dr_mode set to "host",
+ * enabling OHCI0 and EHCI0.
+ */
+ dr_mode = "peripheral";
+ status = "okay";
+};
+
+&usbphy {
+ usb1_vbus-supply = <®_usb1_vbus>;
+ status = "okay";
+};
diff --git a/arch/arm/dts/sun50i-h616-orangepi-zero2.dts b/arch/arm/dts/sun50i-h616-orangepi-zero2.dts
index cb8600d0ea1..d83852e72f0 100644
--- a/arch/arm/dts/sun50i-h616-orangepi-zero2.dts
+++ b/arch/arm/dts/sun50i-h616-orangepi-zero2.dts
@@ -1,99 +1,23 @@
-// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
/*
* Copyright (C) 2020 Arm Ltd.
*/
/dts-v1/;
-#include "sun50i-h616.dtsi"
-
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/interrupt-controller/arm-gic.h>
-#include <dt-bindings/leds/common.h>
+#include "sun50i-h616-orangepi-zero.dtsi"
/ {
model = "OrangePi Zero2";
compatible = "xunlong,orangepi-zero2", "allwinner,sun50i-h616";
-
- aliases {
- ethernet0 = &emac0;
- serial0 = &uart0;
- };
-
- chosen {
- stdout-path = "serial0:115200n8";
- };
-
- leds {
- compatible = "gpio-leds";
-
- led-0 {
- function = LED_FUNCTION_POWER;
- color = <LED_COLOR_ID_RED>;
- gpios = <&pio 2 12 GPIO_ACTIVE_HIGH>; /* PC12 */
- default-state = "on";
- };
-
- led-1 {
- function = LED_FUNCTION_STATUS;
- color = <LED_COLOR_ID_GREEN>;
- gpios = <&pio 2 13 GPIO_ACTIVE_HIGH>; /* PC13 */
- };
- };
-
- reg_vcc5v: vcc5v {
- /* board wide 5V supply directly from the USB-C socket */
- compatible = "regulator-fixed";
- regulator-name = "vcc-5v";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- regulator-always-on;
- };
-
- reg_usb1_vbus: regulator-usb1-vbus {
- compatible = "regulator-fixed";
- regulator-name = "usb1-vbus";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- vin-supply = <®_vcc5v>;
- enable-active-high;
- gpio = <&pio 2 16 GPIO_ACTIVE_HIGH>; /* PC16 */
- };
};
-&ehci1 {
- status = "okay";
-};
-
-/* USB 2 & 3 are on headers only. */
-
&emac0 {
- pinctrl-names = "default";
- pinctrl-0 = <&ext_rgmii_pins>;
- phy-mode = "rgmii";
- phy-handle = <&ext_rgmii_phy>;
phy-supply = <®_dcdce>;
- allwinner,rx-delay-ps = <3100>;
- allwinner,tx-delay-ps = <700>;
- status = "okay";
-};
-
-&mdio0 {
- ext_rgmii_phy: ethernet-phy@1 {
- compatible = "ethernet-phy-ieee802.3-c22";
- reg = <1>;
- };
};
&mmc0 {
vmmc-supply = <®_dcdce>;
- cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
- bus-width = <4>;
- status = "okay";
-};
-
-&ohci1 {
- status = "okay";
};
&r_rsb {
@@ -211,44 +135,3 @@
vcc-ph-supply = <®_aldo1>;
vcc-pi-supply = <®_aldo1>;
};
-
-&spi0 {
- status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&spi0_pins>, <&spi0_cs0_pin>;
-
- flash@0 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "jedec,spi-nor";
- reg = <0>;
- spi-max-frequency = <40000000>;
- };
-};
-
-&uart0 {
- pinctrl-names = "default";
- pinctrl-0 = <&uart0_ph_pins>;
- status = "okay";
-};
-
-&usbotg {
- /*
- * PHY0 pins are connected to a USB-C socket, but a role switch
- * is not implemented: both CC pins are pulled to GND.
- * The VBUS pins power the device, so a fixed peripheral mode
- * is the best choice.
- * The board can be powered via GPIOs, in this case port0 *can*
- * act as a host (with a cable/adapter ignoring CC), as VBUS is
- * then provided by the GPIOs. Any user of this setup would
- * need to adjust the DT accordingly: dr_mode set to "host",
- * enabling OHCI0 and EHCI0.
- */
- dr_mode = "peripheral";
- status = "okay";
-};
-
-&usbphy {
- usb1_vbus-supply = <®_usb1_vbus>;
- status = "okay";
-};
diff --git a/arch/arm/dts/sun50i-h616-x96-mate.dts b/arch/arm/dts/sun50i-h616-x96-mate.dts
index 07424c28b69..959b6fd1848 100644
--- a/arch/arm/dts/sun50i-h616-x96-mate.dts
+++ b/arch/arm/dts/sun50i-h616-x96-mate.dts
@@ -1,4 +1,4 @@
-// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
/*
* Copyright (C) 2021 Arm Ltd.
*/
diff --git a/arch/arm/dts/sun50i-h618-orangepi-zero3.dts b/arch/arm/dts/sun50i-h618-orangepi-zero3.dts
new file mode 100644
index 00000000000..00fe28caac9
--- /dev/null
+++ b/arch/arm/dts/sun50i-h618-orangepi-zero3.dts
@@ -0,0 +1,94 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2023 Arm Ltd.
+ */
+
+/dts-v1/;
+
+#include "sun50i-h616-orangepi-zero.dtsi"
+
+/ {
+ model = "OrangePi Zero3";
+ compatible = "xunlong,orangepi-zero3", "allwinner,sun50i-h618";
+};
+
+&emac0 {
+ phy-supply = <®_dldo1>;
+};
+
+&ext_rgmii_phy {
+ motorcomm,clk-out-frequency-hz = <125000000>;
+};
+
+&mmc0 {
+ /*
+ * The schematic shows the card detect pin wired up to PF6, via an
+ * inverter, but it just doesn't work.
+ */
+ broken-cd;
+ vmmc-supply = <®_dldo1>;
+};
+
+&r_i2c {
+ status = "okay";
+
+ axp313: pmic@36 {
+ compatible = "x-powers,axp313a";
+ reg = <0x36>;
+ #interrupt-cells = <1>;
+ interrupt-controller;
+ interrupt-parent = <&pio>;
+ interrupts = <2 9 IRQ_TYPE_LEVEL_LOW>; /* PC9 */
+
+ vin1-supply = <®_vcc5v>;
+ vin2-supply = <®_vcc5v>;
+ vin3-supply = <®_vcc5v>;
+
+ regulators {
+ /* Supplies VCC-PLL, so needs to be always on. */
+ reg_aldo1: aldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc1v8";
+ };
+
+ /* Supplies VCC-IO, so needs to be always on. */
+ reg_dldo1: dldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc3v3";
+ };
+
+ reg_dcdc1: dcdc1 {
+ regulator-always-on;
+ regulator-min-microvolt = <810000>;
+ regulator-max-microvolt = <990000>;
+ regulator-name = "vdd-gpu-sys";
+ };
+
+ reg_dcdc2: dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <810000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-cpu";
+ };
+
+ reg_dcdc3: dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-dram";
+ };
+ };
+ };
+};
+
+&pio {
+ vcc-pc-supply = <®_dldo1>;
+ vcc-pf-supply = <®_dldo1>;
+ vcc-pg-supply = <®_aldo1>;
+ vcc-ph-supply = <®_dldo1>;
+ vcc-pi-supply = <®_dldo1>;
+};
diff --git a/include/dt-bindings/clock/sun50i-h6-ccu.h b/include/dt-bindings/clock/sun50i-h6-ccu.h
index a1545cd60e7..ef9123d8193 100644
--- a/include/dt-bindings/clock/sun50i-h6-ccu.h
+++ b/include/dt-bindings/clock/sun50i-h6-ccu.h
@@ -1,4 +1,4 @@
-// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+/* SPDX-License-Identifier: (GPL-2.0+ OR MIT) */
/*
* Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io>
*/
diff --git a/include/dt-bindings/clock/sun50i-h616-ccu.h b/include/dt-bindings/clock/sun50i-h616-ccu.h
index 1191aca53ac..6f8f01e6762 100644
--- a/include/dt-bindings/clock/sun50i-h616-ccu.h
+++ b/include/dt-bindings/clock/sun50i-h616-ccu.h
@@ -1,4 +1,4 @@
-/* SPDX-License-Identifier: (GPL-2.0+ or MIT) */
+/* SPDX-License-Identifier: (GPL-2.0+ OR MIT) */
/*
* Copyright (C) 2020 Arm Ltd.
*/
diff --git a/include/dt-bindings/clock/sun6i-rtc.h b/include/dt-bindings/clock/sun6i-rtc.h
index c845493e4d3..3bd3aa3d57c 100644
--- a/include/dt-bindings/clock/sun6i-rtc.h
+++ b/include/dt-bindings/clock/sun6i-rtc.h
@@ -1,4 +1,4 @@
-/* SPDX-License-Identifier: (GPL-2.0+ or MIT) */
+/* SPDX-License-Identifier: (GPL-2.0+ OR MIT) */
#ifndef _DT_BINDINGS_CLK_SUN6I_RTC_H_
#define _DT_BINDINGS_CLK_SUN6I_RTC_H_
diff --git a/include/dt-bindings/reset/sun50i-h6-ccu.h b/include/dt-bindings/reset/sun50i-h6-ccu.h
index 81106f45509..d038ddfa481 100644
--- a/include/dt-bindings/reset/sun50i-h6-ccu.h
+++ b/include/dt-bindings/reset/sun50i-h6-ccu.h
@@ -1,4 +1,4 @@
-// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+/* SPDX-License-Identifier: (GPL-2.0+ OR MIT) */
/*
* Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io>
*/
diff --git a/include/dt-bindings/reset/sun50i-h6-r-ccu.h b/include/dt-bindings/reset/sun50i-h6-r-ccu.h
index 7950e799c76..d541ade884f 100644
--- a/include/dt-bindings/reset/sun50i-h6-r-ccu.h
+++ b/include/dt-bindings/reset/sun50i-h6-r-ccu.h
@@ -1,4 +1,4 @@
-/* SPDX-License-Identifier: (GPL-2.0+ or MIT) */
+/* SPDX-License-Identifier: (GPL-2.0+ OR MIT) */
/*
* Copyright (C) 2016 Icenowy Zheng <icenowy@aosc.xyz>
*/
diff --git a/include/dt-bindings/reset/sun50i-h616-ccu.h b/include/dt-bindings/reset/sun50i-h616-ccu.h
index cb6285a8d12..1bd8bb0a11b 100644
--- a/include/dt-bindings/reset/sun50i-h616-ccu.h
+++ b/include/dt-bindings/reset/sun50i-h616-ccu.h
@@ -1,4 +1,4 @@
-/* SPDX-License-Identifier: (GPL-2.0+ or MIT) */
+/* SPDX-License-Identifier: (GPL-2.0+ OR MIT) */
/*
* Copyright (C) 2020 Arm Ltd.
*/
--
2.35.8
^ permalink raw reply related [flat|nested] 5+ messages in thread* [PATCH 3/3] sunxi: dts: arm: add T113s/D1 DT files from Linux-v6.6-rc6
2023-10-20 0:26 [PATCH 0/3] sunxi: devicetree updates from Linux v6.6 Andre Przywara
2023-10-20 0:26 ` [PATCH 1/3] sunxi: dts: arm64: update devicetree files from Linux-v6.6-rc6 Andre Przywara
2023-10-20 0:26 ` [PATCH 2/3] sunxi: dts: arm: " Andre Przywara
@ 2023-10-20 0:26 ` Andre Przywara
2023-10-21 7:49 ` [PATCH 0/3] sunxi: devicetree updates from Linux v6.6 Jernej Škrabec
3 siblings, 0 replies; 5+ messages in thread
From: Andre Przywara @ 2023-10-20 0:26 UTC (permalink / raw)
To: Jagan Teki
Cc: Jernej Skrabec, Samuel Holland, u-boot, linux-sunxi, Simon Glass,
Tom Rini, Ludwig Kormann
This copies in some devicetree files from the official Linux kernel tree,
v6.6-rc6. It covers a board with the Allwinner T113s SoC, which shares
many devices with its RISC-V sibling, the Allwinner D1(s). This is the
reason for the core .dtsi files landing in the arch/riscv directory.
We are only adjusting the include path to accommodate for the differences
in the U-Boot build system.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
.../arm/dts/sun8i-t113s-mangopi-mq-r-t113.dts | 35 +
arch/arm/dts/sun8i-t113s.dtsi | 59 ++
arch/arm/dts/sunxi-d1s-t113-mangopi-mq-r.dtsi | 126 +++
arch/riscv/dts/sunxi-d1-t113.dtsi | 15 +
arch/riscv/dts/sunxi-d1s-t113.dtsi | 927 ++++++++++++++++++
include/dt-bindings/clock/sun20i-d1-ccu.h | 158 +++
include/dt-bindings/clock/sun20i-d1-r-ccu.h | 19 +
include/dt-bindings/reset/sun20i-d1-ccu.h | 79 ++
include/dt-bindings/reset/sun20i-d1-r-ccu.h | 16 +
9 files changed, 1434 insertions(+)
create mode 100644 arch/arm/dts/sun8i-t113s-mangopi-mq-r-t113.dts
create mode 100644 arch/arm/dts/sun8i-t113s.dtsi
create mode 100644 arch/arm/dts/sunxi-d1s-t113-mangopi-mq-r.dtsi
create mode 100644 arch/riscv/dts/sunxi-d1-t113.dtsi
create mode 100644 arch/riscv/dts/sunxi-d1s-t113.dtsi
create mode 100644 include/dt-bindings/clock/sun20i-d1-ccu.h
create mode 100644 include/dt-bindings/clock/sun20i-d1-r-ccu.h
create mode 100644 include/dt-bindings/reset/sun20i-d1-ccu.h
create mode 100644 include/dt-bindings/reset/sun20i-d1-r-ccu.h
diff --git a/arch/arm/dts/sun8i-t113s-mangopi-mq-r-t113.dts b/arch/arm/dts/sun8i-t113s-mangopi-mq-r-t113.dts
new file mode 100644
index 00000000000..8b3a7538381
--- /dev/null
+++ b/arch/arm/dts/sun8i-t113s-mangopi-mq-r-t113.dts
@@ -0,0 +1,35 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+// Copyright (C) 2022 Arm Ltd.
+
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/dts-v1/;
+
+#include "sun8i-t113s.dtsi"
+#include "sunxi-d1s-t113-mangopi-mq-r.dtsi"
+
+/ {
+ model = "MangoPi MQ-R-T113";
+ compatible = "widora,mangopi-mq-r-t113", "allwinner,sun8i-t113s";
+
+ aliases {
+ ethernet0 = &rtl8189ftv;
+ };
+};
+
+&cpu0 {
+ cpu-supply = <®_vcc_core>;
+};
+
+&cpu1 {
+ cpu-supply = <®_vcc_core>;
+};
+
+&mmc1 {
+ rtl8189ftv: wifi@1 {
+ reg = <1>;
+ interrupt-parent = <&pio>;
+ interrupts = <6 10 IRQ_TYPE_LEVEL_LOW>; /* PG10 = WL_WAKE_AP */
+ interrupt-names = "host-wake";
+ };
+};
diff --git a/arch/arm/dts/sun8i-t113s.dtsi b/arch/arm/dts/sun8i-t113s.dtsi
new file mode 100644
index 00000000000..b94b69142af
--- /dev/null
+++ b/arch/arm/dts/sun8i-t113s.dtsi
@@ -0,0 +1,59 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+// Copyright (C) 2022 Arm Ltd.
+
+#define SOC_PERIPHERAL_IRQ(nr) GIC_SPI nr
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <../../riscv/dts/sunxi-d1s-t113.dtsi>
+#include <../../riscv/dts/sunxi-d1-t113.dtsi>
+
+/ {
+ interrupt-parent = <&gic>;
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu0: cpu@0 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <0>;
+ clocks = <&ccu CLK_CPUX>;
+ clock-names = "cpu";
+ };
+
+ cpu1: cpu@1 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <1>;
+ clocks = <&ccu CLK_CPUX>;
+ clock-names = "cpu";
+ };
+ };
+
+ gic: interrupt-controller@1c81000 {
+ compatible = "arm,gic-400";
+ reg = <0x03021000 0x1000>,
+ <0x03022000 0x2000>,
+ <0x03024000 0x2000>,
+ <0x03026000 0x2000>;
+ interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ };
+
+ timer {
+ compatible = "arm,armv7-timer";
+ interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+ };
+
+ pmu {
+ compatible = "arm,cortex-a7-pmu";
+ interrupts = <GIC_SPI 172 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 173 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-affinity = <&cpu0>, <&cpu1>;
+ };
+};
diff --git a/arch/arm/dts/sunxi-d1s-t113-mangopi-mq-r.dtsi b/arch/arm/dts/sunxi-d1s-t113-mangopi-mq-r.dtsi
new file mode 100644
index 00000000000..a415c4a78a7
--- /dev/null
+++ b/arch/arm/dts/sunxi-d1s-t113-mangopi-mq-r.dtsi
@@ -0,0 +1,126 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+// Copyright (C) 2022 Arm Ltd.
+/*
+ * Common peripherals and configurations for MangoPi MQ-R boards.
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+ aliases {
+ serial3 = &uart3;
+ };
+
+ chosen {
+ stdout-path = "serial3:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led-0 {
+ color = <LED_COLOR_ID_BLUE>;
+ function = LED_FUNCTION_STATUS;
+ gpios = <&pio 3 22 GPIO_ACTIVE_LOW>; /* PD22 */
+ };
+ };
+
+ /* board wide 5V supply directly from the USB-C socket */
+ reg_vcc5v: regulator-5v {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc-5v";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ };
+
+ /* SY8008 DC/DC regulator on the board */
+ reg_3v3: regulator-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc-3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <®_vcc5v>;
+ };
+
+ /* SY8008 DC/DC regulator on the board, also supplying VDD-SYS */
+ reg_vcc_core: regulator-core {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc-core";
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <880000>;
+ vin-supply = <®_vcc5v>;
+ };
+
+ /* XC6206 LDO on the board */
+ reg_avdd2v8: regulator-avdd {
+ compatible = "regulator-fixed";
+ regulator-name = "avdd2v8";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ vin-supply = <®_3v3>;
+ };
+
+ wifi_pwrseq: wifi-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&pio 6 12 GPIO_ACTIVE_LOW>; /* PG12 */
+ };
+};
+
+&dcxo {
+ clock-frequency = <24000000>;
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&mmc0 {
+ pinctrl-0 = <&mmc0_pins>;
+ pinctrl-names = "default";
+ vmmc-supply = <®_3v3>;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
+ disable-wp;
+ bus-width = <4>;
+ status = "okay";
+};
+
+&mmc1 {
+ pinctrl-0 = <&mmc1_pins>;
+ pinctrl-names = "default";
+ vmmc-supply = <®_3v3>;
+ non-removable;
+ bus-width = <4>;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&pio {
+ vcc-pb-supply = <®_3v3>;
+ vcc-pd-supply = <®_3v3>;
+ vcc-pe-supply = <®_avdd2v8>;
+ vcc-pf-supply = <®_3v3>;
+ vcc-pg-supply = <®_3v3>;
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart3_pb_pins>;
+ status = "okay";
+};
+
+/* The USB-C socket has its CC pins pulled to GND, so is hardwired as a UFP. */
+&usb_otg {
+ dr_mode = "peripheral";
+ status = "okay";
+};
+
+&usbphy {
+ usb1_vbus-supply = <®_vcc5v>;
+ status = "okay";
+};
diff --git a/arch/riscv/dts/sunxi-d1-t113.dtsi b/arch/riscv/dts/sunxi-d1-t113.dtsi
new file mode 100644
index 00000000000..b7156123df5
--- /dev/null
+++ b/arch/riscv/dts/sunxi-d1-t113.dtsi
@@ -0,0 +1,15 @@
+// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+// Copyright (C) 2021-2022 Samuel Holland <samuel@sholland.org>
+
+/ {
+ soc {
+ dsp_wdt: watchdog@1700400 {
+ compatible = "allwinner,sun20i-d1-wdt";
+ reg = <0x1700400 0x20>;
+ interrupts = <SOC_PERIPHERAL_IRQ(122) IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&dcxo>, <&rtc CLK_OSC32K>;
+ clock-names = "hosc", "losc";
+ status = "reserved";
+ };
+ };
+};
diff --git a/arch/riscv/dts/sunxi-d1s-t113.dtsi b/arch/riscv/dts/sunxi-d1s-t113.dtsi
new file mode 100644
index 00000000000..822f022eec2
--- /dev/null
+++ b/arch/riscv/dts/sunxi-d1s-t113.dtsi
@@ -0,0 +1,927 @@
+// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+// Copyright (C) 2021-2022 Samuel Holland <samuel@sholland.org>
+
+#include <dt-bindings/clock/sun6i-rtc.h>
+#include <dt-bindings/clock/sun8i-de2.h>
+#include <dt-bindings/clock/sun8i-tcon-top.h>
+#include <dt-bindings/clock/sun20i-d1-ccu.h>
+#include <dt-bindings/clock/sun20i-d1-r-ccu.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/reset/sun8i-de2.h>
+#include <dt-bindings/reset/sun20i-d1-ccu.h>
+#include <dt-bindings/reset/sun20i-d1-r-ccu.h>
+
+/ {
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ dcxo: dcxo-clk {
+ compatible = "fixed-clock";
+ clock-output-names = "dcxo";
+ #clock-cells = <0>;
+ };
+
+ de: display-engine {
+ compatible = "allwinner,sun20i-d1-display-engine";
+ allwinner,pipelines = <&mixer0>, <&mixer1>;
+ status = "disabled";
+ };
+
+ soc {
+ compatible = "simple-bus";
+ ranges;
+ dma-noncoherent;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ pio: pinctrl@2000000 {
+ compatible = "allwinner,sun20i-d1-pinctrl";
+ reg = <0x2000000 0x800>;
+ interrupts = <SOC_PERIPHERAL_IRQ(69) IRQ_TYPE_LEVEL_HIGH>,
+ <SOC_PERIPHERAL_IRQ(71) IRQ_TYPE_LEVEL_HIGH>,
+ <SOC_PERIPHERAL_IRQ(73) IRQ_TYPE_LEVEL_HIGH>,
+ <SOC_PERIPHERAL_IRQ(75) IRQ_TYPE_LEVEL_HIGH>,
+ <SOC_PERIPHERAL_IRQ(77) IRQ_TYPE_LEVEL_HIGH>,
+ <SOC_PERIPHERAL_IRQ(79) IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_APB0>,
+ <&dcxo>,
+ <&rtc CLK_OSC32K>;
+ clock-names = "apb", "hosc", "losc";
+ gpio-controller;
+ interrupt-controller;
+ #gpio-cells = <3>;
+ #interrupt-cells = <3>;
+
+ /omit-if-no-ref/
+ can0_pins: can0-pins {
+ pins = "PB2", "PB3";
+ function = "can0";
+ };
+
+ /omit-if-no-ref/
+ can1_pins: can1-pins {
+ pins = "PB4", "PB5";
+ function = "can1";
+ };
+
+ /omit-if-no-ref/
+ clk_pg11_pin: clk-pg11-pin {
+ pins = "PG11";
+ function = "clk";
+ };
+
+ /omit-if-no-ref/
+ dsi_4lane_pins: dsi-4lane-pins {
+ pins = "PD0", "PD1", "PD2", "PD3", "PD4", "PD5",
+ "PD6", "PD7", "PD8", "PD9";
+ drive-strength = <30>;
+ function = "dsi";
+ };
+
+ /omit-if-no-ref/
+ lcd_rgb666_pins: lcd-rgb666-pins {
+ pins = "PD0", "PD1", "PD2", "PD3", "PD4", "PD5",
+ "PD6", "PD7", "PD8", "PD9", "PD10", "PD11",
+ "PD12", "PD13", "PD14", "PD15", "PD16", "PD17",
+ "PD18", "PD19", "PD20", "PD21";
+ function = "lcd0";
+ };
+
+ /omit-if-no-ref/
+ mmc0_pins: mmc0-pins {
+ pins = "PF0", "PF1", "PF2", "PF3", "PF4", "PF5";
+ function = "mmc0";
+ };
+
+ /omit-if-no-ref/
+ mmc1_pins: mmc1-pins {
+ pins = "PG0", "PG1", "PG2", "PG3", "PG4", "PG5";
+ function = "mmc1";
+ };
+
+ /omit-if-no-ref/
+ mmc2_pins: mmc2-pins {
+ pins = "PC2", "PC3", "PC4", "PC5", "PC6", "PC7";
+ function = "mmc2";
+ };
+
+ /omit-if-no-ref/
+ rgmii_pe_pins: rgmii-pe-pins {
+ pins = "PE0", "PE1", "PE2", "PE3", "PE4",
+ "PE5", "PE6", "PE7", "PE8", "PE9",
+ "PE11", "PE12", "PE13", "PE14", "PE15";
+ function = "emac";
+ };
+
+ /omit-if-no-ref/
+ rmii_pe_pins: rmii-pe-pins {
+ pins = "PE0", "PE1", "PE2", "PE3", "PE4",
+ "PE5", "PE6", "PE7", "PE8", "PE9";
+ function = "emac";
+ };
+
+ /omit-if-no-ref/
+ spi0_pins: spi0-pins {
+ pins = "PC2", "PC3", "PC4", "PC5";
+ function = "spi0";
+ };
+
+ /omit-if-no-ref/
+ uart1_pg6_pins: uart1-pg6-pins {
+ pins = "PG6", "PG7";
+ function = "uart1";
+ };
+
+ /omit-if-no-ref/
+ uart1_pg8_rts_cts_pins: uart1-pg8-rts-cts-pins {
+ pins = "PG8", "PG9";
+ function = "uart1";
+ };
+
+ /omit-if-no-ref/
+ uart3_pb_pins: uart3-pb-pins {
+ pins = "PB6", "PB7";
+ function = "uart3";
+ };
+ };
+
+ ccu: clock-controller@2001000 {
+ compatible = "allwinner,sun20i-d1-ccu";
+ reg = <0x2001000 0x1000>;
+ clocks = <&dcxo>,
+ <&rtc CLK_OSC32K>,
+ <&rtc CLK_IOSC>;
+ clock-names = "hosc", "losc", "iosc";
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ };
+
+ gpadc: adc@2009000 {
+ compatible = "allwinner,sun20i-d1-gpadc";
+ reg = <0x2009000 0x400>;
+ clocks = <&ccu CLK_BUS_GPADC>;
+ resets = <&ccu RST_BUS_GPADC>;
+ interrupts = <SOC_PERIPHERAL_IRQ(57) IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ #io-channel-cells = <1>;
+ };
+
+ dmic: dmic@2031000 {
+ compatible = "allwinner,sun20i-d1-dmic",
+ "allwinner,sun50i-h6-dmic";
+ reg = <0x2031000 0x400>;
+ interrupts = <SOC_PERIPHERAL_IRQ(24) IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_DMIC>,
+ <&ccu CLK_DMIC>;
+ clock-names = "bus", "mod";
+ resets = <&ccu RST_BUS_DMIC>;
+ dmas = <&dma 8>;
+ dma-names = "rx";
+ status = "disabled";
+ #sound-dai-cells = <0>;
+ };
+
+ i2s1: i2s@2033000 {
+ compatible = "allwinner,sun20i-d1-i2s",
+ "allwinner,sun50i-r329-i2s";
+ reg = <0x2033000 0x1000>;
+ interrupts = <SOC_PERIPHERAL_IRQ(27) IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_I2S1>,
+ <&ccu CLK_I2S1>;
+ clock-names = "apb", "mod";
+ resets = <&ccu RST_BUS_I2S1>;
+ dmas = <&dma 4>, <&dma 4>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ #sound-dai-cells = <0>;
+ };
+
+ i2s2: i2s@2034000 {
+ compatible = "allwinner,sun20i-d1-i2s",
+ "allwinner,sun50i-r329-i2s";
+ reg = <0x2034000 0x1000>;
+ interrupts = <SOC_PERIPHERAL_IRQ(28) IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_I2S2>,
+ <&ccu CLK_I2S2>;
+ clock-names = "apb", "mod";
+ resets = <&ccu RST_BUS_I2S2>;
+ dmas = <&dma 5>, <&dma 5>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ #sound-dai-cells = <0>;
+ };
+
+ timer: timer@2050000 {
+ compatible = "allwinner,sun20i-d1-timer",
+ "allwinner,sun8i-a23-timer";
+ reg = <0x2050000 0xa0>;
+ interrupts = <SOC_PERIPHERAL_IRQ(59) IRQ_TYPE_LEVEL_HIGH>,
+ <SOC_PERIPHERAL_IRQ(60) IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&dcxo>;
+ };
+
+ wdt: watchdog@20500a0 {
+ compatible = "allwinner,sun20i-d1-wdt-reset",
+ "allwinner,sun20i-d1-wdt";
+ reg = <0x20500a0 0x20>;
+ interrupts = <SOC_PERIPHERAL_IRQ(63) IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&dcxo>, <&rtc CLK_OSC32K>;
+ clock-names = "hosc", "losc";
+ status = "reserved";
+ };
+
+ uart0: serial@2500000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x2500000 0x400>;
+ reg-io-width = <4>;
+ reg-shift = <2>;
+ interrupts = <SOC_PERIPHERAL_IRQ(2) IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_UART0>;
+ resets = <&ccu RST_BUS_UART0>;
+ dmas = <&dma 14>, <&dma 14>;
+ dma-names = "tx", "rx";
+ status = "disabled";
+ };
+
+ uart1: serial@2500400 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x2500400 0x400>;
+ reg-io-width = <4>;
+ reg-shift = <2>;
+ interrupts = <SOC_PERIPHERAL_IRQ(3) IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_UART1>;
+ resets = <&ccu RST_BUS_UART1>;
+ dmas = <&dma 15>, <&dma 15>;
+ dma-names = "tx", "rx";
+ status = "disabled";
+ };
+
+ uart2: serial@2500800 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x2500800 0x400>;
+ reg-io-width = <4>;
+ reg-shift = <2>;
+ interrupts = <SOC_PERIPHERAL_IRQ(4) IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_UART2>;
+ resets = <&ccu RST_BUS_UART2>;
+ dmas = <&dma 16>, <&dma 16>;
+ dma-names = "tx", "rx";
+ status = "disabled";
+ };
+
+ uart3: serial@2500c00 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x2500c00 0x400>;
+ reg-io-width = <4>;
+ reg-shift = <2>;
+ interrupts = <SOC_PERIPHERAL_IRQ(5) IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_UART3>;
+ resets = <&ccu RST_BUS_UART3>;
+ dmas = <&dma 17>, <&dma 17>;
+ dma-names = "tx", "rx";
+ status = "disabled";
+ };
+
+ uart4: serial@2501000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x2501000 0x400>;
+ reg-io-width = <4>;
+ reg-shift = <2>;
+ interrupts = <SOC_PERIPHERAL_IRQ(6) IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_UART4>;
+ resets = <&ccu RST_BUS_UART4>;
+ dmas = <&dma 18>, <&dma 18>;
+ dma-names = "tx", "rx";
+ status = "disabled";
+ };
+
+ uart5: serial@2501400 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x2501400 0x400>;
+ reg-io-width = <4>;
+ reg-shift = <2>;
+ interrupts = <SOC_PERIPHERAL_IRQ(7) IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_UART5>;
+ resets = <&ccu RST_BUS_UART5>;
+ dmas = <&dma 19>, <&dma 19>;
+ dma-names = "tx", "rx";
+ status = "disabled";
+ };
+
+ i2c0: i2c@2502000 {
+ compatible = "allwinner,sun20i-d1-i2c",
+ "allwinner,sun8i-v536-i2c",
+ "allwinner,sun6i-a31-i2c";
+ reg = <0x2502000 0x400>;
+ interrupts = <SOC_PERIPHERAL_IRQ(9) IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_I2C0>;
+ resets = <&ccu RST_BUS_I2C0>;
+ dmas = <&dma 43>, <&dma 43>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c1: i2c@2502400 {
+ compatible = "allwinner,sun20i-d1-i2c",
+ "allwinner,sun8i-v536-i2c",
+ "allwinner,sun6i-a31-i2c";
+ reg = <0x2502400 0x400>;
+ interrupts = <SOC_PERIPHERAL_IRQ(10) IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_I2C1>;
+ resets = <&ccu RST_BUS_I2C1>;
+ dmas = <&dma 44>, <&dma 44>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c2: i2c@2502800 {
+ compatible = "allwinner,sun20i-d1-i2c",
+ "allwinner,sun8i-v536-i2c",
+ "allwinner,sun6i-a31-i2c";
+ reg = <0x2502800 0x400>;
+ interrupts = <SOC_PERIPHERAL_IRQ(11) IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_I2C2>;
+ resets = <&ccu RST_BUS_I2C2>;
+ dmas = <&dma 45>, <&dma 45>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c3: i2c@2502c00 {
+ compatible = "allwinner,sun20i-d1-i2c",
+ "allwinner,sun8i-v536-i2c",
+ "allwinner,sun6i-a31-i2c";
+ reg = <0x2502c00 0x400>;
+ interrupts = <SOC_PERIPHERAL_IRQ(12) IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_I2C3>;
+ resets = <&ccu RST_BUS_I2C3>;
+ dmas = <&dma 46>, <&dma 46>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ can0: can@2504000 {
+ compatible = "allwinner,sun20i-d1-can";
+ reg = <0x02504000 0x400>;
+ interrupts = <SOC_PERIPHERAL_IRQ(21) IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_CAN0>;
+ resets = <&ccu RST_BUS_CAN0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&can0_pins>;
+ status = "disabled";
+ };
+
+ can1: can@2504400 {
+ compatible = "allwinner,sun20i-d1-can";
+ reg = <0x02504400 0x400>;
+ interrupts = <SOC_PERIPHERAL_IRQ(22) IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_CAN1>;
+ resets = <&ccu RST_BUS_CAN1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&can1_pins>;
+ status = "disabled";
+ };
+
+ syscon: syscon@3000000 {
+ compatible = "allwinner,sun20i-d1-system-control";
+ reg = <0x3000000 0x1000>;
+ ranges;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ };
+
+ dma: dma-controller@3002000 {
+ compatible = "allwinner,sun20i-d1-dma";
+ reg = <0x3002000 0x1000>;
+ interrupts = <SOC_PERIPHERAL_IRQ(50) IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_DMA>, <&ccu CLK_MBUS_DMA>;
+ clock-names = "bus", "mbus";
+ resets = <&ccu RST_BUS_DMA>;
+ dma-channels = <16>;
+ dma-requests = <48>;
+ #dma-cells = <1>;
+ };
+
+ sid: efuse@3006000 {
+ compatible = "allwinner,sun20i-d1-sid";
+ reg = <0x3006000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ };
+
+ crypto: crypto@3040000 {
+ compatible = "allwinner,sun20i-d1-crypto";
+ reg = <0x3040000 0x800>;
+ interrupts = <SOC_PERIPHERAL_IRQ(52) IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_CE>,
+ <&ccu CLK_CE>,
+ <&ccu CLK_MBUS_CE>,
+ <&rtc CLK_IOSC>;
+ clock-names = "bus", "mod", "ram", "trng";
+ resets = <&ccu RST_BUS_CE>;
+ };
+
+ mbus: dram-controller@3102000 {
+ compatible = "allwinner,sun20i-d1-mbus";
+ reg = <0x3102000 0x1000>,
+ <0x3103000 0x1000>;
+ reg-names = "mbus", "dram";
+ interrupts = <SOC_PERIPHERAL_IRQ(43) IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_MBUS>,
+ <&ccu CLK_DRAM>,
+ <&ccu CLK_BUS_DRAM>;
+ clock-names = "mbus", "dram", "bus";
+ dma-ranges = <0 0x40000000 0x80000000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ #interconnect-cells = <1>;
+ };
+
+ mmc0: mmc@4020000 {
+ compatible = "allwinner,sun20i-d1-mmc";
+ reg = <0x4020000 0x1000>;
+ interrupts = <SOC_PERIPHERAL_IRQ(40) IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_MMC0>, <&ccu CLK_MMC0>;
+ clock-names = "ahb", "mmc";
+ resets = <&ccu RST_BUS_MMC0>;
+ reset-names = "ahb";
+ cap-sd-highspeed;
+ max-frequency = <150000000>;
+ no-mmc;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mmc1: mmc@4021000 {
+ compatible = "allwinner,sun20i-d1-mmc";
+ reg = <0x4021000 0x1000>;
+ interrupts = <SOC_PERIPHERAL_IRQ(41) IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_MMC1>, <&ccu CLK_MMC1>;
+ clock-names = "ahb", "mmc";
+ resets = <&ccu RST_BUS_MMC1>;
+ reset-names = "ahb";
+ cap-sd-highspeed;
+ max-frequency = <150000000>;
+ no-mmc;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mmc2: mmc@4022000 {
+ compatible = "allwinner,sun20i-d1-emmc",
+ "allwinner,sun50i-a100-emmc";
+ reg = <0x4022000 0x1000>;
+ interrupts = <SOC_PERIPHERAL_IRQ(42) IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_MMC2>, <&ccu CLK_MMC2>;
+ clock-names = "ahb", "mmc";
+ resets = <&ccu RST_BUS_MMC2>;
+ reset-names = "ahb";
+ cap-mmc-highspeed;
+ max-frequency = <150000000>;
+ mmc-ddr-1_8v;
+ mmc-ddr-3_3v;
+ no-sd;
+ no-sdio;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ spi0: spi@4025000 {
+ compatible = "allwinner,sun20i-d1-spi",
+ "allwinner,sun50i-r329-spi";
+ reg = <0x04025000 0x1000>;
+ interrupts = <SOC_PERIPHERAL_IRQ(15) IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_SPI0>, <&ccu CLK_SPI0>;
+ clock-names = "ahb", "mod";
+ dmas = <&dma 22>, <&dma 22>;
+ dma-names = "rx", "tx";
+ resets = <&ccu RST_BUS_SPI0>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ spi1: spi@4026000 {
+ compatible = "allwinner,sun20i-d1-spi-dbi",
+ "allwinner,sun50i-r329-spi-dbi",
+ "allwinner,sun50i-r329-spi";
+ reg = <0x04026000 0x1000>;
+ interrupts = <SOC_PERIPHERAL_IRQ(16) IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_SPI1>, <&ccu CLK_SPI1>;
+ clock-names = "ahb", "mod";
+ dmas = <&dma 23>, <&dma 23>;
+ dma-names = "rx", "tx";
+ resets = <&ccu RST_BUS_SPI1>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ usb_otg: usb@4100000 {
+ compatible = "allwinner,sun20i-d1-musb",
+ "allwinner,sun8i-a33-musb";
+ reg = <0x4100000 0x400>;
+ interrupts = <SOC_PERIPHERAL_IRQ(29) IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "mc";
+ clocks = <&ccu CLK_BUS_OTG>;
+ resets = <&ccu RST_BUS_OTG>;
+ extcon = <&usbphy 0>;
+ phys = <&usbphy 0>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ usbphy: phy@4100400 {
+ compatible = "allwinner,sun20i-d1-usb-phy";
+ reg = <0x4100400 0x100>,
+ <0x4101800 0x100>,
+ <0x4200800 0x100>;
+ reg-names = "phy_ctrl",
+ "pmu0",
+ "pmu1";
+ clocks = <&dcxo>,
+ <&dcxo>;
+ clock-names = "usb0_phy",
+ "usb1_phy";
+ resets = <&ccu RST_USB_PHY0>,
+ <&ccu RST_USB_PHY1>;
+ reset-names = "usb0_reset",
+ "usb1_reset";
+ status = "disabled";
+ #phy-cells = <1>;
+ };
+
+ ehci0: usb@4101000 {
+ compatible = "allwinner,sun20i-d1-ehci",
+ "generic-ehci";
+ reg = <0x4101000 0x100>;
+ interrupts = <SOC_PERIPHERAL_IRQ(30) IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_OHCI0>,
+ <&ccu CLK_BUS_EHCI0>,
+ <&ccu CLK_USB_OHCI0>;
+ resets = <&ccu RST_BUS_OHCI0>,
+ <&ccu RST_BUS_EHCI0>;
+ phys = <&usbphy 0>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ ohci0: usb@4101400 {
+ compatible = "allwinner,sun20i-d1-ohci",
+ "generic-ohci";
+ reg = <0x4101400 0x100>;
+ interrupts = <SOC_PERIPHERAL_IRQ(31) IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_OHCI0>,
+ <&ccu CLK_USB_OHCI0>;
+ resets = <&ccu RST_BUS_OHCI0>;
+ phys = <&usbphy 0>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ ehci1: usb@4200000 {
+ compatible = "allwinner,sun20i-d1-ehci",
+ "generic-ehci";
+ reg = <0x4200000 0x100>;
+ interrupts = <SOC_PERIPHERAL_IRQ(33) IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_OHCI1>,
+ <&ccu CLK_BUS_EHCI1>,
+ <&ccu CLK_USB_OHCI1>;
+ resets = <&ccu RST_BUS_OHCI1>,
+ <&ccu RST_BUS_EHCI1>;
+ phys = <&usbphy 1>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ ohci1: usb@4200400 {
+ compatible = "allwinner,sun20i-d1-ohci",
+ "generic-ohci";
+ reg = <0x4200400 0x100>;
+ interrupts = <SOC_PERIPHERAL_IRQ(34) IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_OHCI1>,
+ <&ccu CLK_USB_OHCI1>;
+ resets = <&ccu RST_BUS_OHCI1>;
+ phys = <&usbphy 1>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ emac: ethernet@4500000 {
+ compatible = "allwinner,sun20i-d1-emac",
+ "allwinner,sun50i-a64-emac";
+ reg = <0x4500000 0x10000>;
+ interrupts = <SOC_PERIPHERAL_IRQ(46) IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "macirq";
+ clocks = <&ccu CLK_BUS_EMAC>;
+ clock-names = "stmmaceth";
+ resets = <&ccu RST_BUS_EMAC>;
+ reset-names = "stmmaceth";
+ syscon = <&syscon>;
+ status = "disabled";
+
+ mdio: mdio {
+ compatible = "snps,dwmac-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ };
+
+ display_clocks: clock-controller@5000000 {
+ compatible = "allwinner,sun20i-d1-de2-clk",
+ "allwinner,sun50i-h5-de2-clk";
+ reg = <0x5000000 0x10000>;
+ clocks = <&ccu CLK_BUS_DE>, <&ccu CLK_DE>;
+ clock-names = "bus", "mod";
+ resets = <&ccu RST_BUS_DE>;
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ };
+
+ mixer0: mixer@5100000 {
+ compatible = "allwinner,sun20i-d1-de2-mixer-0";
+ reg = <0x5100000 0x100000>;
+ clocks = <&display_clocks CLK_BUS_MIXER0>,
+ <&display_clocks CLK_MIXER0>;
+ clock-names = "bus", "mod";
+ resets = <&display_clocks RST_MIXER0>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ mixer0_out: port@1 {
+ reg = <1>;
+
+ mixer0_out_tcon_top_mixer0: endpoint {
+ remote-endpoint = <&tcon_top_mixer0_in_mixer0>;
+ };
+ };
+ };
+ };
+
+ mixer1: mixer@5200000 {
+ compatible = "allwinner,sun20i-d1-de2-mixer-1";
+ reg = <0x5200000 0x100000>;
+ clocks = <&display_clocks CLK_BUS_MIXER1>,
+ <&display_clocks CLK_MIXER1>;
+ clock-names = "bus", "mod";
+ resets = <&display_clocks RST_MIXER1>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ mixer1_out: port@1 {
+ reg = <1>;
+
+ mixer1_out_tcon_top_mixer1: endpoint {
+ remote-endpoint = <&tcon_top_mixer1_in_mixer1>;
+ };
+ };
+ };
+ };
+
+ dsi: dsi@5450000 {
+ compatible = "allwinner,sun20i-d1-mipi-dsi",
+ "allwinner,sun50i-a100-mipi-dsi";
+ reg = <0x5450000 0x1000>;
+ interrupts = <SOC_PERIPHERAL_IRQ(92) IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_MIPI_DSI>,
+ <&tcon_top CLK_TCON_TOP_DSI>;
+ clock-names = "bus", "mod";
+ resets = <&ccu RST_BUS_MIPI_DSI>;
+ phys = <&dphy>;
+ phy-names = "dphy";
+ status = "disabled";
+
+ port {
+ dsi_in_tcon_lcd0: endpoint {
+ remote-endpoint = <&tcon_lcd0_out_dsi>;
+ };
+ };
+ };
+
+ dphy: phy@5451000 {
+ compatible = "allwinner,sun20i-d1-mipi-dphy",
+ "allwinner,sun50i-a100-mipi-dphy";
+ reg = <0x5451000 0x1000>;
+ interrupts = <SOC_PERIPHERAL_IRQ(92) IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_MIPI_DSI>,
+ <&ccu CLK_MIPI_DSI>;
+ clock-names = "bus", "mod";
+ resets = <&ccu RST_BUS_MIPI_DSI>;
+ #phy-cells = <0>;
+ };
+
+ tcon_top: tcon-top@5460000 {
+ compatible = "allwinner,sun20i-d1-tcon-top";
+ reg = <0x5460000 0x1000>;
+ clocks = <&ccu CLK_BUS_DPSS_TOP>,
+ <&ccu CLK_TCON_TV>,
+ <&ccu CLK_TVE>,
+ <&ccu CLK_TCON_LCD0>;
+ clock-names = "bus", "tcon-tv0", "tve0", "dsi";
+ clock-output-names = "tcon-top-tv0", "tcon-top-dsi";
+ resets = <&ccu RST_BUS_DPSS_TOP>;
+ #clock-cells = <1>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ tcon_top_mixer0_in: port@0 {
+ reg = <0>;
+
+ tcon_top_mixer0_in_mixer0: endpoint {
+ remote-endpoint = <&mixer0_out_tcon_top_mixer0>;
+ };
+ };
+
+ tcon_top_mixer0_out: port@1 {
+ reg = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ tcon_top_mixer0_out_tcon_lcd0: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&tcon_lcd0_in_tcon_top_mixer0>;
+ };
+
+ tcon_top_mixer0_out_tcon_tv0: endpoint@2 {
+ reg = <2>;
+ remote-endpoint = <&tcon_tv0_in_tcon_top_mixer0>;
+ };
+ };
+
+ tcon_top_mixer1_in: port@2 {
+ reg = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ tcon_top_mixer1_in_mixer1: endpoint@1 {
+ reg = <1>;
+ remote-endpoint = <&mixer1_out_tcon_top_mixer1>;
+ };
+ };
+
+ tcon_top_mixer1_out: port@3 {
+ reg = <3>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ tcon_top_mixer1_out_tcon_lcd0: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&tcon_lcd0_in_tcon_top_mixer1>;
+ };
+
+ tcon_top_mixer1_out_tcon_tv0: endpoint@2 {
+ reg = <2>;
+ remote-endpoint = <&tcon_tv0_in_tcon_top_mixer1>;
+ };
+ };
+
+ tcon_top_hdmi_in: port@4 {
+ reg = <4>;
+
+ tcon_top_hdmi_in_tcon_tv0: endpoint {
+ remote-endpoint = <&tcon_tv0_out_tcon_top_hdmi>;
+ };
+ };
+
+ tcon_top_hdmi_out: port@5 {
+ reg = <5>;
+ };
+ };
+ };
+
+ tcon_lcd0: lcd-controller@5461000 {
+ compatible = "allwinner,sun20i-d1-tcon-lcd";
+ reg = <0x5461000 0x1000>;
+ interrupts = <SOC_PERIPHERAL_IRQ(90) IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_TCON_LCD0>,
+ <&ccu CLK_TCON_LCD0>;
+ clock-names = "ahb", "tcon-ch0";
+ clock-output-names = "tcon-pixel-clock";
+ resets = <&ccu RST_BUS_TCON_LCD0>,
+ <&ccu RST_BUS_LVDS0>;
+ reset-names = "lcd", "lvds";
+ #clock-cells = <0>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ tcon_lcd0_in: port@0 {
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ tcon_lcd0_in_tcon_top_mixer0: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&tcon_top_mixer0_out_tcon_lcd0>;
+ };
+
+ tcon_lcd0_in_tcon_top_mixer1: endpoint@1 {
+ reg = <1>;
+ remote-endpoint = <&tcon_top_mixer1_out_tcon_lcd0>;
+ };
+ };
+
+ tcon_lcd0_out: port@1 {
+ reg = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ tcon_lcd0_out_dsi: endpoint@1 {
+ reg = <1>;
+ remote-endpoint = <&dsi_in_tcon_lcd0>;
+ };
+ };
+ };
+ };
+
+ tcon_tv0: lcd-controller@5470000 {
+ compatible = "allwinner,sun20i-d1-tcon-tv";
+ reg = <0x5470000 0x1000>;
+ interrupts = <SOC_PERIPHERAL_IRQ(91) IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_TCON_TV>,
+ <&tcon_top CLK_TCON_TOP_TV0>;
+ clock-names = "ahb", "tcon-ch1";
+ resets = <&ccu RST_BUS_TCON_TV>;
+ reset-names = "lcd";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ tcon_tv0_in: port@0 {
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ tcon_tv0_in_tcon_top_mixer0: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&tcon_top_mixer0_out_tcon_tv0>;
+ };
+
+ tcon_tv0_in_tcon_top_mixer1: endpoint@1 {
+ reg = <1>;
+ remote-endpoint = <&tcon_top_mixer1_out_tcon_tv0>;
+ };
+ };
+
+ tcon_tv0_out: port@1 {
+ reg = <1>;
+
+ tcon_tv0_out_tcon_top_hdmi: endpoint {
+ remote-endpoint = <&tcon_top_hdmi_in_tcon_tv0>;
+ };
+ };
+ };
+ };
+
+ ppu: power-controller@7001000 {
+ compatible = "allwinner,sun20i-d1-ppu";
+ reg = <0x7001000 0x1000>;
+ clocks = <&r_ccu CLK_BUS_R_PPU>;
+ resets = <&r_ccu RST_BUS_R_PPU>;
+ #power-domain-cells = <1>;
+ };
+
+ r_ccu: clock-controller@7010000 {
+ compatible = "allwinner,sun20i-d1-r-ccu";
+ reg = <0x7010000 0x400>;
+ clocks = <&dcxo>,
+ <&rtc CLK_OSC32K>,
+ <&rtc CLK_IOSC>,
+ <&ccu CLK_PLL_PERIPH0_DIV3>;
+ clock-names = "hosc", "losc", "iosc", "pll-periph";
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ };
+
+ rtc: rtc@7090000 {
+ compatible = "allwinner,sun20i-d1-rtc",
+ "allwinner,sun50i-r329-rtc";
+ reg = <0x7090000 0x400>;
+ interrupts = <SOC_PERIPHERAL_IRQ(144) IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&r_ccu CLK_BUS_R_RTC>,
+ <&dcxo>,
+ <&r_ccu CLK_R_AHB>;
+ clock-names = "bus", "hosc", "ahb";
+ #clock-cells = <1>;
+ };
+ };
+};
diff --git a/include/dt-bindings/clock/sun20i-d1-ccu.h b/include/dt-bindings/clock/sun20i-d1-ccu.h
new file mode 100644
index 00000000000..fdbfb404f92
--- /dev/null
+++ b/include/dt-bindings/clock/sun20i-d1-ccu.h
@@ -0,0 +1,158 @@
+/* SPDX-License-Identifier: (GPL-2.0+ OR MIT) */
+/*
+ * Copyright (C) 2020 huangzhenwei@allwinnertech.com
+ * Copyright (C) 2021 Samuel Holland <samuel@sholland.org>
+ */
+
+#ifndef _DT_BINDINGS_CLK_SUN20I_D1_CCU_H_
+#define _DT_BINDINGS_CLK_SUN20I_D1_CCU_H_
+
+#define CLK_PLL_CPUX 0
+#define CLK_PLL_DDR0 1
+#define CLK_PLL_PERIPH0_4X 2
+#define CLK_PLL_PERIPH0_2X 3
+#define CLK_PLL_PERIPH0_800M 4
+#define CLK_PLL_PERIPH0 5
+#define CLK_PLL_PERIPH0_DIV3 6
+#define CLK_PLL_VIDEO0_4X 7
+#define CLK_PLL_VIDEO0_2X 8
+#define CLK_PLL_VIDEO0 9
+#define CLK_PLL_VIDEO1_4X 10
+#define CLK_PLL_VIDEO1_2X 11
+#define CLK_PLL_VIDEO1 12
+#define CLK_PLL_VE 13
+#define CLK_PLL_AUDIO0_4X 14
+#define CLK_PLL_AUDIO0_2X 15
+#define CLK_PLL_AUDIO0 16
+#define CLK_PLL_AUDIO1 17
+#define CLK_PLL_AUDIO1_DIV2 18
+#define CLK_PLL_AUDIO1_DIV5 19
+#define CLK_CPUX 20
+#define CLK_CPUX_AXI 21
+#define CLK_CPUX_APB 22
+#define CLK_PSI_AHB 23
+#define CLK_APB0 24
+#define CLK_APB1 25
+#define CLK_MBUS 26
+#define CLK_DE 27
+#define CLK_BUS_DE 28
+#define CLK_DI 29
+#define CLK_BUS_DI 30
+#define CLK_G2D 31
+#define CLK_BUS_G2D 32
+#define CLK_CE 33
+#define CLK_BUS_CE 34
+#define CLK_VE 35
+#define CLK_BUS_VE 36
+#define CLK_BUS_DMA 37
+#define CLK_BUS_MSGBOX0 38
+#define CLK_BUS_MSGBOX1 39
+#define CLK_BUS_MSGBOX2 40
+#define CLK_BUS_SPINLOCK 41
+#define CLK_BUS_HSTIMER 42
+#define CLK_AVS 43
+#define CLK_BUS_DBG 44
+#define CLK_BUS_PWM 45
+#define CLK_BUS_IOMMU 46
+#define CLK_DRAM 47
+#define CLK_MBUS_DMA 48
+#define CLK_MBUS_VE 49
+#define CLK_MBUS_CE 50
+#define CLK_MBUS_TVIN 51
+#define CLK_MBUS_CSI 52
+#define CLK_MBUS_G2D 53
+#define CLK_MBUS_RISCV 54
+#define CLK_BUS_DRAM 55
+#define CLK_MMC0 56
+#define CLK_MMC1 57
+#define CLK_MMC2 58
+#define CLK_BUS_MMC0 59
+#define CLK_BUS_MMC1 60
+#define CLK_BUS_MMC2 61
+#define CLK_BUS_UART0 62
+#define CLK_BUS_UART1 63
+#define CLK_BUS_UART2 64
+#define CLK_BUS_UART3 65
+#define CLK_BUS_UART4 66
+#define CLK_BUS_UART5 67
+#define CLK_BUS_I2C0 68
+#define CLK_BUS_I2C1 69
+#define CLK_BUS_I2C2 70
+#define CLK_BUS_I2C3 71
+#define CLK_SPI0 72
+#define CLK_SPI1 73
+#define CLK_BUS_SPI0 74
+#define CLK_BUS_SPI1 75
+#define CLK_EMAC_25M 76
+#define CLK_BUS_EMAC 77
+#define CLK_IR_TX 78
+#define CLK_BUS_IR_TX 79
+#define CLK_BUS_GPADC 80
+#define CLK_BUS_THS 81
+#define CLK_I2S0 82
+#define CLK_I2S1 83
+#define CLK_I2S2 84
+#define CLK_I2S2_ASRC 85
+#define CLK_BUS_I2S0 86
+#define CLK_BUS_I2S1 87
+#define CLK_BUS_I2S2 88
+#define CLK_SPDIF_TX 89
+#define CLK_SPDIF_RX 90
+#define CLK_BUS_SPDIF 91
+#define CLK_DMIC 92
+#define CLK_BUS_DMIC 93
+#define CLK_AUDIO_DAC 94
+#define CLK_AUDIO_ADC 95
+#define CLK_BUS_AUDIO 96
+#define CLK_USB_OHCI0 97
+#define CLK_USB_OHCI1 98
+#define CLK_BUS_OHCI0 99
+#define CLK_BUS_OHCI1 100
+#define CLK_BUS_EHCI0 101
+#define CLK_BUS_EHCI1 102
+#define CLK_BUS_OTG 103
+#define CLK_BUS_LRADC 104
+#define CLK_BUS_DPSS_TOP 105
+#define CLK_HDMI_24M 106
+#define CLK_HDMI_CEC_32K 107
+#define CLK_HDMI_CEC 108
+#define CLK_BUS_HDMI 109
+#define CLK_MIPI_DSI 110
+#define CLK_BUS_MIPI_DSI 111
+#define CLK_TCON_LCD0 112
+#define CLK_BUS_TCON_LCD0 113
+#define CLK_TCON_TV 114
+#define CLK_BUS_TCON_TV 115
+#define CLK_TVE 116
+#define CLK_BUS_TVE_TOP 117
+#define CLK_BUS_TVE 118
+#define CLK_TVD 119
+#define CLK_BUS_TVD_TOP 120
+#define CLK_BUS_TVD 121
+#define CLK_LEDC 122
+#define CLK_BUS_LEDC 123
+#define CLK_CSI_TOP 124
+#define CLK_CSI_MCLK 125
+#define CLK_BUS_CSI 126
+#define CLK_TPADC 127
+#define CLK_BUS_TPADC 128
+#define CLK_BUS_TZMA 129
+#define CLK_DSP 130
+#define CLK_BUS_DSP_CFG 131
+#define CLK_RISCV 132
+#define CLK_RISCV_AXI 133
+#define CLK_BUS_RISCV_CFG 134
+#define CLK_FANOUT_24M 135
+#define CLK_FANOUT_12M 136
+#define CLK_FANOUT_16M 137
+#define CLK_FANOUT_25M 138
+#define CLK_FANOUT_32K 139
+#define CLK_FANOUT_27M 140
+#define CLK_FANOUT_PCLK 141
+#define CLK_FANOUT0 142
+#define CLK_FANOUT1 143
+#define CLK_FANOUT2 144
+#define CLK_BUS_CAN0 145
+#define CLK_BUS_CAN1 146
+
+#endif /* _DT_BINDINGS_CLK_SUN20I_D1_CCU_H_ */
diff --git a/include/dt-bindings/clock/sun20i-d1-r-ccu.h b/include/dt-bindings/clock/sun20i-d1-r-ccu.h
new file mode 100644
index 00000000000..f95c170711e
--- /dev/null
+++ b/include/dt-bindings/clock/sun20i-d1-r-ccu.h
@@ -0,0 +1,19 @@
+/* SPDX-License-Identifier: (GPL-2.0+ OR MIT) */
+/*
+ * Copyright (C) 2021 Samuel Holland <samuel@sholland.org>
+ */
+
+#ifndef _DT_BINDINGS_CLK_SUN20I_D1_R_CCU_H_
+#define _DT_BINDINGS_CLK_SUN20I_D1_R_CCU_H_
+
+#define CLK_R_AHB 0
+
+#define CLK_BUS_R_TIMER 2
+#define CLK_BUS_R_TWD 3
+#define CLK_BUS_R_PPU 4
+#define CLK_R_IR_RX 5
+#define CLK_BUS_R_IR_RX 6
+#define CLK_BUS_R_RTC 7
+#define CLK_BUS_R_CPUCFG 8
+
+#endif /* _DT_BINDINGS_CLK_SUN20I_D1_R_CCU_H_ */
diff --git a/include/dt-bindings/reset/sun20i-d1-ccu.h b/include/dt-bindings/reset/sun20i-d1-ccu.h
new file mode 100644
index 00000000000..79e52aca591
--- /dev/null
+++ b/include/dt-bindings/reset/sun20i-d1-ccu.h
@@ -0,0 +1,79 @@
+/* SPDX-License-Identifier: (GPL-2.0+ OR MIT) */
+/*
+ * Copyright (c) 2020 huangzhenwei@allwinnertech.com
+ * Copyright (C) 2021 Samuel Holland <samuel@sholland.org>
+ */
+
+#ifndef _DT_BINDINGS_RST_SUN20I_D1_CCU_H_
+#define _DT_BINDINGS_RST_SUN20I_D1_CCU_H_
+
+#define RST_MBUS 0
+#define RST_BUS_DE 1
+#define RST_BUS_DI 2
+#define RST_BUS_G2D 3
+#define RST_BUS_CE 4
+#define RST_BUS_VE 5
+#define RST_BUS_DMA 6
+#define RST_BUS_MSGBOX0 7
+#define RST_BUS_MSGBOX1 8
+#define RST_BUS_MSGBOX2 9
+#define RST_BUS_SPINLOCK 10
+#define RST_BUS_HSTIMER 11
+#define RST_BUS_DBG 12
+#define RST_BUS_PWM 13
+#define RST_BUS_DRAM 14
+#define RST_BUS_MMC0 15
+#define RST_BUS_MMC1 16
+#define RST_BUS_MMC2 17
+#define RST_BUS_UART0 18
+#define RST_BUS_UART1 19
+#define RST_BUS_UART2 20
+#define RST_BUS_UART3 21
+#define RST_BUS_UART4 22
+#define RST_BUS_UART5 23
+#define RST_BUS_I2C0 24
+#define RST_BUS_I2C1 25
+#define RST_BUS_I2C2 26
+#define RST_BUS_I2C3 27
+#define RST_BUS_SPI0 28
+#define RST_BUS_SPI1 29
+#define RST_BUS_EMAC 30
+#define RST_BUS_IR_TX 31
+#define RST_BUS_GPADC 32
+#define RST_BUS_THS 33
+#define RST_BUS_I2S0 34
+#define RST_BUS_I2S1 35
+#define RST_BUS_I2S2 36
+#define RST_BUS_SPDIF 37
+#define RST_BUS_DMIC 38
+#define RST_BUS_AUDIO 39
+#define RST_USB_PHY0 40
+#define RST_USB_PHY1 41
+#define RST_BUS_OHCI0 42
+#define RST_BUS_OHCI1 43
+#define RST_BUS_EHCI0 44
+#define RST_BUS_EHCI1 45
+#define RST_BUS_OTG 46
+#define RST_BUS_LRADC 47
+#define RST_BUS_DPSS_TOP 48
+#define RST_BUS_HDMI_SUB 49
+#define RST_BUS_HDMI_MAIN 50
+#define RST_BUS_MIPI_DSI 51
+#define RST_BUS_TCON_LCD0 52
+#define RST_BUS_TCON_TV 53
+#define RST_BUS_LVDS0 54
+#define RST_BUS_TVE 55
+#define RST_BUS_TVE_TOP 56
+#define RST_BUS_TVD 57
+#define RST_BUS_TVD_TOP 58
+#define RST_BUS_LEDC 59
+#define RST_BUS_CSI 60
+#define RST_BUS_TPADC 61
+#define RST_DSP 62
+#define RST_BUS_DSP_CFG 63
+#define RST_BUS_DSP_DBG 64
+#define RST_BUS_RISCV_CFG 65
+#define RST_BUS_CAN0 66
+#define RST_BUS_CAN1 67
+
+#endif /* _DT_BINDINGS_RST_SUN20I_D1_CCU_H_ */
diff --git a/include/dt-bindings/reset/sun20i-d1-r-ccu.h b/include/dt-bindings/reset/sun20i-d1-r-ccu.h
new file mode 100644
index 00000000000..e20babc990a
--- /dev/null
+++ b/include/dt-bindings/reset/sun20i-d1-r-ccu.h
@@ -0,0 +1,16 @@
+/* SPDX-License-Identifier: (GPL-2.0+ OR MIT) */
+/*
+ * Copyright (C) 2021 Samuel Holland <samuel@sholland.org>
+ */
+
+#ifndef _DT_BINDINGS_RST_SUN20I_D1_R_CCU_H_
+#define _DT_BINDINGS_RST_SUN20I_D1_R_CCU_H_
+
+#define RST_BUS_R_TIMER 0
+#define RST_BUS_R_TWD 1
+#define RST_BUS_R_PPU 2
+#define RST_BUS_R_IR_RX 3
+#define RST_BUS_R_RTC 4
+#define RST_BUS_R_CPUCFG 5
+
+#endif /* _DT_BINDINGS_RST_SUN20I_D1_R_CCU_H_ */
--
2.35.8
^ permalink raw reply related [flat|nested] 5+ messages in thread