Re: [PATCH v2 00/10] ARM: dts: suniv: F1C100s: add more peripherals

["Jernej Škrabec" <jernej.skrabec@gmail.com>]

Dne ponedeljek, 07. november 2022 ob 01:54:23 CET je Andre Przywara 
napisal(a):
> This is a fixed version of the initial post. I dropped the two patches
> that were already applied by the respective maintainers, and fixed the
> smaller issues mentioned in the review.
> This adds v2 of the series enabling the "Lctech Pi F1C200s" board on top,
> also with the comments addressed.

Please don't combine series if not agreed upon before. Now whole series will 
be delayed until USB is sorted out.

Best regards,
Jernej

> The whole series goes on top of v3 of Icenowy's F1C100s USB support
> series [1]. There is no real conflict, but the lctech-pi.dts file
> references the new USB DT nodes from the .dtsi.
> 
> I put a git repo with all those patches up here:
> https://github.com/apritzel/linux/commits/f1c100s-devices-v2
> 
> For a changelog see below.
> 
> [1]
> https://lore.kernel.org/linux-arm-kernel/20221106154826.6687-1-andre.przywa
> ra@arm.com/T/#t
> 
> =================
> The Allwinner F1C100s series of SoCs shares many peripherals with other
> Allwinner SoCs. Since they are compatible, we can use the existing
> drivers, and just need to enable the devices in the DT.
> 
> This series adds the I2C controllers, the PWM device, the CIR (infrared)
> device and the LRADC (aka. KEYADC, low res ADC) to the F1C100s .dtsi, so
> boards can just use them by setting 'status = "okay";'.
> 
> The only thing missing driver-wise is the IR mod clock, which was not
> modeled in our CCU driver. Patch 4/10 fixes that.
> 
> For every device there is one patch that adds the new compatible string
> to the DT binding, and another patch to add the DT node.
> 
> This has been tested on the Lctech Pi F1C200s board, by:
> - Connecting an LED to PE6, and configuring this as the PWM pin in the DT.
>   Doing a sweep on /sys/class/pwm/pwm1/duty_cycle made the LED fade out.
> - Configuring PD0/PD12 as I2C0, and letting i2c-detect find the on-board
>   NS2009 I2C chip.
> - Connecting two resistors to the "ADC" pin, and configuring them as two
>   buttons in the DT. /dev/input/event0 properly reported button presses.
> - Connecting an infrared receiver to PE11, configured as CIR.
>   ir-keytable reported key presses on a remote control.
> 
> All those (basic) tests were successful, and prove that the peripherals
> do work and are compatible.
> 
> The final three patches add the binding docs and the .dts file for the
> Lctech Pi F1C200s development board.
> 
> Please have a look and test on your hardware, if possible.
> 
> Cheers,
> Andre
> 
> Changelog v1 ... v2:
> - dropped former patch 3/9 and 8/9: already applied
> - increase register frame size in DT for PWM and LRADC
> - drop I2C1 pins from pinctroller DT node
> - increase IR mod clock mux to 2 bits
> - fix mistyped comma in vendor prefix name
> - drop unneeded mmc0 and spi0 aliases from Lctech Pi DT
> - add /omit-if-no-ref/ tag to UART1 pins
> - add ACKs and Reviewed-by tags
> 
> 
> Andre Przywara (10):
>   dt-bindings: pwm: allwinner,sun4i-a10: Add F1C100s compatible
>   ARM: dts: suniv: f1c100s: add PWM node
>   ARM: dts: suniv: f1c100s: add I2C DT nodes
>   clk: sunxi-ng: f1c100s: Add IR mod clock
>   dt-bindings: media: IR: Add F1C100s IR compatible string
>   ARM: dts: suniv: f1c100s: add CIR DT node
>   ARM: dts: suniv: f1c100s: add LRADC node
>   dt-bindings: vendor-prefixes: add Lctech name
>   dt-bindings: arm: sunxi: add compatible strings for Lctech Pi
>   ARM: dts: suniv: Add Lctech Pi F1C200s devicetree
> 
>  .../devicetree/bindings/arm/sunxi.yaml        |  6 ++
>  .../media/allwinner,sun4i-a10-ir.yaml         |  1 +
>  .../bindings/pwm/allwinner,sun4i-a10-pwm.yaml |  4 +-
>  .../devicetree/bindings/vendor-prefixes.yaml  |  2 +
>  arch/arm/boot/dts/Makefile                    |  1 +
>  arch/arm/boot/dts/suniv-f1c100s.dtsi          | 76 ++++++++++++++++++
>  arch/arm/boot/dts/suniv-f1c200s-lctech-pi.dts | 78 +++++++++++++++++++
>  drivers/clk/sunxi-ng/ccu-suniv-f1c100s.c      | 11 ++-
>  drivers/clk/sunxi-ng/ccu-suniv-f1c100s.h      |  2 +-
>  include/dt-bindings/clock/suniv-ccu-f1c100s.h |  2 +
>  10 files changed, 180 insertions(+), 3 deletions(-)
>  create mode 100644 arch/arm/boot/dts/suniv-f1c200s-lctech-pi.dts
> 
> --
> 2.35.5