From: Adrian Hunter <adrian.hunter@intel.com>
To: Tanmay Kathpalia <tanmay.kathpalia@altera.com>,
<linux-mmc@vger.kernel.org>
Cc: <ulf.hansson@linaro.org>, Ulf Hansson <ulfh@kernel.org>,
Philipp Zabel <p.zabel@pengutronix.de>,
<linux-kernel@vger.kernel.org>
Subject: Re: [PATCH v2 9/9] mmc: sdhci-cadence: add Altera Agilex5 SD6HC support
Date: Sat, 4 Jul 2026 14:18:33 +0300 [thread overview]
Message-ID: <1c57e707-dd72-499a-88c9-8129da28bf74@intel.com> (raw)
In-Reply-To: <20260627201457.12318-10-tanmay.kathpalia@altera.com>
On 27/06/2026 23:14, Tanmay Kathpalia wrote:
> The Altera Agilex5 SoC integrates a Cadence SD6HC controller that needs
> platform-specific configuration to operate correctly.
>
> The SoC requires three named resets: "sdhc-reset" and "sdmmc-ocp" are
> exclusive and must be asserted together before being released, so both
> clock domains cross the reset boundary simultaneously. "combophy" is
> shared with NAND and must only be deasserted, not toggled.
>
> The IOMMU maps DMA addresses within a 40-bit physical address space, so
> the DMA mask is capped at 40 bits to prevent allocation beyond the
> controller's reach.
>
> The silicon requires the MULTIBLOCK_READ_ACMD12, CAP_CLOCK_BASE_BROKEN,
> PRESET_VALUE_BROKEN, and ACMD23_BROKEN quirks. Since
> CAP_CLOCK_BASE_BROKEN prevents reading the base clock from the
> capabilities register, the maximum clock is supplied from the platform
> clock instead.
>
> Signed-off-by: Tanmay Kathpalia <tanmay.kathpalia@altera.com>
> ---
> drivers/mmc/host/sdhci-cadence-core.c | 112 ++++++++++++++++++++++++++
> 1 file changed, 112 insertions(+)
>
> diff --git a/drivers/mmc/host/sdhci-cadence-core.c b/drivers/mmc/host/sdhci-cadence-core.c
> index 5b8a83c9a0aa..0f9b9dd2d2c4 100644
> --- a/drivers/mmc/host/sdhci-cadence-core.c
> +++ b/drivers/mmc/host/sdhci-cadence-core.c
> @@ -7,6 +7,7 @@
>
> #include <linux/bitfield.h>
> #include <linux/bits.h>
> +#include <linux/dma-mapping.h>
> #include <linux/module.h>
>
> #include "sdhci-cadence.h"
> @@ -84,6 +85,7 @@ struct sdhci_cdns4_phy_cfg {
> struct sdhci_cdns_drv_data {
> int (*init)(struct platform_device *pdev);
> const struct sdhci_pltfm_data pltfm_data;
> + u64 dma_mask;
> };
>
> static const struct sdhci_cdns4_phy_cfg sdhci_cdns4_phy_cfgs[] = {
> @@ -193,6 +195,29 @@ static unsigned int sdhci_cdns_get_timeout_clock(struct sdhci_host *host)
> return host->max_clk;
> }
>
> +/**
> + * sdhci_cdns_set_dma_mask - Set platform-specific DMA mask
> + * @host: SDHCI host controller
> + *
> + * Limit DMA addresses to the physical range the controller can reach.
> + */
> +static int sdhci_cdns_set_dma_mask(struct sdhci_host *host)
> +{
> + const struct sdhci_cdns_drv_data *data;
> + struct device *dev = mmc_dev(host->mmc);
> + int ret;
> +
> + data = of_device_get_match_data(dev);
> + if (!data || !data->dma_mask)
> + return 0;
> +
> + ret = dma_set_mask_and_coherent(dev, data->dma_mask);
> + if (ret)
> + return dev_err_probe(dev, ret, "failed to set DMA mask\n");
> +
> + return 0;
> +}
> +
> static void sdhci_cdns_set_emmc_mode(struct sdhci_cdns_priv *priv, u32 mode)
> {
> u32 tmp;
> @@ -460,6 +485,65 @@ static int elba_drv_init(struct platform_device *pdev)
> return 0;
> }
>
> +static int sdhci_cdns6_agilex5_init(struct platform_device *pdev)
> +{
> + struct device *dev = &pdev->dev;
> + struct reset_control *rst_sdhc;
> + struct reset_control *rst_ocp;
> + struct reset_control *rst_combophy;
> + int ret;
> +
> + /*
> + * The combo PHY reset is shared with other peripheral (NAND).
> + * Use the _deasserted variant so devres calls assert + put on driver
> + * detach, keeping the shared deassert reference count balanced across
> + * probe/unbind cycles.
> + */
> + rst_combophy = devm_reset_control_get_shared_deasserted(dev, "combophy");
> + if (IS_ERR(rst_combophy))
> + return dev_err_probe(dev, PTR_ERR(rst_combophy),
> + "failed to get combophy reset\n");
Please don't wrap lines that fit in 100 columns. Same for two below.
> +
> + /*
> + * Assert SDHCI core and SDMMC OCP/AXI bus resets together so their
> + * active periods overlap before both clock domains are released.
> + */
> + rst_sdhc = devm_reset_control_get_exclusive(dev, "sdhc-reset");
> + if (IS_ERR(rst_sdhc))
> + return dev_err_probe(dev, PTR_ERR(rst_sdhc),
> + "failed to get sdhc-reset\n");
> +
> + rst_ocp = devm_reset_control_get_exclusive(dev, "sdmmc-ocp");
> + if (IS_ERR(rst_ocp))
> + return dev_err_probe(dev, PTR_ERR(rst_ocp),
> + "failed to get sdmmc-ocp reset\n");
> +
> + ret = reset_control_assert(rst_sdhc);
> + if (ret)
> + return dev_err_probe(dev, ret, "failed to assert sdhc-reset\n");
> +
> + ret = reset_control_assert(rst_ocp);
> + if (ret) {
> + reset_control_deassert(rst_sdhc);
> + return dev_err_probe(dev, ret, "failed to assert sdmmc-ocp reset\n");
> + }
> +
> + /* Hold resets asserted long enough for all clock domains to capture. */
> + usleep_range(10, 20);
> +
> + ret = reset_control_deassert(rst_sdhc);
> + if (ret) {
> + reset_control_deassert(rst_ocp);
> + return dev_err_probe(dev, ret, "failed to deassert sdhc-reset\n");
> + }
> +
> + ret = reset_control_deassert(rst_ocp);
> + if (ret)
> + return dev_err_probe(dev, ret, "failed to deassert sdmmc-ocp reset\n");
> +
> + return 0;
> +}
> +
> static const struct sdhci_ops sdhci_cdns4_ops = {
> .set_clock = sdhci_set_clock,
> .get_timeout_clock = sdhci_cdns_get_timeout_clock,
> @@ -479,6 +563,18 @@ static const struct sdhci_ops sdhci_cdns6_ops = {
> .hw_reset = sdhci_cdns6_hw_reset,
> };
>
> +static const struct sdhci_ops sdhci_cdns6_agilex5_ops = {
> + .set_clock = sdhci_set_clock,
> + .get_max_clock = sdhci_pltfm_clk_get_max_clock,
> + .get_timeout_clock = sdhci_cdns_get_timeout_clock,
> + .set_bus_width = sdhci_set_bus_width,
> + .reset = sdhci_reset,
> + .platform_execute_tuning = sdhci_cdns_execute_tuning,
> + .set_uhs_signaling = sdhci_cdns_set_uhs_signaling,
> + .hw_reset = sdhci_cdns6_hw_reset,
> + .set_dma_mask = sdhci_cdns_set_dma_mask,
> +};
> +
> static const struct sdhci_cdns_drv_data sdhci_cdns_uniphier_drv_data = {
> .pltfm_data = {
> .ops = &sdhci_cdns4_ops,
> @@ -506,6 +602,18 @@ static const struct sdhci_cdns_drv_data sdhci_cdns4_drv_data = {
> },
> };
>
> +static const struct sdhci_cdns_drv_data sdhci_cdns6_agilex5_drv_data = {
> + .init = sdhci_cdns6_agilex5_init,
> + .pltfm_data = {
> + .ops = &sdhci_cdns6_agilex5_ops,
> + .quirks = SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN |
> + SDHCI_QUIRK_MULTIBLOCK_READ_ACMD12,
> + .quirks2 = SDHCI_QUIRK2_PRESET_VALUE_BROKEN |
> + SDHCI_QUIRK2_ACMD23_BROKEN,
> + },
> + .dma_mask = DMA_BIT_MASK(40),
> +};
> +
> static const struct sdhci_cdns_drv_data sdhci_cdns6_drv_data = {
> .pltfm_data = {
> .ops = &sdhci_cdns6_ops,
> @@ -704,6 +812,10 @@ static const struct of_device_id sdhci_cdns_match[] = {
> .compatible = "cdns,sd4hc",
> .data = &sdhci_cdns4_drv_data,
> },
> + {
> + .compatible = "altr,agilex5-sd6hc",
> + .data = &sdhci_cdns6_agilex5_drv_data,
> + },
> {
> .compatible = "cdns,sd6hc",
> .data = &sdhci_cdns6_drv_data,
prev parent reply other threads:[~2026-07-04 11:18 UTC|newest]
Thread overview: 28+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-06-27 20:14 [PATCH v2 0/9] mmc: sdhci-cadence: add SD6HC support and Agilex5 enablement Tanmay Kathpalia
2026-06-27 20:14 ` [PATCH v2 1/9] dt-bindings: reset: altr: add COMBOPHY_RESET for Agilex5 Tanmay Kathpalia
2026-07-02 15:53 ` (subset) " Philipp Zabel
2026-06-27 20:14 ` [PATCH v2 2/9] dt-bindings: mmc: cdns,sdhci: add SD6HC support and PHY properties Tanmay Kathpalia
2026-06-27 20:26 ` sashiko-bot
2026-06-28 9:46 ` Kathpalia, Tanmay
2026-06-29 7:04 ` Krzysztof Kozlowski
2026-07-02 8:58 ` Kathpalia, Tanmay
2026-06-27 20:14 ` [PATCH v2 3/9] arm64: dts: agilex5: add Cadence SD6HC controller and SOCDK enablement Tanmay Kathpalia
2026-06-27 20:24 ` sashiko-bot
2026-06-28 9:55 ` Kathpalia, Tanmay
2026-06-29 7:06 ` Krzysztof Kozlowski
2026-07-02 9:01 ` Kathpalia, Tanmay
2026-06-27 20:14 ` [PATCH v2 4/9] dt-bindings: arm: intel: add Agilex5 SOCDK eMMC board variant Tanmay Kathpalia
2026-06-29 7:06 ` Krzysztof Kozlowski
2026-07-02 9:07 ` Kathpalia, Tanmay
2026-06-27 20:14 ` [PATCH v2 5/9] arm64: dts: agilex5: add SOCDK eMMC daughter board support Tanmay Kathpalia
2026-06-29 7:07 ` Krzysztof Kozlowski
2026-07-02 9:07 ` Kathpalia, Tanmay
2026-06-27 20:14 ` [PATCH v2 6/9] mmc: sdhci-cadence: rename V4 functions for V6 controller groundwork Tanmay Kathpalia
2026-07-04 11:17 ` Adrian Hunter
2026-06-27 20:14 ` [PATCH v2 7/9] mmc: sdhci-cadence: refactor driver structure for V6 controller support Tanmay Kathpalia
2026-06-27 20:14 ` [PATCH v2 8/9] mmc: sdhci-cadence: add Cadence SD6HC support Tanmay Kathpalia
2026-07-04 11:18 ` Adrian Hunter
2026-06-27 20:14 ` [PATCH v2 9/9] mmc: sdhci-cadence: add Altera Agilex5 " Tanmay Kathpalia
2026-06-29 7:08 ` Krzysztof Kozlowski
2026-07-02 9:04 ` Kathpalia, Tanmay
2026-07-04 11:18 ` Adrian Hunter [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1c57e707-dd72-499a-88c9-8129da28bf74@intel.com \
--to=adrian.hunter@intel.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mmc@vger.kernel.org \
--cc=p.zabel@pengutronix.de \
--cc=tanmay.kathpalia@altera.com \
--cc=ulf.hansson@linaro.org \
--cc=ulfh@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.