* Adding a second card (hvr-1110), video from old card (bt878) stutters
@ 2008-02-03 7:23 Fredrik Staxeng
0 siblings, 0 replies; only message in thread
From: Fredrik Staxeng @ 2008-02-03 7:23 UTC (permalink / raw)
To: video4linux-list
I have a working mythtv box with an old Hauappauge card in it. I tried to add
another card, a HVR-1110, the version with an saa7133 on it.
I added some udev rules to keep the old card on video0. Then I put the card
in the box and rebooted. First I checked whether mythtv was still working.
I got picure, but it was stuttery, about 10 frames per second or so, and
there was no sound.
I did not try to use the new card, not configuring it and not even
connecting the antenna. There was a message about missing firmware for
that when booting. Gdm did not log automatically.
I removed the new card, and rebooted. Fortunately everything worked, even
the gdm login.
Why would the mere presence of the new card in the system interfere with
the old one?
I use mythtv on ubuntu 7.10. The bttv driver is version 0.9.17,
the saa7130 is 0.2.14, mythtv is 0.20.2.
The motherboard is an ASUS M2NPV-VM, the kernel says the old card is a
Hauppauge WinTV [card=10], PCI subsystem ID is 0070:13eb.
The udev lines I used are these
KERNEL=="video[0-9]*", DRIVERS=="bttv" , NAME="video0", SYMLINK += "video-bttv"
KERNEL=="vbi[0-9]*", DRIVERS=="bttv" , NAME="vbi0", SYMLINK += "vbi-bttv"
KERNEL=="radio[0-9]*", DRIVERS=="bttv" , NAME="radio0", SYMLINK += "radio-bttv"
KERNEL=="video[0-9]*", DRIVERS!="bttv" , NAME="v4l/video%n"
KERNEL=="vbi[0-9]*", DRIVERS!="bttv" , NAME="v4l/vbi%n"
KERNEL=="radio[0-9]*", DRIVERS!="bttv" , NAME="v4l/radio%n"
This is the dmesg output:
[ 0.000000] Linux version 2.6.22-14-generic (buildd@terranova) (gcc version 4.1.3 20070929 (prerelease) (Ubuntu 4.1.2-16ubuntu2)) #1 SMP Tue Dec 18 08:02:57 UTC 2007 (Ubuntu 2.6.22-14.47-generic)
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f000 (usable)
[ 0.000000] BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000003dee0000 (usable)
[ 0.000000] BIOS-e820: 000000003dee0000 - 000000003dee3000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000003dee3000 - 000000003def0000 (ACPI data)
[ 0.000000] BIOS-e820: 000000003def0000 - 000000003df00000 (reserved)
[ 0.000000] BIOS-e820: 000000003e000000 - 0000000040000000 (reserved)
[ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
[ 0.000000] 94MB HIGHMEM available.
[ 0.000000] 896MB LOWMEM available.
[ 0.000000] found SMP MP-table at 000f59c0
[ 0.000000] Entering add_active_range(0, 0, 253664) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 229376
[ 0.000000] HighMem 229376 -> 253664
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 253664
[ 0.000000] On node 0 totalpages: 253664
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 1760 pages used for memmap
[ 0.000000] Normal zone: 223520 pages, LIFO batch:31
[ 0.000000] HighMem zone: 189 pages used for memmap
[ 0.000000] HighMem zone: 24099 pages, LIFO batch:3
[ 0.000000] DMI 2.4 present.
[ 0.000000] ACPI: RSDP signature @ 0xC00F74B0 checksum 0
[ 0.000000] ACPI: RSDP 000F74B0, 0024 (r2 Nvidia)
[ 0.000000] ACPI: XSDT 3DEE30C0, 004C (r1 Nvidia ASUSACPI 42302E31 AWRD 0)
[ 0.000000] ACPI: FACP 3DEEB4C0, 00F4 (r3 Nvidia ASUSACPI 42302E31 AWRD 0)
[ 0.000000] ACPI: DSDT 3DEE3240, 821E (r1 NVIDIA ASUSACPI 1000 MSFT 3000000)
[ 0.000000] ACPI: FACS 3DEE0000, 0040
[ 0.000000] ACPI: SSDT 3DEEB6C0, 0248 (r1 PTLTD POWERNOW 1 LTP 1)
[ 0.000000] ACPI: HPET 3DEEB980, 0038 (r1 Nvidia ASUSACPI 42302E31 AWRD 98)
[ 0.000000] ACPI: MCFG 3DEEBA00, 003C (r1 Nvidia ASUSACPI 42302E31 AWRD 0)
[ 0.000000] ACPI: APIC 3DEEB600, 007C (r1 Nvidia ASUSACPI 42302E31 AWRD 0)
[ 0.000000] ACPI: PM-Timer IO Port: 0x4008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] Processor #0 15:11 APIC version 16
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[ 0.000000] Processor #1 15:11 APIC version 16
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] ACPI: IRQ14 used by override.
[ 0.000000] ACPI: IRQ15 used by override.
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] ACPI: HPET id: 0x10de8201 base: 0xfefff000
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] Allocating PCI resources starting at 50000000 (gap: 40000000:a0000000)
[ 0.000000] Built 1 zonelists. Total pages: 251683
[ 0.000000] Kernel command line: root=UUID=98eb5c1c-ff35-4492-a3d8-8e1839a89c03 ro quiet splash
[ 0.000000] mapped APIC to ffffd000 (fee00000)
[ 0.000000] mapped IOAPIC to ffffc000 (fec00000)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[ 0.000000] Detected 2304.840 MHz processor.
[ 0.000000] spurious 8259A interrupt: IRQ7.
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Memory: 994256k/1014656k available (2015k kernel code, 19764k reserved, 916k data, 364k init, 97152k highmem)
[ 0.000000] virtual kernel memory layout:
[ 0.000000] fixmap : 0xfff4d000 - 0xfffff000 ( 712 kB)
[ 0.000000] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 0.000000] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
[ 0.000000] .init : 0xc03e3000 - 0xc043e000 ( 364 kB)
[ 0.000000] .data : 0xc02f7de6 - 0xc03dce84 ( 916 kB)
[ 0.000000] .text : 0xc0100000 - 0xc02f7de6 (2015 kB)
[ 0.000000] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[ 0.000000] SLUB: Genslabs=22, HWalign=64, Order=0-1, MinObjects=4, CPUs=2, Nodes=1
[ 0.000000] hpet0: at MMIO 0xfefff000, IRQs 2, 8, 31
[ 0.000000] hpet0: 3 32-bit timers, 25000000 Hz
[ 0.080000] Calibrating delay using timer specific routine.. 4613.39 BogoMIPS (lpj=9226789)
[ 0.080000] Security Framework v1.0.0 initialized
[ 0.080000] SELinux: Disabled at boot.
[ 0.080000] Mount-cache hash table entries: 512
[ 0.080000] CPU: After generic identify, caps: 178bfbff ebd3fbff 00000000 00000000 00002001 00000000 0000011f
[ 0.080000] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 0.080000] CPU: L2 Cache: 512K (64 bytes/line)
[ 0.080000] CPU 0(2) -> Core 0
[ 0.080000] CPU: After all inits, caps: 178bfbff ebd3fbff 00000000 00000410 00002001 00000000 0000011f
[ 0.080000] Compat vDSO mapped to ffffe000.
[ 0.080000] Checking 'hlt' instruction... OK.
[ 0.096000] SMP alternatives: switching to UP code
[ 0.096000] Early unpacking initramfs... done
[ 0.348000] ACPI: Core revision 20070126
[ 0.348000] ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found.
[ 0.352000] CPU0: AMD Athlon(tm) 64 X2 Dual Core Processor 4400+ stepping 01
[ 0.352000] SMP alternatives: switching to SMP code
[ 0.352000] Booting processor 1/1 eip 3000
[ 0.360000] Initializing CPU#1
[ 0.444000] Calibrating delay using timer specific routine.. 4609.65 BogoMIPS (lpj=9219306)
[ 0.444000] CPU: After generic identify, caps: 178bfbff ebd3fbff 00000000 00000000 00002001 00000000 0000011f
[ 0.444000] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 0.444000] CPU: L2 Cache: 512K (64 bytes/line)
[ 0.444000] CPU 1(2) -> Core 1
[ 0.444000] CPU: After all inits, caps: 178bfbff ebd3fbff 00000000 00000410 00002001 00000000 0000011f
[ 0.444000] CPU1: AMD Athlon(tm) 64 X2 Dual Core Processor 4400+ stepping 01
[ 0.444000] Total of 2 processors activated (9223.04 BogoMIPS).
[ 0.444000] ENABLING IO-APIC IRQs
[ 0.444000] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.488000] Brought up 2 CPUs
[ 0.500000] migration_cost=4000
[ 0.500000] Booting paravirtualized kernel on bare hardware
[ 0.500000] Time: 16:22:43 Date: 01/02/108
[ 0.500000] NET: Registered protocol family 16
[ 0.500000] EISA bus registered
[ 0.500000] ACPI: bus type pci registered
[ 0.508000] PCI: PCI BIOS revision 3.00 entry at 0xf1ff0, last bus=4
[ 0.508000] PCI: Using configuration type 1
[ 0.508000] Setting up standard PCI resources
[ 0.512000] ACPI: EC: Look up EC in DSDT
[ 0.520000] ACPI: Interpreter enabled
[ 0.520000] ACPI: (supports S0 S1 S3 S4 S5)
[ 0.520000] ACPI: Using IOAPIC for interrupt routing
[ 0.528000] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.528000] PCI: Probing PCI hardware (bus 00)
[ 0.532000] PCI: Transparent bridge - 0000:00:10.0
[ 0.532000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.532000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
[ 0.600000] ACPI: PCI Interrupt Link [LNK1] (IRQs 5 7 9 10 *11 14 15)
[ 0.600000] ACPI: PCI Interrupt Link [LNK2] (IRQs *5 7 9 10 11 14 15)
[ 0.600000] ACPI: PCI Interrupt Link [LNK3] (IRQs 5 7 9 10 11 14 15) *0, disabled.
[ 0.600000] ACPI: PCI Interrupt Link [LNK4] (IRQs 5 7 9 *10 11 14 15)
[ 0.600000] ACPI: PCI Interrupt Link [LNK5] (IRQs 5 7 9 10 11 14 15) *0, disabled.
[ 0.600000] ACPI: PCI Interrupt Link [LNK6] (IRQs 5 7 9 10 11 14 15) *0, disabled.
[ 0.600000] ACPI: PCI Interrupt Link [LNK7] (IRQs *5 7 9 10 11 14 15)
[ 0.600000] ACPI: PCI Interrupt Link [LNK8] (IRQs 5 7 9 10 11 14 15) *0, disabled.
[ 0.600000] ACPI: PCI Interrupt Link [LUBA] (IRQs *5 7 9 10 11 14 15)
[ 0.600000] ACPI: PCI Interrupt Link [LUBB] (IRQs 5 7 9 10 11 14 15) *0, disabled.
[ 0.600000] ACPI: PCI Interrupt Link [LMAC] (IRQs 5 7 9 10 *11 14 15)
[ 0.600000] ACPI: PCI Interrupt Link [LACI] (IRQs 5 7 9 10 11 14 15) *0, disabled.
[ 0.600000] ACPI: PCI Interrupt Link [LAZA] (IRQs 5 7 9 *10 11 14 15)
[ 0.600000] ACPI: PCI Interrupt Link [LPMU] (IRQs 5 7 9 10 11 14 15) *0, disabled.
[ 0.600000] ACPI: PCI Interrupt Link [LMCI] (IRQs 5 7 9 10 11 14 15) *0, disabled.
[ 0.600000] ACPI: PCI Interrupt Link [LSMB] (IRQs 5 7 9 *10 11 14 15)
[ 0.600000] ACPI: PCI Interrupt Link [LUB2] (IRQs *5 7 9 10 11 14 15)
[ 0.600000] ACPI: PCI Interrupt Link [LIDE] (IRQs 5 7 9 10 11 14 15) *0, disabled.
[ 0.604000] ACPI: PCI Interrupt Link [LSID] (IRQs *5 7 9 10 11 14 15)
[ 0.604000] ACPI: PCI Interrupt Link [LFID] (IRQs *5 7 9 10 11 14 15)
[ 0.604000] ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0
[ 0.604000] ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0
[ 0.604000] ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0, disabled.
[ 0.604000] ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0
[ 0.604000] ACPI: PCI Interrupt Link [APC5] (IRQs 16) *0, disabled.
[ 0.604000] ACPI: PCI Interrupt Link [APC6] (IRQs 16) *0, disabled.
[ 0.604000] ACPI: PCI Interrupt Link [APC7] (IRQs 16) *0
[ 0.604000] ACPI: PCI Interrupt Link [APC8] (IRQs 16) *0, disabled.
[ 0.604000] ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22 23) *0
[ 0.604000] ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22 23) *0, disabled.
[ 0.604000] ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0
[ 0.604000] ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22 23) *0, disabled.
[ 0.604000] ACPI: PCI Interrupt Link [APMU] (IRQs 20 21 22 23) *0, disabled.
[ 0.604000] ACPI: PCI Interrupt Link [AAZA] (IRQs 20 21 22 23) *0
[ 0.604000] ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22 23) *0, disabled.
[ 0.604000] ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0
[ 0.604000] ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22 23) *0
[ 0.604000] ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22 23) *0, disabled.
[ 0.608000] ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled.
[ 0.608000] ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0
[ 0.608000] ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22 23) *0
[ 0.608000] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 0.608000] pnp: PnP ACPI init
[ 0.608000] ACPI: bus type pnp registered
[ 0.612000] pnp: PnP ACPI: found 15 devices
[ 0.612000] ACPI: ACPI bus type pnp unregistered
[ 0.612000] PnPBIOS: Disabled by ACPI PNP
[ 0.612000] PCI: Using ACPI for IRQ routing
[ 0.612000] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[ 0.708000] NET: Registered protocol family 8
[ 0.708000] NET: Registered protocol family 20
[ 0.708000] pnp: 00:01: ioport range 0x4000-0x407f has been reserved
[ 0.708000] pnp: 00:01: ioport range 0x4080-0x40ff has been reserved
[ 0.708000] pnp: 00:01: ioport range 0x4400-0x447f has been reserved
[ 0.708000] pnp: 00:01: ioport range 0x4480-0x44ff has been reserved
[ 0.708000] pnp: 00:01: ioport range 0x4800-0x487f has been reserved
[ 0.708000] pnp: 00:01: ioport range 0x4880-0x48ff has been reserved
[ 0.708000] pnp: 00:01: ioport range 0x2000-0x207f has been reserved
[ 0.708000] pnp: 00:01: ioport range 0x2080-0x20ff has been reserved
[ 0.708000] pnp: 00:01: iomem range 0x3e000000-0x3fffffff could not be reserved
[ 0.708000] pnp: 00:0d: iomem range 0xe0000000-0xefffffff could not be reserved
[ 0.708000] pnp: 00:0e: iomem range 0xcec00-0xcffff has been reserved
[ 0.708000] pnp: 00:0e: iomem range 0xf0000-0xf7fff could not be reserved
[ 0.708000] pnp: 00:0e: iomem range 0xf8000-0xfbfff could not be reserved
[ 0.708000] pnp: 00:0e: iomem range 0xfc000-0xfffff could not be reserved
[ 0.712000] Time: hpet clocksource has been installed.
[ 0.712000] Switched to high resolution mode on CPU 0
[ 0.712000] Switched to high resolution mode on CPU 1
[ 0.740000] PCI: Bridge: 0000:00:02.0
[ 0.740000] IO window: a000-afff
[ 0.740000] MEM window: fd800000-fd8fffff
[ 0.740000] PREFETCH window: fd700000-fd7fffff
[ 0.740000] PCI: Bridge: 0000:00:03.0
[ 0.740000] IO window: 8000-8fff
[ 0.740000] MEM window: fde00000-fdefffff
[ 0.740000] PREFETCH window: fdd00000-fddfffff
[ 0.740000] PCI: Bridge: 0000:00:04.0
[ 0.740000] IO window: b000-bfff
[ 0.740000] MEM window: fdc00000-fdcfffff
[ 0.740000] PREFETCH window: fd900000-fd9fffff
[ 0.740000] PCI: Bridge: 0000:00:10.0
[ 0.740000] IO window: 9000-9fff
[ 0.740000] MEM window: fdb00000-fdbfffff
[ 0.740000] PREFETCH window: fda00000-fdafffff
[ 0.740000] PCI: Setting latency timer of device 0000:00:02.0 to 64
[ 0.740000] PCI: Setting latency timer of device 0000:00:03.0 to 64
[ 0.740000] PCI: Setting latency timer of device 0000:00:04.0 to 64
[ 0.740000] PCI: Setting latency timer of device 0000:00:10.0 to 64
[ 0.740000] NET: Registered protocol family 2
[ 0.784000] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.784000] TCP established hash table entries: 131072 (order: 8, 1572864 bytes)
[ 0.784000] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.784000] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.784000] TCP reno registered
[ 0.800000] checking if image is initramfs... it is
[ 1.296000] Freeing initrd memory: 7114k freed
[ 1.296000] audit: initializing netlink socket (disabled)
[ 1.296000] audit(1201969363.212:1): initialized
[ 1.296000] highmem bounce pool size: 64 pages
[ 1.296000] VFS: Disk quotas dquot_6.5.1
[ 1.296000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.296000] io scheduler noop registered
[ 1.296000] io scheduler anticipatory registered
[ 1.296000] io scheduler deadline registered
[ 1.296000] io scheduler cfq registered (default)
[ 1.296000] Boot video device is 0000:00:05.0
[ 1.312000] PCI: Setting latency timer of device 0000:00:02.0 to 64
[ 1.312000] assign_interrupt_mode Found MSI capability
[ 1.312000] Allocate Port Service[0000:00:02.0:pcie00]
[ 1.312000] PCI: Setting latency timer of device 0000:00:03.0 to 64
[ 1.312000] assign_interrupt_mode Found MSI capability
[ 1.312000] Allocate Port Service[0000:00:03.0:pcie00]
[ 1.312000] PCI: Setting latency timer of device 0000:00:04.0 to 64
[ 1.312000] assign_interrupt_mode Found MSI capability
[ 1.312000] Allocate Port Service[0000:00:04.0:pcie00]
[ 1.312000] isapnp: Scanning for PnP cards...
[ 1.664000] isapnp: No Plug & Play device found
[ 1.680000] Real Time Clock Driver v1.12ac
[ 1.680000] hpet_resources: 0xfefff000 is busy
[ 1.680000] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 1.680000] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.684000] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 1.684000] 00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.684000] 00:0a: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 1.684000] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[ 1.684000] input: Macintosh mouse button emulation as /class/input/input0
[ 1.684000] PNP: No PS/2 controller found. Probing ports directly.
[ 1.684000] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.684000] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 1.684000] mice: PS/2 mouse device common for all mice
[ 1.684000] EISA: Probing bus 0 at eisa.0
[ 1.684000] Cannot allocate resource for EISA slot 2
[ 1.684000] Cannot allocate resource for EISA slot 4
[ 1.684000] Cannot allocate resource for EISA slot 8
[ 1.684000] EISA: Detected 0 cards.
[ 1.684000] TCP cubic registered
[ 1.684000] NET: Registered protocol family 1
[ 1.684000] Using IPI No-Shortcut mode
[ 1.684000] Magic number: 12:642:387
[ 1.684000] Freeing unused kernel memory: 364k freed
[ 2.880000] AppArmor: AppArmor initialized<5>audit(1201969364.712:2): type=1505 info="AppArmor initialized" pid=1286
[ 2.884000] fuse init (API version 7.8)
[ 2.892000] Failure registering capabilities with primary security module.
[ 2.920000] ACPI: Fan [FAN] (on)
[ 2.928000] ACPI: Thermal Zone [THRM] (40 C)
[ 3.464000] SCSI subsystem initialized
[ 3.468000] libata version 2.21 loaded.
[ 3.480000] sata_nv 0000:00:0e.0: version 3.4
[ 3.480000] ACPI: PCI Interrupt Link [APSI] enabled at IRQ 23
[ 3.480000] ACPI: PCI Interrupt 0000:00:0e.0[A] -> Link [APSI] -> GSI 23 (level, low) -> IRQ 16
[ 3.480000] PCI: Setting latency timer of device 0000:00:0e.0 to 64
[ 3.480000] scsi0 : sata_nv
[ 3.480000] scsi1 : sata_nv
[ 3.480000] ata1: SATA max UDMA/133 cmd 0x000109f0 ctl 0x00010bf2 bmdma 0x0001e000 irq 16
[ 3.480000] ata2: SATA max UDMA/133 cmd 0x00010970 ctl 0x00010b72 bmdma 0x0001e008 irq 16
[ 3.516000] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 3.516000] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 3.532000] usbcore: registered new interface driver usbfs
[ 3.532000] usbcore: registered new interface driver hub
[ 3.556000] usbcore: registered new device driver usb
[ 3.556000] forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.60.
[ 3.568000] Floppy drive(s): fd0 is 1.44M
[ 3.608000] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
[ 3.608000] FDC 0 is a post-1991 82077
[ 3.792000] ata1: SATA link down (SStatus 0 SControl 300)
[ 4.112000] ata2: SATA link down (SStatus 0 SControl 300)
[ 4.120000] ACPI: PCI Interrupt Link [APSJ] enabled at IRQ 22
[ 4.120000] ACPI: PCI Interrupt 0000:00:0f.0[A] -> Link [APSJ] -> GSI 22 (level, low) -> IRQ 17
[ 4.120000] PCI: Setting latency timer of device 0000:00:0f.0 to 64
[ 4.120000] scsi2 : sata_nv
[ 4.120000] scsi3 : sata_nv
[ 4.120000] ata3: SATA max UDMA/133 cmd 0x000109e0 ctl 0x00010be2 bmdma 0x0001cc00 irq 17
[ 4.120000] ata4: SATA max UDMA/133 cmd 0x00010960 ctl 0x00010b62 bmdma 0x0001cc08 irq 17
[ 4.432000] ata3: SATA link down (SStatus 0 SControl 300)
[ 4.752000] ata4: SATA link down (SStatus 0 SControl 300)
[ 4.760000] NFORCE-MCP51: IDE controller at PCI slot 0000:00:0d.0
[ 4.760000] NFORCE-MCP51: chipset revision 161
[ 4.760000] NFORCE-MCP51: not 100% native mode: will probe irqs later
[ 4.760000] NFORCE-MCP51: 0000:00:0d.0 (rev a1) UDMA133 controller
[ 4.760000] ide0: BM-DMA at 0xf400-0xf407, BIOS settings: hda:DMA, hdb:DMA
[ 4.760000] ide1: BM-DMA at 0xf408-0xf40f, BIOS settings: hdc:DMA, hdd:DMA
[ 4.760000] Probing IDE interface ide0...
[ 5.048000] hda: SAMSUNG SP2514N, ATA DISK drive
[ 5.748000] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 5.752000] Probing IDE interface ide1...
[ 6.492000] hdc: ASUS DVD-ROM E608, ATAPI CD/DVD-ROM drive
[ 6.828000] ide1 at 0x170-0x177,0x376 on irq 15
[ 6.828000] ACPI: PCI Interrupt Link [APCH] enabled at IRQ 21
[ 6.828000] ACPI: PCI Interrupt 0000:00:14.0[A] -> Link [APCH] -> GSI 21 (level, low) -> IRQ 18
[ 6.828000] PCI: Setting latency timer of device 0000:00:14.0 to 64
[ 6.828000] forcedeth: using HIGHDMA
[ 7.348000] eth0: forcedeth.c: subsystem: 01043:816a bound to 0000:00:14.0
[ 7.348000] ACPI: PCI Interrupt Link [APCF] enabled at IRQ 20
[ 7.348000] ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [APCF] -> GSI 20 (level, low) -> IRQ 19
[ 7.348000] PCI: Setting latency timer of device 0000:00:0b.0 to 64
[ 7.348000] ohci_hcd 0000:00:0b.0: OHCI Host Controller
[ 7.348000] ohci_hcd 0000:00:0b.0: new USB bus registered, assigned bus number 1
[ 7.348000] ohci_hcd 0000:00:0b.0: irq 19, io mem 0xfe02f000
[ 7.404000] usb usb1: configuration #1 chosen from 1 choice
[ 7.404000] hub 1-0:1.0: USB hub found
[ 7.404000] hub 1-0:1.0: 8 ports detected
[ 7.508000] ACPI: PCI Interrupt Link [APCL] enabled at IRQ 23
[ 7.508000] ACPI: PCI Interrupt 0000:00:0b.1[B] -> Link [APCL] -> GSI 23 (level, low) -> IRQ 16
[ 7.508000] PCI: Setting latency timer of device 0000:00:0b.1 to 64
[ 7.508000] ehci_hcd 0000:00:0b.1: EHCI Host Controller
[ 7.508000] ehci_hcd 0000:00:0b.1: new USB bus registered, assigned bus number 2
[ 7.508000] ehci_hcd 0000:00:0b.1: debug port 1
[ 7.508000] PCI: cache line size of 64 is not supported by device 0000:00:0b.1
[ 7.508000] ehci_hcd 0000:00:0b.1: irq 16, io mem 0xfe02e000
[ 7.508000] ehci_hcd 0000:00:0b.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 7.508000] usb usb2: configuration #1 chosen from 1 choice
[ 7.508000] hub 2-0:1.0: USB hub found
[ 7.508000] hub 2-0:1.0: 8 ports detected
[ 7.612000] ACPI: PCI Interrupt Link [APC4] enabled at IRQ 19
[ 7.612000] ACPI: PCI Interrupt 0000:04:05.0[A] -> Link [APC4] -> GSI 19 (level, low) -> IRQ 20
[ 7.660000] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[20] MMIO=[fdbff000-fdbff7ff] Max Packet=[2048] IR/IT contexts=[4/8]
[ 7.664000] hda: max request size: 512KiB
[ 7.664000] hda: 488397168 sectors (250059 MB) w/8192KiB Cache, CHS=30401/255/63, UDMA(100)
[ 7.664000] hda: cache flushes supported
[ 7.664000] hda:<6>hdc: ATAPI 40X DVD-ROM drive, 128kB Cache, UDMA(33)
[ 7.664000] Uniform CD-ROM driver Revision: 3.20
[ 7.672000] hda1 hda2 hda3
[ 7.896000] Attempting manual resume
[ 7.896000] swsusp: Resume From Partition 3:2
[ 7.896000] PM: Checking swsusp image.
[ 7.900000] PM: Resume from disk failed.
[ 7.928000] kjournald starting. Commit interval 5 seconds
[ 7.928000] EXT3-fs: mounted filesystem with ordered data mode.
[ 8.552000] usb 1-1: new full speed USB device using ohci_hcd and address 2
[ 8.752000] usb 1-1: configuration #1 chosen from 1 choice
[ 8.932000] ieee1394: Host added: ID:BUS[0-00:1023] GUID[0011d8000123f756]
[ 9.060000] usb 1-2: new low speed USB device using ohci_hcd and address 3
[ 9.276000] usb 1-2: configuration #1 chosen from 1 choice
[ 14.156000] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 14.200000] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 14.300000] i2c-adapter i2c-0: nForce2 SMBus adapter at 0x4c00
[ 14.300000] i2c-adapter i2c-1: nForce2 SMBus adapter at 0x4c40
[ 14.484000] Linux video capture interface: v2.00
[ 14.528000] Linux agpgart interface v0.102 (c) Dave Jones
[ 14.644000] saa7130/34: v4l2 driver version 0.2.14 loaded
[ 14.644000] ACPI: PCI Interrupt Link [APC2] enabled at IRQ 17
[ 14.644000] ACPI: PCI Interrupt 0000:04:09.0[A] -> Link [APC2] -> GSI 17 (level, low) -> IRQ 21
[ 14.644000] saa7133[0]: found at 0000:04:09.0, rev: 209, irq: 21, latency: 32, mmio: 0xfdbfe000
[ 14.644000] saa7133[0]: subsystem: 0070:6701, board: Hauppauge WinTV-HVR1110 DVB-T/Hybrid [card=104,autodetected]
[ 14.644000] saa7133[0]: board init: gpio is 6400000
[ 14.684000] input: PC Speaker as /class/input/input1
[ 14.700000] nvidia: module license 'NVIDIA' taints kernel.
[ 14.956000] bttv: driver version 0.9.17 loaded
[ 14.956000] bttv: using 8 buffers with 2080k (520 pages) each for capture
[ 14.976000] input: HVR 1110 as /class/input/input2
[ 14.976000] ir-kbd-i2c: HVR 1110 detected at i2c-2/2-0071/ir0 [saa7133[0]]
[ 15.012000] usbcore: registered new interface driver hiddev
[ 15.020000] saa7133[0]: i2c eeprom 00: 70 00 01 67 54 20 1c 00 43 43 a9 1c 55 d2 b2 92
[ 15.020000] saa7133[0]: i2c eeprom 10: ff ff ff 0e ff 20 ff ff ff ff ff ff ff ff ff ff
[ 15.020000] saa7133[0]: i2c eeprom 20: 01 40 01 32 32 01 01 33 88 ff 00 aa ff ff ff ff
[ 15.020000] saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 15.020000] saa7133[0]: i2c eeprom 40: ff 21 00 c2 96 10 03 32 15 60 ff ff ff ff ff ff
[ 15.020000] saa7133[0]: i2c eeprom 50: ff 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 15.020000] saa7133[0]: i2c eeprom 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 15.020000] saa7133[0]: i2c eeprom 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 15.020000] input: ruwido austria GmbH ruwido austria GmbH USB Infrared Keyboard V2.07 as /class/input/input3
[ 15.020000] input: USB HID v1.10 Keyboard [ruwido austria GmbH ruwido austria GmbH USB Infrared Keyboard V2.07] on usb-0000:00:0b.0-2
[ 15.024000] lirc_dev: IR Remote Control driver registered, at major 61
[ 15.028000] input: ruwido austria GmbH ruwido austria GmbH USB Infrared Keyboard V2.07 as /class/input/input4
[ 15.028000] input: USB HID v1.10 Mouse [ruwido austria GmbH ruwido austria GmbH USB Infrared Keyboard V2.07] on usb-0000:00:0b.0-2
[ 15.028000] usbcore: registered new interface driver usbhid
[ 15.028000] /build/buildd/linux-source-2.6.22-2.6.22/drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
[ 15.072000]
[ 15.072000] lirc_mceusb2: Philips eHome USB IR Transciever and Microsoft MCE 2005 Remote Control driver for LIRC $Revision: 1.33 $
[ 15.072000] lirc_mceusb2: Daniel Melander <lirc@rajidae.se>, Martin Blatter <martin_a_blatter@yahoo.com>
[ 15.072000] parport_pc 00:0b: reported by Plug and Play ACPI
[ 15.072000] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE,EPP]
[ 15.128000] tuner 2-004b: chip found @ 0x96 (saa7133[0])
[ 15.192000] tuner 2-004b: setting tuner address to 61
[ 15.232000] tuner 2-004b: type set to tda8290+75a
[ 15.256000] usb 1-1: reset full speed USB device using ohci_hcd and address 2
[ 15.460000] lirc_dev: lirc_register_plugin: sample_rate: 0
[ 15.468000] lirc_mceusb2[2]: Philips eHome Infrared Transceiver on usb1:2
[ 15.468000] usbcore: registered new interface driver lirc_mceusb2
[ 16.624000] tuner 2-004b: setting tuner address to 61
[ 16.664000] tuner 2-004b: type set to tda8290+75a
[ 18.008000] saa7133[0]: registered device video0 [v4l2]
[ 18.008000] saa7133[0]: registered device vbi0
[ 18.008000] saa7133[0]: registered device radio0
[ 18.072000] bttv: Bt8xx card found (0).
[ 18.072000] ACPI: PCI Interrupt Link [APC1] enabled at IRQ 16
[ 18.072000] ACPI: PCI Interrupt 0000:04:08.0[A] -> Link [APC1] -> GSI 16 (level, low) -> IRQ 22
[ 18.072000] bttv0: Bt878 (rev 2) at 0000:04:08.0, irq: 22, latency: 32, mmio: 0xfdaff000
[ 18.072000] bttv0: detected: Hauppauge WinTV [card=10], PCI subsystem ID is 0070:13eb
[ 18.072000] bttv0: using: Hauppauge (bt878) [card=10,autodetected]
[ 18.072000] bttv0: gpio: en=00000000, out=00000000 in=00ffffdb [init]
[ 18.072000] bttv0: Hauppauge/Voodoo msp34xx: reset line init [5]
[ 18.076000] input: i2c IR (Hauppauge) as /class/input/input5
[ 18.076000] ir-kbd-i2c: i2c IR (Hauppauge) detected at i2c-3/3-0018/ir0 [bt878 #0 [sw]]
[ 18.076000] i2c-adapter i2c-3: sendbytes: error - bailout.
[ 18.084000] saa7134 ALSA driver for DMA sound loaded
[ 18.084000] saa7133[0]/alsa: saa7133[0] at 0xfdbfe000 irq 21 registered as card -2
[ 18.100000] tuner 3-0042: chip found @ 0x84 (bt878 #0 [sw])
[ 18.100000] tda9887 3-0042: tda988[5/6/7] found @ 0x42 (tuner)
[ 18.108000] tuner 3-0061: chip found @ 0xc2 (bt878 #0 [sw])
[ 18.140000] tveeprom 3-0050: Hauppauge model 61344, rev D121, serial# 3507592
[ 18.140000] tveeprom 3-0050: tuner model is Philips FM1216 (idx 21, type 5)
[ 18.140000] tveeprom 3-0050: TV standards PAL(B/G) (eeprom 0x04)
[ 18.140000] tveeprom 3-0050: audio processor is MSP3415 (idx 6)
[ 18.140000] tveeprom 3-0050: has radio
[ 18.140000] bttv0: Hauppauge eeprom indicates model#61344
[ 18.140000] bttv0: using tuner=5
[ 18.140000] tuner 3-0061: type set to 5 (Philips PAL_BG (FI1216 and compatibles))
[ 18.140000] bttv0: i2c: checking for MSP34xx @ 0x80... found
[ 18.164000] msp3400 3-0040: MSP3410D-B4 found @ 0x80 (bt878 #0 [sw])
[ 18.164000] msp3400 3-0040: MSP3410D-B4 supports nicam, mode is autodetect
[ 18.172000] bttv0: i2c: checking for TDA9875 @ 0xb0... not found
[ 18.176000] bttv0: i2c: checking for TDA7432 @ 0x8a... not found
[ 18.200000] DVB: registering new adapter (saa7133[0]).
[ 18.200000] DVB: registering frontend 0 (Philips TDA10046H DVB-T)...
[ 18.204000] bttv0: i2c: checking for TDA9887 @ 0x86... not found
[ 18.208000] bttv0: registered device video1
[ 18.208000] bttv0: registered device vbi1
[ 18.208000] bttv0: registered device radio1
[ 18.220000] bttv0: PLL: 28636363 => 35468950 .. ok
[ 18.256000] ACPI: PCI Interrupt Link [AAZA] enabled at IRQ 22
[ 18.256000] ACPI: PCI Interrupt 0000:00:10.1[B] -> Link [AAZA] -> GSI 22 (level, low) -> IRQ 17
[ 18.256000] PCI: Setting latency timer of device 0000:00:10.1 to 64
[ 18.260000] bt878: AUDIO driver version 0.0.0 loaded
[ 18.276000] tda1004x: setting up plls for 48MHz sampling clock
[ 18.564000] ACPI: PCI Interrupt Link [APC7] enabled at IRQ 16
[ 18.564000] ACPI: PCI Interrupt 0000:00:05.0[A] -> Link [APC7] -> GSI 16 (level, low) -> IRQ 22
[ 18.564000] PCI: Setting latency timer of device 0000:00:05.0 to 64
[ 18.564000] NVRM: loading NVIDIA Linux x86 Kernel Module 1.0-9639 Mon Apr 16 20:20:06 PDT 2007
[ 18.564000] bt878: Bt878 AUDIO function found (0).
[ 18.564000] ACPI: PCI Interrupt 0000:04:08.1[A] -> Link [APC1] -> GSI 16 (level, low) -> IRQ 22
[ 18.564000] bt878_probe: card id=[0x13eb0070], Unknown card.
[ 18.564000] Exiting..
[ 18.564000] ACPI: PCI interrupt for device 0000:04:08.1 disabled
[ 18.564000] bt878: probe of 0000:04:08.1 failed with error -22
[ 18.600000] ACPI: PCI Interrupt 0000:04:08.1[A] -> Link [APC1] -> GSI 16 (level, low) -> IRQ 22
[ 18.784000] lp0: using parport0 (interrupt-driven).
[ 19.064000] it87: Found IT8716F chip at 0x290, revision 1
[ 19.064000] it87: in3 is VCC (+5V)
[ 19.064000] it87: in7 is VCCH (+5V Stand-By)
[ 19.064000] it87-isa 9191-0290: Detected broken BIOS defaults, disabling PWM interface
[ 19.112000] Adding 4883752k swap on /dev/hda2. Priority:-1 extents:1 across:4883752k
[ 19.424000] EXT3 FS on hda1, internal journal
[ 19.740000] SGI XFS with ACLs, security attributes, realtime, large block numbers, no debug enabled
[ 19.740000] SGI XFS Quota Management subsystem
[ 19.788000] XFS mounting filesystem hda3
[ 19.892000] Ending clean XFS mount for filesystem: hda3
[ 20.516000] tda1004x: timeout waiting for DSP ready
[ 20.556000] tda1004x: found firmware revision 0 -- invalid
[ 20.556000] tda1004x: trying to boot from eeprom
[ 20.796000] input: Power Button (FF) as /class/input/input6
[ 20.796000] ACPI: Power Button (FF) [PWRF]
[ 20.796000] input: Power Button (CM) as /class/input/input7
[ 20.796000] ACPI: Power Button (CM) [PWRB]
[ 20.900000] No dock devices found.
[ 21.124000] powernow-k8: Found 2 AMD Athlon(tm) 64 X2 Dual Core Processor 4400+ processors (version 2.00.00)
[ 21.124000] powernow-k8: 0 : fid 0xf (2300 MHz), vid 0x9
[ 21.124000] powernow-k8: 1 : fid 0xe (2200 MHz), vid 0xa
[ 21.124000] powernow-k8: 2 : fid 0xc (2000 MHz), vid 0xc
[ 21.124000] powernow-k8: 3 : fid 0xa (1800 MHz), vid 0xe
[ 21.128000] powernow-k8: 4 : fid 0x2 (1000 MHz), vid 0x12
[ 22.888000] tda1004x: timeout waiting for DSP ready
[ 22.928000] tda1004x: found firmware revision 0 -- invalid
[ 22.928000] tda1004x: waiting for firmware upload...
[ 22.956000] tda1004x: no firmware upload (timeout or file not found?)
[ 22.956000] tda1004x: firmware upload failed
[ 27.588000] NET: Registered protocol family 10
[ 27.588000] lo: Disabled Privacy Extensions
[ 28.064000] ppdev: user-space parallel port driver
[ 28.196000] audit(1201969390.014:3): type=1503 operation="inode_permission" requested_mask="a" denied_mask="a" name="/dev/tty" pid=5765 profile="/usr/sbin/cupsd"
[ 29.872000] apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
[ 29.872000] apm: disabled - APM is not SMP safe.
[ 31.000000] Clocksource tsc unstable (delta = -192129348 ns)
[ 31.388000] Failure registering capabilities with primary security module.
[ 34.740000] Bluetooth: Core ver 2.11
[ 34.740000] NET: Registered protocol family 31
[ 34.740000] Bluetooth: HCI device and connection manager initialized
[ 34.740000] Bluetooth: HCI socket layer initialized
[ 34.840000] Bluetooth: L2CAP ver 2.8
[ 34.840000] Bluetooth: L2CAP socket layer initialized
[ 34.936000] Bluetooth: RFCOMM socket layer initialized
[ 34.936000] Bluetooth: RFCOMM TTY layer initialized
[ 34.936000] Bluetooth: RFCOMM ver 1.8
[ 35.668000] tda9887 3-0042: i2c i/o error: rc == -121 (should be 4)
[ 36.056000] NET: Registered protocol family 17
[ 48.356000] eth0: no IPv6 routers present
[ 102.480000] tda9887 3-0042: i2c i/o error: rc == -121 (should be 4)
[ 102.492000] tda9887 3-0042: i2c i/o error: rc == -121 (should be 4)
[ 102.492000] tda9887 3-0042: i2c i/o error: rc == -121 (should be 4)
[ 102.496000] tda9887 3-0042: i2c i/o error: rc == -121 (should be 4)
[ 102.844000] tda9887 3-0042: i2c i/o error: rc == -121 (should be 4)
[ 102.864000] tda9887 3-0042: i2c i/o error: rc == -121 (should be 4)
[ 234.588000] tda9887 3-0042: i2c i/o error: rc == -121 (should be 4)
[ 234.600000] tda9887 3-0042: i2c i/o error: rc == -121 (should be 4)
[ 234.600000] tda9887 3-0042: i2c i/o error: rc == -121 (should be 4)
[ 234.604000] tda9887 3-0042: i2c i/o error: rc == -121 (should be 4)
[ 234.672000] tda9887 3-0042: i2c i/o error: rc == -121 (should be 4)
[ 234.700000] tda9887 3-0042: i2c i/o error: rc == -121 (should be 4)
[ 245.212000] tda9887 3-0042: i2c i/o error: rc == -121 (should be 4)
--
Fredrik Stax\"ang | rot13: sfgk@hcqngr.hh.fr
This is all you need to know about vi: ESC : q ! RET
--
video4linux-list mailing list
Unsubscribe mailto:video4linux-list-request@redhat.com?subject=unsubscribe
https://www.redhat.com/mailman/listinfo/video4linux-list
^ permalink raw reply [flat|nested] only message in thread
only message in thread, other threads:[~2008-02-03 7:25 UTC | newest]
Thread overview: (only message) (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2008-02-03 7:23 Adding a second card (hvr-1110), video from old card (bt878) stutters Fredrik Staxeng
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.