From: James Mayer <james.mayer@acm.org>
To: linux-kernel@vger.kernel.org
Subject: [bug] 2.4.19-pre4-ac2 hang at boot with ALI15x3 chipset support
Date: Wed, 27 Mar 2002 16:38:12 -0700 [thread overview]
Message-ID: <20020327233812.GA7310@galileo> (raw)
Hi,
I'm seeing a kernel hang at boot with the ALI15x3 driver on a Sony
PCG-C1MV/M with 2.4.19-pre4-ac2.
The kernel hangs right after printing
ALI15X3: chipset revision 196
ALI15X3: not 100% native mode: will probe irqs later
After adding printk calls to alim15x3.c, it seems to hang during the
pci_write_config_byte(isa_dev, 0x79, tmpbyte | 0x02) call on line 588.
The kernel successfully loads if I build without ALI15x3 support,
printing these messages:
ALI15X3: chipset revision 196
ALI15X3: not 100% native mode: will probe irqs later
ALI15X3: simplex device: DMA disabled
ide0: ALI15X3 Bus-Master DMA disabled (BIOS)
ALI15X3: simplex device: DMA disabled
ide1: ALI15X3 Bus-Master DMA disabled (BIOS)
hda: IC25N020ATDA04-0, ATA DISK drive
Is the ALI15x3 driver falsely enabling udma on my system?
ide0=nodma doesn't help, either...
I'm appending the output from lspci -vv in case that helps.
Thanks for any help...
- James
00:00.0 Host bridge: Transmeta Corporation LongRun Northbridge (rev 01)
Subsystem: Sony Corporation: Unknown device 80ec
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Region 0: Memory at e8000000 (32-bit, non-prefetchable) [size=1M]
00:00.1 RAM memory: Transmeta Corporation SDRAM controller
Subsystem: Sony Corporation: Unknown device 80ec
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:00.2 RAM memory: Transmeta Corporation BIOS scratchpad
Subsystem: Sony Corporation: Unknown device 80ec
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:06.0 Multimedia audio controller: Acer Laboratories Inc. [ALi] M5451 PCI South Bridge Audio (rev 02)
Subsystem: Sony Corporation: Unknown device 80ec
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR+ <PERR+
Latency: 64 (500ns min, 6000ns max)
Interrupt: pin A routed to IRQ 9
Region 0: I/O ports at 1800 [size=256]
Region 1: Memory at e8100000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <available only to root>
00:07.0 ISA bridge: Acer Laboratories Inc. [ALi] M1533 PCI to ISA Bridge [Aladdin IV]
Subsystem: Sony Corporation: Unknown device 80ec
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: <available only to root>
00:08.0 Modem: Acer Laboratories Inc. [ALi]: Unknown device 5457 (prog-if 00 [Generic])
Subsystem: Sony Corporation: Unknown device 80ec
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 9
Region 0: Memory at e8101000 (32-bit, non-prefetchable) [disabled] [size=4K]
Region 1: I/O ports at 1c00 [disabled] [size=256]
Capabilities: <available only to root>
00:09.0 FireWire (IEEE 1394): Texas Instruments: Unknown device 8021 (rev 02) (prog-if 10 [OHCI])
Subsystem: Sony Corporation: Unknown device 80ec
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (750ns min, 1000ns max), cache line size 08
Interrupt: pin A routed to IRQ 9
Region 0: Memory at e8102000 (32-bit, non-prefetchable) [size=2K]
Region 1: Memory at e8104000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <available only to root>
00:0a.0 Multimedia controller: Citicorp TTI: Unknown device 2011
Subsystem: Sony Corporation: Unknown device 80ec
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 9
Region 0: I/O ports at 2000 [disabled] [size=256]
Region 1: Memory at e8200000 (32-bit, non-prefetchable) [disabled] [size=1M]
Capabilities: <available only to root>
00:0b.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139 (rev 10)
Subsystem: Sony Corporation: Unknown device 80ec
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 9
Region 0: I/O ports at 2400 [size=256]
Region 1: Memory at e8102800 (32-bit, non-prefetchable) [size=256]
Capabilities: <available only to root>
00:0c.0 VGA compatible controller: ATI Technologies Inc Radeon Mobility M6 LY (prog-if 00 [VGA])
Subsystem: Sony Corporation: Unknown device 80ec
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 9
Region 0: Memory at f0000000 (32-bit, prefetchable) [size=128M]
Region 1: I/O ports at 2800 [size=256]
Region 2: Memory at e8110000 (32-bit, non-prefetchable) [size=64K]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: <available only to root>
00:0f.0 USB Controller: Acer Laboratories Inc. [ALi] M5237 USB (rev 03) (prog-if 10 [OHCI])
Subsystem: Sony Corporation: Unknown device 80ec
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 9
Region 0: Memory at e8103000 (32-bit, non-prefetchable) [disabled] [size=4K]
Capabilities: <available only to root>
00:10.0 IDE interface: Acer Laboratories Inc. [ALi] M5229 IDE (rev c4) (prog-if a0)
Subsystem: Sony Corporation: Unknown device 80ec
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (500ns min, 1000ns max)
Interrupt: pin A routed to IRQ 0
Region 0: [virtual] I/O ports at 01f0 [size=16]
Region 1: [virtual] I/O ports at 03f4
Region 2: [virtual] I/O ports at 0170 [size=16]
Region 3: [virtual] I/O ports at 0374
Region 4: I/O ports at 1400 [size=16]
Capabilities: <available only to root>
00:11.0 Non-VGA unclassified device: Acer Laboratories Inc. [ALi] M7101 PMU
Subsystem: Sony Corporation: Unknown device 80ec
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:12.0 CardBus bridge: Ricoh Co Ltd RL5c475 (rev 80)
Subsystem: Sony Corporation: Unknown device 80ec
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168
Interrupt: pin A routed to IRQ 9
Region 0: Memory at 10000000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=01, subordinate=01, sec-latency=176
Memory window 0: 10400000-107ff000 (prefetchable)
Memory window 1: 10800000-10bff000
I/O window 0: 00004000-000040ff
I/O window 1: 00004400-000044ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
00:14.0 USB Controller: Acer Laboratories Inc. [ALi] M5237 USB (rev 03) (prog-if 10 [OHCI])
Subsystem: Sony Corporation: Unknown device 80ec
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (20000ns max), cache line size 08
Interrupt: pin A routed to IRQ 9
Region 0: Memory at 000e0000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <available only to root>
next reply other threads:[~2002-03-27 23:36 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
2002-03-27 23:38 James Mayer [this message]
2002-03-27 23:52 ` [bug] 2.4.19-pre4-ac2 hang at boot with ALI15x3 chipset support Brian D Heaton
2002-03-27 23:59 ` Andre Hedrick
2002-03-28 0:04 ` Alan Cox
2002-03-28 0:21 ` James Mayer
2002-03-28 0:30 ` Andre Hedrick
[not found] <86387368@toto.iv>
2002-03-28 3:37 ` bhoward
2002-03-29 1:08 ` James Mayer
[not found] <124088188@toto.iv>
2002-03-29 10:01 ` bhoward
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20020327233812.GA7310@galileo \
--to=james.mayer@acm.org \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.