From: Jesse Pollard <pollard@tomcat.admin.navo.hpc.mil>
To: viro@math.psu.edu, Jesse Pollard <pollard@tomcat.admin.navo.hpc.mil>
Cc: mark@mark.mielke.cc, elladan@eskimo.com,
Christoph Hellwig <hch@infradead.org>,
Linux-Kernel <linux-kernel@vger.kernel.org>
Subject: Re: [RFC] ext2 and ext3 block reservations can be bypassed
Date: Tue, 14 May 2002 14:29:33 -0500 (CDT) [thread overview]
Message-ID: <200205141929.OAA81537@tomcat.admin.navo.hpc.mil> (raw)
--------- Received message begins Here ---------
>
>
>
> On Tue, 14 May 2002, Jesse Pollard wrote:
>
> > However, not all daemons run as root, but do log into /var/adm or /var/log.
> > If these fill up the log device without restraint, then your audit logs will
> > ALSO be affected (unless you have syslog send them to a different host).
>
> syslogd _does_ run as root and it can happily overflow the damn thing,
> reserved blocks or not.
>
Absolutely - and it should, since that IS the primary audit log daemon.
I don't consider that a "bug". Only if a "user" process (non-root, or
non-designated user) can exceed the set bounds, by either appending, or
filling in a hole, should there be a bug in the system.
Personally, I think ext2 works great. (And I DON'T count the time experimental
code with the warning "caution, may be hazardous to your filesystem" as
causing problems - I had expected it to.)
I've never had a problem with ext2, even when I did fill the filesystem.
I was able to log in and view the audit log, and clean up without
problems - exactly as I would expect.
It has been the most stable file system I've ever used (and I've used
quite a few - old Files-11 and Files-32, RT11, dos, UFS, UNICOS nc1, SGI
efs and xfs ...)
Easier fsck procedure than all of them. Fixed any inconsistancies as well
and didn't loose any resident files.
I've only lost one ext2fs - and that was due to a head crash. The drive
had been running for a couple of years continuously, with only a few
mis-guided reboots.
-------------------------------------------------------------------------
Jesse I Pollard, II
Email: pollard@navo.hpc.mil
Any opinions expressed are solely my own.
next reply other threads:[~2002-05-14 19:29 UTC|newest]
Thread overview: 32+ messages / expand[flat|nested] mbox.gz Atom feed top
2002-05-14 19:29 Jesse Pollard [this message]
-- strict thread matches above, loose matches on Subject: below --
2002-05-14 18:54 [RFC] ext2 and ext3 block reservations can be bypassed Jesse Pollard
2002-05-14 19:04 ` Alexander Viro
2002-05-14 19:55 ` Mark Mielke
2002-05-14 18:07 Jesse Pollard
2002-05-14 18:00 Jesse Pollard
2002-05-14 17:53 Jesse Pollard
2002-05-14 18:23 ` Mark Mielke
2002-05-14 19:11 ` Alexander Viro
[not found] <791836807@toto.iv>
2002-05-12 22:04 ` Peter Chubb
2002-05-12 22:53 ` Alexander Viro
2002-05-13 4:22 ` Kasper Dupont
2002-05-13 4:51 ` Elladan
2002-05-12 16:23 Kasper Dupont
2002-05-12 16:42 ` Jakob Østergaard
2002-05-12 17:34 ` Elladan
2002-05-12 18:15 ` Alexander Viro
2002-05-12 18:37 ` Elladan
2002-05-12 19:02 ` Jakob Østergaard
2002-05-12 19:04 ` Mark Mielke
2002-05-13 17:09 ` Horst von Brand
2002-05-13 17:52 ` Elladan
2002-05-13 17:57 ` Christoph Hellwig
2002-05-14 16:22 ` Elladan
2002-05-14 16:55 ` Mark Mielke
2002-05-14 17:47 ` Elladan
2002-05-14 18:51 ` Kasper Dupont
2002-05-15 19:48 ` Pavel Machek
2002-05-15 20:29 ` Alan Cox
2002-05-14 15:40 ` Kasper Dupont
2002-05-14 15:56 ` Mark Mielke
2002-05-14 18:25 ` Kasper Dupont
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=200205141929.OAA81537@tomcat.admin.navo.hpc.mil \
--to=pollard@tomcat.admin.navo.hpc.mil \
--cc=elladan@eskimo.com \
--cc=hch@infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=mark@mark.mielke.cc \
--cc=viro@math.psu.edu \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.