* aic7(censored) dying horribly in 2.5.65-mm2 (fwd)
@ 2003-03-21 7:17 Zwane Mwaikambo
2003-03-21 7:18 ` Zwane Mwaikambo
` (2 more replies)
0 siblings, 3 replies; 7+ messages in thread
From: Zwane Mwaikambo @ 2003-03-21 7:17 UTC (permalink / raw)
To: Linux Kernel
Hi Justin i got this booting 2.5.65-mm2, 2.5.65 was fine there is an oops
right at the end. Is there anything specific you want?
01:0d.0 SCSI storage controller: Adaptec AHA-294x / AIC-7870 (rev 03)
01:0e.0 SCSI storage controller: Adaptec AHA-294x / AIC-7870 (rev 03)
There are 6 spindles on that second HBA, and a DLT and CDROM on the first.
CONFIG_SCSI_AIC7XXX=y
CONFIG_AIC7XXX_CMDS_PER_DEVICE=253
CONFIG_AIC7XXX_RESET_DELAY_MS=15000
# CONFIG_AIC7XXX_PROBE_EISA_VL is not set
# CONFIG_AIC7XXX_BUILD_FIRMWARE is not set
CONFIG_AIC7XXX_DEBUG_ENABLE=y
CONFIG_AIC7XXX_DEBUG_MASK=0
CONFIG_AIC7XXX_REG_PRETTY_PRINT=y
# CONFIG_SCSI_AIC7XXX_OLD is not set
Starting NFS statd: [ OK ]
Loading keymap: scsi1:0:0:0: Attempting to queue an ABORT message
>>>>>>>>>>>>>>>>>> Dump Card State Begins <<<<<<<<<<<<<<<<<
scsi1: Dumping Card State while idle, at SEQADDR 0x8
Card was paused
ACCUM = 0x55, SINDEX = 0xa, DINDEX = 0x8c, ARG_2 = 0x0
HCNT = 0x0 SCBPTR = 0x8
SCSISIGI[0xe6]:(REQI|BSYI|MSGI|IOI|CDI) ERROR[0x40]:(PCIERRSTAT)
SCSIBUSL[0x80] LASTPHASE[0x1]:(P_BUSFREE)
SCSISEQ[0x12]:(ENAUTOATNP|ENRSELI)
SBLKCTL[0x2]:(SELWIDE) SCSIRATE[0x0] SEQCTL[0x10]:(FASTMODE)
SEQ_FLAGS[0xc0]:(NO_CDB_SENT|NOT_IDENTIFIED)
SSTAT0[0x25]:(DMADONE|SDONE|SELDI)
SSTAT1[0xb]:(REQINIT|PHASECHG|BUSFREE) SSTAT2[0x0]
SSTAT3[0x0] SIMODE0[0x0] SIMODE1[0xa4]:(ENSCSIPERR|ENSCSIRST|ENSELTIMO)
SXFRCTL0[0x80]:(DFON) DFCNTRL[0x0]
DFSTATUS[0x29]:(FIFOEMP|HDONE|FIFOQWDEMP)
STACK: 0x0 0x169 0x10c 0x3
SCB count = 56
Kernel NEXTQSCB = 8
Card NEXTQSCB = 8
QINFIFO entries:
Waiting Queue entries:
Disconnected Queue entries: 0:13
QOUTFIFO entries:
Sequencer Free SCB List: 8 3 2 9 13 5 6 4 14 7 1 11 12 10 15
Sequencer SCB Info:
0 SCB_CONTROL[0x64]:(DISCONNECTED|TAG_ENB|DISCENB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xd]
1 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
2 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
3 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
4 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
5 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
6 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
7 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
8 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
9 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
10 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
11 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
12 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
13 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
14 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
15 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
Pending list:
13 SCB_CONTROL[0x60]:(TAG_ENB|DISCENB) SCB_SCSIID[0x7] SCB_LUN[0x0]
Kernel Free SCB list: 10 11 0 25 41 28 31 40 45 29 30 46 47 24 26 5 20 21
42 43 27 23 22 49 50 36 37 3 48 4 1 7 18 44 35
DevQ(0:0:0): 0 waiting
DevQ(0:1:0): 0 waiting
DevQ(0:2:0): 0 waiting
DevQ(0:3:0): 0 waiting
DevQ(0:4:0): 0 waiting
DevQ(0:5:0): 0 waiting
<<<<<<<<<<<<<<<<< Dump Card State Ends >>>>>>>>>>>>>>>>>>
(scsi1:A:0:0): Device is disconnected, re-queuing SCB
Recovery code sleeping
(scsi1:A:0:0): Abort Tag Message Sent
(scsi1:A:0:0): SCB 13 - Abort Tag Completed.
Recovery SCB completes
Recovery code awake
aic7xxx_abort returns 0x2002
scsi1:0:0:0: Attempting to queue an ABORT message
scsi1:0:0:0: Command not found
aic7xxx_abort returns 0x2002
scsi1:0:0:0: Attempting to queue an ABORT message
scsi1:0:0:0: Command not found
aic7xxx_abort returns 0x2002
[ OK ]
Loading system font: scsi1:0:0:0: Attempting to queue an ABORT message
scsi1:0:0:0: Command not found
aic7xxx_abort returns 0x2002
scsi1:0:0:0: Attempting to queue an ABORT message
scsi1:0:0:0: Command not found
aic7xxx_abort returns 0x2002
scsi1:0:0:0: Attempting to queue an ABORT message
scsi1:0:0:0: Command not found
aic7xxx_abort returns 0x2002
scsi1:0:0:0: Attempting to queue a TARGET RESET message
scsi1:0:0:0: Command not found
aic7xxx_dev_reset returns 0x2002
scsi1:0:0:0: Attempting to queue an ABORT message
scsi1:0:0:0: Command not found
aic7xxx_abort returns 0x2002
scsi1:0:0:0: Attempting to queue an ABORT message
>>>>>>>>>>>>>>>>>> Dump Card State Begins <<<<<<<<<<<<<<<<<
scsi1: Dumping Card State while idle, at SEQADDR 0x8
Card was paused
ACCUM = 0xea, SINDEX = 0x64, DINDEX = 0x65, ARG_2 = 0xa
HCNT = 0x0 SCBPTR = 0x4
SCSISIGI[0x0] ERROR[0x40]:(PCIERRSTAT) SCSIBUSL[0x0]
LASTPHASE[0x1]:(P_BUSFREE) SCSISEQ[0x12]:(ENAUTOATNP|ENRSELI)
SBLKCTL[0x2]:(SELWIDE) SCSIRATE[0x0] SEQCTL[0x10]:(FASTMODE)
SEQ_FLAGS[0xc0]:(NO_CDB_SENT|NOT_IDENTIFIED) SSTAT0[0x5]:(DMADONE|SDONE)
SSTAT1[0xa]:(PHASECHG|BUSFREE) SSTAT2[0x0] SSTAT3[0x0]
SIMODE0[0x0] SIMODE1[0xa4]:(ENSCSIPERR|ENSCSIRST|ENSELTIMO)
SXFRCTL0[0x80]:(DFON) DFCNTRL[0x0]
DFSTATUS[0x2d]:(FIFOEMP|DFTHRESH|HDONE|FIFOQWDEMP)
STACK: 0xe4 0x169 0x199 0x3
SCB count = 56
Kernel NEXTQSCB = 8
Card NEXTQSCB = 8
QINFIFO entries:
Waiting Queue entries:
Disconnected Queue entries: 4:43
QOUTFIFO entries:
Sequencer Free SCB List: 0 2 12 11 14 7 1 15 10 3 9 13 6 5 8
Sequencer SCB Info:
0 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
1 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
2 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
3 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
4 SCB_CONTROL[0x64]:(DISCONNECTED|TAG_ENB|DISCENB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0x2b]
5 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
6 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
7 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
8 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
9 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
10 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
11 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
12 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
13 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
14 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
15 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
Pending list:
43 SCB_CONTROL[0x60]:(TAG_ENB|DISCENB) SCB_SCSIID[0x7] SCB_LUN[0x0]
Kernel Free SCB list: 31 44 46 30 40 45 29 3 24 23 37 47 20 21 5 42 27 26
50 22 49 36 1 4 48 18 11 10 7 0 25 28 41 13 35
DevQ(0:0:0): 0 waiting
DevQ(0:1:0): 0 waiting
DevQ(0:2:0): 0 waiting
DevQ(0:3:0): 0 waiting
DevQ(0:4:0): 0 waiting
DevQ(0:5:0): 0 waiting
<<<<<<<<<<<<<<<<< Dump Card State Ends >>>>>>>>>>>>>>>>>>
(scsi1:A:0:0): Device is disconnected, re-queuing SCB
(scsi1:A:0:0): Recovery code sleeping
Abort Tag Message Sent
Recovery code awake
Timer Expired
aic7xxx_abort returns 0x2003
SCSI disk error : host 1 channel 0 id 0 lun 0 return code = 6000000
end_request: I/O error, dev sda, sector 133984
Buffer I/O error on device sd(8,1), logical block 16744
SCSI disk error : host 1 channel 0 id 0 lun 0 return code = 6000000
end_request: I/O error, dev sda, sector 4980800
Buffer I/O error on device sd(8,1), logical block 622596
Debug: sleeping function called from illegal context at
include/linux/rwsem.h:43
Call Trace:
[<c011ed18>] __might_sleep+0x58/0x60
[<c028ec00>] __bdevname+0x50/0xc0
[<c015cb41>] buffer_io_error+0x11/0x30
[<c015d406>] end_buffer_async_write+0x166/0x190
[<c0160101>] end_bio_bh_io_sync+0x21/0x30
[<c0161515>] bio_endio+0x35/0x60
[<c028df8f>] __end_that_request_first+0x1ff/0x220
[<c028dfc7>] end_that_request_first+0x17/0x20
[<c028a864>] elv_next_request+0x84/0xe0
[<c02e187f>] scsi_request_fn+0x3f/0x2a0
[<c028c442>] __blk_run_queue+0x12/0x20
[<c02e022d>] scsi_restart_operations+0xbd/0x120
[<c02e05b8>] scsi_error_handler+0x138/0x1a0
[<c02e0480>] scsi_error_handler+0x0/0x1a0
[<c0107095>] kernel_thread_helper+0x5/0x10
Buffer I/O error on device sd(8,1), logical block 557066
(scsi1:A:0:0): SCB 43 - Abort Tag Completed.
Recovery SCB completes
Unable to handle kernel paging request at virtual address 6b6b6b6b
printing eip:
6b6b6b6b
*pde = 00000000
Oops: 0000 [#1]
CPU: 1
EIP: 0060:[<6b6b6b6b>] Not tainted
EFLAGS: 00010002 VLI
EIP is at 0x6b6b6b6b
eax: cbb1ccf8 ebx: 00000000 ecx: cbe31290 edx: 00000000
esi: 00000001 edi: c1509f20 ebp: 00000005 esp: c1509ea0
ds: 007b es: 007b ss: 0068
Process swapper (pid: 0, threadinfo=c1508000 task=c150a660)
Stack: c02ff78c cbb1ccf8 cbb1ccf8 cbe31290 c0305c07 cbe31290 cbb1ccf8 00000292
3e7ac717 c17e848c cbffe4f4 04000001 c010bb0d 00000005 cbe31290 c1509f20
c05060a0 c1508000 c1508000 00000005 c010be49 00000005 c1509f20 cbffe4f4
Call Trace:
[<c02ff78c>] ahc_linux_run_complete_queue+0x3c/0x50
[<c0305c07>] ahc_linux_isr+0x1d7/0x3a0
[<c010bb0d>] handle_IRQ_event+0x2d/0x50
[<c010be49>] do_IRQ+0x109/0x210
[<c010a398>] common_interrupt+0x18/0x20
[<c01264f6>] do_softirq+0x56/0xc0
[<c01168a5>] smp_apic_timer_interrupt+0xf5/0x160
[<c0106ea0>] default_idle+0x0/0x40
[<c010a41a>] apic_timer_interrupt+0x1a/0x20
[<c0106ea0>] default_idle+0x0/0x40
[<c0106ece>] default_idle+0x2e/0x40
[<c0106f5a>] cpu_idle+0x3a/0x50
[<c01226fd>] release_console_sem+0xbd/0x170
[<c012256b>] printk+0x1eb/0x270
Code: Bad EIP value.
<0>Kernel panic: Aiee, killing interrupt handler!
In interrupt handler - not syncing
^ permalink raw reply [flat|nested] 7+ messages in thread* Re: aic7(censored) dying horribly in 2.5.65-mm2 (fwd)
2003-03-21 7:17 aic7(censored) dying horribly in 2.5.65-mm2 (fwd) Zwane Mwaikambo
@ 2003-03-21 7:18 ` Zwane Mwaikambo
2003-03-21 7:45 ` Zwane Mwaikambo
2003-03-21 11:43 ` Jos Hulzink
2 siblings, 0 replies; 7+ messages in thread
From: Zwane Mwaikambo @ 2003-03-21 7:18 UTC (permalink / raw)
To: Linux Kernel
I rebooted and got another one;
Bringing up interface eth0: Unable to handle kernel NULL pointer dereference at virtual address 00000000
*pde = 00000000
Oops: 0000 [#1]
CPU: 1
EIP: 0060:[<c02ea2d9>] Not tainted
EFLAGS: 00010046 VLI
EIP is at ahc_handle_scsiint+0xcc9/0x1130
eax: 00000001 ebx: 00000001 ecx: 00000001 edx: 0000000d
esi: 000000a0 edi: cbe31290 ebp: 00000000 esp: c1509e5c
ds: 007b es: 007b ss: 0068
Process swapper (pid: 0, threadinfo=c1508000 task=c150a660)
Stack: 000000ff 41508b68 00000007 00000000 00000000 c1508000 00000001 41410000
00000000 00000007 00000000 c0580001 00000000 00000000 c0509041 00000001
00000007 00000064 cbe31290 c1509f20 00000005 c0305d14 cbe31290 00000064
Call Trace:
[<c0305d14>] ahc_linux_isr+0x2e4/0x3a0
[<c010bb0d>] handle_IRQ_event+0x2d/0x50
[<c010be49>] do_IRQ+0x109/0x210
[<c010a398>] common_interrupt+0x18/0x20
[<c01264f6>] do_softirq+0x56/0xc0
[<c01168a5>] smp_apic_timer_interrupt+0xf5/0x160
[<c0106ea0>] default_idle+0x0/0x40
[<c010a41a>] apic_timer_interrupt+0x1a/0x20
[<c0106ea0>] default_idle+0x0/0x40
[<c0106ece>] default_idle+0x2e/0x40
[<c0106f5a>] cpu_idle+0x3a/0x50
[<c01226fd>] release_console_sem+0xbd/0x170
[<c012256b>] printk+0x1eb/0x270
Code: ce 80 e3 ff 6a 02 6a 01 8b 44 24 1c 50 8b 44 24 30 50 0f be 44 24 2b
50 8b 44 24 34 50 57 e8 6f af 00 00 83 c4 30
<0>Kernel panic: Aiee, killing interrupt handler!
In interrupt handler - not syncing
--
function.linuxpower.ca
^ permalink raw reply [flat|nested] 7+ messages in thread* Re: aic7(censored) dying horribly in 2.5.65-mm2 (fwd)
2003-03-21 7:17 aic7(censored) dying horribly in 2.5.65-mm2 (fwd) Zwane Mwaikambo
2003-03-21 7:18 ` Zwane Mwaikambo
@ 2003-03-21 7:45 ` Zwane Mwaikambo
2003-03-21 19:56 ` Justin T. Gibbs
2003-03-21 11:43 ` Jos Hulzink
2 siblings, 1 reply; 7+ messages in thread
From: Zwane Mwaikambo @ 2003-03-21 7:45 UTC (permalink / raw)
To: Linux Kernel
On Fri, 21 Mar 2003, Zwane Mwaikambo wrote:
> Hi Justin i got this booting 2.5.65-mm2, 2.5.65 was fine there is an oops
> right at the end. Is there anything specific you want?
Correction, 2.5.65 isn't ok (both aic7xxx and aic7xxx_old die although
aic7xxx not as ceremoniously). I do know that 2.5.53 is ok so i'll try and
find the suspect kernel.
Cheers,
Zwane
--
function.linuxpower.ca
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: aic7(censored) dying horribly in 2.5.65-mm2 (fwd)
2003-03-21 7:45 ` Zwane Mwaikambo
@ 2003-03-21 19:56 ` Justin T. Gibbs
0 siblings, 0 replies; 7+ messages in thread
From: Justin T. Gibbs @ 2003-03-21 19:56 UTC (permalink / raw)
To: Zwane Mwaikambo, Linux Kernel
> On Fri, 21 Mar 2003, Zwane Mwaikambo wrote:
>
>> Hi Justin i got this booting 2.5.65-mm2, 2.5.65 was fine there is an oops
>> right at the end. Is there anything specific you want?
>
> Correction, 2.5.65 isn't ok (both aic7xxx and aic7xxx_old die although
> aic7xxx not as ceremoniously). I do know that 2.5.53 is ok so i'll try and
> find the suspect kernel.
One other thing to consider is if interrupts are working for you with
later kernels. The 2.5.X aic79xx src tarball should work in 2.5.53 and
2.5.65, so if the same driver rev works in one kernel but not the other,
then you can quickly exonerate the driver.
--
Justin
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: aic7(censored) dying horribly in 2.5.65-mm2 (fwd)
2003-03-21 7:17 aic7(censored) dying horribly in 2.5.65-mm2 (fwd) Zwane Mwaikambo
2003-03-21 7:18 ` Zwane Mwaikambo
2003-03-21 7:45 ` Zwane Mwaikambo
@ 2003-03-21 11:43 ` Jos Hulzink
2003-03-21 20:05 ` Justin T. Gibbs
2 siblings, 1 reply; 7+ messages in thread
From: Jos Hulzink @ 2003-03-21 11:43 UTC (permalink / raw)
To: Zwane Mwaikambo, Linux Kernel
Hi
Similar issues here., though I must say the Adaptec driver hasn't worked for
me on all kernels I tried since my first try with 2.5.44. I get almost the
same output with a plain 2.5.65 kernel, though my kernel locks up just before
the crash you get, I get no dmesg output.
Note that it takes ages to get trough the SCSI driver towards the lockup. I
guess some timeouts cause this.
Config is the same, if it matters: SMP enabled.
Bus 0, device 6, function 0:
SCSI storage controller: Adaptec AIC-7880U (rev 0).
Attached are a CD-RW and a tapedrive.
2.4 kernels run fine.
Please let me know if additional details are required.
Jos
> Friday 21 March 2003 08:17, Zwane Mwaikambo wrote:
> Hi Justin i got this booting 2.5.65-mm2, 2.5.65 was fine there is an oops
> right at the end. Is there anything specific you want?
>
> 01:0d.0 SCSI storage controller: Adaptec AHA-294x / AIC-7870 (rev 03)
> 01:0e.0 SCSI storage controller: Adaptec AHA-294x / AIC-7870 (rev 03)
>
> There are 6 spindles on that second HBA, and a DLT and CDROM on the first.
>
> CONFIG_SCSI_AIC7XXX=y
> CONFIG_AIC7XXX_CMDS_PER_DEVICE=253
> CONFIG_AIC7XXX_RESET_DELAY_MS=15000
> # CONFIG_AIC7XXX_PROBE_EISA_VL is not set
> # CONFIG_AIC7XXX_BUILD_FIRMWARE is not set
> CONFIG_AIC7XXX_DEBUG_ENABLE=y
> CONFIG_AIC7XXX_DEBUG_MASK=0
> CONFIG_AIC7XXX_REG_PRETTY_PRINT=y
> # CONFIG_SCSI_AIC7XXX_OLD is not set
>
> Starting NFS statd: [ OK ]
> Loading keymap: scsi1:0:0:0: Attempting to queue an ABORT message
>
> >>>>>>>>>>>>>>>>>> Dump Card State Begins <<<<<<<<<<<<<<<<<
>
> scsi1: Dumping Card State while idle, at SEQADDR 0x8
> Card was paused
> ACCUM = 0x55, SINDEX = 0xa, DINDEX = 0x8c, ARG_2 = 0x0
> HCNT = 0x0 SCBPTR = 0x8
> SCSISIGI[0xe6]:(REQI|BSYI|MSGI|IOI|CDI) ERROR[0x40]:(PCIERRSTAT)
> SCSIBUSL[0x80] LASTPHASE[0x1]:(P_BUSFREE)
> SCSISEQ[0x12]:(ENAUTOATNP|ENRSELI)
> SBLKCTL[0x2]:(SELWIDE) SCSIRATE[0x0] SEQCTL[0x10]:(FASTMODE)
> SEQ_FLAGS[0xc0]:(NO_CDB_SENT|NOT_IDENTIFIED)
> SSTAT0[0x25]:(DMADONE|SDONE|SELDI)
> SSTAT1[0xb]:(REQINIT|PHASECHG|BUSFREE) SSTAT2[0x0]
> SSTAT3[0x0] SIMODE0[0x0] SIMODE1[0xa4]:(ENSCSIPERR|ENSCSIRST|ENSELTIMO)
> SXFRCTL0[0x80]:(DFON) DFCNTRL[0x0]
> DFSTATUS[0x29]:(FIFOEMP|HDONE|FIFOQWDEMP)
> STACK: 0x0 0x169 0x10c 0x3
> SCB count = 56
> Kernel NEXTQSCB = 8
> Card NEXTQSCB = 8
> QINFIFO entries:
> Waiting Queue entries:
> Disconnected Queue entries: 0:13
> QOUTFIFO entries:
> Sequencer Free SCB List: 8 3 2 9 13 5 6 4 14 7 1 11 12 10 15
> Sequencer SCB Info:
> 0 SCB_CONTROL[0x64]:(DISCONNECTED|TAG_ENB|DISCENB) SCB_SCSIID[0x7]
> SCB_LUN[0x0] SCB_TAG[0xd]
> 1 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
> SCB_LUN[0x0] SCB_TAG[0xff]
> 2 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
> SCB_LUN[0x0] SCB_TAG[0xff]
> 3 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
> SCB_LUN[0x0] SCB_TAG[0xff]
> 4 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
> SCB_LUN[0x0] SCB_TAG[0xff]
> 5 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
> SCB_LUN[0x0] SCB_TAG[0xff]
> 6 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
> SCB_LUN[0x0] SCB_TAG[0xff]
> 7 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
> SCB_LUN[0x0] SCB_TAG[0xff]
> 8 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
> SCB_LUN[0x0] SCB_TAG[0xff]
> 9 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
> SCB_LUN[0x0] SCB_TAG[0xff]
> 10 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
> SCB_LUN[0x0] SCB_TAG[0xff]
> 11 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
> SCB_LUN[0x0] SCB_TAG[0xff]
> 12 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
> SCB_LUN[0x0] SCB_TAG[0xff]
> 13 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
> SCB_LUN[0x0] SCB_TAG[0xff]
> 14 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
> SCB_LUN[0x0] SCB_TAG[0xff]
> 15 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
> SCB_LUN[0x0] SCB_TAG[0xff]
> Pending list:
> 13 SCB_CONTROL[0x60]:(TAG_ENB|DISCENB) SCB_SCSIID[0x7] SCB_LUN[0x0]
> Kernel Free SCB list: 10 11 0 25 41 28 31 40 45 29 30 46 47 24 26 5 20 21
> 42 43 27 23 22 49 50 36 37 3 48 4 1 7 18 44 35
> DevQ(0:0:0): 0 waiting
> DevQ(0:1:0): 0 waiting
> DevQ(0:2:0): 0 waiting
> DevQ(0:3:0): 0 waiting
> DevQ(0:4:0): 0 waiting
> DevQ(0:5:0): 0 waiting
>
> <<<<<<<<<<<<<<<<< Dump Card State Ends >>>>>>>>>>>>>>>>>>
> (scsi1:A:0:0): Device is disconnected, re-queuing SCB
> Recovery code sleeping
> (scsi1:A:0:0): Abort Tag Message Sent
> (scsi1:A:0:0): SCB 13 - Abort Tag Completed.
> Recovery SCB completes
> Recovery code awake
> aic7xxx_abort returns 0x2002
> scsi1:0:0:0: Attempting to queue an ABORT message
> scsi1:0:0:0: Command not found
> aic7xxx_abort returns 0x2002
> scsi1:0:0:0: Attempting to queue an ABORT message
> scsi1:0:0:0: Command not found
> aic7xxx_abort returns 0x2002
> [ OK ]
> Loading system font: scsi1:0:0:0: Attempting to queue an ABORT message
> scsi1:0:0:0: Command not found
> aic7xxx_abort returns 0x2002
> scsi1:0:0:0: Attempting to queue an ABORT message
> scsi1:0:0:0: Command not found
> aic7xxx_abort returns 0x2002
> scsi1:0:0:0: Attempting to queue an ABORT message
> scsi1:0:0:0: Command not found
> aic7xxx_abort returns 0x2002
> scsi1:0:0:0: Attempting to queue a TARGET RESET message
> scsi1:0:0:0: Command not found
> aic7xxx_dev_reset returns 0x2002
> scsi1:0:0:0: Attempting to queue an ABORT message
> scsi1:0:0:0: Command not found
> aic7xxx_abort returns 0x2002
> scsi1:0:0:0: Attempting to queue an ABORT message
>
> >>>>>>>>>>>>>>>>>> Dump Card State Begins <<<<<<<<<<<<<<<<<
>
> scsi1: Dumping Card State while idle, at SEQADDR 0x8
> Card was paused
> ACCUM = 0xea, SINDEX = 0x64, DINDEX = 0x65, ARG_2 = 0xa
> HCNT = 0x0 SCBPTR = 0x4
> SCSISIGI[0x0] ERROR[0x40]:(PCIERRSTAT) SCSIBUSL[0x0]
> LASTPHASE[0x1]:(P_BUSFREE) SCSISEQ[0x12]:(ENAUTOATNP|ENRSELI)
> SBLKCTL[0x2]:(SELWIDE) SCSIRATE[0x0] SEQCTL[0x10]:(FASTMODE)
> SEQ_FLAGS[0xc0]:(NO_CDB_SENT|NOT_IDENTIFIED) SSTAT0[0x5]:(DMADONE|SDONE)
> SSTAT1[0xa]:(PHASECHG|BUSFREE) SSTAT2[0x0] SSTAT3[0x0]
> SIMODE0[0x0] SIMODE1[0xa4]:(ENSCSIPERR|ENSCSIRST|ENSELTIMO)
> SXFRCTL0[0x80]:(DFON) DFCNTRL[0x0]
> DFSTATUS[0x2d]:(FIFOEMP|DFTHRESH|HDONE|FIFOQWDEMP)
> STACK: 0xe4 0x169 0x199 0x3
> SCB count = 56
> Kernel NEXTQSCB = 8
> Card NEXTQSCB = 8
> QINFIFO entries:
> Waiting Queue entries:
> Disconnected Queue entries: 4:43
> QOUTFIFO entries:
> Sequencer Free SCB List: 0 2 12 11 14 7 1 15 10 3 9 13 6 5 8
> Sequencer SCB Info:
> 0 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
> SCB_LUN[0x0] SCB_TAG[0xff]
> 1 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
> SCB_LUN[0x0] SCB_TAG[0xff]
> 2 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
> SCB_LUN[0x0] SCB_TAG[0xff]
> 3 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
> SCB_LUN[0x0] SCB_TAG[0xff]
> 4 SCB_CONTROL[0x64]:(DISCONNECTED|TAG_ENB|DISCENB) SCB_SCSIID[0x7]
> SCB_LUN[0x0] SCB_TAG[0x2b]
> 5 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
> SCB_LUN[0x0] SCB_TAG[0xff]
> 6 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
> SCB_LUN[0x0] SCB_TAG[0xff]
> 7 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
> SCB_LUN[0x0] SCB_TAG[0xff]
> 8 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
> SCB_LUN[0x0] SCB_TAG[0xff]
> 9 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
> SCB_LUN[0x0] SCB_TAG[0xff]
> 10 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
> SCB_LUN[0x0] SCB_TAG[0xff]
> 11 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
> SCB_LUN[0x0] SCB_TAG[0xff]
> 12 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
> SCB_LUN[0x0] SCB_TAG[0xff]
> 13 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
> SCB_LUN[0x0] SCB_TAG[0xff]
> 14 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
> SCB_LUN[0x0] SCB_TAG[0xff]
> 15 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
> SCB_LUN[0x0] SCB_TAG[0xff]
> Pending list:
> 43 SCB_CONTROL[0x60]:(TAG_ENB|DISCENB) SCB_SCSIID[0x7] SCB_LUN[0x0]
> Kernel Free SCB list: 31 44 46 30 40 45 29 3 24 23 37 47 20 21 5 42 27 26
> 50 22 49 36 1 4 48 18 11 10 7 0 25 28 41 13 35
> DevQ(0:0:0): 0 waiting
> DevQ(0:1:0): 0 waiting
> DevQ(0:2:0): 0 waiting
> DevQ(0:3:0): 0 waiting
> DevQ(0:4:0): 0 waiting
> DevQ(0:5:0): 0 waiting
>
> <<<<<<<<<<<<<<<<< Dump Card State Ends >>>>>>>>>>>>>>>>>>
> (scsi1:A:0:0): Device is disconnected, re-queuing SCB
> (scsi1:A:0:0): Recovery code sleeping
> Abort Tag Message Sent
> Recovery code awake
> Timer Expired
> aic7xxx_abort returns 0x2003
> SCSI disk error : host 1 channel 0 id 0 lun 0 return code = 6000000
> end_request: I/O error, dev sda, sector 133984
> Buffer I/O error on device sd(8,1), logical block 16744
> SCSI disk error : host 1 channel 0 id 0 lun 0 return code = 6000000
> end_request: I/O error, dev sda, sector 4980800
> Buffer I/O error on device sd(8,1), logical block 622596
> Debug: sleeping function called from illegal context at
> include/linux/rwsem.h:43
> Call Trace:
> [<c011ed18>] __might_sleep+0x58/0x60
> [<c028ec00>] __bdevname+0x50/0xc0
> [<c015cb41>] buffer_io_error+0x11/0x30
> [<c015d406>] end_buffer_async_write+0x166/0x190
> [<c0160101>] end_bio_bh_io_sync+0x21/0x30
> [<c0161515>] bio_endio+0x35/0x60
> [<c028df8f>] __end_that_request_first+0x1ff/0x220
> [<c028dfc7>] end_that_request_first+0x17/0x20
> [<c028a864>] elv_next_request+0x84/0xe0
> [<c02e187f>] scsi_request_fn+0x3f/0x2a0
> [<c028c442>] __blk_run_queue+0x12/0x20
> [<c02e022d>] scsi_restart_operations+0xbd/0x120
> [<c02e05b8>] scsi_error_handler+0x138/0x1a0
> [<c02e0480>] scsi_error_handler+0x0/0x1a0
> [<c0107095>] kernel_thread_helper+0x5/0x10
> Buffer I/O error on device sd(8,1), logical block 557066
> (scsi1:A:0:0): SCB 43 - Abort Tag Completed.
> Recovery SCB completes
>
> Unable to handle kernel paging request at virtual address 6b6b6b6b
> printing eip:
> 6b6b6b6b
> *pde = 00000000
> Oops: 0000 [#1]
> CPU: 1
> EIP: 0060:[<6b6b6b6b>] Not tainted
> EFLAGS: 00010002 VLI
> EIP is at 0x6b6b6b6b
> eax: cbb1ccf8 ebx: 00000000 ecx: cbe31290 edx: 00000000
> esi: 00000001 edi: c1509f20 ebp: 00000005 esp: c1509ea0
> ds: 007b es: 007b ss: 0068
> Process swapper (pid: 0, threadinfo=c1508000 task=c150a660)
> Stack: c02ff78c cbb1ccf8 cbb1ccf8 cbe31290 c0305c07 cbe31290 cbb1ccf8
> 00000292 3e7ac717 c17e848c cbffe4f4 04000001 c010bb0d 00000005 cbe31290
> c1509f20 c05060a0 c1508000 c1508000 00000005 c010be49 00000005 c1509f20
> cbffe4f4 Call Trace:
> [<c02ff78c>] ahc_linux_run_complete_queue+0x3c/0x50
> [<c0305c07>] ahc_linux_isr+0x1d7/0x3a0
> [<c010bb0d>] handle_IRQ_event+0x2d/0x50
> [<c010be49>] do_IRQ+0x109/0x210
> [<c010a398>] common_interrupt+0x18/0x20
> [<c01264f6>] do_softirq+0x56/0xc0
> [<c01168a5>] smp_apic_timer_interrupt+0xf5/0x160
> [<c0106ea0>] default_idle+0x0/0x40
> [<c010a41a>] apic_timer_interrupt+0x1a/0x20
> [<c0106ea0>] default_idle+0x0/0x40
> [<c0106ece>] default_idle+0x2e/0x40
> [<c0106f5a>] cpu_idle+0x3a/0x50
> [<c01226fd>] release_console_sem+0xbd/0x170
> [<c012256b>] printk+0x1eb/0x270
>
> Code: Bad EIP value.
> <0>Kernel panic: Aiee, killing interrupt handler!
> In interrupt handler - not syncing
>
> -
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at http://www.tux.org/lkml/
^ permalink raw reply [flat|nested] 7+ messages in thread* Re: aic7(censored) dying horribly in 2.5.65-mm2 (fwd)
2003-03-21 11:43 ` Jos Hulzink
@ 2003-03-21 20:05 ` Justin T. Gibbs
2003-03-22 0:04 ` Jos Hulzink
0 siblings, 1 reply; 7+ messages in thread
From: Justin T. Gibbs @ 2003-03-21 20:05 UTC (permalink / raw)
To: Jos Hulzink, Zwane Mwaikambo, Linux Kernel
> Hi
>
> Similar issues here., though I must say the Adaptec driver hasn't worked for
> me on all kernels I tried since my first try with 2.5.44. I get almost the
> same output with a plain 2.5.65 kernel, though my kernel locks up just before
> the crash you get, I get no dmesg output.
>
> Note that it takes ages to get trough the SCSI driver towards the lockup. I
> guess some timeouts cause this.
What kind of MB are you using? It sounds like interrupts aren't working
for you.
--
Justin
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: aic7(censored) dying horribly in 2.5.65-mm2 (fwd)
2003-03-21 20:05 ` Justin T. Gibbs
@ 2003-03-22 0:04 ` Jos Hulzink
0 siblings, 0 replies; 7+ messages in thread
From: Jos Hulzink @ 2003-03-22 0:04 UTC (permalink / raw)
To: Justin T. Gibbs; +Cc: Zwane Mwaikambo, Linux Kernel
On Fri, 21 Mar 2003, Justin T. Gibbs wrote:
> > Hi
> >
> > Similar issues here., though I must say the Adaptec driver hasn't worked for
> > me on all kernels I tried since my first try with 2.5.44. I get almost the
> > same output with a plain 2.5.65 kernel, though my kernel locks up just before
> > the crash you get, I get no dmesg output.
> >
> > Note that it takes ages to get trough the SCSI driver towards the lockup. I
> > guess some timeouts cause this.
>
> What kind of MB are you using? It sounds like interrupts aren't working
> for you.
Intel 440 LX chipset with MPS 1.4 enabled, onboard Adaptec controller. Can
try to disable MPS 1.4, have seen drivers using wrong irq info before.
Results will follow later.
Jos
^ permalink raw reply [flat|nested] 7+ messages in thread
end of thread, other threads:[~2003-03-21 23:53 UTC | newest]
Thread overview: 7+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2003-03-21 7:17 aic7(censored) dying horribly in 2.5.65-mm2 (fwd) Zwane Mwaikambo
2003-03-21 7:18 ` Zwane Mwaikambo
2003-03-21 7:45 ` Zwane Mwaikambo
2003-03-21 19:56 ` Justin T. Gibbs
2003-03-21 11:43 ` Jos Hulzink
2003-03-21 20:05 ` Justin T. Gibbs
2003-03-22 0:04 ` Jos Hulzink
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.