* [BUG] tg3/pci issue with recent 2.5 bk
@ 2003-04-30 15:44 James Morris
2003-04-30 15:51 ` Jeff Garzik
0 siblings, 1 reply; 4+ messages in thread
From: James Morris @ 2003-04-30 15:44 UTC (permalink / raw)
To: linux-kernel; +Cc: Jeff Garzik
Somewhere in the last few days, the tg3 driver in the 2.5 bk tree has
started failing to load (the card is Netgear GA302T), with the error
message:
"Cannot find proper PCI device base address, aborting."
This is in response to:
if (!(pci_resource_flags(pdev, 0) & IORESOURCE_MEM)) {
...
Below are lspci -vvvx outputs for the stock 2.5.68 kernel, in which the
driver loads ok, and recent (i.e. within hours) bk, which has the problem.
The difference between the two is for the PCI bridge, which is missing the
following lines in the output for the bk kernel.
Memory behind bridge: fff00000-000fffff
Prefetchable memory behind bridge: fff00000-000fffff
Any hints/suggestions/fixes appreciated.
- James
--
James Morris
<jmorris@intercode.com.au>
-------------------------------------------------------------------------
2.5.68 (ok)
-------------------------------------------------------------------------
00:00.0 Host bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX Host bridge (rev 03)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 64
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=64M]
Capabilities: [a0] AGP version 1.0
Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
00: 86 80 90 71 06 00 10 22 03 00 00 06 00 40 00 00
10: 08 00 00 e0 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 a0 00 00 00 00 00 00 00 00 00 00 00
00:01.0 PCI bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX AGP bridge (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: fff00000-000fffff
Prefetchable memory behind bridge: fff00000-000fffff
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B+
00: 86 80 91 71 07 01 20 02 03 00 04 06 00 40 01 00
10: 00 00 00 00 00 00 00 00 00 01 01 40 d0 d0 a0 22
20: f0 ff 00 00 f0 ff 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80 00
00:07.0 ISA bridge: Intel Corp. 82371AB/EB/MB PIIX4 ISA (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00: 86 80 10 71 0f 00 80 02 02 00 01 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:07.1 IDE interface: Intel Corp. 82371AB/EB/MB PIIX4 IDE (rev 01) (prog-if 80 [Master])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Region 4: I/O ports at f000 [size=16]
00: 86 80 11 71 05 00 80 02 01 80 01 01 00 40 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 f0 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:07.2 USB Controller: Intel Corp. 82371AB/EB/MB PIIX4 USB (rev 01) (prog-if 00 [UHCI])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Interrupt: pin D routed to IRQ 0
Region 4: I/O ports at e000 [size=32]
00: 86 80 12 71 05 00 80 02 01 00 03 0c 00 40 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 e0 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 ff 04 00 00
00:07.3 Bridge: Intel Corp. 82371AB/EB/MB PIIX4 ACPI (rev 02)
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin ? routed to IRQ 9
00: 86 80 13 71 03 00 80 02 02 00 80 06 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:08.0 VGA compatible controller: S3 Inc. 86c775/86c785 [Trio 64V2/DX or /GX] (rev 16) (prog-if 00 [VGA])
Subsystem: S3 Inc. 86C775 Trio64V2/DX, 86C785 Trio64V2/GX
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 16
Region 0: Memory at e4000000 (32-bit, non-prefetchable) [size=64M]
Expansion ROM at e8000000 [disabled] [size=64K]
00: 33 53 01 89 03 00 00 02 16 00 00 03 00 00 00 00
10: 00 00 00 e4 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 33 53 01 89
30: 00 00 00 e8 00 00 00 00 00 00 00 00 0b 01 00 00
00:09.0 Ethernet controller: Altima (nee BroadCom) AC1000 Gigabit Ethernet (rev 14)
Subsystem: Netgear: Unknown device 302a
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (16000ns min), cache line size 08
Interrupt: pin A routed to IRQ 17
Region 0: Memory at eb040000 (64-bit, non-prefetchable) [size=64K]
Capabilities: [40] PCI-X non-bridge device.
Command: DPERE- ERO+ RBC=0 OST=0
Status: Bus=0 Dev=0 Func=0 64bit- 133MHz- SCD- USC-, DC=simple, DMMRBC=0, DMOST=0, DMCRS=0, RSCEM-
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data
Capabilities: [58] Message Signalled Interrupts: 64bit+ Queue=0/3 Enable-
Address: 060c62ad7930231c Data: 2801
00: 3b 17 e8 03 06 00 b0 02 14 00 00 02 08 40 00 00
10: 04 00 04 eb 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 85 13 2a 30
30: 00 00 00 00 40 00 00 00 00 00 00 00 0a 01 40 00
00:0a.0 Ethernet controller: Lite-On Communications Inc LNE100TX (rev 21)
Subsystem: Netgear FA310TX
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at e400 [size=256]
Region 1: Memory at eb050000 (32-bit, non-prefetchable) [size=256]
Expansion ROM at e9000000 [disabled] [size=256K]
00: ad 11 02 00 07 00 80 02 21 00 00 02 00 40 00 00
10: 01 e4 00 00 00 00 05 eb 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 85 13 04 f0
30: 00 00 00 e9 00 00 00 00 00 00 00 00 05 01 00 00
00:0b.0 Co-processor: Hifn Inc. 7751 Security Processor (rev 01)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64, cache line size 08
Interrupt: pin A routed to IRQ 19
Region 0: Memory at eb051000 (32-bit, non-prefetchable) [size=4K]
Region 1: Memory at eb052000 (32-bit, non-prefetchable) [size=4K]
00: a3 13 05 00 06 00 80 02 01 00 40 0b 08 40 00 00
10: 00 10 05 eb 00 20 05 eb 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 09 01 00 00
00:0c.0 Ethernet controller: Intel Corp.: Unknown device 100e (rev 02)
Subsystem: Intel Corp.: Unknown device 002e
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (63750ns min), cache line size 08
Interrupt: pin A routed to IRQ 16
Region 0: Memory at eb020000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at eb000000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at e800 [size=64]
Expansion ROM at ea000000 [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [e4] PCI-X non-bridge device.
Command: DPERE- ERO+ RBC=0 OST=0
Status: Bus=0 Dev=0 Func=0 64bit- 133MHz- SCD- USC-, DC=simple, DMMRBC=0, DMOST=0, DMCRS=0, RSCEM-
Capabilities: [f0] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
00: 86 80 0e 10 07 00 30 02 02 00 00 02 08 40 00 00
10: 00 00 02 eb 00 00 00 eb 01 e8 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 86 80 2e 00
30: 00 00 00 ea dc 00 00 00 00 00 00 00 0b 01 ff 00
------------------------------------------------------------------------
bk (not ok)
------------------------------------------------------------------------
00:00.0 Host bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX Host bridge (rev 03)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 64
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=64M]
Capabilities: [a0] AGP version 1.0
Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
00: 86 80 90 71 06 00 10 22 03 00 00 06 00 40 00 00
10: 08 00 00 e0 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 a0 00 00 00 00 00 00 00 00 00 00 00
00:01.0 PCI bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX AGP bridge (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
I/O behind bridge: 0000d000-0000dfff
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B+
00: 86 80 91 71 07 01 20 02 03 00 04 06 00 40 01 00
10: 00 00 00 00 00 00 00 00 00 01 01 40 d0 d0 a0 22
20: f0 ff 00 00 f0 ff 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80 00
00:07.0 ISA bridge: Intel Corp. 82371AB/EB/MB PIIX4 ISA (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00: 86 80 10 71 0f 00 80 02 02 00 01 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:07.1 IDE interface: Intel Corp. 82371AB/EB/MB PIIX4 IDE (rev 01) (prog-if 80 [Master])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Region 4: I/O ports at f000 [size=16]
00: 86 80 11 71 05 00 80 02 01 80 01 01 00 40 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 f0 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:07.2 USB Controller: Intel Corp. 82371AB/EB/MB PIIX4 USB (rev 01) (prog-if 00 [UHCI])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Interrupt: pin D routed to IRQ 0
Region 4: I/O ports at e000 [size=32]
00: 86 80 12 71 05 00 80 02 01 00 03 0c 00 40 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 e0 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 ff 04 00 00
00:07.3 Bridge: Intel Corp. 82371AB/EB/MB PIIX4 ACPI (rev 02)
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin ? routed to IRQ 9
00: 86 80 13 71 03 00 80 02 02 00 80 06 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:08.0 VGA compatible controller: S3 Inc. 86c775/86c785 [Trio 64V2/DX or /GX] (rev 16) (prog-if 00 [VGA])
Subsystem: S3 Inc. 86C775 Trio64V2/DX, 86C785 Trio64V2/GX
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 16
Region 0: Memory at e4000000 (32-bit, non-prefetchable) [size=64M]
Expansion ROM at e8000000 [disabled] [size=64K]
00: 33 53 01 89 03 00 00 02 16 00 00 03 00 00 00 00
10: 00 00 00 e4 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 33 53 01 89
30: 00 00 00 e8 00 00 00 00 00 00 00 00 0b 01 00 00
00:09.0 Ethernet controller: Altima (nee BroadCom) AC1000 Gigabit Ethernet (rev 14)
Subsystem: Netgear: Unknown device 302a
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (16000ns min), cache line size 08
Interrupt: pin A routed to IRQ 17
Region 0: Memory at eb040000 (64-bit, non-prefetchable) [size=64K]
Capabilities: [40] PCI-X non-bridge device.
Command: DPERE- ERO+ RBC=0 OST=0
Status: Bus=0 Dev=0 Func=0 64bit- 133MHz- SCD- USC-, DC=simple, DMMRBC=0, DMOST=0, DMCRS=0, RSCEM-
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data
Capabilities: [58] Message Signalled Interrupts: 64bit+ Queue=0/3 Enable-
Address: 060c62ad7930231c Data: 2801
00: 3b 17 e8 03 06 00 b0 02 14 00 00 02 08 40 00 00
10: 04 00 04 eb 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 85 13 2a 30
30: 00 00 00 00 40 00 00 00 00 00 00 00 0a 01 40 00
00:0a.0 Ethernet controller: Lite-On Communications Inc LNE100TX (rev 21)
Subsystem: Netgear FA310TX
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at e400 [size=256]
Region 1: Memory at eb050000 (32-bit, non-prefetchable) [size=256]
Expansion ROM at e9000000 [disabled] [size=256K]
00: ad 11 02 00 07 00 80 02 21 00 00 02 00 40 00 00
10: 01 e4 00 00 00 00 05 eb 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 85 13 04 f0
30: 00 00 00 e9 00 00 00 00 00 00 00 00 05 01 00 00
00:0b.0 Co-processor: Hifn Inc. 7751 Security Processor (rev 01)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64, cache line size 08
Interrupt: pin A routed to IRQ 19
Region 0: Memory at eb051000 (32-bit, non-prefetchable) [size=4K]
Region 1: Memory at eb052000 (32-bit, non-prefetchable) [size=4K]
00: a3 13 05 00 06 00 80 02 01 00 40 0b 08 40 00 00
10: 00 10 05 eb 00 20 05 eb 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 09 01 00 00
00:0c.0 Ethernet controller: Intel Corp.: Unknown device 100e (rev 02)
Subsystem: Intel Corp.: Unknown device 002e
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (63750ns min), cache line size 08
Interrupt: pin A routed to IRQ 16
Region 0: Memory at eb020000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at eb000000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at e800 [size=64]
Expansion ROM at ea000000 [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [e4] PCI-X non-bridge device.
Command: DPERE- ERO+ RBC=0 OST=0
Status: Bus=0 Dev=0 Func=0 64bit- 133MHz- SCD- USC-, DC=simple, DMMRBC=0, DMOST=0, DMCRS=0, RSCEM-
Capabilities: [f0] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
00: 86 80 0e 10 07 00 30 02 02 00 00 02 08 40 00 00
10: 00 00 02 eb 00 00 00 eb 01 e8 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 86 80 2e 00
30: 00 00 00 ea dc 00 00 00 00 00 00 00 0b 01 ff 00
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: [BUG] tg3/pci issue with recent 2.5 bk
2003-04-30 15:44 [BUG] tg3/pci issue with recent 2.5 bk James Morris
@ 2003-04-30 15:51 ` Jeff Garzik
2003-04-30 16:32 ` James Morris
0 siblings, 1 reply; 4+ messages in thread
From: Jeff Garzik @ 2003-04-30 15:51 UTC (permalink / raw)
To: James Morris; +Cc: linux-kernel
On Thu, May 01, 2003 at 01:44:15AM +1000, James Morris wrote:
> Below are lspci -vvvx outputs for the stock 2.5.68 kernel, in which the
> driver loads ok, and recent (i.e. within hours) bk, which has the problem.
>
> The difference between the two is for the PCI bridge, which is missing the
> following lines in the output for the bk kernel.
>
> Memory behind bridge: fff00000-000fffff
> Prefetchable memory behind bridge: fff00000-000fffff
>
> Any hints/suggestions/fixes appreciated.
hmmmm. Can you look through the 2.5.68 PCI-related csets to see if
anything pops up that looks like it's messing with PCI bridge
configuration?
Jeff
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: [BUG] tg3/pci issue with recent 2.5 bk
2003-04-30 15:51 ` Jeff Garzik
@ 2003-04-30 16:32 ` James Morris
2003-05-01 1:00 ` James Morris
0 siblings, 1 reply; 4+ messages in thread
From: James Morris @ 2003-04-30 16:32 UTC (permalink / raw)
To: Jeff Garzik; +Cc: linux-kernel
On Wed, 30 Apr 2003, Jeff Garzik wrote:
> > The difference between the two is for the PCI bridge, which is missing the
> > following lines in the output for the bk kernel.
> >
> > Memory behind bridge: fff00000-000fffff
> > Prefetchable memory behind bridge: fff00000-000fffff
> >
> > Any hints/suggestions/fixes appreciated.
>
> hmmmm. Can you look through the 2.5.68 PCI-related csets to see if
> anything pops up that looks like it's messing with PCI bridge
> configuration?
Nope, can't see anything obvious.
- James
--
James Morris
<jmorris@intercode.com.au>
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: [BUG] tg3/pci issue with recent 2.5 bk
2003-04-30 16:32 ` James Morris
@ 2003-05-01 1:00 ` James Morris
0 siblings, 0 replies; 4+ messages in thread
From: James Morris @ 2003-05-01 1:00 UTC (permalink / raw)
To: Jeff Garzik; +Cc: linux-kernel
On Thu, 1 May 2003, James Morris wrote:
> > > Memory behind bridge: fff00000-000fffff
> > > Prefetchable memory behind bridge: fff00000-000fffff
> > >
> > > Any hints/suggestions/fixes appreciated.
> >
> > hmmmm. Can you look through the 2.5.68 PCI-related csets to see if
> > anything pops up that looks like it's messing with PCI bridge
> > configuration?
>
> Nope, can't see anything obvious.
It's magically fixed in the bk tree now. Thanks, whoever did that.
- James
--
James Morris
<jmorris@intercode.com.au>
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2003-05-01 0:48 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2003-04-30 15:44 [BUG] tg3/pci issue with recent 2.5 bk James Morris
2003-04-30 15:51 ` Jeff Garzik
2003-04-30 16:32 ` James Morris
2003-05-01 1:00 ` James Morris
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.