Serverworks OSB4 issues

Serverworks OSB4 issues

[Jan de Groot]

Summary: enabling DMA on the Serverworks OSB4: IDE timeouts, a bus reset
and a DMA disabled harddisk
This morning I upgraded from 2.4.20 to 2.4.21, because I needed some extra
options and someone told me the "OSB4 in impossible state"-problem when
running a CD-ROM in DMA should be fixed.After booting, the disk runs completely in PIO mode, slow as hell. With
2.4.20 it was working without problems in UDMA33 mode. I use hdparm to
turn on DMA mode (hdparm -d1 /dev/hdb). Also trying MWDMA2 doesn't help:
still IDE reset.
Kernel version:
Linux version 2.4.21 (root@server) (gcc version 2.95.4 20011002 (Debian
prerelease)) #1 SMP Tue Jun 24 08:55:05 CEST 2003
IDE initialisation logs:
SvrWks OSB4: IDE controller at PCI slot 00:0f.1
SvrWks OSB4: chipset revision 0
SvrWks OSB4: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0x2000-0x2007, BIOS settings: hda:pio, hdb:pio
    ide1: BM-DMA at 0x2008-0x200f, BIOS settings: hdc:pio, hdd:pio
hda: CD-540E, ATAPI CD/DVD-ROM drive
hdb: MAXTOR 4K040H2, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hdb: attached ide-disk driver.
hdb: host protected area => 1
hdb: 78198750 sectors (40038 MB) w/2000KiB Cache, CHS=5171/240/63
Partition check:
 hdb: hdb1 < hdb5 hdb6 >

When it goes wrong:
hda: attached ide-cdrom driver.
hda: ATAPI 40X CD-ROM drive, 128kB Cache
Uniform CD-ROM driver Revision: 3.12
hda: CHECK for good STATUS
blk: queue c02d136c, I/O limit 4095Mb (mask 0xffffffff)
hdb: dma_timer_expiry: dma status == 0x41
hdb: timeout waiting for DMA
hdb: timeout waiting for DMA
hdb: (__ide_dma_test_irq) called while not waiting
hdb: status timeout: status=0xd0 { Busy }

hdb: drive not ready for command
ide0: reset: success
hdb: DMA disabled
EXT3-fs error (device ide0(3,70)): ext3_add_entry: bad entry in directory
#196225: rec_len is smaller than minimal - offset=0, inode=4269932543,
rec_len=2, name_len=12

Re: Serverworks OSB4 issues

[Larry McVoy]

For what it is worth, I have this on bkbits.net:
    ServerWorks OSB4: IDE controller on PCI bus 00 dev 79
    ServerWorks OSB4: chipset revision 0
    ServerWorks OSB4: not 100% native mode: will probe irqs later

and I ran 2.4.21 for a day or so before chickening out and downgrading to
2.4.20.  I did not see any errors and I did run a full set of integrity
checks over all the data (BK checks, not an fsck, BK checks read and 
checksum all the data).

I did get what looked like nasty corruption under 2.5.70.
-- 
---
Larry McVoy              lm at bitmover.com          http://www.bitmover.com/lm

Re: Serverworks OSB4 issues

[Alan Cox]

What disk  and other hardware is this ? Also what gcc

Re: Serverworks OSB4 issues

[Jan de Groot]

On Fri, 2003-06-27 at 17:47, Alan Cox wrote:
> What disk  and other hardware is this ? Also what gcc
> 

Maxtor D540X 40GB (the model number should be in the logs I quoted)

It's slave to a TEAC IDE CD-ROM, which isn't used (I don't dare to put
in any CD there anymore ;))

The mainboard is an OEM Asus CUR-DLS, which came in a HP Netserver E800.
The IDE disk was bought a year or two ago with much datastorage for low
price in mind (yes, we make backups every night ;))