From: "Marco d'Itri" <md@Linux.IT>
To: linux-kernel@vger.kernel.org
Subject: irq 15: nobody cared! with KT600 chipset and 2.6.0-test9
Date: Sat, 15 Nov 2003 11:43:28 +0100 [thread overview]
Message-ID: <20031115104328.GB1897@wonderland.linux.it> (raw)
kernel: ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
kernel: ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
kernel: ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 3
kernel: ACPI: PCI Interrupt Link [LNKF] enabled at IRQ 7
kernel: ACPI: PCI Interrupt Link [LNKG] enabled at IRQ 5
kernel: ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 15
kernel: PCI: Using ACPI for IRQ routing
[...]
kernel: Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
kernel: ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
kernel: VIA8237SATA: IDE controller at PCI slot 0000:00:0f.0
kernel: VIA8237SATA: chipset revision 128
kernel: VIA8237SATA: 100%% native mode on irq 3
kernel: ide2: BM-DMA at 0xa000-0xa007, BIOS settings: hde:pio, hdf:pio
kernel: ide3: BM-DMA at 0xa008-0xa00f, BIOS settings: hdg:pio, hdh:pio
kernel: VP_IDE: IDE controller at PCI slot 0000:00:0f.1
kernel: VP_IDE: chipset revision 6
kernel: VP_IDE: not 100%% native mode: will probe irqs later
kernel: ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
kernel: VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1
kernel: ide0: BM-DMA at 0x9400-0x9407, BIOS settings: hda:DMA, hdb:DMA
kernel: ide1: BM-DMA at 0x9408-0x940f, BIOS settings: hdc:DMA, hdd:DMA
kernel: ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
kernel: hdc: IRQ probe failed (0x3cfa)
kernel: hdc: CD-ROM 50X, ATAPI CD/DVD-ROM drive
kernel: hdd: 32X10, ATAPI CD/DVD-ROM drive
kernel: irq 15: nobody cared!
kernel: Call Trace:
kernel: [<c010a92b>] __report_bad_irq+0x2b/0x90
kernel: [<c010aa24>] note_interrupt+0x64/0xa0
kernel: [<c010ac2a>] do_IRQ+0xea/0xf0
kernel: [<c01092a0>] common_interrupt+0x18/0x20
kernel: [<c011d0c4>] do_softirq+0x44/0xa0
kernel: [<c010ac11>] do_IRQ+0xd1/0xf0
kernel: [<c01092a0>] common_interrupt+0x18/0x20
kernel: [<c010aff4>] setup_irq+0x64/0xb0
kernel: [<c021a730>] ide_intr+0x0/0x130
kernel: [<c010acaf>] request_irq+0x7f/0xc0
kernel: [<c021bc86>] init_irq+0x156/0x400
kernel: [<c021a730>] ide_intr+0x0/0x130
kernel: [<c021c318>] hwif_init+0xb8/0x250
kernel: [<c021b94c>] probe_hwif_init+0x2c/0x80
kernel: [<c022761a>] ide_setup_pci_device+0x7a/0x80
kernel: [<c021902d>] via_init_one+0x3d/0x50
kernel: [<c039791d>] ide_scan_pcidev+0x5d/0x70
kernel: [<c0397976>] ide_scan_pcibus+0x46/0xd0
kernel: [<c0397823>] probe_for_hwifs+0x13/0x20
kernel: [<c0397838>] ide_init_builtin_drivers+0x8/0x20
kernel: [<c0397898>] ide_init+0x48/0x70
kernel: [<c038674b>] do_initcalls+0x2b/0xa0
kernel: [<c01278b2>] init_workqueues+0x12/0x60
kernel: [<c0105097>] init+0x27/0x110
kernel: [<c0105070>] init+0x0/0x110
kernel: [<c01072a9>] kernel_thread_helper+0x5/0xc
kernel:
kernel: handlers:
kernel: [<c021a730>] (ide_intr+0x0/0x130)
kernel: Disabling IRQ #15
kernel: ide1 at 0x170-0x177,0x376 on irq 15
Trying to mount a cdrom fails:
kernel: hdc: lost interrupt
kernel: hdc: lost interrupt
kernel: irq 15: nobody cared!
kernel: Call Trace:
kernel: [<c010a92b>] __report_bad_irq+0x2b/0x90
kernel: [<c010aa24>] note_interrupt+0x64/0xa0
kernel: [<c010ac2a>] do_IRQ+0xea/0xf0
kernel: [<c01092a0>] common_interrupt+0x18/0x20
kernel: [<c021a5af>] ide_timer_expiry+0xdf/0x1b0
kernel: [<c021a4d0>] ide_timer_expiry+0x0/0x1b0
kernel: [<c0120e90>] run_timer_softirq+0xb0/0x170
kernel: [<c011d116>] do_softirq+0x96/0xa0
kernel: [<c010ac11>] do_IRQ+0xd1/0xf0
kernel: [<c0105000>] rest_init+0x0/0x30
kernel: [<c01092a0>] common_interrupt+0x18/0x20
kernel: [<c0105000>] rest_init+0x0/0x30
kernel: [<c0107066>] default_idle+0x26/0x30
kernel: [<c01070e4>] cpu_idle+0x34/0x40
kernel: [<c03866f0>] start_kernel+0x140/0x150
kernel: [<c0386480>] unknown_bootoption+0x0/0x100
kernel:
kernel: handlers:
kernel: [<c021a730>] (ide_intr+0x0/0x130)
kernel: Disabling IRQ #15
kernel: hdc: ATAPI 50X CD-ROM drive, 128kB Cache, UDMA(33)
kernel: Uniform CD-ROM driver Revision: 3.12
kernel: hdc: lost interrupt
last message repeated 2 times
kernel: irq 15: nobody cared!
kernel: Call Trace:
kernel: [<c010a92b>] __report_bad_irq+0x2b/0x90
kernel: [<c010aa24>] note_interrupt+0x64/0xa0
kernel: [<c010ac2a>] do_IRQ+0xea/0xf0
kernel: [<c01092a0>] common_interrupt+0x18/0x20
kernel: [<c010a8b0>] handle_IRQ_event+0x20/0x70
kernel: [<c010abbc>] do_IRQ+0x7c/0xf0
kernel: [<c01092a0>] common_interrupt+0x18/0x20
kernel: [<c021a5af>] ide_timer_expiry+0xdf/0x1b0
kernel: [<c021a4d0>] ide_timer_expiry+0x0/0x1b0
kernel: [<c0120e90>] run_timer_softirq+0xb0/0x170
kernel: [<c011d116>] do_softirq+0x96/0xa0
kernel: [<c010ac11>] do_IRQ+0xd1/0xf0
kernel: [<c0105000>] rest_init+0x0/0x30
kernel: [<c01092a0>] common_interrupt+0x18/0x20
kernel: [<c0105000>] rest_init+0x0/0x30
kernel: [<c0107066>] default_idle+0x26/0x30
kernel: [<c01070e4>] cpu_idle+0x34/0x40
kernel: [<c03866f0>] start_kernel+0x140/0x150
kernel: [<c0386480>] unknown_bootoption+0x0/0x100
kernel:
kernel: handlers:
kernel: [<c021a730>] (ide_intr+0x0/0x130)
kernel: Disabling IRQ #15
[...]
And it also breaks a bit the mouse:
kernel: psmouse.c: Wheel Mouse at isa0060/serio1/input0 lost synchronization, throwing 1 bytes away.
CPU0
0: 3167529 XT-PIC timer
1: 8602 XT-PIC i8042
2: 0 XT-PIC cascade
3: 0 XT-PIC uhci_hcd, uhci_hcd
5: 0 XT-PIC ehci_hcd, VIA8233
7: 1 XT-PIC uhci_hcd, uhci_hcd
8: 5 XT-PIC rtc
9: 0 XT-PIC acpi
10: 12024 XT-PIC SysKonnect SK-98xx
11: 0 XT-PIC saa7134[0]
12: 50940 XT-PIC i8042
14: 31247 XT-PIC ide0
15: 1000005 XT-PIC ide1
NMI: 0
ERR: 0
This is an ASUS A7V600 motherboard.
00:00.0 Host bridge: VIA Technologies, Inc. VT8377 [KT400 AGP] Host Bridge (rev 80)
00:01.0 PCI bridge: VIA Technologies, Inc. VT8237 PCI Bridge
00:09.0 Ethernet controller: 3Com Corporation 3c940 1000Base? (rev 12)
00:0a.0 Multimedia controller: Philips Semiconductors SAA7134 (rev 01)
00:0f.0 RAID bus controller: VIA Technologies, Inc.: Unknown device 3149 (rev 80)
00:0f.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT8233/A/C/VT8235 PIPC Bus Master IDE (rev 06)
00:10.0 USB Controller: VIA Technologies, Inc. USB (rev 81)
00:10.1 USB Controller: VIA Technologies, Inc. USB (rev 81)
00:10.2 USB Controller: VIA Technologies, Inc. USB (rev 81)
00:10.3 USB Controller: VIA Technologies, Inc. USB (rev 81)
00:10.4 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 86)
00:10.5 Network controller: VIA Technologies, Inc.: Unknown device d104
00:11.0 ISA bridge: VIA Technologies, Inc.: Unknown device 3227
00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233/A/8235 AC97 Audio Controller (rev 60)
01:00.0 VGA compatible controller: ATI Technologies Inc: Unknown device 5964 (rev 01)
01:00.1 Display controller: ATI Technologies Inc: Unknown device 5d44 (rev 01)
--
ciao, |
Marco | [3062 cavlf5SFtruTs]
next reply other threads:[~2003-11-15 11:12 UTC|newest]
Thread overview: 18+ messages / expand[flat|nested] mbox.gz Atom feed top
2003-11-15 10:43 Marco d'Itri [this message]
2003-11-16 11:13 ` irq 15: nobody cared! with KT600 chipset and 2.6.0-test9 Marco d'Itri
-- strict thread matches above, loose matches on Subject: below --
2003-11-22 23:55 Marco d'Itri
2003-11-23 1:21 ` Linus Torvalds
2003-11-23 1:59 ` Linus Torvalds
2003-11-23 2:15 ` Marco d'Itri
2003-11-23 3:24 ` Linus Torvalds
2003-11-23 5:49 ` Len Brown
2003-11-23 11:40 ` Marco d'Itri
2003-11-23 16:40 ` Linus Torvalds
2003-11-23 18:52 ` Marco d'Itri
2003-11-23 19:12 ` Linus Torvalds
2003-11-23 19:41 ` Marco d'Itri
[not found] <UPPL.70W.11@gated-at.bofh.it>
[not found] ` <UReK.uF.5@gated-at.bofh.it>
2003-11-23 3:39 ` Andi Kleen
2003-11-23 4:23 ` Linus Torvalds
2003-11-23 5:10 ` Andi Kleen
2003-11-23 10:29 ` Marco d'Itri
2003-11-23 19:16 Brown, Len
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20031115104328.GB1897@wonderland.linux.it \
--to=md@linux.it \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.