From: Andres Meyer <andres.meyer@computer.org>
To: linux-ide@vger.kernel.org
Subject: Opteron SATA machine check exception (32bit)
Date: Wed, 10 Mar 2004 00:06:36 +0100 [thread overview]
Message-ID: <200403100006.36405.andres.meyer@computer.org> (raw)
Hi,
I am trying to get an 2x Opteron system to work. As long as I use the 80GB
Maxtor installed on the integrated IDE controller, everything works fine. As
soon as I try to use the SATA disks, I get a machine check exception and the
system reboots, with the hw clock reset to some silly date.
This one here happened within ca. 7s when trying to write some zeros
(cat /dev/zero > test.file) to the first 160GB disk. On the disk, after
reboot, there was a very small test.file.
Interesting enough, it is possible to read the disks and even do a fsck on the
fs. It is also possible to run a script that writes a small file (eg the
current time) every 5s or so for several days. As I found some strange
behaviour at on port 3&4 on the siimage controller, I did not connect these
disks for now.
Any ideas? Something I could do to help?
Andres
Serial console output:
ata1: DMA timeout
CP<U0 >0C:P UM a1c: hMianceh iChneec kC hEecxkc eEpxtcioenp:t i0on0:0
00000000000000000
04B
0
nk B4a:n kb 24:0 0b020000000000070000f007f0f
f 0
erKneerl npealn ipca:n icC:P UC PcUon tceoxntte xcto rrcuoprtr
pt u
In interrupt handler - not syncing
SW:
Linux 2.6.4-rc2 32bit
ReiserFs 3
HW:
2x Opteron 240, 3GB RAM
Tyan 2885ANRF
AMD8111: 1x Maxtor 80GB
Promise SATA 150: 4x Maxtor 4G160J8 160GB with Marvel IDE2SATA adapters
SII3114: 4x Maxtor 7Y250M0 250GB SATA
dmesg:
Feb 29 04:56:06 localhost kernel: Linux version 2.6.4-rc2 (root@dipol) (gcc
version 3.3.2 20031218 (Gentoo Linux 3.3.2-r5, propolice-3.3-7)) #3 SMP Mon
Mar 8 21:08:30 CET 2004
Feb 29 04:56:06 localhost kernel: BIOS-provided physical RAM map:
Feb 29 04:56:06 localhost kernel: BIOS-e820: 0000000000000000 -
000000000009fc00 (usable)
Feb 29 04:56:06 localhost kernel: BIOS-e820: 000000000009fc00 -
00000000000a0000 (reserved)
Feb 29 04:56:06 localhost kernel: BIOS-e820: 00000000000e0000 -
0000000000100000 (reserved)
Feb 29 04:56:06 localhost kernel: BIOS-e820: 0000000000100000 -
00000000bfff0000 (usable)
Feb 29 04:56:06 localhost kernel: BIOS-e820: 00000000bfff0000 -
00000000bffff000 (ACPI data)
Feb 29 04:56:06 localhost kernel: BIOS-e820: 00000000bffff000 -
00000000c0000000 (ACPI NVS)
Feb 29 04:56:06 localhost kernel: BIOS-e820: 00000000ff7c0000 -
0000000100000000 (reserved)
Feb 29 04:56:06 localhost kernel: 2175MB HIGHMEM available.
Feb 29 04:56:06 localhost kernel: 896MB LOWMEM available.
Feb 29 04:56:06 localhost kernel: found SMP MP-table at 000ff780
Feb 29 04:56:06 localhost kernel: On node 0 totalpages: 786416
Feb 29 04:56:06 localhost kernel: DMA zone: 4096 pages, LIFO batch:1
Feb 29 04:56:06 localhost kernel: Normal zone: 225280 pages, LIFO batch:16
Feb 29 04:56:06 localhost kernel: HighMem zone: 557040 pages, LIFO batch:16
Feb 29 04:56:06 localhost kernel: DMI 2.3 present.
Feb 29 04:56:06 localhost kernel: ACPI: RSDP (v002
ACPIAM ) @ 0x000f6740
Feb 29 04:56:06 localhost kernel: ACPI: XSDT (v001 A M I OEMXSDT 0x01000428
MSFT 0x00000097) @ 0xbfff0100
Feb 29 04:56:06 localhost kernel: ACPI: FADT (v001 A M I OEMFACP 0x01000428
MSFT 0x00000097) @ 0xbfff0281
Feb 29 04:56:06 localhost kernel: ACPI: MADT (v001 A M I OEMAPIC 0x01000428
MSFT 0x00000097) @ 0xbfff0380
Feb 29 04:56:06 localhost kernel: ACPI: OEMB (v001 A M I OEMBIOS 0x01000428
MSFT 0x00000097) @ 0xbffff040
Feb 29 04:56:06 localhost kernel: ACPI: SRAT (v001 A M I OEMSRAT 0x01000428
MSFT 0x00000097) @ 0xbfff39f0
Feb 29 04:56:06 localhost kernel: ACPI: ASF! (v001 AMIASF AMDSTRET 0x00000001
INTL 0x02002026) @ 0xbfff3ae0
Feb 29 04:56:06 localhost kernel: ACPI: DSDT (v001 0ABCF 0ABCF007 0x00000007
INTL 0x02002026) @ 0x00000000
Feb 29 04:56:06 localhost kernel: ACPI: Local APIC address 0xfee00000
Feb 29 04:56:06 localhost kernel: ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00]
enabled)
Feb 29 04:56:06 localhost kernel: Processor #0 15:5 APIC version 16
Feb 29 04:56:06 localhost kernel: ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01]
enabled)
Feb 29 04:56:06 localhost kernel: Processor #1 15:5 APIC version 16
Feb 29 04:56:06 localhost kernel: Using ACPI for processor (LAPIC)
configuration information
Feb 29 04:56:06 localhost kernel: Intel MultiProcessor Specification v1.4
Feb 29 04:56:06 localhost kernel: Virtual Wire compatibility mode.
Feb 29 04:56:06 localhost kernel: OEM ID: TYAN Product ID: S2885
APIC at: 0xFEE00000
Feb 29 04:56:06 localhost kernel: I/O APIC #2 Version 17 at 0xFEC00000.
Feb 29 04:56:06 localhost kernel: I/O APIC #3 Version 17 at 0xFF4FF000.
Feb 29 04:56:06 localhost kernel: I/O APIC #4 Version 17 at 0xFF4FE000.
Feb 29 04:56:06 localhost kernel: Enabling APIC mode: Flat. Using 3 I/O
APICs
Feb 29 04:56:06 localhost kernel: Processors: 2
Feb 29 04:56:06 localhost kernel: Built 1 zonelists
Feb 29 04:56:06 localhost kernel: Kernel command line: root=/dev/hdc5
console=tty0 console=ttyS0,9600n8
Feb 29 04:56:06 localhost kernel: Initializing CPU#0
Feb 29 04:56:06 localhost kernel: PID hash table entries: 4096 (order 12:
32768 bytes)
Feb 29 04:56:06 localhost kernel: Detected 1394.263 MHz processor.
Feb 29 04:56:06 localhost kernel: Using tsc for high-res timesource
Feb 29 04:56:06 localhost kernel: Console: colour VGA+ 80x25
Feb 29 04:56:06 localhost kernel: Memory: 3107824k/3145664k available (3092k
kernel code, 36720k reserved, 1035k data, 184k init, 2228160k highmem)
Feb 29 04:56:06 localhost kernel: Checking if this processor honours the WP
bit even in supervisor mode... Ok.
Feb 29 04:56:06 localhost kernel: Calibrating delay loop... 2736.12 BogoMIPS
Feb 29 04:56:06 localhost kernel: Dentry cache hash table entries: 524288
(order: 9, 2097152 bytes)
Feb 29 04:56:06 localhost kernel: Inode-cache hash table entries: 262144
(order: 8, 1048576 bytes)
Feb 29 04:56:06 localhost kernel: Mount-cache hash table entries: 512 (order:
0, 4096 bytes)
Feb 29 04:56:06 localhost kernel: CPU: After generic identify, caps:
078bfbff e1d3fbff 00000000 00000000
Feb 29 04:56:06 localhost kernel: CPU: After vendor identify, caps:
078bfbff e1d3fbff 00000000 00000000
Feb 29 04:56:06 localhost kernel: CPU: L1 I Cache: 64K (64 bytes/line), D
cache 64K (64 bytes/line)
Feb 29 04:56:06 localhost kernel: CPU: L2 Cache: 1024K (64 bytes/line)
Feb 29 04:56:06 localhost kernel: CPU: After all inits, caps: 078bfbf7
e1d3fbff 00000000 00000010
Feb 29 04:56:06 localhost kernel: Intel machine check architecture supported.
Feb 29 04:56:06 localhost kernel: Intel machine check reporting enabled on
CPU#0.
Feb 29 04:56:06 localhost kernel: Enabling fast FPU save and restore... done.
Feb 29 04:56:06 localhost kernel: Enabling unmasked SIMD FPU exception
support... done.
Feb 29 04:56:06 localhost kernel: Checking 'hlt' instruction... OK.
Feb 29 04:56:06 localhost kernel: POSIX conformance testing by UNIFIX
Feb 29 04:56:06 localhost kernel: CPU0: AMD Opteron(tm) Processor 240 stepping
01
Feb 29 04:56:06 localhost kernel: per-CPU timeslice cutoff: 2925.00 usecs.
Feb 29 04:56:06 localhost kernel: task migration cache decay timeout: 3 msecs.
Feb 29 04:56:06 localhost kernel: enabled ExtINT on CPU#0
Feb 29 04:56:06 localhost kernel: ESR value before enabling vector: 00000004
Feb 29 04:56:06 localhost kernel: ESR value after enabling vector: 00000000
Feb 29 04:56:06 localhost kernel: Booting processor 1/1 eip 2000
Feb 29 04:56:06 localhost kernel: Initializing CPU#1
Feb 29 04:56:06 localhost kernel: masked ExtINT on CPU#1
Feb 29 04:56:06 localhost kernel: ESR value before enabling vector: 00000000
Feb 29 04:56:06 localhost kernel: ESR value after enabling vector: 00000000
Feb 29 04:56:06 localhost kernel: Calibrating delay loop... 2785.28 BogoMIPS
Feb 29 04:56:06 localhost kernel: CPU: After generic identify, caps:
078bfbff e1d3fbff 00000000 00000000
Feb 29 04:56:06 localhost kernel: CPU: After vendor identify, caps:
078bfbff e1d3fbff 00000000 00000000
Feb 29 04:56:06 localhost kernel: CPU: L1 I Cache: 64K (64 bytes/line), D
cache 64K (64 bytes/line)
Feb 29 04:56:06 localhost kernel: CPU: L2 Cache: 1024K (64 bytes/line)
Feb 29 04:56:06 localhost kernel: CPU: After all inits, caps: 078bfbf7
e1d3fbff 00000000 00000010
Feb 29 04:56:06 localhost kernel: Intel machine check architecture supported.
Feb 29 04:56:06 localhost kernel: Intel machine check reporting enabled on
CPU#1.
Feb 29 04:56:06 localhost kernel: CPU1: AMD Opteron(tm) Processor 240 stepping
01
Feb 29 04:56:06 localhost kernel: Total of 2 processors activated (5521.40
BogoMIPS).
Feb 29 04:56:06 localhost kernel: ENABLING IO-APIC IRQs
Feb 29 04:56:06 localhost kernel: Setting 2 in the phys_id_present_map
Feb 29 04:56:06 localhost kernel: ...changing IO-APIC physical APIC ID to
2 ... ok.
Feb 29 04:56:06 localhost kernel: Setting 3 in the phys_id_present_map
Feb 29 04:56:06 localhost kernel: ...changing IO-APIC physical APIC ID to
3 ... ok.
Feb 29 04:56:06 localhost kernel: Setting 4 in the phys_id_present_map
Feb 29 04:56:06 localhost kernel: ...changing IO-APIC physical APIC ID to
4 ... ok.
Feb 29 04:56:06 localhost kernel: init IO_APIC IRQs
Feb 29 04:56:06 localhost kernel: IO-APIC (apicid-pin) 2-0, 2-9, 2-10, 2-11,
2-18, 2-20, 2-21, 2-22, 2-23, 3-1, 3-2, 3-3, 4-2, 4-3 not connected.
Feb 29 04:56:06 localhost kernel: ..TIMER: vector=0x31 pin1=2 pin2=0
Feb 29 04:56:06 localhost kernel: number of MP IRQ sources: 23.
Feb 29 04:56:06 localhost kernel: number of IO-APIC #2 registers: 24.
Feb 29 04:56:06 localhost kernel: number of IO-APIC #3 registers: 4.
Feb 29 04:56:06 localhost kernel: number of IO-APIC #4 registers: 4.
Feb 29 04:56:06 localhost kernel: testing the IO APIC.......................
Feb 29 04:56:06 localhost kernel: IO APIC #2......
Feb 29 04:56:06 localhost kernel: .... register #00: 02000000
Feb 29 04:56:06 localhost kernel: ....... : physical APIC id: 02
Feb 29 04:56:06 localhost kernel: ....... : Delivery Type: 0
Feb 29 04:56:06 localhost kernel: ....... : LTS : 0
Feb 29 04:56:06 localhost kernel: .... register #01: 00170011
Feb 29 04:56:06 localhost kernel: ....... : max redirection entries: 0017
Feb 29 04:56:06 localhost kernel: ....... : PRQ implemented: 0
Feb 29 04:56:06 localhost kernel: ....... : IO APIC version: 0011
Feb 29 04:56:06 localhost kernel: .... register #02: 02000000
Feb 29 04:56:06 localhost kernel: ....... : arbitration: 02
Feb 29 04:56:06 localhost kernel: .... IRQ redirection table:
Feb 29 04:56:06 localhost kernel: NR Log Phy Mask Trig IRR Pol Stat Dest Deli
Vect:
Feb 29 04:56:06 localhost kernel: 00 000 00 1 0 0 0 0 0 0
00
Feb 29 04:56:06 localhost kernel: 01 001 01 0 0 0 0 0 1 1
39
Feb 29 04:56:06 localhost kernel: 02 001 01 0 0 0 0 0 1 1
31
Feb 29 04:56:06 localhost kernel: 03 001 01 0 0 0 0 0 1 1
41
Feb 29 04:56:06 localhost kernel: 04 001 01 0 0 0 0 0 1 1
49
Feb 29 04:56:06 localhost kernel: 05 001 01 0 0 0 0 0 1 1
51
Feb 29 04:56:06 localhost kernel: 06 001 01 0 0 0 0 0 1 1
59
Feb 29 04:56:06 localhost kernel: 07 001 01 0 0 0 0 0 1 1
61
Feb 29 04:56:06 localhost kernel: 08 001 01 0 0 0 0 0 1 1
69
Feb 29 04:56:06 localhost kernel: 09 000 00 1 0 0 0 0 0 0
00
Feb 29 04:56:06 localhost kernel: 0a 000 00 1 0 0 0 0 0 0
00
Feb 29 04:56:06 localhost kernel: 0b 000 00 1 0 0 0 0 0 0
00
Feb 29 04:56:06 localhost kernel: 0c 001 01 0 0 0 0 0 1 1
71
Feb 29 04:56:06 localhost kernel: 0d 001 01 0 0 0 0 0 1 1
79
Feb 29 04:56:06 localhost kernel: 0e 001 01 0 0 0 0 0 1 1
81
Feb 29 04:56:06 localhost kernel: 0f 001 01 0 0 0 0 0 1 1
89
Feb 29 04:56:06 localhost kernel: 10 001 01 1 1 0 1 0 1 1
91
Feb 29 04:56:06 localhost kernel: 11 001 01 1 1 0 1 0 1 1
99
Feb 29 04:56:06 localhost kernel: 12 000 00 1 0 0 0 0 0 0
00
Feb 29 04:56:06 localhost kernel: 13 001 01 1 1 0 1 0 1 1
A1
Feb 29 04:56:06 localhost kernel: 14 000 00 1 0 0 0 0 0 0
00
Feb 29 04:56:06 localhost kernel: 15 000 00 1 0 0 0 0 0 0
00
Feb 29 04:56:06 localhost kernel: 16 000 00 1 0 0 0 0 0 0
00
Feb 29 04:56:06 localhost kernel: 17 000 00 1 0 0 0 0 0 0
00
Feb 29 04:56:06 localhost kernel: IO APIC #3......
Feb 29 04:56:06 localhost kernel: .... register #00: 03000000
Feb 29 04:56:06 localhost kernel: ....... : physical APIC id: 03
Feb 29 04:56:06 localhost kernel: ....... : Delivery Type: 0
Feb 29 04:56:06 localhost kernel: ....... : LTS : 0
Feb 29 04:56:06 localhost kernel: .... register #01: 00030011
Feb 29 04:56:06 localhost kernel: ....... : max redirection entries: 0003
Feb 29 04:56:06 localhost kernel: ....... : PRQ implemented: 0
Feb 29 04:56:06 localhost kernel: ....... : IO APIC version: 0011
Feb 29 04:56:06 localhost kernel: .... register #02: 00000000
Feb 29 04:56:06 localhost kernel: ....... : arbitration: 00
Feb 29 04:56:06 localhost kernel: .... IRQ redirection table:
Feb 29 04:56:06 localhost kernel: NR Log Phy Mask Trig IRR Pol Stat Dest Deli
Vect:
Feb 29 04:56:06 localhost kernel: 00 001 01 1 1 0 1 0 1 1
A9
Feb 29 04:56:06 localhost kernel: 01 000 00 1 0 0 0 0 0 0
00
Feb 29 04:56:06 localhost kernel: 02 000 00 1 0 0 0 0 0 0
00
Feb 29 04:56:06 localhost kernel: 03 000 00 1 0 0 0 0 0 0
00
Feb 29 04:56:06 localhost kernel: IO APIC #4......
Feb 29 04:56:06 localhost kernel: .... register #00: 04000000
Feb 29 04:56:06 localhost kernel: ....... : physical APIC id: 04
Feb 29 04:56:06 localhost kernel: ....... : Delivery Type: 0
Feb 29 04:56:06 localhost kernel: ....... : LTS : 0
Feb 29 04:56:06 localhost kernel: .... register #01: 00030011
Feb 29 04:56:06 localhost kernel: ....... : max redirection entries: 0003
Feb 29 04:56:06 localhost kernel: ....... : PRQ implemented: 0
Feb 29 04:56:06 localhost kernel: ....... : IO APIC version: 0011
Feb 29 04:56:06 localhost kernel: .... register #02: 00000000
Feb 29 04:56:06 localhost kernel: ....... : arbitration: 00
Feb 29 04:56:06 localhost kernel: .... IRQ redirection table:
Feb 29 04:56:06 localhost kernel: NR Log Phy Mask Trig IRR Pol Stat Dest Deli
Vect:
Feb 29 04:56:06 localhost kernel: 00 001 01 1 1 0 1 0 1 1
B1
Feb 29 04:56:06 localhost kernel: 01 001 01 1 1 0 1 0 1 1
B9
Feb 29 04:56:06 localhost kernel: 02 000 00 1 0 0 0 0 0 0
00
Feb 29 04:56:06 localhost kernel: 03 000 00 1 0 0 0 0 0 0
00
Feb 29 04:56:06 localhost kernel: IRQ to pin mappings:
Feb 29 04:56:06 localhost kernel: IRQ0 -> 0:2
Feb 29 04:56:06 localhost kernel: IRQ1 -> 0:1
Feb 29 04:56:06 localhost kernel: IRQ3 -> 0:3
Feb 29 04:56:06 localhost kernel: IRQ4 -> 0:4
Feb 29 04:56:06 localhost kernel: IRQ5 -> 0:5
Feb 29 04:56:06 localhost kernel: IRQ6 -> 0:6
Feb 29 04:56:06 localhost kernel: IRQ7 -> 0:7
Feb 29 04:56:06 localhost kernel: IRQ8 -> 0:8
Feb 29 04:56:06 localhost kernel: IRQ12 -> 0:12
Feb 29 04:56:06 localhost kernel: IRQ13 -> 0:13
Feb 29 04:56:06 localhost kernel: IRQ14 -> 0:14
Feb 29 04:56:06 localhost kernel: IRQ15 -> 0:15
Feb 29 04:56:06 localhost kernel: IRQ16 -> 0:16
Feb 29 04:56:06 localhost kernel: IRQ17 -> 0:17
Feb 29 04:56:06 localhost kernel: IRQ19 -> 0:19
Feb 29 04:56:06 localhost kernel: IRQ24 -> 1:0
Feb 29 04:56:06 localhost kernel: IRQ28 -> 2:0
Feb 29 04:56:06 localhost kernel: IRQ29 -> 2:1
Feb 29 04:56:06 localhost kernel: .................................... done.
Feb 29 04:56:06 localhost kernel: Using local APIC timer interrupts.
Feb 29 04:56:06 localhost kernel: calibrating APIC timer ...
Feb 29 04:56:06 localhost kernel: ..... CPU clock speed is 1393.0798 MHz.
Feb 29 04:56:06 localhost kernel: ..... host bus clock speed is 199.0114 MHz.
Feb 29 04:56:06 localhost kernel: checking TSC synchronization across 2 CPUs:
passed.
Feb 29 04:56:06 localhost kernel: Brought up 2 CPUs
Feb 29 04:56:06 localhost kernel: NET: Registered protocol family 16
Feb 29 04:56:06 localhost kernel: PCI: PCI BIOS revision 2.10 entry at
0xf0031, last bus=5
Feb 29 04:56:06 localhost kernel: PCI: Using configuration type 1
Feb 29 04:56:06 localhost kernel: SCSI subsystem initialized
Feb 29 04:56:06 localhost kernel: drivers/usb/core/usb.c: registered new
driver usbfs
Feb 29 04:56:06 localhost kernel: drivers/usb/core/usb.c: registered new
driver hub
Feb 29 04:56:06 localhost kernel: PCI: Probing PCI hardware
Feb 29 04:56:06 localhost kernel: PCI: Probing PCI hardware (bus 00)
Feb 29 04:56:06 localhost kernel: PCI: Discovered peer bus 04
Feb 29 04:56:06 localhost kernel: PCI: Using IRQ router default [1022/746b] at
0000:00:07.3
Feb 29 04:56:06 localhost kernel: PCI->APIC IRQ transform: (B0,I7,P3) -> 19
Feb 29 04:56:06 localhost kernel: PCI->APIC IRQ transform: (B0,I7,P1) -> 17
Feb 29 04:56:06 localhost kernel: PCI->APIC IRQ transform: (B1,I0,P3) -> 19
Feb 29 04:56:06 localhost kernel: PCI->APIC IRQ transform: (B1,I0,P3) -> 19
Feb 29 04:56:06 localhost kernel: PCI->APIC IRQ transform: (B1,I10,P0) -> 16
Feb 29 04:56:06 localhost kernel: PCI->APIC IRQ transform: (B1,I11,P0) -> 17
Feb 29 04:56:06 localhost kernel: PCI->APIC IRQ transform: (B1,I12,P0) -> 19
Feb 29 04:56:06 localhost kernel: PCI->APIC IRQ transform: (B2,I9,P0) -> 24
Feb 29 04:56:06 localhost kernel: PCI->APIC IRQ transform: (B3,I3,P0) -> 28
Feb 29 04:56:06 localhost kernel: PCI->APIC IRQ transform: (B3,I6,P0) -> 29
Feb 29 04:56:06 localhost kernel: PCI->APIC IRQ transform: (B5,I0,P0) -> 16
Feb 29 04:56:06 localhost kernel: Machine check exception polling timer
started.
Feb 29 04:56:06 localhost kernel: ikconfig 0.7 with /proc/config*
Feb 29 04:56:06 localhost kernel: highmem bounce pool size: 64 pages
Feb 29 04:56:06 localhost kernel: devfs: 2004-01-31 Richard Gooch
(rgooch@atnf.csiro.au)
Feb 29 04:56:06 localhost kernel: devfs: boot_options: 0x1
Feb 29 04:56:06 localhost kernel: Initializing Cryptographic API
Feb 29 04:56:06 localhost kernel: Real Time Clock Driver v1.12
Feb 29 04:56:06 localhost kernel: hw_random: AMD768 system management I/O
registers at 0x5000.
Feb 29 04:56:06 localhost kernel: hw_random hardware driver 1.0.0 loaded
Feb 29 04:56:06 localhost kernel: Linux agpgart interface v0.100 (c) Dave
Jones
Feb 29 04:56:06 localhost kernel: agpgart: Detected AMD 8151 AGP Bridge rev B2
Feb 29 04:56:06 localhost kernel: agpgart: Maximum main memory to use for agp
memory: 2925M
Feb 29 04:56:06 localhost kernel: agpgart: AGP aperture is 128M @ 0xf0000000
Feb 29 04:56:06 localhost kernel: [drm] Initialized radeon 1.9.0 20020828 on
minor 0
Feb 29 04:56:06 localhost kernel: Serial: 8250/16550 driver $Revision: 1.90 $
8 ports, IRQ sharing disabled
Feb 29 04:56:06 localhost kernel: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
Feb 29 04:56:06 localhost kernel: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
Feb 29 04:56:06 localhost kernel: RAMDISK driver initialized: 16 RAM disks of
4096K size 1024 blocksize
Feb 29 04:56:06 localhost kernel: loop: loaded (max 8 devices)
Feb 29 04:56:06 localhost kernel: Intel(R) PRO/1000 Network Driver - version
5.2.30.1-k2
Feb 29 04:56:06 localhost kernel: Copyright (c) 1999-2004 Intel Corporation.
Feb 29 04:56:06 localhost kernel: eth0: Intel(R) PRO/1000 Network Connection
Feb 29 04:56:06 localhost kernel: ns83820.c: National Semiconductor DP83820
10/100/1000 driver.
Feb 29 04:56:06 localhost kernel: tg3.c:v2.8 (February 23, 2004)
Feb 29 04:56:06 localhost kernel: eth1: Tigon3 [partno(BCM95703A30) rev 1002
PHY(5703)] (PCIX:100MHz:64-bit) 10/100/1000BaseT Ethernet 00:e0:81:27:a1:5f
Feb 29 04:56:06 localhost kernel: Universal TUN/TAP device driver 1.5 (C)
1999-2002 Maxim Krasnyansky
Feb 29 04:56:06 localhost kernel: Linux video capture interface: v1.00
Feb 29 04:56:06 localhost kernel: Uniform Multi-Platform E-IDE driver
Revision: 7.00alpha2
Feb 29 04:56:06 localhost kernel: ide: Assuming 33MHz system bus speed for PIO
modes; override with idebus=xx
Feb 29 04:56:06 localhost kernel: AMD8111: IDE controller at PCI slot
0000:00:07.1
Feb 29 04:56:06 localhost kernel: AMD8111: chipset revision 3
Feb 29 04:56:06 localhost kernel: AMD8111: not 100%% native mode: will probe
irqs later
Feb 29 04:56:06 localhost kernel: AMD8111: 0000:00:07.1 (rev 03) UDMA133
controller
Feb 29 04:56:06 localhost kernel: ide0: BM-DMA at 0xffa0-0xffa7, BIOS
settings: hda:DMA, hdb:pio
Feb 29 04:56:06 localhost kernel: ide1: BM-DMA at 0xffa8-0xffaf, BIOS
settings: hdc:DMA, hdd:pio
Feb 29 04:56:06 localhost kernel: hda: Pioneer DVD-ROM ATAPIModel DVD-120S,
ATAPI CD/DVD-ROM drive
Feb 29 04:56:06 localhost kernel: Using anticipatory io scheduler
Feb 29 04:56:06 localhost kernel: ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Feb 29 04:56:06 localhost kernel: hdc: Maxtor 4D080H4, ATA DISK drive
Feb 29 04:56:06 localhost kernel: ide1 at 0x170-0x177,0x376 on irq 15
Feb 29 04:56:06 localhost kernel: hdc: max request size: 128KiB
Feb 29 04:56:06 localhost kernel: hdc: 160086528 sectors (81964 MB) w/2048KiB
Cache, CHS=65535/16/63, UDMA(100)
Feb 29 04:56:06 localhost kernel: /dev/ide/host0/bus1/target0/lun0: p1 p2 <
p5 p6 p7 p8 p9 >
Feb 29 04:56:06 localhost kernel: hda: ATAPI 126X DVD-ROM drive, 256kB Cache,
UDMA(66)
Feb 29 04:56:06 localhost kernel: Uniform CD-ROM driver Revision: 3.20
Feb 29 04:56:06 localhost kernel: libata version 1.01 loaded.
Feb 29 04:56:06 localhost kernel: sata_promise version 0.90
Feb 29 04:56:06 localhost kernel: ata1: SATA max UDMA/133 cmd 0xF885C200 ctl
0xF885C238 bmdma 0x0 irq 29
Feb 29 04:56:06 localhost kernel: ata2: SATA max UDMA/133 cmd 0xF885C280 ctl
0xF885C2B8 bmdma 0x0 irq 29
Feb 29 04:56:06 localhost kernel: ata3: SATA max UDMA/133 cmd 0xF885C300 ctl
0xF885C338 bmdma 0x0 irq 29
Feb 29 04:56:06 localhost kernel: ata4: SATA max UDMA/133 cmd 0xF885C380 ctl
0xF885C3B8 bmdma 0x0 irq 29
Feb 29 04:56:06 localhost kernel: ata1: dev 0 cfg 49:2f00 82:7c69 83:4f09
84:4003 85:7c69 86:0e01 87:4003 88:207f
Feb 29 04:56:06 localhost kernel: ata1: dev 0 ATA, max UDMA/133, 320173056
sectors (lba48)
Feb 29 04:56:06 localhost kernel: ata1: dev 0 configured for UDMA/133
Feb 29 04:56:06 localhost kernel: scsi0 : sata_promise
Feb 29 04:56:06 localhost kernel: ata2 is slow to respond, please be patient
Feb 29 04:56:06 localhost kernel: ata2 failed to respond (30 secs)
Feb 29 04:56:06 localhost kernel: ata2: thread exiting
Feb 29 04:56:06 localhost kernel: scsi1 : sata_promise
Feb 29 04:56:06 localhost kernel: ata3: dev 0 cfg 49:2f00 82:7c69 83:4f09
84:4003 85:7c69 86:0e01 87:4003 88:207f
Feb 29 04:56:06 localhost kernel: ata3: dev 0 ATA, max UDMA/133, 320173056
sectors (lba48)
Feb 29 04:56:06 localhost kernel: ata3: dev 0 configured for UDMA/133
Feb 29 04:56:06 localhost kernel: scsi2 : sata_promise
Feb 29 04:56:06 localhost kernel: ata4: dev 0 cfg 49:2f00 82:7c69 83:4f09
84:4003 85:7c69 86:0e01 87:4003 88:207f
Feb 29 04:56:06 localhost kernel: ata4: dev 0 ATA, max UDMA/133, 320173056
sectors (lba48)
Feb 29 04:56:06 localhost kernel: ata4: dev 0 configured for UDMA/133
Feb 29 04:56:06 localhost kernel: scsi3 : sata_promise
Feb 29 04:56:06 localhost kernel: Vendor: ATA Model: Maxtor 4G160J8
Rev: 1.01
Feb 29 04:56:06 localhost kernel: Type: Direct-Access
ANSI SCSI revision: 05
Feb 29 04:56:06 localhost kernel: Vendor: ATA Model: Maxtor 4G160J8
Rev: 1.01
Feb 29 04:56:06 localhost kernel: Type: Direct-Access
ANSI SCSI revision: 05
Feb 29 04:56:06 localhost kernel: Vendor: ATA Model: Maxtor 4G160J8
Rev: 1.01
Feb 29 04:56:06 localhost kernel: Type: Direct-Access
ANSI SCSI revision: 05
Feb 29 04:56:06 localhost kernel: sata_sil version 0.53
Feb 29 04:56:06 localhost kernel: ata5: SATA max UDMA/133 cmd 0xF885EC80 ctl
0xF885EC8A bmdma 0xF885EC00 irq 17
Feb 29 04:56:06 localhost kernel: ata6: SATA max UDMA/133 cmd 0xF885ECC0 ctl
0xF885ECCA bmdma 0xF885EC08 irq 17
Feb 29 04:56:06 localhost kernel: ata7: SATA max UDMA/133 cmd 0xF885EE80 ctl
0xF885EE8A bmdma 0xF885EE00 irq 17
Feb 29 04:56:06 localhost kernel: ata8: SATA max UDMA/133 cmd 0xF885EEC0 ctl
0xF885EECA bmdma 0xF885EE08 irq 17
Feb 29 04:56:06 localhost kernel: ata5: dev 0 cfg 49:2f00 82:7c6b 83:7f09
84:4003 85:7c69 86:3e01 87:4003 88:407f
Feb 29 04:56:06 localhost kernel: ata5: dev 0 ATA, max UDMA/133, 490234752
sectors (lba48)
Feb 29 04:56:06 localhost kernel: ata5: dev 0 configured for UDMA/133
Feb 29 04:56:06 localhost kernel: scsi4 : sata_sil
Feb 29 04:56:06 localhost kernel: ata6: dev 0 cfg 49:2f00 82:7c6b 83:7f09
84:4003 85:7c69 86:3e01 87:4003 88:407f
Feb 29 04:56:06 localhost kernel: ata6: dev 0 ATA, max UDMA/133, 490234752
sectors (lba48)
Feb 29 04:56:06 localhost kernel: ata6: dev 0 configured for UDMA/133
Feb 29 04:56:06 localhost kernel: scsi5 : sata_sil
Feb 29 04:56:06 localhost kernel: ata7: no device found (phy stat 00000000)
Feb 29 04:56:06 localhost kernel: ata7: thread exiting
Feb 29 04:56:06 localhost kernel: scsi6 : sata_sil
Feb 29 04:56:06 localhost kernel: ata8: no device found (phy stat 00000000)
Feb 29 04:56:06 localhost kernel: ata8: thread exiting
Feb 29 04:56:06 localhost kernel: scsi7 : sata_sil
Feb 29 04:56:06 localhost kernel: Vendor: ATA Model: Maxtor 7Y250M0
Rev: 1.01
Feb 29 04:56:06 localhost kernel: Type: Direct-Access
ANSI SCSI revision: 05
Feb 29 04:56:06 localhost kernel: Vendor: ATA Model: Maxtor 7Y250M0
Rev: 1.01
Feb 29 04:56:06 localhost kernel: Type: Direct-Access
ANSI SCSI revision: 05
Feb 29 04:56:06 localhost kernel: SCSI device sda: 320173056 512-byte hdwr
sectors (163929 MB)
Feb 29 04:56:06 localhost kernel: SCSI device sda: drive cache: write through
Feb 29 04:56:06 localhost kernel: /dev/scsi/host0/bus0/target0/lun0: p1 < p5
>
Feb 29 04:56:06 localhost kernel: Attached scsi disk sda at scsi0, channel 0,
id 0, lun 0
Feb 29 04:56:06 localhost kernel: SCSI device sdb: 320173056 512-byte hdwr
sectors (163929 MB)
Feb 29 04:56:06 localhost kernel: SCSI device sdb: drive cache: write through
Feb 29 04:56:06 localhost kernel: /dev/scsi/host2/bus0/target0/lun0: p1 < p5
>
Feb 29 04:56:06 localhost kernel: Attached scsi disk sdb at scsi2, channel 0,
id 0, lun 0
Feb 29 04:56:06 localhost kernel: SCSI device sdc: 320173056 512-byte hdwr
sectors (163929 MB)
Feb 29 04:56:06 localhost kernel: SCSI device sdc: drive cache: write through
Feb 29 04:56:06 localhost kernel: /dev/scsi/host3/bus0/target0/lun0: p1 < p5
>
Feb 29 04:56:06 localhost kernel: Attached scsi disk sdc at scsi3, channel 0,
id 0, lun 0
Feb 29 04:56:06 localhost kernel: SCSI device sdd: 490234752 512-byte hdwr
sectors (251000 MB)
Feb 29 04:56:06 localhost kernel: SCSI device sdd: drive cache: write through
Feb 29 04:56:06 localhost kernel: /dev/scsi/host4/bus0/target0/lun0: p1 < p5
>
Feb 29 04:56:06 localhost kernel: Attached scsi disk sdd at scsi4, channel 0,
id 0, lun 0
Feb 29 04:56:06 localhost kernel: SCSI device sde: 490234752 512-byte hdwr
sectors (251000 MB)
Feb 29 04:56:06 localhost kernel: SCSI device sde: drive cache: write through
Feb 29 04:56:06 localhost kernel: /dev/scsi/host5/bus0/target0/lun0: p1 < p5
>
Feb 29 04:56:06 localhost kernel: Attached scsi disk sde at scsi5, channel 0,
id 0, lun 0
Feb 29 04:56:06 localhost kernel: Attached scsi generic sg0 at scsi0, channel
0, id 0, lun 0, type 0
Feb 29 04:56:06 localhost kernel: Attached scsi generic sg1 at scsi2, channel
0, id 0, lun 0, type 0
Feb 29 04:56:06 localhost kernel: Attached scsi generic sg2 at scsi3, channel
0, id 0, lun 0, type 0
Feb 29 04:56:06 localhost kernel: Attached scsi generic sg3 at scsi4, channel
0, id 0, lun 0, type 0
Feb 29 04:56:06 localhost kernel: Attached scsi generic sg4 at scsi5, channel
0, id 0, lun 0, type 0
Feb 29 04:56:06 localhost kernel: ohci1394: $Rev: 1172 $ Ben Collins
<bcollins@debian.org>
Feb 29 04:56:06 localhost kernel: ohci1394: fw-host0: OHCI-1394 1.1 (PCI):
IRQ=[19] MMIO=[ff0fd000-ff0fd7ff] Max Packet=[2048]
Feb 29 04:56:06 localhost kernel: video1394: Installed video1394 module
Feb 29 04:56:06 localhost kernel: ieee1394: raw1394: /dev/raw1394 device
initialized
Feb 29 04:56:06 localhost kernel: sbp2: $Rev: 1170 $ Ben Collins
<bcollins@debian.org>
Feb 29 04:56:06 localhost kernel: ieee1394: Loaded CMP driver
Feb 29 04:56:06 localhost kernel: ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host
Controller (OHCI) Driver (PCI)
Feb 29 04:56:06 localhost kernel: ohci_hcd: block sizes: ed 64 td 64
Feb 29 04:56:06 localhost kernel: ohci_hcd 0000:01:00.0: OHCI Host Controller
Feb 29 04:56:06 localhost kernel: ohci_hcd 0000:01:00.0: irq 19, pci mem
f886e000
Feb 29 04:56:06 localhost kernel: ohci_hcd 0000:01:00.0: new USB bus
registered, assigned bus number 1
Feb 29 04:56:06 localhost kernel: hub 1-0:1.0: USB hub found
Feb 29 04:56:06 localhost kernel: hub 1-0:1.0: 3 ports detected
Feb 29 04:56:06 localhost kernel: ohci_hcd 0000:01:00.1: OHCI Host Controller
Feb 29 04:56:06 localhost kernel: ohci_hcd 0000:01:00.1: irq 19, pci mem
f8870000
Feb 29 04:56:06 localhost kernel: ohci_hcd 0000:01:00.1: new USB bus
registered, assigned bus number 2
Feb 29 04:56:06 localhost kernel: hub 2-0:1.0: USB hub found
Feb 29 04:56:06 localhost kernel: hub 2-0:1.0: 3 ports detected
Feb 29 04:56:06 localhost kernel: mice: PS/2 mouse device common for all mice
Feb 29 04:56:06 localhost kernel: serio: i8042 AUX port at 0x60,0x64 irq 12
Feb 29 04:56:06 localhost kernel: serio: i8042 KBD port at 0x60,0x64 irq 1
Feb 29 04:56:06 localhost kernel: i2c /dev entries driver
Feb 29 04:56:06 localhost kernel: Advanced Linux Sound Architecture Driver
Version 1.0.2c (Thu Feb 05 15:41:49 2004 UTC).
Feb 29 04:56:06 localhost kernel: usb 2-3: new full speed USB device using
address 2
Feb 29 04:56:06 localhost kernel: ieee1394: Host added: ID:BUS[0-00:1023]
GUID[00e0810000300b5c]
Feb 29 04:56:06 localhost kernel: hub 2-3:1.0: USB hub found
Feb 29 04:56:06 localhost kernel: hub 2-3:1.0: 4 ports detected
Feb 29 04:56:06 localhost kernel: AC'97 0 analog subsections not ready
Feb 29 04:56:06 localhost kernel: intel8x0_measure_ac97_clock: measured 49028
usecs
Feb 29 04:56:06 localhost kernel: intel8x0: clocking to 48000
Feb 29 04:56:06 localhost kernel: usb 2-3.1: new full speed USB device using
address 3
Feb 29 04:56:06 localhost kernel: hub 2-3.1:1.0: USB hub found
Feb 29 04:56:06 localhost kernel: hub 2-3.1:1.0: 4 ports detected
Feb 29 04:56:06 localhost kernel: ALSA device list:
Feb 29 04:56:06 localhost kernel: #0: AMD AMD8111 at 0xa800, irq 17
Feb 29 04:56:06 localhost kernel: NET: Registered protocol family 2
Feb 29 04:56:06 localhost kernel: IP: routing cache hash table of 16384
buckets, 256Kbytes
Feb 29 04:56:06 localhost kernel: usb 2-3.3: new full speed USB device using
address 4
Feb 29 04:56:06 localhost kernel: hub 2-3.3:1.0: USB hub found
Feb 29 04:56:06 localhost kernel: hub 2-3.3:1.0: 4 ports detected
Feb 29 04:56:06 localhost kernel: TCP: Hash tables configured (established
262144 bind 43690)
Feb 29 04:56:06 localhost kernel: IPv4 over IPv4 tunneling driver
Feb 29 04:56:06 localhost kernel: NET: Registered protocol family 1
Feb 29 04:56:06 localhost kernel: NET: Registered protocol family 10
Feb 29 04:56:06 localhost kernel: IPv6 over IPv4 tunneling driver
Feb 29 04:56:06 localhost kernel: NET: Registered protocol family 17
Feb 29 04:56:06 localhost kernel: NET: Registered protocol family 15
Feb 29 04:56:06 localhost kernel: found reiserfs format "3.6" with standard
journal
Feb 29 04:56:06 localhost kernel: usb 2-3.3.1: new low speed USB device using
address 5
Feb 29 04:56:06 localhost kernel: usb 2-3.3.3: new low speed USB device using
address 6
Feb 29 04:56:06 localhost kernel: usb 2-3.1.1: new full speed USB device using
address 7
Feb 29 04:56:06 localhost kernel: usb 2-3.1.3: new low speed USB device using
address 8
Feb 29 04:56:06 localhost kernel: usb 2-3.1.4: new low speed USB device using
address 9
Feb 29 04:56:06 localhost kernel: Reiserfs journal params: device hdc5, size
8192, journal first block 18, max trans len 1024, max batch 900, max commit
age 30, max trans age 30
Feb 29 04:56:06 localhost kernel: reiserfs: checking transaction log (hdc5)
for (hdc5)
Feb 29 04:56:06 localhost kernel: reiserfs: replayed 27 transactions in 0
seconds
Feb 29 04:56:06 localhost kernel: Using r5 hash to sort names
Feb 29 04:56:06 localhost kernel: VFS: Mounted root (reiserfs filesystem)
readonly.
Feb 29 04:56:06 localhost kernel: Mounted devfs on /dev
Feb 29 04:56:06 localhost kernel: Freeing unused kernel memory: 184k freed
Feb 29 04:56:06 localhost kernel: Adding 1004020k swap on /dev/hdc8.
Priority:-1 extents:1
Feb 29 04:56:06 localhost kernel: Removing [665669 3328884 0x0 SD]..done
Feb 29 04:56:06 localhost kernel: There were 1 uncompleted unlinks/truncates.
Completed
Feb 29 04:56:06 localhost kernel: bttv: driver version 0.9.12 loaded
Feb 29 04:56:06 localhost kernel: bttv: using 8 buffers with 2080k (520 pages)
each for capture
Feb 29 04:56:06 localhost kernel: bttv: Bt8xx card found (0).
Feb 29 04:56:06 localhost kernel: bttv0: Bt848 (rev 17) at 0000:01:0a.0, irq:
16, latency: 64, mmio: 0xde6ff000
Feb 29 04:56:06 localhost kernel: bttv0: using: Hauppauge (bt848)
[card=2,insmod option]
Feb 29 04:56:06 localhost kernel: bttv0: gpio: en=00000000, out=00000000
in=00fffffb [init]
Feb 29 04:56:06 localhost kernel: bttv0: Hauppauge/Voodoo msp34xx: reset line
init [5]
Feb 29 04:56:06 localhost kernel: msp34xx: setvolume: mute=on 65535:65535
v=0x00 b=0x00
Feb 29 04:56:06 localhost kernel: msp34xx: init: chip=MSP3400C-C6
Feb 29 04:56:06 localhost kernel: msp3400: daemon started
Feb 29 04:56:06 localhost kernel: msp3400: thread: sleep
Feb 29 04:56:06 localhost kernel: tuner: chip found at addr 0xc2 i2c-bus bt848
#0 [sw]
Feb 29 04:56:06 localhost kernel: tuner: type set to 1 (Philips PAL_I (FI1246
and compatibles)) by insmod option
Feb 29 04:56:06 localhost kernel: bttv0: Hauppauge eeprom: model=60324,
tuner=Philips FM1216 (5), radio=yes
Feb 29 04:56:06 localhost kernel: bttv0: using tuner=5
Feb 29 04:56:06 localhost kernel: tuner: type already set to 1, ignoring
request for 5
Feb 29 04:56:06 localhost kernel: bttv0: i2c: checking for MSP34xx @ 0x80...
found
Feb 29 04:56:06 localhost kernel: bttv0: i2c: checking for TDA9875 @ 0xb0...
not found
Feb 29 04:56:06 localhost kernel: bttv0: i2c: checking for TDA7432 @ 0x8a...
not found
Feb 29 04:56:06 localhost kernel: tvaudio: TV audio decoder + audio/video mux
driver
Feb 29 04:56:06 localhost kernel: tvaudio: known chips:
tda9840,tda9873h,tda9874h/a,tda9850,tda9855,tea6300,tea6420,tda8425,pic16c54
(PV951),ta8874z
Feb 29 04:56:06 localhost kernel: bttv0: registered device video0
Feb 29 04:56:06 localhost kernel: bttv0: registered device vbi0
Feb 29 04:56:06 localhost kernel: bttv0: registered device radio0
Feb 29 04:56:06 localhost kernel: msp34xx: AUDC_SET_INPUT(4)
Feb 29 04:56:06 localhost kernel: msp34xx: AUDC_SET_INPUT(4)
Feb 29 04:56:06 localhost kernel: found reiserfs format "3.6" with standard
journal
Feb 29 04:56:06 localhost kernel: Reiserfs journal params: device hdc9, size
8192, journal first block 18, max trans len 1024, max batch 900, max commit
age 30, max trans age 30
Feb 29 04:56:06 localhost kernel: reiserfs: checking transaction log (hdc9)
for (hdc9)
Feb 29 04:56:06 localhost kernel: reiserfs: replayed 1 transactions in 0
seconds
Feb 29 04:56:06 localhost kernel: Using r5 hash to sort names
Feb 29 04:56:06 localhost kernel: found reiserfs format "3.6" with standard
journal
Feb 29 04:56:06 localhost kernel: Reiserfs journal params: device sda5, size
8192, journal first block 18, max trans len 1024, max batch 900, max commit
age 30, max trans age 30
Feb 29 04:56:06 localhost kernel: reiserfs: checking transaction log (sda5)
for (sda5)
Feb 29 04:56:06 localhost kernel: Using r5 hash to sort names
Feb 29 04:56:06 localhost kernel: found reiserfs format "3.6" with standard
journal
Feb 29 04:56:06 localhost kernel: Reiserfs journal params: device sdb5, size
8192, journal first block 18, max trans len 1024, max batch 900, max commit
age 30, max trans age 30
Feb 29 04:56:06 localhost kernel: reiserfs: checking transaction log (sdb5)
for (sdb5)
Feb 29 04:56:06 localhost kernel: Using r5 hash to sort names
Feb 29 04:56:06 localhost kernel: found reiserfs format "3.6" with standard
journal
Feb 29 04:56:06 localhost kernel: Reiserfs journal params: device sde5, size
8192, journal first block 18, max trans len 1024, max batch 900, max commit
age 30, max trans age 30
Feb 29 04:56:06 localhost kernel: reiserfs: checking transaction log (sde5)
for (sde5)
Feb 29 04:56:06 localhost kernel: Using r5 hash to sort names
Feb 29 04:56:06 localhost kernel: devfs_mk_dev: could not append to parent for
vcc/1
Feb 29 04:56:06 localhost kernel: devfs_mk_dev: could not append to parent for
vcc/a1
Feb 29 04:56:06 localhost kernel: Disabled Privacy Extensions on device
c04b95c0(lo)
Feb 29 04:56:06 localhost kernel: e1000: eth0 NIC Link is Up 100 Mbps Full
Duplex
.config:
#
# Automatically generated make config: don't edit
#
CONFIG_X86=y
CONFIG_MMU=y
CONFIG_UID16=y
CONFIG_GENERIC_ISA_DMA=y
#
# Code maturity level options
#
CONFIG_EXPERIMENTAL=y
CONFIG_BROKEN=y
CONFIG_BROKEN_ON_SMP=y
#
# General setup
#
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
CONFIG_SYSCTL=y
CONFIG_LOG_BUF_SHIFT=15
CONFIG_HOTPLUG=y
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
CONFIG_KALLSYMS=y
CONFIG_FUTEX=y
CONFIG_EPOLL=y
CONFIG_IOSCHED_NOOP=y
CONFIG_IOSCHED_AS=y
CONFIG_IOSCHED_DEADLINE=y
#
# Loadable module support
#
CONFIG_MODULES=y
CONFIG_OBSOLETE_MODPARM=y
CONFIG_KMOD=y
#
# Processor type and features
#
CONFIG_X86_PC=y
CONFIG_MK8=y
CONFIG_X86_CMPXCHG=y
CONFIG_X86_XADD=y
CONFIG_X86_L1_CACHE_SHIFT=6
CONFIG_RWSEM_XCHGADD_ALGORITHM=y
CONFIG_X86_WP_WORKS_OK=y
CONFIG_X86_INVLPG=y
CONFIG_X86_BSWAP=y
CONFIG_X86_POPAD_OK=y
CONFIG_X86_GOOD_APIC=y
CONFIG_X86_INTEL_USERCOPY=y
CONFIG_X86_USE_PPRO_CHECKSUM=y
CONFIG_HPET_TIMER=y
CONFIG_HPET_EMULATE_RTC=y
CONFIG_SMP=y
CONFIG_NR_CPUS=8
CONFIG_X86_LOCAL_APIC=y
CONFIG_X86_IO_APIC=y
CONFIG_X86_TSC=y
CONFIG_X86_MCE=y
CONFIG_X86_MCE_NONFATAL=y
CONFIG_HIGHMEM4G=y
CONFIG_HIGHMEM=y
CONFIG_HAVE_DEC_LOCK=y
#
# Power management options (ACPI, APM)
#
#
# ACPI (Advanced Configuration and Power Interface) Support
#
CONFIG_ACPI_BOOT=y
#
# CPU Frequency scaling
#
#
# Bus options (PCI, PCMCIA, EISA, MCA, ISA)
#
CONFIG_PCI=y
CONFIG_PCI_GOANY=y
CONFIG_PCI_BIOS=y
CONFIG_PCI_DIRECT=y
CONFIG_PCI_NAMES=y
#
# PCMCIA/CardBus support
#
#
# PCI Hotplug Support
#
#
# Executable file formats
#
CONFIG_BINFMT_ELF=y
#
# Device Drivers
#
#
# Generic Driver Options
#
#
# Memory Technology Devices (MTD)
#
#
# Parallel port support
#
#
# Plug and Play support
#
#
# Block devices
#
CONFIG_BLK_DEV_LOOP=y
CONFIG_BLK_DEV_CRYPTOLOOP=m
CONFIG_BLK_DEV_NBD=m
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_SIZE=4096
CONFIG_BLK_DEV_INITRD=y
CONFIG_LBD=y
#
# ATA/ATAPI/MFM/RLL support
#
CONFIG_IDE=y
CONFIG_BLK_DEV_IDE=y
#
# Please see Documentation/ide.txt for help/info on IDE drives
#
CONFIG_BLK_DEV_IDEDISK=y
CONFIG_IDEDISK_MULTI_MODE=y
CONFIG_BLK_DEV_IDECD=y
#
# IDE chipset support/bugfixes
#
CONFIG_IDE_GENERIC=y
CONFIG_BLK_DEV_IDEPCI=y
CONFIG_IDEPCI_SHARE_IRQ=y
CONFIG_BLK_DEV_GENERIC=y
CONFIG_BLK_DEV_IDEDMA_PCI=y
CONFIG_IDEDMA_PCI_AUTO=y
CONFIG_BLK_DEV_ADMA=y
CONFIG_BLK_DEV_AMD74XX=y
CONFIG_BLK_DEV_SIIMAGE=y
CONFIG_BLK_DEV_IDEDMA=y
CONFIG_IDEDMA_AUTO=y
#
# SCSI device support
#
CONFIG_SCSI=y
CONFIG_SCSI_PROC_FS=y
#
# SCSI support type (disk, tape, CD-ROM)
#
CONFIG_BLK_DEV_SD=y
CONFIG_BLK_DEV_SR=y
CONFIG_BLK_DEV_SR_VENDOR=y
CONFIG_CHR_DEV_SG=y
#
# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
#
CONFIG_SCSI_MULTI_LUN=y
CONFIG_SCSI_REPORT_LUNS=y
CONFIG_SCSI_CONSTANTS=y
#
# SCSI low-level drivers
#
CONFIG_SCSI_SATA=y
CONFIG_SCSI_SATA_PROMISE=y
CONFIG_SCSI_SATA_SIL=y
CONFIG_SCSI_QLA2XXX=y
#
# Multi-device support (RAID and LVM)
#
#
# Fusion MPT device support
#
#
# IEEE 1394 (FireWire) support
#
CONFIG_IEEE1394=y
#
# Subsystem Options
#
#
# Device Drivers
#
CONFIG_IEEE1394_OHCI1394=y
#
# Protocol Drivers
#
CONFIG_IEEE1394_VIDEO1394=y
CONFIG_IEEE1394_SBP2=y
CONFIG_IEEE1394_DV1394=y
CONFIG_IEEE1394_RAWIO=y
CONFIG_IEEE1394_CMP=y
#
# I2O device support
#
#
# Macintosh device drivers
#
#
# Networking support
#
CONFIG_NET=y
#
# Networking options
#
CONFIG_PACKET=y
CONFIG_NETLINK_DEV=y
CONFIG_UNIX=y
CONFIG_NET_KEY=y
CONFIG_INET=y
CONFIG_IP_MULTICAST=y
CONFIG_IP_ADVANCED_ROUTER=y
CONFIG_IP_MULTIPLE_TABLES=y
CONFIG_IP_ROUTE_FWMARK=y
CONFIG_IP_ROUTE_NAT=y
CONFIG_IP_ROUTE_MULTIPATH=y
CONFIG_IP_ROUTE_TOS=y
CONFIG_IP_ROUTE_VERBOSE=y
CONFIG_NET_IPIP=y
CONFIG_NET_IPGRE=m
CONFIG_NET_IPGRE_BROADCAST=y
CONFIG_IP_MROUTE=y
CONFIG_IP_PIMSM_V1=y
CONFIG_IP_PIMSM_V2=y
CONFIG_ARPD=y
CONFIG_INET_ECN=y
CONFIG_SYN_COOKIES=y
CONFIG_INET_AH=m
CONFIG_INET_ESP=m
CONFIG_INET_IPCOMP=m
#
# IP: Virtual Server Configuration
#
CONFIG_IP_VS=m
CONFIG_IP_VS_TAB_BITS=12
#
# IPVS transport protocol load balancing support
#
CONFIG_IP_VS_PROTO_TCP=y
CONFIG_IP_VS_PROTO_UDP=y
CONFIG_IP_VS_PROTO_ESP=y
CONFIG_IP_VS_PROTO_AH=y
#
# IPVS scheduler
#
CONFIG_IP_VS_RR=m
CONFIG_IP_VS_WRR=m
CONFIG_IP_VS_LC=m
CONFIG_IP_VS_WLC=m
CONFIG_IP_VS_LBLC=m
CONFIG_IP_VS_LBLCR=m
CONFIG_IP_VS_DH=m
CONFIG_IP_VS_SH=m
CONFIG_IP_VS_SED=m
CONFIG_IP_VS_NQ=m
#
# IPVS application helper
#
CONFIG_IP_VS_FTP=m
CONFIG_IPV6=y
CONFIG_IPV6_PRIVACY=y
CONFIG_INET6_AH=m
CONFIG_INET6_ESP=m
CONFIG_INET6_IPCOMP=m
CONFIG_IPV6_TUNNEL=m
CONFIG_BRIDGE=m
CONFIG_NETFILTER=y
CONFIG_BRIDGE_NETFILTER=y
#
# IP: Netfilter Configuration
#
CONFIG_IP_NF_CONNTRACK=m
CONFIG_IP_NF_FTP=m
CONFIG_IP_NF_IRC=m
CONFIG_IP_NF_TFTP=m
CONFIG_IP_NF_AMANDA=m
CONFIG_IP_NF_QUEUE=m
CONFIG_IP_NF_IPTABLES=m
CONFIG_IP_NF_MATCH_LIMIT=m
CONFIG_IP_NF_MATCH_IPRANGE=m
CONFIG_IP_NF_MATCH_MAC=m
CONFIG_IP_NF_MATCH_PKTTYPE=m
CONFIG_IP_NF_MATCH_MARK=m
CONFIG_IP_NF_MATCH_MULTIPORT=m
CONFIG_IP_NF_MATCH_TOS=m
CONFIG_IP_NF_MATCH_RECENT=m
CONFIG_IP_NF_MATCH_ECN=m
CONFIG_IP_NF_MATCH_DSCP=m
CONFIG_IP_NF_MATCH_AH_ESP=m
CONFIG_IP_NF_MATCH_LENGTH=m
CONFIG_IP_NF_MATCH_TTL=m
CONFIG_IP_NF_MATCH_TCPMSS=m
CONFIG_IP_NF_MATCH_HELPER=m
CONFIG_IP_NF_MATCH_STATE=m
CONFIG_IP_NF_MATCH_CONNTRACK=m
CONFIG_IP_NF_MATCH_OWNER=m
CONFIG_IP_NF_MATCH_PHYSDEV=m
CONFIG_IP_NF_FILTER=m
CONFIG_IP_NF_TARGET_REJECT=m
CONFIG_IP_NF_NAT=m
CONFIG_IP_NF_NAT_NEEDED=y
CONFIG_IP_NF_TARGET_MASQUERADE=m
CONFIG_IP_NF_TARGET_REDIRECT=m
CONFIG_IP_NF_TARGET_NETMAP=m
CONFIG_IP_NF_TARGET_SAME=m
CONFIG_IP_NF_NAT_SNMP_BASIC=m
CONFIG_IP_NF_NAT_IRC=m
CONFIG_IP_NF_NAT_FTP=m
CONFIG_IP_NF_NAT_TFTP=m
CONFIG_IP_NF_NAT_AMANDA=m
CONFIG_IP_NF_MANGLE=m
CONFIG_IP_NF_TARGET_TOS=m
CONFIG_IP_NF_TARGET_ECN=m
CONFIG_IP_NF_TARGET_DSCP=m
CONFIG_IP_NF_TARGET_MARK=m
CONFIG_IP_NF_TARGET_CLASSIFY=m
CONFIG_IP_NF_TARGET_LOG=m
CONFIG_IP_NF_TARGET_ULOG=m
CONFIG_IP_NF_TARGET_TCPMSS=m
CONFIG_IP_NF_ARPTABLES=m
CONFIG_IP_NF_ARPFILTER=m
CONFIG_IP_NF_ARP_MANGLE=m
#
# IPv6: Netfilter Configuration
#
CONFIG_IP6_NF_QUEUE=m
CONFIG_IP6_NF_IPTABLES=m
CONFIG_IP6_NF_MATCH_LIMIT=m
CONFIG_IP6_NF_MATCH_MAC=m
CONFIG_IP6_NF_MATCH_RT=m
CONFIG_IP6_NF_MATCH_OPTS=m
CONFIG_IP6_NF_MATCH_FRAG=m
CONFIG_IP6_NF_MATCH_HL=m
CONFIG_IP6_NF_MATCH_MULTIPORT=m
CONFIG_IP6_NF_MATCH_OWNER=m
CONFIG_IP6_NF_MATCH_MARK=m
CONFIG_IP6_NF_MATCH_IPV6HEADER=m
CONFIG_IP6_NF_MATCH_AHESP=m
CONFIG_IP6_NF_MATCH_LENGTH=m
CONFIG_IP6_NF_MATCH_EUI64=m
CONFIG_IP6_NF_FILTER=m
CONFIG_IP6_NF_TARGET_LOG=m
CONFIG_IP6_NF_MANGLE=m
CONFIG_IP6_NF_TARGET_MARK=m
#
# Bridge: Netfilter Configuration
#
CONFIG_BRIDGE_NF_EBTABLES=m
CONFIG_BRIDGE_EBT_BROUTE=m
CONFIG_BRIDGE_EBT_T_FILTER=m
CONFIG_BRIDGE_EBT_T_NAT=m
CONFIG_BRIDGE_EBT_802_3=m
CONFIG_BRIDGE_EBT_AMONG=m
CONFIG_BRIDGE_EBT_ARP=m
CONFIG_BRIDGE_EBT_IP=m
CONFIG_BRIDGE_EBT_LIMIT=m
CONFIG_BRIDGE_EBT_MARK=m
CONFIG_BRIDGE_EBT_PKTTYPE=m
CONFIG_BRIDGE_EBT_STP=m
CONFIG_BRIDGE_EBT_VLAN=m
CONFIG_BRIDGE_EBT_ARPREPLY=m
CONFIG_BRIDGE_EBT_DNAT=m
CONFIG_BRIDGE_EBT_MARK_T=m
CONFIG_BRIDGE_EBT_REDIRECT=m
CONFIG_BRIDGE_EBT_SNAT=m
CONFIG_BRIDGE_EBT_LOG=m
CONFIG_XFRM=y
CONFIG_XFRM_USER=m
#
# SCTP Configuration (EXPERIMENTAL)
#
CONFIG_IPV6_SCTP__=y
CONFIG_IP_SCTP=m
CONFIG_SCTP_DBG_MSG=y
CONFIG_SCTP_DBG_OBJCNT=y
CONFIG_SCTP_HMAC_MD5=y
#
# QoS and/or fair queueing
#
CONFIG_NET_SCHED=y
CONFIG_NET_SCH_CBQ=y
CONFIG_NET_SCH_HTB=y
CONFIG_NET_SCH_HFSC=y
CONFIG_NET_SCH_CSZ=y
CONFIG_NET_SCH_PRIO=y
CONFIG_NET_SCH_RED=y
CONFIG_NET_SCH_SFQ=y
CONFIG_NET_SCH_TEQL=y
CONFIG_NET_SCH_TBF=y
CONFIG_NET_SCH_GRED=y
CONFIG_NET_SCH_DSMARK=y
CONFIG_NET_SCH_INGRESS=m
CONFIG_NET_QOS=y
CONFIG_NET_ESTIMATOR=y
CONFIG_NET_CLS=y
CONFIG_NET_CLS_TCINDEX=y
CONFIG_NET_CLS_ROUTE4=y
CONFIG_NET_CLS_ROUTE=y
CONFIG_NET_CLS_FW=y
CONFIG_NET_CLS_U32=y
CONFIG_NET_CLS_RSVP=y
CONFIG_NET_CLS_RSVP6=y
CONFIG_NET_CLS_POLICE=y
#
# Network testing
#
CONFIG_NETDEVICES=y
#
# ARCnet devices
#
CONFIG_TUN=y
#
# Ethernet (10 or 100Mbit)
#
#
# Ethernet (1000 Mbit)
#
CONFIG_E1000=y
CONFIG_NS83820=y
CONFIG_TIGON3=y
#
# Ethernet (10000 Mbit)
#
#
# Wireless LAN (non-hamradio)
#
#
# Token Ring devices
#
#
# Wan interfaces
#
#
# Amateur Radio support
#
#
# IrDA (infrared) support
#
#
# Bluetooth support
#
CONFIG_BT=m
CONFIG_BT_L2CAP=m
CONFIG_BT_SCO=m
CONFIG_BT_RFCOMM=m
CONFIG_BT_RFCOMM_TTY=y
CONFIG_BT_BNEP=m
CONFIG_BT_BNEP_MC_FILTER=y
CONFIG_BT_BNEP_PROTO_FILTER=y
#
# Bluetooth device drivers
#
CONFIG_BT_HCIUSB=m
#
# ISDN subsystem
#
#
# Telephony Support
#
#
# Input device support
#
CONFIG_INPUT=y
#
# Userland interfaces
#
CONFIG_INPUT_MOUSEDEV=y
CONFIG_INPUT_MOUSEDEV_PSAUX=y
CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
CONFIG_INPUT_JOYDEV=y
CONFIG_INPUT_EVDEV=y
#
# Input I/O drivers
#
CONFIG_SOUND_GAMEPORT=y
CONFIG_SERIO=y
CONFIG_SERIO_I8042=y
#
# Input Device Drivers
#
CONFIG_INPUT_KEYBOARD=y
CONFIG_KEYBOARD_ATKBD=y
CONFIG_INPUT_MOUSE=y
CONFIG_MOUSE_PS2=y
CONFIG_INPUT_JOYSTICK=y
CONFIG_JOYSTICK_IFORCE=m
CONFIG_JOYSTICK_IFORCE_USB=y
CONFIG_JOYSTICK_WARRIOR=m
CONFIG_JOYSTICK_MAGELLAN=m
CONFIG_INPUT_MISC=y
#
# Character devices
#
CONFIG_VT=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
#
# Serial drivers
#
CONFIG_SERIAL_8250=y
CONFIG_SERIAL_8250_CONSOLE=y
CONFIG_SERIAL_8250_NR_UARTS=4
#
# Non-8250 serial port support
#
CONFIG_SERIAL_CORE=y
CONFIG_SERIAL_CORE_CONSOLE=y
CONFIG_UNIX98_PTYS=y
CONFIG_LEGACY_PTYS=y
CONFIG_LEGACY_PTY_COUNT=256
#
# Mice
#
#
# IPMI
#
CONFIG_IPMI_HANDLER=m
CONFIG_IPMI_DEVICE_INTERFACE=m
CONFIG_IPMI_KCS=m
#
# Watchdog Cards
#
CONFIG_HW_RANDOM=y
CONFIG_RTC=y
#
# Ftape, the floppy tape device driver
#
CONFIG_AGP=y
CONFIG_AGP_AMD64=y
CONFIG_DRM=y
CONFIG_DRM_RADEON=y
#
# I2C support
#
CONFIG_I2C=y
CONFIG_I2C_CHARDEV=y
#
# I2C Algorithms
#
CONFIG_I2C_ALGOBIT=y
CONFIG_I2C_ALGOPCF=y
#
# I2C Hardware Bus support
#
CONFIG_I2C_AMD8111=y
CONFIG_I2C_ISA=y
#
# I2C Hardware Sensors Chip support
#
CONFIG_I2C_SENSOR=m
CONFIG_SENSORS_ADM1021=m
CONFIG_SENSORS_ASB100=m
CONFIG_SENSORS_EEPROM=m
CONFIG_SENSORS_FSCHER=m
CONFIG_SENSORS_GL518SM=m
CONFIG_SENSORS_IT87=m
CONFIG_SENSORS_LM75=m
CONFIG_SENSORS_LM78=m
CONFIG_SENSORS_LM83=m
CONFIG_SENSORS_LM85=m
CONFIG_SENSORS_LM90=m
CONFIG_SENSORS_VIA686A=m
CONFIG_SENSORS_W83781D=m
CONFIG_SENSORS_W83L785TS=m
#
# Misc devices
#
#
# Multimedia devices
#
CONFIG_VIDEO_DEV=y
#
# Video For Linux
#
#
# Video Adapters
#
CONFIG_VIDEO_BT848=m
#
# Radio Adapters
#
#
# Digital Video Broadcasting Devices
#
CONFIG_VIDEO_TUNER=m
CONFIG_VIDEO_BUF=m
CONFIG_VIDEO_BTCX=m
CONFIG_VIDEO_IR=m
#
# Graphics support
#
#
# Console display driver support
#
CONFIG_VGA_CONSOLE=y
CONFIG_DUMMY_CONSOLE=y
#
# Sound
#
CONFIG_SOUND=y
#
# Advanced Linux Sound Architecture
#
CONFIG_SND=y
CONFIG_SND_OSSEMUL=y
CONFIG_SND_MIXER_OSS=y
CONFIG_SND_PCM_OSS=y
CONFIG_SND_RTCTIMER=y
#
# Generic devices
#
#
# PCI devices
#
CONFIG_SND_BT87X=m
CONFIG_SND_EMU10K1=y
CONFIG_SND_INTEL8X0=y
#
# ALSA USB devices
#
CONFIG_SND_USB_AUDIO=m
#
# Open Sound System
#
CONFIG_SOUND_PRIME=m
CONFIG_SOUND_BT878=m
CONFIG_SOUND_TVMIXER=m
#
# USB support
#
CONFIG_USB=y
#
# Miscellaneous USB options
#
CONFIG_USB_DEVICEFS=y
#
# USB Host Controller Drivers
#
CONFIG_USB_OHCI_HCD=y
#
# USB Device Class drivers
#
CONFIG_USB_AUDIO=m
#
# USB Bluetooth TTY can only be used with disabled Bluetooth subsystem
#
CONFIG_USB_PRINTER=m
CONFIG_USB_STORAGE=m
#
# USB Human Interface Devices (HID)
#
CONFIG_USB_HID=m
CONFIG_USB_HIDINPUT=y
CONFIG_HID_FF=y
CONFIG_HID_PID=y
CONFIG_LOGITECH_FF=y
CONFIG_THRUSTMASTER_FF=y
CONFIG_USB_HIDDEV=y
#
# USB HID Boot Protocol drivers
#
#
# USB Imaging devices
#
#
# USB Multimedia devices
#
CONFIG_USB_PWC=m
#
# USB Network adaptors
#
CONFIG_USB_USBNET=m
#
# USB Host-to-Host Cables
#
CONFIG_USB_AN2720=y
CONFIG_USB_BELKIN=y
CONFIG_USB_GENESYS=y
CONFIG_USB_NET1080=y
CONFIG_USB_PL2301=y
#
# Intelligent USB Devices/Gadgets
#
CONFIG_USB_ARMLINUX=y
CONFIG_USB_EPSON2888=y
CONFIG_USB_ZAURUS=y
CONFIG_USB_CDCETHER=y
#
# USB Network Adapters
#
#
# USB port drivers
#
#
# USB Serial Converter support
#
#
# USB Miscellaneous drivers
#
#
# USB Gadget Support
#
CONFIG_USB_GADGET=m
CONFIG_USB_GADGET_NET2280=y
CONFIG_USB_NET2280=m
#
# File systems
#
CONFIG_EXT2_FS=y
CONFIG_EXT2_FS_XATTR=y
CONFIG_EXT2_FS_POSIX_ACL=y
CONFIG_EXT3_FS=y
CONFIG_EXT3_FS_XATTR=y
CONFIG_EXT3_FS_POSIX_ACL=y
CONFIG_JBD=y
CONFIG_FS_MBCACHE=y
CONFIG_REISERFS_FS=y
CONFIG_FS_POSIX_ACL=y
CONFIG_AUTOFS_FS=y
#
# CD-ROM/DVD Filesystems
#
CONFIG_ISO9660_FS=y
CONFIG_JOLIET=y
CONFIG_UDF_FS=m
#
# DOS/FAT/NT Filesystems
#
CONFIG_FAT_FS=m
CONFIG_VFAT_FS=m
CONFIG_NTFS_FS=m
CONFIG_NTFS_RW=y
#
# Pseudo filesystems
#
CONFIG_PROC_FS=y
CONFIG_PROC_KCORE=y
CONFIG_DEVFS_FS=y
CONFIG_DEVFS_MOUNT=y
CONFIG_TMPFS=y
CONFIG_RAMFS=y
#
# Miscellaneous filesystems
#
#
# Network File Systems
#
CONFIG_SMB_FS=m
CONFIG_CIFS=m
#
# Partition Types
#
CONFIG_MSDOS_PARTITION=y
#
# Native Language Support
#
CONFIG_NLS=y
CONFIG_NLS_DEFAULT="iso8859-1"
CONFIG_NLS_CODEPAGE_437=m
CONFIG_NLS_CODEPAGE_850=m
CONFIG_NLS_ISO8859_1=m
CONFIG_NLS_UTF8=m
#
# Profiling support
#
#
# Kernel hacking
#
CONFIG_DEBUG_KERNEL=y
CONFIG_EARLY_PRINTK=y
CONFIG_DEBUG_STACKOVERFLOW=y
CONFIG_DEBUG_STACK_USAGE=y
CONFIG_DEBUG_SLAB=y
CONFIG_DEBUG_IOVIRT=y
CONFIG_MAGIC_SYSRQ=y
CONFIG_DEBUG_SPINLOCK=y
CONFIG_DEBUG_PAGEALLOC=y
CONFIG_DEBUG_HIGHMEM=y
CONFIG_DEBUG_INFO=y
CONFIG_DEBUG_SPINLOCK_SLEEP=y
CONFIG_FRAME_POINTER=y
CONFIG_X86_FIND_SMP_CONFIG=y
CONFIG_X86_MPPARSE=y
#
# Security options
#
#
# Cryptographic options
#
CONFIG_CRYPTO=y
CONFIG_CRYPTO_HMAC=y
CONFIG_CRYPTO_NULL=m
CONFIG_CRYPTO_MD4=m
CONFIG_CRYPTO_MD5=y
CONFIG_CRYPTO_SHA1=m
CONFIG_CRYPTO_SHA256=m
CONFIG_CRYPTO_SHA512=m
CONFIG_CRYPTO_DES=m
CONFIG_CRYPTO_BLOWFISH=m
CONFIG_CRYPTO_TWOFISH=m
CONFIG_CRYPTO_SERPENT=m
CONFIG_CRYPTO_AES=m
CONFIG_CRYPTO_CAST5=m
CONFIG_CRYPTO_CAST6=m
CONFIG_CRYPTO_DEFLATE=m
CONFIG_CRYPTO_TEST=m
#
# Library routines
#
CONFIG_CRC32=m
CONFIG_ZLIB_INFLATE=m
CONFIG_ZLIB_DEFLATE=m
CONFIG_X86_SMP=y
CONFIG_X86_HT=y
CONFIG_X86_BIOS_REBOOT=y
CONFIG_X86_TRAMPOLINE=y
CONFIG_PC=y
next reply other threads:[~2004-03-09 23:06 UTC|newest]
Thread overview: 8+ messages / expand[flat|nested] mbox.gz Atom feed top
2004-03-09 23:06 Andres Meyer [this message]
2004-03-10 7:22 ` Opteron SATA machine check exception (32bit) Jeff Garzik
2004-03-10 7:31 ` Andres Meyer
2004-03-10 7:37 ` Jeff Garzik
2004-03-11 21:58 ` Andres Meyer
2004-03-20 11:34 ` Jeff Garzik
2004-03-21 21:44 ` Andres Meyer
2004-03-10 11:54 ` Sergey Vlasov
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=200403100006.36405.andres.meyer@computer.org \
--to=andres.meyer@computer.org \
--cc=linux-ide@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.