From: Andres Meyer <andres.meyer@computer.org>
To: Jeff Garzik <jgarzik@pobox.com>
Cc: linux-ide@vger.kernel.org
Subject: Re: Opteron SATA machine check exception (32bit)
Date: Thu, 11 Mar 2004 22:58:32 +0100 [thread overview]
Message-ID: <200403112258.33170.andres.meyer@computer.org> (raw)
In-Reply-To: <404EC5C3.2060603@pobox.com>
> > As stated previously, It's a 32bit kernel, I did not event try 64bit SATA
> > yet.
>
> Whoops, I missed that. Thanks, I'll look into it. If you are willing,
> defining ATA_DEBUG and ATA_VERBOSE_DEBUG in include/linux/libata.h, and
> emailing dmesg output, would provide helpful details to me.
>
> Jeff
I did enable that, but there was not more output in case of crashes. I did try
to connect the 250GB SATA disks to the Promise, which seems to work ok.
The 160GB IDE Maxtor & Marvel IDE2SATA on the promise seem to trigger the mce.
I still do not have a clue why...
Andres
ata_ section from bootup:
ata_device_add: ENTER
ata_host_add: ENTER
ata_port_start: prd alloc, virt f6ae8000, dma 36ae8000
ata1: SATA max UDMA/133 cmd 0xF885C200 ctl 0xF885C238 bmdma 0x0 irq 29
ata_thread_iter: ata1: thr_state THR_PROBE_START
ata_host_add: ENTER
ata_port_start: prd alloc, virt f6adf000, dma 36adf000
ata2: SATA max UDMA/133 cmd 0xF885C280 ctl 0xF885C2B8 bmdma 0x0 irq 29
ata_thread_iter: ata2: thr_state THR_PROBE_START
ata_host_add: ENTER
ata_port_start: prd alloc, virt f6ad5000, dma 36ad5000
ata3: SATA max UDMA/133 cmd 0xF885C300 ctl 0xF885C338 bmdma 0x0 irq 29
ata_thread_iter: ata3: thr_state THR_PROBE_START
ata_host_add: ENTER
ata_port_start: prd alloc, virt f6acc000, dma 36acc000
ata4: SATA max UDMA/133 cmd 0xF885C380 ctl 0xF885C3B8 bmdma 0x0 irq 29
ata_thread_iter: ata4: thr_state THR_PROBE_START
ata_device_add: probe begin
ata_device_add: ata1: probe begin
ata_device_add: ata1: probe-wait begin
ata_thread_iter: ata1: new thr_state THR_PORT_RESET, returning 0
ata_thread_iter: ata1: thr_state THR_PORT_RESET
ata_bus_reset: ENTER, host 1, port 0
ata_bus_softreset: ata1: bus reset via SRST
ata_dev_classify: found ATA device by sig
ata_bus_reset: EXIT
ata_dev_identify: ENTER, host 1, dev 0
ata_dev_select: ENTER, ata1: device 0, wait 1
ata_dev_identify: do ATA identify
ata_exec: ata1: cmd 0xEC
ata_exec_command_mmio: ata1: cmd 0xEC
ata_dump_id: 49==0x2f00 53==0x0007 63==0x0007 64==0x0003 75==0x0000
ata_dump_id: 80==0x007e 81==0x0018 82==0x7c69 83==0x4f09 84==0x4003
ata_dump_id: 88==0x207f 93==0x600b
ata1: dev 0 ATA, max UDMA/133, 320173056 sectors (lba48)
ata_dev_identify: EXIT, drv_stat = 0x50
ata_dev_identify: ENTER/EXIT (host 1, dev 1) -- nodev
ata_host_set_udma: udma masks: host 0x7F, master 0x7F, slave 0xFF
ata_host_set_udma: mask 0x7F i 0x47 j 7
ata_host_set_udma: mask 0x7F i 0x46 j 6
ata_dev_set_xfermode: set features - xfer mode
ata_tf_load_mmio: feat 0x3 nsect 0x46 lba 0x0 0x0 0x0
ata_tf_load_mmio: device 0xA0
ata_exec: ata1: cmd 0xEF
ata_exec_command_mmio: ata1: cmd 0xEF
ata_dev_set_xfermode: EXIT
ata1: dev 0 configured for UDMA/133
ata_thread_iter: ata1: new thr_state THR_PROBE_SUCCESS, returning 0
ata_thread_iter: ata1: thr_state THR_PROBE_SUCCESS
ata_thread_iter: ata1: new thr_state THR_IDLE, returning 0
ata_device_add: ata1: probe-wait end
scsi0 : sata_promise
ata_device_add: ata2: probe begin
ata_device_add: ata2: probe-wait begin
ata_thread_iter: ata2: new thr_state THR_PORT_RESET, returning 0
ata_thread_iter: ata2: thr_state THR_PORT_RESET
ata_bus_reset: ENTER, host 2, port 1
ata_bus_softreset: ata2: bus reset via SRST
ata_dev_classify: found ATA device by sig
ata_bus_reset: EXIT
ata_dev_identify: ENTER, host 2, dev 0
ata_dev_select: ENTER, ata2: device 0, wait 1
ata_dev_identify: do ATA identify
ata_exec: ata2: cmd 0xEC
ata_exec_command_mmio: ata2: cmd 0xEC
ata_dump_id: 49==0x2f00 53==0x0007 63==0x0007 64==0x0003 75==0x0000
ata_dump_id: 80==0x007e 81==0x0018 82==0x7c69 83==0x4f09 84==0x4003
ata_dump_id: 88==0x207f 93==0x600b
ata2: dev 0 ATA, max UDMA/133, 320173056 sectors (lba48)
ata_dev_identify: EXIT, drv_stat = 0x50
ata_dev_identify: ENTER/EXIT (host 2, dev 1) -- nodev
ata_host_set_udma: udma masks: host 0x7F, master 0x7F, slave 0xFF
ata_host_set_udma: mask 0x7F i 0x47 j 7
ata_host_set_udma: mask 0x7F i 0x46 j 6
ata_dev_set_xfermode: set features - xfer mode
ata_tf_load_mmio: feat 0x3 nsect 0x46 lba 0x0 0x0 0x0
ata_tf_load_mmio: device 0xA0
ata_exec: ata2: cmd 0xEF
ata_exec_command_mmio: ata2: cmd 0xEF
ata_dev_set_xfermode: EXIT
ata2: dev 0 configured for UDMA/133
ata_thread_iter: ata2: new thr_state THR_PROBE_SUCCESS, returning 0
ata_thread_iter: ata2: thr_state THR_PROBE_SUCCESS
ata_thread_iter: ata2: new thr_state THR_IDLE, returning 0
ata_thread_iter: ata2: thr_state THR_IDLE
ata_thread_iter: ata2: new thr_state THR_IDLE, returning 30000
ata_device_add: ata2: probe-wait end
scsi1 : sata_promise
ata_device_add: ata3: probe begin
ata_device_add: ata3: probe-wait begin
ata_thread_iter: ata3: new thr_state THR_PORT_RESET, returning 0
ata_thread_iter: ata3: thr_state THR_PORT_RESET
ata_bus_reset: ENTER, host 3, port 2
ata_bus_softreset: ata3: bus reset via SRST
ata_dev, ata3, use_sg 1
<3>ata_sg_setup: 1 sg elements mapped
pdc_fill_sg: ENTER
ata_fill_sg: PRD[0] = (0x36B82000, 0x1000)
pdc_dma_start: ENTER, ap f6ad99c4
ata_scsi_rw_queue: EXIT
pdc_interrupt: ENTER
pdc_interrupt: port 0
pdc_interrupt: port 1
pdc_interrupt: port 2
ata_sg_clean: unmapping 1 sg elements
pdc_interrupt: port 3
pdc_interrupt: EXIT
p5 >
Attached scsi disk sdc at scsi2, channel 0, id 0, lun 0
ata_scsi_queuecmd: CDB (4:0,0,0) 00 00 00 00 00 00 00 00 00
ata_scsiop_noop: ENTER
ata_scsi_queuecmd: CDB (4:0,0,0) 25 00 00 00 00 00 00 00 00
ata_scsiop_read_cap: ENTER
SCSI device sdd: 320173056 512-byte hdwr sectors (163929 MB)
ata_scsi_queuecmd: CDB (4:0,0,0) 5a 00 08 00 00 00 00 00 08
ata_scsiop_mode_sense: ENTER
ata_scsi_queuecmd: CDB (4:0,0,0) 5a 00 08 00 00 00 00 00 17
ata_scsiop_mode_sense: ENTER
SCSI device sdd: drive cache: write through
/dev/scsi/host3/bus0/target0/lun0:<3>ata_scsi_queuecmd: CDB (4:0,0,0) 28 00
00 00 00 00 00 00 08
ata_scsi_rw_queue: ENTER
ata_scsi_rw_xlat: reading
ata_scsi_rw_xlat: ten-byte command
ata_dev_select: ENTER, ata4: device 0, wait 1
ata_sg_setup: ENTER, ata4, use_sg 1
ata_sg_setup: 1 sg elements mapped
pdc_fill_sg: ENTER
ata_fill_sg: PRD[0] = (0x36B81000, 0x1000)
pdc_dma_start: ENTER, ap f6ad09c4
ata_scsi_rw_queue: EXIT
pdc_interrupt: ENTER
pdc_interrupt: port 0
pdc_interrupt: port 1
pdc_interrupt: port 2
pdc_interrupt: port 3
ata_sg_clean: unmapping 1 sg elements
pdc_interrupt: EXIT
p1 <<3>ata_scsi_queuecmd: CDB (4:0,0,0) 28 00 00 00 3e c0 00 00 08
ata_scsi_rw_queue: ENTER
ata_scsi_rw_xlat: reading
ata_scsi_rw_xlat: ten-byte command
ata_dev_select: ENTER, ata4: device 0, wait 1
ata_sg_setup: ENTER, ata4, use_sg 1
ata_sg_setup: 1 sg elements mapped
pdc_fill_sg: ENTER
ata_fill_sg: PRD[0] = (0x36B80000, 0x1000)
pdc_dma_start: ENTER, ap f6ad09c4
ata_scsi_rw_queue: EXIT
pdc_interrupt: ENTER
pdc_interrupt: port 0
pdc_interrupt: port 1
pdc_interrupt: port 2
pdc_interrupt: port 3
ata_sg_clean: unmapping 1 sg elements
pdc_interrupt: EXIT
p5 >
Attached scsi disk sdd at scsi3, channel 0, id 0, lun 0
ata_scsi_queuecmd: CDB (5:0,0,0) 00 00 00 00 00 00 00 00 00
ata_scsiop_noop: ENTER
ata_scsi_queuecmd: CDB (5:0,0,0) 25 00 00 00 00 00 00 00 00
ata_scsiop_read_cap: ENTER
SCSI device sde: 490234752 512-byte hdwr sectors (251000 MB)
ata_scsi_queuecmd: CDB (5:0,0,0) 5a 00 08 00 00 00 00 00 08
ata_scsiop_mode_sense: ENTER
ata_scsi_queuecmd: CDB (5:0,0,0) 5a 00 08 00 00 00 00 00 17
ata_scsiop_mode_sense: ENTER
SCSI device sde: drive cache: write through
/dev/scsi/host4/bus0/target0/lun0:<3>ata_scsi_queuecmd: CDB (5:0,0,0) 28 00
00 00 00 00 00 00 08
ata_scsi_rw_queue: ENTER
ata_scsi_rw_xlat: reading
ata_scsi_rw_xlat: ten-byte command
ata_dev_select: ENTER, ata5: device 0, wait 1
ata_sg_setup: ENTER, ata5, use_sg 1
ata_sg_setup: 1 sg elements mapped
ata_fill_sg: PRD[0] = (0x36B7F000, 0x1000)
ata_tf_load_mmio: hob: feat 0x0 nsect 0x0, lba 0x0 0x0 0x0
ata_tf_load_mmio: feat 0x0 nsect 0x8 lba 0x0 0x0 0x0
ata_tf_load_mmio: device 0xE0
ata_exec_command_mmio: ata5: cmd 0x25
ata_scsi_rw_queue: EXIT
ata_host_intr: BUS_DMA (host_stat 0x4)
ata_dma_complete: ENTER
ata_dma_complete: host 5, host_stat==0x4, drv_stat==0x50
ata_sg_clean: unmapping 1 sg elements
p1 <<3>ata_scsi_queuecmd: CDB (5:0,0,0) 28 00 00 00 00 38 00 00 08
ata_scsi_rw_queue: ENTER
ata_scsi_rw_xlat: reading
ata_scsi_rw_xlat: ten-byte command
ata_dev_select: ENTER, ata5: device 0, wait 1
ata_sg_setup: ENTER, ata5, use_sg 1
ata_sg_setup: 1 sg elements mapped
ata_fill_sg: PRD[0] = (0x36B7E000, 0x1000)
ata_tf_load_mmio: hob: feat 0x0 nsect 0x0, lba 0x0 0x0 0x0
ata_tf_load_mmio: feat 0x0 nsect 0x8 lba 0x38 0x0 0x0
ata_tf_load_mmio: device 0xE0
ata_exec_command_mmio: ata5: cmd 0x25
ata_scsi_rw_queue: EXIT
ata_host_intr: BUS_DMA (host_stat 0x4)
ata_dma_complete: ENTER
ata_dma_complete: host 5, host_stat==0x4, drv_stat==0x50
ata_sg_clean: unmapping 1 sg elements
p5 >
Attached scsi disk sde at scsi4, channel 0, id 0, lun 0
ata_scsi_queuecmd: CDB (6:0,0,0) 00 00 00 00 00 00 00 00 00
ata_scsiop_noop: ENTER
ata_scsi_queuecmd: CDB (6:0,0,0) 25 00 00 00 00 00 00 00 00
ata_scsiop_read_cap: ENTER
SCSI device sdf: 490234752 512-byte hdwr sectors (251000 MB)
ata_scsi_queuecmd: CDB (6:0,0,0) 5a 00 08 00 00 00 00 00 08
ata_scsiop_mode_sense: ENTER
ata_scsi_queuecmd: CDB (6:0,0,0) 5a 00 08 00 00 00 00 00 17
ata_scsiop_mode_sense: ENTER
SCSI device sdf: drive cache: write through
/dev/scsi/host5/bus0/target0/lun0:<3>ata_scsi_queuecmd: CDB (6:0,0,0) 28 00
00 00 00 00 00 00 08
ata_scsi_rw_queue: ENTER
ata_scsi_rw_xlat: reading
ata_scsi_rw_xlat: ten-byte command
ata_dev_select: ENTER, ata6: device 0, wait 1
ata_sg_setup: ENTER, ata6, use_sg 1
ata_sg_setup: 1 sg elements mapped
ata_fill_sg: PRD[0] = (0x3674D000, 0x1000)
ata_tf_load_mmio: hob: feat 0x0 nsect 0x0, lba 0x0 0x0 0x0
ata_tf_load_mmio: feat 0x0 nsect 0x8 lba 0x0 0x0 0x0
ata_tf_load_mmio: device 0xE0
ata_exec_command_mmio: ata6: cmd 0x25
ata_scsi_rw_queue: EXIT
ata_host_intr: BUS_DMA (host_stat 0x4)
ata_dma_complete: ENTER
ata_dma_complete: host 6, host_stat==0x4, drv_stat==0x50
ata_sg_clean: unmapping 1 sg elements
p1 <<3>ata_scsi_queuecmd: CDB (6:0,0,0) 28 00 00 00 00 38 00 00 08
ata_scsi_rw_queue: ENTER
ata_scsi_rw_xlat: reading
ata_scsi_rw_xlat: ten-byte command
ata_dev_select: ENTER, ata6: device 0, wait 1
ata_sg_setup: ENTER, ata6, use_sg 1
ata_sg_setup: 1 sg elements mapped
ata_fill_sg: PRD[0] = (0x3674C000, 0x1000)
ata_tf_load_mmio: hob: feat 0x0 nsect 0x0, lba 0x0 0x0 0x0
ata_tf_load_mmio: feat 0x0 nsect 0x8 lba 0x38 0x0 0x0
ata_tf_load_mmio: device 0xE0
ata_exec_command_mmio: ata6: cmd 0x25
ata_scsi_rw_queue: EXIT
ata_host_intr: BUS_DMA (host_stat 0x4)
ata_dma_complete: ENTER
ata_dma_complete: host 6, host_stat==0x4, drv_stat==0x50
ata_sg_clean: unmapping 1 sg elements
p5 >
Attached scsi disk sdf at scsi5, channel 0, id 0, lun 0
Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0
Attached scsi generic sg1 at scsi1, channel 0, id 0, lun 0, type 0
Attached scsi generic sg2 at scsi2, channel 0, id 0, lun 0, type 0
Attached scsi generic sg3 at scsi3, channel 0, id 0, lun 0, type 0
Attached scsi generic sg4 at scsi4, channel 0, id 0, lun 0, type 0
Attached scsi generic sg5 at scsi5, channel 0, id 0, lun 0, type 0
next prev parent reply other threads:[~2004-03-11 21:59 UTC|newest]
Thread overview: 8+ messages / expand[flat|nested] mbox.gz Atom feed top
2004-03-09 23:06 Opteron SATA machine check exception (32bit) Andres Meyer
2004-03-10 7:22 ` Jeff Garzik
2004-03-10 7:31 ` Andres Meyer
2004-03-10 7:37 ` Jeff Garzik
2004-03-11 21:58 ` Andres Meyer [this message]
2004-03-20 11:34 ` Jeff Garzik
2004-03-21 21:44 ` Andres Meyer
2004-03-10 11:54 ` Sergey Vlasov
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=200403112258.33170.andres.meyer@computer.org \
--to=andres.meyer@computer.org \
--cc=jgarzik@pobox.com \
--cc=linux-ide@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.