* Re: Linux 2.6.7-mm1, IBM T40p, ACPI C3 finally working. [not found] <200406211951.03333@zodiac.zodiac.dnsalias.org> @ 2004-06-25 2:06 ` Alexander Gran 2004-06-25 2:51 ` Adam Sulmicki 0 siblings, 1 reply; 8+ messages in thread From: Alexander Gran @ 2004-06-25 2:06 UTC (permalink / raw) To: linux-kernel; +Cc: linux-thinkpad [-- Attachment #1: Type: text/plain, Size: 12229 bytes --] Ok guys, now this is strange. since 2.6.7-mm2 C3 does not work any longer. No idea why. Same config, same system: IBM t40p, 2373-g1g. lspci -vvv: root@t40:~# lspci -vvv 0000:00:00.0 Host bridge: Intel Corp. 82855PM Processor to I/O Controller (rev 03) Subsystem: IBM: Unknown device 0529 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- Latency: 0 Region 0: Memory at d0000000 (32-bit, prefetchable) Capabilities: [e4] #09 [f104] Capabilities: [a0] AGP version 2.0 Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4 Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW- Rate=x2 0000:00:01.0 PCI bridge: Intel Corp. 82855PM Processor to AGP Controller (rev 03) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 96 Bus: primary=00, secondary=01, subordinate=01, sec-latency=64 I/O behind bridge: 00003000-00003fff Memory behind bridge: c0100000-c01fffff Prefetchable memory behind bridge: e0000000-e7ffffff Expansion ROM at 00003000 [disabled] [size=4K] BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B- 0000:00:1d.0 USB Controller: Intel Corp. 82801DB (ICH4) USB UHCI #1 (rev 01) (prog-if 00 [UHCI]) Subsystem: IBM: Unknown device 052d Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin A routed to IRQ 9 Region 4: I/O ports at 1800 [size=32] 0000:00:1d.1 USB Controller: Intel Corp. 82801DB (ICH4) USB UHCI #2 (rev 01) (prog-if 00 [UHCI]) Subsystem: IBM: Unknown device 052d Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin B routed to IRQ 10 Region 4: I/O ports at 1820 [size=32] 0000:00:1d.2 USB Controller: Intel Corp. 82801DB (ICH4) USB UHCI #3 (rev 01) (prog-if 00 [UHCI]) Subsystem: IBM: Unknown device 052d Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin C routed to IRQ 11 Region 4: I/O ports at 1840 [size=32] 0000:00:1d.7 USB Controller: Intel Corp. 82801DB (ICH4) USB2 EHCI Controller (rev 01) (prog-if 20 [EHCI]) Subsystem: IBM: Unknown device 052e Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin D routed to IRQ 10 Region 0: Memory at c0000000 (32-bit, non-prefetchable) Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [58] #0a [2080] 0000:00:1e.0 PCI bridge: Intel Corp. 82801BAM/CAM PCI Bridge (rev 81) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR+ Latency: 0 Bus: primary=00, secondary=02, subordinate=08, sec-latency=168 I/O behind bridge: 00004000-00008fff Memory behind bridge: c0200000-cfffffff Prefetchable memory behind bridge: e8000000-efffffff BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B- 0000:00:1f.0 ISA bridge: Intel Corp. 82801DBM LPC Interface Controller (rev 01) Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 0000:00:1f.1 IDE interface: Intel Corp. 82801DBM (ICH4) Ultra ATA Storage Controller (rev 01) (prog-if 8a [Master SecP PriP]) Subsystem: IBM: Unknown device 052d Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin A routed to IRQ 11 Region 0: I/O ports at <unassigned> Region 1: I/O ports at <unassigned> Region 2: I/O ports at <unassigned> Region 3: I/O ports at <unassigned> Region 4: I/O ports at 1860 [size=16] Region 5: Memory at 20000000 (32-bit, non-prefetchable) [size=1K] 0000:00:1f.3 SMBus: Intel Corp. 82801DB/DBM (ICH4) SMBus Controller (rev 01) Subsystem: IBM: Unknown device 052d Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Interrupt: pin B routed to IRQ 10 Region 4: I/O ports at 1880 [size=32] 0000:00:1f.5 Multimedia audio controller: Intel Corp. 82801DB (ICH4) AC'97 Audio Controller (rev 01) Subsystem: IBM: Unknown device 0537 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin B routed to IRQ 10 Region 0: I/O ports at 1c00 Region 1: I/O ports at 18c0 [size=64] Region 2: Memory at c0000c00 (32-bit, non-prefetchable) [size=512] Region 3: Memory at c0000800 (32-bit, non-prefetchable) [size=256] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 0000:00:1f.6 Modem: Intel Corp. 82801DB (ICH4) AC'97 Modem Controller (rev 01) (prog-if 00 [Generic]) Subsystem: IBM: Unknown device 0525 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin B routed to IRQ 10 Region 0: I/O ports at 2400 Region 1: I/O ports at 2000 [size=128] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 0000:01:00.0 VGA compatible controller: ATI Technologies Inc Radeon R250 Lf [Radeon Mobility 9000 M9] (rev 02) (prog-if 00 [VGA]) Subsystem: IBM: Unknown device 054d Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR+ FastB2B+ Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 66 (2000ns min), Cache Line Size: 0x08 (32 bytes) Interrupt: pin A routed to IRQ 9 Region 0: Memory at e0000000 (32-bit, prefetchable) Region 1: I/O ports at 3000 [size=256] Region 2: Memory at c0100000 (32-bit, non-prefetchable) [size=64K] Capabilities: [58] AGP version 2.0 Status: RQ=48 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4 Command: RQ=32 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW- Rate=x2 Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 0000:02:00.0 CardBus bridge: Texas Instruments PCI1520 PC card Cardbus Controller (rev 01) Subsystem: IBM ThinkPad T30/T40 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 168, Cache Line Size: 0x20 (128 bytes) Interrupt: pin A routed to IRQ 9 Region 0: Memory at b0000000 (32-bit, non-prefetchable) Bus: primary=02, secondary=03, subordinate=06, sec-latency=176 Memory window 0: 20400000-207ff000 (prefetchable) Memory window 1: 20800000-20bff000 I/O window 0: 00004000-000040ff I/O window 1: 00004400-000044ff BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+ 16-bit legacy interface ports at 0001 0000:02:00.1 CardBus bridge: Texas Instruments PCI1520 PC card Cardbus Controller (rev 01) Subsystem: IBM ThinkPad T30/T40 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 168, Cache Line Size: 0x20 (128 bytes) Interrupt: pin B routed to IRQ 10 Region 0: Memory at b1000000 (32-bit, non-prefetchable) Bus: primary=02, secondary=07, subordinate=0a, sec-latency=176 Memory window 0: 20c00000-20fff000 (prefetchable) Memory window 1: 21000000-213ff000 I/O window 0: 00004800-000048ff I/O window 1: 00004c00-00004cff BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+ 16-bit legacy interface ports at 0001 0000:02:01.0 Ethernet controller: Intel Corp. 82540EP Gigabit Ethernet Controller (Mobile) (rev 03) Subsystem: IBM PRO/1000 MT Mobile Connection Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 (63750ns min), Cache Line Size: 0x08 (32 bytes) Interrupt: pin A routed to IRQ 9 Region 0: Memory at c0220000 (32-bit, non-prefetchable) Region 1: Memory at c0200000 (32-bit, non-prefetchable) [size=64K] Region 2: I/O ports at 8000 [size=64] Capabilities: [dc] Power Management version 2 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=1 PME- Capabilities: [f0] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable- Address: 0000000000000000 Data: 0000 0000:02:02.0 Ethernet controller: Atheros Communications, Inc. AR5211 802.11ab NIC (rev 01) Subsystem: Unknown device 17ab:8310 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 80 (2500ns min, 7000ns max), Cache Line Size: 0x08 (32 bytes) Interrupt: pin A routed to IRQ 11 Region 0: Memory at c0210000 (32-bit, non-prefetchable) Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=2 PME- dmesges attached. regards Alex Am Montag, 21. Juni 2004 19:50 schrieb Alexander Gran: > Hi, > > just a quick note: > Since 2.6.7-mm1 acpi C3 works even with usb and radeon loaded. > Great work! > > regards > Alex -- Encrypted Mails welcome. PGP-Key at http://zodiac.dnsalias.org/misc/pgpkey.asc | Key-ID: 0x6D7DD291 [-- Attachment #2: dmesg-2.6.7-mm1 --] [-- Type: text/plain, Size: 28905 bytes --] Linux version 2.6.7-mm1 (root@t40) (gcc version 3.3.4 (Debian)) #1 Mon Jun 21 03:57:38 CEST 2004 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009f000 (usable) BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved) BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000001ff60000 (usable) BIOS-e820: 000000001ff60000 - 000000001ff77000 (ACPI data) BIOS-e820: 000000001ff77000 - 000000001ff79000 (ACPI NVS) BIOS-e820: 000000001ff80000 - 0000000020000000 (reserved) BIOS-e820: 00000000ff800000 - 0000000100000000 (reserved) 511MB LOWMEM available. On node 0 totalpages: 130912 DMA zone: 4096 pages, LIFO batch:1 Normal zone: 126816 pages, LIFO batch:16 HighMem zone: 0 pages, LIFO batch:1 DMI present. IBM machine detected. Enabling interrupts during APM calls. IBM machine detected. Disabling SMBus accesses. ACPI: RSDP (v002 IBM ) @ 0x000f6e00 ACPI: XSDT (v001 IBM TP-1R 0x00003051 LTP 0x00000000) @ 0x1ff6af83 ACPI: FADT (v003 IBM TP-1R 0x00003051 IBM 0x00000001) @ 0x1ff6b000 ACPI: SSDT (v001 IBM TP-1R 0x00003051 MSFT 0x0100000e) @ 0x1ff6b1b4 ACPI: ECDT (v001 IBM TP-1R 0x00003051 IBM 0x00000001) @ 0x1ff76e06 ACPI: TCPA (v001 IBM TP-1R 0x00003051 PTL 0x00000001) @ 0x1ff76e58 ACPI: BOOT (v001 IBM TP-1R 0x00003051 LTP 0x00000001) @ 0x1ff76fd8 ACPI: DSDT (v001 IBM TP-1R 0x00003051 MSFT 0x0100000e) @ 0x00000000 Built 1 zonelists Local APIC disabled by BIOS -- reenabling. Found and enabled local APIC! Initializing CPU#0 Kernel command line: BOOT_IMAGE=Linux2.6.7-mm1 ro root=306 quiet CPU 0 irqstacks, hard=c050a000 soft=c0509000 PID hash table entries: 2048 (order 11: 16384 bytes) Detected 1595.001 MHz processor. Using tsc for high-res timesource Console: colour VGA+ 80x25 Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 512528k/523648k available (2721k kernel code, 10352k reserved, 1221k data, 176k init, 0k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay loop... 3153.92 BogoMIPS Mount-cache hash table entries: 512 (order: 0, 4096 bytes) CPU: After generic identify, caps: a7e9fbbf 00000000 00000000 00000000 CPU: After vendor identify, caps: a7e9fbbf 00000000 00000000 00000000 CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 1024K CPU: After all inits, caps: a7e9fbbf 00000000 00000000 00000040 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. CPU: Intel(R) Pentium(R) M processor 1600MHz stepping 05 Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Checking 'hlt' instruction... OK. enabled ExtINT on CPU#0 ESR value before enabling vector: 00000000 ESR value after enabling vector: 00000000 Using local APIC timer interrupts. calibrating APIC timer ... ..... CPU clock speed is 1594.0574 MHz. ..... host bus clock speed is 99.0660 MHz. NET: Registered protocol family 16 PCI: PCI BIOS revision 2.10 entry at 0xfd8d6, last bus=8 PCI: Using configuration type 1 mtrr: v2.0 (20020519) ACPI: Subsystem revision 20040326 ACPI-0291: *** Info: Table [DSDT] replaced by host OS ACPI: IRQ9 SCI: Level Trigger. ACPI: Found ECDT ACPI: Interpreter enabled ACPI: Using PIC for interrupt routing ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *9 10 11) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 *10 11) ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 *11) ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 *10 11) ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 *10 11) ACPI: PCI Root Bridge [PCI0] (00:00) PCI: Probing PCI hardware (bus 00) PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1 PCI: Transparent bridge - 0000:00:1e.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: Embedded Controller [EC] (gpe 28) ACPI: Power Resource [PUBS] (on) ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT] Linux Plug and Play Support v0.97 (c) Adam Belay PnPBIOS: Scanning system for PnP BIOS support... PnPBIOS: Found PnP BIOS installation structure at 0xc00f6e30 PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0xb699, dseg 0x400 pnp: 00:0b: ioport range 0x4d0-0x4d1 has been reserved pnp: 00:0b: ioport range 0x1000-0x105f has been reserved pnp: 00:0b: ioport range 0x1060-0x107f has been reserved pnp: 00:0b: ioport range 0x1180-0x11bf has been reserved PnPBIOS: 19 nodes reported by PnP BIOS; 19 recorded by driver SCSI subsystem initialized Linux Kernel Card Services options: [pci] [cardbus] [pm] PCI: Using ACPI for IRQ routing ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 9 ACPI: PCI interrupt 0000:00:1d.0[A] -> GSI 9 (level, low) -> IRQ 9 ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 10 ACPI: PCI interrupt 0000:00:1d.1[B] -> GSI 10 (level, low) -> IRQ 10 ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11 ACPI: PCI interrupt 0000:00:1d.2[C] -> GSI 11 (level, low) -> IRQ 11 ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 10 ACPI: PCI interrupt 0000:00:1d.7[D] -> GSI 10 (level, low) -> IRQ 10 ACPI: PCI interrupt 0000:00:1f.1[A] -> GSI 11 (level, low) -> IRQ 11 ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10 ACPI: PCI interrupt 0000:00:1f.3[B] -> GSI 10 (level, low) -> IRQ 10 ACPI: PCI interrupt 0000:00:1f.5[B] -> GSI 10 (level, low) -> IRQ 10 ACPI: PCI interrupt 0000:00:1f.6[B] -> GSI 10 (level, low) -> IRQ 10 ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 9 (level, low) -> IRQ 9 ACPI: PCI interrupt 0000:02:00.0[A] -> GSI 9 (level, low) -> IRQ 9 ACPI: PCI interrupt 0000:02:00.1[B] -> GSI 10 (level, low) -> IRQ 10 ACPI: PCI interrupt 0000:02:01.0[A] -> GSI 9 (level, low) -> IRQ 9 ACPI: PCI interrupt 0000:02:02.0[A] -> GSI 11 (level, low) -> IRQ 11 NET: Registered protocol family 23 Bluetooth: Core ver 2.5 NET: Registered protocol family 31 Bluetooth: HCI device and connection manager initialized Bluetooth: HCI socket layer initialized ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 9 (level, low) -> IRQ 9 radeonfb: Invalid ROM signature 0 should be 0xaa55 radeonfb: Retreived PLL infos from BIOS radeonfb: Reference=27.00 MHz (RefDiv=12) Memory=252.00 Mhz, System=200.00 MHz Non-DDC laptop panel detected radeonfb: Monitor 1 type LCD found radeonfb: Monitor 2 type no found radeonfb: panel ID string: SXGA+ Single (85MHz) radeonfb: detected LVDS panel size from BIOS: 1400x1050 radeondb: BIOS provided dividers will be used radeonfb: Power Management enabled for Mobility chipsets radeonfb: ATI Radeon Lf DDR SGRAM 64 MB Simple Boot Flag at 0x35 set to 0x1 Machine check exception polling timer started. apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac) apm: overridden by ACPI. udf: registering filesystem Initializing Cryptographic API isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found Console: switching to colour frame buffer device 175x65 lp: driver loaded but no devices found Real Time Clock Driver v1.12 Non-volatile memory driver v1.2 Linux agpgart interface v0.100 (c) Dave Jones agpgart: Detected an Intel 855PM Chipset. agpgart: Maximum main memory to use for agp memory: 439M agpgart: AGP aperture is 256M @ 0xd0000000 [drm] Initialized radeon 1.11.0 20020828 on minor 0: ATI Technologies Inc Radeon R250 Lf [Radeon Mobility 9000 M9] Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing enabled ttyS1 at I/O 0x2f8 (irq = 3) is a NS16550A ACPI: PCI interrupt 0000:00:1f.6[B] -> GSI 10 (level, low) -> IRQ 10 pnp: Device 00:12 activated. ttyS0 at I/O 0x3f8 (irq = 4) is a NS16550A parport: PnPBIOS parport detected. parport0: PC-style at 0x3bc (0x7bc), irq 7, dma 1 [PCSPP,TRISTATE,COMPAT,ECP,DMA] lp0: using parport0 (interrupt-driven). RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize loop: loaded (max 8 devices) PPP generic driver version 2.4.2 PPP Deflate Compression module registered PPP BSD Compression module registered NET: Registered protocol family 24 Universal TUN/TAP device driver 1.5 (C)1999-2002 Maxim Krasnyansky Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx ICH4: IDE controller at PCI slot 0000:00:1f.1 PCI: Enabling device 0000:00:1f.1 (0005 -> 0007) ACPI: PCI interrupt 0000:00:1f.1[A] -> GSI 11 (level, low) -> IRQ 11 ICH4: chipset revision 1 ICH4: not 100% native mode: will probe irqs later ide0: BM-DMA at 0x1860-0x1867, BIOS settings: hda:DMA, hdb:pio ide1: BM-DMA at 0x1868-0x186f, BIOS settings: hdc:DMA, hdd:pio hda: IC25N040ATCS05-0, ATA DISK drive Using anticipatory io scheduler ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 hdc: UJDA745 DVD/CDRW, ATAPI CD/DVD-ROM drive ide1 at 0x170-0x177,0x376 on irq 15 hda: max request size: 128KiB hda: 78140160 sectors (40007 MB) w/7898KiB Cache, CHS=65535/16/63, UDMA(100) hda: cache flushes supported hda: hda1 hda2 hda3 < hda5 hda6 hda7 > hda4 hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33) Uniform CD-ROM driver Revision: 3.20 ACPI: PCI interrupt 0000:02:00.0[A] -> GSI 9 (level, low) -> IRQ 9 Yenta: CardBus bridge found at 0000:02:00.0 [1014:0512] Yenta: Using INTVAL to route CSC interrupts to PCI Yenta: Routing CardBus interrupts to PCI Yenta TI: socket 0000:02:00.0, mfunc 0x01d21022, devctl 0x64 Yenta: ISA IRQ mask 0x0078, PCI irq 9 Socket status: 30000006 ACPI: PCI interrupt 0000:02:00.1[B] -> GSI 10 (level, low) -> IRQ 10 Yenta: CardBus bridge found at 0000:02:00.1 [1014:0512] Yenta: Using INTVAL to route CSC interrupts to PCI Yenta: Routing CardBus interrupts to PCI Yenta TI: socket 0000:02:00.1, mfunc 0x01d21022, devctl 0x64 Yenta: ISA IRQ mask 0x0078, PCI irq 10 Socket status: 30000006 serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 mice: PS/2 mouse device common for all mice input: AT Translated Set 2 keyboard on isa0060/serio0 Synaptics Touchpad, model: 1 Firmware: 5.9 Sensor: 44 new absolute packet format Touchpad has extended capability bits -> multifinger detection -> palm detection -> pass-through port input: SynPS/2 Synaptics TouchPad on isa0060/serio1 serio: Synaptics pass-through port at isa0060/serio1/input0 input: PS/2 Generic Mouse on synaptics-pt/serio0 input: PC Speaker Advanced Linux Sound Architecture Driver Version 1.0.5 (Sun May 30 10:49:40 2004 UTC). ALSA device list: No soundcards found. NET: Registered protocol family 2 IP: routing cache hash table of 4096 buckets, 32Kbytes TCP: Hash tables configured (established 32768 bind 65536) Initializing IPsec netlink socket NET: Registered protocol family 1 NET: Registered protocol family 10 IPv6 over IPv4 tunneling driver NET: Registered protocol family 17 IrCOMM protocol (Dag Brattli) Bluetooth: L2CAP ver 2.2 Bluetooth: L2CAP socket layer initialized Bluetooth: SCO (Voice Link) ver 0.3 Bluetooth: SCO socket layer initialized Bluetooth: RFCOMM ver 1.3 Bluetooth: RFCOMM socket layer initialized Bluetooth: RFCOMM TTY layer initialized Bluetooth: BNEP (Ethernet Emulation) ver 1.0 Bluetooth: BNEP filters: protocol multicast speedstep-centrino: found "Intel(R) Pentium(R) M processor 1600MHz": max frequency: 1600000kHz PM: Reading pmdisk image. PM: Resume from disk failed. ACPI: (supports S0 S3 S4 S5) kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) readonly. Freeing unused kernel memory: 176k freed Adding 498920k swap on /dev/hda5. Priority:-1 extents:1 EXT3 FS on hda6, internal journal kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 600 seconds EXT3 FS on hda4, internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 600 seconds EXT3 FS on hda7, internal journal EXT3-fs: mounted filesystem with ordered data mode. usbcore: registered new driver usbfs usbcore: registered new driver hub USB Universal Host Controller Interface driver v2.2 ACPI: PCI interrupt 0000:00:1d.0[A] -> GSI 9 (level, low) -> IRQ 9 uhci_hcd 0000:00:1d.0: Intel Corp. 82801DB (ICH4) USB UHCI #1 PCI: Setting latency timer of device 0000:00:1d.0 to 64 uhci_hcd 0000:00:1d.0: irq 9, io base 00001800 uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1 uhci_hcd 0000:00:1d.0: detected 2 ports usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: default language 0x0409 usb usb1: Product: Intel Corp. 82801DB (ICH4) USB UHCI #1 usb usb1: Manufacturer: Linux 2.6.7-mm1 uhci_hcd usb usb1: SerialNumber: 0000:00:1d.0 usb usb1: hotplug usb usb1: adding 1-0:1.0 (config #1, interface 0) usb 1-0:1.0: hotplug hub 1-0:1.0: usb_probe_interface hub 1-0:1.0: usb_probe_interface - got id hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected hub 1-0:1.0: standalone hub hub 1-0:1.0: no power switching (usb 1.0) hub 1-0:1.0: individual port over-current protection hub 1-0:1.0: power on to power good time: 2ms hub 1-0:1.0: local power source is good ACPI: PCI interrupt 0000:00:1d.1[B] -> GSI 10 (level, low) -> IRQ 10 uhci_hcd 0000:00:1d.1: Intel Corp. 82801DB (ICH4) USB UHCI #2 PCI: Setting latency timer of device 0000:00:1d.1 to 64 uhci_hcd 0000:00:1d.1: irq 10, io base 00001820 uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2 uhci_hcd 0000:00:1d.1: detected 2 ports usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1 usb usb2: default language 0x0409 usb usb2: Product: Intel Corp. 82801DB (ICH4) USB UHCI #2 usb usb2: Manufacturer: Linux 2.6.7-mm1 uhci_hcd usb usb2: SerialNumber: 0000:00:1d.1 usb usb2: hotplug usb usb2: adding 2-0:1.0 (config #1, interface 0) usb 2-0:1.0: hotplug hub 2-0:1.0: usb_probe_interface hub 2-0:1.0: usb_probe_interface - got id hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected hub 2-0:1.0: standalone hub hub 2-0:1.0: no power switching (usb 1.0) hub 2-0:1.0: individual port over-current protection hub 2-0:1.0: power on to power good time: 2ms hub 2-0:1.0: local power source is good ACPI: PCI interrupt 0000:00:1d.2[C] -> GSI 11 (level, low) -> IRQ 11 uhci_hcd 0000:00:1d.2: Intel Corp. 82801DB (ICH4) USB UHCI #3 uhci_hcd 0000:00:1d.1: port 1 portsc 0093 hub 2-0:1.0: port 1, status 0101, change 0001, 12 Mb/s PCI: Setting latency timer of device 0000:00:1d.2 to 64 uhci_hcd 0000:00:1d.2: irq 11, io base 00001840 uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3 uhci_hcd 0000:00:1d.2: detected 2 ports usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1 usb usb3: default language 0x0409 usb usb3: Product: Intel Corp. 82801DB (ICH4) USB UHCI #3 usb usb3: Manufacturer: Linux 2.6.7-mm1 uhci_hcd usb usb3: SerialNumber: 0000:00:1d.2 usb usb3: hotplug usb usb3: adding 3-0:1.0 (config #1, interface 0) usb 3-0:1.0: hotplug hub 3-0:1.0: usb_probe_interface hub 3-0:1.0: usb_probe_interface - got id hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected hub 3-0:1.0: standalone hub hub 3-0:1.0: no power switching (usb 1.0) hub 3-0:1.0: individual port over-current protection hub 3-0:1.0: power on to power good time: 2ms hub 3-0:1.0: local power source is good hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x101 usb 2-1: new full speed USB device using address 2 usb 2-1: new device strings: Mfr=0, Product=0, SerialNumber=0 usb 2-1: hotplug usb 2-1: adding 2-1:1.0 (config #1, interface 0) usb 2-1:1.0: hotplug hub 2-1:1.0: usb_probe_interface hub 2-1:1.0: usb_probe_interface - got id hub 2-1:1.0: USB hub found hub 2-1:1.0: 4 ports detected hub 2-1:1.0: standalone hub hub 2-1:1.0: individual port power switching hub 2-1:1.0: individual port over-current protection hub 2-1:1.0: Port indicators are supported hub 2-1:1.0: power on to power good time: 100ms hub 2-1:1.0: local power source is good hub 2-1:1.0: enabling power on all ports hub 2-1:1.0: port 3, status 0301, change 0001, 1.5 Mb/s hub 2-1:1.0: debounce: port 3: total 100ms stable 100ms status 0x301 ehci_hcd: block sizes: qh 128 qtd 96 itd 192 sitd 96 ACPI: PCI interrupt 0000:00:1d.7[D] -> GSI 10 (level, low) -> IRQ 10 ehci_hcd 0000:00:1d.7: Intel Corp. 82801DB (ICH4) USB2 EHCI Controller ehci_hcd 0000:00:1d.7: reset hcs_params 0x103206 dbg=1 cc=3 pcc=2 ordered !ppc ports=6 ehci_hcd 0000:00:1d.7: reset hcc_params 6871 thresh 7 uframes 1024 64 bit addr ehci_hcd 0000:00:1d.7: capability 0001 at 68 PCI: Setting latency timer of device 0000:00:1d.7 to 64 ehci_hcd 0000:00:1d.7: irq 10, pci mem e18c6000 ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 4 ehci_hcd 0000:00:1d.7: reset command 080002 (park)=0 ithresh=8 period=1024 Reset HALT PCI: cache line size of 32 is not supported by device 0000:00:1d.7 ehci_hcd 0000:00:1d.7: init command 010001 (park)=0 ithresh=1 period=1024 RUN ehci_hcd 0000:00:1d.7: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10 ehci_hcd 0000:00:1d.7: supports USB remote wakeup usb usb4: new device strings: Mfr=3, Product=2, SerialNumber=1 usb usb4: default language 0x0409 usb usb4: Product: Intel Corp. 82801DB (ICH4) USB2 EHCI Controller usb usb4: Manufacturer: Linux 2.6.7-mm1 ehci_hcd usb usb4: SerialNumber: 0000:00:1d.7 usb usb4: hotplug usb usb4: adding 4-0:1.0 (config #1, interface 0) usb 4-0:1.0: hotplug hub 4-0:1.0: usb_probe_interface hub 4-0:1.0: usb_probe_interface - got id hub 4-0:1.0: USB hub found hub 4-0:1.0: 6 ports detected hub 4-0:1.0: standalone hub hub 4-0:1.0: ganged power switching hub 4-0:1.0: individual port over-current protection hub 4-0:1.0: Single TT hub 4-0:1.0: TT requires at most 8 FS bit times hub 4-0:1.0: power on to power good time: 20ms hub 4-0:1.0: local power source is good hub 4-0:1.0: enabling power on all ports uhci_hcd 0000:00:1d.0: suspend_hc uhci_hcd 0000:00:1d.1: uhci_result_control: failed with status 440000 [df057270] link (1f0571e2) element (1f38b080) 0: [df38b080] link (1f38b0c0) e0 Stalled CRC/Timeo Length=7 MaxLen=7 DT0 EndPt=0 Dev=2, PID=2d(SETUP) (buf=1f3315c0) 1: [df38b0c0] link (1f38b100) e3 SPD Active Length=0 MaxLen=3 DT1 EndPt=0 Dev=2, PID=69(IN) (buf=1f3311a0) 2: [df38b100] link (00000001) e3 IOC Active Length=0 MaxLen=7ff DT1 EndPt=0 Dev=2, PID=e1(OUT) (buf=00000000) hub 2-1:1.0: hub_port_status failed (err = -71) hub 2-1:1.0: port 3 not enabled, trying reset again... uhci_hcd 0000:00:1d.1: uhci_result_control: failed with status 440000 [df057270] link (1f0571e2) element (1f38b080) 0: [df38b080] link (1f38b0c0) e0 Stalled CRC/Timeo Length=7 MaxLen=7 DT0 EndPt=0 Dev=2, PID=2d(SETUP) (buf=1f3315c0) 1: [df38b0c0] link (00000001) e3 IOC Active Length=0 MaxLen=7ff DT1 EndPt=0 Dev=2, PID=69(IN) (buf=00000000) hub 2-1:1.0: cannot reset port 3 (err = -71) hub 2-1:1.0: port 3 not enabled, trying reset again... uhci_hcd 0000:00:1d.1: uhci_result_control: failed with status 440000 [df0572a0] link (1f0571e2) element (1f38b100) 0: [df38b100] link (1f38b140) e0 Stalled CRC/Timeo Length=7 MaxLen=7 DT0 EndPt=0 Dev=2, PID=2d(SETUP) (buf=1f3315c0) 1: [df38b140] link (00000001) e3 IOC Active Length=0 MaxLen=7ff DT1 EndPt=0 Dev=2, PID=69(IN) (buf=00000000) hub 2-1:1.0: cannot reset port 3 (err = -71) hub 2-1:1.0: port 3 not enabled, trying reset again... uhci_hcd 0000:00:1d.1: uhci_result_control: failed with status 440000 [df057270] link (1f0571e2) element (1f38b080) 0: [df38b080] link (1f38b0c0) e0 Stalled CRC/Timeo Length=7 MaxLen=7 DT0 EndPt=0 Dev=2, PID=2d(SETUP) (buf=1f3315c0) 1: [df38b0c0] link (00000001) e3 IOC Active Length=0 MaxLen=7ff DT1 EndPt=0 Dev=2, PID=69(IN) (buf=00000000) hub 2-1:1.0: cannot reset port 3 (err = -71) hub 2-1:1.0: port 3 not enabled, trying reset again... uhci_hcd 0000:00:1d.1: uhci_result_control: failed with status 440000 [df0572a0] link (1f0571e2) element (1f38b100) 0: [df38b100] link (1f38b140) e0 Stalled CRC/Timeo Length=7 MaxLen=7 DT0 EndPt=0 Dev=2, PID=2d(SETUP) (buf=1f3315c0) 1: [df38b140] link (00000001) e3 IOC Active Length=0 MaxLen=7ff DT1 EndPt=0 Dev=2, PID=69(IN) (buf=00000000) hub 2-1:1.0: cannot reset port 3 (err = -71) hub 2-1:1.0: port 3 not enabled, trying reset again... hub 2-1:1.0: Cannot enable port 3. Maybe the USB cable is bad? uhci_hcd 0000:00:1d.1: uhci_result_control: failed with status 440000 [df057270] link (1f0571e2) element (1f38b080) 0: [df38b080] link (1f38b0c0) e0 Stalled CRC/Timeo Length=7 MaxLen=7 DT0 EndPt=0 Dev=2, PID=2d(SETUP) (buf=1f3315c0) 1: [df38b0c0] link (00000001) e3 IOC Active Length=0 MaxLen=7ff DT1 EndPt=0 Dev=2, PID=69(IN) (buf=00000000) hub 2-1:1.0: cannot disable port 3 (err = -71) uhci_hcd 0000:00:1d.1: uhci_result_control: failed with status 440000 [df0572a0] link (1f0571e2) element (1f38b100) 0: [df38b100] link (1f38b140) e0 Stalled CRC/Timeo Length=7 MaxLen=7 DT0 EndPt=0 Dev=2, PID=2d(SETUP) (buf=1f3315c0) 1: [df38b140] link (00000001) e3 IOC Active Length=0 MaxLen=7ff DT1 EndPt=0 Dev=2, PID=69(IN) (buf=00000000) hub 2-1:1.0: cannot reset port 3 (err = -71) hub 2-1:1.0: port 3 not enabled, trying reset again... uhci_hcd 0000:00:1d.1: uhci_result_control: failed with status 440000 [df057270] link (1f0571e2) element (1f38b080) 0: [df38b080] link (1f38b0c0) e0 Stalled CRC/Timeo Length=7 MaxLen=7 DT0 EndPt=0 Dev=2, PID=2d(SETUP) (buf=1f3315c0) 1: [df38b0c0] link (00000001) e3 IOC Active Length=0 MaxLen=7ff DT1 EndPt=0 Dev=2, PID=69(IN) (buf=00000000) hub 2-1:1.0: cannot reset port 3 (err = -71) hub 2-1:1.0: port 3 not enabled, trying reset again... uhci_hcd 0000:00:1d.1: uhci_result_control: failed with status 440000 [df0572a0] link (1f0571e2) element (1f38b100) 0: [df38b100] link (1f38b140) e0 Stalled CRC/Timeo Length=7 MaxLen=7 DT0 EndPt=0 Dev=2, PID=2d(SETUP) (buf=1f3315c0) 1: [df38b140] link (00000001) e3 IOC Active Length=0 MaxLen=7ff DT1 EndPt=0 Dev=2, PID=69(IN) (buf=00000000) hub 2-1:1.0: cannot reset port 3 (err = -71) hub 2-1:1.0: port 3 not enabled, trying reset again... uhci_hcd 0000:00:1d.1: uhci_result_control: failed with status 440000 [df057270] link (1f0571e2) element (1f38b080) 0: [df38b080] link (1f38b0c0) e0 Stalled CRC/Timeo Length=7 MaxLen=7 DT0 EndPt=0 Dev=2, PID=2d(SETUP) (buf=1f3315c0) 1: [df38b0c0] link (00000001) e3 IOC Active Length=0 MaxLen=7ff DT1 EndPt=0 Dev=2, PID=69(IN) (buf=00000000) hub 2-1:1.0: cannot reset port 3 (err = -71) hub 2-1:1.0: port 3 not enabled, trying reset again... uhci_hcd 0000:00:1d.1: uhci_result_control: failed with status 440000 [df0572a0] link (1f0571e2) element (1f38b100) 0: [df38b100] link (1f38b140) e0 Stalled CRC/Timeo Length=7 MaxLen=7 DT0 EndPt=0 Dev=2, PID=2d(SETUP) (buf=1f3315c0) 1: [df38b140] link (00000001) e3 IOC Active Length=0 MaxLen=7ff DT1 EndPt=0 Dev=2, PID=69(IN) (buf=00000000) hub 2-1:1.0: cannot reset port 3 (err = -71) hub 2-1:1.0: port 3 not enabled, trying reset again... hub 2-1:1.0: Cannot enable port 3. Maybe the USB cable is bad? uhci_hcd 0000:00:1d.1: uhci_result_control: failed with status 440000 [df057270] link (1f0571e2) element (1f38b080) 0: [df38b080] link (1f38b0c0) e0 Stalled CRC/Timeo Length=7 MaxLen=7 DT0 EndPt=0 Dev=2, PID=2d(SETUP) (buf=1f3315c0) 1: [df38b0c0] link (00000001) e3 IOC Active Length=0 MaxLen=7ff DT1 EndPt=0 Dev=2, PID=69(IN) (buf=00000000) hub 2-1:1.0: cannot disable port 3 (err = -71) uhci_hcd 0000:00:1d.1: uhci_result_control: failed with status 440000 [df0572a0] link (1f0571e2) element (1f38b100) 0: [df38b100] link (1f38b140) e0 Stalled CRC/Timeo Length=7 MaxLen=7 DT0 EndPt=0 Dev=2, PID=2d(SETUP) (buf=1f3315c0) 1: [df38b140] link (00000001) e3 IOC Active Length=0 MaxLen=7ff DT1 EndPt=0 Dev=2, PID=69(IN) (buf=00000000) hub 2-1:1.0: cannot disable port 3 (err = -71) uhci_hcd 0000:00:1d.1: uhci_result_control: failed with status 440000 [df057270] link (1f0571e2) element (1f38b080) 0: [df38b080] link (1f38b0c0) e0 Stalled CRC/Timeo Length=7 MaxLen=7 DT0 EndPt=0 Dev=2, PID=2d(SETUP) (buf=1f3315c0) 1: [df38b0c0] link (1f38b180) e3 SPD Active Length=0 MaxLen=3 DT1 EndPt=0 Dev=2, PID=69(IN) (buf=1f3311a0) 2: [df38b180] link (00000001) e3 IOC Active Length=0 MaxLen=7ff DT1 EndPt=0 Dev=2, PID=e1(OUT) (buf=00000000) hub 2-1:1.0: hub_port_status failed (err = -71) uhci_hcd 0000:00:1d.1: port 1 portsc 008a hub 2-0:1.0: port 1, status 0100, change 0003, 12 Mb/s usb 2-1: USB disconnect, address 2 usb 2-1: usb_disable_device nuking all URBs uhci_hcd 0000:00:1d.1: shutdown urb dfd43b80 pipe 40408280 ep1in-intr usb 2-1: unregistering interface 2-1:1.0 usb 2-1:1.0: hotplug usb 2-1: unregistering device usb 2-1: hotplug hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x100 ehci_hcd 0000:00:1d.7: GetStatus port 3 status 001803 POWER sig=j CSC CONNECT hub 4-0:1.0: port 3, status 0501, change 0001, 480 Mb/s uhci_hcd 0000:00:1d.2: suspend_hc hub 4-0:1.0: debounce: port 3: total 100ms stable 100ms status 0x501 hub 4-0:1.0: port 3 not reset yet, waiting 50ms ehci_hcd 0000:00:1d.7: port 3 high speed ehci_hcd 0000:00:1d.7: GetStatus port 3 status 001005 POWER sig=se0 PE CONNECT usb 4-3: new high speed USB device using address 2 usb 4-3: new device strings: Mfr=0, Product=0, SerialNumber=0 usb 4-3: hotplug usb 4-3: adding 4-3:1.0 (config #1, interface 0) usb 4-3:1.0: hotplug hub 4-3:1.0: usb_probe_interface hub 4-3:1.0: usb_probe_interface - got id hub 4-3:1.0: USB hub found hub 4-3:1.0: 4 ports detected hub 4-3:1.0: standalone hub hub 4-3:1.0: individual port power switching hub 4-3:1.0: individual port over-current protection hub 4-3:1.0: TT per port hub 4-3:1.0: TT requires at most 8 FS bit times hub 4-3:1.0: Port indicators are supported hub 4-3:1.0: power on to power good time: 100ms hub 4-3:1.0: local power source is good drivers/usb/host/ehci-sched.c: scheduled qh df517100 usecs 7/0 period 256.0 starting 255.0 (gap 0) hub 4-3:1.0: enabling power on all ports hub 4-3:1.0: port 3, status 0301, change 0001, 1.5 Mb/s uhci_hcd 0000:00:1d.1: suspend_hc ACPI: PCI interrupt 0000:00:1f.5[B] -> GSI 10 (level, low) -> IRQ 10 PCI: Setting latency timer of device 0000:00:1f.5 to 64 hub 4-3:1.0: debounce: port 3: total 100ms stable 100ms status 0x301 usb 4-3.3: new low speed USB device using address 3 usb 4-3.3: skipped 1 descriptor after interface usb 4-3.3: new device strings: Mfr=1, Product=2, SerialNumber=0 usb 4-3.3: default language 0x0409 usb 4-3.3: Product: Microsoft IntelliMouse® Explorer usb 4-3.3: Manufacturer: Microsoft usb 4-3.3: hotplug usb 4-3.3: adding 4-3.3:1.0 (config #1, interface 0) usb 4-3.3:1.0: hotplug usbcore: registered new driver hiddev usbhid 4-3.3:1.0: usb_probe_interface usbhid 4-3.3:1.0: usb_probe_interface - got id input: USB HID v1.00 Mouse [Microsoft Microsoft IntelliMouse® Explorer] on usb-0000:00:1d.7-3.3 usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.0:USB HID core driver intel8x0_measure_ac97_clock: measured 98438 usecs intel8x0: measured clock 24208 rejected intel8x0: clocking to 48000 ACPI: PCI interrupt 0000:00:1f.6[B] -> GSI 10 (level, low) -> IRQ 10 PCI: Setting latency timer of device 0000:00:1f.6 to 64 e1000: Ignoring new-style parameters in presence of obsolete ones Intel(R) PRO/1000 Network Driver - version 5.2.52-k4 Copyright (c) 1999-2004 Intel Corporation. ACPI: PCI interrupt 0000:02:01.0[A] -> GSI 9 (level, low) -> IRQ 9 e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection ath_hal: module license 'Proprietary' taints kernel. ath_hal: 0.9.9.3 wlan: 0.7.3.2 BETA ath_pci: no version for "ieee80211_encap" found: kernel tainted. ath_pci: 0.8.6.1 BETA ath_pci: 0.8.6.1 BETA ACPI: PCI interrupt 0000:02:02.0[A] -> GSI 11 (level, low) -> IRQ 11 ath%d: HAL ABI msmatch; driver expects 0x4050400, HAL reports 0x4030601 ACPI: Battery Slot [BAT0] (battery present) ACPI: AC Adapter [AC] (on-line) ACPI: Power Button (FF) [PWRF] ACPI: Lid Switch [LID] ACPI: Sleep Button (CM) [SLPB] ACPI: Processor [CPU] (supports C1 C2 C3, 8 throttling states) ACPI: Thermal Zone [THM0] (49 C) cs: IO port probe 0x0100-0x04ff: clean. cs: IO port probe 0x0800-0x08ff: clean. cs: IO port probe 0x0c00-0x0cff: clean. cs: IO port probe 0x0a00-0x0aff: clean. agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0. agpgart: Putting AGP V2 device at 0000:00:00.0 into 2x mode agpgart: Putting AGP V2 device at 0000:01:00.0 into 2x mode [drm] Loading R200 Microcode drivers/usb/host/ehci-sched.c: scheduled qh df517200 usecs 8/15 period 8.0 starting 6.0 (gap 1) drivers/usb/host/ehci-sched.c: descheduled qh df517200, period = 8 frame = 1030 count = 2, urbs = 1 drivers/usb/host/ehci-sched.c: reused previous qh df517200 schedule drivers/usb/host/ehci-sched.c: scheduled qh df517200 usecs 8/15 period 8.0 starting 6.0 (gap 1) [-- Attachment #3: dmesg-2.6.7-mm2 --] [-- Type: text/plain, Size: 21904 bytes --] Linux version 2.6.7-mm2 (root@t40) (gcc version 3.3.4 (Debian)) #2 Fri Jun 25 03:58:34 CEST 2004 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009f000 (usable) BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved) BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000001ff60000 (usable) BIOS-e820: 000000001ff60000 - 000000001ff77000 (ACPI data) BIOS-e820: 000000001ff77000 - 000000001ff79000 (ACPI NVS) BIOS-e820: 000000001ff80000 - 0000000020000000 (reserved) BIOS-e820: 00000000ff800000 - 0000000100000000 (reserved) 511MB LOWMEM available. On node 0 totalpages: 130912 DMA zone: 4096 pages, LIFO batch:1 Normal zone: 126816 pages, LIFO batch:16 HighMem zone: 0 pages, LIFO batch:1 DMI present. ACPI: RSDP (v002 IBM ) @ 0x000f6e00 ACPI: XSDT (v001 IBM TP-1R 0x00003051 LTP 0x00000000) @ 0x1ff6af83 ACPI: FADT (v003 IBM TP-1R 0x00003051 IBM 0x00000001) @ 0x1ff6b000 ACPI: SSDT (v001 IBM TP-1R 0x00003051 MSFT 0x0100000e) @ 0x1ff6b1b4 ACPI: ECDT (v001 IBM TP-1R 0x00003051 IBM 0x00000001) @ 0x1ff76e06 ACPI: TCPA (v001 IBM TP-1R 0x00003051 PTL 0x00000001) @ 0x1ff76e58 ACPI: BOOT (v001 IBM TP-1R 0x00003051 LTP 0x00000001) @ 0x1ff76fd8 ACPI: DSDT (v001 IBM TP-1R 0x00003051 MSFT 0x0100000e) @ 0x00000000 Built 1 zonelists Local APIC disabled by BIOS -- reenabling. Found and enabled local APIC! Initializing CPU#0 Kernel command line: BOOT_IMAGE=Linux2.6.7-mm2 ro root=306 quiet CPU 0 irqstacks, hard=c0504000 soft=c0503000 PID hash table entries: 2048 (order 11: 16384 bytes) Detected 1595.030 MHz processor. Using tsc for high-res timesource Console: colour VGA+ 80x25 Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 512552k/523648k available (2726k kernel code, 10328k reserved, 1193k data, 176k init, 0k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay loop... 3153.92 BogoMIPS Mount-cache hash table entries: 512 (order: 0, 4096 bytes) CPU: After generic identify, caps: a7e9fbbf 00000000 00000000 00000000 CPU: After vendor identify, caps: a7e9fbbf 00000000 00000000 00000000 CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 1024K CPU: After all inits, caps: a7e9fbbf 00000000 00000000 00000040 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. CPU: Intel(R) Pentium(R) M processor 1600MHz stepping 05 Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Checking 'hlt' instruction... OK. enabled ExtINT on CPU#0 ESR value before enabling vector: 00000000 ESR value after enabling vector: 00000000 Using local APIC timer interrupts. calibrating APIC timer ... ..... CPU clock speed is 1594.0510 MHz. ..... host bus clock speed is 99.0656 MHz. NET: Registered protocol family 16 PCI: PCI BIOS revision 2.10 entry at 0xfd8d6, last bus=8 PCI: Using configuration type 1 mtrr: v2.0 (20020519) ACPI: Subsystem revision 20040615 ACPI-0291: *** Info: Table [DSDT] replaced by host OS ACPI: IRQ9 SCI: Level Trigger. ACPI: Found ECDT ACPI: Interpreter enabled ACPI: Using PIC for interrupt routing ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *9 10 11) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 *10 11) ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 *11) ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 *10 11) ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 *10 11) ACPI: PCI Root Bridge [PCI0] (00:00) PCI: Probing PCI hardware (bus 00) PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1 PCI: Transparent bridge - 0000:00:1e.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: Embedded Controller [EC] (gpe 28) ACPI: Power Resource [PUBS] (on) ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT] Linux Plug and Play Support v0.97 (c) Adam Belay PnPBIOS: Scanning system for PnP BIOS support... PnPBIOS: Found PnP BIOS installation structure at 0xc00f6e30 PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0xb699, dseg 0x400 pnp: 00:0b: ioport range 0x4d0-0x4d1 has been reserved pnp: 00:0b: ioport range 0x1000-0x105f has been reserved pnp: 00:0b: ioport range 0x1060-0x107f has been reserved pnp: 00:0b: ioport range 0x1180-0x11bf has been reserved PnPBIOS: 19 nodes reported by PnP BIOS; 19 recorded by driver SCSI subsystem initialized Linux Kernel Card Services options: [pci] [cardbus] [pm] PCI: Using ACPI for IRQ routing ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 9 ACPI: PCI interrupt 0000:00:1d.0[A] -> GSI 9 (level, low) -> IRQ 9 ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 10 ACPI: PCI interrupt 0000:00:1d.1[B] -> GSI 10 (level, low) -> IRQ 10 ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11 ACPI: PCI interrupt 0000:00:1d.2[C] -> GSI 11 (level, low) -> IRQ 11 ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 10 ACPI: PCI interrupt 0000:00:1d.7[D] -> GSI 10 (level, low) -> IRQ 10 ACPI: PCI interrupt 0000:00:1f.1[A] -> GSI 11 (level, low) -> IRQ 11 ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10 ACPI: PCI interrupt 0000:00:1f.3[B] -> GSI 10 (level, low) -> IRQ 10 ACPI: PCI interrupt 0000:00:1f.5[B] -> GSI 10 (level, low) -> IRQ 10 ACPI: PCI interrupt 0000:00:1f.6[B] -> GSI 10 (level, low) -> IRQ 10 ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 9 (level, low) -> IRQ 9 ACPI: PCI interrupt 0000:02:00.0[A] -> GSI 9 (level, low) -> IRQ 9 ACPI: PCI interrupt 0000:02:00.1[B] -> GSI 10 (level, low) -> IRQ 10 ACPI: PCI interrupt 0000:02:01.0[A] -> GSI 9 (level, low) -> IRQ 9 ACPI: PCI interrupt 0000:02:02.0[A] -> GSI 11 (level, low) -> IRQ 11 NET: Registered protocol family 23 Bluetooth: Core ver 2.5 NET: Registered protocol family 31 Bluetooth: HCI device and connection manager initialized Bluetooth: HCI socket layer initialized ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 9 (level, low) -> IRQ 9 radeonfb: Retreived PLL infos from BIOS radeonfb: Reference=27.00 MHz (RefDiv=12) Memory=252.00 Mhz, System=200.00 MHz Non-DDC laptop panel detected radeonfb: Monitor 1 type LCD found radeonfb: Monitor 2 type no found radeonfb: panel ID string: SXGA+ Single (85MHz) radeonfb: detected LVDS panel size from BIOS: 1400x1050 radeondb: BIOS provided dividers will be used radeonfb: Power Management enabled for Mobility chipsets radeonfb: ATI Radeon Lf DDR SGRAM 64 MB Simple Boot Flag at 0x35 set to 0x1 Machine check exception polling timer started. IBM machine detected. Enabling interrupts during APM calls. apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac) apm: overridden by ACPI. udf: registering filesystem Initializing Cryptographic API isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found Console: switching to colour frame buffer device 175x65 lp: driver loaded but no devices found Real Time Clock Driver v1.12 Non-volatile memory driver v1.2 Linux agpgart interface v0.100 (c) Dave Jones agpgart: Detected an Intel 855PM Chipset. agpgart: Maximum main memory to use for agp memory: 439M agpgart: AGP aperture is 256M @ 0xd0000000 [drm] Initialized radeon 1.11.0 20020828 on minor 0: ATI Technologies Inc Radeon R250 Lf [Radeon Mobility 9000 M9] Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing enabled ttyS1 at I/O 0x2f8 (irq = 3) is a NS16550A ACPI: PCI interrupt 0000:00:1f.6[B] -> GSI 10 (level, low) -> IRQ 10 pnp: Device 00:12 activated. ttyS0 at I/O 0x3f8 (irq = 4) is a NS16550A parport: PnPBIOS parport detected. parport0: PC-style at 0x3bc (0x7bc), irq 7, dma 1 [PCSPP,TRISTATE,COMPAT,ECP,DMA] lp0: using parport0 (interrupt-driven). RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize loop: loaded (max 8 devices) PPP generic driver version 2.4.2 PPP Deflate Compression module registered PPP BSD Compression module registered NET: Registered protocol family 24 Universal TUN/TAP device driver 1.5 (C)1999-2002 Maxim Krasnyansky Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx ICH4: IDE controller at PCI slot 0000:00:1f.1 PCI: Enabling device 0000:00:1f.1 (0005 -> 0007) ACPI: PCI interrupt 0000:00:1f.1[A] -> GSI 11 (level, low) -> IRQ 11 ICH4: chipset revision 1 ICH4: not 100% native mode: will probe irqs later ide0: BM-DMA at 0x1860-0x1867, BIOS settings: hda:DMA, hdb:pio ide1: BM-DMA at 0x1868-0x186f, BIOS settings: hdc:DMA, hdd:pio hda: IC25N040ATCS05-0, ATA DISK drive Using anticipatory io scheduler ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 hdc: UJDA745 DVD/CDRW, ATAPI CD/DVD-ROM drive ide1 at 0x170-0x177,0x376 on irq 15 hda: max request size: 128KiB hda: 78140160 sectors (40007 MB) w/7898KiB Cache, CHS=65535/16/63, UDMA(100) hda: cache flushes supported hda: hda1 hda2 hda3 < hda5 hda6 hda7 > hda4 hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33) Uniform CD-ROM driver Revision: 3.20 ACPI: PCI interrupt 0000:02:00.0[A] -> GSI 9 (level, low) -> IRQ 9 Yenta: CardBus bridge found at 0000:02:00.0 [1014:0512] Yenta: Using INTVAL to route CSC interrupts to PCI Yenta: Routing CardBus interrupts to PCI Yenta TI: socket 0000:02:00.0, mfunc 0x01d21022, devctl 0x64 Yenta: ISA IRQ mask 0x0078, PCI irq 9 Socket status: 30000006 ACPI: PCI interrupt 0000:02:00.1[B] -> GSI 10 (level, low) -> IRQ 10 Yenta: CardBus bridge found at 0000:02:00.1 [1014:0512] Yenta: Using INTVAL to route CSC interrupts to PCI Yenta: Routing CardBus interrupts to PCI Yenta TI: socket 0000:02:00.1, mfunc 0x01d21022, devctl 0x64 Yenta: ISA IRQ mask 0x0078, PCI irq 10 Socket status: 30000006 serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 mice: PS/2 mouse device common for all mice input: AT Translated Set 2 keyboard on isa0060/serio0 Synaptics Touchpad, model: 1 Firmware: 5.9 Sensor: 44 new absolute packet format Touchpad has extended capability bits -> multifinger detection -> palm detection -> pass-through port input: SynPS/2 Synaptics TouchPad on isa0060/serio1 serio: Synaptics pass-through port at isa0060/serio1/input0 input: PS/2 Generic Mouse on synaptics-pt/serio0 input: PC Speaker Advanced Linux Sound Architecture Driver Version 1.0.5 (Sun May 30 10:49:40 2004 UTC). ALSA device list: No soundcards found. NET: Registered protocol family 2 IP: routing cache hash table of 4096 buckets, 32Kbytes TCP: Hash tables configured (established 32768 bind 65536) Initializing IPsec netlink socket NET: Registered protocol family 1 NET: Registered protocol family 10 IPv6 over IPv4 tunneling driver NET: Registered protocol family 17 IrCOMM protocol (Dag Brattli) Bluetooth: L2CAP ver 2.2 Bluetooth: L2CAP socket layer initialized Bluetooth: SCO (Voice Link) ver 0.3 Bluetooth: SCO socket layer initialized Bluetooth: RFCOMM ver 1.3 Bluetooth: RFCOMM socket layer initialized Bluetooth: RFCOMM TTY layer initialized Bluetooth: BNEP (Ethernet Emulation) ver 1.0 Bluetooth: BNEP filters: protocol multicast speedstep-centrino: found "Intel(R) Pentium(R) M processor 1600MHz": max frequency: 1600000kHz PM: Reading pmdisk image. PM: Resume from disk failed. ACPI: (supports S0 S3 S4 S5) kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) readonly. Freeing unused kernel memory: 176k freed Adding 498920k swap on /dev/hda5. Priority:-1 extents:1 EXT3 FS on hda6, internal journal kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 600 seconds EXT3 FS on hda4, internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 600 seconds EXT3 FS on hda7, internal journal EXT3-fs: mounted filesystem with ordered data mode. usbcore: registered new driver usbfs usbcore: registered new driver hub USB Universal Host Controller Interface driver v2.2 ACPI: PCI interrupt 0000:00:1d.0[A] -> GSI 9 (level, low) -> IRQ 9 uhci_hcd 0000:00:1d.0: Intel Corp. 82801DB (ICH4) USB UHCI #1 PCI: Setting latency timer of device 0000:00:1d.0 to 64 uhci_hcd 0000:00:1d.0: irq 9, io base 00001800 uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1 uhci_hcd 0000:00:1d.0: detected 2 ports usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: default language 0x0409 usb usb1: Product: Intel Corp. 82801DB (ICH4) USB UHCI #1 usb usb1: Manufacturer: Linux 2.6.7-mm2 uhci_hcd usb usb1: SerialNumber: 0000:00:1d.0 usb usb1: hotplug usb usb1: adding 1-0:1.0 (config #1, interface 0) usb 1-0:1.0: hotplug hub 1-0:1.0: usb_probe_interface hub 1-0:1.0: usb_probe_interface - got id hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected hub 1-0:1.0: standalone hub hub 1-0:1.0: no power switching (usb 1.0) hub 1-0:1.0: individual port over-current protection hub 1-0:1.0: power on to power good time: 2ms hub 1-0:1.0: local power source is good ACPI: PCI interrupt 0000:00:1d.1[B] -> GSI 10 (level, low) -> IRQ 10 uhci_hcd 0000:00:1d.1: Intel Corp. 82801DB (ICH4) USB UHCI #2 PCI: Setting latency timer of device 0000:00:1d.1 to 64 uhci_hcd 0000:00:1d.1: irq 10, io base 00001820 uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2 uhci_hcd 0000:00:1d.1: detected 2 ports usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1 usb usb2: default language 0x0409 usb usb2: Product: Intel Corp. 82801DB (ICH4) USB UHCI #2 usb usb2: Manufacturer: Linux 2.6.7-mm2 uhci_hcd usb usb2: SerialNumber: 0000:00:1d.1 usb usb2: hotplug usb usb2: adding 2-0:1.0 (config #1, interface 0) usb 2-0:1.0: hotplug hub 2-0:1.0: usb_probe_interface hub 2-0:1.0: usb_probe_interface - got id hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected hub 2-0:1.0: standalone hub hub 2-0:1.0: no power switching (usb 1.0) hub 2-0:1.0: individual port over-current protection hub 2-0:1.0: power on to power good time: 2ms hub 2-0:1.0: local power source is good ACPI: PCI interrupt 0000:00:1d.2[C] -> GSI 11 (level, low) -> IRQ 11 uhci_hcd 0000:00:1d.2: Intel Corp. 82801DB (ICH4) USB UHCI #3 PCI: Setting latency timer of device 0000:00:1d.2 to 64 uhci_hcd 0000:00:1d.2: irq 11, io base 00001840 uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3 uhci_hcd 0000:00:1d.2: detected 2 ports usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1 usb usb3: default language 0x0409 usb usb3: Product: Intel Corp. 82801DB (ICH4) USB UHCI #3 usb usb3: Manufacturer: Linux 2.6.7-mm2 uhci_hcd usb usb3: SerialNumber: 0000:00:1d.2 usb usb3: hotplug usb usb3: adding 3-0:1.0 (config #1, interface 0) usb 3-0:1.0: hotplug hub 3-0:1.0: usb_probe_interface hub 3-0:1.0: usb_probe_interface - got id hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected hub 3-0:1.0: standalone hub hub 3-0:1.0: no power switching (usb 1.0) hub 3-0:1.0: individual port over-current protection hub 3-0:1.0: power on to power good time: 2ms hub 3-0:1.0: local power source is good uhci_hcd 0000:00:1d.1: port 1 portsc 0093 hub 2-0:1.0: port 1, status 0101, change 0001, 12 Mb/s hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x101 usb 2-1: new full speed USB device using address 2 usb 2-1: new device strings: Mfr=0, Product=0, SerialNumber=0 usb 2-1: hotplug usb 2-1: adding 2-1:1.0 (config #1, interface 0) usb 2-1:1.0: hotplug hub 2-1:1.0: usb_probe_interface hub 2-1:1.0: usb_probe_interface - got id hub 2-1:1.0: USB hub found hub 2-1:1.0: 4 ports detected hub 2-1:1.0: standalone hub hub 2-1:1.0: individual port power switching hub 2-1:1.0: individual port over-current protection hub 2-1:1.0: Port indicators are supported hub 2-1:1.0: power on to power good time: 100ms hub 2-1:1.0: local power source is good hub 2-1:1.0: enabling power on all ports ehci_hcd: block sizes: qh 128 qtd 96 itd 192 sitd 96 ACPI: PCI interrupt 0000:00:1d.7[D] -> GSI 10 (level, low) -> IRQ 10 ehci_hcd 0000:00:1d.7: Intel Corp. 82801DB (ICH4) USB2 EHCI Controller ehci_hcd 0000:00:1d.7: reset hcs_params 0x103206 dbg=1 cc=3 pcc=2 ordered !ppc ports=6 ehci_hcd 0000:00:1d.7: reset hcc_params 6871 thresh 7 uframes 1024 64 bit addr ehci_hcd 0000:00:1d.7: capability 0001 at 68 PCI: Setting latency timer of device 0000:00:1d.7 to 64 ehci_hcd 0000:00:1d.7: irq 10, pci mem e18a5000 ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 4 ehci_hcd 0000:00:1d.7: reset command 080002 (park)=0 ithresh=8 period=1024 Reset HALT PCI: cache line size of 32 is not supported by device 0000:00:1d.7 ehci_hcd 0000:00:1d.7: init command 010001 (park)=0 ithresh=1 period=1024 RUN ehci_hcd 0000:00:1d.7: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10 ehci_hcd 0000:00:1d.7: supports USB remote wakeup usb usb4: new device strings: Mfr=3, Product=2, SerialNumber=1 usb usb4: default language 0x0409 usb usb4: Product: Intel Corp. 82801DB (ICH4) USB2 EHCI Controller usb usb4: Manufacturer: Linux 2.6.7-mm2 ehci_hcd usb usb4: SerialNumber: 0000:00:1d.7 usb usb4: hotplug uhci_hcd 0000:00:1d.1: port 1 portsc 008a hub 2-0:1.0: port 1, status 0100, change 0003, 12 Mb/s usb 2-1: USB disconnect, address 2 usb 2-1: usb_disable_device nuking all URBs uhci_hcd 0000:00:1d.1: shutdown urb dfd45280 pipe 40408280 ep1in-intr usb usb4: adding 4-0:1.0 (config #1, interface 0) usb 4-0:1.0: hotplug usb 2-1: unregistering interface 2-1:1.0 usb 2-1:1.0: hotplug usb 2-1: unregistering device usb 2-1: hotplug hub 4-0:1.0: usb_probe_interface hub 4-0:1.0: usb_probe_interface - got id hub 4-0:1.0: USB hub found hub 4-0:1.0: 6 ports detected hub 4-0:1.0: standalone hub hub 4-0:1.0: ganged power switching hub 4-0:1.0: individual port over-current protection hub 4-0:1.0: Single TT hub 4-0:1.0: TT requires at most 8 FS bit times hub 4-0:1.0: power on to power good time: 20ms hub 4-0:1.0: local power source is good hub 4-0:1.0: enabling power on all ports hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x100 ACPI: PCI interrupt 0000:00:1f.5[B] -> GSI 10 (level, low) -> IRQ 10 PCI: Setting latency timer of device 0000:00:1f.5 to 64 ehci_hcd 0000:00:1d.7: GetStatus port 3 status 001803 POWER sig=j CSC CONNECT hub 4-0:1.0: port 3, status 0501, change 0001, 480 Mb/s hub 4-0:1.0: debounce: port 3: total 100ms stable 100ms status 0x501 hub 4-0:1.0: port 3 not reset yet, waiting 50ms ehci_hcd 0000:00:1d.7: port 3 high speed ehci_hcd 0000:00:1d.7: GetStatus port 3 status 001005 POWER sig=se0 PE CONNECT usb 4-3: new high speed USB device using address 2 usb 4-3: new device strings: Mfr=0, Product=0, SerialNumber=0 usb 4-3: hotplug usb 4-3: adding 4-3:1.0 (config #1, interface 0) usb 4-3:1.0: hotplug hub 4-3:1.0: usb_probe_interface hub 4-3:1.0: usb_probe_interface - got id hub 4-3:1.0: USB hub found hub 4-3:1.0: 4 ports detected hub 4-3:1.0: standalone hub hub 4-3:1.0: individual port power switching hub 4-3:1.0: individual port over-current protection hub 4-3:1.0: TT per port hub 4-3:1.0: TT requires at most 8 FS bit times hub 4-3:1.0: Port indicators are supported hub 4-3:1.0: power on to power good time: 100ms hub 4-3:1.0: local power source is good drivers/usb/host/ehci-sched.c: scheduled qh df381100 usecs 7/0 period 256.0 starting 255.0 (gap 0) hub 4-3:1.0: enabling power on all ports hub 4-3:1.0: port 3, status 0301, change 0001, 1.5 Mb/s uhci_hcd 0000:00:1d.0: suspend_hc hub 4-3:1.0: debounce: port 3: total 100ms stable 100ms status 0x301 uhci_hcd 0000:00:1d.1: suspend_hc usb 4-3.3: new low speed USB device using address 3 usb 4-3.3: skipped 1 descriptor after interface usb 4-3.3: new device strings: Mfr=1, Product=2, SerialNumber=0 usb 4-3.3: default language 0x0409 usb 4-3.3: Product: Microsoft IntelliMouse® Explorer usb 4-3.3: Manufacturer: Microsoft usb 4-3.3: hotplug usb 4-3.3: adding 4-3.3:1.0 (config #1, interface 0) usb 4-3.3:1.0: hotplug uhci_hcd 0000:00:1d.2: suspend_hc intel8x0_measure_ac97_clock: measured 79374 usecs intel8x0: clocking to 48000 usbcore: registered new driver hiddev usbhid 4-3.3:1.0: usb_probe_interface usbhid 4-3.3:1.0: usb_probe_interface - got id input: USB HID v1.00 Mouse [Microsoft Microsoft IntelliMouse® Explorer] on usb-0000:00:1d.7-3.3 usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.0:USB HID core driver ACPI: PCI interrupt 0000:00:1f.6[B] -> GSI 10 (level, low) -> IRQ 10 PCI: Setting latency timer of device 0000:00:1f.6 to 64 e1000: Ignoring new-style parameters in presence of obsolete ones Intel(R) PRO/1000 Network Driver - version 5.2.52-k4 Copyright (c) 1999-2004 Intel Corporation. ACPI: PCI interrupt 0000:02:01.0[A] -> GSI 9 (level, low) -> IRQ 9 e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection ACPI: Battery Slot [BAT0] (battery present) ACPI: AC Adapter [AC] (on-line) ACPI: Power Button (FF) [PWRF] ACPI: Lid Switch [LID] ACPI: Sleep Button (CM) [SLPB] ACPI: Processor [CPU] (supports C1 C2 C3, 8 throttling states) ACPI: Thermal Zone [THM0] (49 C) cs: IO port probe 0x0100-0x04ff: clean. cs: IO port probe 0x0800-0x08ff: clean. cs: IO port probe 0x0c00-0x0cff: clean. cs: IO port probe 0x0a00-0x0aff: clean. agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0. agpgart: Putting AGP V2 device at 0000:00:00.0 into 2x mode agpgart: Putting AGP V2 device at 0000:01:00.0 into 2x mode [drm] Loading R200 Microcode drivers/usb/host/ehci-sched.c: scheduled qh df381200 usecs 8/15 period 8.0 starting 6.0 (gap 1) drivers/usb/host/ehci-sched.c: descheduled qh df381200, period = 8 frame = 1030 count = 2, urbs = 1 drivers/usb/host/ehci-sched.c: reused previous qh df381200 schedule drivers/usb/host/ehci-sched.c: scheduled qh df381200 usecs 8/15 period 8.0 starting 6.0 (gap 1) ^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: Linux 2.6.7-mm1, IBM T40p, ACPI C3 finally working. 2004-06-25 2:06 ` Linux 2.6.7-mm1, IBM T40p, ACPI C3 finally working Alexander Gran @ 2004-06-25 2:51 ` Adam Sulmicki 2004-06-25 14:05 ` Alexander Gran 0 siblings, 1 reply; 8+ messages in thread From: Adam Sulmicki @ 2004-06-25 2:51 UTC (permalink / raw) To: Alexander Gran; +Cc: linux-kernel, linux-thinkpad can you try to revert this sub-patch and see if it helps? ftp://ftp.kernel.org/pub/linux/kernel/people/akpm/patches/2.6/2.6.7/2.6.7-mm2/broken-out/bk-acpi.patch it would be really nice to have T40? working in 2.6.8 proper. On Fri, 25 Jun 2004, Alexander Gran wrote: > Ok guys, now this is strange. > > since 2.6.7-mm2 C3 does not work any longer. No idea why. > Same config, same system: > IBM t40p, 2373-g1g. > lspci -vvv: > root@t40:~# lspci -vvv > 0000:00:00.0 Host bridge: Intel Corp. 82855PM Processor to I/O Controller (rev > 03) > Subsystem: IBM: Unknown device 0529 > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR+ FastB2B- > Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort+ >SERR- <PERR- > Latency: 0 > Region 0: Memory at d0000000 (32-bit, prefetchable) > Capabilities: [e4] #09 [f104] > Capabilities: [a0] AGP version 2.0 > Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- > 64bit- FW+ AGP3- Rate=x1,x2,x4 > Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW- > Rate=x2 > > 0000:00:01.0 PCI bridge: Intel Corp. 82855PM Processor to AGP Controller (rev > 03) (prog-if 00 [Normal decode]) > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR+ FastB2B- > Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort- >SERR- <PERR- > Latency: 96 > Bus: primary=00, secondary=01, subordinate=01, sec-latency=64 > I/O behind bridge: 00003000-00003fff > Memory behind bridge: c0100000-c01fffff > Prefetchable memory behind bridge: e0000000-e7ffffff > Expansion ROM at 00003000 [disabled] [size=4K] > BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B- > > 0000:00:1d.0 USB Controller: Intel Corp. 82801DB (ICH4) USB UHCI #1 (rev 01) > (prog-if 00 [UHCI]) > Subsystem: IBM: Unknown device 052d > Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- > Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- > Latency: 0 > Interrupt: pin A routed to IRQ 9 > Region 4: I/O ports at 1800 [size=32] > > 0000:00:1d.1 USB Controller: Intel Corp. 82801DB (ICH4) USB UHCI #2 (rev 01) > (prog-if 00 [UHCI]) > Subsystem: IBM: Unknown device 052d > Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- > Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- > Latency: 0 > Interrupt: pin B routed to IRQ 10 > Region 4: I/O ports at 1820 [size=32] > > 0000:00:1d.2 USB Controller: Intel Corp. 82801DB (ICH4) USB UHCI #3 (rev 01) > (prog-if 00 [UHCI]) > Subsystem: IBM: Unknown device 052d > Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- > Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- > Latency: 0 > Interrupt: pin C routed to IRQ 11 > Region 4: I/O ports at 1840 [size=32] > > 0000:00:1d.7 USB Controller: Intel Corp. 82801DB (ICH4) USB2 EHCI Controller > (rev 01) (prog-if 20 [EHCI]) > Subsystem: IBM: Unknown device 052e > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR+ FastB2B- > Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- > Latency: 0 > Interrupt: pin D routed to IRQ 10 > Region 0: Memory at c0000000 (32-bit, non-prefetchable) > Capabilities: [50] Power Management version 2 > Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA > PME(D0+,D1-,D2-,D3hot+,D3cold+) > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > Capabilities: [58] #0a [2080] > > 0000:00:1e.0 PCI bridge: Intel Corp. 82801BAM/CAM PCI Bridge (rev 81) (prog-if > 00 [Normal decode]) > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR+ FastB2B- > Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort- >SERR- <PERR+ > Latency: 0 > Bus: primary=00, secondary=02, subordinate=08, sec-latency=168 > I/O behind bridge: 00004000-00008fff > Memory behind bridge: c0200000-cfffffff > Prefetchable memory behind bridge: e8000000-efffffff > BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B- > > 0000:00:1f.0 ISA bridge: Intel Corp. 82801DBM LPC Interface Controller (rev > 01) > Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- > Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- > Latency: 0 > > 0000:00:1f.1 IDE interface: Intel Corp. 82801DBM (ICH4) Ultra ATA Storage > Controller (rev 01) (prog-if 8a [Master SecP PriP]) > Subsystem: IBM: Unknown device 052d > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- > Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- > Latency: 0 > Interrupt: pin A routed to IRQ 11 > Region 0: I/O ports at <unassigned> > Region 1: I/O ports at <unassigned> > Region 2: I/O ports at <unassigned> > Region 3: I/O ports at <unassigned> > Region 4: I/O ports at 1860 [size=16] > Region 5: Memory at 20000000 (32-bit, non-prefetchable) [size=1K] > > 0000:00:1f.3 SMBus: Intel Corp. 82801DB/DBM (ICH4) SMBus Controller (rev 01) > Subsystem: IBM: Unknown device 052d > Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- > Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- > Interrupt: pin B routed to IRQ 10 > Region 4: I/O ports at 1880 [size=32] > > 0000:00:1f.5 Multimedia audio controller: Intel Corp. 82801DB (ICH4) AC'97 > Audio Controller (rev 01) > Subsystem: IBM: Unknown device 0537 > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- > Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- > Latency: 0 > Interrupt: pin B routed to IRQ 10 > Region 0: I/O ports at 1c00 > Region 1: I/O ports at 18c0 [size=64] > Region 2: Memory at c0000c00 (32-bit, non-prefetchable) [size=512] > Region 3: Memory at c0000800 (32-bit, non-prefetchable) [size=256] > Capabilities: [50] Power Management version 2 > Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA > PME(D0+,D1-,D2-,D3hot+,D3cold+) > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > > 0000:00:1f.6 Modem: Intel Corp. 82801DB (ICH4) AC'97 Modem Controller (rev 01) > (prog-if 00 [Generic]) > Subsystem: IBM: Unknown device 0525 > Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- > Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- > Latency: 0 > Interrupt: pin B routed to IRQ 10 > Region 0: I/O ports at 2400 > Region 1: I/O ports at 2000 [size=128] > Capabilities: [50] Power Management version 2 > Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA > PME(D0+,D1-,D2-,D3hot+,D3cold+) > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > > 0000:01:00.0 VGA compatible controller: ATI Technologies Inc Radeon R250 Lf > [Radeon Mobility 9000 M9] (rev 02) (prog-if 00 [VGA]) > Subsystem: IBM: Unknown device 054d > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping+ SERR+ FastB2B+ > Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- > Latency: 66 (2000ns min), Cache Line Size: 0x08 (32 bytes) > Interrupt: pin A routed to IRQ 9 > Region 0: Memory at e0000000 (32-bit, prefetchable) > Region 1: I/O ports at 3000 [size=256] > Region 2: Memory at c0100000 (32-bit, non-prefetchable) [size=64K] > Capabilities: [58] AGP version 2.0 > Status: RQ=48 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- > 64bit- FW+ AGP3- Rate=x1,x2,x4 > Command: RQ=32 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW- > Rate=x2 > Capabilities: [50] Power Management version 2 > Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA > PME(D0-,D1-,D2-,D3hot-,D3cold-) > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > > 0000:02:00.0 CardBus bridge: Texas Instruments PCI1520 PC card Cardbus > Controller (rev 01) > Subsystem: IBM ThinkPad T30/T40 > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- > Latency: 168, Cache Line Size: 0x20 (128 bytes) > Interrupt: pin A routed to IRQ 9 > Region 0: Memory at b0000000 (32-bit, non-prefetchable) > Bus: primary=02, secondary=03, subordinate=06, sec-latency=176 > Memory window 0: 20400000-207ff000 (prefetchable) > Memory window 1: 20800000-20bff000 > I/O window 0: 00004000-000040ff > I/O window 1: 00004400-000044ff > BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+ > 16-bit legacy interface ports at 0001 > > 0000:02:00.1 CardBus bridge: Texas Instruments PCI1520 PC card Cardbus > Controller (rev 01) > Subsystem: IBM ThinkPad T30/T40 > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- > Latency: 168, Cache Line Size: 0x20 (128 bytes) > Interrupt: pin B routed to IRQ 10 > Region 0: Memory at b1000000 (32-bit, non-prefetchable) > Bus: primary=02, secondary=07, subordinate=0a, sec-latency=176 > Memory window 0: 20c00000-20fff000 (prefetchable) > Memory window 1: 21000000-213ff000 > I/O window 0: 00004800-000048ff > I/O window 1: 00004c00-00004cff > BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+ > 16-bit legacy interface ports at 0001 > > 0000:02:01.0 Ethernet controller: Intel Corp. 82540EP Gigabit Ethernet > Controller (Mobile) (rev 03) > Subsystem: IBM PRO/1000 MT Mobile Connection > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- > Stepping- SERR+ FastB2B- > Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- > Latency: 64 (63750ns min), Cache Line Size: 0x08 (32 bytes) > Interrupt: pin A routed to IRQ 9 > Region 0: Memory at c0220000 (32-bit, non-prefetchable) > Region 1: Memory at c0200000 (32-bit, non-prefetchable) [size=64K] > Region 2: I/O ports at 8000 [size=64] > Capabilities: [dc] Power Management version 2 > Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA > PME(D0+,D1-,D2-,D3hot+,D3cold+) > Status: D0 PME-Enable- DSel=0 DScale=1 PME- > Capabilities: [f0] Message Signalled Interrupts: 64bit+ Queue=0/0 > Enable- > Address: 0000000000000000 Data: 0000 > > 0000:02:02.0 Ethernet controller: Atheros Communications, Inc. AR5211 802.11ab > NIC (rev 01) > Subsystem: Unknown device 17ab:8310 > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- > Stepping- SERR+ FastB2B- > Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- > Latency: 80 (2500ns min, 7000ns max), Cache Line Size: 0x08 (32 bytes) > Interrupt: pin A routed to IRQ 11 > Region 0: Memory at c0210000 (32-bit, non-prefetchable) > Capabilities: [44] Power Management version 2 > Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA > PME(D0-,D1-,D2-,D3hot-,D3cold-) > Status: D0 PME-Enable- DSel=0 DScale=2 PME- > > dmesges attached. > > regards > Alex > > > Am Montag, 21. Juni 2004 19:50 schrieb Alexander Gran: > > Hi, > > > > just a quick note: > > Since 2.6.7-mm1 acpi C3 works even with usb and radeon loaded. > > Great work! > > > > regards > > Alex > > ^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: Linux 2.6.7-mm1, IBM T40p, ACPI C3 finally working. 2004-06-25 2:51 ` Adam Sulmicki @ 2004-06-25 14:05 ` Alexander Gran 2004-06-25 17:30 ` Adam Sulmicki 0 siblings, 1 reply; 8+ messages in thread From: Alexander Gran @ 2004-06-25 14:05 UTC (permalink / raw) To: Adam Sulmicki; +Cc: linux-kernel, linux-thinkpad [-- Attachment #1: Type: text/plain, Size: 13934 bytes --] Sorry, did not help: alex@t40:/proc/acpi/processor/CPU$ cat power active state: C2 default state: C1 bus master activity: ffffffff states: C1: promotion[C2] demotion[--] latency[000] usage[00000010] *C2: promotion[C3] demotion[C1] latency[001] usage[00164425] C3: promotion[--] demotion[C2] latency[085] usage[00000000] regards Alex Am Freitag, 25. Juni 2004 04:51 schrieb Adam Sulmicki: > can you try to revert this sub-patch and see if it helps? > > ftp://ftp.kernel.org/pub/linux/kernel/people/akpm/patches/2.6/2.6.7/2.6.7-m >m2/broken-out/bk-acpi.patch > > it would be really nice to have T40? working in 2.6.8 proper. > > On Fri, 25 Jun 2004, Alexander Gran wrote: > > Ok guys, now this is strange. > > > > since 2.6.7-mm2 C3 does not work any longer. No idea why. > > Same config, same system: > > IBM t40p, 2373-g1g. > > lspci -vvv: > > root@t40:~# lspci -vvv > > 0000:00:00.0 Host bridge: Intel Corp. 82855PM Processor to I/O Controller > > (rev 03) > > Subsystem: IBM: Unknown device 0529 > > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- > > ParErr- Stepping- SERR+ FastB2B- > > Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- > > <TAbort- <MAbort+ >SERR- <PERR- > > Latency: 0 > > Region 0: Memory at d0000000 (32-bit, prefetchable) > > Capabilities: [e4] #09 [f104] > > Capabilities: [a0] AGP version 2.0 > > Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- > > HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4 > > Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW- > > Rate=x2 > > > > 0000:00:01.0 PCI bridge: Intel Corp. 82855PM Processor to AGP Controller > > (rev 03) (prog-if 00 [Normal decode]) > > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- > > ParErr- Stepping- SERR+ FastB2B- > > Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- > > <TAbort- <MAbort- >SERR- <PERR- > > Latency: 96 > > Bus: primary=00, secondary=01, subordinate=01, sec-latency=64 > > I/O behind bridge: 00003000-00003fff > > Memory behind bridge: c0100000-c01fffff > > Prefetchable memory behind bridge: e0000000-e7ffffff > > Expansion ROM at 00003000 [disabled] [size=4K] > > BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B- > > > > 0000:00:1d.0 USB Controller: Intel Corp. 82801DB (ICH4) USB UHCI #1 (rev > > 01) (prog-if 00 [UHCI]) > > Subsystem: IBM: Unknown device 052d > > Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- > > ParErr- Stepping- SERR- FastB2B- > > Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > > <TAbort- <MAbort- >SERR- <PERR- > > Latency: 0 > > Interrupt: pin A routed to IRQ 9 > > Region 4: I/O ports at 1800 [size=32] > > > > 0000:00:1d.1 USB Controller: Intel Corp. 82801DB (ICH4) USB UHCI #2 (rev > > 01) (prog-if 00 [UHCI]) > > Subsystem: IBM: Unknown device 052d > > Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- > > ParErr- Stepping- SERR- FastB2B- > > Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > > <TAbort- <MAbort- >SERR- <PERR- > > Latency: 0 > > Interrupt: pin B routed to IRQ 10 > > Region 4: I/O ports at 1820 [size=32] > > > > 0000:00:1d.2 USB Controller: Intel Corp. 82801DB (ICH4) USB UHCI #3 (rev > > 01) (prog-if 00 [UHCI]) > > Subsystem: IBM: Unknown device 052d > > Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- > > ParErr- Stepping- SERR- FastB2B- > > Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > > <TAbort- <MAbort- >SERR- <PERR- > > Latency: 0 > > Interrupt: pin C routed to IRQ 11 > > Region 4: I/O ports at 1840 [size=32] > > > > 0000:00:1d.7 USB Controller: Intel Corp. 82801DB (ICH4) USB2 EHCI > > Controller (rev 01) (prog-if 20 [EHCI]) > > Subsystem: IBM: Unknown device 052e > > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- > > ParErr- Stepping- SERR+ FastB2B- > > Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > > <TAbort- <MAbort- >SERR- <PERR- > > Latency: 0 > > Interrupt: pin D routed to IRQ 10 > > Region 0: Memory at c0000000 (32-bit, non-prefetchable) > > Capabilities: [50] Power Management version 2 > > Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA > > PME(D0+,D1-,D2-,D3hot+,D3cold+) > > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > > Capabilities: [58] #0a [2080] > > > > 0000:00:1e.0 PCI bridge: Intel Corp. 82801BAM/CAM PCI Bridge (rev 81) > > (prog-if 00 [Normal decode]) > > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- > > ParErr- Stepping- SERR+ FastB2B- > > Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- > > <TAbort- <MAbort- >SERR- <PERR+ > > Latency: 0 > > Bus: primary=00, secondary=02, subordinate=08, sec-latency=168 > > I/O behind bridge: 00004000-00008fff > > Memory behind bridge: c0200000-cfffffff > > Prefetchable memory behind bridge: e8000000-efffffff > > BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B- > > > > 0000:00:1f.0 ISA bridge: Intel Corp. 82801DBM LPC Interface Controller > > (rev 01) > > Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- > > ParErr- Stepping- SERR- FastB2B- > > Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > > <TAbort- <MAbort- >SERR- <PERR- > > Latency: 0 > > > > 0000:00:1f.1 IDE interface: Intel Corp. 82801DBM (ICH4) Ultra ATA Storage > > Controller (rev 01) (prog-if 8a [Master SecP PriP]) > > Subsystem: IBM: Unknown device 052d > > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- > > ParErr- Stepping- SERR- FastB2B- > > Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > > <TAbort- <MAbort- >SERR- <PERR- > > Latency: 0 > > Interrupt: pin A routed to IRQ 11 > > Region 0: I/O ports at <unassigned> > > Region 1: I/O ports at <unassigned> > > Region 2: I/O ports at <unassigned> > > Region 3: I/O ports at <unassigned> > > Region 4: I/O ports at 1860 [size=16] > > Region 5: Memory at 20000000 (32-bit, non-prefetchable) [size=1K] > > > > 0000:00:1f.3 SMBus: Intel Corp. 82801DB/DBM (ICH4) SMBus Controller (rev > > 01) Subsystem: IBM: Unknown device 052d > > Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- > > ParErr- Stepping- SERR- FastB2B- > > Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > > <TAbort- <MAbort- >SERR- <PERR- > > Interrupt: pin B routed to IRQ 10 > > Region 4: I/O ports at 1880 [size=32] > > > > 0000:00:1f.5 Multimedia audio controller: Intel Corp. 82801DB (ICH4) > > AC'97 Audio Controller (rev 01) > > Subsystem: IBM: Unknown device 0537 > > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- > > ParErr- Stepping- SERR- FastB2B- > > Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > > <TAbort- <MAbort- >SERR- <PERR- > > Latency: 0 > > Interrupt: pin B routed to IRQ 10 > > Region 0: I/O ports at 1c00 > > Region 1: I/O ports at 18c0 [size=64] > > Region 2: Memory at c0000c00 (32-bit, non-prefetchable) > > [size=512] Region 3: Memory at c0000800 (32-bit, non-prefetchable) > > [size=256] Capabilities: [50] Power Management version 2 > > Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA > > PME(D0+,D1-,D2-,D3hot+,D3cold+) > > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > > > > 0000:00:1f.6 Modem: Intel Corp. 82801DB (ICH4) AC'97 Modem Controller > > (rev 01) (prog-if 00 [Generic]) > > Subsystem: IBM: Unknown device 0525 > > Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- > > ParErr- Stepping- SERR- FastB2B- > > Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > > <TAbort- <MAbort- >SERR- <PERR- > > Latency: 0 > > Interrupt: pin B routed to IRQ 10 > > Region 0: I/O ports at 2400 > > Region 1: I/O ports at 2000 [size=128] > > Capabilities: [50] Power Management version 2 > > Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA > > PME(D0+,D1-,D2-,D3hot+,D3cold+) > > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > > > > 0000:01:00.0 VGA compatible controller: ATI Technologies Inc Radeon R250 > > Lf [Radeon Mobility 9000 M9] (rev 02) (prog-if 00 [VGA]) > > Subsystem: IBM: Unknown device 054d > > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- > > ParErr- Stepping+ SERR+ FastB2B+ > > Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > > <TAbort- <MAbort- >SERR- <PERR- > > Latency: 66 (2000ns min), Cache Line Size: 0x08 (32 bytes) > > Interrupt: pin A routed to IRQ 9 > > Region 0: Memory at e0000000 (32-bit, prefetchable) > > Region 1: I/O ports at 3000 [size=256] > > Region 2: Memory at c0100000 (32-bit, non-prefetchable) > > [size=64K] Capabilities: [58] AGP version 2.0 > > Status: RQ=48 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- > > HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4 > > Command: RQ=32 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW- > > Rate=x2 > > Capabilities: [50] Power Management version 2 > > Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA > > PME(D0-,D1-,D2-,D3hot-,D3cold-) > > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > > > > 0000:02:00.0 CardBus bridge: Texas Instruments PCI1520 PC card Cardbus > > Controller (rev 01) > > Subsystem: IBM ThinkPad T30/T40 > > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- > > ParErr- Stepping- SERR- FastB2B- > > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- > > <TAbort- <MAbort- >SERR- <PERR- > > Latency: 168, Cache Line Size: 0x20 (128 bytes) > > Interrupt: pin A routed to IRQ 9 > > Region 0: Memory at b0000000 (32-bit, non-prefetchable) > > Bus: primary=02, secondary=03, subordinate=06, sec-latency=176 > > Memory window 0: 20400000-207ff000 (prefetchable) > > Memory window 1: 20800000-20bff000 > > I/O window 0: 00004000-000040ff > > I/O window 1: 00004400-000044ff > > BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ > > PostWrite+ 16-bit legacy interface ports at 0001 > > > > 0000:02:00.1 CardBus bridge: Texas Instruments PCI1520 PC card Cardbus > > Controller (rev 01) > > Subsystem: IBM ThinkPad T30/T40 > > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- > > ParErr- Stepping- SERR- FastB2B- > > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- > > <TAbort- <MAbort- >SERR- <PERR- > > Latency: 168, Cache Line Size: 0x20 (128 bytes) > > Interrupt: pin B routed to IRQ 10 > > Region 0: Memory at b1000000 (32-bit, non-prefetchable) > > Bus: primary=02, secondary=07, subordinate=0a, sec-latency=176 > > Memory window 0: 20c00000-20fff000 (prefetchable) > > Memory window 1: 21000000-213ff000 > > I/O window 0: 00004800-000048ff > > I/O window 1: 00004c00-00004cff > > BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ > > PostWrite+ 16-bit legacy interface ports at 0001 > > > > 0000:02:01.0 Ethernet controller: Intel Corp. 82540EP Gigabit Ethernet > > Controller (Mobile) (rev 03) > > Subsystem: IBM PRO/1000 MT Mobile Connection > > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- > > ParErr- Stepping- SERR+ FastB2B- > > Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- > > <TAbort- <MAbort- >SERR- <PERR- > > Latency: 64 (63750ns min), Cache Line Size: 0x08 (32 bytes) > > Interrupt: pin A routed to IRQ 9 > > Region 0: Memory at c0220000 (32-bit, non-prefetchable) > > Region 1: Memory at c0200000 (32-bit, non-prefetchable) > > [size=64K] Region 2: I/O ports at 8000 [size=64] > > Capabilities: [dc] Power Management version 2 > > Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA > > PME(D0+,D1-,D2-,D3hot+,D3cold+) > > Status: D0 PME-Enable- DSel=0 DScale=1 PME- > > Capabilities: [f0] Message Signalled Interrupts: 64bit+ Queue=0/0 > > Enable- > > Address: 0000000000000000 Data: 0000 > > > > 0000:02:02.0 Ethernet controller: Atheros Communications, Inc. AR5211 > > 802.11ab NIC (rev 01) > > Subsystem: Unknown device 17ab:8310 > > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- > > ParErr- Stepping- SERR+ FastB2B- > > Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > > <TAbort- <MAbort- >SERR- <PERR- > > Latency: 80 (2500ns min, 7000ns max), Cache Line Size: 0x08 (32 > > bytes) Interrupt: pin A routed to IRQ 11 > > Region 0: Memory at c0210000 (32-bit, non-prefetchable) > > Capabilities: [44] Power Management version 2 > > Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA > > PME(D0-,D1-,D2-,D3hot-,D3cold-) > > Status: D0 PME-Enable- DSel=0 DScale=2 PME- > > > > dmesges attached. > > > > regards > > Alex > > > > Am Montag, 21. Juni 2004 19:50 schrieb Alexander Gran: > > > Hi, > > > > > > just a quick note: > > > Since 2.6.7-mm1 acpi C3 works even with usb and radeon loaded. > > > Great work! > > > > > > regards > > > Alex -- Encrypted Mails welcome. PGP-Key at http://zodiac.dnsalias.org/misc/pgpkey.asc | Key-ID: 0x6D7DD291 [-- Attachment #2: signature --] [-- Type: application/pgp-signature, Size: 189 bytes --] ^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: Linux 2.6.7-mm1, IBM T40p, ACPI C3 finally working. 2004-06-25 14:05 ` Alexander Gran @ 2004-06-25 17:30 ` Adam Sulmicki 2004-06-25 18:08 ` Alexander Gran 0 siblings, 1 reply; 8+ messages in thread From: Adam Sulmicki @ 2004-06-25 17:30 UTC (permalink / raw) To: Alexander Gran; +Cc: linux-kernel, linux-thinkpad ugh. so you say you reverted whole ACPI patch and it did not help? that's actually surprising since it would mean that the problem is outside of the ACPI code. if you are up to, you probably could do a binary search to see which particular sub-partch of the mm2 is responsible for the regression. On Fri, 25 Jun 2004, Alexander Gran wrote: > Sorry, did not help: > alex@t40:/proc/acpi/processor/CPU$ cat power > active state: C2 > default state: C1 > bus master activity: ffffffff > states: > C1: promotion[C2] demotion[--] latency[000] > usage[00000010] > *C2: promotion[C3] demotion[C1] latency[001] > usage[00164425] > C3: promotion[--] demotion[C2] latency[085] > usage[00000000] > > regards > Alex > > > Am Freitag, 25. Juni 2004 04:51 schrieb Adam Sulmicki: > > can you try to revert this sub-patch and see if it helps? > > > > ftp://ftp.kernel.org/pub/linux/kernel/people/akpm/patches/2.6/2.6.7/2.6.7-m > >m2/broken-out/bk-acpi.patch > > > > it would be really nice to have T40? working in 2.6.8 proper. > > > > On Fri, 25 Jun 2004, Alexander Gran wrote: > > > Ok guys, now this is strange. > > > > > > since 2.6.7-mm2 C3 does not work any longer. No idea why. > > > Same config, same system: > > > IBM t40p, 2373-g1g. > > > lspci -vvv: > > > root@t40:~# lspci -vvv > > > 0000:00:00.0 Host bridge: Intel Corp. 82855PM Processor to I/O Controller > > > (rev 03) > > > Subsystem: IBM: Unknown device 0529 > > > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- > > > ParErr- Stepping- SERR+ FastB2B- > > > Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- > > > <TAbort- <MAbort+ >SERR- <PERR- > > > Latency: 0 > > > Region 0: Memory at d0000000 (32-bit, prefetchable) > > > Capabilities: [e4] #09 [f104] > > > Capabilities: [a0] AGP version 2.0 > > > Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- > > > HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4 > > > Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW- > > > Rate=x2 > > > > > > 0000:00:01.0 PCI bridge: Intel Corp. 82855PM Processor to AGP Controller > > > (rev 03) (prog-if 00 [Normal decode]) > > > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- > > > ParErr- Stepping- SERR+ FastB2B- > > > Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- > > > <TAbort- <MAbort- >SERR- <PERR- > > > Latency: 96 > > > Bus: primary=00, secondary=01, subordinate=01, sec-latency=64 > > > I/O behind bridge: 00003000-00003fff > > > Memory behind bridge: c0100000-c01fffff > > > Prefetchable memory behind bridge: e0000000-e7ffffff > > > Expansion ROM at 00003000 [disabled] [size=4K] > > > BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B- > > > > > > 0000:00:1d.0 USB Controller: Intel Corp. 82801DB (ICH4) USB UHCI #1 (rev > > > 01) (prog-if 00 [UHCI]) > > > Subsystem: IBM: Unknown device 052d > > > Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- > > > ParErr- Stepping- SERR- FastB2B- > > > Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > > > <TAbort- <MAbort- >SERR- <PERR- > > > Latency: 0 > > > Interrupt: pin A routed to IRQ 9 > > > Region 4: I/O ports at 1800 [size=32] > > > > > > 0000:00:1d.1 USB Controller: Intel Corp. 82801DB (ICH4) USB UHCI #2 (rev > > > 01) (prog-if 00 [UHCI]) > > > Subsystem: IBM: Unknown device 052d > > > Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- > > > ParErr- Stepping- SERR- FastB2B- > > > Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > > > <TAbort- <MAbort- >SERR- <PERR- > > > Latency: 0 > > > Interrupt: pin B routed to IRQ 10 > > > Region 4: I/O ports at 1820 [size=32] > > > > > > 0000:00:1d.2 USB Controller: Intel Corp. 82801DB (ICH4) USB UHCI #3 (rev > > > 01) (prog-if 00 [UHCI]) > > > Subsystem: IBM: Unknown device 052d > > > Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- > > > ParErr- Stepping- SERR- FastB2B- > > > Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > > > <TAbort- <MAbort- >SERR- <PERR- > > > Latency: 0 > > > Interrupt: pin C routed to IRQ 11 > > > Region 4: I/O ports at 1840 [size=32] > > > > > > 0000:00:1d.7 USB Controller: Intel Corp. 82801DB (ICH4) USB2 EHCI > > > Controller (rev 01) (prog-if 20 [EHCI]) > > > Subsystem: IBM: Unknown device 052e > > > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- > > > ParErr- Stepping- SERR+ FastB2B- > > > Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > > > <TAbort- <MAbort- >SERR- <PERR- > > > Latency: 0 > > > Interrupt: pin D routed to IRQ 10 > > > Region 0: Memory at c0000000 (32-bit, non-prefetchable) > > > Capabilities: [50] Power Management version 2 > > > Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA > > > PME(D0+,D1-,D2-,D3hot+,D3cold+) > > > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > > > Capabilities: [58] #0a [2080] > > > > > > 0000:00:1e.0 PCI bridge: Intel Corp. 82801BAM/CAM PCI Bridge (rev 81) > > > (prog-if 00 [Normal decode]) > > > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- > > > ParErr- Stepping- SERR+ FastB2B- > > > Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- > > > <TAbort- <MAbort- >SERR- <PERR+ > > > Latency: 0 > > > Bus: primary=00, secondary=02, subordinate=08, sec-latency=168 > > > I/O behind bridge: 00004000-00008fff > > > Memory behind bridge: c0200000-cfffffff > > > Prefetchable memory behind bridge: e8000000-efffffff > > > BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B- > > > > > > 0000:00:1f.0 ISA bridge: Intel Corp. 82801DBM LPC Interface Controller > > > (rev 01) > > > Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- > > > ParErr- Stepping- SERR- FastB2B- > > > Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > > > <TAbort- <MAbort- >SERR- <PERR- > > > Latency: 0 > > > > > > 0000:00:1f.1 IDE interface: Intel Corp. 82801DBM (ICH4) Ultra ATA Storage > > > Controller (rev 01) (prog-if 8a [Master SecP PriP]) > > > Subsystem: IBM: Unknown device 052d > > > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- > > > ParErr- Stepping- SERR- FastB2B- > > > Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > > > <TAbort- <MAbort- >SERR- <PERR- > > > Latency: 0 > > > Interrupt: pin A routed to IRQ 11 > > > Region 0: I/O ports at <unassigned> > > > Region 1: I/O ports at <unassigned> > > > Region 2: I/O ports at <unassigned> > > > Region 3: I/O ports at <unassigned> > > > Region 4: I/O ports at 1860 [size=16] > > > Region 5: Memory at 20000000 (32-bit, non-prefetchable) [size=1K] > > > > > > 0000:00:1f.3 SMBus: Intel Corp. 82801DB/DBM (ICH4) SMBus Controller (rev > > > 01) Subsystem: IBM: Unknown device 052d > > > Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- > > > ParErr- Stepping- SERR- FastB2B- > > > Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > > > <TAbort- <MAbort- >SERR- <PERR- > > > Interrupt: pin B routed to IRQ 10 > > > Region 4: I/O ports at 1880 [size=32] > > > > > > 0000:00:1f.5 Multimedia audio controller: Intel Corp. 82801DB (ICH4) > > > AC'97 Audio Controller (rev 01) > > > Subsystem: IBM: Unknown device 0537 > > > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- > > > ParErr- Stepping- SERR- FastB2B- > > > Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > > > <TAbort- <MAbort- >SERR- <PERR- > > > Latency: 0 > > > Interrupt: pin B routed to IRQ 10 > > > Region 0: I/O ports at 1c00 > > > Region 1: I/O ports at 18c0 [size=64] > > > Region 2: Memory at c0000c00 (32-bit, non-prefetchable) > > > [size=512] Region 3: Memory at c0000800 (32-bit, non-prefetchable) > > > [size=256] Capabilities: [50] Power Management version 2 > > > Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA > > > PME(D0+,D1-,D2-,D3hot+,D3cold+) > > > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > > > > > > 0000:00:1f.6 Modem: Intel Corp. 82801DB (ICH4) AC'97 Modem Controller > > > (rev 01) (prog-if 00 [Generic]) > > > Subsystem: IBM: Unknown device 0525 > > > Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- > > > ParErr- Stepping- SERR- FastB2B- > > > Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > > > <TAbort- <MAbort- >SERR- <PERR- > > > Latency: 0 > > > Interrupt: pin B routed to IRQ 10 > > > Region 0: I/O ports at 2400 > > > Region 1: I/O ports at 2000 [size=128] > > > Capabilities: [50] Power Management version 2 > > > Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA > > > PME(D0+,D1-,D2-,D3hot+,D3cold+) > > > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > > > > > > 0000:01:00.0 VGA compatible controller: ATI Technologies Inc Radeon R250 > > > Lf [Radeon Mobility 9000 M9] (rev 02) (prog-if 00 [VGA]) > > > Subsystem: IBM: Unknown device 054d > > > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- > > > ParErr- Stepping+ SERR+ FastB2B+ > > > Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > > > <TAbort- <MAbort- >SERR- <PERR- > > > Latency: 66 (2000ns min), Cache Line Size: 0x08 (32 bytes) > > > Interrupt: pin A routed to IRQ 9 > > > Region 0: Memory at e0000000 (32-bit, prefetchable) > > > Region 1: I/O ports at 3000 [size=256] > > > Region 2: Memory at c0100000 (32-bit, non-prefetchable) > > > [size=64K] Capabilities: [58] AGP version 2.0 > > > Status: RQ=48 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- > > > HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4 > > > Command: RQ=32 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW- > > > Rate=x2 > > > Capabilities: [50] Power Management version 2 > > > Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA > > > PME(D0-,D1-,D2-,D3hot-,D3cold-) > > > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > > > > > > 0000:02:00.0 CardBus bridge: Texas Instruments PCI1520 PC card Cardbus > > > Controller (rev 01) > > > Subsystem: IBM ThinkPad T30/T40 > > > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- > > > ParErr- Stepping- SERR- FastB2B- > > > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- > > > <TAbort- <MAbort- >SERR- <PERR- > > > Latency: 168, Cache Line Size: 0x20 (128 bytes) > > > Interrupt: pin A routed to IRQ 9 > > > Region 0: Memory at b0000000 (32-bit, non-prefetchable) > > > Bus: primary=02, secondary=03, subordinate=06, sec-latency=176 > > > Memory window 0: 20400000-207ff000 (prefetchable) > > > Memory window 1: 20800000-20bff000 > > > I/O window 0: 00004000-000040ff > > > I/O window 1: 00004400-000044ff > > > BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ > > > PostWrite+ 16-bit legacy interface ports at 0001 > > > > > > 0000:02:00.1 CardBus bridge: Texas Instruments PCI1520 PC card Cardbus > > > Controller (rev 01) > > > Subsystem: IBM ThinkPad T30/T40 > > > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- > > > ParErr- Stepping- SERR- FastB2B- > > > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- > > > <TAbort- <MAbort- >SERR- <PERR- > > > Latency: 168, Cache Line Size: 0x20 (128 bytes) > > > Interrupt: pin B routed to IRQ 10 > > > Region 0: Memory at b1000000 (32-bit, non-prefetchable) > > > Bus: primary=02, secondary=07, subordinate=0a, sec-latency=176 > > > Memory window 0: 20c00000-20fff000 (prefetchable) > > > Memory window 1: 21000000-213ff000 > > > I/O window 0: 00004800-000048ff > > > I/O window 1: 00004c00-00004cff > > > BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ > > > PostWrite+ 16-bit legacy interface ports at 0001 > > > > > > 0000:02:01.0 Ethernet controller: Intel Corp. 82540EP Gigabit Ethernet > > > Controller (Mobile) (rev 03) > > > Subsystem: IBM PRO/1000 MT Mobile Connection > > > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- > > > ParErr- Stepping- SERR+ FastB2B- > > > Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- > > > <TAbort- <MAbort- >SERR- <PERR- > > > Latency: 64 (63750ns min), Cache Line Size: 0x08 (32 bytes) > > > Interrupt: pin A routed to IRQ 9 > > > Region 0: Memory at c0220000 (32-bit, non-prefetchable) > > > Region 1: Memory at c0200000 (32-bit, non-prefetchable) > > > [size=64K] Region 2: I/O ports at 8000 [size=64] > > > Capabilities: [dc] Power Management version 2 > > > Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA > > > PME(D0+,D1-,D2-,D3hot+,D3cold+) > > > Status: D0 PME-Enable- DSel=0 DScale=1 PME- > > > Capabilities: [f0] Message Signalled Interrupts: 64bit+ Queue=0/0 > > > Enable- > > > Address: 0000000000000000 Data: 0000 > > > > > > 0000:02:02.0 Ethernet controller: Atheros Communications, Inc. AR5211 > > > 802.11ab NIC (rev 01) > > > Subsystem: Unknown device 17ab:8310 > > > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- > > > ParErr- Stepping- SERR+ FastB2B- > > > Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > > > <TAbort- <MAbort- >SERR- <PERR- > > > Latency: 80 (2500ns min, 7000ns max), Cache Line Size: 0x08 (32 > > > bytes) Interrupt: pin A routed to IRQ 11 > > > Region 0: Memory at c0210000 (32-bit, non-prefetchable) > > > Capabilities: [44] Power Management version 2 > > > Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA > > > PME(D0-,D1-,D2-,D3hot-,D3cold-) > > > Status: D0 PME-Enable- DSel=0 DScale=2 PME- > > > > > > dmesges attached. > > > > > > regards > > > Alex > > > > > > Am Montag, 21. Juni 2004 19:50 schrieb Alexander Gran: > > > > Hi, > > > > > > > > just a quick note: > > > > Since 2.6.7-mm1 acpi C3 works even with usb and radeon loaded. > > > > Great work! > > > > > > > > regards > > > > Alex > > -- > Encrypted Mails welcome. > PGP-Key at http://zodiac.dnsalias.org/misc/pgpkey.asc | Key-ID: 0x6D7DD291 > ^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: Linux 2.6.7-mm1, IBM T40p, ACPI C3 finally working. 2004-06-25 17:30 ` Adam Sulmicki @ 2004-06-25 18:08 ` Alexander Gran 2004-06-25 19:04 ` Adam Sulmicki 0 siblings, 1 reply; 8+ messages in thread From: Alexander Gran @ 2004-06-25 18:08 UTC (permalink / raw) To: Adam Sulmicki; +Cc: linux-kernel, linux-thinkpad -----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Yes. i did a patch -R -p1 < ..bk-acpi.patch But checking every single patch seems a bit clumsy to me. I suppose anyone has changed something that busmasters all the time. Isn't there an easier way to tell what patch it was? regards Alex Am Freitag, 25. Juni 2004 19:30 schrieb Adam Sulmicki: > ugh. so you say you reverted whole ACPI patch and it did not help? that's > actually surprising since it would mean that the problem is outside of the > ACPI code. > > if you are up to, you probably could do a binary search to see which > particular sub-partch of the mm2 is responsible for the regression. > > On Fri, 25 Jun 2004, Alexander Gran wrote: > > Sorry, did not help: > > alex@t40:/proc/acpi/processor/CPU$ cat power > > active state: C2 > > default state: C1 > > bus master activity: ffffffff > > states: > > C1: promotion[C2] demotion[--] latency[000] > > usage[00000010] > > *C2: promotion[C3] demotion[C1] latency[001] > > usage[00164425] > > C3: promotion[--] demotion[C2] latency[085] > > usage[00000000] > > > > regards > > Alex > > > > Am Freitag, 25. Juni 2004 04:51 schrieb Adam Sulmicki: > > > can you try to revert this sub-patch and see if it helps? > > > > > > ftp://ftp.kernel.org/pub/linux/kernel/people/akpm/patches/2.6/2.6.7/2.6 > > >.7-m m2/broken-out/bk-acpi.patch > > > > > > it would be really nice to have T40? working in 2.6.8 proper. > > > > > > On Fri, 25 Jun 2004, Alexander Gran wrote: > > > > Ok guys, now this is strange. > > > > > > > > since 2.6.7-mm2 C3 does not work any longer. No idea why. > > > > Same config, same system: > > > > IBM t40p, 2373-g1g. > > > > lspci -vvv: > > > > root@t40:~# lspci -vvv > > > > 0000:00:00.0 Host bridge: Intel Corp. 82855PM Processor to I/O > > > > Controller (rev 03) > > > > Subsystem: IBM: Unknown device 0529 > > > > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- > > > > ParErr- Stepping- SERR+ FastB2B- > > > > Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast > > > > >TAbort- <TAbort- <MAbort+ >SERR- <PERR- > > > > Latency: 0 > > > > Region 0: Memory at d0000000 (32-bit, prefetchable) > > > > Capabilities: [e4] #09 [f104] > > > > Capabilities: [a0] AGP version 2.0 > > > > Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- > > > > HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4 > > > > Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- > > > > FW- Rate=x2 > > > > > > > > 0000:00:01.0 PCI bridge: Intel Corp. 82855PM Processor to AGP > > > > Controller (rev 03) (prog-if 00 [Normal decode]) > > > > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- > > > > ParErr- Stepping- SERR+ FastB2B- > > > > Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast > > > > >TAbort- <TAbort- <MAbort- >SERR- <PERR- > > > > Latency: 96 > > > > Bus: primary=00, secondary=01, subordinate=01, sec-latency=64 > > > > I/O behind bridge: 00003000-00003fff > > > > Memory behind bridge: c0100000-c01fffff > > > > Prefetchable memory behind bridge: e0000000-e7ffffff > > > > Expansion ROM at 00003000 [disabled] [size=4K] > > > > BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B- > > > > > > > > 0000:00:1d.0 USB Controller: Intel Corp. 82801DB (ICH4) USB UHCI #1 > > > > (rev 01) (prog-if 00 [UHCI]) > > > > Subsystem: IBM: Unknown device 052d > > > > Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- > > > > ParErr- Stepping- SERR- FastB2B- > > > > Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium > > > > >TAbort- <TAbort- <MAbort- >SERR- <PERR- > > > > Latency: 0 > > > > Interrupt: pin A routed to IRQ 9 > > > > Region 4: I/O ports at 1800 [size=32] > > > > > > > > 0000:00:1d.1 USB Controller: Intel Corp. 82801DB (ICH4) USB UHCI #2 > > > > (rev 01) (prog-if 00 [UHCI]) > > > > Subsystem: IBM: Unknown device 052d > > > > Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- > > > > ParErr- Stepping- SERR- FastB2B- > > > > Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium > > > > >TAbort- <TAbort- <MAbort- >SERR- <PERR- > > > > Latency: 0 > > > > Interrupt: pin B routed to IRQ 10 > > > > Region 4: I/O ports at 1820 [size=32] > > > > > > > > 0000:00:1d.2 USB Controller: Intel Corp. 82801DB (ICH4) USB UHCI #3 > > > > (rev 01) (prog-if 00 [UHCI]) > > > > Subsystem: IBM: Unknown device 052d > > > > Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- > > > > ParErr- Stepping- SERR- FastB2B- > > > > Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium > > > > >TAbort- <TAbort- <MAbort- >SERR- <PERR- > > > > Latency: 0 > > > > Interrupt: pin C routed to IRQ 11 > > > > Region 4: I/O ports at 1840 [size=32] > > > > > > > > 0000:00:1d.7 USB Controller: Intel Corp. 82801DB (ICH4) USB2 EHCI > > > > Controller (rev 01) (prog-if 20 [EHCI]) > > > > Subsystem: IBM: Unknown device 052e > > > > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- > > > > ParErr- Stepping- SERR+ FastB2B- > > > > Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium > > > > >TAbort- <TAbort- <MAbort- >SERR- <PERR- > > > > Latency: 0 > > > > Interrupt: pin D routed to IRQ 10 > > > > Region 0: Memory at c0000000 (32-bit, non-prefetchable) > > > > Capabilities: [50] Power Management version 2 > > > > Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA > > > > PME(D0+,D1-,D2-,D3hot+,D3cold+) > > > > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > > > > Capabilities: [58] #0a [2080] > > > > > > > > 0000:00:1e.0 PCI bridge: Intel Corp. 82801BAM/CAM PCI Bridge (rev 81) > > > > (prog-if 00 [Normal decode]) > > > > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- > > > > ParErr- Stepping- SERR+ FastB2B- > > > > Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast > > > > >TAbort- <TAbort- <MAbort- >SERR- <PERR+ > > > > Latency: 0 > > > > Bus: primary=00, secondary=02, subordinate=08, > > > > sec-latency=168 I/O behind bridge: 00004000-00008fff > > > > Memory behind bridge: c0200000-cfffffff > > > > Prefetchable memory behind bridge: e8000000-efffffff > > > > BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B- > > > > > > > > 0000:00:1f.0 ISA bridge: Intel Corp. 82801DBM LPC Interface > > > > Controller (rev 01) > > > > Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- > > > > ParErr- Stepping- SERR- FastB2B- > > > > Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium > > > > >TAbort- <TAbort- <MAbort- >SERR- <PERR- > > > > Latency: 0 > > > > > > > > 0000:00:1f.1 IDE interface: Intel Corp. 82801DBM (ICH4) Ultra ATA > > > > Storage Controller (rev 01) (prog-if 8a [Master SecP PriP]) > > > > Subsystem: IBM: Unknown device 052d > > > > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- > > > > ParErr- Stepping- SERR- FastB2B- > > > > Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium > > > > >TAbort- <TAbort- <MAbort- >SERR- <PERR- > > > > Latency: 0 > > > > Interrupt: pin A routed to IRQ 11 > > > > Region 0: I/O ports at <unassigned> > > > > Region 1: I/O ports at <unassigned> > > > > Region 2: I/O ports at <unassigned> > > > > Region 3: I/O ports at <unassigned> > > > > Region 4: I/O ports at 1860 [size=16] > > > > Region 5: Memory at 20000000 (32-bit, non-prefetchable) > > > > [size=1K] > > > > > > > > 0000:00:1f.3 SMBus: Intel Corp. 82801DB/DBM (ICH4) SMBus Controller > > > > (rev 01) Subsystem: IBM: Unknown device 052d > > > > Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- > > > > ParErr- Stepping- SERR- FastB2B- > > > > Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium > > > > >TAbort- <TAbort- <MAbort- >SERR- <PERR- > > > > Interrupt: pin B routed to IRQ 10 > > > > Region 4: I/O ports at 1880 [size=32] > > > > > > > > 0000:00:1f.5 Multimedia audio controller: Intel Corp. 82801DB (ICH4) > > > > AC'97 Audio Controller (rev 01) > > > > Subsystem: IBM: Unknown device 0537 > > > > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- > > > > ParErr- Stepping- SERR- FastB2B- > > > > Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium > > > > >TAbort- <TAbort- <MAbort- >SERR- <PERR- > > > > Latency: 0 > > > > Interrupt: pin B routed to IRQ 10 > > > > Region 0: I/O ports at 1c00 > > > > Region 1: I/O ports at 18c0 [size=64] > > > > Region 2: Memory at c0000c00 (32-bit, non-prefetchable) > > > > [size=512] Region 3: Memory at c0000800 (32-bit, non-prefetchable) > > > > [size=256] Capabilities: [50] Power Management version 2 > > > > Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA > > > > PME(D0+,D1-,D2-,D3hot+,D3cold+) > > > > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > > > > > > > > 0000:00:1f.6 Modem: Intel Corp. 82801DB (ICH4) AC'97 Modem Controller > > > > (rev 01) (prog-if 00 [Generic]) > > > > Subsystem: IBM: Unknown device 0525 > > > > Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- > > > > ParErr- Stepping- SERR- FastB2B- > > > > Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium > > > > >TAbort- <TAbort- <MAbort- >SERR- <PERR- > > > > Latency: 0 > > > > Interrupt: pin B routed to IRQ 10 > > > > Region 0: I/O ports at 2400 > > > > Region 1: I/O ports at 2000 [size=128] > > > > Capabilities: [50] Power Management version 2 > > > > Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA > > > > PME(D0+,D1-,D2-,D3hot+,D3cold+) > > > > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > > > > > > > > 0000:01:00.0 VGA compatible controller: ATI Technologies Inc Radeon > > > > R250 Lf [Radeon Mobility 9000 M9] (rev 02) (prog-if 00 [VGA]) > > > > Subsystem: IBM: Unknown device 054d > > > > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- > > > > ParErr- Stepping+ SERR+ FastB2B+ > > > > Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium > > > > >TAbort- <TAbort- <MAbort- >SERR- <PERR- > > > > Latency: 66 (2000ns min), Cache Line Size: 0x08 (32 bytes) > > > > Interrupt: pin A routed to IRQ 9 > > > > Region 0: Memory at e0000000 (32-bit, prefetchable) > > > > Region 1: I/O ports at 3000 [size=256] > > > > Region 2: Memory at c0100000 (32-bit, non-prefetchable) > > > > [size=64K] Capabilities: [58] AGP version 2.0 > > > > Status: RQ=48 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- > > > > HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4 > > > > Command: RQ=32 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- > > > > FW- Rate=x2 > > > > Capabilities: [50] Power Management version 2 > > > > Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA > > > > PME(D0-,D1-,D2-,D3hot-,D3cold-) > > > > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > > > > > > > > 0000:02:00.0 CardBus bridge: Texas Instruments PCI1520 PC card > > > > Cardbus Controller (rev 01) > > > > Subsystem: IBM ThinkPad T30/T40 > > > > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- > > > > ParErr- Stepping- SERR- FastB2B- > > > > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium > > > > >TAbort- <TAbort- <MAbort- >SERR- <PERR- > > > > Latency: 168, Cache Line Size: 0x20 (128 bytes) > > > > Interrupt: pin A routed to IRQ 9 > > > > Region 0: Memory at b0000000 (32-bit, non-prefetchable) > > > > Bus: primary=02, secondary=03, subordinate=06, > > > > sec-latency=176 Memory window 0: 20400000-207ff000 (prefetchable) > > > > Memory window 1: 20800000-20bff000 > > > > I/O window 0: 00004000-000040ff > > > > I/O window 1: 00004400-000044ff > > > > BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ > > > > PostWrite+ 16-bit legacy interface ports at 0001 > > > > > > > > 0000:02:00.1 CardBus bridge: Texas Instruments PCI1520 PC card > > > > Cardbus Controller (rev 01) > > > > Subsystem: IBM ThinkPad T30/T40 > > > > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- > > > > ParErr- Stepping- SERR- FastB2B- > > > > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium > > > > >TAbort- <TAbort- <MAbort- >SERR- <PERR- > > > > Latency: 168, Cache Line Size: 0x20 (128 bytes) > > > > Interrupt: pin B routed to IRQ 10 > > > > Region 0: Memory at b1000000 (32-bit, non-prefetchable) > > > > Bus: primary=02, secondary=07, subordinate=0a, > > > > sec-latency=176 Memory window 0: 20c00000-20fff000 (prefetchable) > > > > Memory window 1: 21000000-213ff000 > > > > I/O window 0: 00004800-000048ff > > > > I/O window 1: 00004c00-00004cff > > > > BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ > > > > PostWrite+ 16-bit legacy interface ports at 0001 > > > > > > > > 0000:02:01.0 Ethernet controller: Intel Corp. 82540EP Gigabit > > > > Ethernet Controller (Mobile) (rev 03) > > > > Subsystem: IBM PRO/1000 MT Mobile Connection > > > > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- > > > > ParErr- Stepping- SERR+ FastB2B- > > > > Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium > > > > >TAbort- <TAbort- <MAbort- >SERR- <PERR- > > > > Latency: 64 (63750ns min), Cache Line Size: 0x08 (32 bytes) > > > > Interrupt: pin A routed to IRQ 9 > > > > Region 0: Memory at c0220000 (32-bit, non-prefetchable) > > > > Region 1: Memory at c0200000 (32-bit, non-prefetchable) > > > > [size=64K] Region 2: I/O ports at 8000 [size=64] > > > > Capabilities: [dc] Power Management version 2 > > > > Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA > > > > PME(D0+,D1-,D2-,D3hot+,D3cold+) > > > > Status: D0 PME-Enable- DSel=0 DScale=1 PME- > > > > Capabilities: [f0] Message Signalled Interrupts: 64bit+ > > > > Queue=0/0 Enable- > > > > Address: 0000000000000000 Data: 0000 > > > > > > > > 0000:02:02.0 Ethernet controller: Atheros Communications, Inc. AR5211 > > > > 802.11ab NIC (rev 01) > > > > Subsystem: Unknown device 17ab:8310 > > > > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- > > > > ParErr- Stepping- SERR+ FastB2B- > > > > Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium > > > > >TAbort- <TAbort- <MAbort- >SERR- <PERR- > > > > Latency: 80 (2500ns min, 7000ns max), Cache Line Size: 0x08 > > > > (32 bytes) Interrupt: pin A routed to IRQ 11 > > > > Region 0: Memory at c0210000 (32-bit, non-prefetchable) > > > > Capabilities: [44] Power Management version 2 > > > > Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA > > > > PME(D0-,D1-,D2-,D3hot-,D3cold-) > > > > Status: D0 PME-Enable- DSel=0 DScale=2 PME- > > > > > > > > dmesges attached. > > > > > > > > regards > > > > Alex > > > > > > > > Am Montag, 21. Juni 2004 19:50 schrieb Alexander Gran: > > > > > Hi, > > > > > > > > > > just a quick note: > > > > > Since 2.6.7-mm1 acpi C3 works even with usb and radeon loaded. > > > > > Great work! > > > > > > > > > > regards > > > > > Alex - -- Encrypted Mails welcome. PGP-Key at http://zodiac.dnsalias.org/misc/pgpkey.asc | Key-ID: 0x6D7DD291 -----BEGIN PGP SIGNATURE----- Version: GnuPG v1.2.4 (GNU/Linux) iD8DBQFA3GoT/aHb+2190pERAlW2AJ446y3PzZY5u0LvxDxzHloiu6q0vgCgrt4K St69aZvzniJF+yl1GTpRoKU= =sptO -----END PGP SIGNATURE----- ^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: Linux 2.6.7-mm1, IBM T40p, ACPI C3 finally working. 2004-06-25 18:08 ` Alexander Gran @ 2004-06-25 19:04 ` Adam Sulmicki 2004-06-25 19:29 ` William Lee Irwin III 0 siblings, 1 reply; 8+ messages in thread From: Adam Sulmicki @ 2004-06-25 19:04 UTC (permalink / raw) To: Alexander Gran; +Cc: linux-kernel, linux-thinkpad not every single patch, a _binary search_ of patches. try logical half of mm2, see if it breaks, if not then try the other half. and so on recursively. On Fri, 25 Jun 2004, Alexander Gran wrote: > -----BEGIN PGP SIGNED MESSAGE----- > Hash: SHA1 > > Yes. i did a patch -R -p1 < ..bk-acpi.patch > But checking every single patch seems a bit clumsy to me. > I suppose anyone has changed something that busmasters all the time. Isn't > there an easier way to tell what patch it was? > > regards > Alex > > Am Freitag, 25. Juni 2004 19:30 schrieb Adam Sulmicki: > > ugh. so you say you reverted whole ACPI patch and it did not help? that's > > actually surprising since it would mean that the problem is outside of the > > ACPI code. > > > > if you are up to, you probably could do a binary search to see which > > particular sub-partch of the mm2 is responsible for the regression. > > > > On Fri, 25 Jun 2004, Alexander Gran wrote: > > > Sorry, did not help: > > > alex@t40:/proc/acpi/processor/CPU$ cat power > > > active state: C2 > > > default state: C1 > > > bus master activity: ffffffff > > > states: > > > C1: promotion[C2] demotion[--] latency[000] > > > usage[00000010] > > > *C2: promotion[C3] demotion[C1] latency[001] > > > usage[00164425] > > > C3: promotion[--] demotion[C2] latency[085] > > > usage[00000000] > > > > > > regards > > > Alex > > > > > > Am Freitag, 25. Juni 2004 04:51 schrieb Adam Sulmicki: > > > > can you try to revert this sub-patch and see if it helps? > > > > > > > > ftp://ftp.kernel.org/pub/linux/kernel/people/akpm/patches/2.6/2.6.7/2.6 > > > >.7-m m2/broken-out/bk-acpi.patch > > > > > > > > it would be really nice to have T40? working in 2.6.8 proper. > > > > > > > > On Fri, 25 Jun 2004, Alexander Gran wrote: > > > > > Ok guys, now this is strange. > > > > > > > > > > since 2.6.7-mm2 C3 does not work any longer. No idea why. > > > > > Same config, same system: > > > > > IBM t40p, 2373-g1g. > > > > > lspci -vvv: > > > > > root@t40:~# lspci -vvv > > > > > 0000:00:00.0 Host bridge: Intel Corp. 82855PM Processor to I/O > > > > > Controller (rev 03) > > > > > Subsystem: IBM: Unknown device 0529 > > > > > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- > > > > > ParErr- Stepping- SERR+ FastB2B- > > > > > Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast > > > > > >TAbort- <TAbort- <MAbort+ >SERR- <PERR- > > > > > Latency: 0 > > > > > Region 0: Memory at d0000000 (32-bit, prefetchable) > > > > > Capabilities: [e4] #09 [f104] > > > > > Capabilities: [a0] AGP version 2.0 > > > > > Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- > > > > > HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4 > > > > > Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- > > > > > FW- Rate=x2 > > > > > > > > > > 0000:00:01.0 PCI bridge: Intel Corp. 82855PM Processor to AGP > > > > > Controller (rev 03) (prog-if 00 [Normal decode]) > > > > > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- > > > > > ParErr- Stepping- SERR+ FastB2B- > > > > > Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast > > > > > >TAbort- <TAbort- <MAbort- >SERR- <PERR- > > > > > Latency: 96 > > > > > Bus: primary=00, secondary=01, subordinate=01, sec-latency=64 > > > > > I/O behind bridge: 00003000-00003fff > > > > > Memory behind bridge: c0100000-c01fffff > > > > > Prefetchable memory behind bridge: e0000000-e7ffffff > > > > > Expansion ROM at 00003000 [disabled] [size=4K] > > > > > BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B- > > > > > > > > > > 0000:00:1d.0 USB Controller: Intel Corp. 82801DB (ICH4) USB UHCI #1 > > > > > (rev 01) (prog-if 00 [UHCI]) > > > > > Subsystem: IBM: Unknown device 052d > > > > > Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- > > > > > ParErr- Stepping- SERR- FastB2B- > > > > > Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium > > > > > >TAbort- <TAbort- <MAbort- >SERR- <PERR- > > > > > Latency: 0 > > > > > Interrupt: pin A routed to IRQ 9 > > > > > Region 4: I/O ports at 1800 [size=32] > > > > > > > > > > 0000:00:1d.1 USB Controller: Intel Corp. 82801DB (ICH4) USB UHCI #2 > > > > > (rev 01) (prog-if 00 [UHCI]) > > > > > Subsystem: IBM: Unknown device 052d > > > > > Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- > > > > > ParErr- Stepping- SERR- FastB2B- > > > > > Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium > > > > > >TAbort- <TAbort- <MAbort- >SERR- <PERR- > > > > > Latency: 0 > > > > > Interrupt: pin B routed to IRQ 10 > > > > > Region 4: I/O ports at 1820 [size=32] > > > > > > > > > > 0000:00:1d.2 USB Controller: Intel Corp. 82801DB (ICH4) USB UHCI #3 > > > > > (rev 01) (prog-if 00 [UHCI]) > > > > > Subsystem: IBM: Unknown device 052d > > > > > Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- > > > > > ParErr- Stepping- SERR- FastB2B- > > > > > Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium > > > > > >TAbort- <TAbort- <MAbort- >SERR- <PERR- > > > > > Latency: 0 > > > > > Interrupt: pin C routed to IRQ 11 > > > > > Region 4: I/O ports at 1840 [size=32] > > > > > > > > > > 0000:00:1d.7 USB Controller: Intel Corp. 82801DB (ICH4) USB2 EHCI > > > > > Controller (rev 01) (prog-if 20 [EHCI]) > > > > > Subsystem: IBM: Unknown device 052e > > > > > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- > > > > > ParErr- Stepping- SERR+ FastB2B- > > > > > Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium > > > > > >TAbort- <TAbort- <MAbort- >SERR- <PERR- > > > > > Latency: 0 > > > > > Interrupt: pin D routed to IRQ 10 > > > > > Region 0: Memory at c0000000 (32-bit, non-prefetchable) > > > > > Capabilities: [50] Power Management version 2 > > > > > Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA > > > > > PME(D0+,D1-,D2-,D3hot+,D3cold+) > > > > > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > > > > > Capabilities: [58] #0a [2080] > > > > > > > > > > 0000:00:1e.0 PCI bridge: Intel Corp. 82801BAM/CAM PCI Bridge (rev 81) > > > > > (prog-if 00 [Normal decode]) > > > > > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- > > > > > ParErr- Stepping- SERR+ FastB2B- > > > > > Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast > > > > > >TAbort- <TAbort- <MAbort- >SERR- <PERR+ > > > > > Latency: 0 > > > > > Bus: primary=00, secondary=02, subordinate=08, > > > > > sec-latency=168 I/O behind bridge: 00004000-00008fff > > > > > Memory behind bridge: c0200000-cfffffff > > > > > Prefetchable memory behind bridge: e8000000-efffffff > > > > > BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B- > > > > > > > > > > 0000:00:1f.0 ISA bridge: Intel Corp. 82801DBM LPC Interface > > > > > Controller (rev 01) > > > > > Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- > > > > > ParErr- Stepping- SERR- FastB2B- > > > > > Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium > > > > > >TAbort- <TAbort- <MAbort- >SERR- <PERR- > > > > > Latency: 0 > > > > > > > > > > 0000:00:1f.1 IDE interface: Intel Corp. 82801DBM (ICH4) Ultra ATA > > > > > Storage Controller (rev 01) (prog-if 8a [Master SecP PriP]) > > > > > Subsystem: IBM: Unknown device 052d > > > > > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- > > > > > ParErr- Stepping- SERR- FastB2B- > > > > > Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium > > > > > >TAbort- <TAbort- <MAbort- >SERR- <PERR- > > > > > Latency: 0 > > > > > Interrupt: pin A routed to IRQ 11 > > > > > Region 0: I/O ports at <unassigned> > > > > > Region 1: I/O ports at <unassigned> > > > > > Region 2: I/O ports at <unassigned> > > > > > Region 3: I/O ports at <unassigned> > > > > > Region 4: I/O ports at 1860 [size=16] > > > > > Region 5: Memory at 20000000 (32-bit, non-prefetchable) > > > > > [size=1K] > > > > > > > > > > 0000:00:1f.3 SMBus: Intel Corp. 82801DB/DBM (ICH4) SMBus Controller > > > > > (rev 01) Subsystem: IBM: Unknown device 052d > > > > > Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- > > > > > ParErr- Stepping- SERR- FastB2B- > > > > > Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium > > > > > >TAbort- <TAbort- <MAbort- >SERR- <PERR- > > > > > Interrupt: pin B routed to IRQ 10 > > > > > Region 4: I/O ports at 1880 [size=32] > > > > > > > > > > 0000:00:1f.5 Multimedia audio controller: Intel Corp. 82801DB (ICH4) > > > > > AC'97 Audio Controller (rev 01) > > > > > Subsystem: IBM: Unknown device 0537 > > > > > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- > > > > > ParErr- Stepping- SERR- FastB2B- > > > > > Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium > > > > > >TAbort- <TAbort- <MAbort- >SERR- <PERR- > > > > > Latency: 0 > > > > > Interrupt: pin B routed to IRQ 10 > > > > > Region 0: I/O ports at 1c00 > > > > > Region 1: I/O ports at 18c0 [size=64] > > > > > Region 2: Memory at c0000c00 (32-bit, non-prefetchable) > > > > > [size=512] Region 3: Memory at c0000800 (32-bit, non-prefetchable) > > > > > [size=256] Capabilities: [50] Power Management version 2 > > > > > Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA > > > > > PME(D0+,D1-,D2-,D3hot+,D3cold+) > > > > > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > > > > > > > > > > 0000:00:1f.6 Modem: Intel Corp. 82801DB (ICH4) AC'97 Modem Controller > > > > > (rev 01) (prog-if 00 [Generic]) > > > > > Subsystem: IBM: Unknown device 0525 > > > > > Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- > > > > > ParErr- Stepping- SERR- FastB2B- > > > > > Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium > > > > > >TAbort- <TAbort- <MAbort- >SERR- <PERR- > > > > > Latency: 0 > > > > > Interrupt: pin B routed to IRQ 10 > > > > > Region 0: I/O ports at 2400 > > > > > Region 1: I/O ports at 2000 [size=128] > > > > > Capabilities: [50] Power Management version 2 > > > > > Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA > > > > > PME(D0+,D1-,D2-,D3hot+,D3cold+) > > > > > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > > > > > > > > > > 0000:01:00.0 VGA compatible controller: ATI Technologies Inc Radeon > > > > > R250 Lf [Radeon Mobility 9000 M9] (rev 02) (prog-if 00 [VGA]) > > > > > Subsystem: IBM: Unknown device 054d > > > > > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- > > > > > ParErr- Stepping+ SERR+ FastB2B+ > > > > > Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium > > > > > >TAbort- <TAbort- <MAbort- >SERR- <PERR- > > > > > Latency: 66 (2000ns min), Cache Line Size: 0x08 (32 bytes) > > > > > Interrupt: pin A routed to IRQ 9 > > > > > Region 0: Memory at e0000000 (32-bit, prefetchable) > > > > > Region 1: I/O ports at 3000 [size=256] > > > > > Region 2: Memory at c0100000 (32-bit, non-prefetchable) > > > > > [size=64K] Capabilities: [58] AGP version 2.0 > > > > > Status: RQ=48 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- > > > > > HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4 > > > > > Command: RQ=32 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- > > > > > FW- Rate=x2 > > > > > Capabilities: [50] Power Management version 2 > > > > > Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA > > > > > PME(D0-,D1-,D2-,D3hot-,D3cold-) > > > > > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > > > > > > > > > > 0000:02:00.0 CardBus bridge: Texas Instruments PCI1520 PC card > > > > > Cardbus Controller (rev 01) > > > > > Subsystem: IBM ThinkPad T30/T40 > > > > > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- > > > > > ParErr- Stepping- SERR- FastB2B- > > > > > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium > > > > > >TAbort- <TAbort- <MAbort- >SERR- <PERR- > > > > > Latency: 168, Cache Line Size: 0x20 (128 bytes) > > > > > Interrupt: pin A routed to IRQ 9 > > > > > Region 0: Memory at b0000000 (32-bit, non-prefetchable) > > > > > Bus: primary=02, secondary=03, subordinate=06, > > > > > sec-latency=176 Memory window 0: 20400000-207ff000 (prefetchable) > > > > > Memory window 1: 20800000-20bff000 > > > > > I/O window 0: 00004000-000040ff > > > > > I/O window 1: 00004400-000044ff > > > > > BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ > > > > > PostWrite+ 16-bit legacy interface ports at 0001 > > > > > > > > > > 0000:02:00.1 CardBus bridge: Texas Instruments PCI1520 PC card > > > > > Cardbus Controller (rev 01) > > > > > Subsystem: IBM ThinkPad T30/T40 > > > > > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- > > > > > ParErr- Stepping- SERR- FastB2B- > > > > > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium > > > > > >TAbort- <TAbort- <MAbort- >SERR- <PERR- > > > > > Latency: 168, Cache Line Size: 0x20 (128 bytes) > > > > > Interrupt: pin B routed to IRQ 10 > > > > > Region 0: Memory at b1000000 (32-bit, non-prefetchable) > > > > > Bus: primary=02, secondary=07, subordinate=0a, > > > > > sec-latency=176 Memory window 0: 20c00000-20fff000 (prefetchable) > > > > > Memory window 1: 21000000-213ff000 > > > > > I/O window 0: 00004800-000048ff > > > > > I/O window 1: 00004c00-00004cff > > > > > BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ > > > > > PostWrite+ 16-bit legacy interface ports at 0001 > > > > > > > > > > 0000:02:01.0 Ethernet controller: Intel Corp. 82540EP Gigabit > > > > > Ethernet Controller (Mobile) (rev 03) > > > > > Subsystem: IBM PRO/1000 MT Mobile Connection > > > > > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- > > > > > ParErr- Stepping- SERR+ FastB2B- > > > > > Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium > > > > > >TAbort- <TAbort- <MAbort- >SERR- <PERR- > > > > > Latency: 64 (63750ns min), Cache Line Size: 0x08 (32 bytes) > > > > > Interrupt: pin A routed to IRQ 9 > > > > > Region 0: Memory at c0220000 (32-bit, non-prefetchable) > > > > > Region 1: Memory at c0200000 (32-bit, non-prefetchable) > > > > > [size=64K] Region 2: I/O ports at 8000 [size=64] > > > > > Capabilities: [dc] Power Management version 2 > > > > > Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA > > > > > PME(D0+,D1-,D2-,D3hot+,D3cold+) > > > > > Status: D0 PME-Enable- DSel=0 DScale=1 PME- > > > > > Capabilities: [f0] Message Signalled Interrupts: 64bit+ > > > > > Queue=0/0 Enable- > > > > > Address: 0000000000000000 Data: 0000 > > > > > > > > > > 0000:02:02.0 Ethernet controller: Atheros Communications, Inc. AR5211 > > > > > 802.11ab NIC (rev 01) > > > > > Subsystem: Unknown device 17ab:8310 > > > > > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- > > > > > ParErr- Stepping- SERR+ FastB2B- > > > > > Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium > > > > > >TAbort- <TAbort- <MAbort- >SERR- <PERR- > > > > > Latency: 80 (2500ns min, 7000ns max), Cache Line Size: 0x08 > > > > > (32 bytes) Interrupt: pin A routed to IRQ 11 > > > > > Region 0: Memory at c0210000 (32-bit, non-prefetchable) > > > > > Capabilities: [44] Power Management version 2 > > > > > Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA > > > > > PME(D0-,D1-,D2-,D3hot-,D3cold-) > > > > > Status: D0 PME-Enable- DSel=0 DScale=2 PME- > > > > > > > > > > dmesges attached. > > > > > > > > > > regards > > > > > Alex > > > > > > > > > > Am Montag, 21. Juni 2004 19:50 schrieb Alexander Gran: > > > > > > Hi, > > > > > > > > > > > > just a quick note: > > > > > > Since 2.6.7-mm1 acpi C3 works even with usb and radeon loaded. > > > > > > Great work! > > > > > > > > > > > > regards > > > > > > Alex > > - -- > Encrypted Mails welcome. > PGP-Key at http://zodiac.dnsalias.org/misc/pgpkey.asc | Key-ID: 0x6D7DD291 > -----BEGIN PGP SIGNATURE----- > Version: GnuPG v1.2.4 (GNU/Linux) > > iD8DBQFA3GoT/aHb+2190pERAlW2AJ446y3PzZY5u0LvxDxzHloiu6q0vgCgrt4K > St69aZvzniJF+yl1GTpRoKU= > =sptO > -----END PGP SIGNATURE----- > ^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: Linux 2.6.7-mm1, IBM T40p, ACPI C3 finally working. 2004-06-25 19:04 ` Adam Sulmicki @ 2004-06-25 19:29 ` William Lee Irwin III 0 siblings, 0 replies; 8+ messages in thread From: William Lee Irwin III @ 2004-06-25 19:29 UTC (permalink / raw) To: Adam Sulmicki; +Cc: Alexander Gran, linux-kernel, linux-thinkpad On Fri, Jun 25, 2004 at 03:04:50PM -0400, Adam Sulmicki wrote: > not every single patch, a _binary search_ of patches. try logical half of > mm2, see if it breaks, if not then try the other half. and so on > recursively. It sure would be nice if this could be done with mainline. -- wli ^ permalink raw reply [flat|nested] 8+ messages in thread
* Linux 2.6.7-mm1, IBM T40p, ACPI C3 finally working. @ 2004-06-21 18:05 Alexander Gran 0 siblings, 0 replies; 8+ messages in thread From: Alexander Gran @ 2004-06-21 18:05 UTC (permalink / raw) To: linux-kernel -----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi, just a quick note: Since 2.6.7-mm1 acpi C3 works even with usb and radeon loaded. Great work! regards Alex - -- Encrypted Mails welcome. PGP-Key at http://zodiac.dnsalias.org/misc/pgpkey.asc | Key-ID: 0x6D7DD291 -----BEGIN PGP SIGNATURE----- Version: GnuPG v1.2.4 (GNU/Linux) iD8DBQFA1yOA/aHb+2190pERAh2vAJ4vGrvKkfP41awfUXnY+lwCvImNIACgiFjL H9+Wv0d2besPqek8V7Dc2rg= =Wy+K -----END PGP SIGNATURE----- ^ permalink raw reply [flat|nested] 8+ messages in thread
end of thread, other threads:[~2004-06-25 19:30 UTC | newest]
Thread overview: 8+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
[not found] <200406211951.03333@zodiac.zodiac.dnsalias.org>
2004-06-25 2:06 ` Linux 2.6.7-mm1, IBM T40p, ACPI C3 finally working Alexander Gran
2004-06-25 2:51 ` Adam Sulmicki
2004-06-25 14:05 ` Alexander Gran
2004-06-25 17:30 ` Adam Sulmicki
2004-06-25 18:08 ` Alexander Gran
2004-06-25 19:04 ` Adam Sulmicki
2004-06-25 19:29 ` William Lee Irwin III
2004-06-21 18:05 Alexander Gran
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.