From: Marcelo Tosatti <marcelo.tosatti@cyclades.com>
To: Paul Mackerras <paulus@samba.org>
Cc: linux-ppc-embedded <linuxppc-embedded@ozlabs.org>
Subject: Re: [PATCH] add big endian version of ld_/st_ IO access macros and convert main 8xx code to use it
Date: Thu, 8 Sep 2005 16:34:55 -0300 [thread overview]
Message-ID: <20050908193455.GA5446@dmt.cnet> (raw)
In-Reply-To: <17183.48543.616634.628331@cargo.ozlabs.ibm.com>
On Thu, Sep 08, 2005 at 02:27:11PM +1000, Paul Mackerras wrote:
> Marcelo Tosatti writes:
>
> > eieio/isync are not required. There's no need to execute redudant
> > instructions and occupy kernel space.
>
> Given how long it takes to access I/O devices, I don't believe an
> extra instruction or two is going to make a measurable difference.
> Feel free to show me measurements proving me wrong, of course... :)
I will try to measure it later on and change out_/in_ macros as
suggested.
For now are there any objections against this? Otherwise I'll merge it.
There are a few more places which need conversion, plan to change them
later on also.
Thanks everyone.
diff --git a/arch/ppc/8xx_io/commproc.c b/arch/ppc/8xx_io/commproc.c
--- a/arch/ppc/8xx_io/commproc.c
+++ b/arch/ppc/8xx_io/commproc.c
@@ -73,7 +73,7 @@ cpm_mask_irq(unsigned int irq)
{
int cpm_vec = irq - CPM_IRQ_OFFSET;
- ((immap_t *)IMAP_ADDR)->im_cpic.cpic_cimr &= ~(1 << cpm_vec);
+ out_be32(&((immap_t *)IMAP_ADDR)->im_cpic.cpic_cimr, in_be32(&((immap_t *)IMAP_ADDR)->im_cpic.cpic_cimr) & ~(1 << cpm_vec));
}
static void
@@ -81,7 +81,7 @@ cpm_unmask_irq(unsigned int irq)
{
int cpm_vec = irq - CPM_IRQ_OFFSET;
- ((immap_t *)IMAP_ADDR)->im_cpic.cpic_cimr |= (1 << cpm_vec);
+ out_be32(&((immap_t *)IMAP_ADDR)->im_cpic.cpic_cimr, in_be32(&((immap_t *)IMAP_ADDR)->im_cpic.cpic_cimr) | (1 << cpm_vec));
}
static void
@@ -95,7 +95,7 @@ cpm_eoi(unsigned int irq)
{
int cpm_vec = irq - CPM_IRQ_OFFSET;
- ((immap_t *)IMAP_ADDR)->im_cpic.cpic_cisr = (1 << cpm_vec);
+ out_be32(&((immap_t *)IMAP_ADDR)->im_cpic.cpic_cisr, (1 << cpm_vec));
}
struct hw_interrupt_type cpm_pic = {
@@ -133,7 +133,7 @@ m8xx_cpm_reset(void)
* manual recommends it.
* Bit 25, FAM can also be set to use FEC aggressive mode (860T).
*/
- imp->im_siu_conf.sc_sdcr = 1;
+ out_be32(&imp->im_siu_conf.sc_sdcr, 1),
/* Reclaim the DP memory for our use. */
m8xx_cpm_dpinit();
@@ -178,10 +178,10 @@ cpm_interrupt_init(void)
/* Initialize the CPM interrupt controller.
*/
- ((immap_t *)IMAP_ADDR)->im_cpic.cpic_cicr =
+ out_be32(&((immap_t *)IMAP_ADDR)->im_cpic.cpic_cicr,
(CICR_SCD_SCC4 | CICR_SCC_SCC3 | CICR_SCB_SCC2 | CICR_SCA_SCC1) |
- ((CPM_INTERRUPT/2) << 13) | CICR_HP_MASK;
- ((immap_t *)IMAP_ADDR)->im_cpic.cpic_cimr = 0;
+ ((CPM_INTERRUPT/2) << 13) | CICR_HP_MASK);
+ out_be32(&((immap_t *)IMAP_ADDR)->im_cpic.cpic_cimr, 0);
/* install the CPM interrupt controller routines for the CPM
* interrupt vectors
@@ -198,7 +198,7 @@ cpm_interrupt_init(void)
if (setup_irq(CPM_IRQ_OFFSET + CPMVEC_ERROR, &cpm_error_irqaction))
panic("Could not allocate CPM error IRQ!");
- ((immap_t *)IMAP_ADDR)->im_cpic.cpic_cicr |= CICR_IEN;
+ out_be32(&((immap_t *)IMAP_ADDR)->im_cpic.cpic_cicr, in_be32(&((immap_t *)IMAP_ADDR)->im_cpic.cpic_cicr) | CICR_IEN);
}
/*
@@ -212,8 +212,8 @@ cpm_get_irq(struct pt_regs *regs)
/* Get the vector by setting the ACK bit and then reading
* the register.
*/
- ((volatile immap_t *)IMAP_ADDR)->im_cpic.cpic_civr = 1;
- cpm_vec = ((volatile immap_t *)IMAP_ADDR)->im_cpic.cpic_civr;
+ out_be16(&((volatile immap_t *)IMAP_ADDR)->im_cpic.cpic_civr, 1);
+ cpm_vec = in_be16(&((volatile immap_t *)IMAP_ADDR)->im_cpic.cpic_civr);
cpm_vec >>= 11;
return cpm_vec;
diff --git a/arch/ppc/syslib/m8xx_setup.c b/arch/ppc/syslib/m8xx_setup.c
--- a/arch/ppc/syslib/m8xx_setup.c
+++ b/arch/ppc/syslib/m8xx_setup.c
@@ -144,12 +144,12 @@ void __init m8xx_calibrate_decr(void)
int freq, fp, divisor;
/* Unlock the SCCR. */
- ((volatile immap_t *)IMAP_ADDR)->im_clkrstk.cark_sccrk = ~KAPWR_KEY;
- ((volatile immap_t *)IMAP_ADDR)->im_clkrstk.cark_sccrk = KAPWR_KEY;
+ out_be32(&((immap_t *)IMAP_ADDR)->im_clkrstk.cark_sccrk, ~KAPWR_KEY);
+ out_be32(&((immap_t *)IMAP_ADDR)->im_clkrstk.cark_sccrk, KAPWR_KEY);
/* Force all 8xx processors to use divide by 16 processor clock. */
- ((volatile immap_t *)IMAP_ADDR)->im_clkrst.car_sccr |= 0x02000000;
-
+ out_be32(&((immap_t *)IMAP_ADDR)->im_clkrst.car_sccr,
+ in_be32(&((immap_t *)IMAP_ADDR)->im_clkrst.car_sccr)|0x02000000);
/* Processor frequency is MHz.
* The value 'fp' is the number of decrementer ticks per second.
*/
@@ -175,28 +175,24 @@ void __init m8xx_calibrate_decr(void)
* we guarantee the registers are locked, then we unlock them
* for our use.
*/
- ((volatile immap_t *)IMAP_ADDR)->im_sitk.sitk_tbscrk = ~KAPWR_KEY;
- ((volatile immap_t *)IMAP_ADDR)->im_sitk.sitk_rtcsck = ~KAPWR_KEY;
- ((volatile immap_t *)IMAP_ADDR)->im_sitk.sitk_tbk = ~KAPWR_KEY;
- ((volatile immap_t *)IMAP_ADDR)->im_sitk.sitk_tbscrk = KAPWR_KEY;
- ((volatile immap_t *)IMAP_ADDR)->im_sitk.sitk_rtcsck = KAPWR_KEY;
- ((volatile immap_t *)IMAP_ADDR)->im_sitk.sitk_tbk = KAPWR_KEY;
+ out_be32(&((immap_t *)IMAP_ADDR)->im_sitk.sitk_tbscrk, ~KAPWR_KEY);
+ out_be32(&((immap_t *)IMAP_ADDR)->im_sitk.sitk_rtcsck, ~KAPWR_KEY);
+ out_be32(&((immap_t *)IMAP_ADDR)->im_sitk.sitk_tbk, ~KAPWR_KEY);
+ out_be32(&((immap_t *)IMAP_ADDR)->im_sitk.sitk_tbscrk, KAPWR_KEY);
+ out_be32(&((immap_t *)IMAP_ADDR)->im_sitk.sitk_rtcsck, KAPWR_KEY);
+ out_be32(&((immap_t *)IMAP_ADDR)->im_sitk.sitk_tbk, KAPWR_KEY);
/* Disable the RTC one second and alarm interrupts. */
- ((volatile immap_t *)IMAP_ADDR)->im_sit.sit_rtcsc &=
- ~(RTCSC_SIE | RTCSC_ALE);
+ out_be16(&((immap_t *)IMAP_ADDR)->im_sit.sit_rtcsc, in_be16(&((immap_t *)IMAP_ADDR)->im_sit.sit_rtcsc) & ~(RTCSC_SIE | RTCSC_ALE));
/* Enable the RTC */
- ((volatile immap_t *)IMAP_ADDR)->im_sit.sit_rtcsc |=
- (RTCSC_RTF | RTCSC_RTE);
+ out_be16(&((immap_t *)IMAP_ADDR)->im_sit.sit_rtcsc, in_be16(&((immap_t *)IMAP_ADDR)->im_sit.sit_rtcsc) | (RTCSC_RTF | RTCSC_RTE));
/* Enabling the decrementer also enables the timebase interrupts
* (or from the other point of view, to get decrementer interrupts
* we have to enable the timebase). The decrementer interrupt
* is wired into the vector table, nothing to do here for that.
*/
- ((volatile immap_t *)IMAP_ADDR)->im_sit.sit_tbscr =
- ((mk_int_int_mask(DEC_INTERRUPT) << 8) |
- (TBSCR_TBF | TBSCR_TBE));
+ out_be16(&((immap_t *)IMAP_ADDR)->im_sit.sit_tbscr, (mk_int_int_mask(DEC_INTERRUPT) << 8) | (TBSCR_TBF | TBSCR_TBE));
if (setup_irq(DEC_INTERRUPT, &tbint_irqaction))
panic("Could not allocate timer IRQ!");
@@ -216,9 +212,9 @@ void __init m8xx_calibrate_decr(void)
static int
m8xx_set_rtc_time(unsigned long time)
{
- ((volatile immap_t *)IMAP_ADDR)->im_sitk.sitk_rtck = KAPWR_KEY;
- ((volatile immap_t *)IMAP_ADDR)->im_sit.sit_rtc = time;
- ((volatile immap_t *)IMAP_ADDR)->im_sitk.sitk_rtck = ~KAPWR_KEY;
+ out_be32(&((immap_t *)IMAP_ADDR)->im_sitk.sitk_rtck, KAPWR_KEY);
+ out_be32(&((immap_t *)IMAP_ADDR)->im_sit.sit_rtc, time);
+ out_be32(&((immap_t *)IMAP_ADDR)->im_sitk.sitk_rtck, ~KAPWR_KEY);
return(0);
}
@@ -226,7 +222,7 @@ static unsigned long
m8xx_get_rtc_time(void)
{
/* Get time from the RTC. */
- return((unsigned long)(((immap_t *)IMAP_ADDR)->im_sit.sit_rtc));
+ return (unsigned long) in_be32(&((immap_t *)IMAP_ADDR)->im_sit.sit_rtc);
}
static void
@@ -235,13 +231,13 @@ m8xx_restart(char *cmd)
__volatile__ unsigned char dummy;
local_irq_disable();
- ((immap_t *)IMAP_ADDR)->im_clkrst.car_plprcr |= 0x00000080;
+ out_be32(&((immap_t *)IMAP_ADDR)->im_clkrst.car_plprcr, in_be32(&((immap_t *)IMAP_ADDR)->im_clkrst.car_plprcr) | 0x00000080);
/* Clear the ME bit in MSR to cause checkstop on machine check
*/
mtmsr(mfmsr() & ~0x1000);
- dummy = ((immap_t *)IMAP_ADDR)->im_clkrst.res[0];
+ dummy = in_8(&((immap_t *)IMAP_ADDR)->im_clkrst.res[0]);
printk("Restart failed\n");
while(1);
}
@@ -306,8 +302,7 @@ m8xx_init_IRQ(void)
i8259_init(0);
/* The i8259 cascade interrupt must be level sensitive. */
- ((immap_t *)IMAP_ADDR)->im_siu_conf.sc_siel &=
- ~(0x80000000 >> ISA_BRIDGE_INT);
+ out_be32(&((immap_t *)IMAP_ADDR)->im_siu_conf.sc_siel, in_be32(&((immap_t *)IMAP_ADDR)->im_siu_conf.sc_siel & ~(0x80000000 >> ISA_BRIDGE_INT)));
if (setup_irq(ISA_BRIDGE_INT, &mbx_i8259_irqaction))
enable_irq(ISA_BRIDGE_INT);
diff --git a/arch/ppc/syslib/m8xx_wdt.c b/arch/ppc/syslib/m8xx_wdt.c
--- a/arch/ppc/syslib/m8xx_wdt.c
+++ b/arch/ppc/syslib/m8xx_wdt.c
@@ -29,8 +29,8 @@ void m8xx_wdt_reset(void)
{
volatile immap_t *imap = (volatile immap_t *)IMAP_ADDR;
- imap->im_siu_conf.sc_swsr = 0x556c; /* write magic1 */
- imap->im_siu_conf.sc_swsr = 0xaa39; /* write magic2 */
+ out_be16(imap->im_siu_conf.sc_swsr, 0x556c); /* write magic1 */
+ out_be16(imap->im_siu_conf.sc_swsr, 0xaa39); /* write magic2 */
}
static irqreturn_t m8xx_wdt_interrupt(int irq, void *dev, struct pt_regs *regs)
@@ -39,7 +39,7 @@ static irqreturn_t m8xx_wdt_interrupt(in
m8xx_wdt_reset();
- imap->im_sit.sit_piscr |= PISCR_PS; /* clear irq */
+ out_be16(imap->im_sit.sit_piscr, in_be16(imap->im_sit.sit_piscr | PISCR_PS)); /* clear irq */
return IRQ_HANDLED;
}
@@ -51,7 +51,7 @@ void __init m8xx_wdt_handler_install(bd_
u32 sypcr;
u32 pitrtclk;
- sypcr = imap->im_siu_conf.sc_sypcr;
+ sypcr = in_be32(imap->im_siu_conf.sc_sypcr);
irch/ppc/syslib/ppc8xx_pic.c:32:f (!(sypcr & 0x04)) {
printk(KERN_NOTICE "m8xx_wdt: wdt disabled (SYPCR: 0x%08X)\n",
@@ -87,9 +87,9 @@ void __init m8xx_wdt_handler_install(bd_
else
pitc = pitrtclk * wdt_timeout / binfo->bi_intfreq / 2;
- imap->im_sit.sit_pitc = pitc << 16;
- imap->im_sit.sit_piscr =
- (mk_int_int_mask(PIT_INTERRUPT) << 8) | PISCR_PIE | PISCR_PTE;
+ out_be32(imap->im_sit.sit_pitc, pitc << 16);
+
+ out_be16(imap->im_sit.sit_piscr, (mk_int_int_mask(PIT_INTERRUPT) << 8) | PISCR_PIE | PISCR_PTE);
if (setup_irq(PIT_INTERRUPT, &m8xx_wdt_irqaction))
panic("m8xx_wdt: error setting up the watchdog irq!");
diff --git a/arch/ppc/syslib/ppc8xx_pic.c b/arch/ppc/syslib/ppc8xx_pic.c
--- a/arch/ppc/syslib/ppc8xx_pic.c
+++ b/arch/ppc/syslib/ppc8xx_pic.c
@@ -6,6 +6,7 @@
#include <linux/signal.h>
#include <linux/interrupt.h>
#include <asm/irq.h>
+#include <asm/io.h>
#include <asm/8xx_immap.h>
#include <asm/mpc8xx.h>
#include "ppc8xx_pic.h"
@@ -29,8 +30,7 @@ static void m8xx_mask_irq(unsigned int i
word = irq_nr >> 5;
ppc_cached_irq_mask[word] &= ~(1 << (31-bit));
- ((immap_t *)IMAP_ADDR)->im_siu_conf.sc_simask =
- ppc_cached_irq_mask[word];
+ out_be32(&((immap_t *)IMAP_ADDR)->im_siu_conf.sc_simask, ppc_cached_irq_mask[word]);
}
static void m8xx_unmask_irq(unsigned int irq_nr)
@@ -41,8 +41,7 @@ static void m8xx_unmask_irq(unsigned int
word = irq_nr >> 5;
ppc_cached_irq_mask[word] |= (1 << (31-bit));
- ((immap_t *)IMAP_ADDR)->im_siu_conf.sc_simask =
- ppc_cached_irq_mask[word];
+ out_be32(&((immap_t *)IMAP_ADDR)->im_siu_conf.sc_simask, ppc_cached_irq_mask[word]);
}
static void m8xx_end_irq(unsigned int irq_nr)
@@ -55,8 +54,7 @@ static void m8xx_end_irq(unsigned int ir
word = irq_nr >> 5;
ppc_cached_irq_mask[word] |= (1 << (31-bit));
- ((immap_t *)IMAP_ADDR)->im_siu_conf.sc_simask =
- ppc_cached_irq_mask[word];
+ out_be32(&((immap_t *)IMAP_ADDR)->im_siu_conf.sc_simask, ppc_cached_irq_mask[word]);
}
}
@@ -69,9 +67,8 @@ static void m8xx_mask_and_ack(unsigned i
word = irq_nr >> 5;
ppc_cached_irq_mask[word] &= ~(1 << (31-bit));
- ((immap_t *)IMAP_ADDR)->im_siu_conf.sc_simask =
- ppc_cached_irq_mask[word];
- ((immap_t *)IMAP_ADDR)->im_siu_conf.sc_sipend = 1 << (31-bit);
+ out_be32(&((immap_t *)IMAP_ADDR)->im_siu_conf.sc_simask, ppc_cached_irq_mask[word]);
+ out_be32(&((immap_t *)IMAP_ADDR)->im_siu_conf.sc_sipend, 1 << (31-bit));
}
struct hw_interrupt_type ppc8xx_pic = {
@@ -93,7 +90,7 @@ m8xx_get_irq(struct pt_regs *regs)
/* For MPC8xx, read the SIVEC register and shift the bits down
* to get the irq number.
*/
- irq = ((immap_t *)IMAP_ADDR)->im_siu_conf.sc_sivec >> 26;
+ irq = in_be32(&((immap_t *)IMAP_ADDR)->im_siu_conf.sc_sivec) >> 26;
/*
* When we read the sivec without an interrupt to process, we will
next prev parent reply other threads:[~2005-09-08 19:40 UTC|newest]
Thread overview: 10+ messages / expand[flat|nested] mbox.gz Atom feed top
2005-09-07 23:03 [PATCH] add big endian version of ld_/st_ IO access macros and convert main 8xx code to use it Marcelo Tosatti
2005-09-08 0:28 ` Benjamin Herrenschmidt
2005-09-08 0:42 ` Dan Malek
2005-09-08 0:55 ` Benjamin Herrenschmidt
2005-09-08 0:58 ` Marcelo Tosatti
2005-09-08 4:27 ` Paul Mackerras
2005-09-08 13:56 ` Dan Malek
2005-09-08 19:34 ` Marcelo Tosatti [this message]
2005-09-08 0:51 ` Marcelo Tosatti
2005-09-08 1:14 ` Benjamin Herrenschmidt
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20050908193455.GA5446@dmt.cnet \
--to=marcelo.tosatti@cyclades.com \
--cc=linuxppc-embedded@ozlabs.org \
--cc=paulus@samba.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.