From: "Kok, Auke" <auke-jan.h.kok@intel.com>
To: "Garzik, Jeff" <jgarzik@pobox.com>
Cc: netdev@vger.kernel.org, "Brandeburg,
Jesse" <jesse.brandeburg@intel.com>,
"Kok, Auke" <auke-jan.h.kok@intel.com>,
"Kok, Auke" <auke@foo-projects.org>,
"Ronciak, John" <john.ronciak@intel.com>
Subject: [PATCH 17/21] e1000: add ich8lan core functions
Date: Wed, 21 Jun 2006 22:20:44 -0700 [thread overview]
Message-ID: <20060622052043.25497.85145.stgit@gitlost.site> (raw)
In-Reply-To: <20060622051815.25497.89192.stgit@gitlost.site>
This implements the core new functions needed for ich8's internal
NIC. This includes:
* ich8 specific read/write code
* flash/nvm access code
* software semaphore flag functions
* 10/100 PHY (fe - no gigabit speed) support for low-end versions
* A workaround for a powerdown sequence problem discovered that
affects a small number of motherboard.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
---
drivers/net/e1000/e1000_hw.c | 1000 +++++++++++++++++++++++++++++++++++++++
drivers/net/e1000/e1000_hw.h | 386 +++++++++++++++
drivers/net/e1000/e1000_osdep.h | 13 +
3 files changed, 1392 insertions(+), 7 deletions(-)
diff --git a/drivers/net/e1000/e1000_hw.c b/drivers/net/e1000/e1000_hw.c
index 784f950..a3f5ccd 100644
--- a/drivers/net/e1000/e1000_hw.c
+++ b/drivers/net/e1000/e1000_hw.c
@@ -3617,11 +3617,120 @@ e1000_phy_reset(struct e1000_hw *hw)
}
/******************************************************************************
+* Work-around for 82566 power-down: on D3 entry-
+* 1) disable gigabit link
+* 2) write VR power-down enable
+* 3) read it back
+* if successful continue, else issue LCD reset and repeat
+*
+* hw - struct containing variables accessed by shared code
+******************************************************************************/
+void
+e1000_phy_powerdown_workaround(struct e1000_hw *hw)
+{
+ int32_t reg;
+ uint16_t phy_data;
+ int32_t retry = 0;
+
+ DEBUGFUNC("e1000_phy_powerdown_workaround");
+
+ if (hw->phy_type != e1000_phy_igp_3)
+ return;
+
+ do {
+ /* Disable link */
+ reg = E1000_READ_REG(hw, PHY_CTRL);
+ E1000_WRITE_REG(hw, PHY_CTRL, reg | E1000_PHY_CTRL_GBE_DISABLE |
+ E1000_PHY_CTRL_NOND0A_GBE_DISABLE);
+
+ /* Write VR power-down enable */
+ e1000_read_phy_reg(hw, IGP3_VR_CTRL, &phy_data);
+ e1000_write_phy_reg(hw, IGP3_VR_CTRL, phy_data |
+ IGP3_VR_CTRL_MODE_SHUT);
+
+ /* Read it back and test */
+ e1000_read_phy_reg(hw, IGP3_VR_CTRL, &phy_data);
+ if ((phy_data & IGP3_VR_CTRL_MODE_SHUT) || retry)
+ break;
+
+ /* Issue PHY reset and repeat at most one more time */
+ reg = E1000_READ_REG(hw, CTRL);
+ E1000_WRITE_REG(hw, CTRL, reg | E1000_CTRL_PHY_RST);
+ retry++;
+ } while (retry);
+
+ return;
+
+}
+
+/******************************************************************************
+* Work-around for 82566 Kumeran PCS lock loss:
+* On link status change (i.e. PCI reset, speed change) and link is up and
+* speed is gigabit-
+* 0) if workaround is optionally disabled do nothing
+* 1) wait 1ms for Kumeran link to come up
+* 2) check Kumeran Diagnostic register PCS lock loss bit
+* 3) if not set the link is locked (all is good), otherwise...
+* 4) reset the PHY
+* 5) repeat up to 10 times
+* Note: this is only called for IGP3 copper when speed is 1gb.
+*
+* hw - struct containing variables accessed by shared code
+******************************************************************************/
+int32_t
+e1000_kumeran_lock_loss_workaround(struct e1000_hw *hw)
+{
+ int32_t ret_val;
+ int32_t reg;
+ int32_t cnt;
+ uint16_t phy_data;
+
+ if (hw->kmrn_lock_loss_workaround_disabled)
+ return E1000_SUCCESS;
+
+ /* Make sure link is up before proceeding. If not just return.
+ * Attempting this while link is negotiating fouls up link
+ * stability */
+ ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data);
+ ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data);
+
+ if (phy_data & MII_SR_LINK_STATUS) {
+ for (cnt = 0; cnt < 10; cnt++) {
+ /* read once to clear */
+ ret_val = e1000_read_phy_reg(hw, IGP3_KMRN_DIAG, &phy_data);
+ if (ret_val)
+ return ret_val;
+ /* and again to get new status */
+ ret_val = e1000_read_phy_reg(hw, IGP3_KMRN_DIAG, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ /* check for PCS lock */
+ if (!(phy_data & IGP3_KMRN_DIAG_PCS_LOCK_LOSS))
+ return E1000_SUCCESS;
+
+ /* Issue PHY reset */
+ e1000_phy_hw_reset(hw);
+ msec_delay_irq(5);
+ }
+ /* Disable GigE link negotiation */
+ reg = E1000_READ_REG(hw, PHY_CTRL);
+ E1000_WRITE_REG(hw, PHY_CTRL, reg | E1000_PHY_CTRL_GBE_DISABLE |
+ E1000_PHY_CTRL_NOND0A_GBE_DISABLE);
+
+ /* unable to acquire PCS lock */
+ return E1000_ERR_PHY;
+ }
+
+ return E1000_SUCCESS;
+}
+
+/******************************************************************************
* Probes the expected PHY address for known PHY IDs
*
* hw - Struct containing variables accessed by shared code
******************************************************************************/
-static int32_t
+int32_t
e1000_detect_gig_phy(struct e1000_hw *hw)
{
int32_t phy_init_status, ret_val;
@@ -3804,6 +3913,53 @@ e1000_phy_igp_get_info(struct e1000_hw *
}
/******************************************************************************
+* Get PHY information from various PHY registers for ife PHY only.
+*
+* hw - Struct containing variables accessed by shared code
+* phy_info - PHY information structure
+******************************************************************************/
+int32_t
+e1000_phy_ife_get_info(struct e1000_hw *hw,
+ struct e1000_phy_info *phy_info)
+{
+ int32_t ret_val;
+ uint16_t phy_data, polarity;
+
+ DEBUGFUNC("e1000_phy_ife_get_info");
+
+ phy_info->downshift = (e1000_downshift)hw->speed_downgraded;
+ phy_info->extended_10bt_distance = e1000_10bt_ext_dist_enable_normal;
+
+ ret_val = e1000_read_phy_reg(hw, IFE_PHY_SPECIAL_CONTROL, &phy_data);
+ if (ret_val)
+ return ret_val;
+ phy_info->polarity_correction =
+ (phy_data & IFE_PSC_AUTO_POLARITY_DISABLE) >>
+ IFE_PSC_AUTO_POLARITY_DISABLE_SHIFT;
+
+ if (phy_info->polarity_correction == e1000_polarity_reversal_enabled) {
+ ret_val = e1000_check_polarity(hw, &polarity);
+ if (ret_val)
+ return ret_val;
+ } else {
+ /* Polarity is forced. */
+ polarity = (phy_data & IFE_PSC_FORCE_POLARITY) >>
+ IFE_PSC_FORCE_POLARITY_SHIFT;
+ }
+ phy_info->cable_polarity = polarity;
+
+ ret_val = e1000_read_phy_reg(hw, IFE_PHY_MDIX_CONTROL, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ phy_info->mdix_mode =
+ (phy_data & (IFE_PMC_AUTO_MDIX | IFE_PMC_FORCE_MDIX)) >>
+ IFE_PMC_MDIX_MODE_SHIFT;
+
+ return E1000_SUCCESS;
+}
+
+/******************************************************************************
* Get PHY information from various PHY registers fot m88 PHY only.
*
* hw - Struct containing variables accessed by shared code
@@ -7630,4 +7786,846 @@ e1000_arc_subsystem_valid(struct e1000_h
}
+/******************************************************************************
+ * Configure PCI-Ex no-snoop
+ *
+ * hw - Struct containing variables accessed by shared code.
+ * no_snoop - Bitmap of no-snoop events.
+ *
+ * returns: E1000_SUCCESS
+ *
+ *****************************************************************************/
+int32_t
+e1000_set_pci_ex_no_snoop(struct e1000_hw *hw, uint32_t no_snoop)
+{
+ uint32_t gcr_reg = 0;
+
+ DEBUGFUNC("e1000_set_pci_ex_no_snoop");
+
+ if (hw->bus_type == e1000_bus_type_unknown)
+ e1000_get_bus_info(hw);
+
+ if (hw->bus_type != e1000_bus_type_pci_express)
+ return E1000_SUCCESS;
+
+ if (no_snoop) {
+ gcr_reg = E1000_READ_REG(hw, GCR);
+ gcr_reg &= ~(PCI_EX_NO_SNOOP_ALL);
+ gcr_reg |= no_snoop;
+ E1000_WRITE_REG(hw, GCR, gcr_reg);
+ }
+ if (hw->mac_type == e1000_ich8lan) {
+ uint32_t ctrl_ext;
+
+ E1000_WRITE_REG(hw, GCR, PCI_EX_82566_SNOOP_ALL);
+
+ ctrl_ext = E1000_READ_REG(hw, CTRL_EXT);
+ ctrl_ext |= E1000_CTRL_EXT_RO_DIS;
+ E1000_WRITE_REG(hw, CTRL_EXT, ctrl_ext);
+ }
+
+ return E1000_SUCCESS;
+}
+
+/***************************************************************************
+ *
+ * Get software semaphore FLAG bit (SWFLAG).
+ * SWFLAG is used to synchronize the access to all shared resource between
+ * SW, FW and HW.
+ *
+ * hw: Struct containing variables accessed by shared code
+ *
+ ***************************************************************************/
+int32_t
+e1000_get_software_flag(struct e1000_hw *hw)
+{
+ int32_t timeout = PHY_CFG_TIMEOUT;
+ uint32_t extcnf_ctrl;
+
+ DEBUGFUNC("e1000_get_software_flag");
+
+ if (hw->mac_type == e1000_ich8lan) {
+ while (timeout) {
+ extcnf_ctrl = E1000_READ_REG(hw, EXTCNF_CTRL);
+ extcnf_ctrl |= E1000_EXTCNF_CTRL_SWFLAG;
+ E1000_WRITE_REG(hw, EXTCNF_CTRL, extcnf_ctrl);
+
+ extcnf_ctrl = E1000_READ_REG(hw, EXTCNF_CTRL);
+ if (extcnf_ctrl & E1000_EXTCNF_CTRL_SWFLAG)
+ break;
+ msec_delay_irq(1);
+ timeout--;
+ }
+
+ if (!timeout) {
+ DEBUGOUT("FW or HW locks the resource too long.\n");
+ return -E1000_ERR_CONFIG;
+ }
+ }
+
+ return E1000_SUCCESS;
+}
+
+/***************************************************************************
+ *
+ * Release software semaphore FLAG bit (SWFLAG).
+ * SWFLAG is used to synchronize the access to all shared resource between
+ * SW, FW and HW.
+ *
+ * hw: Struct containing variables accessed by shared code
+ *
+ ***************************************************************************/
+void
+e1000_release_software_flag(struct e1000_hw *hw)
+{
+ uint32_t extcnf_ctrl;
+
+ DEBUGFUNC("e1000_release_software_flag");
+
+ if (hw->mac_type == e1000_ich8lan) {
+ extcnf_ctrl= E1000_READ_REG(hw, EXTCNF_CTRL);
+ extcnf_ctrl &= ~E1000_EXTCNF_CTRL_SWFLAG;
+ E1000_WRITE_REG(hw, EXTCNF_CTRL, extcnf_ctrl);
+ }
+
+ return;
+}
+
+/***************************************************************************
+ *
+ * Disable dynamic power down mode in ife PHY.
+ * It can be used to workaround band-gap problem.
+ *
+ * hw: Struct containing variables accessed by shared code
+ *
+ ***************************************************************************/
+int32_t
+e1000_ife_disable_dynamic_power_down(struct e1000_hw *hw)
+{
+ uint16_t phy_data;
+ int32_t ret_val = E1000_SUCCESS;
+
+ DEBUGFUNC("e1000_ife_disable_dynamic_power_down");
+
+ if (hw->phy_type == e1000_phy_ife) {
+ ret_val = e1000_read_phy_reg(hw, IFE_PHY_SPECIAL_CONTROL, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ phy_data |= IFE_PSC_DISABLE_DYNAMIC_POWER_DOWN;
+ ret_val = e1000_write_phy_reg(hw, IFE_PHY_SPECIAL_CONTROL, phy_data);
+ }
+
+ return ret_val;
+}
+
+/***************************************************************************
+ *
+ * Enable dynamic power down mode in ife PHY.
+ * It can be used to workaround band-gap problem.
+ *
+ * hw: Struct containing variables accessed by shared code
+ *
+ ***************************************************************************/
+int32_t
+e1000_ife_enable_dynamic_power_down(struct e1000_hw *hw)
+{
+ uint16_t phy_data;
+ int32_t ret_val = E1000_SUCCESS;
+
+ DEBUGFUNC("e1000_ife_enable_dynamic_power_down");
+
+ if (hw->phy_type == e1000_phy_ife) {
+ ret_val = e1000_read_phy_reg(hw, IFE_PHY_SPECIAL_CONTROL, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ phy_data &= ~IFE_PSC_DISABLE_DYNAMIC_POWER_DOWN;
+ ret_val = e1000_write_phy_reg(hw, IFE_PHY_SPECIAL_CONTROL, phy_data);
+ }
+
+ return ret_val;
+}
+
+/******************************************************************************
+ * Reads a 16 bit word or words from the EEPROM using the ICH8's flash access
+ * register.
+ *
+ * hw - Struct containing variables accessed by shared code
+ * offset - offset of word in the EEPROM to read
+ * data - word read from the EEPROM
+ * words - number of words to read
+ *****************************************************************************/
+int32_t
+e1000_read_eeprom_ich8(struct e1000_hw *hw, uint16_t offset, uint16_t words,
+ uint16_t *data)
+{
+ int32_t error = E1000_SUCCESS;
+ uint32_t flash_bank = 0;
+ uint32_t act_offset = 0;
+ uint32_t bank_offset = 0;
+ uint16_t word = 0;
+ uint16_t i = 0;
+
+ /* We need to know which is the valid flash bank. In the event
+ * that we didn't allocate eeprom_shadow_ram, we may not be
+ * managing flash_bank. So it cannot be trusted and needs
+ * to be updated with each read.
+ */
+ /* Value of bit 22 corresponds to the flash bank we're on. */
+ flash_bank = (E1000_READ_REG(hw, EECD) & E1000_EECD_SEC1VAL) ? 1 : 0;
+
+ /* Adjust offset appropriately if we're on bank 1 - adjust for word size */
+ bank_offset = flash_bank * (hw->flash_bank_size * 2);
+
+ error = e1000_get_software_flag(hw);
+ if (error != E1000_SUCCESS)
+ return error;
+
+ for (i = 0; i < words; i++) {
+ if (hw->eeprom_shadow_ram != NULL &&
+ hw->eeprom_shadow_ram[offset+i].modified == TRUE) {
+ data[i] = hw->eeprom_shadow_ram[offset+i].eeprom_word;
+ } else {
+ /* The NVM part needs a byte offset, hence * 2 */
+ act_offset = bank_offset + ((offset + i) * 2);
+ error = e1000_read_ich8_word(hw, act_offset, &word);
+ if (error != E1000_SUCCESS)
+ break;
+ data[i] = word;
+ }
+ }
+
+ e1000_release_software_flag(hw);
+
+ return error;
+}
+
+/******************************************************************************
+ * Writes a 16 bit word or words to the EEPROM using the ICH8's flash access
+ * register. Actually, writes are written to the shadow ram cache in the hw
+ * structure hw->e1000_shadow_ram. e1000_commit_shadow_ram flushes this to
+ * the NVM, which occurs when the NVM checksum is updated.
+ *
+ * hw - Struct containing variables accessed by shared code
+ * offset - offset of word in the EEPROM to write
+ * words - number of words to write
+ * data - words to write to the EEPROM
+ *****************************************************************************/
+int32_t
+e1000_write_eeprom_ich8(struct e1000_hw *hw, uint16_t offset, uint16_t words,
+ uint16_t *data)
+{
+ uint32_t i = 0;
+ int32_t error = E1000_SUCCESS;
+
+ error = e1000_get_software_flag(hw);
+ if (error != E1000_SUCCESS)
+ return error;
+
+ /* A driver can write to the NVM only if it has eeprom_shadow_ram
+ * allocated. Subsequent reads to the modified words are read from
+ * this cached structure as well. Writes will only go into this
+ * cached structure unless it's followed by a call to
+ * e1000_update_eeprom_checksum() where it will commit the changes
+ * and clear the "modified" field.
+ */
+ if (hw->eeprom_shadow_ram != NULL) {
+ for (i = 0; i < words; i++) {
+ if ((offset + i) < E1000_SHADOW_RAM_WORDS) {
+ hw->eeprom_shadow_ram[offset+i].modified = TRUE;
+ hw->eeprom_shadow_ram[offset+i].eeprom_word = data[i];
+ } else {
+ error = -E1000_ERR_EEPROM;
+ break;
+ }
+ }
+ } else {
+ /* Drivers have the option to not allocate eeprom_shadow_ram as long
+ * as they don't perform any NVM writes. An attempt in doing so
+ * will result in this error.
+ */
+ error = -E1000_ERR_EEPROM;
+ }
+
+ e1000_release_software_flag(hw);
+
+ return error;
+}
+
+/******************************************************************************
+ * This function does initial flash setup so that a new read/write/erase cycle
+ * can be started.
+ *
+ * hw - The pointer to the hw structure
+ ****************************************************************************/
+int32_t
+e1000_ich8_cycle_init(struct e1000_hw *hw)
+{
+ union ich8_hws_flash_status hsfsts;
+ int32_t error = E1000_ERR_EEPROM;
+ int32_t i = 0;
+
+ DEBUGFUNC("e1000_ich8_cycle_init");
+
+ hsfsts.regval = E1000_READ_ICH8_REG16(hw, ICH8_FLASH_HSFSTS);
+
+ /* May be check the Flash Des Valid bit in Hw status */
+ if (hsfsts.hsf_status.fldesvalid == 0) {
+ DEBUGOUT("Flash descriptor invalid. SW Sequencing must be used.");
+ return error;
+ }
+
+ /* Clear FCERR in Hw status by writing 1 */
+ /* Clear DAEL in Hw status by writing a 1 */
+ hsfsts.hsf_status.flcerr = 1;
+ hsfsts.hsf_status.dael = 1;
+
+ E1000_WRITE_ICH8_REG16(hw, ICH8_FLASH_HSFSTS, hsfsts.regval);
+
+ /* Either we should have a hardware SPI cycle in progress bit to check
+ * against, in order to start a new cycle or FDONE bit should be changed
+ * in the hardware so that it is 1 after harware reset, which can then be
+ * used as an indication whether a cycle is in progress or has been
+ * completed .. we should also have some software semaphore mechanism to
+ * guard FDONE or the cycle in progress bit so that two threads access to
+ * those bits can be sequentiallized or a way so that 2 threads dont
+ * start the cycle at the same time */
+
+ if (hsfsts.hsf_status.flcinprog == 0) {
+ /* There is no cycle running at present, so we can start a cycle */
+ /* Begin by setting Flash Cycle Done. */
+ hsfsts.hsf_status.flcdone = 1;
+ E1000_WRITE_ICH8_REG16(hw, ICH8_FLASH_HSFSTS, hsfsts.regval);
+ error = E1000_SUCCESS;
+ } else {
+ /* otherwise poll for sometime so the current cycle has a chance
+ * to end before giving up. */
+ for (i = 0; i < ICH8_FLASH_COMMAND_TIMEOUT; i++) {
+ hsfsts.regval = E1000_READ_ICH8_REG16(hw, ICH8_FLASH_HSFSTS);
+ if (hsfsts.hsf_status.flcinprog == 0) {
+ error = E1000_SUCCESS;
+ break;
+ }
+ udelay(1);
+ }
+ if (error == E1000_SUCCESS) {
+ /* Successful in waiting for previous cycle to timeout,
+ * now set the Flash Cycle Done. */
+ hsfsts.hsf_status.flcdone = 1;
+ E1000_WRITE_ICH8_REG16(hw, ICH8_FLASH_HSFSTS, hsfsts.regval);
+ } else {
+ DEBUGOUT("Flash controller busy, cannot get access");
+ }
+ }
+ return error;
+}
+
+/******************************************************************************
+ * This function starts a flash cycle and waits for its completion
+ *
+ * hw - The pointer to the hw structure
+ ****************************************************************************/
+int32_t
+e1000_ich8_flash_cycle(struct e1000_hw *hw, uint32_t timeout)
+{
+ union ich8_hws_flash_ctrl hsflctl;
+ union ich8_hws_flash_status hsfsts;
+ int32_t error = E1000_ERR_EEPROM;
+ uint32_t i = 0;
+
+ /* Start a cycle by writing 1 in Flash Cycle Go in Hw Flash Control */
+ hsflctl.regval = E1000_READ_ICH8_REG16(hw, ICH8_FLASH_HSFCTL);
+ hsflctl.hsf_ctrl.flcgo = 1;
+ E1000_WRITE_ICH8_REG16(hw, ICH8_FLASH_HSFCTL, hsflctl.regval);
+
+ /* wait till FDONE bit is set to 1 */
+ do {
+ hsfsts.regval = E1000_READ_ICH8_REG16(hw, ICH8_FLASH_HSFSTS);
+ if (hsfsts.hsf_status.flcdone == 1)
+ break;
+ udelay(1);
+ i++;
+ } while (i < timeout);
+ if (hsfsts.hsf_status.flcdone == 1 && hsfsts.hsf_status.flcerr == 0) {
+ error = E1000_SUCCESS;
+ }
+ return error;
+}
+
+/******************************************************************************
+ * Reads a byte or word from the NVM using the ICH8 flash access registers.
+ *
+ * hw - The pointer to the hw structure
+ * index - The index of the byte or word to read.
+ * size - Size of data to read, 1=byte 2=word
+ * data - Pointer to the word to store the value read.
+ *****************************************************************************/
+int32_t
+e1000_read_ich8_data(struct e1000_hw *hw, uint32_t index,
+ uint32_t size, uint16_t* data)
+{
+ union ich8_hws_flash_status hsfsts;
+ union ich8_hws_flash_ctrl hsflctl;
+ uint32_t flash_linear_address;
+ uint32_t flash_data = 0;
+ int32_t error = -E1000_ERR_EEPROM;
+ int32_t count = 0;
+
+ DEBUGFUNC("e1000_read_ich8_data");
+
+ if (size < 1 || size > 2 || data == 0x0 ||
+ index > ICH8_FLASH_LINEAR_ADDR_MASK)
+ return error;
+
+ flash_linear_address = (ICH8_FLASH_LINEAR_ADDR_MASK & index) +
+ hw->flash_base_addr;
+
+ do {
+ udelay(1);
+ /* Steps */
+ error = e1000_ich8_cycle_init(hw);
+ if (error != E1000_SUCCESS)
+ break;
+
+ hsflctl.regval = E1000_READ_ICH8_REG16(hw, ICH8_FLASH_HSFCTL);
+ /* 0b/1b corresponds to 1 or 2 byte size, respectively. */
+ hsflctl.hsf_ctrl.fldbcount = size - 1;
+ hsflctl.hsf_ctrl.flcycle = ICH8_CYCLE_READ;
+ E1000_WRITE_ICH8_REG16(hw, ICH8_FLASH_HSFCTL, hsflctl.regval);
+
+ /* Write the last 24 bits of index into Flash Linear address field in
+ * Flash Address */
+ /* TODO: TBD maybe check the index against the size of flash */
+
+ E1000_WRITE_ICH8_REG(hw, ICH8_FLASH_FADDR, flash_linear_address);
+
+ error = e1000_ich8_flash_cycle(hw, ICH8_FLASH_COMMAND_TIMEOUT);
+
+ /* Check if FCERR is set to 1, if set to 1, clear it and try the whole
+ * sequence a few more times, else read in (shift in) the Flash Data0,
+ * the order is least significant byte first msb to lsb */
+ if (error == E1000_SUCCESS) {
+ flash_data = E1000_READ_ICH8_REG(hw, ICH8_FLASH_FDATA0);
+ if (size == 1) {
+ *data = (uint8_t)(flash_data & 0x000000FF);
+ } else if (size == 2) {
+ *data = (uint16_t)(flash_data & 0x0000FFFF);
+ }
+ break;
+ } else {
+ /* If we've gotten here, then things are probably completely hosed,
+ * but if the error condition is detected, it won't hurt to give
+ * it another try...ICH8_FLASH_CYCLE_REPEAT_COUNT times.
+ */
+ hsfsts.regval = E1000_READ_ICH8_REG16(hw, ICH8_FLASH_HSFSTS);
+ if (hsfsts.hsf_status.flcerr == 1) {
+ /* Repeat for some time before giving up. */
+ continue;
+ } else if (hsfsts.hsf_status.flcdone == 0) {
+ DEBUGOUT("Timeout error - flash cycle did not complete.");
+ break;
+ }
+ }
+ } while (count++ < ICH8_FLASH_CYCLE_REPEAT_COUNT);
+
+ return error;
+}
+
+/******************************************************************************
+ * Writes One /two bytes to the NVM using the ICH8 flash access registers.
+ *
+ * hw - The pointer to the hw structure
+ * index - The index of the byte/word to read.
+ * size - Size of data to read, 1=byte 2=word
+ * data - The byte(s) to write to the NVM.
+ *****************************************************************************/
+int32_t
+e1000_write_ich8_data(struct e1000_hw *hw, uint32_t index, uint32_t size,
+ uint16_t data)
+{
+ union ich8_hws_flash_status hsfsts;
+ union ich8_hws_flash_ctrl hsflctl;
+ uint32_t flash_linear_address;
+ uint32_t flash_data = 0;
+ int32_t error = -E1000_ERR_EEPROM;
+ int32_t count = 0;
+
+ DEBUGFUNC("e1000_write_ich8_data");
+
+ if (size < 1 || size > 2 || data > size * 0xff ||
+ index > ICH8_FLASH_LINEAR_ADDR_MASK)
+ return error;
+
+ flash_linear_address = (ICH8_FLASH_LINEAR_ADDR_MASK & index) +
+ hw->flash_base_addr;
+
+ do {
+ udelay(1);
+ /* Steps */
+ error = e1000_ich8_cycle_init(hw);
+ if (error != E1000_SUCCESS)
+ break;
+
+ hsflctl.regval = E1000_READ_ICH8_REG16(hw, ICH8_FLASH_HSFCTL);
+ /* 0b/1b corresponds to 1 or 2 byte size, respectively. */
+ hsflctl.hsf_ctrl.fldbcount = size -1;
+ hsflctl.hsf_ctrl.flcycle = ICH8_CYCLE_WRITE;
+ E1000_WRITE_ICH8_REG16(hw, ICH8_FLASH_HSFCTL, hsflctl.regval);
+
+ /* Write the last 24 bits of index into Flash Linear address field in
+ * Flash Address */
+ E1000_WRITE_ICH8_REG(hw, ICH8_FLASH_FADDR, flash_linear_address);
+
+ if (size == 1)
+ flash_data = (uint32_t)data & 0x00FF;
+ else
+ flash_data = (uint32_t)data;
+
+ E1000_WRITE_ICH8_REG(hw, ICH8_FLASH_FDATA0, flash_data);
+
+ /* check if FCERR is set to 1 , if set to 1, clear it and try the whole
+ * sequence a few more times else done */
+ error = e1000_ich8_flash_cycle(hw, ICH8_FLASH_COMMAND_TIMEOUT);
+ if (error == E1000_SUCCESS) {
+ break;
+ } else {
+ /* If we're here, then things are most likely completely hosed,
+ * but if the error condition is detected, it won't hurt to give
+ * it another try...ICH8_FLASH_CYCLE_REPEAT_COUNT times.
+ */
+ hsfsts.regval = E1000_READ_ICH8_REG16(hw, ICH8_FLASH_HSFSTS);
+ if (hsfsts.hsf_status.flcerr == 1) {
+ /* Repeat for some time before giving up. */
+ continue;
+ } else if (hsfsts.hsf_status.flcdone == 0) {
+ DEBUGOUT("Timeout error - flash cycle did not complete.");
+ break;
+ }
+ }
+ } while (count++ < ICH8_FLASH_CYCLE_REPEAT_COUNT);
+
+ return error;
+}
+
+/******************************************************************************
+ * Reads a single byte from the NVM using the ICH8 flash access registers.
+ *
+ * hw - pointer to e1000_hw structure
+ * index - The index of the byte to read.
+ * data - Pointer to a byte to store the value read.
+ *****************************************************************************/
+int32_t
+e1000_read_ich8_byte(struct e1000_hw *hw, uint32_t index, uint8_t* data)
+{
+ int32_t status = E1000_SUCCESS;
+ uint16_t word = 0;
+
+ status = e1000_read_ich8_data(hw, index, 1, &word);
+ if (status == E1000_SUCCESS) {
+ *data = (uint8_t)word;
+ }
+
+ return status;
+}
+
+/******************************************************************************
+ * Writes a single byte to the NVM using the ICH8 flash access registers.
+ * Performs verification by reading back the value and then going through
+ * a retry algorithm before giving up.
+ *
+ * hw - pointer to e1000_hw structure
+ * index - The index of the byte to write.
+ * byte - The byte to write to the NVM.
+ *****************************************************************************/
+int32_t
+e1000_verify_write_ich8_byte(struct e1000_hw *hw, uint32_t index, uint8_t byte)
+{
+ int32_t error = E1000_SUCCESS;
+ int32_t program_retries;
+ uint8_t temp_byte;
+
+ e1000_write_ich8_byte(hw, index, byte);
+ udelay(100);
+
+ for (program_retries = 0; program_retries < 100; program_retries++) {
+ e1000_read_ich8_byte(hw, index, &temp_byte);
+ if (temp_byte == byte)
+ break;
+ udelay(10);
+ e1000_write_ich8_byte(hw, index, byte);
+ udelay(100);
+ }
+ if (program_retries == 100)
+ error = E1000_ERR_EEPROM;
+
+ return error;
+}
+
+/******************************************************************************
+ * Writes a single byte to the NVM using the ICH8 flash access registers.
+ *
+ * hw - pointer to e1000_hw structure
+ * index - The index of the byte to read.
+ * data - The byte to write to the NVM.
+ *****************************************************************************/
+int32_t
+e1000_write_ich8_byte(struct e1000_hw *hw, uint32_t index, uint8_t data)
+{
+ int32_t status = E1000_SUCCESS;
+ uint16_t word = (uint16_t)data;
+
+ status = e1000_write_ich8_data(hw, index, 1, word);
+
+ return status;
+}
+
+/******************************************************************************
+ * Reads a word from the NVM using the ICH8 flash access registers.
+ *
+ * hw - pointer to e1000_hw structure
+ * index - The starting byte index of the word to read.
+ * data - Pointer to a word to store the value read.
+ *****************************************************************************/
+int32_t
+e1000_read_ich8_word(struct e1000_hw *hw, uint32_t index, uint16_t *data)
+{
+ int32_t status = E1000_SUCCESS;
+ status = e1000_read_ich8_data(hw, index, 2, data);
+ return status;
+}
+
+/******************************************************************************
+ * Writes a word to the NVM using the ICH8 flash access registers.
+ *
+ * hw - pointer to e1000_hw structure
+ * index - The starting byte index of the word to read.
+ * data - The word to write to the NVM.
+ *****************************************************************************/
+int32_t
+e1000_write_ich8_word(struct e1000_hw *hw, uint32_t index, uint16_t data)
+{
+ int32_t status = E1000_SUCCESS;
+ status = e1000_write_ich8_data(hw, index, 2, data);
+ return status;
+}
+
+/******************************************************************************
+ * Erases the bank specified. Each bank is a 4k block. Segments are 0 based.
+ * segment N is 4096 * N + flash_reg_addr.
+ *
+ * hw - pointer to e1000_hw structure
+ * segment - 0 for first segment, 1 for second segment, etc.
+ *****************************************************************************/
+int32_t
+e1000_erase_ich8_4k_segment(struct e1000_hw *hw, uint32_t segment)
+{
+ union ich8_hws_flash_status hsfsts;
+ union ich8_hws_flash_ctrl hsflctl;
+ uint32_t flash_linear_address;
+ int32_t count = 0;
+ int32_t error = E1000_ERR_EEPROM;
+ int32_t iteration, seg_size;
+ int32_t sector_size;
+ int32_t j = 0;
+ int32_t error_flag = 0;
+
+ hsfsts.regval = E1000_READ_ICH8_REG16(hw, ICH8_FLASH_HSFSTS);
+
+ /* Determine HW Sector size: Read BERASE bits of Hw flash Status register */
+ /* 00: The Hw sector is 256 bytes, hence we need to erase 16
+ * consecutive sectors. The start index for the nth Hw sector can be
+ * calculated as = segment * 4096 + n * 256
+ * 01: The Hw sector is 4K bytes, hence we need to erase 1 sector.
+ * The start index for the nth Hw sector can be calculated
+ * as = segment * 4096
+ * 10: Error condition
+ * 11: The Hw sector size is much bigger than the size asked to
+ * erase...error condition */
+ if (hsfsts.hsf_status.berasesz == 0x0) {
+ /* Hw sector size 256 */
+ sector_size = seg_size = ICH8_FLASH_SEG_SIZE_256;
+ iteration = ICH8_FLASH_SECTOR_SIZE / ICH8_FLASH_SEG_SIZE_256;
+ } else if (hsfsts.hsf_status.berasesz == 0x1) {
+ sector_size = seg_size = ICH8_FLASH_SEG_SIZE_4K;
+ iteration = 1;
+ } else if (hsfsts.hsf_status.berasesz == 0x3) {
+ sector_size = seg_size = ICH8_FLASH_SEG_SIZE_64K;
+ iteration = 1;
+ } else {
+ return error;
+ }
+
+ for (j = 0; j < iteration ; j++) {
+ do {
+ count++;
+ /* Steps */
+ error = e1000_ich8_cycle_init(hw);
+ if (error != E1000_SUCCESS) {
+ error_flag = 1;
+ break;
+ }
+
+ /* Write a value 11 (block Erase) in Flash Cycle field in Hw flash
+ * Control */
+ hsflctl.regval = E1000_READ_ICH8_REG16(hw, ICH8_FLASH_HSFCTL);
+ hsflctl.hsf_ctrl.flcycle = ICH8_CYCLE_ERASE;
+ E1000_WRITE_ICH8_REG16(hw, ICH8_FLASH_HSFCTL, hsflctl.regval);
+
+ /* Write the last 24 bits of an index within the block into Flash
+ * Linear address field in Flash Address. This probably needs to
+ * be calculated here based off the on-chip segment size and the
+ * software segment size assumed (4K) */
+ /* TBD */
+ flash_linear_address = segment * sector_size + j * seg_size;
+ flash_linear_address &= ICH8_FLASH_LINEAR_ADDR_MASK;
+ flash_linear_address += hw->flash_base_addr;
+
+ E1000_WRITE_ICH8_REG(hw, ICH8_FLASH_FADDR, flash_linear_address);
+
+ error = e1000_ich8_flash_cycle(hw, 1000000);
+ /* Check if FCERR is set to 1. If 1, clear it and try the whole
+ * sequence a few more times else Done */
+ if (error == E1000_SUCCESS) {
+ break;
+ } else {
+ hsfsts.regval = E1000_READ_ICH8_REG16(hw, ICH8_FLASH_HSFSTS);
+ if (hsfsts.hsf_status.flcerr == 1) {
+ /* repeat for some time before giving up */
+ continue;
+ } else if (hsfsts.hsf_status.flcdone == 0) {
+ error_flag = 1;
+ break;
+ }
+ }
+ } while ((count < ICH8_FLASH_CYCLE_REPEAT_COUNT) && !error_flag);
+ if (error_flag == 1)
+ break;
+ }
+ if (error_flag != 1)
+ error = E1000_SUCCESS;
+ return error;
+}
+
+/******************************************************************************
+ *
+ * Reverse duplex setting without breaking the link.
+ *
+ * hw: Struct containing variables accessed by shared code
+ *
+ *****************************************************************************/
+int32_t
+e1000_duplex_reversal(struct e1000_hw *hw)
+{
+ int32_t ret_val;
+ uint16_t phy_data;
+
+ if (hw->phy_type != e1000_phy_igp_3)
+ return E1000_SUCCESS;
+
+ ret_val = e1000_read_phy_reg(hw, PHY_CTRL, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ phy_data ^= MII_CR_FULL_DUPLEX;
+
+ ret_val = e1000_write_phy_reg(hw, PHY_CTRL, phy_data);
+ if (ret_val)
+ return ret_val;
+
+ ret_val = e1000_read_phy_reg(hw, IGP3E1000_PHY_MISC_CTRL, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ phy_data |= IGP3_PHY_MISC_DUPLEX_MANUAL_SET;
+ ret_val = e1000_write_phy_reg(hw, IGP3E1000_PHY_MISC_CTRL, phy_data);
+
+ return ret_val;
+}
+
+int32_t
+e1000_init_lcd_from_nvm_config_region(struct e1000_hw *hw,
+ uint32_t cnf_base_addr, uint32_t cnf_size)
+{
+ uint32_t ret_val = E1000_SUCCESS;
+ uint16_t word_addr, reg_data, reg_addr;
+ uint16_t i;
+
+ /* cnf_base_addr is in DWORD */
+ word_addr = (uint16_t)(cnf_base_addr << 1);
+
+ /* cnf_size is returned in size of dwords */
+ for (i = 0; i < cnf_size; i++) {
+ ret_val = e1000_read_eeprom(hw, (word_addr + i*2), 1, ®_data);
+ if (ret_val)
+ return ret_val;
+
+ ret_val = e1000_read_eeprom(hw, (word_addr + i*2 + 1), 1, ®_addr);
+ if (ret_val)
+ return ret_val;
+
+ ret_val = e1000_get_software_flag(hw);
+ if (ret_val != E1000_SUCCESS)
+ return ret_val;
+
+ ret_val = e1000_write_phy_reg_ex(hw, (uint32_t)reg_addr, reg_data);
+
+ e1000_release_software_flag(hw);
+ }
+
+ return ret_val;
+}
+
+
+int32_t
+e1000_init_lcd_from_nvm(struct e1000_hw *hw)
+{
+ uint32_t reg_data, cnf_base_addr, cnf_size, ret_val, loop;
+
+ if (hw->phy_type != e1000_phy_igp_3)
+ return E1000_SUCCESS;
+
+ /* Check if SW needs configure the PHY */
+ reg_data = E1000_READ_REG(hw, FEXTNVM);
+ if (!(reg_data & FEXTNVM_SW_CONFIG))
+ return E1000_SUCCESS;
+
+ /* Wait for basic configuration completes before proceeding*/
+ loop = 0;
+ do {
+ reg_data = E1000_READ_REG(hw, STATUS) & E1000_STATUS_LAN_INIT_DONE;
+ udelay(100);
+ loop++;
+ } while ((!reg_data) && (loop < 50));
+
+ /* Clear the Init Done bit for the next init event */
+ reg_data = E1000_READ_REG(hw, STATUS);
+ reg_data &= ~E1000_STATUS_LAN_INIT_DONE;
+ E1000_WRITE_REG(hw, STATUS, reg_data);
+
+ /* Make sure HW does not configure LCD from PHY extended configuration
+ before SW configuration */
+ reg_data = E1000_READ_REG(hw, EXTCNF_CTRL);
+ if ((reg_data & E1000_EXTCNF_CTRL_LCD_WRITE_ENABLE) == 0x0000) {
+ reg_data = E1000_READ_REG(hw, EXTCNF_SIZE);
+ cnf_size = reg_data & E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH;
+ cnf_size >>= 16;
+ if (cnf_size) {
+ reg_data = E1000_READ_REG(hw, EXTCNF_CTRL);
+ cnf_base_addr = reg_data & E1000_EXTCNF_CTRL_EXT_CNF_POINTER;
+ /* cnf_base_addr is in DWORD */
+ cnf_base_addr >>= 16;
+
+ /* Configure LCD from extended configuration region. */
+ ret_val = e1000_init_lcd_from_nvm_config_region(hw, cnf_base_addr,
+ cnf_size);
+ if (ret_val)
+ return ret_val;
+ }
+ }
+
+ return E1000_SUCCESS;
+}
+
+
diff --git a/drivers/net/e1000/e1000_hw.h b/drivers/net/e1000/e1000_hw.h
index bfbc7d8..8961e07 100644
--- a/drivers/net/e1000/e1000_hw.h
+++ b/drivers/net/e1000/e1000_hw.h
@@ -62,6 +62,7 @@ typedef enum {
e1000_82572,
e1000_82573,
e1000_80003es2lan,
+ e1000_ich8lan,
e1000_num_macs
} e1000_mac_type;
@@ -70,6 +71,7 @@ typedef enum {
e1000_eeprom_spi,
e1000_eeprom_microwire,
e1000_eeprom_flash,
+ e1000_eeprom_ich8,
e1000_eeprom_none, /* No NVM support */
e1000_num_eeprom_types
} e1000_eeprom_type;
@@ -98,6 +100,11 @@ typedef enum {
e1000_fc_default = 0xFF
} e1000_fc_type;
+struct e1000_shadow_ram {
+ uint16_t eeprom_word;
+ boolean_t modified;
+};
+
/* PCI bus types */
typedef enum {
e1000_bus_type_unknown = 0,
@@ -218,6 +225,8 @@ typedef enum {
e1000_phy_igp,
e1000_phy_igp_2,
e1000_phy_gg82563,
+ e1000_phy_igp_3,
+ e1000_phy_ife,
e1000_phy_undefined = 0xFF
} e1000_phy_type;
@@ -313,6 +322,10 @@ int32_t e1000_read_phy_reg(struct e1000_
int32_t e1000_write_phy_reg(struct e1000_hw *hw, uint32_t reg_addr, uint16_t data);
int32_t e1000_phy_hw_reset(struct e1000_hw *hw);
int32_t e1000_phy_reset(struct e1000_hw *hw);
+void e1000_phy_powerdown_workaround(struct e1000_hw *hw);
+int32_t e1000_kumeran_lock_loss_workaround(struct e1000_hw *hw);
+int32_t e1000_init_lcd_from_nvm_config_region(struct e1000_hw *hw, uint32_t cnf_base_addr, uint32_t cnf_size);
+int32_t e1000_init_lcd_from_nvm(struct e1000_hw *hw);
int32_t e1000_phy_get_info(struct e1000_hw *hw, struct e1000_phy_info *phy_info);
int32_t e1000_validate_mdi_setting(struct e1000_hw *hw);
int32_t e1000_read_kmrn_reg(struct e1000_hw *hw, uint32_t reg_addr, uint16_t *data);
@@ -331,6 +344,7 @@ uint32_t e1000_enable_mng_pass_thru(stru
#define E1000_MNG_DHCP_COOKIE_OFFSET 0x6F0 /* Cookie offset */
#define E1000_MNG_DHCP_COOKIE_LENGTH 0x10 /* Cookie length */
#define E1000_MNG_IAMT_MODE 0x3
+#define E1000_MNG_ICH_IAMT_MODE 0x2
#define E1000_IAMT_SIGNATURE 0x544D4149 /* Intel(R) Active Management Technology signature */
#define E1000_MNG_DHCP_COOKIE_STATUS_PARSING_SUPPORT 0x1 /* DHCP parsing enabled */
@@ -388,6 +402,8 @@ int32_t e1000_read_part_num(struct e1000
int32_t e1000_read_mac_addr(struct e1000_hw * hw);
int32_t e1000_swfw_sync_acquire(struct e1000_hw *hw, uint16_t mask);
void e1000_swfw_sync_release(struct e1000_hw *hw, uint16_t mask);
+void e1000_release_software_flag(struct e1000_hw *hw);
+int32_t e1000_get_software_flag(struct e1000_hw *hw);
/* Filters (multicast, vlan, receive) */
void e1000_mc_addr_list_update(struct e1000_hw *hw, uint8_t * mc_addr_list, uint32_t mc_addr_count, uint32_t pad, uint32_t rar_used_count);
@@ -423,6 +439,29 @@ int32_t e1000_disable_pciex_master(struc
int32_t e1000_get_software_semaphore(struct e1000_hw *hw);
void e1000_release_software_semaphore(struct e1000_hw *hw);
int32_t e1000_check_phy_reset_block(struct e1000_hw *hw);
+int32_t e1000_set_pci_ex_no_snoop(struct e1000_hw *hw, uint32_t no_snoop);
+
+int32_t e1000_read_ich8_byte(struct e1000_hw *hw, uint32_t index,
+ uint8_t *data);
+int32_t e1000_verify_write_ich8_byte(struct e1000_hw *hw, uint32_t index,
+ uint8_t byte);
+int32_t e1000_write_ich8_byte(struct e1000_hw *hw, uint32_t index,
+ uint8_t byte);
+int32_t e1000_read_ich8_word(struct e1000_hw *hw, uint32_t index,
+ uint16_t *data);
+int32_t e1000_read_ich8_data(struct e1000_hw *hw, uint32_t index,
+ uint32_t size, uint16_t *data);
+int32_t e1000_read_eeprom_ich8(struct e1000_hw *hw, uint16_t offset,
+ uint16_t words, uint16_t *data);
+int32_t e1000_write_eeprom_ich8(struct e1000_hw *hw, uint16_t offset,
+ uint16_t words, uint16_t *data);
+int32_t e1000_erase_ich8_4k_segment(struct e1000_hw *hw, uint32_t segment);
+
+
+#define E1000_READ_REG_IO(a, reg) \
+ e1000_read_reg_io((a), E1000_##reg)
+#define E1000_WRITE_REG_IO(a, reg, val) \
+ e1000_write_reg_io((a), E1000_##reg, val)
/* PCI Device IDs */
#define E1000_DEV_ID_82542 0x1000
@@ -447,6 +486,7 @@ int32_t e1000_check_phy_reset_block(stru
#define E1000_DEV_ID_82546EB_QUAD_COPPER 0x101D
#define E1000_DEV_ID_82541EI 0x1013
#define E1000_DEV_ID_82541EI_MOBILE 0x1018
+#define E1000_DEV_ID_82541ER_LOM 0x1014
#define E1000_DEV_ID_82541ER 0x1078
#define E1000_DEV_ID_82547GI 0x1075
#define E1000_DEV_ID_82541GI 0x1076
@@ -458,18 +498,28 @@ int32_t e1000_check_phy_reset_block(stru
#define E1000_DEV_ID_82546GB_PCIE 0x108A
#define E1000_DEV_ID_82546GB_QUAD_COPPER 0x1099
#define E1000_DEV_ID_82547EI 0x1019
+#define E1000_DEV_ID_82547EI_MOBILE 0x101A
#define E1000_DEV_ID_82571EB_COPPER 0x105E
#define E1000_DEV_ID_82571EB_FIBER 0x105F
#define E1000_DEV_ID_82571EB_SERDES 0x1060
#define E1000_DEV_ID_82572EI_COPPER 0x107D
#define E1000_DEV_ID_82572EI_FIBER 0x107E
#define E1000_DEV_ID_82572EI_SERDES 0x107F
+#define E1000_DEV_ID_82572EI 0x10B9
#define E1000_DEV_ID_82573E 0x108B
#define E1000_DEV_ID_82573E_IAMT 0x108C
#define E1000_DEV_ID_82573L 0x109A
#define E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3 0x10B5
#define E1000_DEV_ID_80003ES2LAN_COPPER_DPT 0x1096
#define E1000_DEV_ID_80003ES2LAN_SERDES_DPT 0x1098
+#define E1000_DEV_ID_80003ES2LAN_COPPER_SPT 0x10BA
+#define E1000_DEV_ID_80003ES2LAN_SERDES_SPT 0x10BB
+
+#define E1000_DEV_ID_ICH8_IGP_M_AMT 0x1049
+#define E1000_DEV_ID_ICH8_IGP_AMT 0x104A
+#define E1000_DEV_ID_ICH8_IGP_C 0x104B
+#define E1000_DEV_ID_ICH8_IFE 0x104C
+#define E1000_DEV_ID_ICH8_IGP_M 0x104D
#define NODE_ADDRESS_SIZE 6
@@ -540,6 +590,14 @@ int32_t e1000_check_phy_reset_block(stru
E1000_IMS_RXSEQ | \
E1000_IMS_LSC)
+/* Additional interrupts need to be handled for e1000_ich8lan:
+ DSW = The FW changed the status of the DISSW bit in FWSM
+ PHYINT = The LAN connected device generates an interrupt
+ EPRST = Manageability reset event */
+#define IMS_ICH8LAN_ENABLE_MASK (\
+ E1000_IMS_DSW | \
+ E1000_IMS_PHYINT | \
+ E1000_IMS_EPRST)
/* Number of high/low register pairs in the RAR. The RAR (Receive Address
* Registers) holds the directed and multicast addresses that we monitor. We
@@ -547,6 +605,7 @@ int32_t e1000_check_phy_reset_block(stru
* E1000_RAR_ENTRIES - 1 multicast addresses.
*/
#define E1000_RAR_ENTRIES 15
+#define E1000_RAR_ENTRIES_ICH8LAN 7
#define MIN_NUMBER_OF_DESCRIPTORS 8
#define MAX_NUMBER_OF_DESCRIPTORS 0xFFF8
@@ -768,6 +827,9 @@ struct e1000_data_desc {
#define E1000_MC_TBL_SIZE 128 /* Multicast Filter Table (4096 bits) */
#define E1000_VLAN_FILTER_TBL_SIZE 128 /* VLAN Filter Table (4096 bits) */
+#define E1000_NUM_UNICAST_ICH8LAN 7
+#define E1000_MC_TBL_SIZE_ICH8LAN 32
+
/* Receive Address Register */
struct e1000_rar {
@@ -777,6 +839,7 @@ struct e1000_rar {
/* Number of entries in the Multicast Table Array (MTA). */
#define E1000_NUM_MTA_REGISTERS 128
+#define E1000_NUM_MTA_REGISTERS_ICH8LAN 32
/* IPv4 Address Table Entry */
struct e1000_ipv4_at_entry {
@@ -787,6 +850,7 @@ struct e1000_ipv4_at_entry {
/* Four wakeup IP addresses are supported */
#define E1000_WAKEUP_IP_ADDRESS_COUNT_MAX 4
#define E1000_IP4AT_SIZE E1000_WAKEUP_IP_ADDRESS_COUNT_MAX
+#define E1000_IP4AT_SIZE_ICH8LAN 3
#define E1000_IP6AT_SIZE 1
/* IPv6 Address Table Entry */
@@ -845,6 +909,7 @@ struct e1000_ffvt_entry {
#define E1000_FLA 0x0001C /* Flash Access - RW */
#define E1000_MDIC 0x00020 /* MDI Control - RW */
#define E1000_SCTL 0x00024 /* SerDes Control - RW */
+#define E1000_FEXTNVM 0x00028 /* Future Extended NVM register */
#define E1000_FCAL 0x00028 /* Flow Control Address Low - RW */
#define E1000_FCAH 0x0002C /* Flow Control Address High -RW */
#define E1000_FCT 0x00030 /* Flow Control Type - RW */
@@ -873,6 +938,8 @@ struct e1000_ffvt_entry {
#define E1000_LEDCTL 0x00E00 /* LED Control - RW */
#define E1000_EXTCNF_CTRL 0x00F00 /* Extended Configuration Control */
#define E1000_EXTCNF_SIZE 0x00F08 /* Extended Configuration Size */
+#define E1000_PHY_CTRL 0x00F10 /* PHY Control Register in CSR */
+#define FEXTNVM_SW_CONFIG 0x0001
#define E1000_PBA 0x01000 /* Packet Buffer Allocation - RW */
#define E1000_PBS 0x01008 /* Packet Buffer Size */
#define E1000_EEMNGCTL 0x01010 /* MNG EEprom Control */
@@ -900,11 +967,13 @@ struct e1000_ffvt_entry {
#define E1000_RDH0 E1000_RDH /* RX Desc Head (0) - RW */
#define E1000_RDT0 E1000_RDT /* RX Desc Tail (0) - RW */
#define E1000_RDTR0 E1000_RDTR /* RX Delay Timer (0) - RW */
-#define E1000_RXDCTL 0x02828 /* RX Descriptor Control - RW */
+#define E1000_RXDCTL 0x02828 /* RX Descriptor Control queue 0 - RW */
+#define E1000_RXDCTL1 0x02928 /* RX Descriptor Control queue 1 - RW */
#define E1000_RADV 0x0282C /* RX Interrupt Absolute Delay Timer - RW */
#define E1000_RSRPD 0x02C00 /* RX Small Packet Detect - RW */
#define E1000_RAID 0x02C08 /* Receive Ack Interrupt Delay - RW */
#define E1000_TXDMAC 0x03000 /* TX DMA Control - RW */
+#define E1000_KABGTXD 0x03004 /* AFE Band Gap Transmit Ref Data */
#define E1000_TDFH 0x03410 /* TX Data FIFO Head - RW */
#define E1000_TDFT 0x03418 /* TX Data FIFO Tail - RW */
#define E1000_TDFHS 0x03420 /* TX Data FIFO Head Saved - RW */
@@ -1051,6 +1120,7 @@ struct e1000_ffvt_entry {
#define E1000_82542_FLA E1000_FLA
#define E1000_82542_MDIC E1000_MDIC
#define E1000_82542_SCTL E1000_SCTL
+#define E1000_82542_FEXTNVM E1000_FEXTNVM
#define E1000_82542_FCAL E1000_FCAL
#define E1000_82542_FCAH E1000_FCAH
#define E1000_82542_FCT E1000_FCT
@@ -1074,6 +1144,19 @@ struct e1000_ffvt_entry {
#define E1000_82542_RDLEN0 E1000_82542_RDLEN
#define E1000_82542_RDH0 E1000_82542_RDH
#define E1000_82542_RDT0 E1000_82542_RDT
+#define E1000_82542_SRRCTL(_n) (0x280C + ((_n) << 8)) /* Split and Replication
+ * RX Control - RW */
+#define E1000_82542_DCA_RXCTRL(_n) (0x02814 + ((_n) << 8))
+#define E1000_82542_RDBAH3 0x02B04 /* RX Desc Base High Queue 3 - RW */
+#define E1000_82542_RDBAL3 0x02B00 /* RX Desc Low Queue 3 - RW */
+#define E1000_82542_RDLEN3 0x02B08 /* RX Desc Length Queue 3 - RW */
+#define E1000_82542_RDH3 0x02B10 /* RX Desc Head Queue 3 - RW */
+#define E1000_82542_RDT3 0x02B18 /* RX Desc Tail Queue 3 - RW */
+#define E1000_82542_RDBAL2 0x02A00 /* RX Desc Base Low Queue 2 - RW */
+#define E1000_82542_RDBAH2 0x02A04 /* RX Desc Base High Queue 2 - RW */
+#define E1000_82542_RDLEN2 0x02A08 /* RX Desc Length Queue 2 - RW */
+#define E1000_82542_RDH2 0x02A10 /* RX Desc Head Queue 2 - RW */
+#define E1000_82542_RDT2 0x02A18 /* RX Desc Tail Queue 2 - RW */
#define E1000_82542_RDTR1 0x00130
#define E1000_82542_RDBAL1 0x00138
#define E1000_82542_RDBAH1 0x0013C
@@ -1111,11 +1194,14 @@ struct e1000_ffvt_entry {
#define E1000_82542_FLOP E1000_FLOP
#define E1000_82542_EXTCNF_CTRL E1000_EXTCNF_CTRL
#define E1000_82542_EXTCNF_SIZE E1000_EXTCNF_SIZE
+#define E1000_82542_PHY_CTRL E1000_PHY_CTRL
#define E1000_82542_ERT E1000_ERT
#define E1000_82542_RXDCTL E1000_RXDCTL
+#define E1000_82542_RXDCTL1 E1000_RXDCTL1
#define E1000_82542_RADV E1000_RADV
#define E1000_82542_RSRPD E1000_RSRPD
#define E1000_82542_TXDMAC E1000_TXDMAC
+#define E1000_82542_KABGTXD E1000_KABGTXD
#define E1000_82542_TDFHS E1000_TDFHS
#define E1000_82542_TDFTS E1000_TDFTS
#define E1000_82542_TDFPC E1000_TDFPC
@@ -1311,13 +1397,16 @@ struct e1000_hw_stats {
/* Structure containing variables used by the shared code (e1000_hw.c) */
struct e1000_hw {
- uint8_t __iomem *hw_addr;
+ uint8_t *hw_addr;
uint8_t *flash_address;
e1000_mac_type mac_type;
e1000_phy_type phy_type;
uint32_t phy_init_script;
e1000_media_type media_type;
void *back;
+ struct e1000_shadow_ram *eeprom_shadow_ram;
+ uint32_t flash_bank_size;
+ uint32_t flash_base_addr;
e1000_fc_type fc;
e1000_bus_speed bus_speed;
e1000_bus_width bus_width;
@@ -1329,6 +1418,7 @@ struct e1000_hw {
uint32_t asf_firmware_present;
uint32_t eeprom_semaphore_present;
uint32_t swfw_sync_present;
+ uint32_t swfwhw_semaphore_present;
unsigned long io_base;
uint32_t phy_id;
uint32_t phy_revision;
@@ -1388,6 +1478,7 @@ struct e1000_hw {
boolean_t in_ifs_mode;
boolean_t mng_reg_access_disabled;
boolean_t leave_av_bit_off;
+ boolean_t kmrn_lock_loss_workaround_disabled;
};
@@ -1436,6 +1527,7 @@ struct e1000_hw {
#define E1000_CTRL_RTE 0x20000000 /* Routing tag enable */
#define E1000_CTRL_VME 0x40000000 /* IEEE VLAN mode enable */
#define E1000_CTRL_PHY_RST 0x80000000 /* PHY Reset */
+#define E1000_CTRL_SW2FW_INT 0x02000000 /* Initiate an interrupt to manageability engine */
/* Device Status */
#define E1000_STATUS_FD 0x00000001 /* Full duplex.0=half,1=full */
@@ -1450,6 +1542,8 @@ struct e1000_hw {
#define E1000_STATUS_SPEED_10 0x00000000 /* Speed 10Mb/s */
#define E1000_STATUS_SPEED_100 0x00000040 /* Speed 100Mb/s */
#define E1000_STATUS_SPEED_1000 0x00000080 /* Speed 1000Mb/s */
+#define E1000_STATUS_LAN_INIT_DONE 0x00000200 /* Lan Init Completion
+ by EEPROM/Flash */
#define E1000_STATUS_ASDV 0x00000300 /* Auto speed detect value */
#define E1000_STATUS_DOCK_CI 0x00000800 /* Change in Dock/Undock state. Clear on write '0'. */
#define E1000_STATUS_GIO_MASTER_ENABLE 0x00080000 /* Status of Master requests. */
@@ -1507,6 +1601,10 @@ struct e1000_hw {
#define E1000_STM_OPCODE 0xDB00
#define E1000_HICR_FW_RESET 0xC0
+#define E1000_SHADOW_RAM_WORDS 2048
+#define E1000_ICH8_NVM_SIG_WORD 0x13
+#define E1000_ICH8_NVM_SIG_MASK 0xC0
+
/* EEPROM Read */
#define E1000_EERD_START 0x00000001 /* Start Read */
#define E1000_EERD_DONE 0x00000010 /* Read Done */
@@ -1552,7 +1650,6 @@ struct e1000_hw {
#define E1000_CTRL_EXT_WR_WMARK_320 0x01000000
#define E1000_CTRL_EXT_WR_WMARK_384 0x02000000
#define E1000_CTRL_EXT_WR_WMARK_448 0x03000000
-#define E1000_CTRL_EXT_CANC 0x04000000 /* Interrupt delay cancellation */
#define E1000_CTRL_EXT_DRV_LOAD 0x10000000 /* Driver loaded bit for FW */
#define E1000_CTRL_EXT_IAME 0x08000000 /* Interrupt acknowledge Auto-mask */
#define E1000_CTRL_EXT_INT_TIMER_CLR 0x20000000 /* Clear Interrupt timers after IMS clear */
@@ -1592,12 +1689,31 @@ struct e1000_hw {
#define E1000_KUMCTRLSTA_FIFO_CTRL_TX_BYPASS 0x00000800
/* In-Band Control */
+#define E1000_KUMCTRLSTA_INB_CTRL_LINK_STATUS_TX_TIMEOUT_DEFAULT 0x00000500
#define E1000_KUMCTRLSTA_INB_CTRL_DIS_PADDING 0x00000010
/* Half-Duplex Control */
#define E1000_KUMCTRLSTA_HD_CTRL_10_100_DEFAULT 0x00000004
#define E1000_KUMCTRLSTA_HD_CTRL_1000_DEFAULT 0x00000000
+#define E1000_KUMCTRLSTA_OFFSET_K0S_CTRL 0x0000001E
+
+#define E1000_KUMCTRLSTA_DIAG_FELPBK 0x2000
+#define E1000_KUMCTRLSTA_DIAG_NELPBK 0x1000
+
+#define E1000_KUMCTRLSTA_K0S_100_EN 0x2000
+#define E1000_KUMCTRLSTA_K0S_GBE_EN 0x1000
+#define E1000_KUMCTRLSTA_K0S_ENTRY_LATENCY_MASK 0x0003
+
+#define E1000_KABGTXD_BGSQLBIAS 0x00050000
+
+#define E1000_PHY_CTRL_SPD_EN 0x00000001
+#define E1000_PHY_CTRL_D0A_LPLU 0x00000002
+#define E1000_PHY_CTRL_NOND0A_LPLU 0x00000004
+#define E1000_PHY_CTRL_NOND0A_GBE_DISABLE 0x00000008
+#define E1000_PHY_CTRL_GBE_DISABLE 0x00000040
+#define E1000_PHY_CTRL_B2B_EN 0x00000080
+
/* LED Control */
#define E1000_LEDCTL_LED0_MODE_MASK 0x0000000F
#define E1000_LEDCTL_LED0_MODE_SHIFT 0
@@ -1667,6 +1783,9 @@ struct e1000_hw {
#define E1000_ICR_RXD_FIFO_PAR1 0x01000000 /* queue 1 Rx descriptor FIFO parity error */
#define E1000_ICR_TXD_FIFO_PAR1 0x02000000 /* queue 1 Tx descriptor FIFO parity error */
#define E1000_ICR_ALL_PARITY 0x03F00000 /* all parity error bits */
+#define E1000_ICR_DSW 0x00000020 /* FW changed the status of DISSW bit in the FWSM */
+#define E1000_ICR_PHYINT 0x00001000 /* LAN connected device generates an interrupt */
+#define E1000_ICR_EPRST 0x00100000 /* ME handware reset occurs */
/* Interrupt Cause Set */
#define E1000_ICS_TXDW E1000_ICR_TXDW /* Transmit desc written back */
@@ -1693,6 +1812,9 @@ struct e1000_hw {
#define E1000_ICS_PB_PAR E1000_ICR_PB_PAR /* packet buffer parity error */
#define E1000_ICS_RXD_FIFO_PAR1 E1000_ICR_RXD_FIFO_PAR1 /* queue 1 Rx descriptor FIFO parity error */
#define E1000_ICS_TXD_FIFO_PAR1 E1000_ICR_TXD_FIFO_PAR1 /* queue 1 Tx descriptor FIFO parity error */
+#define E1000_ICS_DSW E1000_ICR_DSW
+#define E1000_ICS_PHYINT E1000_ICR_PHYINT
+#define E1000_ICS_EPRST E1000_ICR_EPRST
/* Interrupt Mask Set */
#define E1000_IMS_TXDW E1000_ICR_TXDW /* Transmit desc written back */
@@ -1719,6 +1841,9 @@ struct e1000_hw {
#define E1000_IMS_PB_PAR E1000_ICR_PB_PAR /* packet buffer parity error */
#define E1000_IMS_RXD_FIFO_PAR1 E1000_ICR_RXD_FIFO_PAR1 /* queue 1 Rx descriptor FIFO parity error */
#define E1000_IMS_TXD_FIFO_PAR1 E1000_ICR_TXD_FIFO_PAR1 /* queue 1 Tx descriptor FIFO parity error */
+#define E1000_IMS_DSW E1000_ICR_DSW
+#define E1000_IMS_PHYINT E1000_ICR_PHYINT
+#define E1000_IMS_EPRST E1000_ICR_EPRST
/* Interrupt Mask Clear */
#define E1000_IMC_TXDW E1000_ICR_TXDW /* Transmit desc written back */
@@ -1745,6 +1870,9 @@ struct e1000_hw {
#define E1000_IMC_PB_PAR E1000_ICR_PB_PAR /* packet buffer parity error */
#define E1000_IMC_RXD_FIFO_PAR1 E1000_ICR_RXD_FIFO_PAR1 /* queue 1 Rx descriptor FIFO parity error */
#define E1000_IMC_TXD_FIFO_PAR1 E1000_ICR_TXD_FIFO_PAR1 /* queue 1 Tx descriptor FIFO parity error */
+#define E1000_IMC_DSW E1000_ICR_DSW
+#define E1000_IMC_PHYINT E1000_ICR_PHYINT
+#define E1000_IMC_EPRST E1000_ICR_EPRST
/* Receive Control */
#define E1000_RCTL_RST 0x00000001 /* Software reset */
@@ -1919,9 +2047,10 @@ struct e1000_hw {
#define E1000_MRQC_RSS_FIELD_MASK 0xFFFF0000
#define E1000_MRQC_RSS_FIELD_IPV4_TCP 0x00010000
#define E1000_MRQC_RSS_FIELD_IPV4 0x00020000
-#define E1000_MRQC_RSS_FIELD_IPV6_TCP 0x00040000
+#define E1000_MRQC_RSS_FIELD_IPV6_TCP_EX 0x00040000
#define E1000_MRQC_RSS_FIELD_IPV6_EX 0x00080000
#define E1000_MRQC_RSS_FIELD_IPV6 0x00100000
+#define E1000_MRQC_RSS_FIELD_IPV6_TCP 0x00200000
/* Definitions for power management and wakeup registers */
/* Wake Up Control */
@@ -2011,6 +2140,15 @@ struct e1000_hw {
#define E1000_FWSM_MODE_SHIFT 1
#define E1000_FWSM_FW_VALID 0x00008000 /* FW established a valid mode */
+#define E1000_FWSM_RSPCIPHY 0x00000040 /* Reset PHY on PCI reset */
+#define E1000_FWSM_DISSW 0x10000000 /* FW disable SW Write Access */
+#define E1000_FWSM_SKUSEL_MASK 0x60000000 /* LAN SKU select */
+#define E1000_FWSM_SKUEL_SHIFT 29
+#define E1000_FWSM_SKUSEL_EMB 0x0 /* Embedded SKU */
+#define E1000_FWSM_SKUSEL_CONS 0x1 /* Consumer SKU */
+#define E1000_FWSM_SKUSEL_PERF_100 0x2 /* Perf & Corp 10/100 SKU */
+#define E1000_FWSM_SKUSEL_PERF_GBE 0x3 /* Perf & Copr GbE SKU */
+
/* FFLT Debug Register */
#define E1000_FFLT_DBG_INVC 0x00100000 /* Invalid /C/ code handling */
@@ -2083,6 +2221,8 @@ struct e1000_host_command_info {
E1000_GCR_TXDSCW_NO_SNOOP | \
E1000_GCR_TXDSCR_NO_SNOOP)
+#define PCI_EX_82566_SNOOP_ALL PCI_EX_NO_SNOOP_ALL
+
#define E1000_GCR_L1_ACT_WITHOUT_L0S_RX 0x08000000
/* Function Active and Power State to MNG */
#define E1000_FACTPS_FUNC0_POWER_STATE_MASK 0x00000003
@@ -2141,8 +2281,10 @@ struct e1000_host_command_info {
#define EEPROM_PHY_CLASS_WORD 0x0007
#define EEPROM_INIT_CONTROL1_REG 0x000A
#define EEPROM_INIT_CONTROL2_REG 0x000F
+#define EEPROM_SWDEF_PINS_CTRL_PORT_1 0x0010
#define EEPROM_INIT_CONTROL3_PORT_B 0x0014
#define EEPROM_INIT_3GIO_3 0x001A
+#define EEPROM_SWDEF_PINS_CTRL_PORT_0 0x0020
#define EEPROM_INIT_CONTROL3_PORT_A 0x0024
#define EEPROM_CFG 0x0012
#define EEPROM_FLASH_VERSION 0x0032
@@ -2154,10 +2296,16 @@ struct e1000_host_command_info {
/* Word definitions for ID LED Settings */
#define ID_LED_RESERVED_0000 0x0000
#define ID_LED_RESERVED_FFFF 0xFFFF
+#define ID_LED_RESERVED_82573 0xF746
+#define ID_LED_DEFAULT_82573 0x1811
#define ID_LED_DEFAULT ((ID_LED_OFF1_ON2 << 12) | \
(ID_LED_OFF1_OFF2 << 8) | \
(ID_LED_DEF1_DEF2 << 4) | \
(ID_LED_DEF1_DEF2))
+#define ID_LED_DEFAULT_ICH8LAN ((ID_LED_DEF1_DEF2 << 12) | \
+ (ID_LED_DEF1_OFF2 << 8) | \
+ (ID_LED_DEF1_ON2 << 4) | \
+ (ID_LED_DEF1_DEF2))
#define ID_LED_DEF1_DEF2 0x1
#define ID_LED_DEF1_ON2 0x2
#define ID_LED_DEF1_OFF2 0x3
@@ -2192,6 +2340,11 @@ struct e1000_host_command_info {
#define EEPROM_WORD0F_ASM_DIR 0x2000
#define EEPROM_WORD0F_ANE 0x0800
#define EEPROM_WORD0F_SWPDIO_EXT 0x00F0
+#define EEPROM_WORD0F_LPLU 0x0001
+
+/* Mask bits for fields in Word 0x10/0x20 of the EEPROM */
+#define EEPROM_WORD1020_GIGA_DISABLE 0x0010
+#define EEPROM_WORD1020_GIGA_DISABLE_NON_D0A 0x0008
/* Mask bits for fields in Word 0x1a of the EEPROM */
#define EEPROM_WORD1A_ASPM_MASK 0x000C
@@ -2266,23 +2419,29 @@ struct e1000_host_command_info {
#define E1000_EXTCNF_CTRL_D_UD_OWNER 0x00000010
#define E1000_EXTCNF_CTRL_MDIO_SW_OWNERSHIP 0x00000020
#define E1000_EXTCNF_CTRL_MDIO_HW_OWNERSHIP 0x00000040
-#define E1000_EXTCNF_CTRL_EXT_CNF_POINTER 0x1FFF0000
+#define E1000_EXTCNF_CTRL_EXT_CNF_POINTER 0x0FFF0000
#define E1000_EXTCNF_SIZE_EXT_PHY_LENGTH 0x000000FF
#define E1000_EXTCNF_SIZE_EXT_DOCK_LENGTH 0x0000FF00
#define E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH 0x00FF0000
+#define E1000_EXTCNF_CTRL_LCD_WRITE_ENABLE 0x00000001
+#define E1000_EXTCNF_CTRL_SWFLAG 0x00000020
/* PBA constants */
+#define E1000_PBA_8K 0x0008 /* 8KB, default Rx allocation */
#define E1000_PBA_12K 0x000C /* 12KB, default Rx allocation */
#define E1000_PBA_16K 0x0010 /* 16KB, default TX allocation */
#define E1000_PBA_22K 0x0016
#define E1000_PBA_24K 0x0018
#define E1000_PBA_30K 0x001E
#define E1000_PBA_32K 0x0020
+#define E1000_PBA_34K 0x0022
#define E1000_PBA_38K 0x0026
#define E1000_PBA_40K 0x0028
#define E1000_PBA_48K 0x0030 /* 48KB, default RX allocation */
+#define E1000_PBS_16K E1000_PBA_16K
+
/* Flow Control Constants */
#define FLOW_CONTROL_ADDRESS_LOW 0x00C28001
#define FLOW_CONTROL_ADDRESS_HIGH 0x00000100
@@ -2337,7 +2496,7 @@ struct e1000_host_command_info {
/* Number of milliseconds we wait for Eeprom auto read bit done after MAC reset */
#define AUTO_READ_DONE_TIMEOUT 10
/* Number of milliseconds we wait for PHY configuration done after MAC reset */
-#define PHY_CFG_TIMEOUT 40
+#define PHY_CFG_TIMEOUT 100
#define E1000_TX_BUFFER_SIZE ((uint32_t)1514)
@@ -3002,6 +3161,221 @@ struct e1000_host_command_info {
#define L1LXT971A_PHY_ID 0x001378E0
#define GG82563_E_PHY_ID 0x01410CA0
+
+/* Bits...
+ * 15-5: page
+ * 4-0: register offset
+ */
+#define PHY_PAGE_SHIFT 5
+#define PHY_REG(page, reg) \
+ (((page) << PHY_PAGE_SHIFT) | ((reg) & MAX_PHY_REG_ADDRESS))
+
+#define IGP3_PHY_PORT_CTRL \
+ PHY_REG(769, 17) /* Port General Configuration */
+#define IGP3_PHY_RATE_ADAPT_CTRL \
+ PHY_REG(769, 25) /* Rate Adapter Control Register */
+
+#define IGP3_KMRN_FIFO_CTRL_STATS \
+ PHY_REG(770, 16) /* KMRN FIFO's control/status register */
+#define IGP3_KMRN_POWER_MNG_CTRL \
+ PHY_REG(770, 17) /* KMRN Power Management Control Register */
+#define IGP3_KMRN_INBAND_CTRL \
+ PHY_REG(770, 18) /* KMRN Inband Control Register */
+#define IGP3_KMRN_DIAG \
+ PHY_REG(770, 19) /* KMRN Diagnostic register */
+#define IGP3_KMRN_DIAG_PCS_LOCK_LOSS 0x0002 /* RX PCS is not synced */
+#define IGP3_KMRN_ACK_TIMEOUT \
+ PHY_REG(770, 20) /* KMRN Acknowledge Timeouts register */
+
+#define IGP3_VR_CTRL \
+ PHY_REG(776, 18) /* Voltage regulator control register */
+#define IGP3_VR_CTRL_MODE_SHUT 0x0200 /* Enter powerdown, shutdown VRs */
+
+#define IGP3_CAPABILITY \
+ PHY_REG(776, 19) /* IGP3 Capability Register */
+
+/* Capabilities for SKU Control */
+#define IGP3_CAP_INITIATE_TEAM 0x0001 /* Able to initiate a team */
+#define IGP3_CAP_WFM 0x0002 /* Support WoL and PXE */
+#define IGP3_CAP_ASF 0x0004 /* Support ASF */
+#define IGP3_CAP_LPLU 0x0008 /* Support Low Power Link Up */
+#define IGP3_CAP_DC_AUTO_SPEED 0x0010 /* Support AC/DC Auto Link Speed */
+#define IGP3_CAP_SPD 0x0020 /* Support Smart Power Down */
+#define IGP3_CAP_MULT_QUEUE 0x0040 /* Support 2 tx & 2 rx queues */
+#define IGP3_CAP_RSS 0x0080 /* Support RSS */
+#define IGP3_CAP_8021PQ 0x0100 /* Support 802.1Q & 802.1p */
+#define IGP3_CAP_AMT_CB 0x0200 /* Support active manageability and circuit breaker */
+
+#define IGP3_PPC_JORDAN_EN 0x0001
+#define IGP3_PPC_JORDAN_GIGA_SPEED 0x0002
+
+#define IGP3_KMRN_PMC_EE_IDLE_LINK_DIS 0x0001
+#define IGP3_KMRN_PMC_K0S_ENTRY_LATENCY_MASK 0x001E
+#define IGP3_KMRN_PMC_K0S_MODE1_EN_GIGA 0x0020
+#define IGP3_KMRN_PMC_K0S_MODE1_EN_100 0x0040
+
+#define IGP3E1000_PHY_MISC_CTRL 0x1B /* Misc. Ctrl register */
+#define IGP3_PHY_MISC_DUPLEX_MANUAL_SET 0x1000 /* Duplex Manual Set */
+
+#define IGP3_KMRN_EXT_CTRL PHY_REG(770, 18)
+#define IGP3_KMRN_EC_DIS_INBAND 0x0080
+
+#define IGP03E1000_E_PHY_ID 0x02A80390
+#define IFE_E_PHY_ID 0x02A80330 /* 10/100 PHY */
+#define IFE_PLUS_E_PHY_ID 0x02A80320
+#define IFE_C_E_PHY_ID 0x02A80310
+
+#define IFE_PHY_EXTENDED_STATUS_CONTROL 0x10 /* 100BaseTx Extended Status, Control and Address */
+#define IFE_PHY_SPECIAL_CONTROL 0x11 /* 100BaseTx PHY special control register */
+#define IFE_PHY_RCV_FALSE_CARRIER 0x13 /* 100BaseTx Receive False Carrier Counter */
+#define IFE_PHY_RCV_DISCONNECT 0x14 /* 100BaseTx Receive Disconnet Counter */
+#define IFE_PHY_RCV_ERROT_FRAME 0x15 /* 100BaseTx Receive Error Frame Counter */
+#define IFE_PHY_RCV_SYMBOL_ERR 0x16 /* Receive Symbol Error Counter */
+#define IFE_PHY_PREM_EOF_ERR 0x17 /* 100BaseTx Receive Premature End Of Frame Error Counter */
+#define IFE_PHY_RCV_EOF_ERR 0x18 /* 10BaseT Receive End Of Frame Error Counter */
+#define IFE_PHY_TX_JABBER_DETECT 0x19 /* 10BaseT Transmit Jabber Detect Counter */
+#define IFE_PHY_EQUALIZER 0x1A /* PHY Equalizer Control and Status */
+#define IFE_PHY_SPECIAL_CONTROL_LED 0x1B /* PHY special control and LED configuration */
+#define IFE_PHY_MDIX_CONTROL 0x1C /* MDI/MDI-X Control register */
+#define IFE_PHY_HWI_CONTROL 0x1D /* Hardware Integrity Control (HWI) */
+
+#define IFE_PESC_REDUCED_POWER_DOWN_DISABLE 0x2000 /* Defaut 1 = Disable auto reduced power down */
+#define IFE_PESC_100BTX_POWER_DOWN 0x0400 /* Indicates the power state of 100BASE-TX */
+#define IFE_PESC_10BTX_POWER_DOWN 0x0200 /* Indicates the power state of 10BASE-T */
+#define IFE_PESC_POLARITY_REVERSED 0x0100 /* Indicates 10BASE-T polarity */
+#define IFE_PESC_PHY_ADDR_MASK 0x007C /* Bit 6:2 for sampled PHY address */
+#define IFE_PESC_SPEED 0x0002 /* Auto-negotiation speed result 1=100Mbs, 0=10Mbs */
+#define IFE_PESC_DUPLEX 0x0001 /* Auto-negotiation duplex result 1=Full, 0=Half */
+#define IFE_PESC_POLARITY_REVERSED_SHIFT 8
+
+#define IFE_PSC_DISABLE_DYNAMIC_POWER_DOWN 0x0100 /* 1 = Dyanmic Power Down disabled */
+#define IFE_PSC_FORCE_POLARITY 0x0020 /* 1=Reversed Polarity, 0=Normal */
+#define IFE_PSC_AUTO_POLARITY_DISABLE 0x0010 /* 1=Auto Polarity Disabled, 0=Enabled */
+#define IFE_PSC_JABBER_FUNC_DISABLE 0x0001 /* 1=Jabber Disabled, 0=Normal Jabber Operation */
+#define IFE_PSC_FORCE_POLARITY_SHIFT 5
+#define IFE_PSC_AUTO_POLARITY_DISABLE_SHIFT 4
+
+#define IFE_PMC_AUTO_MDIX 0x0080 /* 1=enable MDI/MDI-X feature, default 0=disabled */
+#define IFE_PMC_FORCE_MDIX 0x0040 /* 1=force MDIX-X, 0=force MDI */
+#define IFE_PMC_MDIX_STATUS 0x0020 /* 1=MDI-X, 0=MDI */
+#define IFE_PMC_AUTO_MDIX_COMPLETE 0x0010 /* Resolution algorthm is completed */
+#define IFE_PMC_MDIX_MODE_SHIFT 6
+#define IFE_PHC_MDIX_RESET_ALL_MASK 0x0000 /* Disable auto MDI-X */
+
+#define IFE_PHC_HWI_ENABLE 0x8000 /* Enable the HWI feature */
+#define IFE_PHC_ABILITY_CHECK 0x4000 /* 1= Test Passed, 0=failed */
+#define IFE_PHC_TEST_EXEC 0x2000 /* PHY launch test pulses on the wire */
+#define IFE_PHC_HIGHZ 0x0200 /* 1 = Open Circuit */
+#define IFE_PHC_LOWZ 0x0400 /* 1 = Short Circuit */
+#define IFE_PHC_LOW_HIGH_Z_MASK 0x0600 /* Mask for indication type of problem on the line */
+#define IFE_PHC_DISTANCE_MASK 0x01FF /* Mask for distance to the cable problem, in 80cm granularity */
+#define IFE_PHC_RESET_ALL_MASK 0x0000 /* Disable HWI */
+#define IFE_PSCL_PROBE_MODE 0x0020 /* LED Probe mode */
+#define IFE_PSCL_PROBE_LEDS_OFF 0x0006 /* Force LEDs 0 and 2 off */
+#define IFE_PSCL_PROBE_LEDS_ON 0x0007 /* Force LEDs 0 and 2 on */
+
+#define ICH8_FLASH_COMMAND_TIMEOUT 500 /* 500 ms , should be adjusted */
+#define ICH8_FLASH_CYCLE_REPEAT_COUNT 10 /* 10 cycles , should be adjusted */
+#define ICH8_FLASH_SEG_SIZE_256 256
+#define ICH8_FLASH_SEG_SIZE_4K 4096
+#define ICH8_FLASH_SEG_SIZE_64K 65536
+
+#define ICH8_CYCLE_READ 0x0
+#define ICH8_CYCLE_RESERVED 0x1
+#define ICH8_CYCLE_WRITE 0x2
+#define ICH8_CYCLE_ERASE 0x3
+
+#define ICH8_FLASH_GFPREG 0x0000
+#define ICH8_FLASH_HSFSTS 0x0004
+#define ICH8_FLASH_HSFCTL 0x0006
+#define ICH8_FLASH_FADDR 0x0008
+#define ICH8_FLASH_FDATA0 0x0010
+#define ICH8_FLASH_FRACC 0x0050
+#define ICH8_FLASH_FREG0 0x0054
+#define ICH8_FLASH_FREG1 0x0058
+#define ICH8_FLASH_FREG2 0x005C
+#define ICH8_FLASH_FREG3 0x0060
+#define ICH8_FLASH_FPR0 0x0074
+#define ICH8_FLASH_FPR1 0x0078
+#define ICH8_FLASH_SSFSTS 0x0090
+#define ICH8_FLASH_SSFCTL 0x0092
+#define ICH8_FLASH_PREOP 0x0094
+#define ICH8_FLASH_OPTYPE 0x0096
+#define ICH8_FLASH_OPMENU 0x0098
+
+#define ICH8_FLASH_REG_MAPSIZE 0x00A0
+#define ICH8_FLASH_SECTOR_SIZE 4096
+#define ICH8_GFPREG_BASE_MASK 0x1FFF
+#define ICH8_FLASH_LINEAR_ADDR_MASK 0x00FFFFFF
+
+/* ICH8 GbE Flash Hardware Sequencing Flash Status Register bit breakdown */
+/* Offset 04h HSFSTS */
+union ich8_hws_flash_status {
+ struct ich8_hsfsts {
+#ifdef E1000_BIG_ENDIAN
+ uint16_t reserved2 :6;
+ uint16_t fldesvalid :1;
+ uint16_t flockdn :1;
+ uint16_t flcdone :1;
+ uint16_t flcerr :1;
+ uint16_t dael :1;
+ uint16_t berasesz :2;
+ uint16_t flcinprog :1;
+ uint16_t reserved1 :2;
+#else
+ uint16_t flcdone :1; /* bit 0 Flash Cycle Done */
+ uint16_t flcerr :1; /* bit 1 Flash Cycle Error */
+ uint16_t dael :1; /* bit 2 Direct Access error Log */
+ uint16_t berasesz :2; /* bit 4:3 Block/Sector Erase Size */
+ uint16_t flcinprog :1; /* bit 5 flash SPI cycle in Progress */
+ uint16_t reserved1 :2; /* bit 13:6 Reserved */
+ uint16_t reserved2 :6; /* bit 13:6 Reserved */
+ uint16_t fldesvalid :1; /* bit 14 Flash Descriptor Valid */
+ uint16_t flockdn :1; /* bit 15 Flash Configuration Lock-Down */
+#endif
+ } hsf_status;
+ uint16_t regval;
+};
+
+/* ICH8 GbE Flash Hardware Sequencing Flash control Register bit breakdown */
+/* Offset 06h FLCTL */
+union ich8_hws_flash_ctrl {
+ struct ich8_hsflctl {
+#ifdef E1000_BIG_ENDIAN
+ uint16_t fldbcount :2;
+ uint16_t flockdn :6;
+ uint16_t flcgo :1;
+ uint16_t flcycle :2;
+ uint16_t reserved :5;
+#else
+ uint16_t flcgo :1; /* 0 Flash Cycle Go */
+ uint16_t flcycle :2; /* 2:1 Flash Cycle */
+ uint16_t reserved :5; /* 7:3 Reserved */
+ uint16_t fldbcount :2; /* 9:8 Flash Data Byte Count */
+ uint16_t flockdn :6; /* 15:10 Reserved */
+#endif
+ } hsf_ctrl;
+ uint16_t regval;
+};
+
+/* ICH8 Flash Region Access Permissions */
+union ich8_hws_flash_regacc {
+ struct ich8_flracc {
+#ifdef E1000_BIG_ENDIAN
+ uint32_t gmwag :8;
+ uint32_t gmrag :8;
+ uint32_t grwa :8;
+ uint32_t grra :8;
+#else
+ uint32_t grra :8; /* 0:7 GbE region Read Access */
+ uint32_t grwa :8; /* 8:15 GbE region Write Access */
+ uint32_t gmrag :8; /* 23:16 GbE Master Read Access Grant */
+ uint32_t gmwag :8; /* 31:24 GbE Master Write Access Grant */
+#endif
+ } hsf_flregacc;
+ uint16_t regval;
+};
+
/* Miscellaneous PHY bit definitions. */
#define PHY_PREAMBLE 0xFFFFFFFF
#define PHY_SOF 0x01
diff --git a/drivers/net/e1000/e1000_osdep.h b/drivers/net/e1000/e1000_osdep.h
index 6130a42..78f54e3 100644
--- a/drivers/net/e1000/e1000_osdep.h
+++ b/drivers/net/e1000/e1000_osdep.h
@@ -130,4 +130,17 @@ typedef enum {
#define E1000_WRITE_FLUSH(a) E1000_READ_REG(a, STATUS)
+#define E1000_WRITE_ICH8_REG(a, reg, value) ( \
+ writel((value), ((a)->flash_address + reg)))
+
+#define E1000_READ_ICH8_REG(a, reg) ( \
+ readl((a)->flash_address + reg))
+
+#define E1000_WRITE_ICH8_REG16(a, reg, value) ( \
+ writew((value), ((a)->flash_address + reg)))
+
+#define E1000_READ_ICH8_REG16(a, reg) ( \
+ readw((a)->flash_address + reg))
+
+
#endif /* _E1000_OSDEP_H_ */
--
Auke Kok <auke-jan.h.kok@intel.com>
next prev parent reply other threads:[~2006-06-22 5:14 UTC|newest]
Thread overview: 47+ messages / expand[flat|nested] mbox.gz Atom feed top
2006-06-22 5:18 [PATCH 00/21] e1000: driver update to 7.1.9-k2 Kok, Auke
2006-06-22 5:20 ` [PATCH 01/21] e1000: fix loopback ethtool test Kok, Auke
2006-06-22 5:20 ` [PATCH 02/21] e1000: rework driver hardware reset locking Kok, Auke
2006-06-27 1:42 ` Jeff Garzik
2006-06-27 14:42 ` Auke Kok
2006-06-22 5:20 ` [PATCH 03/21] e1000: Make PHY powerup/down a function Kok, Auke
2006-06-22 5:20 ` [PATCH 04/21] e1000: fix CONFIG_PM blocks Kok, Auke
2006-06-22 5:20 ` [PATCH 05/21] e1000: small performance tweak by removing double code Kok, Auke
2006-06-22 5:20 ` [PATCH 06/21] e1000: add smart power down code Kok, Auke
2006-06-27 1:43 ` Jeff Garzik
2006-06-27 8:49 ` Florian Reitmeir
2006-06-27 14:40 ` Auke Kok
2006-06-22 5:20 ` [PATCH 07/21] e1000: change printk into DPRINTK Kok, Auke
2006-06-22 5:20 ` [PATCH 08/21] e1000: recycle skb Kok, Auke
2006-06-22 5:20 ` [PATCH 09/21] e1000: rework module param code with uninitialized values Kok, Auke
2006-06-22 5:20 ` [PATCH 10/21] e1000: force register write flushes to circumvent broken platforms Kok, Auke
2006-06-27 1:47 ` Jeff Garzik
2006-06-27 14:36 ` Auke Kok
2006-06-27 15:41 ` Jeff Garzik
2006-06-27 15:56 ` Auke Kok
2006-06-22 5:20 ` [PATCH 11/21] e1000: disable CRC stripping workaround Kok, Auke
2006-06-22 5:31 ` Ben Greear
2006-06-22 15:36 ` Auke Kok
2006-06-22 15:39 ` Jesse Brandeburg
2006-06-22 15:55 ` Ben Greear
2006-06-22 16:01 ` Jesse Brandeburg
2006-06-22 15:57 ` Lennert Buytenhek
2006-06-27 1:48 ` Jeff Garzik
2006-06-27 14:29 ` Auke Kok
2006-06-22 5:20 ` [PATCH 12/21] e1000: fix adapter led blinking inconsistency Kok, Auke
2006-06-22 5:20 ` [PATCH 13/21] e1000: add E1000_BIG_ENDIAN symbol Kok, Auke
2006-06-27 1:49 ` Jeff Garzik
2006-06-27 14:25 ` Auke Kok
2006-06-22 5:20 ` [PATCH 14/21] e1000: M88 PHY workaround Kok, Auke
2006-06-22 5:20 ` [PATCH 15/21] e1000: check return value of _get_speed_and_duplex Kok, Auke
2006-06-22 5:20 ` [PATCH 16/21] e1000: disable ERT Kok, Auke
2006-06-22 5:20 ` Kok, Auke [this message]
2006-06-27 1:52 ` [PATCH 17/21] e1000: add ich8lan core functions Jeff Garzik
2006-06-27 16:12 ` Auke Kok
2006-06-22 5:20 ` [PATCH 18/21] e1000: integrate ich8 support into driver Kok, Auke
2006-06-27 1:54 ` Jeff Garzik
2006-06-22 5:20 ` [PATCH 19/21] e1000: allow user to disable ich8 lock loss workaround Kok, Auke
2006-06-27 1:55 ` Jeff Garzik
2006-06-27 14:21 ` Auke Kok
2006-06-22 5:20 ` [PATCH 20/21] e1000: add ich8lan device ID's Kok, Auke
2006-06-22 5:20 ` [PATCH 21/21] e1000: increase version to 7.1.9-k2 Kok, Auke
2006-06-27 22:48 ` [PATCH 00/21] e1000: driver update " Auke Kok
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20060622052043.25497.85145.stgit@gitlost.site \
--to=auke-jan.h.kok@intel.com \
--cc=auke@foo-projects.org \
--cc=jesse.brandeburg@intel.com \
--cc=jgarzik@pobox.com \
--cc=john.ronciak@intel.com \
--cc=netdev@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.