* [U-Boot-Users] [RFC] nboot - load from partition
2006-08-03 13:20 [U-Boot-Users] [RFC] nboot - load from partition Ladislav Michl
@ 2006-08-04 14:16 ` Ladislav Michl
0 siblings, 0 replies; 2+ messages in thread
From: Ladislav Michl @ 2006-08-04 14:16 UTC (permalink / raw)
To: u-boot
On Thu, Aug 03, 2006 at 03:20:49PM +0200, Ladislav Michl wrote:
> Hi,
>
> currently nboot command is able to load kernel from given ofset of given
> nand chip. I hope others would find useful if it could load kernel from
> given partition, too. What about
> nboot.part - load from current partition (given by partition variable)
> nboot.part [part_name]
nboot.part is not necessary, so droped.
> Comments and suggestions welcome and appreciated. Especialy ideas for
> some nice command name :-)
I'm leaving for one week holiday, please give it a try.
Best regards,
ladis
diff --git a/common/env_nand.c b/common/env_nand.c
index 0a05b09..4e92d3f 100644
--- a/common/env_nand.c
+++ b/common/env_nand.c
@@ -146,7 +146,7 @@ int saveenv(void)
int ret = 0;
puts ("Erasing Nand...");
- if (nand_erase(&nand_info[0], CFG_ENV_OFFSET, CFG_ENV_SIZE))
+ if (nand_erase(&nand_info[0], CFG_ENV_OFFSET, CFG_ENV_SIZE, 0))
return 1;
puts ("Writing to Nand... ");
diff --git a/include/nand.h b/include/nand.h
index 905115b..ccac9c1 100644
--- a/include/nand.h
+++ b/include/nand.h
@@ -48,7 +48,7 @@ static inline int nand_block_isbad(nand_
return info->block_isbad(info, ofs);
}
-static inline int nand_erase(nand_info_t *info, ulong off, ulong size)
+static inline int nand_erase(nand_info_t *info, ulong off, ulong size, int clean)
{
struct erase_info instr;
@@ -57,7 +57,7 @@ static inline int nand_erase(nand_info_t
instr.len = size;
instr.callback = 0;
- return info->erase(info, &instr);
+ return nand_erase_nand(info, &instr, clean);
}
#endif
diff --git a/common/cmd_nand.c b/common/cmd_nand.c
index 21adb1b..27ee495 100644
--- a/common/cmd_nand.c
+++ b/common/cmd_nand.c
@@ -36,6 +36,15 @@ #endif
#include <jffs2/jffs2.h>
#include <nand.h>
+#if (CONFIG_COMMANDS & CFG_CMD_JFFS2) && defined(CONFIG_JFFS2_CMDLINE)
+
+/* parition handling routines */
+int mtdparts_init(void);
+int id_parse(const char *id, const char **ret_id, u8 *dev_type, u8 *dev_num);
+int find_dev_and_part(const char *id, struct mtd_device **dev,
+ u8 *part_num, struct part_info **part);
+#endif
+
extern nand_info_t nand_info[]; /* info for NAND chips */
static int nand_dump_oob(nand_info_t *nand, ulong off)
@@ -83,50 +92,58 @@ static int nand_dump(nand_info_t *nand,
/* ------------------------------------------------------------------------- */
-static void
-arg_off_size(int argc, char *argv[], ulong *off, ulong *size, ulong totsize)
+static int str2long(char *p, ulong *num)
{
- *off = 0;
- *size = 0;
-
-#if defined(CONFIG_JFFS2_NAND) && defined(CFG_JFFS_CUSTOM_PART)
- if (argc >= 1 && strcmp(argv[0], "partition") == 0) {
- int part_num;
- struct part_info *part;
- const char *partstr;
+ char *endptr;
- if (argc >= 2)
- partstr = argv[1];
- else
- partstr = getenv("partition");
-
- if (partstr)
- part_num = (int)simple_strtoul(partstr, NULL, 10);
- else
- part_num = 0;
+ *num = simple_strtoul(p, &endptr, 16);
+ return (*p != '\0' && *endptr == '\0') ? 1 : 0;
+}
- part = jffs2_part_info(part_num);
- if (part == NULL) {
- printf("\nInvalid partition %d\n", part_num);
- return;
+static int
+arg_off_size(int argc, char *argv[], nand_info_t *nand, ulong *off, ulong *size)
+{
+ int idx = nand_curr_device;
+#if (CONFIG_COMMANDS & CFG_CMD_JFFS2) && defined(CONFIG_JFFS2_CMDLINE)
+ struct mtd_device *dev;
+ struct part_info *part;
+ u8 pnum;
+
+ if (argc == 1 && !(str2long(argv[0], off))) {
+ if ((mtdparts_init() == 0) &&
+ (find_dev_and_part(argv[0], &dev, &pnum, &part) == 0)) {
+ if (dev->id->type != MTD_DEV_TYPE_NAND) {
+ puts("not a NAND device\n");
+ return 1;
+ }
+ *off = part->offset;
+ *size = part->size;
+ idx = dev->id->num;
+ *nand = nand_info[idx];
+ goto out;
}
- *size = part->size;
- *off = (ulong)part->offset;
- } else
+ }
#endif
- {
- if (argc >= 1)
- *off = (ulong)simple_strtoul(argv[0], NULL, 16);
- else
- *off = 0;
- if (argc >= 2)
- *size = (ulong)simple_strtoul(argv[1], NULL, 16);
- else
- *size = totsize - *off;
+ if (argc >= 1) {
+ if (!(str2long(argv[0], off))) {
+ printf("'%s' is not a number\n", argv[0]);
+ return 1;
+ }
+ } else
+ *off = 0;
- }
+ if (argc >= 2) {
+ if (!(str2long(argv[1], size))) {
+ printf("'%s' is not a number\n", argv[1]);
+ return 1;
+ }
+ } else
+ *size = nand->size - *off;
+out:
+ printf("device %d offset 0x%x, size 0x%x ", idx, *off, *size);
+ return 0;
}
int do_nand(cmd_tbl_t * cmdtp, int flag, int argc, char *argv[])
@@ -197,14 +214,20 @@ int do_nand(cmd_tbl_t * cmdtp, int flag,
return 0;
}
+ /*
+ * Syntax is:
+ * 0 1 2 3 4
+ * nand erase [clean] [off size]
+ */
if (strcmp(cmd, "erase") == 0) {
- arg_off_size(argc - 2, argv + 2, &off, &size, nand->size);
- if (off == 0 && size == 0)
+ /* "clean" at index 2 means request to erase OOB */
+ int clean = (argc > 2 && strcmp(argv[2], "clean") == 0) ? 1 : 0;
+ int o = clean ? 3 : 2;
+ puts("\nNAND erase: ");
+ /* skip first two or three arguments, look for offset and size */
+ if (arg_off_size(argc - o, argv + o, nand, &off, &size) != 0)
return 1;
-
- printf("\nNAND erase: device %d offset 0x%x, size 0x%x ",
- nand_curr_device, off, size);
- ret = nand_erase(nand, off, size);
+ ret = nand_erase(nand, off, size, clean);
printf("%s\n", ret ? "ERROR" : "OK");
return ret == 0 ? 0 : 1;
@@ -241,13 +264,10 @@ int do_nand(cmd_tbl_t * cmdtp, int flag,
*/
addr = (ulong)simple_strtoul(argv[2], NULL, 16);
- arg_off_size(argc - 3, argv + 3, &off, &size, nand->size);
- if (off == 0 && size == 0)
- return 1;
-
i = strncmp(cmd, "read", 4) == 0; /* 1 = read, 0 = write */
- printf("\nNAND %s: device %d offset %u, size %u ... ",
- i ? "read" : "write", nand_curr_device, off, size);
+ printf("\nNAND %s: ", i ? "read" : "write");
+ if (arg_off_size(argc - 3, argv + 3, nand, &off, &size) != 0)
+ return 1;
if (i)
ret = nand_read(nand, off, &size, (u_char *)addr);
@@ -275,66 +295,23 @@ U_BOOT_CMD(nand, 5, 1, do_nand,
" offset `off' (entire device if not specified)\n"
"nand bad - show bad blocks\n"
"nand dump[.oob] off - dump page\n"
- "nand scrub - really clean NAND erasing bad blocks (UNSAFE)\n"
"nand markbad off - mark bad block at offset (UNSAFE)\n"
"nand biterr off - make a bit error at offset (UNSAFE)\n");
-int do_nandboot(cmd_tbl_t * cmdtp, int flag, int argc, char *argv[])
+static int nand_load_image(cmd_tbl_t *cmdtp, nand_info_t *nand,
+ ulong offset, ulong addr, char *cmd)
{
- char *boot_device = NULL;
- char *ep;
- int dev;
int r;
- ulong addr, cnt, offset = 0;
+ char *ep;
+ ulong cnt;
image_header_t *hdr;
- nand_info_t *nand;
- switch (argc) {
- case 1:
- addr = CFG_LOAD_ADDR;
- boot_device = getenv("bootdevice");
- break;
- case 2:
- addr = simple_strtoul(argv[1], NULL, 16);
- boot_device = getenv("bootdevice");
- break;
- case 3:
- addr = simple_strtoul(argv[1], NULL, 16);
- boot_device = argv[2];
- break;
- case 4:
- addr = simple_strtoul(argv[1], NULL, 16);
- boot_device = argv[2];
- offset = simple_strtoul(argv[3], NULL, 16);
- break;
- default:
- printf("Usage:\n%s\n", cmdtp->usage);
- SHOW_BOOT_PROGRESS(-1);
- return 1;
- }
-
- if (!boot_device) {
- puts("\n** No boot device **\n");
- SHOW_BOOT_PROGRESS(-1);
- return 1;
- }
-
- dev = simple_strtoul(boot_device, &ep, 16);
-
- if (dev < 0 || dev >= CFG_MAX_NAND_DEVICE || !nand_info[dev].name) {
- printf("\n** Device %d not available\n", dev);
- SHOW_BOOT_PROGRESS(-1);
- return 1;
- }
-
- nand = &nand_info[dev];
- printf("\nLoading from device %d: %s (offset 0x%lx)\n",
- dev, nand->name, offset);
+ printf("\nLoading from %s, offset 0x%lx\n", nand->name, offset);
cnt = nand->oobblock;
r = nand_read(nand, offset, &cnt, (u_char *) addr);
if (r) {
- printf("** Read error on %d\n", dev);
+ puts("** Read error\n");
SHOW_BOOT_PROGRESS(-1);
return 1;
}
@@ -353,7 +330,7 @@ int do_nandboot(cmd_tbl_t * cmdtp, int f
r = nand_read(nand, offset, &cnt, (u_char *) addr);
if (r) {
- printf("** Read error on %d\n", dev);
+ puts("** Read error\n");
SHOW_BOOT_PROGRESS(-1);
return 1;
}
@@ -367,7 +344,7 @@ int do_nandboot(cmd_tbl_t * cmdtp, int f
char *local_args[2];
extern int do_bootm(cmd_tbl_t *, int, int, char *[]);
- local_args[0] = argv[0];
+ local_args[0] = cmd;
local_args[1] = NULL;
printf("Automatic boot of image at addr 0x%08lx ...\n", addr);
@@ -378,9 +355,81 @@ int do_nandboot(cmd_tbl_t * cmdtp, int f
return 0;
}
-U_BOOT_CMD(nboot, 4, 1, do_nandboot,
- "nboot - boot from NAND device\n", "loadAddr dev\n");
+int do_nandboot(cmd_tbl_t * cmdtp, int flag, int argc, char *argv[])
+{
+ char *boot_device = NULL;
+ int idx;
+ ulong addr, offset = 0;
+#if (CONFIG_COMMANDS & CFG_CMD_JFFS2) && defined(CONFIG_JFFS2_CMDLINE)
+ struct mtd_device *dev;
+ struct part_info *part;
+ u8 pnum;
+
+ if (argc >= 2) {
+ char *p = (argc == 2) ? argv[1] : argv[2];
+ if (!(str2long(p, &addr)) && (mtdparts_init() == 0) &&
+ (find_dev_and_part(p, &dev, &pnum, &part) == 0)) {
+ if (dev->id->type != MTD_DEV_TYPE_NAND) {
+ puts("Not a NAND device\n");
+ return 1;
+ }
+ if (argc > 3)
+ goto usage;
+ if (argc == 3)
+ addr = simple_strtoul(argv[2], NULL, 16);
+ else
+ addr = CFG_LOAD_ADDR;
+ return nand_load_image(cmdtp, &nand_info[dev->id->num],
+ part->offset, addr, argv[0]);
+ }
+ }
+#endif
+ switch (argc) {
+ case 1:
+ addr = CFG_LOAD_ADDR;
+ boot_device = getenv("bootdevice");
+ break;
+ case 2:
+ addr = simple_strtoul(argv[1], NULL, 16);
+ boot_device = getenv("bootdevice");
+ break;
+ case 3:
+ addr = simple_strtoul(argv[1], NULL, 16);
+ boot_device = argv[2];
+ break;
+ case 4:
+ addr = simple_strtoul(argv[1], NULL, 16);
+ boot_device = argv[2];
+ offset = simple_strtoul(argv[3], NULL, 16);
+ break;
+ default:
+usage:
+ printf("Usage:\n%s\n", cmdtp->usage);
+ SHOW_BOOT_PROGRESS(-1);
+ return 1;
+ }
+
+ if (!boot_device) {
+ puts("\n** No boot device **\n");
+ SHOW_BOOT_PROGRESS(-1);
+ return 1;
+ }
+
+ idx = simple_strtoul(boot_device, NULL, 16);
+
+ if (idx < 0 || idx >= CFG_MAX_NAND_DEVICE || !nand_info[idx].name) {
+ printf("\n** Device %d not available\n", idx);
+ SHOW_BOOT_PROGRESS(-1);
+ return 1;
+ }
+
+ return nand_load_image(cmdtp, &nand_info[idx], offset, addr, argv[0]);
+}
+
+U_BOOT_CMD(nboot, 4, 1, do_nandboot,
+ "nboot - boot from NAND device\n",
+ "[partition] | [[[load_addr] dev] offset]\n");
#endif /* (CONFIG_COMMANDS & CFG_CMD_NAND) */
^ permalink raw reply related [flat|nested] 2+ messages in thread