* [lm-sensors] Some W83627HG-AW chip
@ 2007-04-25 8:42 Láďa
2007-04-26 12:07 ` Jean Delvare
2007-04-26 21:23 ` Láďa
0 siblings, 2 replies; 3+ messages in thread
From: Láďa @ 2007-04-25 8:42 UTC (permalink / raw)
To: lm-sensors
W83627HG-AW is another surprise from SuperMicro, there should be W8327EHG on
board (they are not so precise). Here is some output from sensors-detect:
Driver `w83793' (should be inserted):
Detects correctly:
* Bus `SMBus I801 adapter at 1100'
Busdriver `i2c-i801', I2C address 0x2f
Chip `Winbond W83793R/G' (confidence: 8)
.....
Driver `w83781d' (should be inserted):
Detects correctly:
* ISA bus address 0x0290 (Busdriver `i2c-isa')
Chip `Winbond W83627HF' (confidence: 8)
Driver `w83627hf' (should be inserted):
Detects correctly:
* ISA bus address 0x0295 (Busdriver `i2c-isa')
Chip `Winbond W83627HF Super IO Sensors' (confidence: 9)
both modules are compiled in kernel, but sensors doesn't show useful output:
w83627hf-isa-0290
Adapter: ISA adapter
VCore 1: +0.03 V (min = +1.09 V, max = +1.50 V) ALARM
VCore 2: +0.05 V (min = +1.09 V, max = +1.50 V) ALARM
+3.3V: +0.05 V (min = +2.82 V, max = +3.79 V) ALARM
+5V: +5.08 V (min = +1.10 V, max = +4.89 V) ALARM
+12V: +0.12 V (min = +13.80 V, max = +0.55 V) ALARM
-12V: -14.66 V (min = -1.01 V, max = +1.37 V) ALARM
-5V: -7.56 V (min = -6.00 V, max = -1.98 V) ALARM
V5SB: +5.59 V (min = +4.78 V, max = +0.59 V) ALARM
VBat: +3.36 V (min = +3.78 V, max = +2.19 V) ALARM
fan1: 0 RPM (min = 0 RPM, div = 2)
fan2: 0 RPM (min = 8766 RPM, div = 2) ALARM
fan3: 0 RPM (min = 3054 RPM, div = 2) ALARM
temp1: +126 C (high = +26 C, hyst = -86 C) sensor = thermistor
ALARM
temp2: +126.5 C (high = +80 C, hyst = +75 C) sensor = thermistor
ALARM
temp3: +126.5 C (high = +80 C, hyst = +75 C) sensor = thermistor
ALARM
vid: +1.519 V (VRM Version 11.0)
alarms: Chassis intrusion detection ALARM
beep_enable:
Sound alarm enabled
I am using Gentoo Linux, gentoo-sources-2.6.19, architecture amd64. Btw. I
was a bit surprised that amd64 kernel is missing CONFIG_ISA option, but
needed i2c-isa seems to be compiled well according to kernel make output:
CC drivers/i2c/busses/i2c-isa.o
Any idea how to get this working? :-)
Regards
L·Ôa
_______________________________________________
lm-sensors mailing list
lm-sensors@lm-sensors.org
http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: [lm-sensors] Some W83627HG-AW chip
2007-04-25 8:42 [lm-sensors] Some W83627HG-AW chip Láďa
@ 2007-04-26 12:07 ` Jean Delvare
2007-04-26 21:23 ` Láďa
1 sibling, 0 replies; 3+ messages in thread
From: Jean Delvare @ 2007-04-26 12:07 UTC (permalink / raw)
To: lm-sensors
Hi Láďa,
On Wed, 25 Apr 2007 10:42:04 +0200, Láďa wrote:
> W83627HG-AW is another surprise from SuperMicro, there should be W8327EHG on
> board (they are not so precise). Here is some output from sensors-detect:
>
> Driver `w83793' (should be inserted):
> Detects correctly:
> * Bus `SMBus I801 adapter at 1100'
> Busdriver `i2c-i801', I2C address 0x2f
> Chip `Winbond W83793R/G' (confidence: 8)
> .....
> Driver `w83781d' (should be inserted):
> Detects correctly:
> * ISA bus address 0x0290 (Busdriver `i2c-isa')
> Chip `Winbond W83627HF' (confidence: 8)
> Driver `w83627hf' (should be inserted):
> Detects correctly:
> * ISA bus address 0x0295 (Busdriver `i2c-isa')
> Chip `Winbond W83627HF Super IO Sensors' (confidence: 9)
>
> both modules are compiled in kernel, but sensors doesn't show useful output:
Which "both"? There are three kernel modules listed above, w83793,
w83781d and w83627hf. The sensors-detect script is wrongly suggesting
two drivers for the same device. This is fixed by now, I guess you are
using a somewhat old version of the script.
So the bottom line is that you should NOT use the w83781d driver.
>
> w83627hf-isa-0290
> Adapter: ISA adapter
> VCore 1: +0.03 V (min = +1.09 V, max = +1.50 V) ALARM
> VCore 2: +0.05 V (min = +1.09 V, max = +1.50 V) ALARM
> +3.3V: +0.05 V (min = +2.82 V, max = +3.79 V) ALARM
> +5V: +5.08 V (min = +1.10 V, max = +4.89 V) ALARM
> +12V: +0.12 V (min = +13.80 V, max = +0.55 V) ALARM
> -12V: -14.66 V (min = -1.01 V, max = +1.37 V) ALARM
> -5V: -7.56 V (min = -6.00 V, max = -1.98 V) ALARM
> V5SB: +5.59 V (min = +4.78 V, max = +0.59 V) ALARM
> VBat: +3.36 V (min = +3.78 V, max = +2.19 V) ALARM
> fan1: 0 RPM (min = 0 RPM, div = 2)
> fan2: 0 RPM (min = 8766 RPM, div = 2) ALARM
> fan3: 0 RPM (min = 3054 RPM, div = 2) ALARM
> temp1: +126 C (high = +26 C, hyst = -86 C) sensor = thermistor
> ALARM
> temp2: +126.5 C (high = +80 C, hyst = +75 C) sensor = thermistor
> ALARM
> temp3: +126.5 C (high = +80 C, hyst = +75 C) sensor = thermistor
> ALARM
> vid: +1.519 V (VRM Version 11.0)
> alarms: Chassis intrusion detection ALARM
> beep_enable:
> Sound alarm enabled
>
> I am using Gentoo Linux, gentoo-sources-2.6.19, architecture amd64. Btw. I
> was a bit surprised that amd64 kernel is missing CONFIG_ISA option, but
> needed i2c-isa seems to be compiled well according to kernel make output:
>
> CC drivers/i2c/busses/i2c-isa.o
There are no ISA slots on x86_64 motherboards, so no CONFIG_ISA option,
but an ISA-like I/O space is still present so i2c-isa works.
> Any idea how to get this working? :-)
The output above strongly suggests that the W83627HF Super-I/O chip is
not wired for hardware monitoring. As you can see, all values except
V5SB and VBat are broken or missing.
Given that the motherboard appears to have a dedicated hardware
monitoring chip (W83793) it makes sense that Supermicro did not use the
hardware monitoring functions of the Super-I/O. So you want to unload
the w83267hf driver (or add ignore statements for everything but the
two working voltage lines in sensors.conf) and load the w83793 driver
instead. Except that this driver is new in 2.6.20, as can be seen on
our wiki:
http://www.lm-sensors.org/wiki/Devices
So you'll need to upgrade your kernel before you can monitor the
temperatures and fans on this motherboard.
--
Jean Delvare
_______________________________________________
lm-sensors mailing list
lm-sensors@lm-sensors.org
http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: [lm-sensors] Some W83627HG-AW chip
2007-04-25 8:42 [lm-sensors] Some W83627HG-AW chip Láďa
2007-04-26 12:07 ` Jean Delvare
@ 2007-04-26 21:23 ` Láďa
1 sibling, 0 replies; 3+ messages in thread
From: Láďa @ 2007-04-26 21:23 UTC (permalink / raw)
To: lm-sensors
Hi,
And thanks for reply... I have fixed this already with help from Winbond
guys (thanks again). You are right, correct driver was w83793, kernel
upgrade solved this and sensors are working nice now.
Láïa
> -----Original Message-----
> From: Jean Delvare [mailto:khali@linux-fr.org]
> Sent: Thursday, April 26, 2007 2:07 PM
> To: Láïa
> Cc: lm-sensors@lm-sensors.org
> Subject: Re: [lm-sensors] Some W83627HG-AW chip
>
> Hi Láïa,
>
> On Wed, 25 Apr 2007 10:42:04 +0200, Láïa wrote:
> > W83627HG-AW is another surprise from SuperMicro, there should be
> W8327EHG on
> > board (they are not so precise). Here is some output from sensors-
> detect:
> >
> > Driver `w83793' (should be inserted):
> > Detects correctly:
> > * Bus `SMBus I801 adapter at 1100'
> > Busdriver `i2c-i801', I2C address 0x2f
> > Chip `Winbond W83793R/G' (confidence: 8)
> > .....
> > Driver `w83781d' (should be inserted):
> > Detects correctly:
> > * ISA bus address 0x0290 (Busdriver `i2c-isa')
> > Chip `Winbond W83627HF' (confidence: 8)
> > Driver `w83627hf' (should be inserted):
> > Detects correctly:
> > * ISA bus address 0x0295 (Busdriver `i2c-isa')
> > Chip `Winbond W83627HF Super IO Sensors' (confidence: 9)
> >
> > both modules are compiled in kernel, but sensors doesn't show useful
> output:
>
> Which "both"? There are three kernel modules listed above, w83793,
> w83781d and w83627hf. The sensors-detect script is wrongly suggesting
> two drivers for the same device. This is fixed by now, I guess you are
> using a somewhat old version of the script.
>
> So the bottom line is that you should NOT use the w83781d driver.
>
> >
> > w83627hf-isa-0290
> > Adapter: ISA adapter
> > VCore 1: +0.03 V (min = +1.09 V, max = +1.50 V) ALARM
> > VCore 2: +0.05 V (min = +1.09 V, max = +1.50 V) ALARM
> > +3.3V: +0.05 V (min = +2.82 V, max = +3.79 V) ALARM
> > +5V: +5.08 V (min = +1.10 V, max = +4.89 V) ALARM
> > +12V: +0.12 V (min = +13.80 V, max = +0.55 V) ALARM
> > -12V: -14.66 V (min = -1.01 V, max = +1.37 V) ALARM
> > -5V: -7.56 V (min = -6.00 V, max = -1.98 V) ALARM
> > V5SB: +5.59 V (min = +4.78 V, max = +0.59 V) ALARM
> > VBat: +3.36 V (min = +3.78 V, max = +2.19 V) ALARM
> > fan1: 0 RPM (min = 0 RPM, div = 2)
> > fan2: 0 RPM (min = 8766 RPM, div = 2) ALARM
> > fan3: 0 RPM (min = 3054 RPM, div = 2) ALARM
> > temp1: +126 C (high = +26 C, hyst = -86 C) sensor > thermistor
> > ALARM
> > temp2: +126.5 C (high = +80 C, hyst = +75 C) sensor > thermistor
> > ALARM
> > temp3: +126.5 C (high = +80 C, hyst = +75 C) sensor > thermistor
> > ALARM
> > vid: +1.519 V (VRM Version 11.0)
> > alarms: Chassis intrusion detection ALARM
> > beep_enable:
> > Sound alarm enabled
> >
> > I am using Gentoo Linux, gentoo-sources-2.6.19, architecture amd64. Btw.
> I
> > was a bit surprised that amd64 kernel is missing CONFIG_ISA option, but
> > needed i2c-isa seems to be compiled well according to kernel make
> output:
> >
> > CC drivers/i2c/busses/i2c-isa.o
>
> There are no ISA slots on x86_64 motherboards, so no CONFIG_ISA option,
> but an ISA-like I/O space is still present so i2c-isa works.
>
> > Any idea how to get this working? :-)
>
> The output above strongly suggests that the W83627HF Super-I/O chip is
> not wired for hardware monitoring. As you can see, all values except
> V5SB and VBat are broken or missing.
>
> Given that the motherboard appears to have a dedicated hardware
> monitoring chip (W83793) it makes sense that Supermicro did not use the
> hardware monitoring functions of the Super-I/O. So you want to unload
> the w83267hf driver (or add ignore statements for everything but the
> two working voltage lines in sensors.conf) and load the w83793 driver
> instead. Except that this driver is new in 2.6.20, as can be seen on
> our wiki:
> http://www.lm-sensors.org/wiki/Devices
>
> So you'll need to upgrade your kernel before you can monitor the
> temperatures and fans on this motherboard.
>
> --
> Jean Delvare
_______________________________________________
lm-sensors mailing list
lm-sensors@lm-sensors.org
http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2007-04-26 21:23 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2007-04-25 8:42 [lm-sensors] Some W83627HG-AW chip Láďa
2007-04-26 12:07 ` Jean Delvare
2007-04-26 21:23 ` Láďa
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.