hda-intel without headphone output

hda-intel without headphone output

[Robert Lemmen]

hi everyone,

i have a fujitsu siemens amilo pro v3515 notebook, with a via VT8251/
VT8237A chipset. sound works fine through the speakers, but i don't get
anything through the headphones, no headphone channel shows up in the
mixer, and the headphone jack switch doesn't mute the speakers. i have
alsa 1.0.13, and a 2.6.18 kernel. i tried all "model" settings that i
could find in ALSA-Configuration in the kernel tree. lspci -nv gives

04:01.0 0403: 1106:3288 (rev 10)
        Subsystem: 1734:10cb
        Flags: bus master, fast devsel, latency 0, IRQ 58
        Memory at c9100000 (64-bit, non-prefetchable) [size=16K]
        Capabilities: [50] Power Management version 2
        Capabilities: [60] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
        Capabilities: [70] Express Unknown type IRQ 0

(only the stanza for the sound card, yell if you need more), and /proc/asound/card0/codec#0 gives:

Codec: Generic 14f1 ID 5045
Address: 0
Vendor Id: 0x14f15045
Subsystem Id: 0x173410cb
Revision Id: 0x100100
Default PCM: rates 0x140, bits 0x0e, types 0x1
Default Amp-In caps: N/A
Default Amp-Out caps: N/A
Node 0x10 [Pin Complex] wcaps 0x40058d: Stereo Amp-Out
  Amp-Out caps: ofs=0x2b, nsteps=0x2b, stepsize=0x05, mute=1
  Amp-Out vals:  [0x28 0x28]
  Pincap 0x0810014: OUT EAPD Detect
  Pin Default 0x92170110: [Fixed] Speaker at Int Front
    Conn = Analog, Color = Unknown
  Pin-ctls: 0x40: OUT
  Power: 0x0
  Connection: 2
     0x19* 0x17
Node 0x11 [Pin Complex] wcaps 0x40058d: Stereo Amp-Out
  Amp-Out caps: ofs=0x2b, nsteps=0x2b, stepsize=0x05, mute=1
  Amp-Out vals:  [0x00 0x00]
  Pincap 0x08113c: IN OUT HP Detect
  Pin Default 0x0121401f: [Jack] HP Out at Ext Rear
    Conn = 1/8, Color = Green
  Pin-ctls: 0xc0: OUT HP
  Power: 0x0
  Connection: 2
     0x19* 0x17
Node 0x12 [Pin Complex] wcaps 0x40058d: Stereo Amp-Out
  Amp-Out caps: ofs=0x2b, nsteps=0x2b, stepsize=0x05, mute=1
  Amp-Out vals:  [0xab 0xab]
  Pincap 0x08113c: IN OUT HP Detect
  Pin Default 0x01a19020: [Jack] Mic at Ext Rear
    Conn = 1/8, Color = Pink
  Pin-ctls: 0x20: IN
  Power: 0x0
  Connection: 2
     0x19* 0x17
Node 0x13 [Pin Complex] wcaps 0x400301: Stereo Digital
  Pincap 0x0810: OUT
  Pin Default 0x214571f0: [Jack] SPDIF Out at Sep Rear
    Conn = Optical, Color = Yellow
  Pin-ctls: 0x00:
  Connection: 1
     0x18
Node 0x14 [Pin Complex] wcaps 0x400081: Stereo
  Pincap 0x081124: IN Detect
  Pin Default 0x97a7012e: [Fixed] Mic at Int Riser
    Conn = Analog, Color = Unknown
  Pin-ctls: 0x20: IN
Node 0x15 [Pin Complex] wcaps 0x400001: Stereo
  Pincap 0x0820: IN
  Pin Default 0x400001f0: [N/A] Line Out at Ext N/A
    Conn = Unknown, Color = Unknown
  Pin-ctls: 0x00:
Node 0x16 [Beep Generator Widget] wcaps 0x70000c: Mono Amp-Out
  Amp-Out caps: ofs=0x07, nsteps=0x07, stepsize=0x0b, mute=1
  Amp-Out vals:  [0x06]
Node 0x17 [Audio Mixer] wcaps 0x20050b: Stereo Amp-In
  Amp-In caps: ofs=0x14, nsteps=0x2b, stepsize=0x05, mute=1
  Amp-In vals:  [0x94 0x94] [0x17 0x17] [0x94 0x94] [0x94 0x94] [0x94 0x94]
  Power: 0x0
  Connection: 5
     0x19 0x14 0x12 0x11 0x15
Node 0x18 [Audio Output] wcaps 0x211: Stereo Digital
  PCM: rates 0x040, bits 0x06, types 0x5
Node 0x19 [Audio Output] wcaps 0xc11: Stereo
  PCM: rates 0x540, bits 0x0e, types 0x1
  Power: 0x0
Node 0x1a [Audio Input] wcaps 0x100d0b: Stereo Amp-In
  Amp-In caps: ofs=0x00, nsteps=0x17, stepsize=0x05, mute=1
  Amp-In vals:  [0x17 0x17] [0x00 0x00] [0x00 0x00] [0x00 0x00] [0x00 0x00]
  Power: 0x0
  Connection: 5
     0x17 0x14 0x12 0x11 0x15*
Node 0x1b [Vendor Defined Widget] wcaps 0xf00000: Mono
 
please tell me if there is anything i can do, any additional 
information you need, or any general tipps.

thanks  robert

-- 
Robert Lemmen                               http://www.semistable.com 

Re: hda-intel without headphone output

[Takashi Iwai]

At Thu, 14 Jun 2007 10:31:56 +0200,
Robert Lemmen wrote:
> 
> hi everyone,
> 
> i have a fujitsu siemens amilo pro v3515 notebook, with a via VT8251/
> VT8237A chipset. sound works fine through the speakers, but i don't get
> anything through the headphones, no headphone channel shows up in the
> mixer, and the headphone jack switch doesn't mute the speakers. i have
> alsa 1.0.13, and a 2.6.18 kernel. i tried all "model" settings that i
> could find in ALSA-Configuration in the kernel tree. lspci -nv gives
> 
> 04:01.0 0403: 1106:3288 (rev 10)
>         Subsystem: 1734:10cb
>         Flags: bus master, fast devsel, latency 0, IRQ 58
>         Memory at c9100000 (64-bit, non-prefetchable) [size=16K]
>         Capabilities: [50] Power Management version 2
>         Capabilities: [60] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
>         Capabilities: [70] Express Unknown type IRQ 0
> 
> (only the stanza for the sound card, yell if you need more), and /proc/asound/card0/codec#0 gives:
> 
> Codec: Generic 14f1 ID 5045

The conexant codec is much better supported on ALSA 1.0.14.
Give it a try first.


Takashi

Re: hda-intel without headphone output

[Robert Lemmen]

On Thu, Jun 14, 2007 at 03:41:13PM +0200, Takashi Iwai wrote:
> The conexant codec is much better supported on ALSA 1.0.14.
> Give it a try first.

and i thought my alsa version was recent :P

this did the trick in combination with model=laptop, other models didn't
work. thanks for the help, and if there is any additional information
you need in order to make the driver autodetect the model in future
versions (if such a thing is possible), just tell me.

thanks again  robert

-- 
Robert Lemmen                               http://www.semistable.com 

Re: hda-intel without headphone output

[Tobin Davis]

[-- Attachment #1: Type: text/plain, Size: 850 bytes --]

This patch should take care of your system.

Summary:  hda-codec:  Add Fujitsu Siemens v3515 support to
patch_conexant.

This patch adds support for the Fujitsu Seimens Amilo Pro v3515
notebook.

Signed off by:  Tobin Davis <tdavis@dsl-only.net>

On Thu, 2007-06-14 at 20:27 +0200, Robert Lemmen wrote:

> On Thu, Jun 14, 2007 at 03:41:13PM +0200, Takashi Iwai wrote:
> > The conexant codec is much better supported on ALSA 1.0.14.
> > Give it a try first.
> 
> and i thought my alsa version was recent :P
> 
> this did the trick in combination with model=laptop, other models didn't
> work. thanks for the help, and if there is any additional information
> you need in order to make the driver autodetect the model in future
> versions (if such a thing is possible), just tell me.
> 
> thanks again  robert
> 

-- 
Tobin Davis <tdavis@dsl-only.net>

[-- Attachment #2: conexant-FS3515.patch --]
[-- Type: text/x-patch, Size: 580 bytes --]

diff -r d2662f0d43b1 pci/hda/patch_conexant.c
--- a/pci/hda/patch_conexant.c	Thu May 31 09:09:20 2007 +0200
+++ b/pci/hda/patch_conexant.c	Thu Jun 14 19:22:53 2007 -0700
@@ -802,6 +802,7 @@ static struct snd_pci_quirk cxt5045_cfg_
 	SND_PCI_QUIRK(0x103c, 0x30b5, "HP DV2120", CXT5045_LAPTOP),
 	SND_PCI_QUIRK(0x103c, 0x30cd, "HP DV Series", CXT5045_LAPTOP),
 	SND_PCI_QUIRK(0x1734, 0x10ad, "Fujitsu Si1520", CXT5045_FUJITSU),
+	SND_PCI_QUIRK(0x1734, 0x10cb, "Fujitsu Si3515", CXT5045_FUJITSU),
 	SND_PCI_QUIRK(0x8086, 0x2111, "Conexant Reference board", CXT5045_LAPTOP),
 	{}
 };

[-- Attachment #3: Type: text/plain, Size: 160 bytes --]

_______________________________________________
Alsa-devel mailing list
Alsa-devel@alsa-project.org
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel

Re: hda-intel without headphone output

[Takashi Iwai]

At Thu, 14 Jun 2007 19:26:14 -0700,
Tobin Davis wrote:
> 
> This patch should take care of your system.
> 
> Summary:  hda-codec:  Add Fujitsu Siemens v3515 support to patch_conexant.
> 
> This patch adds support for the Fujitsu Seimens Amilo Pro v3515 notebook.
> 
> Signed off by:  Tobin Davis <tdavis@dsl-only.net>

Applied to HG tree.  Thanks.


Takashi

Re: hda-intel without headphone output

[Robert Lemmen]

On Tue, Jun 19, 2007 at 12:16:10PM +0200, Takashi Iwai wrote:
> > This patch adds support for the Fujitsu Seimens Amilo Pro v3515 notebook.
> > 
> > Signed off by:  Tobin Davis <tdavis@dsl-only.net>
> 
> Applied to HG tree.  Thanks.

perhaps you want to hold it for a while. i tried the patch on my
machine, and it does change the behaviour a bit (when i plug in
headphones both the headphones and the loudspeakers work, before only
the loudspeakers did), but it does not mute the speakers. model=laptop
fixes this. i wasn't 100% sure that i did apply the patch correctly and
did not by accident use the old module, so i didn't report it
immediately. didn't have time to look into it yet, but promise to do so
soonish

cu  robert

-- 
Robert Lemmen                               http://www.semistable.com 

Re: hda-intel without headphone output

[Takashi Iwai]

At Tue, 19 Jun 2007 13:35:25 +0200,
Robert Lemmen wrote:
> 
> On Tue, Jun 19, 2007 at 12:16:10PM +0200, Takashi Iwai wrote:
> > > This patch adds support for the Fujitsu Seimens Amilo Pro v3515 notebook.
> > > 
> > > Signed off by:  Tobin Davis <tdavis@dsl-only.net>
> > 
> > Applied to HG tree.  Thanks.
> 
> perhaps you want to hold it for a while. i tried the patch on my
> machine, and it does change the behaviour a bit (when i plug in
> headphones both the headphones and the loudspeakers work, before only
> the loudspeakers did), but it does not mute the speakers. model=laptop
> fixes this. i wasn't 100% sure that i did apply the patch correctly and
> did not by accident use the old module, so i didn't report it
> immediately. didn't have time to look into it yet, but promise to do so
> soonish

The patch works as if model=fujitsu.  So I suppose model=fujitsu
doesn't work as expected?

Try to replace CXT5045_FUJITSU with CXT5045_LAPTOP in that patch.


Takashi

Re: hda-intel without headphone output

[Robert Lemmen]

On Tue, Jun 19, 2007 at 01:43:25PM +0200, Takashi Iwai wrote:
> The patch works as if model=fujitsu.  So I suppose model=fujitsu
> doesn't work as expected?
> 
> Try to replace CXT5045_FUJITSU with CXT5045_LAPTOP in that patch.

hi everyone,

i am sorry, but this still doesn't work. if i pass model=laptop on the
modprobe line or through /etc/modultils.d/, everything works as
expected, including speaker muting on headphone jack insert. using no
param or fujitsu works, but without muting. perhaps the driver somehow
does not pick up the automatic model setting? is there a way to query a
running driver on which model it did select? or is there a way to add
something like a printf() to an alsa module (just for debugging)? and
lastly: i have no idea how all this stuff works, but looking at the
patch, it looks like you are tying the lspci subsystem id to the model.
in my lspci output i have multiple devices with that subsystem id
(1734:10cb), could that be a problem? full lspci -vn output:

00:00.0 0600: 1106:0364
        Subsystem: 1106:0364
        Flags: medium devsel
        Memory at c0000000 (32-bit, prefetchable) [disabled] [size=128M]
        Capabilities: <access denied>

00:00.1 0600: 1106:1364
        Flags: bus master, medium devsel, latency 0

00:00.2 0600: 1106:2364
        Flags: bus master, medium devsel, latency 0

00:00.3 0600: 1106:3364
        Flags: bus master, medium devsel, latency 0

00:00.4 0600: 1106:4364
        Flags: bus master, medium devsel, latency 0

00:00.5 0800: 1106:5364 (prog-if 20 [IO(X)-APIC])
        Flags: bus master, fast devsel, latency 0

00:00.6 0600: 1106:6364
        Flags: bus master, fast devsel, latency 0

00:00.7 0600: 1106:7364
        Flags: bus master, medium devsel, latency 0

00:01.0 0604: 1106:b198 (prog-if 00 [Normal decode])
        Flags: bus master, 66MHz, medium devsel, latency 0
        Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
        Memory behind bridge: c8000000-c8ffffff
        Prefetchable memory behind bridge: a0000000-bfffffff
        Capabilities: <access denied>

00:02.0 0604: 1106:a364 (rev 80) (prog-if 00 [Normal decode])
        Flags: bus master, fast devsel, latency 0
        Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
        Capabilities: <access denied>

00:03.0 0604: 1106:c364 (rev 80) (prog-if 00 [Normal decode])
        Flags: bus master, fast devsel, latency 0
        Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
        I/O behind bridge: 00007000-00007fff
        Memory behind bridge: c9000000-c90fffff
        Capabilities: <access denied>

00:0f.0 0101: 1106:0591 (rev 80) (prog-if 8f [Master SecP SecO PriP PriO])
        Subsystem: 1734:10cb
        Flags: bus master, medium devsel, latency 64, IRQ 217
        I/O ports at 60b8 [size=8]
        I/O ports at 60b0 [size=4]
        I/O ports at 6008 [size=8]
        I/O ports at 6004 [size=4]
        I/O ports at 6010 [size=16]
        I/O ports at 6400 [size=256]
        Capabilities: <access denied>

00:0f.1 0101: 1106:0571 (rev 07) (prog-if 8a [Master SecP PriP])
        Subsystem: 1734:10cb
        Flags: bus master, medium devsel, latency 0
        I/O ports at 60a0 [size=16]
        Capabilities: <access denied>

00:10.0 0c03: 1106:3038 (rev a0) (prog-if 00 [UHCI])
        Subsystem: 1734:10cb
        Flags: bus master, medium devsel, latency 64, IRQ 233
        I/O ports at 6020 [size=32]
        Capabilities: <access denied>

00:10.1 0c03: 1106:3038 (rev a0) (prog-if 00 [UHCI])
        Subsystem: 1734:10cb
        Flags: bus master, medium devsel, latency 64, IRQ 50
        I/O ports at 6040 [size=32]
        Capabilities: <access denied>

00:10.2 0c03: 1106:3038 (rev a0) (prog-if 00 [UHCI])
        Subsystem: 1734:10cb
        Flags: bus master, medium devsel, latency 64, IRQ 217
        I/O ports at 6060 [size=32]
        Capabilities: <access denied>

00:10.3 0c03: 1106:3038 (rev a0) (prog-if 00 [UHCI])
        Subsystem: 1734:10cb
        Flags: bus master, medium devsel, latency 64, IRQ 225
        I/O ports at 6080 [size=32]
        Capabilities: <access denied>

00:10.4 0c03: 1106:3104 (rev 86) (prog-if 20 [EHCI])
        Subsystem: 1734:10cb
        Flags: bus master, medium devsel, latency 64, IRQ 217
        Memory at c9400000 (32-bit, non-prefetchable) [size=256]
        Capabilities: <access denied>

00:11.0 0601: 1106:3337
        Subsystem: 1734:10cb
        Flags: medium devsel
        Capabilities: <access denied>

00:11.7 0600: 1106:287e
        Subsystem: 1106:337e
        Flags: medium devsel
        Capabilities: <access denied>

00:12.0 0200: 1106:3065 (rev 7c)
        Subsystem: 1734:10cb
        Flags: bus master, medium devsel, latency 24, IRQ 225
        I/O ports at 6800 [size=256]
        Memory at c9400400 (32-bit, non-prefetchable) [size=256]
        Capabilities: <access denied>

00:13.0 0604: 1106:337b (prog-if 00 [Normal decode])
        Flags: bus master, fast devsel, latency 0
        Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
        Memory behind bridge: c9100000-c91fffff
        Capabilities: <access denied>

00:13.1 0604: 1106:337a (prog-if 01 [Subtractive decode])
        Flags: bus master, fast devsel, latency 0
        Bus: primary=00, secondary=05, subordinate=05, sec-latency=0
        Memory behind bridge: 50000000-500fffff
        Capabilities: <access denied>

01:00.0 0300: 1106:3371 (rev 01) (prog-if 00 [VGA])
        Subsystem: 1734:10cb
        Flags: bus master, 66MHz, medium devsel, latency 16, IRQ 9
        Memory at a0000000 (32-bit, prefetchable) [size=512M]
        Memory at c8000000 (32-bit, non-prefetchable) [size=16M]
        Capabilities: <access denied>

04:01.0 0403: 1106:3288 (rev 10)
        Subsystem: 1734:10cb
        Flags: bus master, fast devsel, latency 0, IRQ 58
        Memory at c9100000 (64-bit, non-prefetchable) [size=16K]
        Capabilities: <access denied>

05:01.0 0200: 168c:001a (rev 01)
        Subsystem: 168c:2052
        Flags: bus master, medium devsel, latency 80, IRQ 10
        Memory at 50000000 (32-bit, non-prefetchable) [size=64K]
        Capabilities: <access denied>

cu  robert

-- 
Robert Lemmen                               http://www.semistable.com 

Re: hda-intel without headphone output

[Takashi Iwai]

At Wed, 20 Jun 2007 21:02:40 +0200,
Robert Lemmen wrote:
> 
> On Tue, Jun 19, 2007 at 01:43:25PM +0200, Takashi Iwai wrote:
> > The patch works as if model=fujitsu.  So I suppose model=fujitsu
> > doesn't work as expected?
> > 
> > Try to replace CXT5045_FUJITSU with CXT5045_LAPTOP in that patch.
> 
> hi everyone,
> 
> i am sorry, but this still doesn't work.

Are you sure that you remove model option with that patch?
The model option overrides the default model preset.

>if i pass model=laptop on the
> modprobe line or through /etc/modultils.d/, everything works as
> expected, including speaker muting on headphone jack insert. using no
> param or fujitsu works, but without muting. perhaps the driver somehow
> does not pick up the automatic model setting? is there a way to query a
> running driver on which model it did select? or is there a way to add
> something like a printf() to an alsa module (just for debugging)?

Add printk().

> and
> lastly: i have no idea how all this stuff works, but looking at the
> patch, it looks like you are tying the lspci subsystem id to the model.
> in my lspci output i have multiple devices with that subsystem id
> (1734:10cb), could that be a problem?

No, it looks OK.


Takashi

Re: hda-intel without headphone output

[Robert Lemmen]

On Thu, Jun 21, 2007 at 12:24:23PM +0200, Takashi Iwai wrote:
> > i am sorry, but this still doesn't work.
> 
> Are you sure that you remove model option with that patch?
> The model option overrides the default model preset.

sorry for the confusion, but the second patch i got here (the one where
the model is set to "laptop" in the quirks stuff), actually *does* work
fine. it seems it was a bit late for me, and i got confused with
different versions of the modules under /lib/**.

cu  robert

-- 
Robert Lemmen                               http://www.semistable.com 

Re: hda-intel without headphone output

[Tobin Davis]

Oops.  The patch I sent you was based on a previous HG snapshot.  I
updated my tree and remade the patch.  It just went out to the mailing
list & Takashi for integration in the main tree.

Tobin

On Thu, 2007-06-21 at 19:12 +0200, Robert Lemmen wrote:

> On Thu, Jun 21, 2007 at 12:24:23PM +0200, Takashi Iwai wrote:
> > > i am sorry, but this still doesn't work.
> > 
> > Are you sure that you remove model option with that patch?
> > The model option overrides the default model preset.
> 
> sorry for the confusion, but the second patch i got here (the one where
> the model is set to "laptop" in the quirks stuff), actually *does* work
> fine. it seems it was a bit late for me, and i got confused with
> different versions of the modules under /lib/**.
> 
> cu  robert
> 

-- 
Tobin Davis <tdavis@dsl-only.net>

Re: hda-intel without headphone output

[Takashi Iwai]

At Thu, 21 Jun 2007 19:12:30 +0200,
Robert Lemmen wrote:
> 
> On Thu, Jun 21, 2007 at 12:24:23PM +0200, Takashi Iwai wrote:
> > > i am sorry, but this still doesn't work.
> > 
> > Are you sure that you remove model option with that patch?
> > The model option overrides the default model preset.
> 
> sorry for the confusion, but the second patch i got here (the one where
> the model is set to "laptop" in the quirks stuff), actually *does* work
> fine. it seems it was a bit late for me, and i got confused with
> different versions of the modules under /lib/**.

Do you mean the patch below (posted by Tobin)?
If this really works for you, I'll merge it happily.


Takashi


diff -r deaa182aebd8 pci/hda/patch_conexant.c
--- a/pci/hda/patch_conexant.c	Wed Jun 20 15:46:13 2007 +0200
+++ b/pci/hda/patch_conexant.c	Thu Jun 21 10:48:49 2007 -0700
@@ -802,7 +802,7 @@ static struct snd_pci_quirk cxt5045_cfg_
 	SND_PCI_QUIRK(0x103c, 0x30b5, "HP DV2120", CXT5045_LAPTOP),
 	SND_PCI_QUIRK(0x103c, 0x30cd, "HP DV Series", CXT5045_LAPTOP),
 	SND_PCI_QUIRK(0x1734, 0x10ad, "Fujitsu Si1520", CXT5045_FUJITSU),
-	SND_PCI_QUIRK(0x1734, 0x10cb, "Fujitsu Si3515", CXT5045_FUJITSU),
+	SND_PCI_QUIRK(0x1734, 0x10cb, "Fujitsu Si3515", CXT5045_LAPTOP),
 	SND_PCI_QUIRK(0x8086, 0x2111, "Conexant Reference board", CXT5045_LAPTOP),
 	{}
 };

Re: hda-intel without headphone output

[Robert Lemmen]

hi takashi,

On Fri, Jun 22, 2007 at 03:27:13PM +0200, Takashi Iwai wrote:
> Do you mean the patch below (posted by Tobin)?
> If this really works for you, I'll merge it happily.
> [...]
> diff -r deaa182aebd8 pci/hda/patch_conexant.c
> --- a/pci/hda/patch_conexant.c	Wed Jun 20 15:46:13 2007 +0200
> +++ b/pci/hda/patch_conexant.c	Thu Jun 21 10:48:49 2007 -0700
> @@ -802,7 +802,7 @@ static struct snd_pci_quirk cxt5045_cfg_
>  	SND_PCI_QUIRK(0x103c, 0x30b5, "HP DV2120", CXT5045_LAPTOP),
>  	SND_PCI_QUIRK(0x103c, 0x30cd, "HP DV Series", CXT5045_LAPTOP),
>  	SND_PCI_QUIRK(0x1734, 0x10ad, "Fujitsu Si1520", CXT5045_FUJITSU),
> -	SND_PCI_QUIRK(0x1734, 0x10cb, "Fujitsu Si3515", CXT5045_FUJITSU),
> +	SND_PCI_QUIRK(0x1734, 0x10cb, "Fujitsu Si3515", CXT5045_LAPTOP),
>  	SND_PCI_QUIRK(0x8086, 0x2111, "Conexant Reference board", CXT5045_LAPTOP),
>  	{}
>  };

exactly, this works perfectly on my machine!

cu  robert

-- 
Robert Lemmen                               http://www.semistable.com 

Re: hda-intel without headphone output

[Takashi Iwai]

At Mon, 25 Jun 2007 10:07:44 +0200,
Robert Lemmen wrote:
> 
> hi takashi,
> 
> On Fri, Jun 22, 2007 at 03:27:13PM +0200, Takashi Iwai wrote:
> > Do you mean the patch below (posted by Tobin)?
> > If this really works for you, I'll merge it happily.
> > [...]
> > diff -r deaa182aebd8 pci/hda/patch_conexant.c
> > --- a/pci/hda/patch_conexant.c	Wed Jun 20 15:46:13 2007 +0200
> > +++ b/pci/hda/patch_conexant.c	Thu Jun 21 10:48:49 2007 -0700
> > @@ -802,7 +802,7 @@ static struct snd_pci_quirk cxt5045_cfg_
> >  	SND_PCI_QUIRK(0x103c, 0x30b5, "HP DV2120", CXT5045_LAPTOP),
> >  	SND_PCI_QUIRK(0x103c, 0x30cd, "HP DV Series", CXT5045_LAPTOP),
> >  	SND_PCI_QUIRK(0x1734, 0x10ad, "Fujitsu Si1520", CXT5045_FUJITSU),
> > -	SND_PCI_QUIRK(0x1734, 0x10cb, "Fujitsu Si3515", CXT5045_FUJITSU),
> > +	SND_PCI_QUIRK(0x1734, 0x10cb, "Fujitsu Si3515", CXT5045_LAPTOP),
> >  	SND_PCI_QUIRK(0x8086, 0x2111, "Conexant Reference board", CXT5045_LAPTOP),
> >  	{}
> >  };
> 
> exactly, this works perfectly on my machine!

Thanks for confirmation.  Now committed to HG tree.


Takashi