From: Andrew Morton <akpm@linux-foundation.org>
To: Christian Volkmann <haveaniceday@cv-sv.de>
Cc: linux-kernel@vger.kernel.org,
Michal Piotrowski <michal.k.k.piotrowski@gmail.com>,
linux-usb-devel@lists.sourceforge.net
Subject: Re: 2.6.23-rc6: usb 1-1: device not accepting address 2, error -62
Date: Sat, 15 Sep 2007 03:48:19 -0700 [thread overview]
Message-ID: <20070915034819.3e695370.akpm@linux-foundation.org> (raw)
In-Reply-To: <46EAFCF7.1030907@cv-sv.de>
Let's cc the USB mailing list.
On Fri, 14 Sep 2007 23:28:23 +0200 Christian Volkmann <haveaniceday@cv-sv.de> wrote:
> Hi everybody,
>
> I have an error message with 2.6.23-rc6.
> This did not happen with 2.6.22.
Another one for Michal's dirt file.
> The kernel reports message like this:
> <3>usb 1-1: device not accepting address 2, error -62
> <3>hub 2-2.1:1.0: hub_port_status failed (err = -71)
>
> Does this message harm or is something broken in 2.6.23-rc6 ?
> I get this kind of messages also with 2.6.23-rc3
Does the machine otherwise work OK?
Even if it does, I don't think we should be (newly) spraying scary messages
like that at people.
> Best regards,
>
> Christian
>
>
> Please see below for:
>
> grep -e hub -e usb boot.msg for a 2.6.23-rc6 boot. (that boot was without (err = -71)
> grep -e hub -e usb boot.msg for a 2.6.22 boot.
> lspci -vnn (2.6.22)
> lsusb -v (2.6.22)
>
>
> 2.6.23-rc6 boot.msg extract ( hub/usb )
>
> <6>usbcore: registered new interface driver usbfs
> <6>usbcore: registered new interface driver hub
> <6>usbcore: registered new device driver usb
> <6>usb usb1: configuration #1 chosen from 1 choice
> <6>hub 1-0:1.0: USB hub found
> <6>hub 1-0:1.0: 2 ports detected
> <6>usb usb2: configuration #1 chosen from 1 choice
> <6>hub 2-0:1.0: USB hub found
> <6>hub 2-0:1.0: 2 ports detected
> <6>usb 1-1: new low speed USB device using ohci_hcd and address 2
> <6>usb usb3: configuration #1 chosen from 1 choice
> <6>hub 3-0:1.0: USB hub found
> <6>hub 3-0:1.0: 2 ports detected
> <6>usb usb4: configuration #1 chosen from 1 choice
> <6>hub 4-0:1.0: USB hub found
> <6>hub 4-0:1.0: 6 ports detected
> <6>usb usb5: configuration #1 chosen from 1 choice
> <6>hub 5-0:1.0: USB hub found
> <6>hub 5-0:1.0: 2 ports detected
> <3>usb 1-1: device not accepting address 2, error -62
> <6>usb 5-2: new full speed USB device using uhci_hcd and address 2
> <6>usb usb6: configuration #1 chosen from 1 choice
> <6>hub 6-0:1.0: USB hub found
> <6>hub 6-0:1.0: 4 ports detected
> <6>usb usb7: configuration #1 chosen from 1 choice
> <6>hub 7-0:1.0: USB hub found
> <6>hub 7-0:1.0: 2 ports detected
> <6>usb 1-1: new low speed USB device using ohci_hcd and address 4
> <6>usb 1-1: configuration #1 chosen from 1 choice
> <6>usb 2-1: new full speed USB device using ohci_hcd and address 2
> <6>usb 2-1: configuration #1 chosen from 1 choice
> <6>usb 6-2: new high speed USB device using ehci_hcd and address 2
> <6>usb 6-2: configuration #1 chosen from 1 choice
> <6>hub 6-2:1.0: USB hub found
> <6>hub 6-2:1.0: 2 ports detected
> <6>usbcore: registered new interface driver hiddev
> <6>input: USB HID v1.11 Mouse [USB Optical Mouse] on usb-0000:00:03.0-1
> <6>usbcore: registered new interface driver usbhid
> <6>drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
> <7>usb-storage: device found at 2
> <7>usb-storage: waiting for device to settle before scanning
> <6>usb 6-2.1: new high speed USB device using ehci_hcd and address 3
> <6>usb 6-2.1: configuration #1 chosen from 1 choice
> <6>hub 6-2.1:1.0: USB hub found
> <6>hub 6-2.1:1.0: 4 ports detected
> <6>usb 6-2.1.1: new high speed USB device using ehci_hcd and address 4
> <6>usb 6-2.1.1: configuration #1 chosen from 1 choice
> <7>usb-storage: device found at 4
> <7>usb-storage: waiting for device to settle before scanning
> <6>usbcore: registered new interface driver usb-storage
> <7>usb-storage: device scan complete
> <7>usb-storage: device scan complete
>
> 2.6.22 boot.msg extract ( hub/usb )
>
> <6>usbcore: registered new interface driver usbfs
> <6>usbcore: registered new interface driver hub
> <6>usbcore: registered new device driver usb
> <6>usb usb1: configuration #1 chosen from 1 choice
> <6>hub 1-0:1.0: USB hub found
> <6>hub 1-0:1.0: 2 ports detected
> <6>usb usb2: configuration #1 chosen from 1 choice
> <6>hub 2-0:1.0: USB hub found
> <6>hub 2-0:1.0: 2 ports detected
> <6>usb 1-1: new low speed USB device using ohci_hcd and address 2
> <6>usb usb3: configuration #1 chosen from 1 choice
> <6>hub 3-0:1.0: USB hub found
> <6>hub 3-0:1.0: 2 ports detected
> <6>usb 1-1: configuration #1 chosen from 1 choice
> <6>usb usb4: configuration #1 chosen from 1 choice
> <6>hub 4-0:1.0: USB hub found
> <6>hub 4-0:1.0: 6 ports detected
> <6>usb 1-1: USB disconnect, address 2
> <6>usb usb5: configuration #1 chosen from 1 choice
> <6>hub 5-0:1.0: USB hub found
> <6>hub 5-0:1.0: 4 ports detected
> <6>usb usb6: configuration #1 chosen from 1 choice
> <6>hub 6-0:1.0: USB hub found
> <6>hub 6-0:1.0: 2 ports detected
> <6>usb usb7: configuration #1 chosen from 1 choice
> <6>hub 7-0:1.0: USB hub found
> <6>hub 7-0:1.0: 2 ports detected
> <6>usb 5-2: new high speed USB device using ehci_hcd and address 2
> <6>usb 5-2: configuration #1 chosen from 1 choice
> <6>hub 5-2:1.0: USB hub found
> <6>hub 5-2:1.0: 2 ports detected
> <6>usb 1-1: new low speed USB device using ohci_hcd and address 3
> <6>usb 1-1: configuration #1 chosen from 1 choice
> <6>usbcore: registered new interface driver hiddev
> <6>usb 2-1: new full speed USB device using ohci_hcd and address 2
> <6>usb 2-1: configuration #1 chosen from 1 choice
> <6>usb 5-2.1: new high speed USB device using ehci_hcd and address 3
> <6>usb 5-2.1: configuration #1 chosen from 1 choice
> <6>hub 5-2.1:1.0: USB hub found
> <6>hub 5-2.1:1.0: 4 ports detected
> <6>input: USB HID v1.11 Mouse [USB Optical Mouse] on usb-0000:00:03.0-1
> <7>usb-storage: device found at 2
> <7>usb-storage: waiting for device to settle before scanning
> <6>usb 5-2.1.1: new high speed USB device using ehci_hcd and address 4
> <6>usb 5-2.1.1: configuration #1 chosen from 1 choice
> <6>usbcore: registered new interface driver usbhid
> <7>usb-storage: device found at 4
> <7>usb-storage: waiting for device to settle before scanning
> <6>usbcore: registered new interface driver usb-storage
> <6>drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
> <7>usb-storage: device scan complete
> <7>usb-storage: device scan complete
>
> [system info snipped ]
>
next prev parent reply other threads:[~2007-09-15 10:48 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
2007-09-14 21:28 2.6.23-rc6: usb 1-1: device not accepting address 2, error -62 Christian Volkmann
2007-09-15 10:48 ` Andrew Morton [this message]
2007-09-15 11:50 ` Christian Volkmann
2007-09-15 12:06 ` Christian Volkmann
2007-09-15 15:31 ` [linux-usb-devel] " Alan Stern
2007-09-15 17:07 ` Christian Volkmann
2007-09-15 19:55 ` Alan Stern
2007-09-15 16:56 ` Pete Zaitcev
2007-09-15 17:11 ` Christian Volkmann
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20070915034819.3e695370.akpm@linux-foundation.org \
--to=akpm@linux-foundation.org \
--cc=haveaniceday@cv-sv.de \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-usb-devel@lists.sourceforge.net \
--cc=michal.k.k.piotrowski@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.