From: Christian Volkmann <haveaniceday@cv-sv.de>
To: unlisted-recipients:; (no To-header on input)
Cc: Alan Stern <stern@rowland.harvard.edu>,
Andrew Morton <akpm@linux-foundation.org>,
linux-kernel@vger.kernel.org,
linux-usb-devel@lists.sourceforge.net,
Michal Piotrowski <michal.k.k.piotrowski@gmail.com>,
haveaniceday@cv-sv.de
Subject: Re: [linux-usb-devel] 2.6.23-rc6: usb 1-1: device not accepting address 2, error -62
Date: Sat, 15 Sep 2007 19:07:06 +0200 [thread overview]
Message-ID: <46EC113A.4040309@cv-sv.de> (raw)
In-Reply-To: <Pine.LNX.4.44L0.0709151123590.30525-100000@netrider.rowland.org>
Please see below for the logs with timestamp and usb-debug.
Alan Stern wrote:
> On Sat, 15 Sep 2007, Christian Volkmann wrote:
>
>>> Does the machine otherwise work OK?
>>>
>> Yes, the USB is working fine for the easy things I do with it.
>>
>> Hmm, so I expect this 2.6.22 message:
>>>> <6>usb 1-1: USB disconnect, address 2
>> became this 2.6.23rc6 message:
>>>> <3>usb 1-1: device not accepting address 2, error -62
>> and nothing is harmed.
>
> Maybe. It's hard to tell because you have not provided enough
> information. To get a better idea of what's going on you should enable
> CONFIG_USB_DEBUG, for both 2.6.22 and 2.6.23, and then post the dmesg
> logs. It wouldn't hurt to enable CONFIG_PRINTK_TIME also.
>
> These sorts of errors can occur because of bad cable connections or
> other similar hardware problems. There's an excellent chance they have
> no connection to the kernel version.
>
> Alan Stern
>
>
Boot of 2.6.22 with CONFIG_PRINTK_TIME and CONFIG_USB_DEBUG
klogd 1.4.1, log source = ksyslog started.
<5>[ 0.000000] Linux version 2.6.22-speedy (root@speedy) (gcc version 4.1.2 20061115 (prerelease) (SUSE Linux)) #3 PREEMPT Sat Sep 15 18:43:47 CEST 2007
<6>[ 0.000000] BIOS-provided physical RAM map:
<4>[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
<4>[ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
<4>[ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
<4>[ 0.000000] BIOS-e820: 0000000000100000 - 000000005fff0000 (usable)
<4>[ 0.000000] BIOS-e820: 000000005fff0000 - 000000005fff3000 (ACPI NVS)
<4>[ 0.000000] BIOS-e820: 000000005fff3000 - 0000000060000000 (ACPI data)
<5>[ 0.000000] 639MB HIGHMEM available.
<5>[ 0.000000] 896MB LOWMEM available.
<6>[ 0.000000] found SMP MP-table at 000f5980
<7>[ 0.000000] Entering add_active_range(0, 0, 393200) 0 entries of 256 used
<4>[ 0.000000] Zone PFN ranges:
<4>[ 0.000000] DMA 0 -> 4096
<4>[ 0.000000] Normal 4096 -> 229376
<4>[ 0.000000] HighMem 229376 -> 393200
<4>[ 0.000000] early_node_map[1] active PFN ranges
<4>[ 0.000000] 0: 0 -> 393200
<7>[ 0.000000] On node 0 totalpages: 393200
<7>[ 0.000000] DMA zone: 32 pages used for memmap
<7>[ 0.000000] DMA zone: 0 pages reserved
<7>[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
<7>[ 0.000000] Normal zone: 1760 pages used for memmap
<7>[ 0.000000] Normal zone: 223520 pages, LIFO batch:31
<7>[ 0.000000] HighMem zone: 1279 pages used for memmap
<7>[ 0.000000] HighMem zone: 162545 pages, LIFO batch:31
<6>[ 0.000000] DMI 2.3 present.
<4>[ 0.000000] ACPI: RSDP 000F7350, 0014 (r0 AWARD )
<4>[ 0.000000] ACPI: RSDT 5FFF3000, 002C (r1 AWARD AWRDACPI 42302E31 AWRD 0)
<4>[ 0.000000] ACPI: FACP 5FFF3040, 0074 (r1 AWARD AWRDACPI 42302E31 AWRD 0)
<4>[ 0.000000] ACPI: DSDT 5FFF30C0, 38BB (r1 AWARD AWRDACPI 1000 MSFT 100000D)
<4>[ 0.000000] ACPI: FACS 5FFF0000, 0040
<4>[ 0.000000] ACPI: APIC 5FFF6980, 0054 (r1 AWARD AWRDACPI 42302E31 AWRD 0)
<6>[ 0.000000] ACPI: PM-Timer IO Port: 0x1008
<7>[ 0.000000] ACPI: Local APIC address 0xfee00000
<6>[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
<4>[ 0.000000] Processor #0 15:2 APIC version 20
<6>[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
<4>[ 0.000000] IOAPIC[0]: apic_id 2, version 20, address 0xfec00000, GSI 0-23
<6>[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
<6>[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 dfl dfl)
<7>[ 0.000000] ACPI: IRQ0 used by override.
<7>[ 0.000000] ACPI: IRQ2 used by override.
<7>[ 0.000000] ACPI: IRQ9 used by override.
<4>[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
<6>[ 0.000000] Using ACPI (MADT) for SMP configuration information
<4>[ 0.000000] Allocating PCI resources starting at 70000000 (gap: 60000000:a0000000)
<4>[ 0.000000] Built 1 zonelists. Total pages: 390129
<5>[ 0.000000] Kernel command line: root=/dev/hdb7 vga=0x346 resume=/dev/hdb11 splash=verbose console=tty0 crashkernel=64M@16M 3
<7>[ 0.000000] mapped APIC to ffffd000 (fee00000)
<7>[ 0.000000] mapped IOAPIC to ffffc000 (fec00000)
<6>[ 0.000000] Enabling fast FPU save and restore... done.
<6>[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
<6>[ 0.000000] Initializing CPU#0
<4>[ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
<4>[ 0.000000] Detected 2672.804 MHz processor.
<4>[ 18.872274] Console: colour dummy device 80x25
<4>[ 18.873050] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
<4>[ 18.873822] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
<6>[ 18.922125] Memory: 1490032k/1572800k available (1742k kernel code, 81424k reserved, 662k data, 196k init, 655296k highmem)
<4>[ 18.922147] virtual kernel memory layout:
<4>[ 18.922148] fixmap : 0xfffaa000 - 0xfffff000 ( 340 kB)
<4>[ 18.922149] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
<4>[ 18.922151] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
<4>[ 18.922152] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
<4>[ 18.922153] .init : 0xc125c000 - 0xc128d000 ( 196 kB)
<4>[ 18.922155] .data : 0xc11b38f3 - 0xc1259484 ( 662 kB)
<4>[ 18.922156] .text : 0xc1000000 - 0xc11b38f3 (1742 kB)
<4>[ 18.922169] Checking if this processor honours the WP bit even in supervisor mode... Ok.
<4>[ 19.002291] Calibrating delay using timer specific routine.. 5349.25 BogoMIPS (lpj=10698513)
<6>[ 19.002337] Security Framework v1.0.0 initialized
<4>[ 19.002358] Mount-cache hash table entries: 512
<7>[ 19.002502] CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 00000400 00000000 00000000
<6>[ 19.002514] CPU: Trace cache: 12K uops, L1 D cache: 8K
<6>[ 19.002519] CPU: L2 cache: 512K
<7>[ 19.002523] CPU: After all inits, caps: bfebfbff 00000000 00000000 0000b080 00000400 00000000 00000000
<6>[ 19.002530] Intel machine check architecture supported.
<6>[ 19.002536] Intel machine check reporting enabled on CPU#0.
<6>[ 19.002540] CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
<6>[ 19.002545] CPU0: Thermal monitoring enabled
<4>[ 19.002554] Compat vDSO mapped to ffffe000.
<4>[ 19.002568] CPU: Intel(R) Pentium(R) 4 CPU 2.66GHz stepping 07
<6>[ 19.002577] Checking 'hlt' instruction... OK.
<6>[ 19.018378] ACPI: Core revision 20070126
<4>[ 19.127629] ENABLING IO-APIC IRQs
<6>[ 19.127803] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
<6>[ 19.274383] NET: Registered protocol family 16
<6>[ 19.274494] ACPI: bus type pci registered
<6>[ 19.313809] PCI: PCI BIOS revision 2.10 entry at 0xfb400, last bus=1
<6>[ 19.313813] PCI: Using configuration type 1
<4>[ 19.313816] Setting up standard PCI resources
<6>[ 19.324546] ACPI: Interpreter enabled
<6>[ 19.324556] ACPI: (supports S0 S3 S4 S5)
<6>[ 19.324578] ACPI: Using IOAPIC for interrupt routing
<6>[ 19.329173] ACPI: PCI Root Bridge [PCI0] (0000:00)
<7>[ 19.329191] PCI: Probing PCI hardware (bus 00)
<6>[ 19.329479] Enabling SiS 96x SMBus.
<7>[ 19.331073] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
<4>[ 19.352987] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
<4>[ 19.353097] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
<4>[ 19.353208] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 *7 9 10 11 12 14 15)
<4>[ 19.353316] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
<4>[ 19.353420] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
<4>[ 19.353525] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
<4>[ 19.353631] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
<4>[ 19.353734] ACPI: PCI Interrupt Link [LNKH] (IRQs *3 4 5 6 7 9 10 11 12 14 15)
<6>[ 19.353835] Linux Plug and Play Support v0.97 (c) Adam Belay
<6>[ 19.353852] pnp: PnP ACPI init
<6>[ 19.353862] ACPI: bus type pnp registered
<6>[ 19.355941] pnp: PnP ACPI: found 11 devices
<6>[ 19.355947] ACPI: ACPI bus type pnp unregistered
<6>[ 19.355954] PnPBIOS: Disabled by ACPI PNP
<6>[ 19.356032] PCI: Using ACPI for IRQ routing
<6>[ 19.356037] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
<6>[ 19.372489] pnp: 00:00: iomem range 0xd0000-0xd3fff has been reserved
<6>[ 19.372495] pnp: 00:00: iomem range 0xf0000-0xf7fff could not be reserved
<6>[ 19.372499] pnp: 00:00: iomem range 0xf8000-0xfbfff could not be reserved
<6>[ 19.372503] pnp: 00:00: iomem range 0xfc000-0xfffff could not be reserved
<6>[ 19.374201] Time: tsc clocksource has been installed.
<6>[ 19.402836] PCI: Bridge: 0000:00:01.0
<6>[ 19.402840] IO window: disabled.
<6>[ 19.402850] MEM window: e0000000-e1ffffff
<6>[ 19.402857] PREFETCH window: d8000000-dfffffff
<6>[ 19.402901] NET: Registered protocol family 2
<4>[ 19.442210] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
<4>[ 19.442382] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
<4>[ 19.443552] TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
<6>[ 19.443951] TCP: Hash tables configured (established 131072 bind 65536)
<6>[ 19.443956] TCP reno registered
<6>[ 19.454365] checking if image is initramfs... it is
<6>[ 19.685765] Freeing initrd memory: 2802k freed
<6>[ 19.685969] Machine check exception polling timer started.
<6>[ 19.686000] apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
<5>[ 19.686004] apm: overridden by ACPI.
<6>[ 19.686257] audit: initializing netlink socket (disabled)
<5>[ 19.686277] audit(1189882148.244:1): initialized
<4>[ 19.686356] highmem bounce pool size: 64 pages
<4>[ 19.686362] Total HugeTLB memory allocated, 0
<5>[ 19.686423] VFS: Disk quotas dquot_6.5.1
<4>[ 19.686436] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
<6>[ 19.686513] io scheduler noop registered
<6>[ 19.686517] io scheduler anticipatory registered
<6>[ 19.686520] io scheduler deadline registered
<6>[ 19.686533] io scheduler cfq registered (default)
<7>[ 19.770100] pci 0000:00:07.0: uhci_check_and_reset_hc: legsup = 0x2000
<7>[ 19.770102] pci 0000:00:07.0: Performing full reset
<7>[ 19.770120] pci 0000:00:07.1: uhci_check_and_reset_hc: legsup = 0x2000
<7>[ 19.770122] pci 0000:00:07.1: Performing full reset
<7>[ 19.770150] Boot video device is 0000:01:00.0
<6>[ 19.770391] vesafb: framebuffer at 0xd8000000, mapped to 0xf8880000, using 7500k, total 131072k
<6>[ 19.770398] vesafb: mode is 1600x1200x16, linelength=3200, pages=1
<6>[ 19.770402] vesafb: protected mode interface info at c000:def0
<6>[ 19.770406] vesafb: pmi: set display start = c00cdf35, set palette = c00cdfba
<6>[ 19.770409] vesafb: pmi: ports = b4c3 b503 ba03 c003 c103 c403 c503 c603 c703 c803 c903 cc03 ce03 cf03 d003 d103 d203 d303 d403 d503 da03 ff03
<6>[ 19.770432] vesafb: scrolling: redraw
<6>[ 19.770436] vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
<4>[ 19.836587] Console: switching to colour frame buffer device 200x75
<6>[ 19.902936] fb0: VESA VGA frame buffer device
<6>[ 19.903209] isapnp: Scanning for PnP cards...
<6>[ 19.930043] Switched to NOHz mode on CPU #0
<6>[ 20.213994] isapnp: No Plug & Play device found
<6>[ 20.220984] Real Time Clock Driver v1.12ac
<6>[ 20.221309] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
<6>[ 20.222217] 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
<6>[ 20.222695] Floppy drive(s): fd0 is 1.44M
<6>[ 20.241646] FDC 0 is a post-1991 82077
<4>[ 20.243357] RAMDISK driver initialized: 16 RAM disks of 64000K size 1024 blocksize
<6>[ 20.243912] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
<6>[ 20.244563] serio: i8042 KBD port at 0x60,0x64 irq 1
<6>[ 20.244824] serio: i8042 AUX port at 0x60,0x64 irq 12
<6>[ 20.245210] mice: PS/2 mouse device common for all mice
<6>[ 20.278974] input: AT Translated Set 2 keyboard as /class/input/input0
<6>[ 20.289144] input: PC Speaker as /class/input/input1
<6>[ 20.930810] input: ImPS/2 Generic Wheel Mouse as /class/input/input2
<6>[ 20.935659] NET: Registered protocol family 1
<4>[ 20.935886] Using IPI Shortcut mode
<6>[ 20.936533] Freeing unused kernel memory: 196k freed
<6>[ 21.227423] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
<6>[ 21.227764] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
<6>[ 21.245864] ACPI: Thermal Zone [THRM] (47 C)
<6>[ 21.250555] SIS5513: IDE controller at PCI slot 0000:00:02.5
<6>[ 21.250889] ACPI: PCI Interrupt 0000:00:02.5[A] -> GSI 16 (level, low) -> IRQ 16
<6>[ 21.251289] SIS5513: chipset revision 0
<6>[ 21.251486] SIS5513: not 100% native mode: will probe irqs later
<6>[ 21.251809] SIS5513: SiS 962/963 MuTIOL IDE UDMA133 controller
<6>[ 21.252128] ide0: BM-DMA at 0x4000-0x4007, BIOS settings: hda:DMA, hdb:DMA
<6>[ 21.252530] ide1: BM-DMA at 0x4008-0x400f, BIOS settings: hdc:DMA, hdd:DMA
<7>[ 21.252926] Probing IDE interface ide0...
<4>[ 21.541611] hda: ST3120023A, ATA DISK drive
<4>[ 21.821506] hdb: SAMSUNG SP2514N, ATA DISK drive
<7>[ 21.877534] hda: selected mode 0x45
<7>[ 21.894893] hdb: selected mode 0x45
<4>[ 21.911444] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
<6>[ 21.920761] hda: max request size: 128KiB
<6>[ 21.921180] hda: 234441648 sectors (120034 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(100)
<6>[ 21.921781] hda: cache flushes supported
<6>[ 21.922023] hda: hda1 hda2 < hda5 hda6 hda7 hda8 hda9 hda10 hda11 >
<6>[ 21.994408] hdb: max request size: 512KiB
<6>[ 21.994750] hdb: 488397168 sectors (250059 MB) w/8192KiB Cache, CHS=30401/255/63, UDMA(100)
<6>[ 22.008117] hdb: cache flushes supported
<6>[ 22.008376] hdb: hdb1 hdb2 < hdb5 hdb6 hdb7 hdb8 hdb9 hdb10 hdb11 hdb12 >
<7>[ 22.156505] Probing IDE interface ide1...
<4>[ 22.893122] hdc: IDE DVD-ROM 16X, ATAPI CD/DVD-ROM drive
<4>[ 23.692825] hdd: _NEC DVD_RW ND-1300A, ATAPI CD/DVD-ROM drive
<7>[ 23.765512] hdc: selected mode 0x42
<7>[ 23.766684] hdd: selected mode 0x42
<4>[ 23.766850] ide1 at 0x170-0x177,0x376 on irq 15
<6>[ 23.796256] ACPI: Fan [FAN] (on)
<6>[ 23.817791] BIOS EDD facility v0.16 2004-Jun-25, 2 devices found
<4>[ 24.071685] swsusp: Basic memory bitmaps created
<4>[ 24.113309] swsusp: Basic memory bitmaps freed
<4>[ 24.145965] Attempting manual resume
<6>[ 24.317018] kjournald starting. Commit interval 5 seconds
<6>[ 24.333326] EXT3 FS on hdb7, internal journal
<6>[ 24.349502] EXT3-fs: mounted filesystem with ordered data mode.
<6>[ 27.119629] lp: driver loaded but no devices found
<6>[ 28.527222] Linux agpgart interface v0.102 (c) Dave Jones
<6>[ 28.689557] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
<6>[ 28.736517] sis96x_smbus 0000:00:02.1: SiS96x SMBus base address: 0x10c0
<6>[ 28.773762] hdc: ATAPI 16X DVD-ROM drive, 512kB Cache, UDMA(33)
<6>[ 28.790484] Uniform CD-ROM driver Revision: 3.20
<6>[ 28.808164] agpgart: Detected SiS chipset - id:1608
<6>[ 28.832562] agpgart: AGP aperture is 128M @ 0xd0000000
<6>[ 28.856063] hdd: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
<6>[ 28.878911] usbcore: registered new interface driver usbfs
<6>[ 28.895484] usbcore: registered new interface driver hub
<6>[ 28.911912] usbcore: registered new device driver usb
<6>[ 28.948719] ACPI: PCI Interrupt 0000:00:02.3[B] -> GSI 17 (level, low) -> IRQ 17
<6>[ 29.016935] ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[17] MMIO=[e2020000-e20207ff] Max Packet=[2048] IR/IT contexts=[4/6]
<7>[ 29.035665] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
<7>[ 29.035669] ohci_hcd: block sizes: ed 64 td 64
<6>[ 29.045019] ACPI: PCI Interrupt 0000:00:03.0[A] -> GSI 20 (level, low) -> IRQ 18
<6>[ 29.061902] ohci_hcd 0000:00:03.0: OHCI Host Controller
<6>[ 29.078652] ohci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 1
<7>[ 29.095312] ohci_hcd 0000:00:03.0: created debug files
<6>[ 29.095323] ohci_hcd 0000:00:03.0: irq 18, io mem 0xe2021000
<7>[ 29.113398] ehci_hcd: block sizes: qh 128 qtd 96 itd 192 sitd 96
<6>[ 29.114643] USB Universal Host Controller Interface driver v3.0
<7>[ 29.169233] ohci_hcd 0000:00:03.0: OHCI controller state
<7>[ 29.169240] ohci_hcd 0000:00:03.0: OHCI 1.0, NO legacy support registers
<7>[ 29.169244] ohci_hcd 0000:00:03.0: control 0x083 HCFS=operational CBSR=3
<7>[ 29.169248] ohci_hcd 0000:00:03.0: cmdstatus 0x00000 SOC=0
<7>[ 29.169251] ohci_hcd 0000:00:03.0: intrstatus 0x00000044 RHSC SF
<7>[ 29.169255] ohci_hcd 0000:00:03.0: intrenable 0x8000000a MIE RD WDH
<7>[ 29.169261] ohci_hcd 0000:00:03.0: hcca frame #0003
<7>[ 29.169266] ohci_hcd 0000:00:03.0: roothub.a 01001202 POTPGT=1 NOCP NPS NDP=2(2)
<7>[ 29.169270] ohci_hcd 0000:00:03.0: roothub.b 00000000 PPCM=0000 DR=0000
<7>[ 29.169274] ohci_hcd 0000:00:03.0: roothub.status 00008000 DRWE
<7>[ 29.169279] ohci_hcd 0000:00:03.0: roothub.portstatus [0] 0x00010301 CSC LSDA PPS CCS
<7>[ 29.169283] ohci_hcd 0000:00:03.0: roothub.portstatus [1] 0x00000100 PPS
<7>[ 29.169307] usb usb1: default language 0x0409
<7>[ 29.169315] usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
<6>[ 29.169318] usb usb1: Product: OHCI Host Controller
<6>[ 29.185890] usb usb1: Manufacturer: Linux 2.6.22-speedy ohci_hcd
<6>[ 29.202783] usb usb1: SerialNumber: 0000:00:03.0
<7>[ 29.219533] usb usb1: uevent
<7>[ 29.219553] usb usb1: usb_probe_device
<6>[ 29.219618] usb usb1: configuration #1 chosen from 1 choice
<7>[ 29.236354] usb usb1: adding 1-0:1.0 (config #1, interface 0)
<7>[ 29.236366] usb 1-0:1.0: uevent
<7>[ 29.236370] usb 1-0:1.0: uevent
<7>[ 29.236382] hub 1-0:1.0: usb_probe_interface
<7>[ 29.236384] hub 1-0:1.0: usb_probe_interface - got id
<6>[ 29.236387] hub 1-0:1.0: USB hub found
<6>[ 29.253193] hub 1-0:1.0: 2 ports detected
<7>[ 29.270135] hub 1-0:1.0: standalone hub
<7>[ 29.270138] hub 1-0:1.0: no power switching (usb 1.0)
<7>[ 29.270140] hub 1-0:1.0: no over-current protection
<7>[ 29.270143] hub 1-0:1.0: power on to power good time: 2ms
<7>[ 29.270149] hub 1-0:1.0: local power source is good
<7>[ 29.270153] hub 1-0:1.0: trying to enable port power on non-switchable hub
<6>[ 29.344199] sis900.c: v1.08.10 Apr. 2 2006
<7>[ 29.371190] hub 1-0:1.0: state 7 ports 2 chg 0000 evt 0000
<7>[ 29.371289] ohci_hcd 0000:00:03.0: GetStatus roothub.portstatus [0] = 0x00010301 CSC LSDA PPS CCS
<7>[ 29.371297] hub 1-0:1.0: port 1, status 0301, change 0001, 1.5 Mb/s
<6>[ 29.371333] ACPI: PCI Interrupt 0000:00:03.1[B] -> GSI 21 (level, low) -> IRQ 19
<6>[ 29.388672] ohci_hcd 0000:00:03.1: OHCI Host Controller
<6>[ 29.406003] ohci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 2
<7>[ 29.423513] ohci_hcd 0000:00:03.1: created debug files
<6>[ 29.423523] ohci_hcd 0000:00:03.1: irq 19, io mem 0xe2022000
<7>[ 29.497167] ohci_hcd 0000:00:03.1: OHCI controller state
<7>[ 29.497174] ohci_hcd 0000:00:03.1: OHCI 1.0, NO legacy support registers
<7>[ 29.497178] ohci_hcd 0000:00:03.1: control 0x083 HCFS=operational CBSR=3
<7>[ 29.497181] ohci_hcd 0000:00:03.1: cmdstatus 0x00000 SOC=0
<7>[ 29.497185] ohci_hcd 0000:00:03.1: intrstatus 0x00000044 RHSC SF
<7>[ 29.497189] ohci_hcd 0000:00:03.1: intrenable 0x8000000a MIE RD WDH
<7>[ 29.497195] ohci_hcd 0000:00:03.1: hcca frame #0003
<7>[ 29.497199] ohci_hcd 0000:00:03.1: roothub.a 01001202 POTPGT=1 NOCP NPS NDP=2(2)
<7>[ 29.497203] ohci_hcd 0000:00:03.1: roothub.b 00000000 PPCM=0000 DR=0000
<7>[ 29.497207] ohci_hcd 0000:00:03.1: roothub.status 00008000 DRWE
<7>[ 29.497212] ohci_hcd 0000:00:03.1: roothub.portstatus [0] 0x00010101 CSC PPS CCS
<7>[ 29.497217] ohci_hcd 0000:00:03.1: roothub.portstatus [1] 0x00000100 PPS
<7>[ 29.497238] usb usb2: default language 0x0409
<7>[ 29.497246] usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
<6>[ 29.497250] usb usb2: Product: OHCI Host Controller
<7>[ 29.514516] hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
<6>[ 29.514527] usb usb2: Manufacturer: Linux 2.6.22-speedy ohci_hcd
<6>[ 29.531733] usb usb2: SerialNumber: 0000:00:03.1
<7>[ 29.548846] usb usb2: uevent
<7>[ 29.548865] usb usb2: usb_probe_device
<6>[ 29.548911] usb usb2: configuration #1 chosen from 1 choice
<7>[ 29.565986] usb usb2: adding 2-0:1.0 (config #1, interface 0)
<7>[ 29.565998] usb 2-0:1.0: uevent
<7>[ 29.566001] usb 2-0:1.0: uevent
<7>[ 29.566012] hub 2-0:1.0: usb_probe_interface
<7>[ 29.566014] hub 2-0:1.0: usb_probe_interface - got id
<6>[ 29.566017] hub 2-0:1.0: USB hub found
<6>[ 29.582872] hub 2-0:1.0: 2 ports detected
<7>[ 29.599493] ohci_hcd 0000:00:03.0: GetStatus roothub.portstatus [0] = 0x00100303 PRSC LSDA PPS PES CCS
<7>[ 29.599498] hub 2-0:1.0: standalone hub
<7>[ 29.599500] hub 2-0:1.0: no power switching (usb 1.0)
<7>[ 29.599503] hub 2-0:1.0: no over-current protection
<7>[ 29.599506] hub 2-0:1.0: power on to power good time: 2ms
<7>[ 29.599511] hub 2-0:1.0: local power source is good
<7>[ 29.599515] hub 2-0:1.0: trying to enable port power on non-switchable hub
<6>[ 29.638785] Linux video capture interface: v2.00
<6>[ 29.655430] usb 1-1: new low speed USB device using ohci_hcd and address 2
<6>[ 29.703221] ACPI: PCI Interrupt 0000:00:03.2[C] -> GSI 22 (level, low) -> IRQ 20
<6>[ 29.720114] ohci_hcd 0000:00:03.2: OHCI Host Controller
<6>[ 29.736975] ohci_hcd 0000:00:03.2: new USB bus registered, assigned bus number 3
<7>[ 29.753911] ohci_hcd 0000:00:03.0: GetStatus roothub.portstatus [0] = 0x00100303 PRSC LSDA PPS PES CCS
<7>[ 29.753926] ohci_hcd 0000:00:03.2: created debug files
<6>[ 29.753936] ohci_hcd 0000:00:03.2: irq 20, io mem 0xe2023000
<6>[ 29.777186] saa7130/34: v4l2 driver version 0.2.14 loaded
<7>[ 29.827036] ohci_hcd 0000:00:03.2: enabling initreset quirk
<7>[ 29.829035] ohci_hcd 0000:00:03.2: OHCI controller state
<7>[ 29.829039] ohci_hcd 0000:00:03.2: OHCI 1.0, NO legacy support registers
<7>[ 29.829043] ohci_hcd 0000:00:03.2: control 0x083 HCFS=operational CBSR=3
<7>[ 29.829046] ohci_hcd 0000:00:03.2: cmdstatus 0x00000 SOC=0
<7>[ 29.829050] ohci_hcd 0000:00:03.2: intrstatus 0x00000004 SF
<7>[ 29.829054] ohci_hcd 0000:00:03.2: intrenable 0x8000004a MIE RHSC RD WDH
<7>[ 29.829060] ohci_hcd 0000:00:03.2: hcca frame #0003
<7>[ 29.829065] ohci_hcd 0000:00:03.2: roothub.a 01001202 POTPGT=1 NOCP NPS NDP=2(2)
<7>[ 29.829068] ohci_hcd 0000:00:03.2: roothub.b 00000000 PPCM=0000 DR=0000
<7>[ 29.829072] ohci_hcd 0000:00:03.2: roothub.status 00008000 DRWE
<7>[ 29.829076] ohci_hcd 0000:00:03.2: roothub.portstatus [0] 0x00000100 PPS
<7>[ 29.829080] ohci_hcd 0000:00:03.2: roothub.portstatus [1] 0x00000100 PPS
<7>[ 29.829095] usb usb3: default language 0x0409
<7>[ 29.829103] usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1
<6>[ 29.829106] usb usb3: Product: OHCI Host Controller
<6>[ 29.846075] usb usb3: Manufacturer: Linux 2.6.22-speedy ohci_hcd
<6>[ 29.863230] usb usb3: SerialNumber: 0000:00:03.2
<7>[ 29.880478] usb usb3: uevent
<7>[ 29.880499] usb usb3: usb_probe_device
<6>[ 29.880544] usb usb3: configuration #1 chosen from 1 choice
<7>[ 29.897969] usb 1-1: skipped 1 descriptor after interface
<7>[ 29.897979] usb usb3: adding 3-0:1.0 (config #1, interface 0)
<7>[ 29.897991] usb 3-0:1.0: uevent
<7>[ 29.897995] usb 3-0:1.0: uevent
<7>[ 29.898007] hub 3-0:1.0: usb_probe_interface
<7>[ 29.898009] hub 3-0:1.0: usb_probe_interface - got id
<6>[ 29.898012] hub 3-0:1.0: USB hub found
<6>[ 29.915524] hub 3-0:1.0: 2 ports detected
<7>[ 29.932956] usb 1-1: default language 0x0409
<7>[ 29.932961] hub 3-0:1.0: standalone hub
<7>[ 29.932963] hub 3-0:1.0: no power switching (usb 1.0)
<7>[ 29.932966] hub 3-0:1.0: no over-current protection
<7>[ 29.932969] hub 3-0:1.0: power on to power good time: 2ms
<7>[ 29.932974] hub 3-0:1.0: local power source is good
<7>[ 29.932977] hub 3-0:1.0: trying to enable port power on non-switchable hub
<7>[ 29.935868] usb 1-1: new device strings: Mfr=0, Product=2, SerialNumber=0
<6>[ 29.935872] usb 1-1: Product: USB Optical Mouse
<7>[ 29.953324] usb 1-1: uevent
<7>[ 29.953338] usb 1-1: usb_probe_device
<6>[ 29.953377] usb 1-1: configuration #1 chosen from 1 choice
<7>[ 29.972852] usb 1-1: adding 1-1:1.0 (config #1, interface 0)
<7>[ 29.972873] usb 1-1:1.0: uevent
<7>[ 29.972876] usb 1-1:1.0: uevent
<7>[ 29.972945] hub 1-0:1.0: state 7 ports 2 chg 0000 evt 0002
<7>[ 29.972951] hub 2-0:1.0: state 7 ports 2 chg 0000 evt 0002
<7>[ 29.972957] ohci_hcd 0000:00:03.1: GetStatus roothub.portstatus [0] = 0x00010101 CSC PPS CCS
<7>[ 29.972962] hub 2-0:1.0: port 1, status 0101, change 0001, 12 Mb/s
<6>[ 30.034746] ACPI: PCI Interrupt 0000:00:03.3[D] -> GSI 23 (level, low) -> IRQ 21
<6>[ 30.054608] ehci_hcd 0000:00:03.3: EHCI Host Controller
<6>[ 30.072347] ehci_hcd 0000:00:03.3: new USB bus registered, assigned bus number 4
<7>[ 30.090141] ehci_hcd 0000:00:03.3: reset hcs_params 0x103206 dbg=1 cc=3 pcc=2 ordered !ppc ports=6
<7>[ 30.090146] ehci_hcd 0000:00:03.3: reset hcc_params 7070 thresh 7 uframes 1024
<7>[ 30.090187] PCI: cache line size of 128 is not supported by device 0000:00:03.3
<7>[ 30.090190] ehci_hcd 0000:00:03.3: supports USB remote wakeup
<6>[ 30.090200] ehci_hcd 0000:00:03.3: irq 21, io mem 0xe2024000
<7>[ 30.107916] hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x101
<7>[ 30.107944] ehci_hcd 0000:00:03.3: reset command 080002 (park)=0 ithresh=8 period=1024 Reset HALT
<7>[ 30.107952] ehci_hcd 0000:00:03.3: init command 010001 (park)=0 ithresh=1 period=1024 RUN
<6>[ 30.107957] ehci_hcd 0000:00:03.3: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
<7>[ 30.125785] usb usb4: default language 0x0409
<7>[ 30.125793] usb usb4: new device strings: Mfr=3, Product=2, SerialNumber=1
<6>[ 30.125796] usb usb4: Product: EHCI Host Controller
<6>[ 30.143765] usb usb4: Manufacturer: Linux 2.6.22-speedy ehci_hcd
<6>[ 30.161728] usb usb4: SerialNumber: 0000:00:03.3
<7>[ 30.179546] ohci_hcd 0000:00:03.1: GetStatus roothub.portstatus [0] = 0x00130100 PRSC PESC CSC PPS
<7>[ 30.179558] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
<7>[ 30.179575] hub 1-0:1.0: state 7 ports 2 chg 0000 evt 0002
<7>[ 30.179580] ohci_hcd 0000:00:03.0: GetStatus roothub.portstatus [0] = 0x00030300 PESC CSC LSDA PPS
<7>[ 30.179585] hub 1-0:1.0: port 1, status 0300, change 0003, 1.5 Mb/s
<6>[ 30.179588] usb 1-1: USB disconnect, address 2
<7>[ 30.197112] usb 1-1: unregistering device
<7>[ 30.197114] usb 1-1: usb_disable_device nuking all URBs
<7>[ 30.197119] usb 1-1: unregistering interface 1-1:1.0
<7>[ 30.197158] usb_endpoint usbdev1.2_ep81: ep_device_release called for usbdev1.2_ep81
<7>[ 30.197176] usb 1-1:1.0: uevent
<7>[ 30.197180] usb 1-1:1.0: uevent
<7>[ 30.197234] usb_endpoint usbdev1.2_ep00: ep_device_release called for usbdev1.2_ep00
<7>[ 30.197250] usb 1-1: uevent
<7>[ 30.197291] usb usb4: uevent
<7>[ 30.197303] usb usb4: usb_probe_device
<6>[ 30.197340] usb usb4: configuration #1 chosen from 1 choice
<7>[ 30.214898] usb usb4: adding 4-0:1.0 (config #1, interface 0)
<7>[ 30.214910] usb 4-0:1.0: uevent
<7>[ 30.214913] usb 4-0:1.0: uevent
<7>[ 30.214925] hub 4-0:1.0: usb_probe_interface
<7>[ 30.214927] hub 4-0:1.0: usb_probe_interface - got id
<6>[ 30.214930] hub 4-0:1.0: USB hub found
<6>[ 30.232332] hub 4-0:1.0: 6 ports detected
<7>[ 30.249621] hub 4-0:1.0: standalone hub
<7>[ 30.249623] hub 4-0:1.0: no power switching (usb 1.0)
<7>[ 30.249626] hub 4-0:1.0: individual port over-current protection
<7>[ 30.249629] hub 4-0:1.0: Single TT
<7>[ 30.249632] hub 4-0:1.0: TT requires at most 8 FS bit times (666 ns)
<7>[ 30.249635] hub 4-0:1.0: power on to power good time: 20ms
<7>[ 30.249640] hub 4-0:1.0: local power source is good
<7>[ 30.249642] hub 4-0:1.0: trying to enable port power on non-switchable hub
<7>[ 30.326909] hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x300
<7>[ 30.326918] hub 2-0:1.0: state 7 ports 2 chg 0000 evt 0002
<7>[ 30.326925] ohci_hcd 0000:00:03.1: GetStatus roothub.portstatus [0] = 0x00030100 PESC CSC PPS
<7>[ 30.326932] hub 2-0:1.0: port 1, status 0100, change 0003, 12 Mb/s
<7>[ 30.330998] ieee1394: Host added: ID:BUS[0-00:1023] GUID[000010dc001ecc82]
<6>[ 30.351035] ACPI: PCI Interrupt 0000:00:07.2[C] -> GSI 16 (level, low) -> IRQ 16
<6>[ 30.368610] ehci_hcd 0000:00:07.2: EHCI Host Controller
<6>[ 30.386138] ehci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 5
<7>[ 30.403788] ehci_hcd 0000:00:07.2: reset hcs_params 0x2204 dbg=0 cc=2 pcc=2 ordered !ppc ports=4
<7>[ 30.403793] ehci_hcd 0000:00:07.2: reset hcc_params 6872 thresh 7 uframes 256/512/1024
<7>[ 30.403843] ehci_hcd 0000:00:07.2: MWI active
<7>[ 30.403846] ehci_hcd 0000:00:07.2: supports USB remote wakeup
<6>[ 30.403857] ehci_hcd 0000:00:07.2: irq 16, io mem 0xe2026000
<7>[ 30.421321] ehci_hcd 0000:00:07.2: reset command 080002 (park)=0 ithresh=8 period=1024 Reset HALT
<7>[ 30.421328] ehci_hcd 0000:00:07.2: init command 010009 (park)=0 ithresh=1 period=256 RUN
<6>[ 30.421332] ehci_hcd 0000:00:07.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
<7>[ 30.438860] usb usb5: default language 0x0409
<7>[ 30.438869] usb usb5: new device strings: Mfr=3, Product=2, SerialNumber=1
<6>[ 30.438871] usb usb5: Product: EHCI Host Controller
<6>[ 30.456350] usb usb5: Manufacturer: Linux 2.6.22-speedy ehci_hcd
<7>[ 30.474023] hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x100
<7>[ 30.474029] hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0000
<7>[ 30.474035] ehci_hcd 0000:00:03.3: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
<7>[ 30.474042] hub 4-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
<6>[ 30.474047] usb usb5: SerialNumber: 0000:00:07.2
<7>[ 30.491714] usb usb5: uevent
<7>[ 30.491731] usb usb5: usb_probe_device
<6>[ 30.491771] usb usb5: configuration #1 chosen from 1 choice
<7>[ 30.509491] usb usb5: adding 5-0:1.0 (config #1, interface 0)
<7>[ 30.509510] usb 5-0:1.0: uevent
<7>[ 30.509513] usb 5-0:1.0: uevent
<7>[ 30.509526] hub 5-0:1.0: usb_probe_interface
<7>[ 30.509528] hub 5-0:1.0: usb_probe_interface - got id
<6>[ 30.509530] hub 5-0:1.0: USB hub found
<6>[ 30.527246] hub 5-0:1.0: 4 ports detected
<7>[ 30.544503] hub 5-0:1.0: standalone hub
<7>[ 30.544506] hub 5-0:1.0: no power switching (usb 1.0)
<7>[ 30.544508] hub 5-0:1.0: individual port over-current protection
<7>[ 30.544511] hub 5-0:1.0: Single TT
<7>[ 30.544514] hub 5-0:1.0: TT requires at most 8 FS bit times (666 ns)
<7>[ 30.544517] hub 5-0:1.0: power on to power good time: 20ms
<7>[ 30.544521] hub 5-0:1.0: local power source is good
<7>[ 30.544524] hub 5-0:1.0: trying to enable port power on non-switchable hub
<7>[ 30.606807] hub 4-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
<7>[ 30.606818] ehci_hcd 0000:00:03.3: port 1 low speed --> companion
<6>[ 30.647256] ACPI: PCI Interrupt 0000:00:07.0[A] -> GSI 18 (level, low) -> IRQ 22
<7>[ 30.664457] ehci_hcd 0000:00:03.3: GetStatus port 1 status 003002 POWER OWNER sig=se0 CSC
<7>[ 30.664479] ehci_hcd 0000:00:03.3: GetStatus port 2 status 001803 POWER sig=j CSC CONNECT
<7>[ 30.664486] hub 4-0:1.0: port 2, status 0501, change 0001, 480 Mb/s
<6>[ 30.664503] uhci_hcd 0000:00:07.0: UHCI Host Controller
<6>[ 30.681636] uhci_hcd 0000:00:07.0: new USB bus registered, assigned bus number 6
<6>[ 30.698836] uhci_hcd 0000:00:07.0: detected 2 ports
<7>[ 30.715817] uhci_hcd 0000:00:07.0: uhci_check_and_reset_hc: cmd = 0x0000
<7>[ 30.715820] uhci_hcd 0000:00:07.0: Performing full reset
<6>[ 30.715843] uhci_hcd 0000:00:07.0: irq 22, io base 0x0000e000
<7>[ 30.732755] usb usb6: default language 0x0409
<7>[ 30.732764] usb usb6: new device strings: Mfr=3, Product=2, SerialNumber=1
<6>[ 30.732766] usb usb6: Product: UHCI Host Controller
<6>[ 30.749603] usb usb6: Manufacturer: Linux 2.6.22-speedy uhci_hcd
<6>[ 30.766528] usb usb6: SerialNumber: 0000:00:07.0
<7>[ 30.783459] usb usb6: uevent
<7>[ 30.783476] usb usb6: usb_probe_device
<6>[ 30.783521] usb usb6: configuration #1 chosen from 1 choice
<7>[ 30.800325] hub 4-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x501
<7>[ 30.800354] usb usb6: adding 6-0:1.0 (config #1, interface 0)
<7>[ 30.800366] usb 6-0:1.0: uevent
<7>[ 30.800370] usb 6-0:1.0: uevent
<7>[ 30.800383] hub 6-0:1.0: usb_probe_interface
<7>[ 30.800386] hub 6-0:1.0: usb_probe_interface - got id
<6>[ 30.800388] hub 6-0:1.0: USB hub found
<6>[ 30.816995] hub 6-0:1.0: 2 ports detected
<7>[ 30.833658] hub 6-0:1.0: standalone hub
<7>[ 30.833660] hub 6-0:1.0: no power switching (usb 1.0)
<7>[ 30.833662] hub 6-0:1.0: individual port over-current protection
<7>[ 30.833665] hub 6-0:1.0: power on to power good time: 2ms
<7>[ 30.833669] hub 6-0:1.0: local power source is good
<7>[ 30.833671] hub 6-0:1.0: trying to enable port power on non-switchable hub
<7>[ 30.854760] ehci_hcd 0000:00:03.3: port 2 full speed --> companion
<7>[ 30.854767] ehci_hcd 0000:00:03.3: GetStatus port 2 status 003801 POWER OWNER sig=j CONNECT
<7>[ 30.854804] hub 4-0:1.0: port 2 not reset yet, waiting 50ms
<7>[ 30.910744] ehci_hcd 0000:00:03.3: GetStatus port 2 status 003002 POWER OWNER sig=se0 CSC
<7>[ 30.910773] hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0004
<7>[ 30.910779] hub 1-0:1.0: state 7 ports 2 chg 0000 evt 0002
<7>[ 30.910786] ohci_hcd 0000:00:03.0: GetStatus roothub.portstatus [0] = 0x00010301 CSC LSDA PPS CCS
<7>[ 30.910791] hub 1-0:1.0: port 1, status 0301, change 0001, 1.5 Mb/s
<6>[ 30.934870] ACPI: PCI Interrupt 0000:00:07.1[B] -> GSI 19 (level, low) -> IRQ 23
<6>[ 30.952065] uhci_hcd 0000:00:07.1: UHCI Host Controller
<6>[ 30.969096] uhci_hcd 0000:00:07.1: new USB bus registered, assigned bus number 7
<6>[ 30.985900] uhci_hcd 0000:00:07.1: detected 2 ports
<7>[ 31.002313] uhci_hcd 0000:00:07.1: uhci_check_and_reset_hc: cmd = 0x0000
<7>[ 31.002316] uhci_hcd 0000:00:07.1: Performing full reset
<6>[ 31.002341] uhci_hcd 0000:00:07.1: irq 23, io base 0x0000e400
<7>[ 31.018683] usb usb7: default language 0x0409
<7>[ 31.018691] usb usb7: new device strings: Mfr=3, Product=2, SerialNumber=1
<6>[ 31.018694] usb usb7: Product: UHCI Host Controller
<6>[ 31.034963] usb usb7: Manufacturer: Linux 2.6.22-speedy uhci_hcd
<7>[ 31.051281] ohci_hcd 0000:00:03.2: auto-stop root hub
<7>[ 31.051301] hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
<6>[ 31.051311] usb usb7: SerialNumber: 0000:00:07.1
<7>[ 31.067657] usb usb7: uevent
<7>[ 31.067677] usb usb7: usb_probe_device
<6>[ 31.067720] usb usb7: configuration #1 chosen from 1 choice
<7>[ 31.083828] usb usb7: adding 7-0:1.0 (config #1, interface 0)
<7>[ 31.083844] usb 7-0:1.0: uevent
<7>[ 31.083847] usb 7-0:1.0: uevent
<7>[ 31.083860] hub 7-0:1.0: usb_probe_interface
<7>[ 31.083862] hub 7-0:1.0: usb_probe_interface - got id
<6>[ 31.083865] hub 7-0:1.0: USB hub found
<6>[ 31.099887] hub 7-0:1.0: 2 ports detected
<7>[ 31.115812] hub 7-0:1.0: standalone hub
<7>[ 31.115814] hub 7-0:1.0: no power switching (usb 1.0)
<7>[ 31.115816] hub 7-0:1.0: individual port over-current protection
<7>[ 31.115819] hub 7-0:1.0: power on to power good time: 2ms
<7>[ 31.115824] hub 7-0:1.0: local power source is good
<7>[ 31.115827] hub 7-0:1.0: trying to enable port power on non-switchable hub
<7>[ 31.122650] ohci_hcd 0000:00:03.0: GetStatus roothub.portstatus [0] = 0x00100303 PRSC LSDA PPS PES CCS
<6>[ 31.177917] usb 1-1: new low speed USB device using ohci_hcd and address 3
<6>[ 31.218426] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
<6>[ 31.237948] ACPI: PCI Interrupt 0000:00:04.0[A] -> GSI 19 (level, low) -> IRQ 23
<6>[ 31.255618] 0000:00:04.0: Unknown PHY transceiver found at address 0.
<7>[ 31.272206] ohci_hcd 0000:00:03.0: GetStatus roothub.portstatus [0] = 0x00100303 PRSC LSDA PPS PES CCS
<6>[ 31.272978] 0000:00:04.0: Realtek RTL8201 PHY transceiver found at address 1.
<6>[ 31.290291] 0000:00:04.0: Unknown PHY transceiver found at address 2.
<6>[ 31.307539] 0000:00:04.0: Unknown PHY transceiver found at address 3.
<6>[ 31.324593] 0000:00:04.0: Unknown PHY transceiver found at address 4.
<6>[ 31.341488] 0000:00:04.0: Unknown PHY transceiver found at address 5.
<6>[ 31.358180] 0000:00:04.0: Unknown PHY transceiver found at address 6.
<6>[ 31.378415] 0000:00:04.0: Unknown PHY transceiver found at address 7.
<6>[ 31.394854] 0000:00:04.0: Unknown PHY transceiver found at address 8.
<6>[ 31.411146] 0000:00:04.0: Unknown PHY transceiver found at address 9.
<6>[ 31.427198] 0000:00:04.0: Unknown PHY transceiver found at address 10.
<7>[ 31.442426] usb 1-1: skipped 1 descriptor after interface
<6>[ 31.443205] 0000:00:04.0: Unknown PHY transceiver found at address 11.
<7>[ 31.458399] usb 1-1: default language 0x0409
<6>[ 31.459175] 0000:00:04.0: Unknown PHY transceiver found at address 12.
<7>[ 31.474089] usb 1-1: new device strings: Mfr=0, Product=2, SerialNumber=0
<6>[ 31.474093] usb 1-1: Product: USB Optical Mouse
<7>[ 31.488807] usb 1-1: uevent
<7>[ 31.488828] usb 1-1: usb_probe_device
<6>[ 31.488879] usb 1-1: configuration #1 chosen from 1 choice
<6>[ 31.504175] 0000:00:04.0: Unknown PHY transceiver found at address 13.
<7>[ 31.518833] usb 1-1: adding 1-1:1.0 (config #1, interface 0)
<7>[ 31.518851] usb 1-1:1.0: uevent
<7>[ 31.518855] usb 1-1:1.0: uevent
<7>[ 31.518918] hub 5-0:1.0: state 7 ports 4 chg 0000 evt 0000
<7>[ 31.518930] ehci_hcd 0000:00:07.2: GetStatus port 2 status 001803 POWER sig=j CSC CONNECT
<7>[ 31.518936] hub 5-0:1.0: port 2, status 0501, change 0001, 480 Mb/s
<6>[ 31.519711] 0000:00:04.0: Unknown PHY transceiver found at address 14.
<6>[ 31.534966] 0000:00:04.0: Unknown PHY transceiver found at address 15.
<6>[ 31.550016] 0000:00:04.0: Unknown PHY transceiver found at address 16.
<6>[ 31.565382] 0000:00:04.0: Unknown PHY transceiver found at address 17.
<6>[ 31.580101] 0000:00:04.0: Unknown PHY transceiver found at address 18.
<6>[ 31.594673] 0000:00:04.0: Unknown PHY transceiver found at address 19.
<6>[ 31.609072] 0000:00:04.0: Unknown PHY transceiver found at address 20.
<6>[ 31.623301] 0000:00:04.0: Unknown PHY transceiver found at address 21.
<6>[ 31.637460] 0000:00:04.0: Unknown PHY transceiver found at address 22.
<6>[ 31.651491] 0000:00:04.0: Unknown PHY transceiver found at address 23.
<6>[ 31.665379] 0000:00:04.0: Unknown PHY transceiver found at address 24.
<7>[ 31.678226] hub 5-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x501
<6>[ 31.679009] 0000:00:04.0: Unknown PHY transceiver found at address 25.
<6>[ 31.692332] 0000:00:04.0: Unknown PHY transceiver found at address 26.
<6>[ 31.705493] 0000:00:04.0: Unknown PHY transceiver found at address 27.
<6>[ 31.718497] 0000:00:04.0: Unknown PHY transceiver found at address 28.
<6>[ 31.731333] 0000:00:04.0: Unknown PHY transceiver found at address 29.
<7>[ 31.743328] ehci_hcd 0000:00:07.2: port 2 high speed
<7>[ 31.743333] ehci_hcd 0000:00:07.2: GetStatus port 2 status 001005 POWER sig=se0 PE CONNECT
<6>[ 31.744102] 0000:00:04.0: Unknown PHY transceiver found at address 30.
<6>[ 31.756484] 0000:00:04.0: Unknown PHY transceiver found at address 31.
<6>[ 31.791907] 0000:00:04.0: Using transceiver found at address 1 as default
<6>[ 31.803445] usb 5-2: new high speed USB device using ehci_hcd and address 2
<6>[ 31.816112] eth0: SiS 900 PCI Fast Ethernet at 0xdc00, IRQ 23, 00:10:dc:c5:f1:83.
<6>[ 31.828648] ACPI: PCI Interrupt 0000:00:02.7[C] -> GSI 18 (level, low) -> IRQ 22
<7>[ 31.870682] ehci_hcd 0000:00:07.2: port 2 high speed
<7>[ 31.870689] ehci_hcd 0000:00:07.2: GetStatus port 2 status 001005 POWER sig=se0 PE CONNECT
<7>[ 31.946802] usb 5-2: new device strings: Mfr=0, Product=0, SerialNumber=0
<7>[ 31.946846] usb 5-2: uevent
<7>[ 31.946869] usb 5-2: usb_probe_device
<6>[ 31.946916] usb 5-2: configuration #1 chosen from 1 choice
<7>[ 31.959553] usb 5-2: adding 5-2:1.0 (config #1, interface 0)
<7>[ 31.959577] usb 5-2:1.0: uevent
<7>[ 31.959581] usb 5-2:1.0: uevent
<7>[ 31.959598] hub 5-2:1.0: usb_probe_interface
<7>[ 31.959600] hub 5-2:1.0: usb_probe_interface - got id
<6>[ 31.959603] hub 5-2:1.0: USB hub found
<6>[ 31.972044] hub 5-2:1.0: 2 ports detected
<7>[ 31.984146] hub 5-2:1.0: compound device; port removable status: FR
<7>[ 31.984149] hub 5-2:1.0: ganged power switching
<7>[ 31.984151] hub 5-2:1.0: global over-current protection
<7>[ 31.984153] hub 5-2:1.0: Single TT
<7>[ 31.984155] hub 5-2:1.0: TT requires at most 8 FS bit times (666 ns)
<7>[ 31.984161] hub 5-2:1.0: power on to power good time: 100ms
<7>[ 31.984414] hub 5-2:1.0: local power source is good
<7>[ 31.984417] hub 5-2:1.0: no over-current condition exists
<7>[ 31.984420] hub 5-2:1.0: enabling power on all ports
<7>[ 32.086353] usb 5-2: link qh256-0001/c5f3e100 start 255 [1/0 us]
<7>[ 32.086479] hub 2-0:1.0: state 7 ports 2 chg 0000 evt 0002
<7>[ 32.086488] ohci_hcd 0000:00:03.1: GetStatus roothub.portstatus [0] = 0x00010101 CSC PPS CCS
<7>[ 32.086493] hub 2-0:1.0: port 1, status 0101, change 0001, 12 Mb/s
<6>[ 32.086517] usbcore: registered new interface driver hiddev
<6>[ 32.162333] intel8x0_measure_ac97_clock: measured 52676 usecs
<6>[ 32.174473] intel8x0: clocking to 48000
<6>[ 32.186724] ACPI: PCI Interrupt 0000:00:08.0[A] -> GSI 19 (level, low) -> IRQ 23
<6>[ 32.198917] saa7134[0]: found at 0000:00:08.0, rev: 1, irq: 23, latency: 32, mmio: 0xe2027000
<6>[ 32.211353] saa7134[0]: subsystem: 16be:0003, board: Medion 7134 [card=12,autodetected]
<7>[ 32.223909] hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x101
<6>[ 32.232264] saa7134[0]: board init: gpio is 0
<7>[ 32.298279] ohci_hcd 0000:00:03.1: GetStatus roothub.portstatus [0] = 0x00100103 PRSC PPS PES CCS
<6>[ 32.354258] usb 2-1: new full speed USB device using ohci_hcd and address 3
<6>[ 32.390255] saa7134[0]: i2c eeprom 00: be 16 03 00 08 20 1c 55 43 43 a9 1c 55 43 43 a9
<6>[ 32.403241] saa7134[0]: i2c eeprom 10: ff ff ff ff 15 00 0e 01 0c c0 08 00 00 00 00 00
<6>[ 32.416115] saa7134[0]: i2c eeprom 20: 00 00 00 e3 ff ff ff ff ff ff ff ff ff ff ff ff
<6>[ 32.429065] saa7134[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
<7>[ 32.441774] ohci_hcd 0000:00:03.1: GetStatus roothub.portstatus [0] = 0x00100103 PRSC PPS PES CCS
<6>[ 32.441780] saa7134[0]: i2c eeprom 40: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
<6>[ 32.454366] saa7134[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
<6>[ 32.466746] saa7134[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
<6>[ 32.478972] saa7134[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
<6>[ 32.506206] saa7134[0] Tuner type is 38
<7>[ 32.518027] usb 2-1: ep0 maxpacket = 8
<7>[ 32.528660] usb 2-1: default language 0x0409
<7>[ 32.537660] usb 2-1: new device strings: Mfr=1, Product=2, SerialNumber=3
<6>[ 32.537664] usb 2-1: Product: Medion Flash XL V3.0C
<6>[ 32.549438] usb 2-1: Manufacturer: MEDION
<6>[ 32.561308] usb 2-1: SerialNumber: 2003-02
<7>[ 32.572931] usb 2-1: uevent
<7>[ 32.572955] usb 2-1: usb_probe_device
<6>[ 32.573012] usb 2-1: configuration #1 chosen from 1 choice
<7>[ 32.588650] usb 2-1: adding 2-1:1.0 (config #1, interface 0)
<7>[ 32.588692] usb 2-1:1.0: uevent
<7>[ 32.588696] usb 2-1:1.0: uevent
<7>[ 32.591779] hub 6-0:1.0: state 7 ports 2 chg 0000 evt 0006
<7>[ 32.591792] uhci_hcd 0000:00:07.0: port 1 portsc 008a,00
<7>[ 32.591802] hub 6-0:1.0: port 1, status 0100, change 0003, 12 Mb/s
<6>[ 32.634204] tuner 1-0043: chip found @ 0x86 (saa7134[0])
<6>[ 32.645840] tda9887 1-0043: tda988[5/6/7] found @ 0x43 (tuner)
<4>[ 32.674167] tuner 1-0060: All bytes are equal. It is not a TEA5767
<6>[ 32.685974] tuner 1-0060: chip found @ 0xc0 (saa7134[0])
<6>[ 32.697676] tuner 1-0060: type set to 38 (Philips PAL/SECAM multi (FM1216ME MK3))
<6>[ 32.709449] tuner 1-0060: type set to 38 (Philips PAL/SECAM multi (FM1216ME MK3))
<6>[ 32.723373] saa7134[0]: registered device video0 [v4l2]
<7>[ 32.735064] hub 6-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x100
<7>[ 32.735071] uhci_hcd 0000:00:07.0: port 2 portsc 008a,00
<7>[ 32.735080] hub 6-0:1.0: port 2, status 0100, change 0003, 12 Mb/s
<6>[ 32.735104] saa7134[0]: registered device vbi0
<6>[ 32.746601] saa7134[0]: registered device radio0
<7>[ 32.862116] hub 6-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x100
<7>[ 32.862125] hub 1-0:1.0: state 7 ports 2 chg 0000 evt 0002
<7>[ 32.862134] hub 7-0:1.0: state 7 ports 2 chg 0000 evt 0006
<7>[ 32.862141] uhci_hcd 0000:00:07.1: port 1 portsc 008a,00
<7>[ 32.862150] hub 7-0:1.0: port 1, status 0100, change 0003, 12 Mb/s
<5>[ 32.913919] SCSI subsystem initialized
<7>[ 32.990088] hub 7-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x100
<7>[ 32.990097] uhci_hcd 0000:00:07.1: port 2 portsc 008a,00
<7>[ 32.990106] hub 7-0:1.0: port 2, status 0100, change 0003, 12 Mb/s
<6>[ 33.014319] Initializing USB Mass Storage driver...
<3>[ 33.045021] saa7134[0]/dvb: frontend initialization failed
<7>[ 33.121200] hub 7-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x100
<7>[ 33.121209] hub 5-2:1.0: state 7 ports 2 chg 0000 evt 0002
<7>[ 33.121235] usbhid 1-1:1.0: usb_probe_interface
<7>[ 33.121238] usbhid 1-1:1.0: usb_probe_interface - got id
<7>[ 33.121450] hub 5-2:1.0: port 1, status 0101, change 0001, 12 Mb/s
<6>[ 33.126508] input: USB Optical Mouse as /class/input/input3
<6>[ 33.137731] input: USB HID v1.11 Mouse [USB Optical Mouse] on usb-0000:00:03.0-1
<7>[ 33.249304] hub 5-2:1.0: debounce: port 1: total 100ms stable 100ms status 0x101
<6>[ 33.321165] usb 5-2.1: new high speed USB device using ehci_hcd and address 3
<7>[ 33.345159] hub 5-2:1.0: port 1 not reset yet, waiting 10ms
<7>[ 33.437393] usb 5-2.1: new device strings: Mfr=0, Product=0, SerialNumber=0
<7>[ 33.437428] usb 5-2.1: uevent
<7>[ 33.437445] usb 5-2.1: usb_probe_device
<6>[ 33.437502] usb 5-2.1: configuration #1 chosen from 1 choice
<7>[ 33.449395] usb 5-2.1: adding 5-2.1:1.0 (config #1, interface 0)
<7>[ 33.449418] usb 5-2.1:1.0: uevent
<7>[ 33.449422] usb 5-2.1:1.0: uevent
<7>[ 33.449440] hub 5-2.1:1.0: usb_probe_interface
<7>[ 33.449442] hub 5-2.1:1.0: usb_probe_interface - got id
<6>[ 33.449445] hub 5-2.1:1.0: USB hub found
<6>[ 33.461388] hub 5-2.1:1.0: 4 ports detected
<7>[ 33.473182] hub 5-2.1:1.0: compound device; port removable status: FRRR
<7>[ 33.473184] hub 5-2.1:1.0: ganged power switching
<7>[ 33.473187] hub 5-2.1:1.0: global over-current protection
<7>[ 33.473441] hub 5-2.1:1.0: TT per port
<7>[ 33.473444] hub 5-2.1:1.0: TT requires at most 8 FS bit times (666 ns)
<7>[ 33.473447] hub 5-2.1:1.0: power on to power good time: 100ms
<7>[ 33.473634] hub 5-2.1:1.0: local power source is good
<7>[ 33.473637] hub 5-2.1:1.0: no over-current condition exists
<7>[ 33.473639] hub 5-2.1:1.0: enabling power on all ports
<7>[ 33.577043] usb 5-2.1: link qh256-0001/c5f3e200 start 255 [1/0 us]
<7>[ 33.577255] hub 2-0:1.0: state 7 ports 2 chg 0000 evt 0002
<7>[ 33.577265] hub 6-0:1.0: state 7 ports 2 chg 0000 evt 0000
<7>[ 33.577268] hub 5-2.1:1.0: state 7 ports 4 chg 0000 evt 0000
<7>[ 33.577291] usb-storage 2-1:1.0: usb_probe_interface
<7>[ 33.577298] usb-storage 2-1:1.0: usb_probe_interface - got id
<6>[ 33.577391] scsi0 : SCSI emulation for USB Mass Storage devices
<7>[ 33.589562] hub 5-2.1:1.0: port 1, status 0101, change 0001, 12 Mb/s
<7>[ 33.589622] usb-storage: device found at 3
<7>[ 33.589625] usb-storage: waiting for device to settle before scanning
<7>[ 33.717091] hub 5-2.1:1.0: debounce: port 1: total 100ms stable 100ms status 0x101
<6>[ 33.789078] usb 5-2.1.1: new high speed USB device using ehci_hcd and address 4
<7>[ 33.821069] hub 5-2.1:1.0: port 1 not reset yet, waiting 10ms
<7>[ 33.933300] usb 5-2.1.1: skipped 1 descriptor after endpoint
<7>[ 33.940545] usb 5-2.1.1: default language 0x0409
<7>[ 33.979789] usb 5-2.1.1: new device strings: Mfr=1, Product=2, SerialNumber=3
<6>[ 33.979792] usb 5-2.1.1: Product: Flash Card Reader
<6>[ 33.992351] usb 5-2.1.1: Manufacturer: Generic
<7>[ 34.004823] usb usb6: suspend_rh (auto-stop)
<6>[ 34.004838] usb 5-2.1.1: SerialNumber: 26020128B005
<7>[ 34.017449] usb usb7: suspend_rh (auto-stop)
<7>[ 34.017498] usb 5-2.1.1: uevent
<7>[ 34.017519] usb 5-2.1.1: usb_probe_device
<6>[ 34.017579] usb 5-2.1.1: configuration #1 chosen from 1 choice
<7>[ 34.030406] usb 5-2.1.1: adding 5-2.1.1:1.0 (config #1, interface 0)
<7>[ 34.030422] usb 5-2.1.1:1.0: uevent
<7>[ 34.030426] usb 5-2.1.1:1.0: uevent
<7>[ 34.030906] hub 5-2.1:1.0: state 7 ports 4 chg 0000 evt 0002
<6>[ 34.031542] usbcore: registered new interface driver usbhid
<6>[ 34.044775] drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
<7>[ 34.057930] usb-storage 5-2.1.1:1.0: usb_probe_interface
<7>[ 34.057936] usb-storage 5-2.1.1:1.0: usb_probe_interface - got id
<6>[ 34.057987] scsi1 : SCSI emulation for USB Mass Storage devices
<7>[ 34.071131] usb-storage: device found at 4
<7>[ 34.071134] usb-storage: waiting for device to settle before scanning
<6>[ 34.071152] usbcore: registered new interface driver usb-storage
<6>[ 34.084240] USB Mass Storage support registered.
<6>[ 34.411494] Adding 27189972k swap on /dev/hdb11. Priority:-1 extents:1 across:27189972k
<4>[ 34.619907] fuse init (API version 7.8)
<6>[ 35.742131] device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
<5>[ 38.629647] scsi 0:0:0:0: Direct-Access Medion Flash XL CF 3.0C PQ: 0 ANSI: 0 CCS
<5>[ 38.651420] scsi 0:0:0:1: Direct-Access Medion Flash XL MS 3.0C PQ: 0 ANSI: 0 CCS
<5>[ 38.673632] scsi 0:0:0:2: Direct-Access Medion Flash XL MMC/SD 3.0C PQ: 0 ANSI: 0 CCS
<5>[ 38.680436] scsi 0:0:0:3: Direct-Access Medion Flash XL SM 3.0C PQ: 0 ANSI: 0 CCS
<7>[ 38.718908] usb-storage: device scan complete
<5>[ 38.859617] sd 0:0:0:0: [sda] Attached SCSI removable disk
<5>[ 38.886919] sd 0:0:0:1: [sdb] Attached SCSI removable disk
<5>[ 38.915016] sd 0:0:0:2: [sdc] Attached SCSI removable disk
<5>[ 39.051675] sd 0:0:0:3: [sdd] Attached SCSI removable disk
<5>[ 39.080275] scsi 1:0:0:0: Direct-Access Generic Flash HS-CF 4.44 PQ: 0 ANSI: 0
<5>[ 39.101133] sd 1:0:0:0: [sde] Attached SCSI removable disk
<5>[ 39.121756] scsi 1:0:0:1: Direct-Access Generic Flash HS-COMBO 4.44 PQ: 0 ANSI: 0
<6>[ 39.142494] loop: module loaded
<5>[ 39.160980] sd 0:0:0:0: Attached scsi generic sg0 type 0
<5>[ 39.178094] sd 0:0:0:1: Attached scsi generic sg1 type 0
<5>[ 39.195142] sd 0:0:0:2: Attached scsi generic sg2 type 0
<5>[ 39.212070] sd 0:0:0:3: Attached scsi generic sg3 type 0
<5>[ 39.228703] sd 1:0:0:0: Attached scsi generic sg4 type 0
<5>[ 39.245147] sd 1:0:0:1: [sdf] Attached SCSI removable disk
<5>[ 39.261436] sd 1:0:0:1: Attached scsi generic sg5 type 0
<7>[ 39.278102] usb-storage: device scan complete
<6>[ 39.402085] kjournald starting. Commit interval 5 seconds
<6>[ 39.418471] EXT3 FS on hdb8, internal journal
<6>[ 39.440739] EXT3-fs: mounted filesystem with ordered data mode.
<6>[ 39.483405] kjournald starting. Commit interval 5 seconds
<6>[ 39.499780] EXT3 FS on hdb9, internal journal
<6>[ 39.516054] EXT3-fs: mounted filesystem with ordered data mode.
<6>[ 39.569724] kjournald starting. Commit interval 5 seconds
<6>[ 39.586305] EXT3 FS on hdb10, internal journal
<6>[ 39.602611] EXT3-fs: mounted filesystem with ordered data mode.
<7>[ 39.685810] ISO 9660 Extensions: Microsoft Joliet Level 3
<7>[ 39.741211] ISO 9660 Extensions: RRIP_1991A
<6>[ 39.796165] SGI XFS with ACLs, security attributes, realtime, no debug enabled
<6>[ 39.813088] SGI XFS Quota Management subsystem
<5>[ 39.896628] XFS mounting filesystem hdb12
<7>[ 39.999452] Ending clean XFS mount for filesystem: hdb12
Kernel logging (ksyslog) stopped.
Kernel log daemon terminating.
Boot logging started on /dev/tty1(/dev/console) at Sat Sep 15 18:49:09 2007
Boot of 2.6.23rc6 with CONFIG_PRINTK_TIME and CONFIG_USB_DEBUG
klogd 1.4.1, log source = ksyslog started.
<5>[ 0.000000] Linux version 2.6.23-rc6-speedy (root@speedy) (gcc version 4.1.2 20061115 (prerelease) (SUSE Linux)) #2 PREEMPT Sat Sep 15 18:44:45 CEST 2007
<6>[ 0.000000] BIOS-provided physical RAM map:
<4>[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
<4>[ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
<4>[ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
<4>[ 0.000000] BIOS-e820: 0000000000100000 - 000000005fff0000 (usable)
<4>[ 0.000000] BIOS-e820: 000000005fff0000 - 000000005fff3000 (ACPI NVS)
<4>[ 0.000000] BIOS-e820: 000000005fff3000 - 0000000060000000 (ACPI data)
<5>[ 0.000000] 639MB HIGHMEM available.
<5>[ 0.000000] 896MB LOWMEM available.
<6>[ 0.000000] found SMP MP-table at 000f5980
<7>[ 0.000000] Entering add_active_range(0, 0, 393200) 0 entries of 256 used
<4>[ 0.000000] Zone PFN ranges:
<4>[ 0.000000] DMA 0 -> 4096
<4>[ 0.000000] Normal 4096 -> 229376
<4>[ 0.000000] HighMem 229376 -> 393200
<4>[ 0.000000] Movable zone start PFN for each node
<4>[ 0.000000] early_node_map[1] active PFN ranges
<4>[ 0.000000] 0: 0 -> 393200
<7>[ 0.000000] On node 0 totalpages: 393200
<7>[ 0.000000] DMA zone: 32 pages used for memmap
<7>[ 0.000000] DMA zone: 0 pages reserved
<7>[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
<7>[ 0.000000] Normal zone: 1760 pages used for memmap
<7>[ 0.000000] Normal zone: 223520 pages, LIFO batch:31
<7>[ 0.000000] HighMem zone: 1279 pages used for memmap
<7>[ 0.000000] HighMem zone: 162545 pages, LIFO batch:31
<7>[ 0.000000] Movable zone: 0 pages used for memmap
<6>[ 0.000000] DMI 2.3 present.
<4>[ 0.000000] ACPI: RSDP 000F7350, 0014 (r0 AWARD )
<4>[ 0.000000] ACPI: RSDT 5FFF3000, 002C (r1 AWARD AWRDACPI 42302E31 AWRD 0)
<4>[ 0.000000] ACPI: FACP 5FFF3040, 0074 (r1 AWARD AWRDACPI 42302E31 AWRD 0)
<4>[ 0.000000] ACPI: DSDT 5FFF30C0, 38BB (r1 AWARD AWRDACPI 1000 MSFT 100000D)
<4>[ 0.000000] ACPI: FACS 5FFF0000, 0040
<4>[ 0.000000] ACPI: APIC 5FFF6980, 0054 (r1 AWARD AWRDACPI 42302E31 AWRD 0)
<6>[ 0.000000] ACPI: PM-Timer IO Port: 0x1008
<7>[ 0.000000] ACPI: Local APIC address 0xfee00000
<6>[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
<4>[ 0.000000] Processor #0 15:2 APIC version 20
<6>[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
<4>[ 0.000000] IOAPIC[0]: apic_id 2, version 20, address 0xfec00000, GSI 0-23
<6>[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
<6>[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 dfl dfl)
<7>[ 0.000000] ACPI: IRQ0 used by override.
<7>[ 0.000000] ACPI: IRQ2 used by override.
<7>[ 0.000000] ACPI: IRQ9 used by override.
<4>[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
<6>[ 0.000000] Using ACPI (MADT) for SMP configuration information
<4>[ 0.000000] Allocating PCI resources starting at 70000000 (gap: 60000000:a0000000)
<4>[ 0.000000] swsusp: Registered nosave memory region: 000000000009f000 - 00000000000a0000
<4>[ 0.000000] swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000f0000
<4>[ 0.000000] swsusp: Registered nosave memory region: 00000000000f0000 - 0000000000100000
<4>[ 0.000000] Built 1 zonelists in Zone order. Total pages: 390129
<5>[ 0.000000] Kernel command line: root=/dev/hdb7 vga=0x346 resume=/dev/hdb11 splash=verbose console=tty0 crashkernel=64M@16M 3
<7>[ 0.000000] mapped APIC to ffffb000 (fee00000)
<7>[ 0.000000] mapped IOAPIC to ffffa000 (fec00000)
<6>[ 0.000000] Enabling fast FPU save and restore... done.
<6>[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
<6>[ 0.000000] Initializing CPU#0
<4>[ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
<4>[ 0.000000] Detected 2672.794 MHz processor.
<4>[ 16.900420] Console: colour dummy device 80x25
<6>[ 16.900425] console [tty0] enabled
<6>[ 16.901192] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
<6>[ 16.901971] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
<6>[ 16.951370] Memory: 1490028k/1572800k available (1740k kernel code, 81432k reserved, 672k data, 196k init, 655296k highmem)
<4>[ 16.951391] virtual kernel memory layout:
<4>[ 16.951393] fixmap : 0xfffa8000 - 0xfffff000 ( 348 kB)
<4>[ 16.951394] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
<4>[ 16.951395] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
<4>[ 16.951397] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
<4>[ 16.951398] .init : 0xc125e000 - 0xc128f000 ( 196 kB)
<4>[ 16.951399] .data : 0xc11b3206 - 0xc125b564 ( 672 kB)
<4>[ 16.951400] .text : 0xc1000000 - 0xc11b3206 (1740 kB)
<4>[ 16.951418] Checking if this processor honours the WP bit even in supervisor mode... Ok.
<4>[ 17.031546] Calibrating delay using timer specific routine.. 5349.30 BogoMIPS (lpj=10698619)
<6>[ 17.031596] Security Framework v1.0.0 initialized
<4>[ 17.031618] Mount-cache hash table entries: 512
<7>[ 17.031766] CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 00000400 00000000 00000000 00000000
<6>[ 17.031779] CPU: Trace cache: 12K uops, L1 D cache: 8K
<6>[ 17.031783] CPU: L2 cache: 512K
<7>[ 17.031786] CPU: After all inits, caps: bfebfbff 00000000 00000000 0000b080 00000400 00000000 00000000 00000000
<6>[ 17.031793] Intel machine check architecture supported.
<6>[ 17.031799] Intel machine check reporting enabled on CPU#0.
<6>[ 17.031803] CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
<6>[ 17.031808] CPU0: Thermal monitoring enabled
<4>[ 17.031817] Compat vDSO mapped to ffffe000.
<4>[ 17.031830] CPU: Intel(R) Pentium(R) 4 CPU 2.66GHz stepping 07
<6>[ 17.031839] Checking 'hlt' instruction... OK.
<6>[ 17.047750] ACPI: Core revision 20070126
<4>[ 17.155150] ENABLING IO-APIC IRQs
<6>[ 17.155322] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
<6>[ 17.299758] NET: Registered protocol family 16
<6>[ 17.299975] ACPI: bus type pci registered
<6>[ 17.339368] PCI: PCI BIOS revision 2.10 entry at 0xfb400, last bus=1
<6>[ 17.339373] PCI: Using configuration type 1
<4>[ 17.339376] Setting up standard PCI resources
<7>[ 17.348254] ACPI: EC: Look up EC in DSDT
<6>[ 17.351549] ACPI: Interpreter enabled
<6>[ 17.351557] ACPI: (supports S0 S3)
<6>[ 17.351576] ACPI: Using IOAPIC for interrupt routing
<6>[ 17.356558] ACPI: PCI Root Bridge [PCI0] (0000:00)
<6>[ 17.356855] Enabling SiS 96x SMBus.
<7>[ 17.358446] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
<6>[ 17.381947] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
<6>[ 17.382070] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
<6>[ 17.382181] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 *7 9 10 11 12 14 15)
<6>[ 17.382292] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
<6>[ 17.382399] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
<6>[ 17.382517] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
<6>[ 17.382627] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
<6>[ 17.382734] ACPI: PCI Interrupt Link [LNKH] (IRQs *3 4 5 6 7 9 10 11 12 14 15)
<6>[ 17.382871] Linux Plug and Play Support v0.97 (c) Adam Belay
<6>[ 17.382908] pnp: PnP ACPI init
<6>[ 17.382921] ACPI: bus type pnp registered
<6>[ 17.385176] pnp: PnP ACPI: found 11 devices
<6>[ 17.385182] ACPI: ACPI bus type pnp unregistered
<6>[ 17.385189] PnPBIOS: Disabled by ACPI PNP
<6>[ 17.385432] PCI: Using ACPI for IRQ routing
<6>[ 17.385438] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
<6>[ 17.411448] Time: tsc clocksource has been installed.
<6>[ 17.419490] pnp: 00:00: iomem range 0xd0000-0xd3fff has been reserved
<6>[ 17.419496] pnp: 00:00: iomem range 0xf0000-0xf7fff could not be reserved
<6>[ 17.419501] pnp: 00:00: iomem range 0xf8000-0xfbfff could not be reserved
<6>[ 17.419505] pnp: 00:00: iomem range 0xfc000-0xfffff could not be reserved
<6>[ 17.449881] PCI: Bridge: 0000:00:01.0
<6>[ 17.449886] IO window: disabled.
<6>[ 17.449896] MEM window: e0000000-e1ffffff
<6>[ 17.449904] PREFETCH window: d8000000-dfffffff
<6>[ 17.449949] NET: Registered protocol family 2
<6>[ 17.487459] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
<6>[ 17.487630] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
<6>[ 17.488802] TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
<6>[ 17.489195] TCP: Hash tables configured (established 131072 bind 65536)
<6>[ 17.489201] TCP reno registered
<6>[ 17.499608] checking if image is initramfs... it is
<6>[ 17.731599] Freeing initrd memory: 2802k freed
<6>[ 17.731859] Machine check exception polling timer started.
<6>[ 17.731889] apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
<5>[ 17.731894] apm: overridden by ACPI.
<6>[ 17.732247] audit: initializing netlink socket (disabled)
<5>[ 17.732268] audit(1189882252.576:1): initialized
<4>[ 17.732360] highmem bounce pool size: 64 pages
<4>[ 17.732365] Total HugeTLB memory allocated, 0
<6>[ 17.732506] io scheduler noop registered
<6>[ 17.732510] io scheduler anticipatory registered
<6>[ 17.732513] io scheduler deadline registered
<6>[ 17.732525] io scheduler cfq registered (default)
<7>[ 17.815344] pci 0000:00:07.0: uhci_check_and_reset_hc: legsup = 0x2000
<7>[ 17.815347] pci 0000:00:07.0: Performing full reset
<7>[ 17.815364] pci 0000:00:07.1: uhci_check_and_reset_hc: legsup = 0x2000
<7>[ 17.815367] pci 0000:00:07.1: Performing full reset
<7>[ 17.815395] Boot video device is 0000:01:00.0
<6>[ 17.815683] vesafb: framebuffer at 0xd8000000, mapped to 0xf8880000, using 7500k, total 131072k
<6>[ 17.815691] vesafb: mode is 1600x1200x16, linelength=3200, pages=1
<6>[ 17.815695] vesafb: protected mode interface info at c000:def0
<6>[ 17.815699] vesafb: pmi: set display start = c00cdf35, set palette = c00cdfba
<6>[ 17.815703] vesafb: pmi: ports = b4c3 b503 ba03 c003 c103 c403 c503 c603 c703 c803 c903 cc03 ce03 cf03 d003 d103 d203 d303 d403 d503 da03 ff03
<6>[ 17.815725] vesafb: scrolling: redraw
<6>[ 17.815730] vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
<4>[ 17.881948] Console: switching to colour frame buffer device 200x75
<6>[ 17.948327] fb0: VESA VGA frame buffer device
<6>[ 17.948624] isapnp: Scanning for PnP cards...
<6>[ 17.975278] Switched to NOHz mode on CPU #0
<6>[ 18.259227] isapnp: No Plug & Play device found
<6>[ 18.266523] Real Time Clock Driver v1.12ac
<6>[ 18.266847] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
<6>[ 18.267355] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
<6>[ 18.268169] 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
<6>[ 18.268661] Floppy drive(s): fd0 is 1.44M
<6>[ 18.286905] FDC 0 is a post-1991 82077
<4>[ 18.288703] RAMDISK driver initialized: 16 RAM disks of 64000K size 1024 blocksize
<6>[ 18.289277] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
<6>[ 18.289930] serio: i8042 KBD port at 0x60,0x64 irq 1
<6>[ 18.290189] serio: i8042 AUX port at 0x60,0x64 irq 12
<6>[ 18.290609] mice: PS/2 mouse device common for all mice
<6>[ 18.323758] input: AT Translated Set 2 keyboard as /class/input/input0
<6>[ 18.332551] input: PC Speaker as /class/input/input1
<6>[ 18.974061] input: ImPS/2 Generic Wheel Mouse as /class/input/input2
<6>[ 18.978850] NET: Registered protocol family 1
<4>[ 18.979085] Using IPI Shortcut mode
<6>[ 18.979705] Freeing unused kernel memory: 196k freed
<6>[ 19.294594] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
<6>[ 19.294945] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
<6>[ 19.318427] ACPI: Thermal Zone [THRM] (46 C)
<6>[ 19.325069] SIS5513: IDE controller at PCI slot 0000:00:02.5
<6>[ 19.325410] ACPI: PCI Interrupt 0000:00:02.5[A] -> GSI 16 (level, low) -> IRQ 16
<6>[ 19.325814] SIS5513: chipset revision 0
<6>[ 19.326016] SIS5513: not 100% native mode: will probe irqs later
<6>[ 19.326349] SIS5513: SiS 962/963 MuTIOL IDE UDMA133 controller
<6>[ 19.326669] ide0: BM-DMA at 0x4000-0x4007, BIOS settings: hda:DMA, hdb:DMA
<6>[ 19.327083] ide1: BM-DMA at 0x4008-0x400f, BIOS settings: hdc:DMA, hdd:DMA
<7>[ 19.327479] Probing IDE interface ide0...
<4>[ 19.614934] hda: ST3120023A, ATA DISK drive
<4>[ 19.894731] hdb: SAMSUNG SP2514N, ATA DISK drive
<7>[ 19.950794] hda: selected mode 0x45
<7>[ 19.963687] hdb: selected mode 0x45
<4>[ 19.980228] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
<6>[ 19.989612] hda: max request size: 128KiB
<6>[ 19.990047] hda: 234441648 sectors (120034 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(100)
<6>[ 19.990666] hda: cache flushes supported
<6>[ 19.990904] hda: hda1 hda2 < hda5 hda6 hda7 hda8 hda9 hda10 hda11 >
<6>[ 20.082750] hdb: max request size: 512KiB
<6>[ 20.098815] hdb: 488397168 sectors (250059 MB) w/8192KiB Cache, CHS=30401/255/63, UDMA(100)
<6>[ 20.101746] hdb: cache flushes supported
<6>[ 20.102026] hdb: hdb1 hdb2 < hdb5 hdb6 hdb7 hdb8 hdb9 hdb10 hdb11 hdb12 >
<7>[ 20.259090] Probing IDE interface ide1...
<4>[ 21.010319] hdc: IDE DVD-ROM 16X, ATAPI CD/DVD-ROM drive
<4>[ 21.810021] hdd: _NEC DVD_RW ND-1300A, ATAPI CD/DVD-ROM drive
<7>[ 21.882711] hdc: selected mode 0x42
<7>[ 21.883906] hdd: selected mode 0x42
<4>[ 21.884072] ide1 at 0x170-0x177,0x376 on irq 15
<6>[ 21.913490] ACPI: Fan [FAN] (on)
<6>[ 21.953538] BIOS EDD facility v0.16 2004-Jun-25, 6 devices found
<4>[ 22.106255] swsusp: Marking nosave pages: 000000000009f000 - 0000000000100000
<4>[ 22.106260] swsusp: Basic memory bitmaps created
<4>[ 22.114449] swsusp: Basic memory bitmaps freed
<4>[ 22.122212] Attempting manual resume
<6>[ 22.246776] kjournald starting. Commit interval 5 seconds
<6>[ 22.246906] EXT3 FS on hdb7, internal journal
<6>[ 22.246916] EXT3-fs: mounted filesystem with ordered data mode.
<6>[ 25.074963] lp: driver loaded but no devices found
<6>[ 26.811082] Linux agpgart interface v0.102
<6>[ 26.866255] ACPI: PCI Interrupt 0000:00:02.3[B] -> GSI 17 (level, low) -> IRQ 17
<6>[ 26.965764] sis900.c: v1.08.10 Apr. 2 2006
<6>[ 26.990844] usbcore: registered new interface driver usbfs
<6>[ 27.014306] usbcore: registered new interface driver hub
<6>[ 27.050902] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
<6>[ 27.073691] usbcore: registered new device driver usb
<6>[ 27.105311] Linux video capture interface: v2.00
<7>[ 27.133379] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
<7>[ 27.133384] ohci_hcd: block sizes: ed 64 td 64
<6>[ 27.136391] USB Universal Host Controller Interface driver v3.0
<6>[ 27.229568] ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[17] MMIO=[e2020000-e20207ff] Max Packet=[2048] IR/IT contexts=[4/6]
<6>[ 27.261581] agpgart: Detected SiS chipset - id:1608
<7>[ 27.288172] ehci_hcd: block sizes: qh 128 qtd 96 itd 192 sitd 96
<6>[ 27.303726] agpgart: AGP aperture is 128M @ 0xd0000000
<6>[ 27.324070] hdc: ATAPI 16X DVD-ROM drive, 512kB Cache, UDMA(33)
<6>[ 27.345841] ACPI: PCI Interrupt 0000:00:04.0[A] -> GSI 19 (level, low) -> IRQ 18
<6>[ 27.364215] 0000:00:04.0: Unknown PHY transceiver found at address 0.
<6>[ 27.381688] Uniform CD-ROM driver Revision: 3.20
<6>[ 27.400492] 0000:00:04.0: Realtek RTL8201 PHY transceiver found at address 1.
<6>[ 27.424810] saa7130/34: v4l2 driver version 0.2.14 loaded
<6>[ 27.442837] 0000:00:04.0: Unknown PHY transceiver found at address 2.
<6>[ 27.462589] 0000:00:04.0: Unknown PHY transceiver found at address 3.
<6>[ 27.480102] hdd: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
<6>[ 27.498391] 0000:00:04.0: Unknown PHY transceiver found at address 4.
<6>[ 27.516848] 0000:00:04.0: Unknown PHY transceiver found at address 5.
<6>[ 27.542732] 0000:00:04.0: Unknown PHY transceiver found at address 6.
<6>[ 27.560964] 0000:00:04.0: Unknown PHY transceiver found at address 7.
<6>[ 27.578869] 0000:00:04.0: Unknown PHY transceiver found at address 8.
<6>[ 27.596762] 0000:00:04.0: Unknown PHY transceiver found at address 9.
<6>[ 27.616704] 0000:00:04.0: Unknown PHY transceiver found at address 10.
<6>[ 27.634504] 0000:00:04.0: Unknown PHY transceiver found at address 11.
<6>[ 27.651702] 0000:00:04.0: Unknown PHY transceiver found at address 12.
<6>[ 27.704083] 0000:00:04.0: Unknown PHY transceiver found at address 13.
<6>[ 27.720734] 0000:00:04.0: Unknown PHY transceiver found at address 14.
<6>[ 27.737118] 0000:00:04.0: Unknown PHY transceiver found at address 15.
<6>[ 27.753185] 0000:00:04.0: Unknown PHY transceiver found at address 16.
<6>[ 27.768970] 0000:00:04.0: Unknown PHY transceiver found at address 17.
<6>[ 27.784510] 0000:00:04.0: Unknown PHY transceiver found at address 18.
<6>[ 27.799790] 0000:00:04.0: Unknown PHY transceiver found at address 19.
<6>[ 27.814879] 0000:00:04.0: Unknown PHY transceiver found at address 20.
<6>[ 27.829800] 0000:00:04.0: Unknown PHY transceiver found at address 21.
<6>[ 27.844565] 0000:00:04.0: Unknown PHY transceiver found at address 22.
<6>[ 27.859231] 0000:00:04.0: Unknown PHY transceiver found at address 23.
<6>[ 27.873651] 0000:00:04.0: Unknown PHY transceiver found at address 24.
<6>[ 27.887825] 0000:00:04.0: Unknown PHY transceiver found at address 25.
<6>[ 27.901995] 0000:00:04.0: Unknown PHY transceiver found at address 26.
<6>[ 27.916161] 0000:00:04.0: Unknown PHY transceiver found at address 27.
<6>[ 27.930315] 0000:00:04.0: Unknown PHY transceiver found at address 28.
<6>[ 27.944171] 0000:00:04.0: Unknown PHY transceiver found at address 29.
<6>[ 27.957830] 0000:00:04.0: Unknown PHY transceiver found at address 30.
<6>[ 27.971472] 0000:00:04.0: Unknown PHY transceiver found at address 31.
<6>[ 28.008127] 0000:00:04.0: Using transceiver found at address 1 as default
<6>[ 28.021973] eth0: SiS 900 PCI Fast Ethernet at 0xdc00, IRQ 18, 00:10:dc:c5:f1:83.
<6>[ 28.035056] ACPI: PCI Interrupt 0000:00:03.0[A] -> GSI 20 (level, low) -> IRQ 19
<6>[ 28.048115] ohci_hcd 0000:00:03.0: OHCI Host Controller
<6>[ 28.061139] ohci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 1
<7>[ 28.074419] ohci_hcd 0000:00:03.0: created debug files
<6>[ 28.074431] ohci_hcd 0000:00:03.0: irq 19, io mem 0xe2021000
<7>[ 28.141497] ohci_hcd 0000:00:03.0: OHCI controller state
<7>[ 28.141501] ohci_hcd 0000:00:03.0: OHCI 1.0, NO legacy support registers
<7>[ 28.141505] ohci_hcd 0000:00:03.0: control 0x083 HCFS=operational CBSR=3
<7>[ 28.141508] ohci_hcd 0000:00:03.0: cmdstatus 0x00000 SOC=0
<7>[ 28.141511] ohci_hcd 0000:00:03.0: intrstatus 0x00000044 RHSC SF
<7>[ 28.141514] ohci_hcd 0000:00:03.0: intrenable 0x8000000a MIE RD WDH
<7>[ 28.141520] ohci_hcd 0000:00:03.0: hcca frame #0003
<7>[ 28.141524] ohci_hcd 0000:00:03.0: roothub.a 01001202 POTPGT=1 NOCP NPS NDP=2(2)
<7>[ 28.141528] ohci_hcd 0000:00:03.0: roothub.b 00000000 PPCM=0000 DR=0000
<7>[ 28.141531] ohci_hcd 0000:00:03.0: roothub.status 00008000 DRWE
<7>[ 28.141536] ohci_hcd 0000:00:03.0: roothub.portstatus [0] 0x00010301 CSC LSDA PPS CCS
<7>[ 28.141539] ohci_hcd 0000:00:03.0: roothub.portstatus [1] 0x00000100 PPS
<7>[ 28.141558] usb usb1: default language 0x0409
<7>[ 28.141566] usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
<6>[ 28.141568] usb usb1: Product: OHCI Host Controller
<6>[ 28.154592] usb usb1: Manufacturer: Linux 2.6.23-rc6-speedy ohci_hcd
<6>[ 28.167811] usb usb1: SerialNumber: 0000:00:03.0
<7>[ 28.180985] usb usb1: uevent
<7>[ 28.181151] usb usb1: usb_probe_device
<6>[ 28.182381] usb usb1: configuration #1 chosen from 1 choice
<7>[ 28.195604] usb usb1: adding 1-0:1.0 (config #1, interface 0)
<7>[ 28.195620] usb 1-0:1.0: uevent
<7>[ 28.195623] usb 1-0:1.0: uevent
<7>[ 28.195773] hub 1-0:1.0: usb_probe_interface
<7>[ 28.195776] hub 1-0:1.0: usb_probe_interface - got id
<6>[ 28.195779] hub 1-0:1.0: USB hub found
<6>[ 28.208829] hub 1-0:1.0: 2 ports detected
<7>[ 28.221712] hub 1-0:1.0: standalone hub
<7>[ 28.221715] hub 1-0:1.0: no power switching (usb 1.0)
<7>[ 28.221717] hub 1-0:1.0: no over-current protection
<7>[ 28.221719] hub 1-0:1.0: power on to power good time: 2ms
<7>[ 28.221725] hub 1-0:1.0: local power source is good
<7>[ 28.221727] hub 1-0:1.0: trying to enable port power on non-switchable hub
<7>[ 28.323442] hub 1-0:1.0: state 7 ports 2 chg 0000 evt 0000
<7>[ 28.323768] ohci_hcd 0000:00:03.0: GetStatus roothub.portstatus [0] = 0x00010301 CSC LSDA PPS CCS
<7>[ 28.323776] hub 1-0:1.0: port 1, status 0301, change 0001, 1.5 Mb/s
<6>[ 28.323836] ACPI: PCI Interrupt 0000:00:07.0[A] -> GSI 18 (level, low) -> IRQ 20
<6>[ 28.337023] uhci_hcd 0000:00:07.0: UHCI Host Controller
<6>[ 28.350241] uhci_hcd 0000:00:07.0: new USB bus registered, assigned bus number 2
<6>[ 28.363354] uhci_hcd 0000:00:07.0: detected 2 ports
<7>[ 28.376317] uhci_hcd 0000:00:07.0: uhci_check_and_reset_hc: cmd = 0x0000
<7>[ 28.376319] uhci_hcd 0000:00:07.0: Performing full reset
<6>[ 28.376340] uhci_hcd 0000:00:07.0: irq 20, io base 0x0000e000
<7>[ 28.389420] usb usb2: default language 0x0409
<7>[ 28.389428] usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
<6>[ 28.389431] usb usb2: Product: UHCI Host Controller
<6>[ 28.402470] usb usb2: Manufacturer: Linux 2.6.23-rc6-speedy uhci_hcd
<6>[ 28.415574] usb usb2: SerialNumber: 0000:00:07.0
<7>[ 28.428745] usb usb2: uevent
<7>[ 28.428913] usb usb2: usb_probe_device
<6>[ 28.429082] usb usb2: configuration #1 chosen from 1 choice
<7>[ 28.442373] usb usb2: adding 2-0:1.0 (config #1, interface 0)
<7>[ 28.442389] usb 2-0:1.0: uevent
<7>[ 28.442392] usb 2-0:1.0: uevent
<7>[ 28.442544] hub 2-0:1.0: usb_probe_interface
<7>[ 28.442547] hub 2-0:1.0: usb_probe_interface - got id
<6>[ 28.442550] hub 2-0:1.0: USB hub found
<6>[ 28.455767] hub 2-0:1.0: 2 ports detected
<7>[ 28.468960] hub 2-0:1.0: standalone hub
<7>[ 28.468963] hub 2-0:1.0: no power switching (usb 1.0)
<7>[ 28.468964] hub 2-0:1.0: individual port over-current protection
<7>[ 28.468967] hub 2-0:1.0: power on to power good time: 2ms
<7>[ 28.468971] hub 2-0:1.0: local power source is good
<7>[ 28.468974] hub 2-0:1.0: trying to enable port power on non-switchable hub
<7>[ 28.472040] hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
<7>[ 28.543357] ohci_hcd 0000:00:03.0: GetStatus roothub.portstatus [0] = 0x00100303 PRSC LSDA PPS PES CCS
<7>[ 28.552385] ieee1394: Host added: ID:BUS[0-00:1023] GUID[000010dc001ecc82]
<6>[ 28.571693] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
<6>[ 28.584884] sis96x_smbus 0000:00:02.1: SiS96x SMBus base address: 0x10c0
<6>[ 28.600358] usb 1-1: new low speed USB device using ohci_hcd and address 2
<6>[ 28.616245] ACPI: PCI Interrupt 0000:00:03.3[D] -> GSI 23 (level, low) -> IRQ 21
<6>[ 28.632262] ehci_hcd 0000:00:03.3: EHCI Host Controller
<6>[ 28.652269] ehci_hcd 0000:00:03.3: new USB bus registered, assigned bus number 3
<7>[ 28.665208] ehci_hcd 0000:00:03.3: reset hcs_params 0x103206 dbg=1 cc=3 pcc=2 ordered !ppc ports=6
<7>[ 28.665212] ehci_hcd 0000:00:03.3: reset hcc_params 7070 thresh 7 uframes 1024
<7>[ 28.665254] PCI: cache line size of 128 is not supported by device 0000:00:03.3
<7>[ 28.665258] ehci_hcd 0000:00:03.3: supports USB remote wakeup
<6>[ 28.665268] ehci_hcd 0000:00:03.3: irq 21, io mem 0xe2024000
<7>[ 28.684000] ohci_hcd 0000:00:03.0: GetStatus roothub.portstatus [0] = 0x00100303 PRSC LSDA PPS PES CCS
<7>[ 28.684018] ehci_hcd 0000:00:03.3: reset command 080002 (park)=0 ithresh=8 period=1024 Reset HALT
<7>[ 28.684025] ehci_hcd 0000:00:03.3: init command 010001 (park)=0 ithresh=1 period=1024 RUN
<6>[ 28.684030] ehci_hcd 0000:00:03.3: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
<7>[ 28.713688] usb usb3: default language 0x0409
<7>[ 28.713699] usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1
<6>[ 28.713702] usb usb3: Product: EHCI Host Controller
<6>[ 28.726712] usb usb3: Manufacturer: Linux 2.6.23-rc6-speedy ehci_hcd
<6>[ 28.739792] usb usb3: SerialNumber: 0000:00:03.3
<7>[ 28.752739] ohci_hcd 0000:00:03.0: urb c5ead340 path 1 ep0out 5ec20000 cc 5 --> status -62
<7>[ 28.752777] usb usb3: uevent
<7>[ 28.752981] usb usb3: usb_probe_device
<6>[ 28.753149] usb usb3: configuration #1 chosen from 1 choice
<7>[ 28.765850] usb usb3: adding 3-0:1.0 (config #1, interface 0)
<7>[ 28.765866] usb 3-0:1.0: uevent
<7>[ 28.765870] usb 3-0:1.0: uevent
<7>[ 28.766029] hub 3-0:1.0: usb_probe_interface
<7>[ 28.766032] hub 3-0:1.0: usb_probe_interface - got id
<6>[ 28.766035] hub 3-0:1.0: USB hub found
<6>[ 28.778320] hub 3-0:1.0: 6 ports detected
<7>[ 28.790546] hub 3-0:1.0: standalone hub
<7>[ 28.790548] hub 3-0:1.0: no power switching (usb 1.0)
<7>[ 28.790550] hub 3-0:1.0: individual port over-current protection
<7>[ 28.790552] hub 3-0:1.0: Single TT
<7>[ 28.790554] hub 3-0:1.0: TT requires at most 8 FS bit times (666 ns)
<7>[ 28.790556] hub 3-0:1.0: power on to power good time: 20ms
<7>[ 28.790561] hub 3-0:1.0: local power source is good
<7>[ 28.790564] hub 3-0:1.0: trying to enable port power on non-switchable hub
<6>[ 28.891611] ACPI: PCI Interrupt 0000:00:02.7[C] -> GSI 18 (level, low) -> IRQ 20
<7>[ 28.957103] ohci_hcd 0000:00:03.0: urb c5ead340 path 1 ep0out 5ec20000 cc 5 --> status -62
<3>[ 29.166906] usb 1-1: device not accepting address 2, error -62
<6>[ 29.219108] intel8x0_measure_ac97_clock: measured 52223 usecs
<6>[ 29.231404] intel8x0: clocking to 48000
<7>[ 29.243556] ohci_hcd 0000:00:03.0: GetStatus roothub.portstatus [0] = 0x00030300 PESC CSC LSDA PPS
<7>[ 29.243568] hub 2-0:1.0: state 7 ports 2 chg 0000 evt 0006
<7>[ 29.243583] uhci_hcd 0000:00:07.0: port 1 portsc 008a,00
<7>[ 29.243591] hub 2-0:1.0: port 1, status 0100, change 0003, 12 Mb/s
<6>[ 29.271859] ACPI: PCI Interrupt 0000:00:08.0[A] -> GSI 19 (level, low) -> IRQ 18
<6>[ 29.284362] saa7134[0]: found at 0000:00:08.0, rev: 1, irq: 18, latency: 32, mmio: 0xe2027000
<6>[ 29.315863] saa7134[0]: subsystem: 16be:0003, board: Medion 7134 [card=12,autodetected]
<6>[ 29.331867] saa7134[0]: board init: gpio is 0
<7>[ 29.379062] hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x100
<7>[ 29.379072] uhci_hcd 0000:00:07.0: port 2 portsc 009b,00
<7>[ 29.379081] hub 2-0:1.0: port 2, status 0101, change 0003, 12 Mb/s
<6>[ 29.487726] saa7134[0]: i2c eeprom 00: be 16 03 00 08 20 1c 55 43 43 a9 1c 55 43 43 a9
<6>[ 29.500640] saa7134[0]: i2c eeprom 10: ff ff ff ff 15 00 0e 01 0c c0 08 00 00 00 00 00
<7>[ 29.513424] hub 2-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x101
<6>[ 29.513439] saa7134[0]: i2c eeprom 20: 00 00 00 e3 ff ff ff ff ff ff ff ff ff ff ff ff
<6>[ 29.526287] saa7134[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
<6>[ 29.539226] saa7134[0]: i2c eeprom 40: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
<6>[ 29.552152] saa7134[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
<6>[ 29.567181] saa7134[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
<6>[ 29.580131] saa7134[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
<6>[ 29.610960] saa7134[0] Tuner type is 38
<6>[ 29.623745] usb 2-2: new full speed USB device using uhci_hcd and address 2
<6>[ 29.699660] tuner 1-0043: chip found @ 0x86 (saa7134[0])
<6>[ 29.713053] tda9887 1-0043: tda988[5/6/7] found @ 0x43 (tuner)
<4>[ 29.738912] tuner 1-0060: All bytes are equal. It is not a TEA5767
<6>[ 29.752722] tuner 1-0060: chip found @ 0xc0 (saa7134[0])
<6>[ 29.766658] tuner 1-0060: type set to 38 (Philips PAL/SECAM multi (FM1216ME MK3))
<6>[ 29.780914] tuner 1-0060: type set to 38 (Philips PAL/SECAM multi (FM1216ME MK3))
<6>[ 29.800731] saa7134[0]: registered device video0 [v4l2]
<6>[ 29.815177] usb 2-2: not running at top speed; connect to a high speed hub
<6>[ 29.830150] saa7134[0]: registered device vbi0
<6>[ 29.845271] saa7134[0]: registered device radio0
<7>[ 29.860180] usb 2-2: new device strings: Mfr=0, Product=0, SerialNumber=0
<7>[ 29.860206] usb 2-2: uevent
<7>[ 29.860382] usb 2-2: usb_probe_device
<6>[ 29.860549] usb 2-2: configuration #1 chosen from 1 choice
<7>[ 29.877965] usb 2-2: adding 2-2:1.0 (config #1, interface 0)
<7>[ 29.877999] usb 2-2:1.0: uevent
<7>[ 29.878003] usb 2-2:1.0: uevent
<7>[ 29.878281] hub 2-2:1.0: usb_probe_interface
<7>[ 29.878285] hub 2-2:1.0: usb_probe_interface - got id
<6>[ 29.878287] hub 2-2:1.0: USB hub found
<6>[ 29.894949] hub 2-2:1.0: 2 ports detected
<7>[ 29.911259] hub 2-2:1.0: compound device; port removable status: FR
<7>[ 29.911262] hub 2-2:1.0: ganged power switching
<7>[ 29.911264] hub 2-2:1.0: global over-current protection
<7>[ 29.911267] hub 2-2:1.0: power on to power good time: 100ms
<6>[ 29.912470] ACPI: PCI Interrupt 0000:00:03.1[B] -> GSI 21 (level, low) -> IRQ 22
<7>[ 29.929246] hub 2-2:1.0: local power source is good
<7>[ 29.929249] hub 2-2:1.0: no over-current condition exists
<7>[ 29.929251] hub 2-2:1.0: enabling power on all ports
<6>[ 29.951861] ohci_hcd 0000:00:03.1: OHCI Host Controller
<6>[ 29.977427] ohci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 4
<7>[ 29.993578] ohci_hcd 0000:00:03.1: created debug files
<6>[ 29.993589] ohci_hcd 0000:00:03.1: irq 22, io mem 0xe2022000
<7>[ 30.031582] uhci_hcd 0000:00:07.0: reserve dev 2 ep81-INT, period 128, phase 0, 12 us
<7>[ 30.032042] hub 1-0:1.0: state 7 ports 2 chg 0000 evt 0002
<7>[ 30.032052] ohci_hcd 0000:00:03.0: GetStatus roothub.portstatus [0] = 0x00030300 PESC CSC LSDA PPS
<7>[ 30.032060] hub 1-0:1.0: port 1, status 0300, change 0003, 1.5 Mb/s
<7>[ 30.071577] ohci_hcd 0000:00:03.1: enabling initreset quirk
<7>[ 30.073577] ohci_hcd 0000:00:03.1: OHCI controller state
<7>[ 30.073581] ohci_hcd 0000:00:03.1: OHCI 1.0, NO legacy support registers
<7>[ 30.073585] ohci_hcd 0000:00:03.1: control 0x083 HCFS=operational CBSR=3
<7>[ 30.073588] ohci_hcd 0000:00:03.1: cmdstatus 0x00000 SOC=0
<7>[ 30.073591] ohci_hcd 0000:00:03.1: intrstatus 0x00000004 SF
<7>[ 30.073595] ohci_hcd 0000:00:03.1: intrenable 0x8000004a MIE RHSC RD WDH
<7>[ 30.073601] ohci_hcd 0000:00:03.1: hcca frame #0003
<7>[ 30.073605] ohci_hcd 0000:00:03.1: roothub.a 01001202 POTPGT=1 NOCP NPS NDP=2(2)
<7>[ 30.073609] ohci_hcd 0000:00:03.1: roothub.b 00000000 PPCM=0000 DR=0000
<7>[ 30.073613] ohci_hcd 0000:00:03.1: roothub.status 00008000 DRWE
<7>[ 30.073617] ohci_hcd 0000:00:03.1: roothub.portstatus [0] 0x00000100 PPS
<7>[ 30.073621] ohci_hcd 0000:00:03.1: roothub.portstatus [1] 0x00000100 PPS
<7>[ 30.073645] usb usb4: default language 0x0409
<7>[ 30.073653] usb usb4: new device strings: Mfr=3, Product=2, SerialNumber=1
<6>[ 30.073656] usb usb4: Product: OHCI Host Controller
<6>[ 30.090046] usb usb4: Manufacturer: Linux 2.6.23-rc6-speedy ohci_hcd
<6>[ 30.106677] usb usb4: SerialNumber: 0000:00:03.1
<7>[ 30.123266] usb usb4: uevent
<7>[ 30.123548] usb usb4: usb_probe_device
<6>[ 30.123725] usb usb4: configuration #1 chosen from 1 choice
<7>[ 30.140197] usb usb4: adding 4-0:1.0 (config #1, interface 0)
<7>[ 30.140213] usb 4-0:1.0: uevent
<7>[ 30.140216] usb 4-0:1.0: uevent
<7>[ 30.140369] hub 4-0:1.0: usb_probe_interface
<7>[ 30.140372] hub 4-0:1.0: usb_probe_interface - got id
<6>[ 30.140374] hub 4-0:1.0: USB hub found
<6>[ 30.156633] hub 4-0:1.0: 2 ports detected
<7>[ 30.172685] hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x300
<7>[ 30.172690] hub 3-0:1.0: state 7 ports 6 chg 0000 evt 0000
<7>[ 30.172698] ehci_hcd 0000:00:03.3: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
<7>[ 30.172705] hub 3-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
<7>[ 30.172710] hub 4-0:1.0: standalone hub
<7>[ 30.172712] hub 4-0:1.0: no power switching (usb 1.0)
<7>[ 30.172714] hub 4-0:1.0: no over-current protection
<7>[ 30.172716] hub 4-0:1.0: power on to power good time: 2ms
<7>[ 30.172721] hub 4-0:1.0: local power source is good
<7>[ 30.172723] hub 4-0:1.0: trying to enable port power on non-switchable hub
<6>[ 30.275988] ACPI: PCI Interrupt 0000:00:03.2[C] -> GSI 22 (level, low) -> IRQ 23
<6>[ 30.292418] ohci_hcd 0000:00:03.2: OHCI Host Controller
<7>[ 30.308749] hub 3-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
<7>[ 30.308759] ehci_hcd 0000:00:03.3: port 1 low speed --> companion
<6>[ 30.308993] ohci_hcd 0000:00:03.2: new USB bus registered, assigned bus number 5
<7>[ 30.325399] ohci_hcd 0000:00:03.2: created debug files
<6>[ 30.325409] ohci_hcd 0000:00:03.2: irq 23, io mem 0xe2023000
<7>[ 30.363488] ehci_hcd 0000:00:03.3: GetStatus port 1 status 003002 POWER OWNER sig=se0 CSC
<7>[ 30.363514] ehci_hcd 0000:00:03.3: GetStatus port 2 status 001803 POWER sig=j CSC CONNECT
<7>[ 30.363522] hub 3-0:1.0: port 2, status 0501, change 0001, 480 Mb/s
<7>[ 30.394700] ohci_hcd 0000:00:03.2: enabling initreset quirk
<7>[ 30.396699] ohci_hcd 0000:00:03.2: OHCI controller state
<7>[ 30.396703] ohci_hcd 0000:00:03.2: OHCI 1.0, NO legacy support registers
<7>[ 30.396708] ohci_hcd 0000:00:03.2: control 0x083 HCFS=operational CBSR=3
<7>[ 30.396711] ohci_hcd 0000:00:03.2: cmdstatus 0x00000 SOC=0
<7>[ 30.396714] ohci_hcd 0000:00:03.2: intrstatus 0x00000004 SF
<7>[ 30.396718] ohci_hcd 0000:00:03.2: intrenable 0x8000004a MIE RHSC RD WDH
<7>[ 30.396724] ohci_hcd 0000:00:03.2: hcca frame #0003
<7>[ 30.396728] ohci_hcd 0000:00:03.2: roothub.a 01001202 POTPGT=1 NOCP NPS NDP=2(2)
<7>[ 30.396732] ohci_hcd 0000:00:03.2: roothub.b 00000000 PPCM=0000 DR=0000
<7>[ 30.396736] ohci_hcd 0000:00:03.2: roothub.status 00008000 DRWE
<7>[ 30.396740] ohci_hcd 0000:00:03.2: roothub.portstatus [0] 0x00000100 PPS
<7>[ 30.396744] ohci_hcd 0000:00:03.2: roothub.portstatus [1] 0x00000100 PPS
<7>[ 30.396761] usb usb5: default language 0x0409
<7>[ 30.396769] usb usb5: new device strings: Mfr=3, Product=2, SerialNumber=1
<6>[ 30.396772] usb usb5: Product: OHCI Host Controller
<6>[ 30.413078] usb usb5: Manufacturer: Linux 2.6.23-rc6-speedy ohci_hcd
<6>[ 30.429490] usb usb5: SerialNumber: 0000:00:03.2
<7>[ 30.445857] usb usb5: uevent
<7>[ 30.446071] usb usb5: usb_probe_device
<6>[ 30.446244] usb usb5: configuration #1 chosen from 1 choice
<7>[ 30.462738] usb usb5: adding 5-0:1.0 (config #1, interface 0)
<7>[ 30.462755] usb 5-0:1.0: uevent
<7>[ 30.462758] usb 5-0:1.0: uevent
<7>[ 30.462930] hub 5-0:1.0: usb_probe_interface
<7>[ 30.462933] hub 5-0:1.0: usb_probe_interface - got id
<6>[ 30.462935] hub 5-0:1.0: USB hub found
<6>[ 30.479219] hub 5-0:1.0: 2 ports detected
<7>[ 30.495301] hub 3-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x501
<7>[ 30.495311] hub 5-0:1.0: standalone hub
<7>[ 30.495313] hub 5-0:1.0: no power switching (usb 1.0)
<7>[ 30.495315] hub 5-0:1.0: no over-current protection
<7>[ 30.495317] hub 5-0:1.0: power on to power good time: 2ms
<7>[ 30.495322] hub 5-0:1.0: local power source is good
<7>[ 30.495324] hub 5-0:1.0: trying to enable port power on non-switchable hub
<7>[ 30.550622] ehci_hcd 0000:00:03.3: port 2 full speed --> companion
<7>[ 30.550627] ehci_hcd 0000:00:03.3: GetStatus port 2 status 003801 POWER OWNER sig=j CONNECT
<7>[ 30.550653] hub 3-0:1.0: port 2 not reset yet, waiting 50ms
<6>[ 30.598987] ACPI: PCI Interrupt 0000:00:07.1[B] -> GSI 19 (level, low) -> IRQ 18
<6>[ 30.615394] uhci_hcd 0000:00:07.1: UHCI Host Controller
<6>[ 30.631777] uhci_hcd 0000:00:07.1: new USB bus registered, assigned bus number 6
<7>[ 30.648454] ehci_hcd 0000:00:03.3: GetStatus port 2 status 003002 POWER OWNER sig=se0 CSC
<7>[ 30.648479] hub 2-2:1.0: state 7 ports 2 chg 0000 evt 0002
<6>[ 30.648492] uhci_hcd 0000:00:07.1: detected 2 ports
<7>[ 30.665943] uhci_hcd 0000:00:07.1: uhci_check_and_reset_hc: cmd = 0x0000
<7>[ 30.665946] uhci_hcd 0000:00:07.1: Performing full reset
<6>[ 30.665968] uhci_hcd 0000:00:07.1: irq 18, io base 0x0000e400
<7>[ 30.683350] hub 2-2:1.0: port 1, status 0101, change 0001, 12 Mb/s
<7>[ 30.683402] usb usb6: default language 0x0409
<7>[ 30.683410] usb usb6: new device strings: Mfr=3, Product=2, SerialNumber=1
<6>[ 30.683412] usb usb6: Product: UHCI Host Controller
<6>[ 30.700809] usb usb6: Manufacturer: Linux 2.6.23-rc6-speedy uhci_hcd
<6>[ 30.718362] usb usb6: SerialNumber: 0000:00:07.1
<7>[ 30.734751] usb usb6: uevent
<7>[ 30.734946] usb usb6: usb_probe_device
<6>[ 30.735119] usb usb6: configuration #1 chosen from 1 choice
<7>[ 30.752644] usb usb6: adding 6-0:1.0 (config #1, interface 0)
<7>[ 30.752664] usb 6-0:1.0: uevent
<7>[ 30.752667] usb 6-0:1.0: uevent
<7>[ 30.752834] hub 6-0:1.0: usb_probe_interface
<7>[ 30.752837] hub 6-0:1.0: usb_probe_interface - got id
<6>[ 30.752840] hub 6-0:1.0: USB hub found
<6>[ 30.770263] hub 6-0:1.0: 2 ports detected
<7>[ 30.786439] hub 6-0:1.0: standalone hub
<7>[ 30.786442] hub 6-0:1.0: no power switching (usb 1.0)
<7>[ 30.786444] hub 6-0:1.0: individual port over-current protection
<7>[ 30.786446] hub 6-0:1.0: power on to power good time: 2ms
<7>[ 30.786450] hub 6-0:1.0: local power source is good
<7>[ 30.786453] hub 6-0:1.0: trying to enable port power on non-switchable hub
<7>[ 30.851623] hub 2-2:1.0: debounce: port 1: total 100ms stable 100ms status 0x101
<7>[ 30.867617] hub 2-2:1.0: port 1 not reset yet, waiting 10ms
<6>[ 30.887700] ACPI: PCI Interrupt 0000:00:07.2[C] -> GSI 16 (level, low) -> IRQ 16
<6>[ 30.905195] ehci_hcd 0000:00:07.2: EHCI Host Controller
<6>[ 30.921451] ehci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 7
<7>[ 30.937827] ehci_hcd 0000:00:07.2: reset hcs_params 0x2204 dbg=0 cc=2 pcc=2 ordered !ppc ports=4
<7>[ 30.937832] ehci_hcd 0000:00:07.2: reset hcc_params 6872 thresh 7 uframes 256/512/1024
<7>[ 30.937878] ehci_hcd 0000:00:07.2: MWI active
<7>[ 30.937881] ehci_hcd 0000:00:07.2: supports USB remote wakeup
<6>[ 30.937891] ehci_hcd 0000:00:07.2: irq 16, io mem 0xe2026000
<7>[ 30.954089] ehci_hcd 0000:00:07.2: reset command 080002 (park)=0 ithresh=8 period=1024 Reset HALT
<7>[ 30.954095] ehci_hcd 0000:00:07.2: init command 010009 (park)=0 ithresh=1 period=256 RUN
<6>[ 30.954099] ehci_hcd 0000:00:07.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
<7>[ 30.971361] usb 2-2: uhci_result_common: failed with status 440000
<6>[ 30.971380] usb 2-2.1: new full speed USB device using uhci_hcd and address 3
<7>[ 30.988908] usb usb7: default language 0x0409
<7>[ 30.988916] usb usb7: new device strings: Mfr=3, Product=2, SerialNumber=1
<6>[ 30.988918] usb usb7: Product: EHCI Host Controller
<7>[ 31.005179] usb 2-2.1: uhci_result_common: failed with status 440000
<6>[ 31.005196] usb usb7: Manufacturer: Linux 2.6.23-rc6-speedy ehci_hcd
<7>[ 31.021504] usb 2-2.1: uhci_result_common: failed with status 440000
<6>[ 31.021516] usb usb7: SerialNumber: 0000:00:07.2
<7>[ 31.037752] usb 2-2.1: uhci_result_common: failed with status 440000
<7>[ 31.037790] usb usb7: uevent
<7>[ 31.037997] usb usb7: usb_probe_device
<6>[ 31.038188] usb usb7: configuration #1 chosen from 1 choice
<7>[ 31.055498] usb 2-2: uhci_result_common: failed with status 440000
<3>[ 31.055525] hub 2-2:1.0: cannot reset port 1 (err = -71)
<7>[ 31.073016] hub 2-2:1.0: port 1 not enabled, trying reset again...
<7>[ 31.073029] usb usb7: adding 7-0:1.0 (config #1, interface 0)
<7>[ 31.073046] usb 7-0:1.0: uevent
<7>[ 31.073049] usb 7-0:1.0: uevent
<7>[ 31.073229] hub 7-0:1.0: usb_probe_interface
<7>[ 31.073232] hub 7-0:1.0: usb_probe_interface - got id
<6>[ 31.073234] hub 7-0:1.0: USB hub found
<7>[ 31.090526] usb 2-2: uhci_result_common: failed with status 440000
<3>[ 31.090543] hub 2-2:1.0: cannot reset port 1 (err = -71)
<7>[ 31.107960] hub 2-2:1.0: port 1 not enabled, trying reset again...
<6>[ 31.107983] hub 7-0:1.0: 4 ports detected
<7>[ 31.124978] usb 2-2: uhci_result_common: failed with status 440000
<3>[ 31.124989] hub 2-2:1.0: cannot reset port 1 (err = -71)
<7>[ 31.142136] hub 2-2:1.0: port 1 not enabled, trying reset again...
<7>[ 31.142142] hub 7-0:1.0: standalone hub
<7>[ 31.142144] hub 7-0:1.0: no power switching (usb 1.0)
<7>[ 31.142146] hub 7-0:1.0: individual port over-current protection
<7>[ 31.142148] hub 7-0:1.0: Single TT
<7>[ 31.142150] hub 7-0:1.0: TT requires at most 8 FS bit times (666 ns)
<7>[ 31.142152] hub 7-0:1.0: power on to power good time: 20ms
<7>[ 31.142156] hub 7-0:1.0: local power source is good
<7>[ 31.142159] hub 7-0:1.0: trying to enable port power on non-switchable hub
<7>[ 31.142522] usb 2-2: uhci_result_common: failed with status 440000
<3>[ 31.142533] hub 2-2:1.0: cannot reset port 1 (err = -71)
<7>[ 31.159509] hub 2-2:1.0: port 1 not enabled, trying reset again...
<7>[ 31.161515] usb 2-2: uhci_result_common: failed with status 440000
<3>[ 31.161525] hub 2-2:1.0: cannot reset port 1 (err = -71)
<7>[ 31.178576] hub 2-2:1.0: port 1 not enabled, trying reset again...
<3>[ 31.178579] hub 2-2:1.0: Cannot enable port 1. Maybe the USB cable is bad?
<7>[ 31.195505] usb 2-2: uhci_result_common: failed with status 440000
<3>[ 31.195515] hub 2-2:1.0: cannot disable port 1 (err = -71)
<7>[ 31.212499] usb 2-2: uhci_result_common: failed with status 440000
<3>[ 31.212509] hub 2-2:1.0: cannot reset port 1 (err = -71)
<7>[ 31.228606] hub 2-2:1.0: port 1 not enabled, trying reset again...
<7>[ 31.229493] usb 2-2: uhci_result_common: failed with status 440000
<3>[ 31.229503] hub 2-2:1.0: cannot reset port 1 (err = -71)
<7>[ 31.245406] hub 2-2:1.0: port 1 not enabled, trying reset again...
<7>[ 31.246494] usb 2-2: uhci_result_common: failed with status 440000
<3>[ 31.246518] hub 2-2:1.0: cannot reset port 1 (err = -71)
<7>[ 31.262262] hub 2-2:1.0: port 1 not enabled, trying reset again...
<7>[ 31.262483] usb 2-2: uhci_result_common: failed with status 440000
<3>[ 31.262493] hub 2-2:1.0: cannot reset port 1 (err = -71)
<7>[ 31.278094] usb 2-2: uhci_result_common: failed with status 440000
<7>[ 31.278098] hub 2-2:1.0: transfer --> -84
<7>[ 31.278106] hub 2-2:1.0: port 1 not enabled, trying reset again...
<7>[ 31.278482] usb 2-2: uhci_result_common: failed with status 440000
<3>[ 31.279269] hub 2-2:1.0: cannot reset port 1 (err = -71)
<7>[ 31.294804] hub 2-2:1.0: port 1 not enabled, trying reset again...
<3>[ 31.294807] hub 2-2:1.0: Cannot enable port 1. Maybe the USB cable is bad?
<7>[ 31.350464] usb 2-2: uhci_result_common: failed with status 440000
<3>[ 31.355200] hub 2-2:1.0: cannot disable port 1 (err = -71)
<7>[ 31.379454] usb 2-2: uhci_result_common: failed with status 440000
<3>[ 31.379480] hub 2-2:1.0: cannot reset port 1 (err = -71)
<3>[ 31.397903] saa7134[0]/dvb: frontend initialization failed
<7>[ 31.435173] hub 2-2:1.0: port 1 not enabled, trying reset again...
<7>[ 31.436436] usb 2-2: uhci_result_common: failed with status 440000
<3>[ 31.436833] hub 2-2:1.0: cannot reset port 1 (err = -71)
<7>[ 31.459142] hub 2-2:1.0: port 1 not enabled, trying reset again...
<7>[ 31.460426] usb 2-2: uhci_result_common: failed with status 440000
<3>[ 31.463160] hub 2-2:1.0: cannot reset port 1 (err = -71)
<7>[ 31.495128] hub 2-2:1.0: port 1 not enabled, trying reset again...
<7>[ 31.496415] usb 2-2: uhci_result_common: failed with status 440000
<3>[ 31.496435] hub 2-2:1.0: cannot reset port 1 (err = -71)
<7>[ 31.519120] hub 2-2:1.0: port 1 not enabled, trying reset again...
<7>[ 31.520409] usb 2-2: uhci_result_common: failed with status 440000
<3>[ 31.521857] hub 2-2:1.0: cannot reset port 1 (err = -71)
<7>[ 31.548720] hub 2-2:1.0: port 1 not enabled, trying reset again...
<3>[ 31.548725] hub 2-2:1.0: Cannot enable port 1. Maybe the USB cable is bad?
<7>[ 31.572391] usb 2-2: uhci_result_common: failed with status 440000
<3>[ 31.572955] hub 2-2:1.0: cannot disable port 1 (err = -71)
<7>[ 31.603380] usb 2-2: uhci_result_common: failed with status 440000
<3>[ 31.604766] hub 2-2:1.0: cannot reset port 1 (err = -71)
<7>[ 31.631183] hub 2-2:1.0: port 1 not enabled, trying reset again...
<7>[ 31.632373] usb 2-2: uhci_result_common: failed with status 440000
<3>[ 31.632936] hub 2-2:1.0: cannot reset port 1 (err = -71)
<7>[ 31.651099] hub 2-2:1.0: port 1 not enabled, trying reset again...
<7>[ 31.652361] usb 2-2: uhci_result_common: failed with status 440000
<7>[ 31.653366] usb 2-2: uhci_result_common: failed with status 440000
<7>[ 31.653375] hub 2-2:1.0: transfer --> -84
<3>[ 31.654778] hub 2-2:1.0: cannot reset port 1 (err = -71)
<7>[ 31.671923] hub 2-2:1.0: port 1 not enabled, trying reset again...
<7>[ 31.673361] usb 2-2: uhci_result_common: failed with status 440000
<3>[ 31.673680] hub 2-2:1.0: cannot reset port 1 (err = -71)
<7>[ 31.688376] ohci_hcd 0000:00:03.2: auto-stop root hub
<7>[ 31.688392] hub 2-2:1.0: port 1 not enabled, trying reset again...
<7>[ 31.689348] usb 2-2: uhci_result_common: failed with status 440000
<3>[ 31.691103] hub 2-2:1.0: cannot reset port 1 (err = -71)
<7>[ 31.719453] hub 2-2:1.0: port 1 not enabled, trying reset again...
<3>[ 31.719458] hub 2-2:1.0: Cannot enable port 1. Maybe the USB cable is bad?
<7>[ 31.752332] usb 2-2: uhci_result_common: failed with status 440000
<3>[ 31.753934] hub 2-2:1.0: cannot disable port 1 (err = -71)
<7>[ 31.776327] usb 2-2: uhci_result_common: failed with status 440000
<3>[ 31.779045] hub 2-2:1.0: cannot disable port 1 (err = -71)
<7>[ 31.800317] usb 2-2: uhci_result_common: failed with status 440000
<3>[ 31.803026] hub 2-2:1.0: hub_port_status failed (err = -71)
<7>[ 31.843028] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0002
<7>[ 31.843041] ohci_hcd 0000:00:03.1: GetStatus roothub.portstatus [0] = 0x00010101 CSC PPS CCS
<7>[ 31.843050] hub 4-0:1.0: port 1, status 0101, change 0001, 12 Mb/s
<7>[ 31.975032] hub 4-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x101
<7>[ 32.037239] usb 2-2: uhci_result_common: failed with status 440000
<7>[ 32.037249] hub 2-2:1.0: transfer --> -84
<7>[ 32.046947] ohci_hcd 0000:00:03.1: GetStatus roothub.portstatus [0] = 0x00100103 PRSC PPS PES CCS
<6>[ 32.103008] usb 4-1: new full speed USB device using ohci_hcd and address 2
<7>[ 32.186952] ohci_hcd 0000:00:03.1: GetStatus roothub.portstatus [0] = 0x00100103 PRSC PPS PES CCS
<6>[ 32.199585] Adding 27189972k swap on /dev/hdb11. Priority:-1 extents:1 across:27189972k
<7>[ 32.262915] usb 4-1: ep0 maxpacket = 8
<7>[ 32.273488] usb 4-1: default language 0x0409
<7>[ 32.282483] usb 4-1: new device strings: Mfr=1, Product=2, SerialNumber=3
<6>[ 32.282486] usb 4-1: Product: Medion Flash XL V3.0C
<6>[ 32.296567] usb 4-1: Manufacturer: MEDION
<6>[ 32.310483] usb 4-1: SerialNumber: 2003-02
<7>[ 32.324355] usb 4-1: uevent
<7>[ 32.324378] usb 4-1: usb_probe_device
<6>[ 32.324433] usb 4-1: configuration #1 chosen from 1 choice
<7>[ 32.342471] usb 4-1: adding 4-1:1.0 (config #1, interface 0)
<7>[ 32.342509] usb 4-1:1.0: uevent
<7>[ 32.342514] usb 4-1:1.0: uevent
<7>[ 32.345578] hub 3-0:1.0: state 7 ports 6 chg 0000 evt 0004
<7>[ 32.345587] hub 1-0:1.0: state 7 ports 2 chg 0000 evt 0002
<7>[ 32.345593] ohci_hcd 0000:00:03.0: GetStatus roothub.portstatus [0] = 0x00010301 CSC LSDA PPS CCS
<7>[ 32.345598] hub 1-0:1.0: port 1, status 0301, change 0001, 1.5 Mb/s
<7>[ 32.421115] usb 2-2: uhci_result_common: failed with status 440000
<7>[ 32.421126] hub 2-2:1.0: transfer --> -84
<7>[ 32.470855] hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
<4>[ 32.525197] fuse init (API version 7.8)
<7>[ 32.550802] ohci_hcd 0000:00:03.0: GetStatus roothub.portstatus [0] = 0x00100303 PRSC LSDA PPS PES CCS
<5>[ 32.586605] SCSI subsystem initialized
<6>[ 32.606910] usb 1-1: new low speed USB device using ohci_hcd and address 4
<6>[ 32.643288] Initializing USB Mass Storage driver...
<7>[ 32.694774] ohci_hcd 0000:00:03.0: GetStatus roothub.portstatus [0] = 0x00100303 PRSC LSDA PPS PES CCS
<7>[ 32.778183] usb 1-1: skipped 1 descriptor after interface
<7>[ 32.781176] usb 1-1: default language 0x0409
<7>[ 32.784178] usb 1-1: new device strings: Mfr=0, Product=2, SerialNumber=0
<6>[ 32.784181] usb 1-1: Product: USB Optical Mouse
<7>[ 32.798182] usb 1-1: uevent
<7>[ 32.798700] usb 1-1: usb_probe_device
<6>[ 32.798948] usb 1-1: configuration #1 chosen from 1 choice
<7>[ 32.812948] usb 2-2: uhci_result_common: failed with status 440000
<7>[ 32.812955] hub 2-2:1.0: transfer --> -84
<7>[ 32.814729] usb 1-1: adding 1-1:1.0 (config #1, interface 0)
<7>[ 32.814767] usb 1-1:1.0: uevent
<7>[ 32.814771] usb 1-1:1.0: uevent
<7>[ 32.815332] usb-storage 4-1:1.0: usb_probe_interface
<7>[ 32.815339] usb-storage 4-1:1.0: usb_probe_interface - got id
<7>[ 32.815395] hub 5-0:1.0: state 7 ports 2 chg 0000 evt 0000
<7>[ 32.815408] hub 2-2:1.0: state 7 ports 2 chg 0000 evt 0002
<6>[ 32.815469] scsi0 : SCSI emulation for USB Mass Storage devices
<7>[ 32.830379] usb 2-2: uhci_result_common: failed with status 440000
<3>[ 32.830621] hub 2-2:1.0: hub_port_status failed (err = -71)
<7>[ 32.845721] hub 6-0:1.0: state 7 ports 2 chg 0000 evt 0006
<7>[ 32.845729] uhci_hcd 0000:00:07.1: port 1 portsc 008a,00
<7>[ 32.845740] hub 6-0:1.0: port 1, status 0100, change 0003, 12 Mb/s
<6>[ 32.845777] usbcore: registered new interface driver usb-storage
<6>[ 32.859878] USB Mass Storage support registered.
<7>[ 32.874741] usb-storage: device found at 2
<7>[ 32.874745] usb-storage: waiting for device to settle before scanning
<7>[ 32.970663] hub 6-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x100
<7>[ 32.970672] uhci_hcd 0000:00:07.1: port 2 portsc 008a,00
<7>[ 32.970681] hub 6-0:1.0: port 2, status 0100, change 0003, 12 Mb/s
<7>[ 33.098622] hub 6-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x100
<7>[ 33.098630] hub 2-0:1.0: state 7 ports 2 chg 0000 evt 0004
<7>[ 33.098636] uhci_hcd 0000:00:07.0: port 2 portsc 009a,00
<7>[ 33.098644] hub 2-0:1.0: port 2, status 0100, change 0003, 12 Mb/s
<6>[ 33.098648] usb 2-2: USB disconnect, address 2
<7>[ 33.112597] usb 2-2: unregistering device
<7>[ 33.112600] usb 2-2: usb_disable_device nuking all URBs
<7>[ 33.112610] uhci_hcd 0000:00:07.0: shutdown urb f7d8f2c0 pipe 40408280 ep1in-intr
<7>[ 33.113891] uhci_hcd 0000:00:07.0: release dev 2 ep81-INT, period 128, phase 0, 12 us
<7>[ 33.113901] usb 2-2: unregistering interface 2-2:1.0
<7>[ 33.114435] usb_endpoint usbdev2.2_ep81: ep_device_release called for usbdev2.2_ep81
<7>[ 33.114496] usb 2-2:1.0: uevent
<7>[ 33.114500] usb 2-2:1.0: uevent
<7>[ 33.114988] usb_endpoint usbdev2.2_ep00: ep_device_release called for usbdev2.2_ep00
<7>[ 33.115029] usb 2-2: uevent
<7>[ 33.241625] hub 2-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x100
<7>[ 33.241633] hub 7-0:1.0: state 7 ports 4 chg 0000 evt 0000
<7>[ 33.241645] ehci_hcd 0000:00:07.2: GetStatus port 2 status 001803 POWER sig=j CSC CONNECT
<7>[ 33.241651] hub 7-0:1.0: port 2, status 0501, change 0001, 480 Mb/s
<7>[ 33.369575] hub 7-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x501
<7>[ 33.426755] ehci_hcd 0000:00:07.2: port 2 high speed
<7>[ 33.426762] ehci_hcd 0000:00:07.2: GetStatus port 2 status 001005 POWER sig=se0 PE CONNECT
<6>[ 33.482503] usb 7-2: new high speed USB device using ehci_hcd and address 2
<7>[ 33.550733] ehci_hcd 0000:00:07.2: port 2 high speed
<7>[ 33.550739] ehci_hcd 0000:00:07.2: GetStatus port 2 status 001005 POWER sig=se0 PE CONNECT
<6>[ 33.617758] device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
<7>[ 33.633103] usb 7-2: new device strings: Mfr=0, Product=0, SerialNumber=0
<7>[ 33.633142] usb 7-2: uevent
<7>[ 33.633614] usb 7-2: usb_probe_device
<6>[ 33.633852] usb 7-2: configuration #1 chosen from 1 choice
<7>[ 33.649223] usb 7-2: adding 7-2:1.0 (config #1, interface 0)
<7>[ 33.649252] usb 7-2:1.0: uevent
<7>[ 33.649256] usb 7-2:1.0: uevent
<7>[ 33.649461] hub 7-2:1.0: usb_probe_interface
<7>[ 33.649465] hub 7-2:1.0: usb_probe_interface - got id
<6>[ 33.649467] hub 7-2:1.0: USB hub found
<6>[ 33.664718] hub 7-2:1.0: 2 ports detected
<7>[ 33.679720] hub 7-2:1.0: compound device; port removable status: FR
<7>[ 33.679723] hub 7-2:1.0: ganged power switching
<7>[ 33.679725] hub 7-2:1.0: global over-current protection
<7>[ 33.679727] hub 7-2:1.0: Single TT
<7>[ 33.679729] hub 7-2:1.0: TT requires at most 8 FS bit times (666 ns)
<7>[ 33.679731] hub 7-2:1.0: power on to power good time: 100ms
<7>[ 33.680035] hub 7-2:1.0: local power source is good
<7>[ 33.680038] hub 7-2:1.0: no over-current condition exists
<7>[ 33.680040] hub 7-2:1.0: enabling power on all ports
<7>[ 33.781438] usb 7-2: link qh256-0001/c5f29100 start 255 [1/0 us]
<7>[ 33.782453] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0002
<7>[ 33.782463] hub 1-0:1.0: state 7 ports 2 chg 0000 evt 0002
<7>[ 33.782468] hub 6-0:1.0: state 7 ports 2 chg 0000 evt 0000
<7>[ 33.782472] hub 7-2:1.0: state 7 ports 2 chg 0000 evt 0000
<7>[ 33.782694] hub 7-2:1.0: port 1, status 0101, change 0001, 12 Mb/s
<7>[ 33.909422] hub 7-2:1.0: debounce: port 1: total 100ms stable 100ms status 0x101
<6>[ 33.981410] usb 7-2.1: new high speed USB device using ehci_hcd and address 3
<7>[ 34.009402] hub 7-2:1.0: port 1 not reset yet, waiting 10ms
<7>[ 34.101637] usb 7-2.1: new device strings: Mfr=0, Product=0, SerialNumber=0
<7>[ 34.101674] usb 7-2.1: uevent
<7>[ 34.102148] usb 7-2.1: usb_probe_device
<6>[ 34.102404] usb 7-2.1: configuration #1 chosen from 1 choice
<7>[ 34.117886] usb 7-2.1: adding 7-2.1:1.0 (config #1, interface 0)
<7>[ 34.117908] usb 7-2.1:1.0: uevent
<7>[ 34.117912] usb 7-2.1:1.0: uevent
<7>[ 34.118099] hub 7-2.1:1.0: usb_probe_interface
<7>[ 34.118103] hub 7-2.1:1.0: usb_probe_interface - got id
<6>[ 34.118105] hub 7-2.1:1.0: USB hub found
<6>[ 34.134328] hub 7-2.1:1.0: 4 ports detected
<7>[ 34.149464] hub 7-2.1:1.0: compound device; port removable status: FRRR
<7>[ 34.149466] hub 7-2.1:1.0: ganged power switching
<7>[ 34.149468] hub 7-2.1:1.0: global over-current protection
<7>[ 34.149923] hub 7-2.1:1.0: TT per port
<7>[ 34.149928] hub 7-2.1:1.0: TT requires at most 8 FS bit times (666 ns)
<7>[ 34.149930] hub 7-2.1:1.0: power on to power good time: 100ms
<7>[ 34.150124] hub 7-2.1:1.0: local power source is good
<7>[ 34.150127] hub 7-2.1:1.0: no over-current condition exists
<7>[ 34.150130] hub 7-2.1:1.0: enabling power on all ports
<7>[ 34.253267] usb 7-2.1: link qh256-0001/c5f29200 start 255 [1/0 us]
<7>[ 34.253871] hub 7-2:1.0: state 7 ports 2 chg 0000 evt 0002
<7>[ 34.253980] hub 7-2.1:1.0: state 7 ports 4 chg 0000 evt 0000
<7>[ 34.254483] hub 7-2.1:1.0: port 1, status 0101, change 0001, 12 Mb/s
<7>[ 34.381333] hub 7-2.1:1.0: debounce: port 1: total 100ms stable 100ms status 0x101
<7>[ 34.414220] usb usb2: suspend_rh (auto-stop)
<7>[ 34.414239] usb usb6: suspend_rh (auto-stop)
<6>[ 34.453319] usb 7-2.1.1: new high speed USB device using ehci_hcd and address 4
<7>[ 34.489310] hub 7-2.1:1.0: port 1 not reset yet, waiting 10ms
<7>[ 34.601417] usb 7-2.1.1: skipped 1 descriptor after endpoint
<7>[ 34.608537] usb 7-2.1.1: default language 0x0409
<7>[ 34.647905] usb 7-2.1.1: new device strings: Mfr=1, Product=2, SerialNumber=3
<6>[ 34.647908] usb 7-2.1.1: Product: Flash Card Reader
<6>[ 34.663016] usb 7-2.1.1: Manufacturer: Generic
<6>[ 34.677774] usb 7-2.1.1: SerialNumber: 26020128B005
<7>[ 34.692456] usb 7-2.1.1: uevent
<7>[ 34.694184] usb 7-2.1.1: usb_probe_device
<6>[ 34.694499] usb 7-2.1.1: configuration #1 chosen from 1 choice
<7>[ 34.710146] usb 7-2.1.1: adding 7-2.1.1:1.0 (config #1, interface 0)
<7>[ 34.710187] usb 7-2.1.1:1.0: uevent
<7>[ 34.710191] usb 7-2.1.1:1.0: uevent
<7>[ 34.710452] usb-storage 7-2.1.1:1.0: usb_probe_interface
<7>[ 34.710458] usb-storage 7-2.1.1:1.0: usb_probe_interface - got id
<6>[ 34.710520] scsi1 : SCSI emulation for USB Mass Storage devices
<7>[ 34.725720] usb-storage: device found at 4
<7>[ 34.725723] usb-storage: waiting for device to settle before scanning
<7>[ 34.726521] hub 7-2.1:1.0: state 7 ports 4 chg 0000 evt 0002
<6>[ 34.735981] usbcore: registered new interface driver hiddev
<7>[ 34.759779] usbhid 1-1:1.0: usb_probe_interface
<7>[ 34.759784] usbhid 1-1:1.0: usb_probe_interface - got id
<6>[ 34.775517] input: USB Optical Mouse as /class/input/input3
<6>[ 34.794539] input: USB HID v1.11 Mouse [USB Optical Mouse] on usb-0000:00:03.0-1
<6>[ 34.809588] usbcore: registered new interface driver usbhid
<6>[ 34.838919] drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
<5>[ 37.930697] scsi 0:0:0:0: Direct-Access Medion Flash XL CF 3.0C PQ: 0 ANSI: 0 CCS
<5>[ 37.937694] scsi 0:0:0:1: Direct-Access Medion Flash XL MS 3.0C PQ: 0 ANSI: 0 CCS
<5>[ 37.945183] scsi 0:0:0:2: Direct-Access Medion Flash XL MMC/SD 3.0C PQ: 0 ANSI: 0 CCS
<5>[ 37.953175] scsi 0:0:0:3: Direct-Access Medion Flash XL SM 3.0C PQ: 0 ANSI: 0 CCS
<7>[ 37.962926] usb-storage: device scan complete
<5>[ 37.981197] sd 0:0:0:0: [sda] Attached SCSI removable disk
<5>[ 37.992234] sd 0:0:0:1: [sdb] Attached SCSI removable disk
<5>[ 38.003224] sd 0:0:0:2: [sdc] Attached SCSI removable disk
<5>[ 38.013694] sd 0:0:0:3: [sdd] Attached SCSI removable disk
<5>[ 38.048981] sd 0:0:0:0: Attached scsi generic sg0 type 0
<5>[ 38.050118] sd 0:0:0:1: Attached scsi generic sg1 type 0
<5>[ 38.051218] sd 0:0:0:2: Attached scsi generic sg2 type 0
<5>[ 38.052303] sd 0:0:0:3: Attached scsi generic sg3 type 0
<6>[ 38.409965] loop: module loaded
<6>[ 38.486212] kjournald starting. Commit interval 5 seconds
<6>[ 38.501848] EXT3 FS on hdb8, internal journal
<6>[ 38.517372] EXT3-fs: mounted filesystem with ordered data mode.
<6>[ 38.560004] kjournald starting. Commit interval 5 seconds
<6>[ 38.575769] EXT3 FS on hdb9, internal journal
<6>[ 38.591328] EXT3-fs: mounted filesystem with ordered data mode.
<6>[ 38.636545] kjournald starting. Commit interval 5 seconds
<6>[ 38.652348] EXT3 FS on hdb10, internal journal
<6>[ 38.667898] EXT3-fs: mounted filesystem with ordered data mode.
<7>[ 38.737498] ISO 9660 Extensions: Microsoft Joliet Level 3
<7>[ 38.784723] ISO 9660 Extensions: RRIP_1991A
<6>[ 38.823999] SGI XFS with ACLs, security attributes, realtime, no debug enabled
<6>[ 38.840268] SGI XFS Quota Management subsystem
<5>[ 38.940168] XFS mounting filesystem hdb12
<7>[ 39.051261] Ending clean XFS mount for filesystem: hdb12
<5>[ 39.732844] scsi 1:0:0:0: Direct-Access Generic Flash HS-CF 4.44 PQ: 0 ANSI: 0
<5>[ 39.753803] sd 1:0:0:0: [sde] Attached SCSI removable disk
<5>[ 39.770498] sd 1:0:0:0: Attached scsi generic sg4 type 0
<5>[ 39.790701] scsi 1:0:0:1: Direct-Access Generic Flash HS-COMBO 4.44 PQ: 0 ANSI: 0
<5>[ 39.857314] sd 1:0:0:1: [sdf] Attached SCSI removable disk
<5>[ 39.874312] sd 1:0:0:1: Attached scsi generic sg5 type 0
<7>[ 39.892592] usb-storage: device scan complete
Kernel logging (ksyslog) stopped.
Kernel log daemon terminating.
Boot logging started on /dev/tty1(/dev/console) at Sat Sep 15 18:50:53 2007
next prev parent reply other threads:[~2007-09-15 17:07 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
2007-09-14 21:28 2.6.23-rc6: usb 1-1: device not accepting address 2, error -62 Christian Volkmann
2007-09-15 10:48 ` Andrew Morton
2007-09-15 11:50 ` Christian Volkmann
2007-09-15 12:06 ` Christian Volkmann
2007-09-15 15:31 ` [linux-usb-devel] " Alan Stern
2007-09-15 17:07 ` Christian Volkmann [this message]
2007-09-15 19:55 ` Alan Stern
2007-09-15 16:56 ` Pete Zaitcev
2007-09-15 17:11 ` Christian Volkmann
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=46EC113A.4040309@cv-sv.de \
--to=haveaniceday@cv-sv.de \
--cc=akpm@linux-foundation.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-usb-devel@lists.sourceforge.net \
--cc=michal.k.k.piotrowski@gmail.com \
--cc=stern@rowland.harvard.edu \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.