From: "Denys" <denys@visp.net.lb>
To: linux-kernel@vger.kernel.org
Subject: SC1200 failure in 2.6.23 and 2.6.24-rc1-git10
Date: Thu, 1 Nov 2007 23:30:13 +0200 [thread overview]
Message-ID: <20071101213013.M54162@visp.net.lb> (raw)
Finally i got full DMESG with 1GB card till end. Seems not readable too.
Linux version 2.6.24-rc1-git10-embedded (root@homecore.visp.net.lb) (gcc
version 4.1.2 (Gentoo 4.1.2 p1.0.1)) #1 Thu Nov 1 23:12:53 EET 2007
BIOS-provided physical RAM map:
BIOS-e801: 0000000000000000 - 000000000009f000 (usable)
BIOS-e801: 0000000000100000 - 0000000004000000 (usable)
64MB LOWMEM available.
Zone PFN ranges:
DMA 0 -> 4096
Normal 4096 -> 16384
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0 -> 16384
DMI not present or invalid.
Allocating PCI resources starting at 10000000 (gap: 04000000:fc000000)
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
Kernel command line: console=ttyS0,38400n8
Initializing CPU#0
PID hash table entries: 256 (order: 8, 1024 bytes)
Detected 266.627 MHz processor.
Console: colour dummy device 80x25
console [ttyS0] enabled
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 62836k/65536k available (1020k kernel code, 2292k reserved, 317k
data, 112k init, 0k highmem)
virtual kernel memory layout:
fixmap : 0xffffb000 - 0xfffff000 ( 16 kB)
vmalloc : 0xc4800000 - 0xffff9000 ( 951 MB)
lowmem : 0xc0000000 - 0xc4000000 ( 64 MB)
.init : 0xc0252000 - 0xc026e000 ( 112 kB)
.data : 0xc01ff111 - 0xc024e6f4 ( 317 kB)
.text : 0xc0100000 - 0xc01ff111 (1020 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
SLUB: Genslabs=11, HWalign=32, Order=0-1, MinObjects=4, CPUs=1, Nodes=1
Calibrating delay using timer specific routine.. 534.41 BogoMIPS (lpj=1068836)
Mount-cache hash table entries: 512
Compat vDSO mapped to ffffe000.
CPU: NSC Unknown stepping 01
Checking 'hlt' instruction... OK.
Freeing SMP alternatives: 0k freed
net_namespace: 64 bytes
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfc3ad, last bus=0
PCI: Using configuration type 1
Setting up standard PCI resources
SCSI subsystem initialized
PCI: Probing PCI hardware
PCI: Device 0000:00:12.5 not found by BIOS
Time: tsc clocksource has been installed.
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
scx200: NatSemi SCx200 Driver
scx200: GPIO base 0xf400
scx200: Configuration Block base 0x9000
io scheduler noop registered (default)
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a NS16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a NS16550A
natsemi dp8381x driver, version 2.1, Sept 11, 2006
originally by Donald Becker <becker@scyld.com>
2.4.x kernel port by Jeff Garzik, Tjeerd Mulder
natsemi eth0: NatSemi DP8381[56] at 0x80000000 (0000:00:0e.0),
00:0d:b9:00:8a:30, IRQ 10, port TP.
scsi0 : sc1200
scsi1 : sc1200
ata1: PATA max UDMA/33 cmd 0x1f0 ctl 0x3f6 bmdma 0xfc00 irq 14
ata2: DUMMY
ata1.00: CFA: SanDisk SDCFH-1024, HDX 3.07, max MWDMA2
ata1.00: 2001888 sectors, multi 0: LBA
ata1.00: configured for MWDMA2
scsi 0:0:0:0: Direct-Access ATA SanDisk SDCFH-10 HDX PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 2001888 512-byte hardware sectors (1025 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
sd 0:0:0:0: [sda] 2001888 512-byte hardware sectors (1025 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
sda:<4>Clocksource tsc unstable (delta = -334501841 ns)
Time: pit clocksource has been installed.
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 cdb 0x0 data 4096 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata1.00: status: { DRDY }
ata1: soft resetting link
ata1.00: configured for MWDMA2
ata1: EH complete
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 cdb 0x0 data 4096 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata1.00: status: { DRDY }
ata1: soft resetting link
ata1.00: configured for MWDMA2
ata1: EH complete
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 cdb 0x0 data 4096 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata1.00: status: { DRDY }
ata1: soft resetting link
ata1.00: configured for MWDMA2
ata1: EH complete
ata1.00: limiting speed to MWDMA1:PIO4
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 cdb 0x0 data 4096 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata1.00: status: { DRDY }
ata1: soft resetting link
ata1.00: configured for MWDMA1
ata1: EH complete
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 cdb 0x0 data 4096 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata1.00: status: { DRDY }
ata1: soft resetting link
ata1.00: configured for MWDMA1
ata1: EH complete
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 cdb 0x0 data 4096 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata1.00: status: { DRDY }
ata1: soft resetting link
ata1.00: configured for MWDMA1
sd 0:0:0:0: [sda] Result: hostbyte=0x00 driverbyte=0x08
sd 0:0:0:0: [sda] Sense Key : 0xb [current] [descriptor]
Descriptor sense data with sense descriptors (in hex):
72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
00 00 00 00
sd 0:0:0:0: [sda] ASC=0x0 ASCQ=0x0
end_request: I/O error, dev sda, sector 0
Buffer I/O error on device sda, logical block 0
ata1: EH complete
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 cdb 0x0 data 4096 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata1.00: status: { DRDY }
ata1: soft resetting link
ata1.00: configured for MWDMA1
ata1: EH complete
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 cdb 0x0 data 4096 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata1.00: status: { DRDY }
ata1: soft resetting link
ata1.00: configured for MWDMA1
ata1: EH complete
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 cdb 0x0 data 4096 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata1.00: status: { DRDY }
ata1: soft resetting link
ata1.00: configured for MWDMA1
ata1: EH complete
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 cdb 0x0 data 4096 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata1.00: status: { DRDY }
ata1: soft resetting link
ata1.00: configured for MWDMA1
ata1: EH complete
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 cdb 0x0 data 4096 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata1.00: status: { DRDY }
ata1: soft resetting link
ata1.00: configured for MWDMA1
ata1: EH complete
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 cdb 0x0 data 4096 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata1.00: status: { DRDY }
ata1: soft resetting link
ata1.00: configured for MWDMA1
sd 0:0:0:0: [sda] Result: hostbyte=0x00 driverbyte=0x08
sd 0:0:0:0: [sda] Sense Key : 0xb [current] [descriptor]
Descriptor sense data with sense descriptors (in hex):
72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
00 00 00 00
sd 0:0:0:0: [sda] ASC=0x0 ASCQ=0x0
end_request: I/O error, dev sda, sector 0
Buffer I/O error on device sda, logical block 0
ata1: EH complete
unable to read partition table
sd 0:0:0:0: [sda] Attached SCSI removable disk
scx200_wdt: timer margin 60 seconds
cpuidle: using governor ladder
enabling scx200 high-res timer (1 MHz +0 ppm)
TCP cubic registered
Time: scx200_hrt clocksource has been installed.
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI Shortcut mode
VFS: Cannot open root device "<NULL>" or unknown-block(8,18)
Please append a correct "root=" boot option; here are the available
partitions:
0800 1000944 sda driver: sd
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-
block(8,18)
--
Denys Fedoryshchenko
Technical Manager
Virtual ISP S.A.L.
next reply other threads:[~2007-11-01 22:04 UTC|newest]
Thread overview: 25+ messages / expand[flat|nested] mbox.gz Atom feed top
2007-11-01 21:30 Denys [this message]
2007-11-07 6:15 ` SC1200 failure in 2.6.23 and 2.6.24-rc1-git10 Andrew Morton
2007-11-07 13:27 ` Denys Fedoryshchenko
2007-11-07 15:23 ` James Andrewartha
2007-11-07 16:06 ` Denys Fedoryshchenko
2007-11-07 19:12 ` Mark Lord
2007-11-07 21:22 ` Denys Fedoryshchenko
2007-11-07 22:31 ` Mark Lord
2007-11-07 22:54 ` Alan Cox
2007-11-07 21:36 ` Denys Fedoryshchenko
2007-11-07 23:20 ` Jeff Garzik
2007-11-07 23:24 ` Mark Lord
2007-11-07 23:49 ` Denys Fedoryshchenko
2007-11-08 0:01 ` Denys Fedoryshchenko
2007-11-08 0:30 ` Bartlomiej Zolnierkiewicz
2007-11-08 7:16 ` Denys Fedoryshchenko
2007-11-08 10:48 ` Alan Cox
2007-11-08 16:44 ` Denys Fedoryshchenko
2007-11-08 17:31 ` Jeff Garzik
2007-11-08 19:56 ` Denys Fedoryshchenko
2007-11-08 22:40 ` Alan Cox
2007-11-09 1:44 ` Tejun Heo
[not found] <fa.FFqM2AneKZLH2d3/UIeCMjE/RLE@ifi.uio.no>
2007-11-08 1:41 ` Robert Hancock
2007-11-08 7:01 ` Denys Fedoryshchenko
-- strict thread matches above, loose matches on Subject: below --
2007-11-01 21:25 Denys
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20071101213013.M54162@visp.net.lb \
--to=denys@visp.net.lb \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.