[PATCH 2/2] ide-{floppy,tape}: remove debug code for dumping identify data

[PATCH 2/2] ide-{floppy,tape}: remove debug code for dumping identify data

[Bartlomiej Zolnierkiewicz]

IDE core supports dumping raw identify data in hdparm friendly format now
so verbose identify dumping in ide-{floppy,tape}.c device drivers (done iff
IDE{FLOPPY,TAPE}_DEBUG_INFO is defined to '1' and it is '0' by default)
is no longer nedeed.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
---
 drivers/ide/ide-floppy.c |   50 ---------------------------------------
 drivers/ide/ide-tape.c   |   59 -----------------------------------------------
 2 files changed, 109 deletions(-)

Index: b/drivers/ide/ide-floppy.c
===================================================================
--- a/drivers/ide/ide-floppy.c
+++ b/drivers/ide/ide-floppy.c
@@ -1658,7 +1658,6 @@ static int idefloppy_identify_device (id
 {
 	struct idefloppy_id_gcw gcw;
 #if IDEFLOPPY_DEBUG_INFO
-	u16 mask,i;
 	char buffer[80];
 #endif /* IDEFLOPPY_DEBUG_INFO */
 
@@ -1705,55 +1704,6 @@ static int idefloppy_identify_device (id
 		default: sprintf(buffer, "Reserved");break;
 	}
 	printk(KERN_INFO "Command Packet Size: %s\n", buffer);
-	printk(KERN_INFO "Model: %.40s\n",id->model);
-	printk(KERN_INFO "Firmware Revision: %.8s\n",id->fw_rev);
-	printk(KERN_INFO "Serial Number: %.20s\n",id->serial_no);
-	printk(KERN_INFO "Write buffer size(?): %d bytes\n",id->buf_size*512);
-	printk(KERN_INFO "DMA: %s",id->capability & 0x01 ? "Yes\n":"No\n");
-	printk(KERN_INFO "LBA: %s",id->capability & 0x02 ? "Yes\n":"No\n");
-	printk(KERN_INFO "IORDY can be disabled: %s",id->capability & 0x04 ? "Yes\n":"No\n");
-	printk(KERN_INFO "IORDY supported: %s",id->capability & 0x08 ? "Yes\n":"Unknown\n");
-	printk(KERN_INFO "ATAPI overlap supported: %s",id->capability & 0x20 ? "Yes\n":"No\n");
-	printk(KERN_INFO "PIO Cycle Timing Category: %d\n",id->tPIO);
-	printk(KERN_INFO "DMA Cycle Timing Category: %d\n",id->tDMA);
-	printk(KERN_INFO "Single Word DMA supported modes:\n");
-	for (i=0,mask=1;i<8;i++,mask=mask << 1) {
-		if (id->dma_1word & mask)
-			printk(KERN_INFO "   Mode %d%s\n", i,
-			(id->dma_1word & (mask << 8)) ? " (active)" : "");
-	}
-	printk(KERN_INFO "Multi Word DMA supported modes:\n");
-	for (i=0,mask=1;i<8;i++,mask=mask << 1) {
-		if (id->dma_mword & mask)
-			printk(KERN_INFO "   Mode %d%s\n", i,
-			(id->dma_mword & (mask << 8)) ? " (active)" : "");
-	}
-	if (id->field_valid & 0x0002) {
-		printk(KERN_INFO "Enhanced PIO Modes: %s\n",
-			id->eide_pio_modes & 1 ? "Mode 3":"None");
-		if (id->eide_dma_min == 0)
-			sprintf(buffer, "Not supported");
-		else
-			sprintf(buffer, "%d ns",id->eide_dma_min);
-		printk(KERN_INFO "Minimum Multi-word DMA cycle per word: %s\n", buffer);
-		if (id->eide_dma_time == 0)
-			sprintf(buffer, "Not supported");
-		else
-			sprintf(buffer, "%d ns",id->eide_dma_time);
-		printk(KERN_INFO "Manufacturer\'s Recommended Multi-word cycle: %s\n", buffer);
-		if (id->eide_pio == 0)
-			sprintf(buffer, "Not supported");
-		else
-			sprintf(buffer, "%d ns",id->eide_pio);
-		printk(KERN_INFO "Minimum PIO cycle without IORDY: %s\n",
-			buffer);
-		if (id->eide_pio_iordy == 0)
-			sprintf(buffer, "Not supported");
-		else
-			sprintf(buffer, "%d ns",id->eide_pio_iordy);
-		printk(KERN_INFO "Minimum PIO cycle with IORDY: %s\n", buffer);
-	} else
-		printk(KERN_INFO "According to the device, fields 64-70 are not valid.\n");
 #endif /* IDEFLOPPY_DEBUG_INFO */
 
 	if (gcw.protocol != 2)
Index: b/drivers/ide/ide-tape.c
===================================================================
--- a/drivers/ide/ide-tape.c
+++ b/drivers/ide/ide-tape.c
@@ -4291,9 +4291,6 @@ static int idetape_identify_device (ide_
 {
 	struct idetape_id_gcw gcw;
 	struct hd_driveid *id = drive->id;
-#if IDETAPE_DEBUG_INFO
-	unsigned short mask,i;
-#endif /* IDETAPE_DEBUG_INFO */
 
 	if (drive->id_read == 0)
 		return 1;
@@ -4333,62 +4330,6 @@ static int idetape_identify_device (ide_
 		case 1: printk("16 bytes\n");break;
 		default: printk("Reserved\n");break;
 	}
-	printk(KERN_INFO "ide-tape: Model: %.40s\n",id->model);
-	printk(KERN_INFO "ide-tape: Firmware Revision: %.8s\n",id->fw_rev);
-	printk(KERN_INFO "ide-tape: Serial Number: %.20s\n",id->serial_no);
-	printk(KERN_INFO "ide-tape: Write buffer size: %d bytes\n",id->buf_size*512);
-	printk(KERN_INFO "ide-tape: DMA: %s",id->capability & 0x01 ? "Yes\n":"No\n");
-	printk(KERN_INFO "ide-tape: LBA: %s",id->capability & 0x02 ? "Yes\n":"No\n");
-	printk(KERN_INFO "ide-tape: IORDY can be disabled: %s",id->capability & 0x04 ? "Yes\n":"No\n");
-	printk(KERN_INFO "ide-tape: IORDY supported: %s",id->capability & 0x08 ? "Yes\n":"Unknown\n");
-	printk(KERN_INFO "ide-tape: ATAPI overlap supported: %s",id->capability & 0x20 ? "Yes\n":"No\n");
-	printk(KERN_INFO "ide-tape: PIO Cycle Timing Category: %d\n",id->tPIO);
-	printk(KERN_INFO "ide-tape: DMA Cycle Timing Category: %d\n",id->tDMA);
-	printk(KERN_INFO "ide-tape: Single Word DMA supported modes: ");
-	for (i=0,mask=1;i<8;i++,mask=mask << 1) {
-		if (id->dma_1word & mask)
-			printk("%d ",i);
-		if (id->dma_1word & (mask << 8))
-			printk("(active) ");
-	}
-	printk("\n");
-	printk(KERN_INFO "ide-tape: Multi Word DMA supported modes: ");
-	for (i=0,mask=1;i<8;i++,mask=mask << 1) {
-		if (id->dma_mword & mask)
-			printk("%d ",i);
-		if (id->dma_mword & (mask << 8))
-			printk("(active) ");
-	}
-	printk("\n");
-	if (id->field_valid & 0x0002) {
-		printk(KERN_INFO "ide-tape: Enhanced PIO Modes: %s\n",
-			id->eide_pio_modes & 1 ? "Mode 3":"None");
-		printk(KERN_INFO "ide-tape: Minimum Multi-word DMA cycle per word: ");
-		if (id->eide_dma_min == 0)
-			printk("Not supported\n");
-		else
-			printk("%d ns\n",id->eide_dma_min);
-
-		printk(KERN_INFO "ide-tape: Manufacturer\'s Recommended Multi-word cycle: ");
-		if (id->eide_dma_time == 0)
-			printk("Not supported\n");
-		else
-			printk("%d ns\n",id->eide_dma_time);
-
-		printk(KERN_INFO "ide-tape: Minimum PIO cycle without IORDY: ");
-		if (id->eide_pio == 0)
-			printk("Not supported\n");
-		else
-			printk("%d ns\n",id->eide_pio);
-
-		printk(KERN_INFO "ide-tape: Minimum PIO cycle with IORDY: ");
-		if (id->eide_pio_iordy == 0)
-			printk("Not supported\n");
-		else
-			printk("%d ns\n",id->eide_pio_iordy);
-		
-	} else
-		printk(KERN_INFO "ide-tape: According to the device, fields 64-70 are not valid.\n");
 #endif /* IDETAPE_DEBUG_INFO */
 
 	/* Check that we can support this device */