* [PATCH] sh: add support for sh7366 processor
@ 2008-02-08 8:31 Magnus Damm
0 siblings, 0 replies; only message in thread
From: Magnus Damm @ 2008-02-08 8:31 UTC (permalink / raw)
To: linux-sh
This patch adds sh7366 cpu supports. Just the most basic things like interrupt
controller, clocks and serial port are included at this point.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
---
arch/sh/Kconfig | 7 +
arch/sh/Kconfig.debug | 2
arch/sh/kernel/cpu/sh4/probe.c | 6 +
arch/sh/kernel/cpu/sh4a/Makefile | 2
arch/sh/kernel/cpu/sh4a/clock-sh7722.c | 10 +
arch/sh/kernel/cpu/sh4a/setup-sh7366.c | 177 ++++++++++++++++++++++++++++++++
arch/sh/kernel/setup.c | 2
drivers/serial/sh-sci.c | 2
drivers/serial/sh-sci.h | 8 +
include/asm-sh/cpu-sh4/freq.h | 4
include/asm-sh/processor.h | 2
11 files changed, 215 insertions(+), 7 deletions(-)
--- 0001/arch/sh/Kconfig
+++ work/arch/sh/Kconfig 2008-02-08 15:49:27.000000000 +0900
@@ -308,6 +308,13 @@ config CPU_SUBTYPE_SH7722
select ARCH_SPARSEMEM_ENABLE
select SYS_SUPPORTS_NUMA
+config CPU_SUBTYPE_SH7366
+ bool "Support SH7366 processor"
+ select CPU_SH4AL_DSP
+ select CPU_SHX2
+ select ARCH_SPARSEMEM_ENABLE
+ select SYS_SUPPORTS_NUMA
+
# SH-5 Processor Support
config CPU_SUBTYPE_SH5_101
--- 0001/arch/sh/Kconfig.debug
+++ work/arch/sh/Kconfig.debug 2008-02-08 15:49:27.000000000 +0900
@@ -30,7 +30,7 @@ config EARLY_SCIF_CONSOLE_PORT
hex
depends on EARLY_SCIF_CONSOLE
default "0xffe00000" if CPU_SUBTYPE_SH7780 || CPU_SUBTYPE_SH7763
- default "0xffe00000" if CPU_SUBTYPE_SH7722
+ default "0xffe00000" if CPU_SUBTYPE_SH7722 || CPU_SUBTYPE_SH7366
default "0xffea0000" if CPU_SUBTYPE_SH7785
default "0xfffe8000" if CPU_SUBTYPE_SH7203
default "0xfffe9800" if CPU_SUBTYPE_SH7206 || CPU_SUBTYPE_SH7263
--- 0001/arch/sh/kernel/cpu/sh4/probe.c
+++ work/arch/sh/kernel/cpu/sh4/probe.c 2008-02-08 15:49:27.000000000 +0900
@@ -132,6 +132,12 @@ int __init detect_cpu_and_cache_system(v
boot_cpu_data.dcache.ways = 4;
boot_cpu_data.flags |= CPU_HAS_LLSC;
}
+ else if (prr = 0x70) {
+ boot_cpu_data.type = CPU_SH7366;
+ boot_cpu_data.icache.ways = 4;
+ boot_cpu_data.dcache.ways = 4;
+ boot_cpu_data.flags |= CPU_HAS_LLSC;
+ }
break;
case 0x4000: /* 1st cut */
case 0x4001: /* 2nd cut */
--- 0001/arch/sh/kernel/cpu/sh4a/Makefile
+++ work/arch/sh/kernel/cpu/sh4a/Makefile 2008-02-08 15:53:22.000000000 +0900
@@ -9,6 +9,7 @@ obj-$(CONFIG_CPU_SUBTYPE_SH7780) += setu
obj-$(CONFIG_CPU_SUBTYPE_SH7785) += setup-sh7785.o
obj-$(CONFIG_CPU_SUBTYPE_SH7343) += setup-sh7343.o
obj-$(CONFIG_CPU_SUBTYPE_SH7722) += setup-sh7722.o
+obj-$(CONFIG_CPU_SUBTYPE_SH7366) += setup-sh7366.o
obj-$(CONFIG_CPU_SUBTYPE_SHX3) += setup-shx3.o
# SMP setup
@@ -21,6 +22,7 @@ clock-$(CONFIG_CPU_SUBTYPE_SH7780) := cl
clock-$(CONFIG_CPU_SUBTYPE_SH7785) := clock-sh7785.o
clock-$(CONFIG_CPU_SUBTYPE_SH7343) := clock-sh7343.o
clock-$(CONFIG_CPU_SUBTYPE_SH7722) := clock-sh7722.o
+clock-$(CONFIG_CPU_SUBTYPE_SH7366) := clock-sh7722.o
clock-$(CONFIG_CPU_SUBTYPE_SHX3) := clock-shx3.o
obj-y += $(clock-y)
--- 0001/arch/sh/kernel/cpu/sh4a/clock-sh7722.c
+++ work/arch/sh/kernel/cpu/sh4a/clock-sh7722.c 2008-02-08 15:57:53.000000000 +0900
@@ -1,7 +1,7 @@
/*
* arch/sh/kernel/cpu/sh4a/clock-sh7722.c
*
- * SH7722 support for the clock framework
+ * SH7722 & SH7366 support for the clock framework
*
* Copyright (c) 2006-2007 Nomad Global Solutions Inc
* Based on code for sh7343 by Paul Mundt
@@ -417,15 +417,19 @@ static int sh7722_siu_which(struct clk *
return 0;
if (!strcmp(clk->name, "siu_b_clk"))
return 1;
+#if defined(CONFIG_CPU_SUBTYPE_SH7722)
if (!strcmp(clk->name, "irda_clk"))
return 2;
+#endif
return -EINVAL;
}
static unsigned long sh7722_siu_regs[] = {
[0] = SCLKACR,
[1] = SCLKBCR,
+#if defined(CONFIG_CPU_SUBTYPE_SH7722)
[2] = IrDACLKCR,
+#endif
};
static int sh7722_siu_start_stop(struct clk *clk, int enable)
@@ -571,10 +575,12 @@ static struct clk sh7722_siu_b_clock = {
.ops = &sh7722_siu_clk_ops,
};
+#if defined(CONFIG_CPU_SUBTYPE_SH7722)
static struct clk sh7722_irda_clock = {
.name = "irda_clk",
.ops = &sh7722_siu_clk_ops,
};
+#endif
static struct clk sh7722_video_clock = {
.name = "video_clk",
@@ -588,7 +594,9 @@ static struct clk *sh7722_clocks[] = {
&sh7722_sdram_clock,
&sh7722_siu_a_clock,
&sh7722_siu_b_clock,
+#if defined(CONFIG_CPU_SUBTYPE_SH7722)
&sh7722_irda_clock,
+#endif
&sh7722_video_clock,
};
--- /dev/null
+++ work/arch/sh/kernel/cpu/sh4a/setup-sh7366.c 2008-02-08 17:06:50.000000000 +0900
@@ -0,0 +1,177 @@
+/*
+ * SH7366 Setup
+ *
+ * Copyright (C) 2008 Renesas Solutions
+ *
+ * Based on linux/arch/sh/kernel/cpu/sh4a/setup-sh7722.c
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License. See the file "COPYING" in the main directory of this archive
+ * for more details.
+ */
+#include <linux/platform_device.h>
+#include <linux/init.h>
+#include <linux/serial.h>
+#include <asm/sci.h>
+
+static struct plat_sci_port sci_platform_data[] = {
+ {
+ .mapbase = 0xffe00000,
+ .flags = UPF_BOOT_AUTOCONF,
+ .type = PORT_SCIF,
+ .irqs = { 80, 80, 80, 80 },
+ }, {
+ .flags = 0,
+ }
+};
+
+static struct platform_device sci_device = {
+ .name = "sh-sci",
+ .id = -1,
+ .dev = {
+ .platform_data = sci_platform_data,
+ },
+};
+
+static struct platform_device *sh7366_devices[] __initdata = {
+ &sci_device,
+};
+
+static int __init sh7366_devices_setup(void)
+{
+ return platform_add_devices(sh7366_devices,
+ ARRAY_SIZE(sh7366_devices));
+}
+__initcall(sh7366_devices_setup);
+
+enum {
+ UNUSED=0,
+
+ /* interrupt sources */
+ IRQ0, IRQ1, IRQ2, IRQ3, IRQ4, IRQ5, IRQ6, IRQ7,
+ ICB,
+ DMAC0, DMAC1, DMAC2, DMAC3,
+ VIO_CEUI, VIO_BEUI, VIO_VEUI, VOU,
+ MFI, VPU, USB,
+ MMC_MMC1I, MMC_MMC2I, MMC_MMC3I,
+ DMAC4, DMAC5, DMAC_DADERR,
+ SCIF, SCIFA1, SCIFA2,
+ DENC, MSIOF,
+ FLCTL_FLSTEI, FLCTL_FLENDI, FLCTL_FLTREQ0I, FLCTL_FLTREQ1I,
+ I2C_ALI, I2C_TACKI, I2C_WAITI, I2C_DTEI,
+ SDHI0, SDHI1, SDHI2, SDHI3,
+ CMT, TSIF, SIU,
+ TMU0, TMU1, TMU2,
+ VEU2, LCDC,
+
+ /* interrupt groups */
+
+ DMAC0123, VIOVOU, MMC, DMAC45, FLCTL, I2C, SDHI,
+};
+
+static struct intc_vect vectors[] __initdata = {
+ INTC_VECT(IRQ0, 0x600), INTC_VECT(IRQ1, 0x620),
+ INTC_VECT(IRQ2, 0x640), INTC_VECT(IRQ3, 0x660),
+ INTC_VECT(IRQ4, 0x680), INTC_VECT(IRQ5, 0x6a0),
+ INTC_VECT(IRQ6, 0x6c0), INTC_VECT(IRQ7, 0x6e0),
+ INTC_VECT(ICB, 0x700),
+ INTC_VECT(DMAC0, 0x800), INTC_VECT(DMAC1, 0x820),
+ INTC_VECT(DMAC2, 0x840), INTC_VECT(DMAC3, 0x860),
+ INTC_VECT(VIO_CEUI, 0x880), INTC_VECT(VIO_BEUI, 0x8a0),
+ INTC_VECT(VIO_VEUI, 0x8c0), INTC_VECT(VOU, 0x8e0),
+ INTC_VECT(MFI, 0x900), INTC_VECT(VPU, 0x980), INTC_VECT(USB, 0xa20),
+ INTC_VECT(MMC_MMC1I, 0xb00), INTC_VECT(MMC_MMC2I, 0xb20),
+ INTC_VECT(MMC_MMC3I, 0xb40),
+ INTC_VECT(DMAC4, 0xb80), INTC_VECT(DMAC5, 0xba0),
+ INTC_VECT(DMAC_DADERR, 0xbc0),
+ INTC_VECT(SCIF, 0xc00), INTC_VECT(SCIFA1, 0xc20),
+ INTC_VECT(SCIFA2, 0xc40),
+ INTC_VECT(DENC, 0xc60), INTC_VECT(MSIOF, 0xc80),
+ INTC_VECT(FLCTL_FLSTEI, 0xd80), INTC_VECT(FLCTL_FLENDI, 0xda0),
+ INTC_VECT(FLCTL_FLTREQ0I, 0xdc0), INTC_VECT(FLCTL_FLTREQ1I, 0xde0),
+ INTC_VECT(I2C_ALI, 0xe00), INTC_VECT(I2C_TACKI, 0xe20),
+ INTC_VECT(I2C_WAITI, 0xe40), INTC_VECT(I2C_DTEI, 0xe60),
+ INTC_VECT(SDHI0, 0xe80), INTC_VECT(SDHI1, 0xea0),
+ INTC_VECT(SDHI2, 0xec0), INTC_VECT(SDHI3, 0xee0),
+ INTC_VECT(CMT, 0xf00), INTC_VECT(TSIF, 0xf20),
+ INTC_VECT(SIU, 0xf80),
+ INTC_VECT(TMU0, 0x400), INTC_VECT(TMU1, 0x420),
+ INTC_VECT(TMU2, 0x440),
+ INTC_VECT(VEU2, 0x580), INTC_VECT(LCDC, 0x580),
+};
+
+static struct intc_group groups[] __initdata = {
+ INTC_GROUP(DMAC0123, DMAC0, DMAC1, DMAC2, DMAC3),
+ INTC_GROUP(VIOVOU, VIO_CEUI, VIO_BEUI, VIO_VEUI, VOU),
+ INTC_GROUP(MMC, MMC_MMC1I, MMC_MMC2I, MMC_MMC3I),
+ INTC_GROUP(DMAC45, DMAC4, DMAC5, DMAC_DADERR),
+ INTC_GROUP(FLCTL, FLCTL_FLSTEI, FLCTL_FLENDI,
+ FLCTL_FLTREQ0I, FLCTL_FLTREQ1I),
+ INTC_GROUP(I2C, I2C_ALI, I2C_TACKI, I2C_WAITI, I2C_DTEI),
+ INTC_GROUP(SDHI, SDHI0, SDHI1, SDHI2, SDHI3),
+};
+
+static struct intc_mask_reg mask_registers[] __initdata = {
+ { 0xa4080080, 0xa40800c0, 8, /* IMR0 / IMCR0 */
+ { } },
+ { 0xa4080084, 0xa40800c4, 8, /* IMR1 / IMCR1 */
+ { VOU, VIO_VEUI, VIO_BEUI, VIO_CEUI, DMAC3, DMAC2, DMAC1, DMAC0 } },
+ { 0xa4080088, 0xa40800c8, 8, /* IMR2 / IMCR2 */
+ { 0, 0, 0, VPU, 0, 0, 0, MFI } },
+ { 0xa408008c, 0xa40800cc, 8, /* IMR3 / IMCR3 */
+ { 0, 0, 0, ICB } },
+ { 0xa4080090, 0xa40800d0, 8, /* IMR4 / IMCR4 */
+ { 0, TMU2, TMU1, TMU0, VEU2, 0, 0, LCDC } },
+ { 0xa4080094, 0xa40800d4, 8, /* IMR5 / IMCR5 */
+ { 0, DMAC_DADERR, DMAC5, DMAC4, DENC, SCIFA2, SCIFA1, SCIF } },
+ { 0xa4080098, 0xa40800d8, 8, /* IMR6 / IMCR6 */
+ { 0, 0, 0, 0, 0, 0, 0, MSIOF } },
+ { 0xa408009c, 0xa40800dc, 8, /* IMR7 / IMCR7 */
+ { I2C_DTEI, I2C_WAITI, I2C_TACKI, I2C_ALI,
+ FLCTL_FLTREQ1I, FLCTL_FLTREQ0I, FLCTL_FLENDI, FLCTL_FLSTEI } },
+ { 0xa40800a0, 0xa40800e0, 8, /* IMR8 / IMCR8 */
+ { SDHI3, SDHI2, SDHI1, SDHI0, 0, 0, 0, SIU } },
+ { 0xa40800a4, 0xa40800e4, 8, /* IMR9 / IMCR9 */
+ { 0, 0, 0, CMT, 0, USB, } },
+ { 0xa40800a8, 0xa40800e8, 8, /* IMR10 / IMCR10 */
+ { 0, MMC_MMC3I, MMC_MMC2I, MMC_MMC1I } },
+ { 0xa40800ac, 0xa40800ec, 8, /* IMR11 / IMCR11 */
+ { 0, 0, 0, 0, 0, 0, 0, TSIF } },
+ { 0xa4140044, 0xa4140064, 8, /* INTMSK00 / INTMSKCLR00 */
+ { IRQ0, IRQ1, IRQ2, IRQ3, IRQ4, IRQ5, IRQ6, IRQ7 } },
+};
+
+static struct intc_prio_reg prio_registers[] __initdata = {
+ { 0xa4080000, 0, 16, 4, /* IPRA */ { TMU0, TMU1, TMU2 } },
+ { 0xa4080004, 0, 16, 4, /* IPRB */ { VEU2, LCDC, ICB } },
+ { 0xa4080008, 0, 16, 4, /* IPRC */ { } },
+ { 0xa408000c, 0, 16, 4, /* IPRD */ { } },
+ { 0xa4080010, 0, 16, 4, /* IPRE */ { DMAC0123, VIOVOU, MFI, VPU } },
+ { 0xa4080014, 0, 16, 4, /* IPRF */ { 0, DMAC45, USB, CMT } },
+ { 0xa4080018, 0, 16, 4, /* IPRG */ { SCIF, SCIFA1, SCIFA2, DENC } },
+ { 0xa408001c, 0, 16, 4, /* IPRH */ { MSIOF, 0, FLCTL, I2C } },
+ { 0xa4080020, 0, 16, 4, /* IPRI */ { 0, 0, TSIF, } },
+ { 0xa4080024, 0, 16, 4, /* IPRJ */ { 0, 0, SIU } },
+ { 0xa4080028, 0, 16, 4, /* IPRK */ { 0, MMC, 0, SDHI } },
+ { 0xa408002c, 0, 16, 4, /* IPRL */ { } },
+ { 0xa4140010, 0, 32, 4, /* INTPRI00 */
+ { IRQ0, IRQ1, IRQ2, IRQ3, IRQ4, IRQ5, IRQ6, IRQ7 } },
+};
+
+static struct intc_sense_reg sense_registers[] __initdata = {
+ { 0xa414001c, 16, 2, /* ICR1 */
+ { IRQ0, IRQ1, IRQ2, IRQ3, IRQ4, IRQ5, IRQ6, IRQ7 } },
+};
+
+static DECLARE_INTC_DESC(intc_desc, "sh7366", vectors, groups,
+ mask_registers, prio_registers, sense_registers);
+
+void __init plat_irq_setup(void)
+{
+ register_intc_controller(&intc_desc);
+}
+
+void __init plat_mem_setup(void)
+{
+ /* TODO: Register Node 1 */
+}
--- 0001/arch/sh/kernel/setup.c
+++ work/arch/sh/kernel/setup.c 2008-02-08 15:49:27.000000000 +0900
@@ -324,7 +324,7 @@ static const char *cpu_name[] = {
[CPU_SH7343] = "SH7343", [CPU_SH7785] = "SH7785",
[CPU_SH7722] = "SH7722", [CPU_SHX3] = "SH-X3",
[CPU_SH5_101] = "SH5-101", [CPU_SH5_103] = "SH5-103",
- [CPU_SH_NONE] = "Unknown"
+ [CPU_SH7366] = "SH7366", [CPU_SH_NONE] = "Unknown"
};
const char *get_cpu_subtype(struct sh_cpuinfo *c)
--- 0001/drivers/serial/sh-sci.c
+++ work/drivers/serial/sh-sci.c 2008-02-08 15:49:27.000000000 +0900
@@ -393,7 +393,7 @@ static void sci_init_pins_scif(struct ua
if (cflag & CRTSCTS) {
fcr_val |= SCFCR_MCE;
} else {
-#ifdef CONFIG_CPU_SUBTYPE_SH7343
+#if defined(CONFIG_CPU_SUBTYPE_SH7343) || defined(CONFIG_CPU_SUBTYPE_SH7366)
/* Nothing */
#elif defined(CONFIG_CPU_SUBTYPE_SH7763) || \
defined(CONFIG_CPU_SUBTYPE_SH7780) || \
--- 0001/drivers/serial/sh-sci.h
+++ work/drivers/serial/sh-sci.h 2008-02-08 15:49:27.000000000 +0900
@@ -97,6 +97,12 @@
# define SCSCR_INIT(port) 0x0038 /* TIE=0,RIE=0,TE=1,RE=1,REIE=1 */
# define SCIF_ONLY
# define PORT_PSCR 0xA405011E
+#elif defined(CONFIG_CPU_SUBTYPE_SH7366)
+# define SCPDR0 0xA405013E /* 16 bit SCIF0 PSDR */
+# define SCSPTR0 SCPDR0
+# define SCIF_ORER 0x0001 /* overrun error bit */
+# define SCSCR_INIT(port) 0x0038 /* TIE=0,RIE=0,TE=1,RE=1,REIE=1 */
+# define SCIF_ONLY
#elif defined(CONFIG_CPU_SUBTYPE_SH4_202)
# define SCSPTR2 0xffe80020 /* 16 bit SCIF */
# define SCIF_ORER 0x0001 /* overrun error bit */
@@ -577,7 +583,7 @@ static inline int sci_rxd_in(struct uart
return ctrl_inw(SCSPTR3) & 0x0001 ? 1 : 0; /* SCIF */
return 1;
}
-#elif defined(CONFIG_CPU_SUBTYPE_SH7722)
+#elif defined(CONFIG_CPU_SUBTYPE_SH7722) || defined(CONFIG_CPU_SUBTYPE_SH7366)
static inline int sci_rxd_in(struct uart_port *port)
{
if (port->mapbase = 0xffe00000)
--- 0001/include/asm-sh/cpu-sh4/freq.h
+++ work/include/asm-sh/cpu-sh4/freq.h 2008-02-08 15:55:59.000000000 +0900
@@ -10,12 +10,14 @@
#ifndef __ASM_CPU_SH4_FREQ_H
#define __ASM_CPU_SH4_FREQ_H
-#if defined(CONFIG_CPU_SUBTYPE_SH7722)
+#if defined(CONFIG_CPU_SUBTYPE_SH7722) || defined(CONFIG_CPU_SUBTYPE_SH7366)
#define FRQCR 0xa4150000
#define VCLKCR 0xa4150004
#define SCLKACR 0xa4150008
#define SCLKBCR 0xa415000c
+#if defined(CONFIG_CPU_SUBTYPE_SH7722)
#define IrDACLKCR 0xa4150010
+#endif
#elif defined(CONFIG_CPU_SUBTYPE_SH7763) || \
defined(CONFIG_CPU_SUBTYPE_SH7780)
#define FRQCR 0xffc80000
--- 0001/include/asm-sh/processor.h
+++ work/include/asm-sh/processor.h 2008-02-08 15:49:27.000000000 +0900
@@ -33,7 +33,7 @@ enum cpu_type {
CPU_SH7763, CPU_SH7770, CPU_SH7780, CPU_SH7781, CPU_SH7785, CPU_SHX3,
/* SH4AL-DSP types */
- CPU_SH7343, CPU_SH7722,
+ CPU_SH7343, CPU_SH7722, CPU_SH7366,
/* SH-5 types */
CPU_SH5_101, CPU_SH5_103,
^ permalink raw reply [flat|nested] only message in thread
only message in thread, other threads:[~2008-02-08 8:31 UTC | newest]
Thread overview: (only message) (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2008-02-08 8:31 [PATCH] sh: add support for sh7366 processor Magnus Damm
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.