* [PATCH] b43: Add HostFlags HI support
@ 2008-02-13 13:31 Michael Buesch
0 siblings, 0 replies; only message in thread
From: Michael Buesch @ 2008-02-13 13:31 UTC (permalink / raw)
To: John Linville; +Cc: bcm43xx-dev, linux-wireless
This adds support for the high 16 bits of the hostflags.
No functional change.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
---
John, this is for 2.6.26.
Index: wireless-2.6/drivers/net/wireless/b43/b43.h
===================================================================
--- wireless-2.6.orig/drivers/net/wireless/b43/b43.h 2008-02-13 14:28:06.000000000 +0100
+++ wireless-2.6/drivers/net/wireless/b43/b43.h 2008-02-13 14:28:51.000000000 +0100
@@ -141,13 +141,14 @@ enum {
#define B43_SHM_SH_PCTLWDPOS 0x0008
#define B43_SHM_SH_RXPADOFF 0x0034 /* RX Padding data offset (PIO only) */
#define B43_SHM_SH_PHYVER 0x0050 /* PHY version */
#define B43_SHM_SH_PHYTYPE 0x0052 /* PHY type */
#define B43_SHM_SH_ANTSWAP 0x005C /* Antenna swap threshold */
#define B43_SHM_SH_HOSTFLO 0x005E /* Hostflags for ucode options (low) */
-#define B43_SHM_SH_HOSTFHI 0x0060 /* Hostflags for ucode options (high) */
+#define B43_SHM_SH_HOSTFMI 0x0060 /* Hostflags for ucode options (middle) */
+#define B43_SHM_SH_HOSTFHI 0x0062 /* Hostflags for ucode options (high) */
#define B43_SHM_SH_RFATT 0x0064 /* Current radio attenuation value */
#define B43_SHM_SH_RADAR 0x0066 /* Radar register */
#define B43_SHM_SH_PHYTXNOI 0x006E /* PHY noise directly after TX (lower 8bit only) */
#define B43_SHM_SH_RFRXSP1 0x0072 /* RF RX SP Register 1 */
#define B43_SHM_SH_CHAN 0x00A0 /* Current channel (low 8bit only) */
#define B43_SHM_SH_CHAN_5GHZ 0x0100 /* Bit set, if 5Ghz channel */
@@ -229,37 +230,47 @@ enum {
/* Hardware Radio Enable masks */
#define B43_MMIO_RADIO_HWENABLED_HI_MASK (1 << 16)
#define B43_MMIO_RADIO_HWENABLED_LO_MASK (1 << 4)
/* HostFlags. See b43_hf_read/write() */
-#define B43_HF_ANTDIVHELP 0x00000001 /* ucode antenna div helper */
-#define B43_HF_SYMW 0x00000002 /* G-PHY SYM workaround */
-#define B43_HF_RXPULLW 0x00000004 /* RX pullup workaround */
-#define B43_HF_CCKBOOST 0x00000008 /* 4dB CCK power boost (exclusive with OFDM boost) */
-#define B43_HF_BTCOEX 0x00000010 /* Bluetooth coexistance */
-#define B43_HF_GDCW 0x00000020 /* G-PHY DV canceller filter bw workaround */
-#define B43_HF_OFDMPABOOST 0x00000040 /* Enable PA gain boost for OFDM */
-#define B43_HF_ACPR 0x00000080 /* Disable for Japan, channel 14 */
-#define B43_HF_EDCF 0x00000100 /* on if WME and MAC suspended */
-#define B43_HF_TSSIRPSMW 0x00000200 /* TSSI reset PSM ucode workaround */
-#define B43_HF_DSCRQ 0x00000400 /* Disable slow clock request in ucode */
-#define B43_HF_ACIW 0x00000800 /* ACI workaround: shift bits by 2 on PHY CRS */
-#define B43_HF_2060W 0x00001000 /* 2060 radio workaround */
-#define B43_HF_RADARW 0x00002000 /* Radar workaround */
-#define B43_HF_USEDEFKEYS 0x00004000 /* Enable use of default keys */
-#define B43_HF_BT4PRIOCOEX 0x00010000 /* Bluetooth 2-priority coexistance */
-#define B43_HF_FWKUP 0x00020000 /* Fast wake-up ucode */
-#define B43_HF_VCORECALC 0x00040000 /* Force VCO recalculation when powering up synthpu */
-#define B43_HF_PCISCW 0x00080000 /* PCI slow clock workaround */
-#define B43_HF_4318TSSI 0x00200000 /* 4318 TSSI */
-#define B43_HF_FBCMCFIFO 0x00400000 /* Flush bcast/mcast FIFO immediately */
-#define B43_HF_HWPCTL 0x00800000 /* Enable hardwarre power control */
-#define B43_HF_BTCOEXALT 0x01000000 /* Bluetooth coexistance in alternate pins */
-#define B43_HF_TXBTCHECK 0x02000000 /* Bluetooth check during transmission */
-#define B43_HF_SKCFPUP 0x04000000 /* Skip CFP update */
+#define B43_HF_ANTDIVHELP 0x000000000001ULL /* ucode antenna div helper */
+#define B43_HF_SYMW 0x000000000002ULL /* G-PHY SYM workaround */
+#define B43_HF_RXPULLW 0x000000000004ULL /* RX pullup workaround */
+#define B43_HF_CCKBOOST 0x000000000008ULL /* 4dB CCK power boost (exclusive with OFDM boost) */
+#define B43_HF_BTCOEX 0x000000000010ULL /* Bluetooth coexistance */
+#define B43_HF_GDCW 0x000000000020ULL /* G-PHY DC canceller filter bw workaround */
+#define B43_HF_OFDMPABOOST 0x000000000040ULL /* Enable PA gain boost for OFDM */
+#define B43_HF_ACPR 0x000000000080ULL /* Disable for Japan, channel 14 */
+#define B43_HF_EDCF 0x000000000100ULL /* on if WME and MAC suspended */
+#define B43_HF_TSSIRPSMW 0x000000000200ULL /* TSSI reset PSM ucode workaround */
+#define B43_HF_20IN40IQW 0x000000000200ULL /* 20 in 40 MHz I/Q workaround (rev >= 13 only) */
+#define B43_HF_DSCRQ 0x000000000400ULL /* Disable slow clock request in ucode */
+#define B43_HF_ACIW 0x000000000800ULL /* ACI workaround: shift bits by 2 on PHY CRS */
+#define B43_HF_2060W 0x000000001000ULL /* 2060 radio workaround */
+#define B43_HF_RADARW 0x000000002000ULL /* Radar workaround */
+#define B43_HF_USEDEFKEYS 0x000000004000ULL /* Enable use of default keys */
+#define B43_HF_AFTERBURNER 0x000000008000ULL /* Afterburner enabled */
+#define B43_HF_BT4PRIOCOEX 0x000000010000ULL /* Bluetooth 4-priority coexistance */
+#define B43_HF_FWKUP 0x000000020000ULL /* Fast wake-up ucode */
+#define B43_HF_VCORECALC 0x000000040000ULL /* Force VCO recalculation when powering up synthpu */
+#define B43_HF_PCISCW 0x000000080000ULL /* PCI slow clock workaround */
+#define B43_HF_4318TSSI 0x000000200000ULL /* 4318 TSSI */
+#define B43_HF_FBCMCFIFO 0x000000400000ULL /* Flush bcast/mcast FIFO immediately */
+#define B43_HF_HWPCTL 0x000000800000ULL /* Enable hardwarre power control */
+#define B43_HF_BTCOEXALT 0x000001000000ULL /* Bluetooth coexistance in alternate pins */
+#define B43_HF_TXBTCHECK 0x000002000000ULL /* Bluetooth check during transmission */
+#define B43_HF_SKCFPUP 0x000004000000ULL /* Skip CFP update */
+#define B43_HF_N40W 0x000008000000ULL /* N PHY 40 MHz workaround (rev >= 13 only) */
+#define B43_HF_ANTSEL 0x000020000000ULL /* Antenna selection (for testing antenna div.) */
+#define B43_HF_BT3COEXT 0x000020000000ULL /* Bluetooth 3-wire coexistence (rev >= 13 only) */
+#define B43_HF_BTCANT 0x000040000000ULL /* Bluetooth coexistence (antenna mode) (rev >= 13 only) */
+#define B43_HF_ANTSELEN 0x000100000000ULL /* Antenna selection enabled (rev >= 13 only) */
+#define B43_HF_ANTSELMODE 0x000200000000ULL /* Antenna selection mode (rev >= 13 only) */
+#define B43_HF_MLADVW 0x001000000000ULL /* N PHY ML ADV workaround (rev >= 13 only) */
+#define B43_HF_PR45960W 0x080000000000ULL /* PR 45960 workaround (rev >= 13 only) */
/* MacFilter offsets. */
#define B43_MACFILTER_SELF 0x0000
#define B43_MACFILTER_BSSID 0x0003
/* PowerControl */
Index: wireless-2.6/drivers/net/wireless/b43/main.c
===================================================================
--- wireless-2.6.orig/drivers/net/wireless/b43/main.c 2008-02-13 14:28:06.000000000 +0100
+++ wireless-2.6/drivers/net/wireless/b43/main.c 2008-02-13 14:28:51.000000000 +0100
@@ -461,30 +461,36 @@ void b43_shm_write16(struct b43_wldev *d
b43_write16(dev, B43_MMIO_SHM_DATA, value);
out:
spin_unlock_irqrestore(&wl->shm_lock, flags);
}
/* Read HostFlags */
-u32 b43_hf_read(struct b43_wldev * dev)
+u64 b43_hf_read(struct b43_wldev * dev)
{
- u32 ret;
+ u64 ret;
ret = b43_shm_read16(dev, B43_SHM_SHARED, B43_SHM_SH_HOSTFHI);
ret <<= 16;
+ ret |= b43_shm_read16(dev, B43_SHM_SHARED, B43_SHM_SH_HOSTFMI);
+ ret <<= 16;
ret |= b43_shm_read16(dev, B43_SHM_SHARED, B43_SHM_SH_HOSTFLO);
return ret;
}
/* Write HostFlags */
-void b43_hf_write(struct b43_wldev *dev, u32 value)
+void b43_hf_write(struct b43_wldev *dev, u64 value)
{
- b43_shm_write16(dev, B43_SHM_SHARED,
- B43_SHM_SH_HOSTFLO, (value & 0x0000FFFF));
- b43_shm_write16(dev, B43_SHM_SHARED,
- B43_SHM_SH_HOSTFHI, ((value & 0xFFFF0000) >> 16));
+ u16 lo, mi, hi;
+
+ lo = (value & 0x00000000FFFFULL);
+ mi = (value & 0x0000FFFF0000ULL) >> 16;
+ hi = (value & 0xFFFF00000000ULL) >> 32;
+ b43_shm_write16(dev, B43_SHM_SHARED, B43_SHM_SH_HOSTFLO, lo);
+ b43_shm_write16(dev, B43_SHM_SHARED, B43_SHM_SH_HOSTFMI, mi);
+ b43_shm_write16(dev, B43_SHM_SHARED, B43_SHM_SH_HOSTFHI, hi);
}
void b43_tsf_read(struct b43_wldev *dev, u64 * tsf)
{
/* We need to be careful. As we read the TSF from multiple
* registers, we should take care of register overflows.
Index: wireless-2.6/drivers/net/wireless/b43/main.h
===================================================================
--- wireless-2.6.orig/drivers/net/wireless/b43/main.h 2008-02-13 14:27:37.000000000 +0100
+++ wireless-2.6/drivers/net/wireless/b43/main.h 2008-02-13 14:28:51.000000000 +0100
@@ -92,14 +92,14 @@ void b43_tsf_write(struct b43_wldev *dev
u32 b43_shm_read32(struct b43_wldev *dev, u16 routing, u16 offset);
u16 b43_shm_read16(struct b43_wldev *dev, u16 routing, u16 offset);
void b43_shm_write32(struct b43_wldev *dev, u16 routing, u16 offset, u32 value);
void b43_shm_write16(struct b43_wldev *dev, u16 routing, u16 offset, u16 value);
-u32 b43_hf_read(struct b43_wldev *dev);
-void b43_hf_write(struct b43_wldev *dev, u32 value);
+u64 b43_hf_read(struct b43_wldev *dev);
+void b43_hf_write(struct b43_wldev *dev, u64 value);
void b43_dummy_transmission(struct b43_wldev *dev);
void b43_wireless_core_reset(struct b43_wldev *dev, u32 flags);
void b43_mac_suspend(struct b43_wldev *dev);
^ permalink raw reply [flat|nested] only message in thread
only message in thread, other threads:[~2008-02-13 13:33 UTC | newest]
Thread overview: (only message) (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2008-02-13 13:31 [PATCH] b43: Add HostFlags HI support Michael Buesch
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.