[PATCH 8/9] [POWERPC] Document the mv64x60 device tree bindings

[Dale Farnsworth <dale@farnsworth.org>]

From: Dale Farnsworth <dale@farnsworth.org>

Add the device tree bindings for the Marvell mv64x60 series of
system controller chips in booting-without-of.text.

Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Acked-by: Mark A. Greer <mgreer@mvista.com>

Index: linux-2.6/Documentation/powerpc/booting-without-of.txt
===================================================================
--- linux-2.6.orig/Documentation/powerpc/booting-without-of.txt
+++ linux-2.6/Documentation/powerpc/booting-without-of.txt
@@ -57,7 +57,8 @@ Table of Contents
       n) 4xx/Axon EMAC ethernet nodes
       o) Xilinx IP cores
       p) Freescale Synchronous Serial Interface
-	  q) USB EHCI controllers
+      q) USB EHCI controllers
+      r) Marvell Discovery mv64[345]6x System Controller chips
 
   VII - Specifying interrupt information for devices
     1) interrupts property
@@ -2817,6 +2818,471 @@ platforms are moved over to use the flat
 	   };
 
 
+    r) Marvell Discovery mv64[345]6x System Controller chips.
+
+    Note that while the Marvell mv64[345]60 series of system controller
+    chips are not true system-on-a-chip processors, they essentially
+    contain the peripheral portion of an SOC and the device tree takes
+    the same form, and we will document them here as if they were an SOC.
+    Compatible string values are prefixed with the string "mrvl,",
+    which is the stock ticker symbol for Marvell Technology Group Ltd.
+
+    An SOC node describes the Marvell chip as described in section III.5.f
+    above.
+    
+    Example Marvell Discovery mv64360 SOC node:
+
+	soc@f1000000 { /* Marvell Discovery */
+		#address-cells = <1>;
+		#size-cells = <1>;
+		model = "mv64360";                      /* Default */
+		compatible = "mrvl,mv64360";
+		clock-frequency = <133333333>;
+		reg = <0xf1000000 0x10000>;
+		virtual-reg = <0xf1000000>;
+		ranges = <0x88000000 0x88000000 0x1000000 /* PCI 0 I/O Space */
+			0x80000000 0x80000000 0x8000000 /* PCI 0 MEM Space */
+			0xa0000000 0xa0000000 0x4000000 /* User FLASH */
+			0x00000000 0xf1000000 0x0010000 /* Bridge's regs */
+			0xf2000000 0xf2000000 0x0040000>;/* Integrated SRAM */
+	}
+
+      
+      1. Marvell Discovery MDIO bus
+
+      The MDIO is a bus to which the PHY devices are connected.  For each
+      device that exists on this bus, a child node should be created.  See
+      the definition of the PHY node below for an example of how to define
+      a PHY.
+
+      Required properties:
+        - #address-cells : Should be <1>
+        - #size-cells : Should be <0>
+        - device_type : Should be "mdio"
+        - compatible : Should be "mrvl,mv64360-mdio"
+
+      Example:
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		device_type = "mdio";
+		compatible = "mrvl,mv64360-mdio";
+
+		ethernet-phy@0 {
+			......
+		};
+	};
+
+
+      2.  Marvell Discovery ethernet controller
+      
+      The Discover ethernet controller is described with two levels
+      of nodes.  The first level describes an ethernet silicon block
+      and the second level describes up to 3 ethernet nodes within
+      that block.  The reason for the multiple levels is that the
+      registers for the node are interleaved within a single set
+      of registers.  The "ethernet-block" level describes the
+      shared register set, and the "ethernet" nodes describe ethernet
+      port-specific properties.
+
+      Ethernet block node
+
+      Required properties:
+        - #address-cells : <1>
+	- #size-cells : <0>
+	- compatible : "mrvl,mv64360-eth-block"
+	- reg : Offset and length of the register set for this block
+	
+      Example Discovery Ethernet block node:
+	ethernet-block@2000 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "mrvl,mv64360-eth-block";
+		reg = <0x2000 0x2000>;
+		ethernet@0 {
+			.......
+		};
+	};
+
+      Ethernet port node
+
+      Required properties:
+        - device_type : Should be "network".
+	- compatible : Should be "mrvl,mv64360-eth".
+	- reg : Should be <0>, <1>, or <2>, according to which registers
+	  within the silicon block the device uses.
+	- interrupts : <a> where a is the interrupt number for the port.
+	- interrupt-parent : the phandle for the interrupt controller
+	  that services interrupts for this device.
+	- phy : the phandle for the PHY connected to this ethernet
+	  controller.
+	- local-mac-address : 6 bytes, MAC address
+
+      Example Discovery Ethernet port node:
+	ethernet@0 {
+		device_type = "network";
+		compatible = "mrvl,mv64360-eth";
+		reg = <0>;
+		interrupts = <32>;
+		interrupt-parent = <&PIC>;
+		phy = <&PHY0>;
+		local-mac-address = [ 00 00 00 00 00 00 ];
+	};
+
+
+
+      3.  Marvell Discovery PHY nodes
+
+      Required properties:
+        - device_type : Should be "ethernet-phy"
+        - interrupts : <a> where a is the interrupt number for this phy.
+        - interrupt-parent : the phandle for the interrupt controller that
+          services interrupts for this device.
+        - reg : The ID number for the phy, usually a small integer
+
+      Example Discovery PHY node:
+	ethernet-phy@1 {
+		device_type = "ethernet-phy";
+		compatible = "broadcom,bcm5421";
+		interrupts = <76>;      /* GPP 12 */
+		interrupt-parent = <&PIC>;
+		reg = <1>;
+	};
+
+
+
+      4.  Marvell Discovery SDMA nodes
+      Represent DMA hardware associated with the MPSC (multiprotocol
+      serial controllers).
+
+      Required properties:
+        - compatible : "mrvl,mv64360-sdma"
+	- reg : Offset and length of the register set for this device
+	- interrupts : <a> where a is the interrupt number for the DMA
+	  device.
+	- interrupt-parent : the phandle for the interrupt controller
+	  that services interrupts for this device.
+
+      Example Discovery SDMA node:
+	sdma@4000 {
+		compatible = "mrvl,mv64360-sdma";
+		reg = <0x4000 0xc18>;
+		virtual-reg = <0xf1004000>;
+		interrupts = <36>;
+		interrupt-parent = <&PIC>;
+	};
+      
+
+      5.  Marvell Discovery BRG nodes
+      Represent baud rate generator hardware associated with the MPSC
+      (multiprotocol serial controllers).
+
+      Required properties:
+        - compatible : "mrvl,mv64360-brg"
+	- reg : Offset and length of the register set for this device
+	- clock-src : A value from 0 to 15 which selects the clock
+	  source for the baud rate generator.  This value corresponds
+	  to the CLKS value in the BRGx configuration register.  See
+	  the mv64x60 User's Manual.
+	- clock-frequence : The frequency (in Hz) of the baud rate
+	  generator's input clock.
+	- current-speed : The current speed setting (presumably by
+	  firmware) of the baud rate generator.
+
+      Example Discovery BRG node:
+        brg@b200 {
+		compatible = "mrvl,mv64360-brg";
+		reg = <0xb200 0x8>;
+		clock-src = <8>;
+		clock-frequency = <133333333>;
+		current-speed = <9600>;
+	};
+
+      
+      6.  Marvell Discovery CUNIT nodes
+      Represent the Serial Communications Unit device hardware.
+
+      Required properties:
+	- reg : Offset and length of the register set for this device
+
+      Example Discovery CUNIT node:
+        cunit@f200 {
+		reg = <0xf200 0x200>;
+	};
+
+
+      7.  Marvell Discovery MPSCROUTING nodes
+      Represent the Discovery's MPSC routing hardware
+
+      Required properties:
+	- reg : Offset and length of the register set for this device
+
+      Example Discovery CUNIT node:
+        mpscrouting@b500 {
+		reg = <0xb400 0xc>;
+	};
+
+
+      8.  Marvell Discovery MPSCINTR nodes
+      Represent the Discovery's MPSC DMA interrupt hardware registers
+      (SDMA cause and mask registers).
+
+      Required properties:
+	- reg : Offset and length of the register set for this device
+
+      Example Discovery MPSCINTR node:
+        mpsintr@b800 {
+		reg = <0xb800 0x100>;
+	};
+
+
+      9.  Marvell Discovery MPSC nodes
+      Represent the Discovery's MPSC (Multiprotocol Serial Controller)
+      serial port.
+
+      Required properties:
+        - device_type : "serial"
+	- compatible : "mrvl,mv64360-mpsc"
+	- reg : Offset and length of the register set for this device
+	- sdma : the phandle for the SDMA node used by this port
+	- brg : the phandle for the BRG node used by this port
+	- cunit : the phandle for the CUNIT node used by this port
+	- mpscrouting : the phandle for the MPSCROUTING node used by this port
+	- mpscintr : the phandle for the MPSCINTR node used by this port
+	- cell-index : the hardware index of this cell in the MPSC core
+	- max_idle : value needed for MPSC CHR3 (Maximum Frame Length)
+	  register
+	- interrupts : <a> where a is the interrupt number for the MPSC.
+	- interrupt-parent : the phandle for the interrupt controller
+	  that services interrupts for this device.
+	
+      Example Discovery MPSCINTR node:
+        mpsc@8000 {
+		device_type = "serial";
+		compatible = "mrvl,mv64360-mpsc";
+		reg = <0x8000 0x38>;
+		virtual-reg = <0xf1008000>;
+		sdma = <&SDMA0>;
+		brg = <&BRG0>;
+		cunit = <&CUNIT>;
+		mpscrouting = <&MPSCROUTING>;
+		mpscintr = <&MPSCINTR>;
+		cell-index = <0>;
+		max_idle = <40>;
+		interrupts = <40>;
+		interrupt-parent = <&PIC>;
+	};
+
+
+      10.  Marvell Discovery Watch Dog Timer nodes
+      Represent the Discovery's watchdog timer hardware
+
+      Required properties:
+        - compatible : "mrvl,mv64360-wdt"
+	- reg : Offset and length of the register set for this device
+
+      Example Discovery Watch Dog Timer node:
+        wdt@b410 {
+		compatible = "mrvl,mv64360-wdt";
+		reg = <0xb410 0x8>;
+	};
+
+
+      11.  Marvell Discovery I2C nodes
+      Represent the Discovery's I2C hardware
+
+      Required properties:
+        - device_type : "i2c"
+        - compatible : "mrvl,mv64360-i2c"
+	- reg : Offset and length of the register set for this device
+	- interrupts : <a> where a is the interrupt number for the I2C.
+	- interrupt-parent : the phandle for the interrupt controller
+	  that services interrupts for this device.
+
+      Example Discovery I2C node:
+		compatible = "mrvl,mv64360-i2c";
+		reg = <0xc000 0x20>;
+		virtual-reg = <0xf100c000>;
+		interrupts = <37>;
+		interrupt-parent = <&PIC>;
+	};
+
+
+      12.  Marvell Discovery PIC (Programmable Interrupt Controller) nodes
+      Represent the Discovery's PIC hardware
+
+      Required properties:
+        - #interrupt-cells : <1>
+	- #address-cells : <0>
+	- compatible : "mrvl,mv64360-pic"
+	- reg : Offset and length of the register set for this device
+	- interrupt-controller
+
+      Example Discovery PIC node:
+        pic {
+		#interrupt-cells = <1>;
+		#address-cells = <0>;
+		compatible = "mrvl,mv64360-pic";
+		reg = <0x0 0x88>;
+		interrupt-controller;
+	};
+
+
+      13.  Marvell Discovery MPP (Multipurpose Pins) multiplexing nodes
+      Represent the Discovery's MPP hardware
+
+      Required properties:
+        - compatible : "mrvl,mv64360-mpp"
+	- reg : Offset and length of the register set for this device
+
+      Example Discovery MPP node:
+	mpp@f000 {
+		compatible = "mrvl,mv64360-mpp";
+		reg = <0xf000 0x10>;
+	};
+
+
+      14.  Marvell Discovery GPP (General Purpose Pins) nodes
+      Represent the Discovery's GPP hardware
+
+      Required properties:
+        - compatible : "mrvl,mv64360-gpp"
+	- reg : Offset and length of the register set for this device
+
+      Example Discovery GPP node:
+	gpp@f000 {
+		compatible = "mrvl,mv64360-gpp";
+		reg = <0xf100 0x20>;
+	};
+
+
+      15.  Marvell Discovery PCI host bridge node
+      Represents the Discovery's PCI host bridge device.  The properties
+      for this node conform to Rev 2.1 of the PCI Bus Binding to IEEE
+      1275-1994.  A typical value for the compatible property is
+      "mrvl,mv64360-pci".
+
+      Example Discovery PCI host bridge node
+	pci@80000000 {       
+		#address-cells = <3>;
+		#size-cells = <2>;
+		#interrupt-cells = <1>;
+		device_type = "pci";
+		compatible = "mrvl,mv64360-pci";
+		reg = <0xcf8 0x8>;
+		ranges = <0x01000000 0x0        0x0
+				0x88000000 0x0 0x01000000
+			  0x02000000 0x0 0x80000000
+				0x80000000 0x0 0x08000000>;
+		bus-range = <0 255>;
+		clock-frequency = <66000000>;
+		interrupt-parent = <&PIC>;
+		interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
+		interrupt-map = <
+			/* IDSEL 0x0a */
+			0x5000 0 0 1 &PIC 80
+			0x5000 0 0 2 &PIC 81
+			0x5000 0 0 3 &PIC 91
+			0x5000 0 0 4 &PIC 93
+
+			/* IDSEL 0x0b */
+			0x5800 0 0 1 &PIC 91
+			0x5800 0 0 2 &PIC 93
+			0x5800 0 0 3 &PIC 80
+			0x5800 0 0 4 &PIC 81
+
+			/* IDSEL 0x0c */
+			0x6000 0 0 1 &PIC 91
+			0x6000 0 0 2 &PIC 93
+			0x6000 0 0 3 &PIC 80
+			0x6000 0 0 4 &PIC 81
+
+			/* IDSEL 0x0d */
+			0x6800 0 0 1 &PIC 93
+			0x6800 0 0 2 &PIC 80
+			0x6800 0 0 3 &PIC 81
+			0x6800 0 0 4 &PIC 91
+		>;
+	};
+
+
+      16.  Marvell Discovery CPU Error nodes
+      Represent the Discovery's CPU error handler device.
+
+      Required properties:
+        - compatible : "mrvl,mv64360-cpu-error"
+	- reg : Offset and length of the register set for this device
+	- interrupts : the interrupt number for this device
+	- interrupt-parent : the phandle for the interrupt controller
+	  that services interrupts for this device.
+
+      Example Discovery CPU Error node:
+	cpu-error@0070 {
+		compatible = "mrvl,mv64360-cpu-error";
+		reg = <0x70 0x10 0x128 0x28>;
+		interrupts = <3>;
+		interrupt-parent = <&PIC>;
+	};
+
+
+      17.  Marvell Discovery SRAM Controller nodes
+      Represent the Discovery's SRAM controller device.
+
+      Required properties:
+        - compatible : "mrvl,mv64360-sram-ctrl"
+	- reg : Offset and length of the register set for this device
+	- interrupts : the interrupt number for this device
+	- interrupt-parent : the phandle for the interrupt controller
+	  that services interrupts for this device.
+
+      Example Discovery SRAM Controller node:
+	sram-ctrl@0380 {
+		compatible = "mrvl,mv64360-sram-ctrl";
+		reg = <0x380 0x80>;
+		interrupts = <13>;
+		interrupt-parent = <&PIC>;
+	};
+
+
+      18.  Marvell Discovery PCI Error Handler nodes
+      Represent the Discovery's PCI error handler device.
+
+      Required properties:
+        - compatible : "mrvl,mv64360-pci-error"
+	- reg : Offset and length of the register set for this device
+	- interrupts : the interrupt number for this device
+	- interrupt-parent : the phandle for the interrupt controller
+	  that services interrupts for this device.
+
+      Example Discovery PCI Error Handler node:
+	pci-error@1d40 {
+		compatible = "mrvl,mv64360-pci-error";
+		reg = <0x1d40 0x40 0xc28 0x4>;
+		interrupts = <12>;
+		interrupt-parent = <&PIC>;
+	};
+
+
+      19.  Marvell Discovery Memory Controller nodes
+      Represent the Discovery's memory controller device.
+
+      Required properties:
+        - compatible : "mrvl,mv64360-mem-ctrl"
+	- reg : Offset and length of the register set for this device
+	- interrupts : the interrupt number for this device
+	- interrupt-parent : the phandle for the interrupt controller
+	  that services interrupts for this device.
+
+      Example Discovery Memory Controller node:
+	mem-ctrl@1400 {
+		compatible = "mrvl,mv64360-mem-ctrl";
+		reg = <0x1400 0x60>;
+		interrupts = <17>;
+		interrupt-parent = <&PIC>;
+	};
+
+
    More devices will be defined as this spec matures.
 
 VII - Specifying interrupt information for devices