From: "Denys Fedoryshchenko" <denys@visp.net.lb>
To: netdev@vger.kernel.org
Subject: Re: packetloss, on e1000e worse than r8169?
Date: Mon, 16 Jun 2008 23:52:54 +0300 [thread overview]
Message-ID: <20080616205254.M50992@visp.net.lb> (raw)
In-Reply-To: <4856CEDC.6010706@intel.com>
On Mon, 16 Jun 2008 13:36:44 -0700, Kok, Auke wrote
> Denys Fedoryshchenko wrote:
> > Also if important
> > MegaRouter-KARAM ~ # dmesg|grep eth1
> > [ 3.955620] eth1: (PCI Express:2.5GB/s:Width x1) 00:19:d1:71:5f:33
> > [ 3.955622] eth1: Intel(R) PRO/1000 Network Connection
> > [ 3.955642] eth1: MAC: 4, PHY: 6, PBA No: ffffff-0ff
> > [ 5.358191] netconsole: interface eth1
>
> please disable netconsole on this device. You should not run
> netconsole over a critical (and busy) line like this.
>
> > [ 6.432345] eth1: Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
> >
> > MegaRouter-KARAM ~ # ethtool eth1
> > Settings for eth1:
> > Supported ports: [ TP ]
> > Supported link modes: 10baseT/Half 10baseT/Full
> > 100baseT/Half 100baseT/Full
> > 1000baseT/Full
> > Supports auto-negotiation: Yes
> > Advertised link modes: 10baseT/Half 10baseT/Full
> > 100baseT/Half 100baseT/Full
> > 1000baseT/Full
> > Advertised auto-negotiation: Yes
> > Speed: 1000Mb/s
> > Duplex: Full
> > Port: Twisted Pair
> > PHYAD: 1
> > Transceiver: internal
> > Auto-negotiation: on
> > Supports Wake-on: pumbag
> > Wake-on: g
> > Current message level: 0x00000001 (1)
> > Link detected: yes
> >
> >
> > MegaRouter-KARAM ~ # ethtool -c eth1
> > Coalesce parameters for eth1:
> > Adaptive RX: off TX: off
> > stats-block-usecs: 0
> > sample-interval: 0
> > pkt-rate-low: 0
> > pkt-rate-high: 0
> >
> > rx-usecs: 3
> >
> > I tried to change Intel's "magic" rx-usecs to 0,1,3,10000,100000, it doesn't
> > help at all. Attempt to change offloading parameters (disabling) doesn't make
> > sense too.
> >
> >
> > On Mon, 16 Jun 2008 21:48:55 +0200, Eric Dumazet wrote
> >> Denys Fedoryshchenko a e'crit :
> >>> Hi again
> >>>
> >>> I moved from PCI Realtek 8169 to onboard PCI-Express e1000e, and situation
> >>> become worse. Strange? Yes.
> >>>
> >>> Here is info
> >>> Load and error rate:
> >>>
> >>> MegaRouter-KARAM /sys # ifconfig eth1;sleep 10;ifconfig eth1
> >>> eth1 Link encap:Ethernet HWaddr 00:19:D1:71:5F:33
> >>> inet addr:192.168.20.10 Bcast:0.0.0.0 Mask:255.255.255.0
> >>> UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
> >>> RX packets:91991642 errors:0 dropped:1803444 overruns:0 frame:0
> >>> TX packets:91914611 errors:0 dropped:0 overruns:0 carrier:0
> >>> collisions:0 txqueuelen:1000
> >>> RX bytes:316112765 (301.4 MiB) TX bytes:138303107 (131.8 MiB)
> >>> Memory:90300000-90320000
> >>>
> >>> eth1 Link encap:Ethernet HWaddr 00:19:D1:71:5F:33
> >>> inet addr:192.168.20.10 Bcast:0.0.0.0 Mask:255.255.255.0
> >>> UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
> >>> RX packets:92812514 errors:0 dropped:1815490 overruns:0 frame:0
> >>> TX packets:92734865 errors:0 dropped:0 overruns:0 carrier:0
> >>> collisions:0 txqueuelen:1000
> >>> RX bytes:739941322 (705.6 MiB) TX bytes:560547138 (534.5 MiB)
> >>> Memory:90300000-90320000
> >>>
> >>> System load (there is no NAT, no shapers, just routing, around 600-700
> > routes):
> >>> MegaRouter-KARAM /sys # mpstat 1
> >>> Linux 2.6.26-rc6-git2-build-0029 (MegaRouter-KARAM) 06/16/08
> >>>
> >>> 22:36:36 CPU %user %nice %sys %iowait %irq %soft %steal
> >>> %idle intr/s
> >>> 22:36:37 all 0.00 0.00 0.00 0.00 0.00 1.49 0.00
> >>> 98.51 19764.00
> >>> 22:36:38 all 0.00 0.00 0.50 0.00 0.00 0.50 0.00
> >>> 99.01 19888.00
> >>> 22:36:39 all 0.00 0.00 0.00 0.00 0.00 0.50 0.00
> >>> 99.50 19642.00
> >>> 22:36:40 all 0.00 0.00 0.00 0.00 1.01 9.05 0.00
> >>> 89.95 19543.00
> >>>
> >>> (system almost idle)
> >>>
> >>> MegaRouter-KARAM /sys # ethtool -S eth1
> >>> NIC statistics:
> >>> rx_packets: 109977509
> >>> tx_packets: 109887692
> >>> rx_bytes: 57656749138
> >>> tx_bytes: 57536071746
> >>> rx_broadcast: 6497
> >>> tx_broadcast: 92
> >>> rx_multicast: 48995
> >>> tx_multicast: 1960
> >>> rx_errors: 0
> >>> tx_errors: 0
> >>> tx_dropped: 0
> >>> multicast: 48995
> >>> collisions: 0
> >>> rx_length_errors: 0
> >>> rx_over_errors: 0
> >>> rx_crc_errors: 0
> >>> rx_frame_errors: 0
> >>> rx_no_buffer_count: 1796
> >>> rx_missed_errors: 2182679
> >>> tx_aborted_errors: 0
> >>> tx_carrier_errors: 0
> >>> tx_fifo_errors: 0
> >>> tx_heartbeat_errors: 0
> >>> tx_window_errors: 0
> >>> tx_abort_late_coll: 0
> >>> tx_deferred_ok: 55617
> >>> tx_single_coll_ok: 0
> >>> tx_multi_coll_ok: 0
> >>> tx_timeout_count: 0
> >>> tx_restart_queue: 1626
> >>> rx_long_length_errors: 0
> >>> rx_short_length_errors: 0
> >>> rx_align_errors: 0
> >>> tx_tcp_seg_good: 0
> >>> tx_tcp_seg_failed: 0
> >>> rx_flow_control_xon: 55461
> >>> rx_flow_control_xoff: 57329
> >>> tx_flow_control_xon: 39114
> >>> tx_flow_control_xoff: 48341
> >>> rx_long_byte_count: 57656749138
> >>> rx_csum_offload_good: 104097306
> >>> rx_csum_offload_errors: 2209
> >>> rx_header_split: 0
> >>> alloc_rx_buff_failed: 0
> >>> tx_smbus: 22
> >>> rx_smbus: 2201
> >>> dropped_smbus: 0
> >>> rx_dma_failed: 0
> >>> tx_dma_failed: 0
> >>> MegaRouter-KARAM /sys # ethtool -S eth1
> >>> NIC statistics:
> >>> rx_packets: 110154571
> >>> tx_packets: 110064459
> >>> rx_bytes: 57753358981
> >>> tx_bytes: 57632419451
> >>> rx_broadcast: 6501
> >>> tx_broadcast: 92
> >>> rx_multicast: 49155
> >>> tx_multicast: 1960
> >>> rx_errors: 0
> >>> tx_errors: 0
> >>> tx_dropped: 0
> >>> multicast: 49155
> >>> collisions: 0
> >>> rx_length_errors: 0
> >>> rx_over_errors: 0
> >>> rx_crc_errors: 0
> >>> rx_frame_errors: 0
> >>> rx_no_buffer_count: 1796
> >>> rx_missed_errors: 2187703
> >>> tx_aborted_errors: 0
> >>> tx_carrier_errors: 0
> >>> tx_fifo_errors: 0
> >>> tx_heartbeat_errors: 0
> >>> tx_window_errors: 0
> >>> tx_abort_late_coll: 0
> >>> tx_deferred_ok: 55772
> >>> tx_single_coll_ok: 0
> >>> tx_multi_coll_ok: 0
> >>> tx_timeout_count: 0
> >>> tx_restart_queue: 1628
> >>> rx_long_length_errors: 0
> >>> rx_short_length_errors: 0
> >>> rx_align_errors: 0
> >>> tx_tcp_seg_good: 0
> >>> tx_tcp_seg_failed: 0
> >>> rx_flow_control_xon: 55615
> >>> rx_flow_control_xoff: 57488
> >>> tx_flow_control_xon: 39209
> >>> tx_flow_control_xoff: 48448
> >>> rx_long_byte_count: 57753358981
> >>> rx_csum_offload_good: 104264656
> >>> rx_csum_offload_errors: 2210
> >>> rx_header_split: 0
> >>> alloc_rx_buff_failed: 0
> >>> tx_smbus: 23
> >>> rx_smbus: 2207
> >>> dropped_smbus: 0
> >>> rx_dma_failed: 0
> >>> tx_dma_failed: 0
> >>>
> >>>
> >>>
> >> What RX & TX rings look like on e1000e ?
> >>
> >> ethtool -g eth1
> >>
> >> Also, please post "cat /proc/interrupts"
> >>
Disabled and rebooted. It changes nothing. (By the way it is first thing i tried).
MegaRouter-KARAM ~ # ifconfig eth1;sleep 10;ifconfig eth1
eth1 Link encap:Ethernet HWaddr 00:19:D1:71:5F:33
inet addr:192.168.20.10 Bcast:0.0.0.0 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:4507198 errors:0 dropped:12335 overruns:0 frame:0
TX packets:4494262 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:1431300040 (1.3 GiB) TX bytes:1421772965 (1.3 GiB)
Memory:90300000-90320000
eth1 Link encap:Ethernet HWaddr 00:19:D1:71:5F:33
inet addr:192.168.20.10 Bcast:0.0.0.0 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:5546385 errors:0 dropped:20298 overruns:0 frame:0
TX packets:5531599 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:1849199364 (1.7 GiB) TX bytes:1837492827 (1.7 GiB)
Memory:90300000-90320000
Here is full dmesg, as proof, that it is off
] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[ 0.235558] ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 16 (level, low) ->
IRQ 16
[ 0.235562] PCI: Setting latency timer of device 0000:00:1c.1 to 64
[ 0.235576] ACPI: PCI Interrupt 0000:00:1c.2[C] -> GSI 18 (level, low) ->
IRQ 18
[ 0.235580] PCI: Setting latency timer of device 0000:00:1c.2 to 64
[ 0.235593] ACPI: PCI Interrupt 0000:00:1c.3[D] -> GSI 19 (level, low) ->
IRQ 19
[ 0.235597] PCI: Setting latency timer of device 0000:00:1c.3 to 64
[ 0.235611] ACPI: PCI Interrupt 0000:00:1c.4[A] -> GSI 17 (level, low) ->
IRQ 17
[ 0.235615] PCI: Setting latency timer of device 0000:00:1c.4 to 64
[ 0.235623] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[ 0.235631] NET: Registered protocol family 2
[ 0.241017] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.241231] TCP established hash table entries: 131072 (order: 8, 1048576
bytes)
[ 0.241532] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.241671] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.241673] TCP reno registered
[ 0.242025] NET: Registered protocol family 1
[ 0.323486] Machine check exception polling timer started.
[ 0.323843] highmem bounce pool size: 64 pages
[ 0.325672] JFFS2 version 2.2. (SUMMARY) 2001-2006 Red Hat, Inc.
[ 0.325828] msgmni has been set to 1741
[ 0.325962] Block layer SCSI generic (bsg) driver version 0.4 loaded (major
254)
[ 0.325962] io scheduler noop registered
[ 0.325962] io scheduler cfq registered (default)
[ 0.325962] pci 0000:00:02.0: Boot video device
[ 0.326137] PCI: Setting latency timer of device 0000:00:01.0 to 64
[ 0.326161] assign_interrupt_mode Found MSI capability
[ 0.326181] Allocate Port Service[0000:00:01.0:pcie00]
[ 0.326212] Allocate Port Service[0000:00:01.0:pcie03]
[ 0.326272] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[ 0.326299] assign_interrupt_mode Found MSI capability
[ 0.326325] Allocate Port Service[0000:00:1c.0:pcie00]
[ 0.326354] Allocate Port Service[0000:00:1c.0:pcie02]
[ 0.326381] Allocate Port Service[0000:00:1c.0:pcie03]
[ 0.326447] PCI: Setting latency timer of device 0000:00:1c.1 to 64
[ 0.326473] assign_interrupt_mode Found MSI capability
[ 0.326499] Allocate Port Service[0000:00:1c.1:pcie00]
[ 0.326528] Allocate Port Service[0000:00:1c.1:pcie02]
[ 0.326558] Allocate Port Service[0000:00:1c.1:pcie03]
[ 0.326624] PCI: Setting latency timer of device 0000:00:1c.2 to 64
[ 0.326650] assign_interrupt_mode Found MSI capability
[ 0.326676] Allocate Port Service[0000:00:1c.2:pcie00]
[ 0.326705] Allocate Port Service[0000:00:1c.2:pcie02]
[ 0.326734] Allocate Port Service[0000:00:1c.2:pcie03]
[ 0.326801] PCI: Setting latency timer of device 0000:00:1c.3 to 64
[ 0.326827] assign_interrupt_mode Found MSI capability
[ 0.326852] Allocate Port Service[0000:00:1c.3:pcie00]
[ 0.326881] Allocate Port Service[0000:00:1c.3:pcie02]
[ 0.326908] Allocate Port Service[0000:00:1c.3:pcie03]
[ 0.326963] PCI: Setting latency timer of device 0000:00:1c.4 to 64
[ 0.326963] assign_interrupt_mode Found MSI capability
[ 0.326992] Allocate Port Service[0000:00:1c.4:pcie00]
[ 0.327021] Allocate Port Service[0000:00:1c.4:pcie02]
[ 0.327048] Allocate Port Service[0000:00:1c.4:pcie03]
[ 0.341961] hpet_resources: 0xfed00000 is busy
[ 0.342028] Driver 'sd' needs updating - please use bus_type methods
[ 0.342159] PNP: No PS/2 controller found. Probing ports directly.
[ 0.345015] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.345019] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 0.345081] mice: PS/2 mouse device common for all mice
[ 0.345164] input: PC Speaker as /class/input/input0
[ 0.499965] Clockevents: could not switch to one-shot mode: lapic is not
functional.
[ 0.499969] Could not switch to high resolution mode on CPU 1
[ 0.500964] Clockevents: could not switch to one-shot mode: lapic is not
functional.
[ 0.500968] Could not switch to high resolution mode on CPU 0
[ 0.510859] device-mapper: uevent: version 1.0.3
[ 0.510949] device-mapper: ioctl: 4.13.0-ioctl (2007-10-18) initialised:
dm-devel@redhat.com
[ 0.510949] cpuidle: using governor ladder
[ 0.510949] cpuidle: using governor menu
[ 0.511209] TCP cubic registered
[ 0.511211] NET: Registered protocol family 17
[ 0.511220] Using IPI Shortcut mode
[ 0.513051] Freeing unused kernel memory: 5508k freed
[ 0.860439] usbcore: registered new interface driver usbfs
[ 0.860488] usbcore: registered new interface driver hub
[ 0.860534] usbcore: registered new device driver usb
[ 0.889476] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI)
Driver
[ 0.918682] ACPI: PCI Interrupt 0000:00:1a.7[C] -> GSI 18 (level, low) ->
IRQ 18
[ 0.918694] PCI: Setting latency timer of device 0000:00:1a.7 to 64
[ 0.918697] ehci_hcd 0000:00:1a.7: EHCI Host Controller
[ 0.918876] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus
number 1
[ 0.922777] ehci_hcd 0000:00:1a.7: debug port 1
[ 0.922783] PCI: cache line size of 32 is not supported by device 0000:00:1a.7
[ 0.922792] ehci_hcd 0000:00:1a.7: irq 18, io mem 0x90326c00
[ 0.931942] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10
Dec 2004
[ 0.932035] usb usb1: configuration #1 chosen from 1 choice
[ 0.932089] hub 1-0:1.0: USB hub found
[ 0.932096] hub 1-0:1.0: 4 ports detected
[ 1.033074] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.033078] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.033082] usb usb1: Product: EHCI Host Controller
[ 1.033084] usb usb1: Manufacturer: Linux 2.6.26-rc6-git2-build-0029 ehci_hcd
[ 1.033086] usb usb1: SerialNumber: 0000:00:1a.7
[ 1.033113] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) ->
IRQ 23
[ 1.033122] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[ 1.033126] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 1.033177] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus
number 2
[ 1.037079] ehci_hcd 0000:00:1d.7: debug port 1
[ 1.037085] PCI: cache line size of 32 is not supported by device 0000:00:1d.7
[ 1.037091] ehci_hcd 0000:00:1d.7: irq 23, io mem 0x90326800
[ 1.046922] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10
Dec 2004
[ 1.047013] usb usb2: configuration #1 chosen from 1 choice
[ 1.047064] hub 2-0:1.0: USB hub found
[ 1.047071] hub 2-0:1.0: 6 ports detected
[ 1.148018] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.148021] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.148025] usb usb2: Product: EHCI Host Controller
[ 1.148028] usb usb2: Manufacturer: Linux 2.6.26-rc6-git2-build-0029 ehci_hcd
[ 1.148030] usb usb2: SerialNumber: 0000:00:1d.7
[ 1.178131] USB Universal Host Controller Interface driver v3.0
[ 1.178162] ACPI: PCI Interrupt 0000:00:1a.0[A] -> GSI 16 (level, low) ->
IRQ 16
[ 1.178169] PCI: Setting latency timer of device 0000:00:1a.0 to 64
[ 1.178172] uhci_hcd 0000:00:1a.0: UHCI Host Controller
[ 1.178211] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus
number 3
[ 1.178235] uhci_hcd 0000:00:1a.0: irq 16, io base 0x000030c0
[ 1.178309] usb usb3: configuration #1 chosen from 1 choice
[ 1.178347] hub 3-0:1.0: USB hub found
[ 1.178353] hub 3-0:1.0: 2 ports detected
[ 1.279009] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.279013] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.279017] usb usb3: Product: UHCI Host Controller
[ 1.279020] usb usb3: Manufacturer: Linux 2.6.26-rc6-git2-build-0029 uhci_hcd
[ 1.279023] usb usb3: SerialNumber: 0000:00:1a.0
[ 1.279042] ACPI: PCI Interrupt 0000:00:1a.1[B] -> GSI 21 (level, low) ->
IRQ 21
[ 1.279050] PCI: Setting latency timer of device 0000:00:1a.1 to 64
[ 1.279054] uhci_hcd 0000:00:1a.1: UHCI Host Controller
[ 1.279101] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus
number 4
[ 1.279127] uhci_hcd 0000:00:1a.1: irq 21, io base 0x000030a0
[ 1.279212] usb usb4: configuration #1 chosen from 1 choice
[ 1.279253] hub 4-0:1.0: USB hub found
[ 1.279257] hub 4-0:1.0: 2 ports detected
[ 1.353906] usb 2-4: new high speed USB device using ehci_hcd and address 2
[ 1.380002] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.380006] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.380010] usb usb4: Product: UHCI Host Controller
[ 1.380013] usb usb4: Manufacturer: Linux 2.6.26-rc6-git2-build-0029 uhci_hcd
[ 1.380016] usb usb4: SerialNumber: 0000:00:1a.1
[ 1.380039] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) ->
IRQ 23
[ 1.380047] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[ 1.380051] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 1.380099] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus
number 5
[ 1.380121] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00003080
[ 1.380205] usb usb5: configuration #1 chosen from 1 choice
[ 1.380244] hub 5-0:1.0: USB hub found
[ 1.380249] hub 5-0:1.0: 2 ports detected
[ 1.470314] usb 2-4: configuration #1 chosen from 1 choice
[ 1.470643] usb 2-4: New USB device found, idVendor=0951, idProduct=1603
[ 1.470645] usb 2-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 1.470647] usb 2-4: Product: DataTraveler 2.0
[ 1.470649] usb 2-4: Manufacturer: Kingston
[ 1.470650] usb 2-4: SerialNumber: 8990000000000000000000FB
[ 1.481001] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.481004] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.481008] usb usb5: Product: UHCI Host Controller
[ 1.481011] usb usb5: Manufacturer: Linux 2.6.26-rc6-git2-build-0029 uhci_hcd
[ 1.481015] usb usb5: SerialNumber: 0000:00:1d.0
[ 1.481033] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) ->
IRQ 19
[ 1.481041] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[ 1.481044] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 1.481094] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus
number 6
[ 1.481120] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00003060
[ 1.481204] usb usb6: configuration #1 chosen from 1 choice
[ 1.481242] hub 6-0:1.0: USB hub found
[ 1.481248] hub 6-0:1.0: 2 ports detected
[ 1.581993] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.581996] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.582000] usb usb6: Product: UHCI Host Controller
[ 1.582003] usb usb6: Manufacturer: Linux 2.6.26-rc6-git2-build-0029 uhci_hcd
[ 1.582007] usb usb6: SerialNumber: 0000:00:1d.1
[ 1.582025] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) ->
IRQ 18
[ 1.582033] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[ 1.582037] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 1.582083] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus
number 7
[ 1.582105] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00003040
[ 1.582189] usb usb7: configuration #1 chosen from 1 choice
[ 1.582226] hub 7-0:1.0: USB hub found
[ 1.582231] hub 7-0:1.0: 2 ports detected
[ 1.682982] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.682985] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.682989] usb usb7: Product: UHCI Host Controller
[ 1.682992] usb usb7: Manufacturer: Linux 2.6.26-rc6-git2-build-0029 uhci_hcd
[ 1.682996] usb usb7: SerialNumber: 0000:00:1d.2
[ 1.712358] usbcore: registered new interface driver usbhid
[ 1.712361] usbhid: v2.6:USB HID core driver
[ 1.801687] Initializing USB Mass Storage driver...
[ 1.801739] scsi0 : SCSI emulation for USB Mass Storage devices
[ 1.801784] usb-storage: device found at 2
[ 1.801852] usbcore: registered new interface driver usb-storage
[ 1.801856] USB Mass Storage support registered.
[ 1.802390] scsi 0:0:0:0: Direct-Access Kingston DataTraveler 2.0 1.00
PQ: 0 ANSI: 2
[ 1.830484] sd 0:0:0:0: [sda] 1965056 512-byte hardware sectors (1006 MB)
[ 1.831109] sd 0:0:0:0: [sda] Write Protect is off
[ 1.831111] sd 0:0:0:0: [sda] Mode Sense: 23 00 00 00
[ 1.831113] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 1.833734] sd 0:0:0:0: [sda] 1965056 512-byte hardware sectors (1006 MB)
[ 1.834360] sd 0:0:0:0: [sda] Write Protect is off
[ 1.834363] sd 0:0:0:0: [sda] Mode Sense: 23 00 00 00
[ 1.834364] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 1.834433] sda: sda1 sda2
[ 1.835240] sd 0:0:0:0: [sda] Attached SCSI removable disk
[ 1.835440] usb-storage: device scan complete
[ 2.912741] e100: Intel(R) PRO/100 Network Driver, 3.5.23-k4-NAPI
[ 2.912743] e100: Copyright(c) 1999-2006 Intel Corporation
[ 2.942563] Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI
[ 2.942566] Copyright (c) 1999-2006 Intel Corporation.
[ 2.971978] 8139too Fast Ethernet driver 0.9.28
[ 3.088025] ne2k-pci.c:v1.03 9/22/2003 D. Becker/P. Gortmaker
[ 3.117402] sis900.c: v1.08.10 Apr. 2 2006
[ 3.146609] via-rhine.c:v1.10-LK1.4.3 2007-03-06 Written by Donald Becker
[ 3.235204] r8169 Gigabit Ethernet driver 2.2LK-NAPI loaded
[ 3.235223] ACPI: PCI Interrupt 0000:07:00.0[A] -> GSI 21 (level, low) ->
IRQ 21
[ 3.235828] eth0: RTL8110s at 0xf8894000, 00:18:f8:0b:46:a6, XID 04000000
IRQ 21
[ 3.267764] Linux Tulip driver version 1.1.15-NAPI (Feb 27, 2007)
[ 4.525631] kjournald starting. Commit interval 5 seconds
[ 4.525633] EXT3-fs warning: maximal mount count reached, running e2fsck is
recommended
[ 4.674095] EXT3 FS on dm-0, internal journal
[ 4.674098] EXT3-fs: recovery complete.
[ 4.678221] EXT3-fs: mounted filesystem with ordered data mode.
[ 5.064977] tun: Universal TUN/TAP device driver, 1.6
[ 5.064979] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 5.095188] 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
[ 5.095191] All bugs added by David S. Miller <davem@redhat.com>
[ 5.156387] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 5.188039] IPv4 FIB: Using LC-trie version 0.408
[ 5.227679] e1000e: Intel(R) PRO/1000 Network Driver - 0.3.3.3-k2
[ 5.227681] e1000e: Copyright (c) 1999-2008 Intel Corporation.
[ 5.227724] e1000e 0000:00:19.0: enabling device (0000 -> 0003)
[ 5.227731] ACPI: PCI Interrupt 0000:00:19.0[A] -> GSI 20 (level, low) ->
IRQ 20
[ 5.227742] PCI: Setting latency timer of device 0000:00:19.0 to 64
[ 5.424362] eth1: (PCI Express:2.5GB/s:Width x1) 00:19:d1:71:5f:33
[ 5.424364] eth1: Intel(R) PRO/1000 Network Connection
[ 5.424385] eth1: MAC: 4, PHY: 6, PBA No: ffffff-0ff
[ 5.985995] warning: `zebra' uses 32-bit capabilities (legacy support in use)
[ 6.337111] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 6.580759] ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 21 (level, low) ->
IRQ 21
[ 6.613496] coretemp coretemp.0: Using relative temperature scale!
[ 6.614373] coretemp coretemp.1: Using relative temperature scale!
[ 6.793450] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.03 (30-Apr-2008)
[ 6.794349] iTCO_wdt: Found a ICH8DO TCO device (Version=2, TCOBASE=0x0460)
[ 6.794831] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 7.874067] eth1: Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
--
Denys Fedoryshchenko
Technical Manager
Virtual ISP S.A.L.
next prev parent reply other threads:[~2008-06-16 20:53 UTC|newest]
Thread overview: 33+ messages / expand[flat|nested] mbox.gz Atom feed top
2008-06-16 19:37 packetloss, on e1000e worse than r8169? Denys Fedoryshchenko
2008-06-16 19:48 ` Eric Dumazet
2008-06-16 20:20 ` Denys Fedoryshchenko
2008-06-16 20:23 ` Denys Fedoryshchenko
2008-06-16 20:36 ` Kok, Auke
2008-06-16 20:52 ` Denys Fedoryshchenko [this message]
[not found] ` <20080616204411.M52834@visp.net.lb>
2008-06-16 20:49 ` Kok, Auke
2008-06-16 20:59 ` Denys Fedoryshchenko
2008-06-16 21:13 ` Denys Fedoryshchenko
2008-06-16 21:29 ` Eric Dumazet
2008-06-16 21:41 ` Denys Fedoryshchenko
2008-06-16 21:41 ` Denys Fedoryshchenko
[not found] ` <20080616213419.M212@visp.net.lb>
2008-06-16 21:41 ` Eric Dumazet
2008-06-16 21:44 ` Eric Dumazet
2008-06-16 22:08 ` Denys Fedoryshchenko
2008-06-17 2:17 ` Eric Dumazet
2008-06-17 2:47 ` Denys Fedoryshchenko
2008-06-16 22:08 ` Denys Fedoryshchenko
2008-06-16 23:24 ` Brandeburg, Jesse
2008-06-17 1:53 ` Denys Fedoryshchenko
2008-06-17 6:46 ` Denys Fedoryshchenko
2008-06-17 17:22 ` Denys Fedoryshchenko
2008-06-18 0:58 ` Brandeburg, Jesse
2008-06-17 21:04 ` Denys Fedoryshchenko
2008-06-18 16:50 ` Brandeburg, Jesse
2008-06-18 17:03 ` Denys Fedoryshchenko
2008-06-16 21:17 ` Denys Fedoryshchenko
2008-06-16 21:05 ` Eric Dumazet
2008-06-16 20:15 ` Auke Kok
2008-06-16 20:29 ` Denys Fedoryshchenko
2008-06-16 20:26 ` Francois Romieu
2008-06-16 20:37 ` Waskiewicz Jr, Peter P
2008-06-16 20:42 ` Denys Fedoryshchenko
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20080616205254.M50992@visp.net.lb \
--to=denys@visp.net.lb \
--cc=netdev@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.