[PATCH 0/6] Blackfin Serial Driver updates for 2.6.28

[PATCH 0/6] Blackfin Serial Driver updates for 2.6.28

[Bryan Wu]

Hi Alan,

This is Blackfin serial driver updates:

 - rewrite kgdb over serial supporting
 - some bug fixing

Thanks
-Bryan

[PATCH 1/6] Blackfin Serial Driver: updates kgdb over Blackfin serial driver with kgdb framework

[Bryan Wu]

From: Sonic Zhang <sonic.zhang@analog.com>

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
---
 drivers/serial/bfin_5xx.c |  187 +++++++++++++++++++++-----------------------
 1 files changed, 89 insertions(+), 98 deletions(-)

diff --git a/drivers/serial/bfin_5xx.c b/drivers/serial/bfin_5xx.c
index 569f0e2..d63fad7 100644
--- a/drivers/serial/bfin_5xx.c
+++ b/drivers/serial/bfin_5xx.c
@@ -22,7 +22,8 @@
 #include <linux/tty_flip.h>
 #include <linux/serial_core.h>
 
-#ifdef CONFIG_KGDB_UART
+#if defined(CONFIG_KGDB_SERIAL_CONSOLE) || \
+	defined(CONFIG_KGDB_SERIAL_CONSOLE_MODULE)
 #include <linux/kgdb.h>
 #include <asm/irq_regs.h>
 #endif
@@ -45,6 +46,16 @@
 static struct bfin_serial_port bfin_serial_ports[BFIN_UART_NR_PORTS];
 static int nr_active_ports = ARRAY_SIZE(bfin_serial_resource);
 
+#if defined(CONFIG_KGDB_SERIAL_CONSOLE) || \
+	defined(CONFIG_KGDB_SERIAL_CONSOLE_MODULE)
+
+# ifndef CONFIG_SERIAL_BFIN_PIO
+#  error KGDB only support UART in PIO mode.
+# endif
+
+static int kgdboc_port_line;
+static int kgdboc_break_enabled;
+#endif
 /*
  * Setup for console. Argument comes from the menuconfig
  */
@@ -110,9 +121,7 @@ static void bfin_serial_start_tx(struct uart_port *port)
 static void bfin_serial_stop_rx(struct uart_port *port)
 {
 	struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
-#ifdef CONFIG_KGDB_UART
-	if (uart->port.line != CONFIG_KGDB_UART_PORT)
-#endif
+
 	UART_CLEAR_IER(uart, ERBFI);
 }
 
@@ -123,49 +132,6 @@ static void bfin_serial_enable_ms(struct uart_port *port)
 {
 }
 
-#ifdef CONFIG_KGDB_UART
-static int kgdb_entry_state;
-
-void kgdb_put_debug_char(int chr)
-{
-	struct bfin_serial_port *uart;
-
-	if (CONFIG_KGDB_UART_PORT < 0
-		|| CONFIG_KGDB_UART_PORT >= BFIN_UART_NR_PORTS)
-		uart = &bfin_serial_ports[0];
-	else
-		uart = &bfin_serial_ports[CONFIG_KGDB_UART_PORT];
-
-	while (!(UART_GET_LSR(uart) & THRE)) {
-		SSYNC();
-	}
-
-	UART_CLEAR_DLAB(uart);
-	UART_PUT_CHAR(uart, (unsigned char)chr);
-	SSYNC();
-}
-
-int kgdb_get_debug_char(void)
-{
-	struct bfin_serial_port *uart;
-	unsigned char chr;
-
-	if (CONFIG_KGDB_UART_PORT < 0
-		|| CONFIG_KGDB_UART_PORT >= BFIN_UART_NR_PORTS)
-		uart = &bfin_serial_ports[0];
-	else
-		uart = &bfin_serial_ports[CONFIG_KGDB_UART_PORT];
-
-	while(!(UART_GET_LSR(uart) & DR)) {
-		SSYNC();
-	}
-	UART_CLEAR_DLAB(uart);
-	chr = UART_GET_CHAR(uart);
-	SSYNC();
-
-	return chr;
-}
-#endif
 
 #if ANOMALY_05000363 && defined(CONFIG_SERIAL_BFIN_PIO)
 # define UART_GET_ANOMALY_THRESHOLD(uart)    ((uart)->anomaly_threshold)
@@ -178,7 +144,7 @@ int kgdb_get_debug_char(void)
 #ifdef CONFIG_SERIAL_BFIN_PIO
 static void bfin_serial_rx_chars(struct bfin_serial_port *uart)
 {
-	struct tty_struct *tty = uart->port.info->port.tty;
+	struct tty_struct *tty = NULL;
 	unsigned int status, ch, flg;
 	static struct timeval anomaly_start = { .tv_sec = 0 };
 
@@ -188,27 +154,18 @@ static void bfin_serial_rx_chars(struct bfin_serial_port *uart)
  	ch = UART_GET_CHAR(uart);
  	uart->port.icount.rx++;
 
-#ifdef CONFIG_KGDB_UART
-	if (uart->port.line == CONFIG_KGDB_UART_PORT) {
-		struct pt_regs *regs = get_irq_regs();
-		if (uart->port.cons->index == CONFIG_KGDB_UART_PORT && ch == 0x1) { /* Ctrl + A */
-			kgdb_breakkey_pressed(regs);
-			return;
-		} else if (kgdb_entry_state == 0 && ch == '$') {/* connection from KGDB */
-			kgdb_entry_state = 1;
-		} else if (kgdb_entry_state == 1 && ch == 'q') {
-			kgdb_entry_state = 0;
-			kgdb_breakkey_pressed(regs);
+#if defined(CONFIG_KGDB_SERIAL_CONSOLE) || \
+	defined(CONFIG_KGDB_SERIAL_CONSOLE_MODULE)
+	if (kgdb_connected && kgdboc_port_line == uart->port.line)
+		if (ch == 0x3) {/* Ctrl + C */
+			kgdb_breakpoint();
 			return;
-		} else if (ch == 0x3) {/* Ctrl + C */
-			kgdb_entry_state = 0;
-			kgdb_breakkey_pressed(regs);
-			return;
-		} else {
-			kgdb_entry_state = 0;
 		}
-	}
+
+	if (!uart->port.info || !uart->port.info->tty)
+		return;
 #endif
+	tty = uart->port.info->tty;
 
 	if (ANOMALY_05000363) {
 		/* The BF533 (and BF561) family of processors have a nice anomaly
@@ -630,16 +587,16 @@ static int bfin_serial_startup(struct uart_port *port)
 	uart->rx_dma_timer.expires = jiffies + DMA_RX_FLUSH_JIFFIES;
 	add_timer(&(uart->rx_dma_timer));
 #else
+#if defined(CONFIG_KGDB_SERIAL_CONSOLE) || \
+	defined(CONFIG_KGDB_SERIAL_CONSOLE_MODULE)
+	if (kgdboc_port_line == uart->port.line && kgdboc_break_enabled)
+		kgdboc_break_enabled = 0;
+	else {
+# endif
 	if (request_irq(uart->port.irq, bfin_serial_rx_int, IRQF_DISABLED,
 	     "BFIN_UART_RX", uart)) {
-# ifdef	CONFIG_KGDB_UART
-		if (uart->port.line != CONFIG_KGDB_UART_PORT) {
-# endif
 		printk(KERN_NOTICE "Unable to attach BlackFin UART RX interrupt\n");
 		return -EBUSY;
-# ifdef	CONFIG_KGDB_UART
-		}
-# endif
 	}
 
 	if (request_irq
@@ -685,6 +642,10 @@ static int bfin_serial_startup(struct uart_port *port)
 		}
 	}
 # endif
+#if defined(CONFIG_KGDB_SERIAL_CONSOLE) || \
+	defined(CONFIG_KGDB_SERIAL_CONSOLE_MODULE)
+	}
+# endif
 #endif
 	UART_SET_IER(uart, ERBFI);
 	return 0;
@@ -716,9 +677,6 @@ static void bfin_serial_shutdown(struct uart_port *port)
 		break;
 	};
 #endif
-#ifdef	CONFIG_KGDB_UART
-	if (uart->port.line != CONFIG_KGDB_UART_PORT)
-#endif
 	free_irq(uart->port.irq, uart);
 	free_irq(uart->port.irq+1, uart);
 #endif
@@ -887,6 +845,51 @@ static void bfin_serial_set_ldisc(struct uart_port *port)
 	}
 }
 
+#ifdef CONFIG_CONSOLE_POLL
+static void bfin_serial_poll_put_char(struct uart_port *port, unsigned char chr)
+{
+	struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
+
+	while (!(UART_GET_LSR(uart) & THRE))
+		cpu_relax();
+
+	UART_CLEAR_DLAB(uart);
+	UART_PUT_CHAR(uart, (unsigned char)chr);
+}
+
+static int bfin_serial_poll_get_char(struct uart_port *port)
+{
+	struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
+	unsigned char chr;
+
+	while (!(UART_GET_LSR(uart) & DR))
+		cpu_relax();
+
+	UART_CLEAR_DLAB(uart);
+	chr = UART_GET_CHAR(uart);
+
+	return chr;
+}
+#endif
+
+#if defined(CONFIG_KGDB_SERIAL_CONSOLE) || \
+	defined(CONFIG_KGDB_SERIAL_CONSOLE_MODULE)
+static void bfin_kgdboc_port_shutdown(struct uart_port *port)
+{
+	if (kgdboc_break_enabled) {
+		kgdboc_break_enabled = 0;
+		bfin_serial_shutdown(port);
+	}
+}
+
+static int bfin_kgdboc_port_startup(struct uart_port *port)
+{
+	kgdboc_port_line = port->line;
+	kgdboc_break_enabled = !bfin_serial_startup(port);
+	return 0;
+}
+#endif
+
 static struct uart_ops bfin_serial_pops = {
 	.tx_empty	= bfin_serial_tx_empty,
 	.set_mctrl	= bfin_serial_set_mctrl,
@@ -905,6 +908,15 @@ static struct uart_ops bfin_serial_pops = {
 	.request_port	= bfin_serial_request_port,
 	.config_port	= bfin_serial_config_port,
 	.verify_port	= bfin_serial_verify_port,
+#if defined(CONFIG_KGDB_SERIAL_CONSOLE) || \
+	defined(CONFIG_KGDB_SERIAL_CONSOLE_MODULE)
+	.kgdboc_port_startup	= bfin_kgdboc_port_startup,
+	.kgdboc_port_shutdown	= bfin_kgdboc_port_shutdown,
+#endif
+#ifdef CONFIG_CONSOLE_POLL
+	.poll_put_char	= bfin_serial_poll_put_char,
+	.poll_get_char	= bfin_serial_poll_get_char,
+#endif
 };
 
 static void __init bfin_serial_init_ports(void)
@@ -1076,10 +1088,7 @@ static int __init bfin_serial_rs_console_init(void)
 {
 	bfin_serial_init_ports();
 	register_console(&bfin_serial_console);
-#ifdef CONFIG_KGDB_UART
-	kgdb_entry_state = 0;
-	init_kgdb_uart();
-#endif
+
 	return 0;
 }
 console_initcall(bfin_serial_rs_console_init);
@@ -1235,10 +1244,6 @@ static struct platform_driver bfin_serial_driver = {
 static int __init bfin_serial_init(void)
 {
 	int ret;
-#ifdef CONFIG_KGDB_UART
-	struct bfin_serial_port *uart = &bfin_serial_ports[CONFIG_KGDB_UART_PORT];
-	struct ktermios t;
-#endif
 
 	pr_info("Serial: Blackfin serial driver\n");
 
@@ -1252,21 +1257,6 @@ static int __init bfin_serial_init(void)
 			uart_unregister_driver(&bfin_serial_reg);
 		}
 	}
-#ifdef CONFIG_KGDB_UART
-	if (uart->port.cons->index != CONFIG_KGDB_UART_PORT) {
-		request_irq(uart->port.irq, bfin_serial_rx_int,
-			IRQF_DISABLED, "BFIN_UART_RX", uart);
-		pr_info("Request irq for kgdb uart port\n");
-		UART_SET_IER(uart, ERBFI);
-		SSYNC();
-		t.c_cflag = CS8|B57600;
-		t.c_iflag = 0;
-		t.c_oflag = 0;
-		t.c_lflag = ICANON;
-		t.c_line = CONFIG_KGDB_UART_PORT;
-		bfin_serial_set_termios(&uart->port, &t, &t);
-	}
-#endif
 	return ret;
 }
 
@@ -1276,6 +1266,7 @@ static void __exit bfin_serial_exit(void)
 	uart_unregister_driver(&bfin_serial_reg);
 }
 
+
 module_init(bfin_serial_init);
 module_exit(bfin_serial_exit);
 
-- 
1.5.6

[PATCH 2/6] Blackfin Serial Driver: Add a debug function to serial driver.

[Bryan Wu]

From: Graf Yang <graf.yang@analog.com>

Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
---
 drivers/serial/bfin_5xx.c |   47 ++++++++++++++++++++++++++++++++++++++++++++-
 1 files changed, 46 insertions(+), 1 deletions(-)

diff --git a/drivers/serial/bfin_5xx.c b/drivers/serial/bfin_5xx.c
index d63fad7..aea3a53 100644
--- a/drivers/serial/bfin_5xx.c
+++ b/drivers/serial/bfin_5xx.c
@@ -21,6 +21,7 @@
 #include <linux/tty.h>
 #include <linux/tty_flip.h>
 #include <linux/serial_core.h>
+#include <stdarg.h>
 
 #if defined(CONFIG_KGDB_SERIAL_CONSOLE) || \
 	defined(CONFIG_KGDB_SERIAL_CONSOLE_MODULE)
@@ -1106,7 +1107,8 @@ static __init void early_serial_putc(struct uart_port *port, int ch)
 	struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
 
 	while ((!(UART_GET_LSR(uart) & THRE)) && --timeout)
-		cpu_relax();
+		barrier();
+
 	UART_PUT_CHAR(uart, ch);
 }
 
@@ -1155,6 +1157,49 @@ struct console __init *bfin_earlyserial_init(unsigned int port,
 
 #endif /* CONFIG_SERIAL_BFIN_CONSOLE */
 
+#ifdef CONFIG_DEBUG_KERNEL
+void bfin_serial_debug(const char *fmt, ...)
+{
+	struct bfin_serial_port *uart = &bfin_serial_ports[0];
+	unsigned short status, tmp;
+	int flags, i, count;
+	char buf[128];
+	va_list ap;
+
+	if (bfin_serial_console.index < 0)
+		return;		/* Too early. */
+
+	va_start(ap, fmt);
+	vsprintf(buf, fmt, ap);
+	va_end(ap);
+	count = strlen(buf);
+
+	spin_lock_irqsave(&uart->port.lock, flags);
+
+	for (i = 0; i < count; i++) {
+		do {
+			status = UART_GET_LSR(uart);
+		} while (!(status & THRE));
+
+#ifndef CONFIG_BF54x
+		tmp = UART_GET_LCR(uart);
+		tmp &= ~DLAB;
+		UART_PUT_LCR(uart, tmp);
+#endif
+		UART_PUT_CHAR(uart, buf[i]);
+		if (buf[i] == '\n') {
+			do {
+				status = UART_GET_LSR(uart);
+			} while (!(status & THRE));
+			UART_PUT_CHAR(uart, '\r');
+		}
+	}
+
+	spin_unlock_irqrestore(&uart->port.lock, flags);
+}
+EXPORT_SYMBOL(bfin_serial_debug);
+#endif
+
 static struct uart_driver bfin_serial_reg = {
 	.owner			= THIS_MODULE,
 	.driver_name		= "bfin-uart",
-- 
1.5.6

Re: [PATCH 2/6] Blackfin Serial Driver: Add a debug function to serial driver.

[Alan Cox]

> -		cpu_relax();
> +		barrier();
> +

Seems to be an odd unrelated change ?

Re: [PATCH 2/6] Blackfin Serial Driver: Add a debug function to serial driver.

[Alan Cox]

> -		cpu_relax();
> +		barrier();
> +

Seems to be an odd unrelated change ?

Re: [PATCH 2/6] Blackfin Serial Driver: Add a debug function to serial driver.

[gyang]

Hi, Alan,

We are making a SMP like patch to blackfin, cpu_relax() is replaced by a
data cache flush function which will count it to a per-cpu counter.
If this serial function is called too early, the per-cpu data area have
not been initialized, this call will cause crash.
So we'd like to use barrier() instead of cpu_relax().

BRs,
Graf

在 2008-10-14二的 14:27 +0100，Alan Cox写道：
> > -		cpu_relax();
> > +		barrier();
> > +
> 
> Seems to be an odd unrelated change ?
--
To unsubscribe from this list: send the line "unsubscribe linux-serial" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH 2/6] Blackfin Serial Driver: Add a debug function to serial driver.

[gyang]

Hi, Alan,

We are making a SMP like patch to blackfin, cpu_relax() is replaced by a
data cache flush function which will count it to a per-cpu counter.
If this serial function is called too early, the per-cpu data area have
not been initialized, this call will cause crash.
So we'd like to use barrier() instead of cpu_relax().

BRs,
Graf

在 2008-10-14二的 14:27 +0100，Alan Cox写道：
> > -		cpu_relax();
> > +		barrier();
> > +
> 
> Seems to be an odd unrelated change ?

Re: [PATCH 2/6] Blackfin Serial Driver: Add a debug function to serial driver.

[Alan Cox]

On Wed, Oct 15, 2008 at 10:23:41AM +0800, gyang wrote:
> We are making a SMP like patch to blackfin, cpu_relax() is replaced by a
> data cache flush function which will count it to a per-cpu counter.
> If this serial function is called too early, the per-cpu data area have
> not been initialized, this call will cause crash.
> So we'd like to use barrier() instead of cpu_relax().

Can you split that out as a separate change and include the explanation in
the patch then.

Thanks
Alan

Re: [PATCH 2/6] Blackfin Serial Driver: Add a debug function to serial driver.

[Bryan Wu]

On Wed, Oct 15, 2008 at 4:38 PM, Alan Cox <alan@redhat.com> wrote:
> On Wed, Oct 15, 2008 at 10:23:41AM +0800, gyang wrote:
>> We are making a SMP like patch to blackfin, cpu_relax() is replaced by a
>> data cache flush function which will count it to a per-cpu counter.
>> If this serial function is called too early, the per-cpu data area have
>> not been initialized, this call will cause crash.
>> So we'd like to use barrier() instead of cpu_relax().
>
> Can you split that out as a separate change and include the explanation in
> the patch then.
>
> Thanks
> Alan
>

I'll handle this and will resend the whole blackfin serial driver
patches again as well as Sonic updates some bug fixing recently.

Thanks
-Bryan

[PATCH 3/6] Blackfin Serial Driver: fix bug - SIR driver stop receiving randomly

[Bryan Wu]

From: Graf Yang <graf.yang@analog.com>

Bug description:
The IRDA receiver may can't receiving any more after processed some signals.

To duplicate this issue is put three IRDA devices together, one blackfin,
two none blackfin, they will detect each other. Let one none blackfin devices
irdaping the blackfin devices, when it stopped print out ping information,
it is the time that blackfin stoped receiving, the time is random.

The related register bit is OK, the other devices is sending data continuously.
But no interrupt come.

Fixing:
I tried Michael's suggestion that request the UARTx error interrupt, and reset
the IRDA when found FE error. This method helps much, but it can't completely
avoid stop.

Reset the IRDA before every time sending the data is more safe.

Cc: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
---
 drivers/serial/bfin_5xx.c |   24 ++++++++++++++++++++++++
 1 files changed, 24 insertions(+), 0 deletions(-)

diff --git a/drivers/serial/bfin_5xx.c b/drivers/serial/bfin_5xx.c
index aea3a53..3cc7b98 100644
--- a/drivers/serial/bfin_5xx.c
+++ b/drivers/serial/bfin_5xx.c
@@ -74,6 +74,8 @@ static void bfin_serial_tx_chars(struct bfin_serial_port *uart);
 
 static void bfin_serial_mctrl_check(struct bfin_serial_port *uart);
 
+static void bfin_serial_reset_irda(struct uart_port *port);
+
 /*
  * interrupts are disabled on entry
  */
@@ -106,6 +108,14 @@ static void bfin_serial_stop_tx(struct uart_port *port)
 static void bfin_serial_start_tx(struct uart_port *port)
 {
 	struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
+	struct tty_struct *tty = uart->port.info->port.tty;
+
+	/*
+	 * To avoid losting RX interrupt, we reset IR function
+	 * before sending data.
+	 */
+	if (tty->termios->c_line == N_IRDA)
+		bfin_serial_reset_irda(port);
 
 #ifdef CONFIG_SERIAL_BFIN_DMA
 	if (uart->tx_done)
@@ -891,6 +901,20 @@ static int bfin_kgdboc_port_startup(struct uart_port *port)
 }
 #endif
 
+static void bfin_serial_reset_irda(struct uart_port *port)
+{
+	int line = port->line;
+	unsigned short val;
+
+	val = UART_GET_GCTL(&bfin_serial_ports[line]);
+	val &= ~(IREN | RPOLC);
+	UART_PUT_GCTL(&bfin_serial_ports[line], val);
+	SSYNC();
+	val |= (IREN | RPOLC);
+	UART_PUT_GCTL(&bfin_serial_ports[line], val);
+	SSYNC();
+}
+
 static struct uart_ops bfin_serial_pops = {
 	.tx_empty	= bfin_serial_tx_empty,
 	.set_mctrl	= bfin_serial_set_mctrl,
-- 
1.5.6

[PATCH 4/6] Blackfin Serial Driver: Clean serial console and early prink code`

[Bryan Wu]

From: Sonic Zhang <sonic.zhang@analog.com>

Singed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
---
 drivers/serial/bfin_5xx.c |   16 ++++------------
 1 files changed, 4 insertions(+), 12 deletions(-)

diff --git a/drivers/serial/bfin_5xx.c b/drivers/serial/bfin_5xx.c
index 3cc7b98..44a0855 100644
--- a/drivers/serial/bfin_5xx.c
+++ b/drivers/serial/bfin_5xx.c
@@ -987,7 +987,7 @@ static void __init bfin_serial_init_ports(void)
 
 }
 
-#ifdef CONFIG_SERIAL_BFIN_CONSOLE
+#if defined(CONFIG_SERIAL_BFIN_CONSOLE) || defined(CONFIG_EARLY_PRINTK)
 /*
  * If the port was already initialised (eg, by a boot loader),
  * try to determine the current setup.
@@ -1031,24 +1031,20 @@ bfin_serial_console_get_options(struct bfin_serial_port *uart, int *baud,
 	}
 	pr_debug("%s:baud = %d, parity = %c, bits= %d\n", __func__, *baud, *parity, *bits);
 }
-#endif
 
-#if defined(CONFIG_SERIAL_BFIN_CONSOLE) || defined(CONFIG_EARLY_PRINTK)
 static struct uart_driver bfin_serial_reg;
 
 static int __init
 bfin_serial_console_setup(struct console *co, char *options)
 {
 	struct bfin_serial_port *uart;
-# ifdef CONFIG_SERIAL_BFIN_CONSOLE
 	int baud = 57600;
 	int bits = 8;
 	int parity = 'n';
-#  ifdef CONFIG_SERIAL_BFIN_CTSRTS
+# ifdef CONFIG_SERIAL_BFIN_CTSRTS
 	int flow = 'r';
-#  else
+# else
 	int flow = 'n';
-#  endif
 # endif
 
 	/*
@@ -1060,16 +1056,12 @@ bfin_serial_console_setup(struct console *co, char *options)
 		co->index = 0;
 	uart = &bfin_serial_ports[co->index];
 
-# ifdef CONFIG_SERIAL_BFIN_CONSOLE
 	if (options)
 		uart_parse_options(options, &baud, &parity, &bits, &flow);
 	else
 		bfin_serial_console_get_options(uart, &baud, &parity, &bits);
 
 	return uart_set_options(&uart->port, co, baud, parity, bits, flow);
-# else
-	return 0;
-# endif
 }
 #endif /* defined (CONFIG_SERIAL_BFIN_CONSOLE) ||
 				 defined (CONFIG_EARLY_PRINTK) */
@@ -1179,7 +1171,7 @@ struct console __init *bfin_earlyserial_init(unsigned int port,
 	return &bfin_early_serial_console;
 }
 
-#endif /* CONFIG_SERIAL_BFIN_CONSOLE */
+#endif /* CONFIG_EARLY_PRINTK */
 
 #ifdef CONFIG_DEBUG_KERNEL
 void bfin_serial_debug(const char *fmt, ...)
-- 
1.5.6

[PATCH 5/6] Blackfin Serial Driver: Fix bug - BF527-EZKIT unable to receive large files over UART in DMA mode

[Bryan Wu]

From: Sonic Zhang <sonic.zhang@analog.com>

Add spin_lock_irqsave() when receive and transfer data.

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
---
 drivers/serial/bfin_5xx.c |   11 ++++++++---
 1 files changed, 8 insertions(+), 3 deletions(-)

diff --git a/drivers/serial/bfin_5xx.c b/drivers/serial/bfin_5xx.c
index 44a0855..82854d7 100644
--- a/drivers/serial/bfin_5xx.c
+++ b/drivers/serial/bfin_5xx.c
@@ -82,7 +82,9 @@ static void bfin_serial_reset_irda(struct uart_port *port);
 static void bfin_serial_stop_tx(struct uart_port *port)
 {
 	struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
+#ifdef CONFIG_SERIAL_BFIN_DMA
 	struct circ_buf *xmit = &uart->port.info->xmit;
+#endif
 
 	while (!(UART_GET_LSR(uart) & TEMT))
 		cpu_relax();
@@ -413,7 +415,9 @@ static void bfin_serial_dma_rx_chars(struct bfin_serial_port *uart)
 
 void bfin_serial_rx_dma_timeout(struct bfin_serial_port *uart)
 {
-	int x_pos, pos;
+	int x_pos, pos, flags;
+
+	spin_lock_irqsave(&uart->port.lock, flags);
 
 	uart->rx_dma_nrows = get_dma_curr_ycount(uart->rx_dma_channel);
 	x_pos = get_dma_curr_xcount(uart->rx_dma_channel);
@@ -431,6 +435,8 @@ void bfin_serial_rx_dma_timeout(struct bfin_serial_port *uart)
 		uart->rx_dma_buf.tail = uart->rx_dma_buf.head;
 	}
 
+	spin_unlock_irqrestore(&uart->port.lock, flags);
+
 	mod_timer(&(uart->rx_dma_timer), jiffies + DMA_RX_FLUSH_JIFFIES);
 }
 
@@ -465,10 +471,9 @@ static irqreturn_t bfin_serial_dma_rx_int(int irq, void *dev_id)
 	spin_lock(&uart->port.lock);
 	irqstat = get_dma_curr_irqstat(uart->rx_dma_channel);
 	clear_dma_irqstat(uart->rx_dma_channel);
+	bfin_serial_dma_rx_chars(uart);
 	spin_unlock(&uart->port.lock);
 
-	mod_timer(&(uart->rx_dma_timer), jiffies);
-
 	return IRQ_HANDLED;
 }
 #endif
-- 
1.5.6

[PATCH 6/6] Blackfin Serial Driver: Remove BI status for known_good_char

[Bryan Wu]

From: Sonic Zhang <sonic.zhang@analog.com>

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
---
 drivers/serial/bfin_5xx.c |    1 +
 1 files changed, 1 insertions(+), 0 deletions(-)

diff --git a/drivers/serial/bfin_5xx.c b/drivers/serial/bfin_5xx.c
index 82854d7..350bfc4 100644
--- a/drivers/serial/bfin_5xx.c
+++ b/drivers/serial/bfin_5xx.c
@@ -220,6 +220,7 @@ static void bfin_serial_rx_chars(struct bfin_serial_port *uart)
 			return;
 
  known_good_char:
+			status &= ~BI;
 			anomaly_start.tv_sec = 0;
 		}
 	}
-- 
1.5.6

Re: [PATCH 0/6] Blackfin Serial Driver updates for 2.6.28

[Alan Cox]

On Mon, 13 Oct 2008 17:46:19 +0800
Bryan Wu <cooloney@kernel.org> wrote:

> 
> Hi Alan,
> 
> This is Blackfin serial driver updates:
> 
>  - rewrite kgdb over serial supporting
>  - some bug fixing

Queued for once the current tty patches have appeared in Linus tree.