[PATCH 0/4] Few patches needed to support QE USB on MPC8360E-{MDS,RDK} boards

[PATCH 0/4] Few patches needed to support QE USB on MPC8360E-{MDS,RDK} boards

[Anton Vorontsov]

Hi Kumar,

I'm resending the QE USB patches, the old ones started to cause
rejects.

Could you apply them for 2.6.28? Especially the first patch, since
it is holding the FHCI driver. I still hope that Greg would apply
the driver post -rc1. ;-)


Thanks!

-- 
Anton Vorontsov
email: cbouatmailru@gmail.com
irc://irc.freenode.net/bd2

[PATCH 1/4] powerpc/QE: implement QE Pin Multiplexing API

[Anton Vorontsov]

With this API we're able to set a QE pin to the GPIO mode or a dedicated
peripheral function.

The API relies on the fact that QE gpio controllers are registered. If
they aren't, the API won't work (gracefully though).

There is one caveat though: if anybody occupied the node->data before us,
or overwrote it, then bad things will happen. Luckily this is all in the
platform code that we fully control, so this should never happen.

I could implement more checks (for example we could create a list of
successfully registered QE controllers, and compare the node->data in the
qe_pin_request()), but this is unneeded if nobody is going to do silly
things behind our back.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
---
 arch/powerpc/include/asm/qe.h     |    9 ++
 arch/powerpc/sysdev/qe_lib/gpio.c |  195 +++++++++++++++++++++++++++++++++++++
 2 files changed, 204 insertions(+), 0 deletions(-)

diff --git a/arch/powerpc/include/asm/qe.h b/arch/powerpc/include/asm/qe.h
index edee15d..31ddbc9 100644
--- a/arch/powerpc/include/asm/qe.h
+++ b/arch/powerpc/include/asm/qe.h
@@ -112,6 +112,15 @@ extern int par_io_config_pin(u8 port, u8 pin, int dir, int open_drain,
 			     int assignment, int has_irq);
 extern int par_io_data_set(u8 port, u8 pin, u8 val);
 
+/*
+ * Pin multiplexing functions.
+ */
+struct qe_pin;
+extern struct qe_pin *qe_pin_request(struct device_node *np, int index);
+extern void qe_pin_free(struct qe_pin *qe_pin);
+extern void qe_pin_set_gpio(struct qe_pin *qe_pin);
+extern void qe_pin_set_dedicated(struct qe_pin *pin);
+
 /* QE internal API */
 int qe_issue_cmd(u32 cmd, u32 device, u8 mcn_protocol, u32 cmd_input);
 enum qe_clock qe_clock_source(const char *source);
diff --git a/arch/powerpc/sysdev/qe_lib/gpio.c b/arch/powerpc/sysdev/qe_lib/gpio.c
index 8e5a0bc..7f10b18 100644
--- a/arch/powerpc/sysdev/qe_lib/gpio.c
+++ b/arch/powerpc/sysdev/qe_lib/gpio.c
@@ -14,6 +14,7 @@
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/spinlock.h>
+#include <linux/err.h>
 #include <linux/io.h>
 #include <linux/of.h>
 #include <linux/of_gpio.h>
@@ -24,8 +25,14 @@ struct qe_gpio_chip {
 	struct of_mm_gpio_chip mm_gc;
 	spinlock_t lock;
 
+	unsigned long pin_flags[QE_PIO_PINS];
+#define QE_PIN_REQUESTED 0
+
 	/* shadowed data register to clear/set bits safely */
 	u32 cpdata;
+
+	/* saved_regs used to restore dedicated functions */
+	struct qe_pio_regs saved_regs;
 };
 
 static inline struct qe_gpio_chip *
@@ -40,6 +47,12 @@ static void qe_gpio_save_regs(struct of_mm_gpio_chip *mm_gc)
 	struct qe_pio_regs __iomem *regs = mm_gc->regs;
 
 	qe_gc->cpdata = in_be32(&regs->cpdata);
+	qe_gc->saved_regs.cpdata = qe_gc->cpdata;
+	qe_gc->saved_regs.cpdir1 = in_be32(&regs->cpdir1);
+	qe_gc->saved_regs.cpdir2 = in_be32(&regs->cpdir2);
+	qe_gc->saved_regs.cppar1 = in_be32(&regs->cppar1);
+	qe_gc->saved_regs.cppar2 = in_be32(&regs->cppar2);
+	qe_gc->saved_regs.cpodr = in_be32(&regs->cpodr);
 }
 
 static int qe_gpio_get(struct gpio_chip *gc, unsigned int gpio)
@@ -103,6 +116,188 @@ static int qe_gpio_dir_out(struct gpio_chip *gc, unsigned int gpio, int val)
 	return 0;
 }
 
+struct qe_pin {
+	/*
+	 * The qe_gpio_chip name is unfortunate, we should change that to
+	 * something like qe_pio_controller. Someday.
+	 */
+	struct qe_gpio_chip *controller;
+	int num;
+};
+
+/**
+ * qe_pin_request - Request a QE pin
+ * @np:		device node to get a pin from
+ * @index:	index of a pin in the device tree
+ * Context:	non-atomic
+ *
+ * This function return qe_pin so that you could use it with the rest of
+ * the QE Pin Multiplexing API.
+ */
+struct qe_pin *qe_pin_request(struct device_node *np, int index)
+{
+	struct qe_pin *qe_pin;
+	struct device_node *gc;
+	struct of_gpio_chip *of_gc = NULL;
+	struct of_mm_gpio_chip *mm_gc;
+	struct qe_gpio_chip *qe_gc;
+	int err;
+	int size;
+	const void *gpio_spec;
+	const u32 *gpio_cells;
+	unsigned long flags;
+
+	qe_pin = kzalloc(sizeof(*qe_pin), GFP_KERNEL);
+	if (!qe_pin) {
+		pr_debug("%s: can't allocate memory\n", __func__);
+		return ERR_PTR(-ENOMEM);
+	}
+
+	err = of_parse_phandles_with_args(np, "gpios", "#gpio-cells", index,
+					  &gc, &gpio_spec);
+	if (err) {
+		pr_debug("%s: can't parse gpios property\n", __func__);
+		goto err0;
+	}
+
+	if (!of_device_is_compatible(gc, "fsl,mpc8323-qe-pario-bank")) {
+		pr_debug("%s: tried to get a non-qe pin\n", __func__);
+		err = -EINVAL;
+		goto err1;
+	}
+
+	of_gc = gc->data;
+	if (!of_gc) {
+		pr_debug("%s: gpio controller %s isn't registered\n",
+			 np->full_name, gc->full_name);
+		err = -ENODEV;
+		goto err1;
+	}
+
+	gpio_cells = of_get_property(gc, "#gpio-cells", &size);
+	if (!gpio_cells || size != sizeof(*gpio_cells) ||
+			*gpio_cells != of_gc->gpio_cells) {
+		pr_debug("%s: wrong #gpio-cells for %s\n",
+			 np->full_name, gc->full_name);
+		err = -EINVAL;
+		goto err1;
+	}
+
+	err = of_gc->xlate(of_gc, np, gpio_spec);
+	if (err < 0)
+		goto err1;
+
+	mm_gc = to_of_mm_gpio_chip(&of_gc->gc);
+	qe_gc = to_qe_gpio_chip(mm_gc);
+
+	spin_lock_irqsave(&qe_gc->lock, flags);
+
+	if (test_and_set_bit(QE_PIN_REQUESTED, &qe_gc->pin_flags[err]) == 0) {
+		qe_pin->controller = qe_gc;
+		qe_pin->num = err;
+		err = 0;
+	} else {
+		err = -EBUSY;
+	}
+
+	spin_unlock_irqrestore(&qe_gc->lock, flags);
+
+	if (!err)
+		return qe_pin;
+err1:
+	of_node_put(gc);
+err0:
+	kfree(qe_pin);
+	pr_debug("%s failed with status %d\n", __func__, err);
+	return ERR_PTR(err);
+}
+EXPORT_SYMBOL(qe_pin_request);
+
+/**
+ * qe_pin_free - Free a pin
+ * @qe_pin:	pointer to the qe_pin structure
+ * Context:	any
+ *
+ * This function frees the qe_pin structure and makes a pin available
+ * for further qe_pin_request() calls.
+ */
+void qe_pin_free(struct qe_pin *qe_pin)
+{
+	struct qe_gpio_chip *qe_gc = qe_pin->controller;
+	unsigned long flags;
+	const int pin = qe_pin->num;
+
+	spin_lock_irqsave(&qe_gc->lock, flags);
+	test_and_clear_bit(QE_PIN_REQUESTED, &qe_gc->pin_flags[pin]);
+	spin_unlock_irqrestore(&qe_gc->lock, flags);
+
+	kfree(qe_pin);
+}
+EXPORT_SYMBOL(qe_pin_free);
+
+/**
+ * qe_pin_set_dedicated - Revert a pin to a dedicated peripheral function mode
+ * @qe_pin:	pointer to the qe_pin structure
+ * Context:	any
+ *
+ * This function resets a pin to a dedicated peripheral function that
+ * has been set up by the firmware.
+ */
+void qe_pin_set_dedicated(struct qe_pin *qe_pin)
+{
+	struct qe_gpio_chip *qe_gc = qe_pin->controller;
+	struct qe_pio_regs __iomem *regs = qe_gc->mm_gc.regs;
+	struct qe_pio_regs *sregs = &qe_gc->saved_regs;
+	int pin = qe_pin->num;
+	u32 mask1 = 1 << (QE_PIO_PINS - (pin + 1));
+	u32 mask2 = 0x3 << (QE_PIO_PINS - (pin % (QE_PIO_PINS / 2) + 1) * 2);
+	bool second_reg = pin > (QE_PIO_PINS / 2) - 1;
+	unsigned long flags;
+
+	spin_lock_irqsave(&qe_gc->lock, flags);
+
+	if (second_reg) {
+		clrsetbits_be32(&regs->cpdir2, mask2, sregs->cpdir2 & mask2);
+		clrsetbits_be32(&regs->cppar2, mask2, sregs->cppar2 & mask2);
+	} else {
+		clrsetbits_be32(&regs->cpdir1, mask2, sregs->cpdir1 & mask2);
+		clrsetbits_be32(&regs->cppar1, mask2, sregs->cppar1 & mask2);
+	}
+
+	if (sregs->cpdata & mask1)
+		qe_gc->cpdata |= mask1;
+	else
+		qe_gc->cpdata &= ~mask1;
+
+	out_be32(&regs->cpdata, qe_gc->cpdata);
+	clrsetbits_be32(&regs->cpodr, mask1, sregs->cpodr & mask1);
+
+	spin_unlock_irqrestore(&qe_gc->lock, flags);
+}
+EXPORT_SYMBOL(qe_pin_set_dedicated);
+
+/**
+ * qe_pin_set_gpio - Set a pin to the GPIO mode
+ * @qe_pin:	pointer to the qe_pin structure
+ * Context:	any
+ *
+ * This function sets a pin to the GPIO mode.
+ */
+void qe_pin_set_gpio(struct qe_pin *qe_pin)
+{
+	struct qe_gpio_chip *qe_gc = qe_pin->controller;
+	struct qe_pio_regs __iomem *regs = qe_gc->mm_gc.regs;
+	unsigned long flags;
+
+	spin_lock_irqsave(&qe_gc->lock, flags);
+
+	/* Let's make it input by default, GPIO API is able to change that. */
+	__par_io_config_pin(regs, qe_pin->num, QE_PIO_DIR_IN, 0, 0, 0);
+
+	spin_unlock_irqrestore(&qe_gc->lock, flags);
+}
+EXPORT_SYMBOL(qe_pin_set_gpio);
+
 static int __init qe_add_gpiochips(void)
 {
 	struct device_node *np;
-- 
1.5.6.3

[PATCH 2/4] powerpc: add driver for simple GPIO banks

[Anton Vorontsov]

The driver supports very simple GPIO controllers, that is, when a
controller provides just a 'data' register. Such controllers may be
found in various BCSRs (Board's FPGAs used to control board's
switches, LEDs, chip-selects, Ethernet/USB PHY power, etc).

So far we support only 1-byte GPIO banks. Support for other widths may
be implemented when/if needed.

p.s.
To avoid "made up" compatible entries (like compatible = "simple-gpio"),
boards must call the simple_gpiochip_init() to pass the compatible
string.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
---
 Documentation/powerpc/dts-bindings/fsl/board.txt |   30 ++++
 arch/powerpc/platforms/Kconfig                   |   10 ++
 arch/powerpc/sysdev/Makefile                     |    1 +
 arch/powerpc/sysdev/simple_gpio.c                |  156 ++++++++++++++++++++++
 arch/powerpc/sysdev/simple_gpio.h                |   13 ++
 5 files changed, 210 insertions(+), 0 deletions(-)
 create mode 100644 arch/powerpc/sysdev/simple_gpio.c
 create mode 100644 arch/powerpc/sysdev/simple_gpio.h

diff --git a/Documentation/powerpc/dts-bindings/fsl/board.txt b/Documentation/powerpc/dts-bindings/fsl/board.txt
index 74ae6f1..e97877f 100644
--- a/Documentation/powerpc/dts-bindings/fsl/board.txt
+++ b/Documentation/powerpc/dts-bindings/fsl/board.txt
@@ -27,3 +27,33 @@ Example (MPC8610HPCD):
 		compatible = "fsl,fpga-pixis";
 		reg = <0xe8000000 32>;
 	};
+
+* Freescale BCSR GPIO banks
+
+Some BCSR registers act as simple GPIO controllers, each such
+register can be represented by the gpio-controller node.
+
+Required properities:
+- compatible : Should be "fsl,<board>-bcsr-gpio";
+- reg : Should contain the address and the lenght of the GPIO bank
+  register;
+- #gpio-cells : Should be two. The first cell is the pin number and the
+  second cell is used to specify optional paramters (currently unused);
+- gpio-controller : Marks the port as GPIO controller.
+
+Example:
+
+	bcsr@1,0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		device_type = "board-control";
+		reg = <1 0 0x8000>;
+		ranges = <0 1 0 0x8000>;
+
+		bcsr13: gpio-controller@d {
+			#gpio-cells = <2>;
+			compatible = "fsl,mpc8360mds-bcsr-gpio";
+			reg = <0xd 1>;
+			gpio-controller;
+		};
+	};
diff --git a/arch/powerpc/platforms/Kconfig b/arch/powerpc/platforms/Kconfig
index 47e956c..63780c8 100644
--- a/arch/powerpc/platforms/Kconfig
+++ b/arch/powerpc/platforms/Kconfig
@@ -312,4 +312,14 @@ config MPC8xxx_GPIO
 	  Say Y here if you're going to use hardware that connects to the
 	  MPC831x/834x/837x/8572/8610 GPIOs.
 
+config SIMPLE_GPIO
+	bool "Support for simple, memory-mapped GPIO controllers"
+	depends on PPC
+	select GENERIC_GPIO
+	select ARCH_REQUIRE_GPIOLIB
+	help
+	  Say Y here to support simple, memory-mapped GPIO controllers.
+	  These are usually BCSRs used to control board's switches, LEDs,
+	  chip-selects, Ethernet/USB PHY's power and various other small
+	  on-board peripherals.
 endmenu
diff --git a/arch/powerpc/sysdev/Makefile b/arch/powerpc/sysdev/Makefile
index a44709a..ee2ddae 100644
--- a/arch/powerpc/sysdev/Makefile
+++ b/arch/powerpc/sysdev/Makefile
@@ -34,6 +34,7 @@ obj-$(CONFIG_4xx)		+= uic.o
 obj-$(CONFIG_4xx_SOC)		+= ppc4xx_soc.o
 obj-$(CONFIG_XILINX_VIRTEX)	+= xilinx_intc.o
 obj-$(CONFIG_OF_RTC)		+= of_rtc.o
+obj-$(CONFIG_SIMPLE_GPIO)	+= simple_gpio.o
 ifeq ($(CONFIG_PCI),y)
 obj-$(CONFIG_4xx)		+= ppc4xx_pci.o
 endif
diff --git a/arch/powerpc/sysdev/simple_gpio.c b/arch/powerpc/sysdev/simple_gpio.c
new file mode 100644
index 0000000..d62c85a
--- /dev/null
+++ b/arch/powerpc/sysdev/simple_gpio.c
@@ -0,0 +1,156 @@
+/*
+ * Simple Memory-Mapped GPIOs
+ *
+ * Copyright (c) MontaVista Software, Inc. 2008.
+ *
+ * Author: Anton Vorontsov <avorontsov@ru.mvista.com>
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/spinlock.h>
+#include <linux/types.h>
+#include <linux/ioport.h>
+#include <linux/io.h>
+#include <linux/of.h>
+#include <linux/of_gpio.h>
+#include <linux/gpio.h>
+#include <asm/prom.h>
+#include "simple_gpio.h"
+
+struct u8_gpio_chip {
+	struct of_mm_gpio_chip mm_gc;
+	spinlock_t lock;
+
+	/* shadowed data register to clear/set bits safely */
+	u8 data;
+};
+
+static struct u8_gpio_chip *to_u8_gpio_chip(struct of_mm_gpio_chip *mm_gc)
+{
+	return container_of(mm_gc, struct u8_gpio_chip, mm_gc);
+}
+
+static u8 u8_pin2mask(unsigned int pin)
+{
+	return 1 << (8 - 1 - pin);
+}
+
+static int u8_gpio_get(struct gpio_chip *gc, unsigned int gpio)
+{
+	struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
+
+	return in_8(mm_gc->regs) & u8_pin2mask(gpio);
+}
+
+static void u8_gpio_set(struct gpio_chip *gc, unsigned int gpio, int val)
+{
+	struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
+	struct u8_gpio_chip *u8_gc = to_u8_gpio_chip(mm_gc);
+	unsigned long flags;
+
+	spin_lock_irqsave(&u8_gc->lock, flags);
+
+	if (val)
+		u8_gc->data |= u8_pin2mask(gpio);
+	else
+		u8_gc->data &= ~u8_pin2mask(gpio);
+
+	out_8(mm_gc->regs, u8_gc->data);
+
+	spin_unlock_irqrestore(&u8_gc->lock, flags);
+}
+
+static int u8_gpio_dir_in(struct gpio_chip *gc, unsigned int gpio)
+{
+	return 0;
+}
+
+static int u8_gpio_dir_out(struct gpio_chip *gc, unsigned int gpio, int val)
+{
+	u8_gpio_set(gc, gpio, val);
+	return 0;
+}
+
+static void u8_gpio_save_regs(struct of_mm_gpio_chip *mm_gc)
+{
+	struct u8_gpio_chip *u8_gc = to_u8_gpio_chip(mm_gc);
+
+	u8_gc->data = in_8(mm_gc->regs);
+}
+
+static int __init u8_simple_gpiochip_add(struct device_node *np)
+{
+	int ret;
+	struct u8_gpio_chip *u8_gc;
+	struct of_mm_gpio_chip *mm_gc;
+	struct of_gpio_chip *of_gc;
+	struct gpio_chip *gc;
+
+	u8_gc = kzalloc(sizeof(*u8_gc), GFP_KERNEL);
+	if (!u8_gc)
+		return -ENOMEM;
+
+	spin_lock_init(&u8_gc->lock);
+
+	mm_gc = &u8_gc->mm_gc;
+	of_gc = &mm_gc->of_gc;
+	gc = &of_gc->gc;
+
+	mm_gc->save_regs = u8_gpio_save_regs;
+	of_gc->gpio_cells = 2;
+	gc->ngpio = 8;
+	gc->direction_input = u8_gpio_dir_in;
+	gc->direction_output = u8_gpio_dir_out;
+	gc->get = u8_gpio_get;
+	gc->set = u8_gpio_set;
+
+	ret = of_mm_gpiochip_add(np, mm_gc);
+	if (ret)
+		goto err;
+	return 0;
+err:
+	kfree(u8_gc);
+	return ret;
+}
+
+int __init simple_gpiochip_init(const char *compatible)
+{
+	struct device_node *np;
+
+	for_each_compatible_node(np, NULL, compatible) {
+		int ret;
+		struct resource r;
+
+		ret = of_address_to_resource(np, 0, &r);
+		if (ret)
+			goto err;
+
+		switch (resource_size(&r)) {
+		case 1:
+			ret = u8_simple_gpiochip_add(np);
+			if (ret)
+				goto err;
+			break;
+		default:
+			/*
+			 * Whenever you need support for GPIO bank width > 1,
+			 * please just turn u8_ code into huge macros, and
+			 * construct needed uX_ code with it.
+			 */
+			ret = -ENOSYS;
+			goto err;
+		}
+		continue;
+err:
+		pr_err("%s: registration failed, status %d\n",
+		       np->full_name, ret);
+	}
+	return 0;
+}
diff --git a/arch/powerpc/sysdev/simple_gpio.h b/arch/powerpc/sysdev/simple_gpio.h
new file mode 100644
index 0000000..389f712
--- /dev/null
+++ b/arch/powerpc/sysdev/simple_gpio.h
@@ -0,0 +1,13 @@
+#ifndef __SYSDEV_SIMPLE_GPIO_H
+#define __SYSDEV_SIMPLE_GPIO_H
+
+#ifdef CONFIG_SIMPLE_GPIO
+extern int __init simple_gpiochip_init(const char *compatible);
+#else
+static inline int __init simple_gpiochip_init(const char *compatible)
+{
+	return -ENODEV;
+}
+#endif /* CONFIG_SIMPLE_GPIO */
+
+#endif /* __SYSDEV_SIMPLE_GPIO_H */
-- 
1.5.6.3

[PATCH 3/4] powerpc/83xx: add USB Host/Gadget support for the MPC8360E-MDS boards

[Anton Vorontsov]

- Update the device tree per QE USB bindings;
- Add timer (FSL GTM) node;
- Add gpio-controller node for BCSR13 bank (GPIOs on that bank
  are used to control the USB transceiver);
- Set up other BCSR registers;
- Configure the QE Par IO.

The work is loosely based on Li Yang's patch[1], which is used
to support peripheral mode only.

[1] http://ozlabs.org/pipermail/linuxppc-dev/2008-August/061357.html

The s-o-b line of the original patch preserved here.

Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
---
 arch/powerpc/boot/dts/mpc836x_mds.dts     |   43 ++++++++++++++++++++++-
 arch/powerpc/platforms/83xx/mpc836x_mds.c |   52 ++++++++++++++++++++++++++++-
 2 files changed, 92 insertions(+), 3 deletions(-)

diff --git a/arch/powerpc/boot/dts/mpc836x_mds.dts b/arch/powerpc/boot/dts/mpc836x_mds.dts
index 66a12d2..bdb14ba 100644
--- a/arch/powerpc/boot/dts/mpc836x_mds.dts
+++ b/arch/powerpc/boot/dts/mpc836x_mds.dts
@@ -69,8 +69,18 @@
 		};
 
 		bcsr@1,0 {
+			#address-cells = <1>;
+			#size-cells = <1>;
 			device_type = "board-control";
 			reg = <1 0 0x8000>;
+			ranges = <0 1 0 0x8000>;
+
+			bcsr13: gpio-controller@d {
+				#gpio-cells = <2>;
+				compatible = "fsl,mpc8360mds-bcsr-gpio";
+				reg = <0xd 1>;
+				gpio-controller;
+			};
 		};
 	};
 
@@ -195,10 +205,21 @@
 		};
 
 		par_io@1400 {
+			#address-cells = <1>;
+			#size-cells = <1>;
 			reg = <0x1400 0x100>;
+			ranges = <0 0x1400 0x100>;
 			device_type = "par_io";
 			num-ports = <7>;
 
+			qe_pio_b: gpio-controller@18 {
+				#gpio-cells = <2>;
+				compatible = "fsl,mpc8360-qe-pario-bank",
+					     "fsl,mpc8323-qe-pario-bank";
+				reg = <0x18 0x18>;
+				gpio-controller;
+			};
+
 			pio1: ucc_pin@01 {
 				pio-map = <
 			/* port  pin  dir  open_drain  assignment  has_irq */
@@ -282,6 +303,15 @@
 			};
 		};
 
+		timer@440 {
+			compatible = "fsl,mpc8360-qe-gtm",
+				     "fsl,qe-gtm", "fsl,gtm";
+			reg = <0x440 0x40>;
+			clock-frequency = <132000000>;
+			interrupts = <12 13 14 15>;
+			interrupt-parent = <&qeic>;
+		};
+
 		spi@4c0 {
 			cell-index = <0>;
 			compatible = "fsl,spi";
@@ -301,11 +331,20 @@
 		};
 
 		usb@6c0 {
-			compatible = "qe_udc";
+			compatible = "fsl,mpc8360-qe-usb",
+				     "fsl,mpc8323-qe-usb";
 			reg = <0x6c0 0x40 0x8b00 0x100>;
 			interrupts = <11>;
 			interrupt-parent = <&qeic>;
-			mode = "slave";
+			fsl,fullspeed-clock = "clk21";
+			fsl,lowspeed-clock = "brg9";
+			gpios = <&qe_pio_b  2 0   /* USBOE */
+				 &qe_pio_b  3 0   /* USBTP */
+				 &qe_pio_b  8 0   /* USBTN */
+				 &qe_pio_b  9 0   /* USBRP */
+				 &qe_pio_b 11 0   /* USBRN */
+				 &bcsr13    5 0   /* SPEED */
+				 &bcsr13    4 1>; /* POWER */
 		};
 
 		enet0: ucc@2000 {
diff --git a/arch/powerpc/platforms/83xx/mpc836x_mds.c b/arch/powerpc/platforms/83xx/mpc836x_mds.c
index 9d46e5b..4e69f7b 100644
--- a/arch/powerpc/platforms/83xx/mpc836x_mds.c
+++ b/arch/powerpc/platforms/83xx/mpc836x_mds.c
@@ -43,6 +43,7 @@
 #include <asm/udbg.h>
 #include <sysdev/fsl_soc.h>
 #include <sysdev/fsl_pci.h>
+#include <sysdev/simple_gpio.h>
 #include <asm/qe.h>
 #include <asm/qe_ic.h>
 
@@ -127,9 +128,58 @@ static void __init mpc836x_mds_setup_arch(void)
 			iounmap(immap);
 		}
 
-		iounmap(bcsr_regs);
 		of_node_put(np);
 	}
+#ifdef CONFIG_QE_USB
+	np = of_find_compatible_node(NULL, NULL, "fsl,mpc8323-qe-usb");
+	if (np) {
+		const char *mode = of_get_property(np, "mode", NULL);
+
+		par_io_config_pin(1,  2, 1, 0, 3, 0); /* USBOE  */
+		par_io_config_pin(1,  3, 1, 0, 3, 0); /* USBTP  */
+		par_io_config_pin(1,  8, 1, 0, 1, 0); /* USBTN  */
+		par_io_config_pin(1, 10, 2, 0, 3, 0); /* USBRXD */
+		par_io_config_pin(1,  9, 2, 1, 3, 0); /* USBRP  */
+		par_io_config_pin(1, 11, 2, 1, 3, 0); /* USBRN  */
+		par_io_config_pin(2, 20, 2, 0, 1, 0); /* CLK21  */
+
+#define BCSR8_TSEC1M_MASK	(0x3 << 6)
+#define BCSR8_TSEC1M_RGMII	(0x0 << 6)
+#define BCSR8_TSEC2M_MASK	(0x3 << 4)
+#define BCSR8_TSEC2M_RGMII	(0x0 << 4)
+		/*
+		 * Default is GMII (2), but we should set it to RGMII (0) if
+		 * we use USB (Eth PHY is in RGMII mode anyway).
+		 */
+		clrsetbits_8(&bcsr_regs[8],
+			     BCSR8_TSEC1M_MASK | BCSR8_TSEC2M_MASK,
+			     BCSR8_TSEC1M_RGMII | BCSR8_TSEC2M_RGMII);
+
+#define BCSR13_USBMASK	0x0f
+#define BCSR13_nUSBEN	0x08 /* 1 - Disable, 0 - Enable			*/
+#define BCSR13_USBSPEED 0x04 /* 1 - Full, 0 - Low			*/
+#define BCSR13_USBMODE	0x02 /* 1 - Host, 0 - Function			*/
+#define BCSR13_nUSBVCC	0x01 /* 1 - gets VBUS, 0 - supplies VBUS 	*/
+
+		clrsetbits_8(&bcsr_regs[13], BCSR13_USBMASK, BCSR13_USBSPEED);
+
+		if (mode && !strcmp(mode, "peripheral")) {
+			setbits8(&bcsr_regs[13], BCSR13_nUSBVCC);
+			qe_usb_clock_set(QE_CLK21, 48000000);
+		} else {
+			setbits8(&bcsr_regs[13], BCSR13_USBMODE);
+			/*
+			 * The BCSR GPIOs are used to control power and
+			 * speed of the USB transceiver. This is needed for
+			 * the USB Host only.
+			 */
+			simple_gpiochip_init("fsl,mpc8360mds-bcsr-gpio");
+		}
+
+		of_node_put(np);
+	}
+#endif				/* CONFIG_QE_USB */
+	iounmap(bcsr_regs);
 #endif				/* CONFIG_QUICC_ENGINE */
 }
 
-- 
1.5.6.3

[PATCH 4/4] powerpc/83xx: add USB Host support for the MPC8360E-RDK boards

[Anton Vorontsov]

Simply add the usb node to support USB host on the MPC8360E-RDK
boards.

Currently U-Boot doesn't fill the clock-frequency property for
timer nodes, so for now we have to fill it manually.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
---
 arch/powerpc/boot/dts/mpc836x_rdk.dts |   19 +++++++++++++++++--
 1 files changed, 17 insertions(+), 2 deletions(-)

diff --git a/arch/powerpc/boot/dts/mpc836x_rdk.dts b/arch/powerpc/boot/dts/mpc836x_rdk.dts
index decadf3..37b7895 100644
--- a/arch/powerpc/boot/dts/mpc836x_rdk.dts
+++ b/arch/powerpc/boot/dts/mpc836x_rdk.dts
@@ -218,8 +218,23 @@
 				reg = <0x440 0x40>;
 				interrupts = <12 13 14 15>;
 				interrupt-parent = <&qeic>;
-				/* filled by u-boot */
-				clock-frequency = <0>;
+				clock-frequency = <166666666>;
+			};
+
+			usb@6c0 {
+				compatible = "fsl,mpc8360-qe-usb",
+					     "fsl,mpc8323-qe-usb";
+				reg = <0x6c0 0x40 0x8b00 0x100>;
+				interrupts = <11>;
+				interrupt-parent = <&qeic>;
+				fsl,fullspeed-clock = "clk21";
+				gpios = <&qe_pio_b  2 0 /* USBOE */
+					 &qe_pio_b  3 0 /* USBTP */
+					 &qe_pio_b  8 0 /* USBTN */
+					 &qe_pio_b  9 0 /* USBRP */
+					 &qe_pio_b 11 0 /* USBRN */
+					 &qe_pio_e 20 0 /* SPEED */
+					 &qe_pio_e 21 1 /* POWER */>;
 			};
 
 			spi@4c0 {
-- 
1.5.6.3