From: Tony Lindgren <tony@atomide.com>
To: linux-arm-kernel@lists.arm.linux.org.uk
Cc: David Brownell <dbrownell@users.sourceforge.net>,
linux-omap@vger.kernel.org
Subject: [PATCH 05/11] ARM: OMAP: switch to gpio_direction_input
Date: Fri, 28 Nov 2008 17:10:22 -0800 [thread overview]
Message-ID: <20081129011021.12337.25141.stgit@localhost> (raw)
In-Reply-To: <20081129010728.12337.8217.stgit@localhost>
From: David Brownell <dbrownell@users.sourceforge.net>
More switchover to the cross-platform GPIO interface:
use gpio_direction_input(), not an OMAP-specific call.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
arch/arm/mach-omap1/board-palmte.c | 4 ++--
arch/arm/mach-omap1/board-palmz71.c | 4 ++--
arch/arm/mach-omap1/board-voiceblue.c | 2 +-
arch/arm/mach-omap1/fpga.c | 2 +-
arch/arm/mach-omap1/serial.c | 2 +-
arch/arm/mach-omap2/board-2430sdp.c | 2 +-
arch/arm/mach-omap2/board-apollon.c | 8 ++++----
arch/arm/mach-omap2/usb-tusb6010.c | 2 +-
arch/arm/plat-omap/debug-devices.c | 2 +-
drivers/mtd/onenand/omap2.c | 2 +-
drivers/usb/host/ohci-omap.c | 2 +-
11 files changed, 16 insertions(+), 16 deletions(-)
diff --git a/arch/arm/mach-omap1/board-palmte.c b/arch/arm/mach-omap1/board-palmte.c
index df663ba..0995a0f 100644
--- a/arch/arm/mach-omap1/board-palmte.c
+++ b/arch/arm/mach-omap1/board-palmte.c
@@ -351,14 +351,14 @@ static void __init palmte_misc_gpio_setup(void)
printk(KERN_ERR "Could not reserve PINTDAV GPIO!\n");
return;
}
- omap_set_gpio_direction(PALMTE_PINTDAV_GPIO, 1);
+ gpio_direction_input(PALMTE_PINTDAV_GPIO);
/* Set USB-or-DC-IN pin as input (unused) */
if (omap_request_gpio(PALMTE_USB_OR_DC_GPIO)) {
printk(KERN_ERR "Could not reserve cable signal GPIO!\n");
return;
}
- omap_set_gpio_direction(PALMTE_USB_OR_DC_GPIO, 1);
+ gpio_direction_input(PALMTE_USB_OR_DC_GPIO);
}
static void __init omap_palmte_init(void)
diff --git a/arch/arm/mach-omap1/board-palmz71.c b/arch/arm/mach-omap1/board-palmz71.c
index c33766c..5a232ad 100644
--- a/arch/arm/mach-omap1/board-palmz71.c
+++ b/arch/arm/mach-omap1/board-palmz71.c
@@ -331,7 +331,7 @@ palmz71_gpio_setup(int early)
printk(KERN_ERR "Could not reserve WP GPIO!\n");
return;
}
- omap_set_gpio_direction(PALMZ71_MMC_WP_GPIO, 1);
+ gpio_direction_input(PALMZ71_MMC_WP_GPIO);
/* Monitor the Power-cable-connected signal */
if (omap_request_gpio(PALMZ71_USBDETECT_GPIO)) {
@@ -339,7 +339,7 @@ palmz71_gpio_setup(int early)
"Could not reserve cable signal GPIO!\n");
return;
}
- omap_set_gpio_direction(PALMZ71_USBDETECT_GPIO, 1);
+ gpio_direction_input(PALMZ71_USBDETECT_GPIO);
if (request_irq(OMAP_GPIO_IRQ(PALMZ71_USBDETECT_GPIO),
palmz71_powercable, IRQF_SAMPLE_RANDOM,
"palmz71-cable", 0))
diff --git a/arch/arm/mach-omap1/board-voiceblue.c b/arch/arm/mach-omap1/board-voiceblue.c
index d7ab11a..86e73b7 100644
--- a/arch/arm/mach-omap1/board-voiceblue.c
+++ b/arch/arm/mach-omap1/board-voiceblue.c
@@ -256,7 +256,7 @@ void voiceblue_wdt_disable(void)
gpio_set_value(0, 0);
gpio_set_value(0, 1);
gpio_set_value(0, 0);
- omap_set_gpio_direction(0, 1);
+ gpio_direction_input(0);
}
void voiceblue_wdt_ping(void)
diff --git a/arch/arm/mach-omap1/fpga.c b/arch/arm/mach-omap1/fpga.c
index 0499538..40cf504 100644
--- a/arch/arm/mach-omap1/fpga.c
+++ b/arch/arm/mach-omap1/fpga.c
@@ -178,7 +178,7 @@ void omap1510_fpga_init_irq(void)
* gpio.[ch]
*/
omap_request_gpio(13);
- omap_set_gpio_direction(13, 1);
+ gpio_direction_input(13);
set_irq_type(OMAP_GPIO_IRQ(13), IRQ_TYPE_EDGE_RISING);
set_irq_chained_handler(OMAP1510_INT_FPGA, innovator_fpga_IRQ_demux);
}
diff --git a/arch/arm/mach-omap1/serial.c b/arch/arm/mach-omap1/serial.c
index 528691d..1a0bc47 100644
--- a/arch/arm/mach-omap1/serial.c
+++ b/arch/arm/mach-omap1/serial.c
@@ -250,7 +250,7 @@ static void __init omap_serial_set_port_wakeup(int gpio_nr)
gpio_nr);
return;
}
- omap_set_gpio_direction(gpio_nr, 1);
+ gpio_direction_input(gpio_nr);
ret = request_irq(OMAP_GPIO_IRQ(gpio_nr), &omap_serial_wake_interrupt,
IRQF_TRIGGER_RISING, "serial wakeup", NULL);
if (ret) {
diff --git a/arch/arm/mach-omap2/board-2430sdp.c b/arch/arm/mach-omap2/board-2430sdp.c
index 24688ef..f844a67 100644
--- a/arch/arm/mach-omap2/board-2430sdp.c
+++ b/arch/arm/mach-omap2/board-2430sdp.c
@@ -174,7 +174,7 @@ static inline void __init sdp2430_init_smc91x(void)
gpmc_cs_free(eth_cs);
goto out;
}
- omap_set_gpio_direction(OMAP24XX_ETHR_GPIO_IRQ, 1);
+ gpio_direction_input(OMAP24XX_ETHR_GPIO_IRQ);
out:
clk_disable(gpmc_fck);
diff --git a/arch/arm/mach-omap2/board-apollon.c b/arch/arm/mach-omap2/board-apollon.c
index a4ba52c..abc9167 100644
--- a/arch/arm/mach-omap2/board-apollon.c
+++ b/arch/arm/mach-omap2/board-apollon.c
@@ -242,7 +242,7 @@ static inline void __init apollon_init_smc91x(void)
gpmc_cs_free(APOLLON_ETH_CS);
goto out;
}
- omap_set_gpio_direction(APOLLON_ETHR_GPIO_IRQ, 1);
+ gpio_direction_input(APOLLON_ETHR_GPIO_IRQ);
out:
clk_disable(gpmc_fck);
@@ -327,15 +327,15 @@ static void __init apollon_sw_init(void)
/* Enter SW - Y11 */
omap_cfg_reg(Y11_242X_GPIO16);
omap_request_gpio(SW_ENTER_GPIO16);
- omap_set_gpio_direction(SW_ENTER_GPIO16, 1);
+ gpio_direction_input(SW_ENTER_GPIO16);
/* Up SW - AA12 */
omap_cfg_reg(AA12_242X_GPIO17);
omap_request_gpio(SW_UP_GPIO17);
- omap_set_gpio_direction(SW_UP_GPIO17, 1);
+ gpio_direction_input(SW_UP_GPIO17);
/* Down SW - AA8 */
omap_cfg_reg(AA8_242X_GPIO58);
omap_request_gpio(SW_DOWN_GPIO58);
- omap_set_gpio_direction(SW_DOWN_GPIO58, 1);
+ gpio_direction_input(SW_DOWN_GPIO58);
set_irq_type(OMAP_GPIO_IRQ(SW_ENTER_GPIO16), IRQ_TYPE_EDGE_RISING);
if (request_irq(OMAP_GPIO_IRQ(SW_ENTER_GPIO16), &apollon_sw_interrupt,
diff --git a/arch/arm/mach-omap2/usb-tusb6010.c b/arch/arm/mach-omap2/usb-tusb6010.c
index 10ef464..eb2399d 100644
--- a/arch/arm/mach-omap2/usb-tusb6010.c
+++ b/arch/arm/mach-omap2/usb-tusb6010.c
@@ -297,7 +297,7 @@ tusb6010_setup_interface(struct musb_hdrc_platform_data *data,
printk(error, 3, status);
return status;
}
- omap_set_gpio_direction(irq, 1);
+ gpio_direction_input(irq);
tusb_resources[2].start = irq + IH_GPIO_BASE;
/* set up memory timings ... can speed them up later */
diff --git a/arch/arm/plat-omap/debug-devices.c b/arch/arm/plat-omap/debug-devices.c
index e31154b..60076a8 100644
--- a/arch/arm/plat-omap/debug-devices.c
+++ b/arch/arm/plat-omap/debug-devices.c
@@ -77,7 +77,7 @@ int __init debug_card_init(u32 addr, unsigned gpio)
printk(KERN_ERR "GPIO%d unavailable for smc91x IRQ\n", gpio);
return status;
}
- omap_set_gpio_direction(gpio, 1);
+ gpio_direction_input(gpio);
led_resources[0].start = addr;
led_resources[0].end = addr + SZ_4K - 1;
diff --git a/drivers/mtd/onenand/omap2.c b/drivers/mtd/onenand/omap2.c
index 8dda06c..c7145af 100644
--- a/drivers/mtd/onenand/omap2.c
+++ b/drivers/mtd/onenand/omap2.c
@@ -635,7 +635,7 @@ static int __devinit omap2_onenand_probe(struct platform_device *pdev)
"OneNAND\n", c->gpio_irq);
goto err_iounmap;
}
- omap_set_gpio_direction(c->gpio_irq, 1);
+ gpio_direction_input(c->gpio_irq);
if ((r = request_irq(OMAP_GPIO_IRQ(c->gpio_irq),
omap2_onenand_interrupt, IRQF_TRIGGER_RISING,
diff --git a/drivers/usb/host/ohci-omap.c b/drivers/usb/host/ohci-omap.c
index 91697bd..22f6d19 100644
--- a/drivers/usb/host/ohci-omap.c
+++ b/drivers/usb/host/ohci-omap.c
@@ -255,7 +255,7 @@ static int ohci_omap_init(struct usb_hcd *hcd)
/* gpio9 for overcurrent detction */
omap_cfg_reg(W8_1610_GPIO9);
omap_request_gpio(9);
- omap_set_gpio_direction(9, 1 /* IN */);
+ gpio_direction_input(9);
/* for paranoia's sake: disable USB.PUEN */
omap_cfg_reg(W4_USB_HIGHZ);
next prev parent reply other threads:[~2008-11-29 1:10 UTC|newest]
Thread overview: 14+ messages / expand[flat|nested] mbox.gz Atom feed top
2008-11-29 1:09 [PATCH 00/11] Omap gpio updates for review for 2.6.29 merge window Tony Lindgren
2008-11-29 1:09 ` [PATCH 01/11] ARM: OMAP: Enable GPIO debounce clock only when debounce is enabled v3 Tony Lindgren
2008-11-29 1:09 ` [PATCH 02/11] ARM: OMAP: Extend gpio label column width in omap_gpio debugfs file Tony Lindgren
2008-11-29 1:10 ` [PATCH 03/11] ARM: OMAP: gpios implement new to_irq() Tony Lindgren
2008-11-29 1:10 ` [PATCH 04/11] ARM: OMAP: switch to standard gpio get/set calls Tony Lindgren
2008-11-29 1:10 ` Tony Lindgren [this message]
2008-11-29 1:10 ` [PATCH 06/11] ARM: OMAP: switch to gpio_direction_output Tony Lindgren
2008-11-29 1:10 ` [PATCH 07/11] ARM: OMAP: use gpio_to_irq Tony Lindgren
2008-11-29 1:10 ` [PATCH 08/11] ARM: OMAP: make legacy gpio request/free calls superfluous Tony Lindgren
2008-11-29 1:10 ` [PATCH 09/11] ARM: OMAP: minor gpio bugfixes Tony Lindgren
2008-11-29 1:10 ` [PATCH 10/11] ARM: OMAP: Switch to gpio_request/free calls Tony Lindgren
2008-12-09 1:29 ` [PATCH 10/11] ARM: OMAP: Switch to gpio_request/free calls, v2 Tony Lindgren
2008-11-29 1:11 ` [PATCH 11/11] ARM: OMAP: Switch ohci-omap to gpio_request/free calls Tony Lindgren
2008-11-29 1:35 ` David Brownell
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20081129011021.12337.25141.stgit@localhost \
--to=tony@atomide.com \
--cc=dbrownell@users.sourceforge.net \
--cc=linux-arm-kernel@lists.arm.linux.org.uk \
--cc=linux-omap@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.