From: Anton Vorontsov <avorontsov@ru.mvista.com>
To: Pierre Ossman <drzeus-sdhci@drzeus.cx>
Cc: Ben Dooks <ben-linux@fluff.org>, Arnd Bergmann <arnd@arndb.de>,
Liu Dave <DaveLiu@freescale.com>,
linux-kernel@vger.kernel.org, linuxppc-dev@ozlabs.org,
sdhci-devel@list.drzeus.cx
Subject: [PATCH 04/11] sdhci: Add support for card-detection polling
Date: Fri, 6 Feb 2009 21:06:50 +0300 [thread overview]
Message-ID: <20090206180650.GD11548@oksana.dev.rtsoft.ru> (raw)
In-Reply-To: <20090206180520.GA16123@oksana.dev.rtsoft.ru>
This patch adds SDHCI_QUIRK_BROKEN_CARD_DETECTION quirk. When specified,
sdhci driver will set MMC_CAP_NEEDS_POLL MMC host capability, and won't
enable card insert/remove interrupts.
This is needed for hosts with unreliable card detection, such as FSL
eSDHC. The original eSDHC driver was tring to "debounce" card-detection
IRQs by reading present state and disabling particular interrupts. But
with this debouncing scheme I noticed that sometimes we miss card
insertion/removal events.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
---
drivers/mmc/host/sdhci.c | 6 ++++++
drivers/mmc/host/sdhci.h | 2 ++
2 files changed, 8 insertions(+), 0 deletions(-)
diff --git a/drivers/mmc/host/sdhci.c b/drivers/mmc/host/sdhci.c
index b7a79a0..45c5f1f 100644
--- a/drivers/mmc/host/sdhci.c
+++ b/drivers/mmc/host/sdhci.c
@@ -162,6 +162,9 @@ static void sdhci_init(struct sdhci_host *host)
SDHCI_INT_DMA_END | SDHCI_INT_DATA_END | SDHCI_INT_RESPONSE |
SDHCI_INT_ADMA_ERROR;
+ if (host->quirks & SDHCI_QUIRK_BROKEN_CARD_DETECTION)
+ intmask &= ~(SDHCI_INT_CARD_REMOVE | SDHCI_INT_CARD_INSERT);
+
sdhci_writel(host, intmask, SDHCI_INT_ENABLE);
sdhci_writel(host, intmask, SDHCI_SIGNAL_ENABLE);
}
@@ -1684,6 +1687,9 @@ int sdhci_add_host(struct sdhci_host *host)
mmc->f_max = host->max_clk;
mmc->caps = MMC_CAP_4_BIT_DATA | MMC_CAP_SDIO_IRQ;
+ if (host->quirks & SDHCI_QUIRK_BROKEN_CARD_DETECTION)
+ mmc->caps |= MMC_CAP_NEEDS_POLL;
+
if ((caps & SDHCI_CAN_DO_HISPD) ||
(host->quirks & SDHCI_QUIRK_FORCE_HIGHSPEED))
mmc->caps |= MMC_CAP_SD_HIGHSPEED;
diff --git a/drivers/mmc/host/sdhci.h b/drivers/mmc/host/sdhci.h
index 5a5c119..03f035e 100644
--- a/drivers/mmc/host/sdhci.h
+++ b/drivers/mmc/host/sdhci.h
@@ -227,6 +227,8 @@ struct sdhci_host {
#define SDHCI_QUIRK_FORCE_HIGHSPEED (1<<14)
/* Controller does not provide transfer-complete interrupt when not busy */
#define SDHCI_QUIRK_NO_BUSY_IRQ (1<<15)
+/* Controller has unreliable card detection */
+#define SDHCI_QUIRK_BROKEN_CARD_DETECTION (1<<16)
int irq; /* Device IRQ */
void __iomem * ioaddr; /* Mapped address */
--
1.5.6.5
WARNING: multiple messages have this Message-ID (diff)
From: Anton Vorontsov <avorontsov@ru.mvista.com>
To: Pierre Ossman <drzeus-sdhci@drzeus.cx>
Cc: Ben Dooks <ben-linux@fluff.org>, Arnd Bergmann <arnd@arndb.de>,
Kumar Gala <galak@kernel.crashing.org>,
Liu Dave <DaveLiu@freescale.com>,
sdhci-devel@list.drzeus.cx, linux-kernel@vger.kernel.org,
linuxppc-dev@ozlabs.org
Subject: [PATCH 04/11] sdhci: Add support for card-detection polling
Date: Fri, 6 Feb 2009 21:06:50 +0300 [thread overview]
Message-ID: <20090206180650.GD11548@oksana.dev.rtsoft.ru> (raw)
In-Reply-To: <20090206180520.GA16123@oksana.dev.rtsoft.ru>
This patch adds SDHCI_QUIRK_BROKEN_CARD_DETECTION quirk. When specified,
sdhci driver will set MMC_CAP_NEEDS_POLL MMC host capability, and won't
enable card insert/remove interrupts.
This is needed for hosts with unreliable card detection, such as FSL
eSDHC. The original eSDHC driver was tring to "debounce" card-detection
IRQs by reading present state and disabling particular interrupts. But
with this debouncing scheme I noticed that sometimes we miss card
insertion/removal events.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
---
drivers/mmc/host/sdhci.c | 6 ++++++
drivers/mmc/host/sdhci.h | 2 ++
2 files changed, 8 insertions(+), 0 deletions(-)
diff --git a/drivers/mmc/host/sdhci.c b/drivers/mmc/host/sdhci.c
index b7a79a0..45c5f1f 100644
--- a/drivers/mmc/host/sdhci.c
+++ b/drivers/mmc/host/sdhci.c
@@ -162,6 +162,9 @@ static void sdhci_init(struct sdhci_host *host)
SDHCI_INT_DMA_END | SDHCI_INT_DATA_END | SDHCI_INT_RESPONSE |
SDHCI_INT_ADMA_ERROR;
+ if (host->quirks & SDHCI_QUIRK_BROKEN_CARD_DETECTION)
+ intmask &= ~(SDHCI_INT_CARD_REMOVE | SDHCI_INT_CARD_INSERT);
+
sdhci_writel(host, intmask, SDHCI_INT_ENABLE);
sdhci_writel(host, intmask, SDHCI_SIGNAL_ENABLE);
}
@@ -1684,6 +1687,9 @@ int sdhci_add_host(struct sdhci_host *host)
mmc->f_max = host->max_clk;
mmc->caps = MMC_CAP_4_BIT_DATA | MMC_CAP_SDIO_IRQ;
+ if (host->quirks & SDHCI_QUIRK_BROKEN_CARD_DETECTION)
+ mmc->caps |= MMC_CAP_NEEDS_POLL;
+
if ((caps & SDHCI_CAN_DO_HISPD) ||
(host->quirks & SDHCI_QUIRK_FORCE_HIGHSPEED))
mmc->caps |= MMC_CAP_SD_HIGHSPEED;
diff --git a/drivers/mmc/host/sdhci.h b/drivers/mmc/host/sdhci.h
index 5a5c119..03f035e 100644
--- a/drivers/mmc/host/sdhci.h
+++ b/drivers/mmc/host/sdhci.h
@@ -227,6 +227,8 @@ struct sdhci_host {
#define SDHCI_QUIRK_FORCE_HIGHSPEED (1<<14)
/* Controller does not provide transfer-complete interrupt when not busy */
#define SDHCI_QUIRK_NO_BUSY_IRQ (1<<15)
+/* Controller has unreliable card detection */
+#define SDHCI_QUIRK_BROKEN_CARD_DETECTION (1<<16)
int irq; /* Device IRQ */
void __iomem * ioaddr; /* Mapped address */
--
1.5.6.5
next prev parent reply other threads:[~2009-02-06 18:06 UTC|newest]
Thread overview: 54+ messages / expand[flat|nested] mbox.gz Atom feed top
2009-02-06 18:05 [PATCH RFC 0/11] FSL eSDHC support: second call for comments Anton Vorontsov
2009-02-06 18:05 ` Anton Vorontsov
2009-02-06 18:06 ` [PATCH 01/11] sdhci: Add quirk for controllers with no end-of-busy IRQ Anton Vorontsov
2009-02-06 18:06 ` Anton Vorontsov
2009-02-06 18:06 ` [PATCH 02/11] sdhci: Add support for bus-specific IO memory accessors Anton Vorontsov
2009-02-06 18:06 ` Anton Vorontsov
2009-02-08 20:50 ` Pierre Ossman
2009-02-08 20:50 ` Pierre Ossman
2009-02-13 14:40 ` Anton Vorontsov
2009-02-13 14:40 ` Anton Vorontsov
2009-02-21 15:57 ` Pierre Ossman
2009-02-21 15:57 ` Pierre Ossman
2009-03-04 17:46 ` Anton Vorontsov
2009-03-04 17:46 ` Anton Vorontsov
2009-03-08 14:08 ` Pierre Ossman
2009-03-08 14:08 ` Pierre Ossman
2009-02-06 18:06 ` [PATCH 03/11] sdhci: Add type checking for " Anton Vorontsov
2009-02-06 18:06 ` Anton Vorontsov
2009-02-08 20:53 ` Pierre Ossman
2009-02-08 20:53 ` Pierre Ossman
2009-02-06 18:06 ` Anton Vorontsov [this message]
2009-02-06 18:06 ` [PATCH 04/11] sdhci: Add support for card-detection polling Anton Vorontsov
2009-02-08 20:57 ` Pierre Ossman
2009-02-08 20:57 ` Pierre Ossman
2009-02-06 18:06 ` [PATCH 05/11] sdhci: Add support for hosts reporting inverted write-protect state Anton Vorontsov
2009-02-06 18:06 ` Anton Vorontsov
2009-02-06 18:06 ` [PATCH 06/11] sdhci: Add support for hosts with strict 32 bit addressing Anton Vorontsov
2009-02-06 18:06 ` Anton Vorontsov
2009-02-06 18:06 ` [PATCH 07/11] sdhci: Add quirk to suppress PIO interrupts during DMA transfers Anton Vorontsov
2009-02-06 18:06 ` Anton Vorontsov
2009-02-08 21:02 ` Pierre Ossman
2009-02-08 21:02 ` Pierre Ossman
2009-02-06 18:06 ` [PATCH 08/11] sdhci: Add support for hosts that don't specify clocks in the cap. register Anton Vorontsov
2009-02-06 18:06 ` Anton Vorontsov
2009-02-08 21:04 ` Pierre Ossman
2009-02-08 21:04 ` Pierre Ossman
2009-02-06 18:06 ` [PATCH 09/11] sdhci: Add set_clock callback Anton Vorontsov
2009-02-06 18:06 ` Anton Vorontsov
2009-02-08 21:06 ` Pierre Ossman
2009-02-08 21:06 ` Pierre Ossman
2009-02-06 18:07 ` [PATCH 10/11] sdhci: Add quirk for Freescale eSDHC controllers Anton Vorontsov
2009-02-06 18:07 ` Anton Vorontsov
2009-02-08 21:12 ` Pierre Ossman
2009-02-08 21:12 ` Pierre Ossman
2009-02-13 14:42 ` Anton Vorontsov
2009-02-13 14:42 ` Anton Vorontsov
2009-02-06 18:07 ` [PATCH 11/11] mmc: Add OpenFirmware bindings for SDHCI driver Anton Vorontsov
2009-02-06 18:07 ` Anton Vorontsov
2009-02-08 20:33 ` [PATCH RFC 0/11] FSL eSDHC support: second call for comments Pierre Ossman
2009-02-08 20:33 ` Pierre Ossman
-- strict thread matches above, loose matches on Subject: below --
2009-03-05 20:27 [PATCH v2 0/11] FSL eSDHC support Anton Vorontsov
2009-03-05 20:28 ` [PATCH 04/11] sdhci: Add support for card-detection polling Anton Vorontsov
2009-03-05 20:28 ` Anton Vorontsov
2009-03-16 21:13 [PATCH v3 0/11] FSL eSDHC support Anton Vorontsov
2009-03-16 21:13 ` [PATCH 04/11] sdhci: Add support for card-detection polling Anton Vorontsov
2009-03-16 21:13 ` Anton Vorontsov
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20090206180650.GD11548@oksana.dev.rtsoft.ru \
--to=avorontsov@ru.mvista.com \
--cc=DaveLiu@freescale.com \
--cc=arnd@arndb.de \
--cc=ben-linux@fluff.org \
--cc=drzeus-sdhci@drzeus.cx \
--cc=linux-kernel@vger.kernel.org \
--cc=linuxppc-dev@ozlabs.org \
--cc=sdhci-devel@list.drzeus.cx \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.