* [ath9k-devel] iw only shows 54mbps for ath9k
@ 2009-02-04 0:41 Amit Sood
2009-02-04 0:55 ` Luis R. Rodriguez
0 siblings, 1 reply; 4+ messages in thread
From: Amit Sood @ 2009-02-04 0:41 UTC (permalink / raw)
To: ath9k-devel
hi,
I'm using AR5416 (WMP300N v2) chipset with latest compat-wireless ath9k driver. when I do iw list, it only shows the card speed till 54mb. Do i need something to enable the for n capabilities?
here is the output of iw:
++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
Wiphy phy2
Band 1:
HT capabilities: 0x104e
* 20/40 MHz operation
* SM PS disabled
* 40 MHz short GI
* max A-MSDU len 3839
* DSSS/CCK 40 MHz
HT A-MPDU factor: 0x0003 (65535 bytes)
HT A-MPDU density: 0x0006 (8 usec)
HT MCS set: ff ff 00 00 00 00 00 00 00 00 00 00 01 00 00 00
Frequencies:
* 2412 MHz [1] (20.0 dBm)
* 2417 MHz [2] (20.0 dBm)
* 2422 MHz [3] (20.0 dBm)
* 2427 MHz [4] (20.0 dBm)
* 2432 MHz [5] (20.0 dBm)
* 2437 MHz [6] (20.0 dBm)
* 2442 MHz [7] (20.0 dBm)
* 2447 MHz [8] (20.0 dBm)
* 2452 MHz [9] (20.0 dBm)
* 2457 MHz [10] (20.0 dBm)
* 2462 MHz [11] (20.0 dBm)
* 2467 MHz [12] (disabled)
* 2472 MHz [13] (disabled)
* 2484 MHz [14] (disabled)
Bitrates:
* 1.0 Mbps
* 2.0 Mbps (short preamble supported)
* 5.5 Mbps (short preamble supported)
* 11.0 Mbps (short preamble supported)
* 6.0 Mbps
* 9.0 Mbps
* 12.0 Mbps
* 18.0 Mbps
* 24.0 Mbps
* 36.0 Mbps
* 48.0 Mbps
* 54.0 Mbps
Supported interface modes:
* IBSS
* Station
* AP
* AP(VLAN)
* Monitor
Wiphy phy0
Band 1:
Frequencies:
* 2412 MHz [1] (18.0 dBm)
* 2417 MHz [2] (18.0 dBm)
* 2422 MHz [3] (18.0 dBm)
* 2427 MHz [4] (18.0 dBm)
* 2432 MHz [5] (18.0 dBm)
* 2437 MHz [6] (18.0 dBm)
* 2442 MHz [7] (18.0 dBm)
* 2447 MHz [8] (18.0 dBm)
* 2452 MHz [9] (18.0 dBm)
* 2457 MHz [10] (18.0 dBm)
* 2462 MHz [11] (18.0 dBm)
* 2467 MHz [12] (18.0 dBm)
* 2472 MHz [13] (18.0 dBm)
* 2484 MHz [14] (disabled)
Bitrates:
* 1.0 Mbps
* 2.0 Mbps (short preamble supported)
* 5.5 Mbps (short preamble supported)
* 11.0 Mbps (short preamble supported)
* 6.0 Mbps
* 9.0 Mbps
* 12.0 Mbps
* 18.0 Mbps
* 24.0 Mbps
* 36.0 Mbps
* 48.0 Mbps
* 54.0 Mbps
Supported interface modes:
* IBSS
* Station
* AP
* AP(VLAN)
* WDS
* Monitor
* mesh point
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
regards,
-amit-
Add more friends to your messenger and enjoy! Go to http://messenger.yahoo.com/invite/
^ permalink raw reply [flat|nested] 4+ messages in thread* [ath9k-devel] iw only shows 54mbps for ath9k
2009-02-04 0:41 [ath9k-devel] iw only shows 54mbps for ath9k Amit Sood
@ 2009-02-04 0:55 ` Luis R. Rodriguez
2009-03-05 11:14 ` Mark Ryden
0 siblings, 1 reply; 4+ messages in thread
From: Luis R. Rodriguez @ 2009-02-04 0:55 UTC (permalink / raw)
To: ath9k-devel
On Tue, Feb 03, 2009 at 04:41:00PM -0800, Amit Sood wrote:
> hi,
>
> I'm using AR5416 (WMP300N v2) chipset with latest compat-wireless ath9k driver. when I do iw list, it only shows the card speed till 54mb. Do i need something to enable the for n capabilities?
>
> here is the output of iw:
> ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
> Wiphy phy2
> Band 1:
> HT capabilities: 0x104e
> * 20/40 MHz operation
> * SM PS disabled
> * 40 MHz short GI
> * max A-MSDU len 3839
> * DSSS/CCK 40 MHz
> HT A-MPDU factor: 0x0003 (65535 bytes)
> HT A-MPDU density: 0x0006 (8 usec)
> HT MCS set: ff ff 00 00 00 00 00 00 00 00 00 00 01 00 00 00
The supported MCS indexes are entangled above. You could use the iw patch I
posted yesterday to decipher it. It has not yet been merged. But I can also
already tell you your card supports up to MCS index 15.
Luis
^ permalink raw reply [flat|nested] 4+ messages in thread
* [ath9k-devel] iw only shows 54mbps for ath9k
2009-02-04 0:55 ` Luis R. Rodriguez
@ 2009-03-05 11:14 ` Mark Ryden
2009-03-05 19:06 ` Luis R. Rodriguez
0 siblings, 1 reply; 4+ messages in thread
From: Mark Ryden @ 2009-03-05 11:14 UTC (permalink / raw)
To: ath9k-devel
Hi,
>You could use the iw patch I
> posted yesterday to decipher it
May I ask: which mailing list was this patch sent to ?
I looked for something like iw mailing list and could not find any. I
assume you are not talking about wireless-testing mailing list.
> It has not yet been merged.
do you mean merging into the iw git tree?
rgs,
Mark
On Wed, Feb 4, 2009 at 2:55 AM, Luis R. Rodriguez
<lrodriguez@atheros.com> wrote:
> On Tue, Feb 03, 2009 at 04:41:00PM -0800, Amit Sood wrote:
>> hi,
>>
>> I'm using AR5416 (WMP300N v2) chipset with latest compat-wireless ath9k driver. when I do iw list, it only shows the card speed till 54mb. Do i need something to enable the for n capabilities?
>>
>> here is the output of iw:
>> ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
>> Wiphy phy2
>> ? ? ? ? Band 1:
>> ? ? ? ? ? ? ? ? HT capabilities: 0x104e
>> ? ? ? ? ? ? ? ? ? ? ? ? ?* 20/40 MHz operation
>> ? ? ? ? ? ? ? ? ? ? ? ? ?* SM PS disabled
>> ? ? ? ? ? ? ? ? ? ? ? ? ?* 40 MHz short GI
>> ? ? ? ? ? ? ? ? ? ? ? ? ?* max A-MSDU len 3839
>> ? ? ? ? ? ? ? ? ? ? ? ? ?* DSSS/CCK 40 MHz
>> ? ? ? ? ? ? ? ? HT A-MPDU factor: 0x0003 (65535 bytes)
>> ? ? ? ? ? ? ? ? HT A-MPDU density: 0x0006 (8 usec)
>> ? ? ? ? ? ? ? ? HT MCS set: ff ff 00 00 00 00 00 00 00 00 00 00 01 00 00 00
>
> The supported MCS indexes are entangled above. You could use the iw patch I
> posted yesterday to decipher it. It has not yet been merged. But I can also
> already tell you your card supports up to MCS index 15.
>
> ?Luis
> _______________________________________________
> ath9k-devel mailing list
> ath9k-devel at lists.ath9k.org
> https://lists.ath9k.org/mailman/listinfo/ath9k-devel
>
^ permalink raw reply [flat|nested] 4+ messages in thread
* [ath9k-devel] iw only shows 54mbps for ath9k
2009-03-05 11:14 ` Mark Ryden
@ 2009-03-05 19:06 ` Luis R. Rodriguez
0 siblings, 0 replies; 4+ messages in thread
From: Luis R. Rodriguez @ 2009-03-05 19:06 UTC (permalink / raw)
To: ath9k-devel
On Thu, Mar 05, 2009 at 03:14:15AM -0800, Mark Ryden wrote:
> Hi,
> >You could use the iw patch I
> > posted yesterday to decipher it
>
> May I ask: which mailing list was this patch sent to ?
Our Linux-wireless kernel mailing list:
http://wireless.kernel.org/en/developers/MailingLists
> I looked for something like iw mailing list and could not find any. I
> assume you are not talking about wireless-testing mailing list.
Yeah we just use linux-wireless for iw's patches as well as crda and wireless-regdb.
I'll add this to the iw wiki page when wireless.kernel.org comes back up. I think
the other userspace things do mention linux-wireless though.
> > It has not yet been merged.
> do you mean merging into the iw git tree?
Yes. Its now there so you can pull from it and get that.
Luis
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2009-03-05 19:06 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2009-02-04 0:41 [ath9k-devel] iw only shows 54mbps for ath9k Amit Sood
2009-02-04 0:55 ` Luis R. Rodriguez
2009-03-05 11:14 ` Mark Ryden
2009-03-05 19:06 ` Luis R. Rodriguez
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.