about multipath path group

about multipath path group

[杨伟]

[-- Attachment #1.1: Type: text/plain, Size: 463 bytes --]

Dear all:

Q1: In RHEL 5.2, make and make install multipath-tools-0.4.8, why does not
command "multipath -p" work well?

Q2: In RHEL 5.2, configure path group policy as failover or group_by_prio,
and then create path-prio.sh to set the priority of paths. however, the path
group with the highest priority is not always active, if I don't recreate
the multipath devices. why is that? how I make the path group with the
highest priority is active on-line?

William

[-- Attachment #1.2: Type: text/html, Size: 502 bytes --]

[-- Attachment #2: Type: text/plain, Size: 0 bytes --]

Re: about multipath path group

[Benjamin Marzinski]

On Wed, Jul 22, 2009 at 02:49:39PM +0800, 杨伟 wrote:
>    Dear all:
> 
>    Q1: In RHEL 5.2, make and make install multipath-tools-0.4.8, why does not
>    command "multipath -p" work well?

Are you using the upstream or the RHEL code.  multipath -p does work in
the RHEL code, although, if you run multipath again, or reconfigure
multipathd, it will notice that your devices aren't set up the way the
config says they should be, and it will change them back.  In general,
multipath -p is pretty worthless, you should change the configuration to
use the path grouping policy you want.

> 
>    Q2: In RHEL 5.2, configure path group policy as failover or group_by_prio,
>    and then create path-prio.sh to set the priority of paths. however, the
>    path group with the highest priority is not always active, if I don't
>    recreate the multipath devices. why is that? how I make the path group
>    with the highest priority is active on-line?

By default, multipath is configured for manual failback.  This means
that multipathd won't switch from the current active pathgroup to a
higher priority one, unless you manually force it to do so. The
easiest way to do this is by running

# service multipathd reload  or
# multipathd -k"reconfigure"

adding 

defaults {
	<other_defaults>
	failback immediate
}

to /etc/multipath.conf will make multipath immdiately switch to the
highest priority path group.

-Ben

> 
>    William

> --
> dm-devel mailing list
> dm-devel@redhat.com
> https://www.redhat.com/mailman/listinfo/dm-devel

Re: about multipath path group

[杨伟]

[-- Attachment #1.1: Type: text/plain, Size: 1901 bytes --]

Thanks very much! your comments is helpful to me


2009/8/4 Benjamin Marzinski <bmarzins@redhat.com>

> On Wed, Jul 22, 2009 at 02:49:39PM +0800, 杨伟 wrote:
> >    Dear all:
> >
> >    Q1: In RHEL 5.2, make and make install multipath-tools-0.4.8, why does
> not
> >    command "multipath -p" work well?
>
> Are you using the upstream or the RHEL code.  multipath -p does work in
> the RHEL code, although, if you run multipath again, or reconfigure
> multipathd, it will notice that your devices aren't set up the way the
> config says they should be, and it will change them back.  In general,
> multipath -p is pretty worthless, you should change the configuration to
> use the path grouping policy you want.
>
> >
> >    Q2: In RHEL 5.2, configure path group policy as failover or
> group_by_prio,
> >    and then create path-prio.sh to set the priority of paths. however,
> the
> >    path group with the highest priority is not always active, if I don't
> >    recreate the multipath devices. why is that? how I make the path group
> >    with the highest priority is active on-line?
>
> By default, multipath is configured for manual failback.  This means
> that multipathd won't switch from the current active pathgroup to a
> higher priority one, unless you manually force it to do so. The
> easiest way to do this is by running
>
> # service multipathd reload  or
> # multipathd -k"reconfigure"
>
> adding
>
> defaults {
>        <other_defaults>
>        failback immediate
> }
>
> to /etc/multipath.conf will make multipath immdiately switch to the
> highest priority path group.
>
> -Ben
>
> >
> >    William
>
> > --
> > dm-devel mailing list
> > dm-devel@redhat.com
> > https://www.redhat.com/mailman/listinfo/dm-devel
>
> --
> dm-devel mailing list
> dm-devel@redhat.com
> https://www.redhat.com/mailman/listinfo/dm-devel
>

[-- Attachment #1.2: Type: text/html, Size: 2816 bytes --]

[-- Attachment #2: Type: text/plain, Size: 0 bytes --]