All of lore.kernel.org
 help / color / mirror / Atom feed
From: Kalle Valo <kalle.valo@iki.fi>
To: linville@tuxdriver.com
Cc: linux-wireless@vger.kernel.org
Subject: [PATCH 05/23] wl1251: make wl1251_set_partition bus agnostic
Date: Fri, 07 Aug 2009 13:33:18 +0300	[thread overview]
Message-ID: <20090807103318.31717.78853.stgit@tikku> (raw)
In-Reply-To: <20090807102732.31717.84006.stgit@tikku>

From: Bob Copeland <me@bobcopeland.com>

The same partition setting code can be used for both SPI and SDIO
modes, if we remove the spi-specific commands and use the more
generic buffer write routines.  Do that and move it to io.c
since it deals with register/memory address offsets.

Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
---

 drivers/net/wireless/wl12xx/wl1251_io.c  |   95 +++++++++++++++++++++++
 drivers/net/wireless/wl12xx/wl1251_io.h  |   15 ++++
 drivers/net/wireless/wl12xx/wl1251_spi.c |  124 ------------------------------
 drivers/net/wireless/wl12xx/wl1251_spi.h |   15 ----
 4 files changed, 110 insertions(+), 139 deletions(-)

diff --git a/drivers/net/wireless/wl12xx/wl1251_io.c b/drivers/net/wireless/wl12xx/wl1251_io.c
index bc95785..db2cfbf 100644
--- a/drivers/net/wireless/wl12xx/wl1251_io.c
+++ b/drivers/net/wireless/wl12xx/wl1251_io.c
@@ -84,3 +84,98 @@ void wl1251_reg_write32(struct wl1251 *wl, int addr, u32 val)
 {
 	wl1251_write32(wl, wl1251_translate_reg_addr(wl, addr), val);
 }
+
+/* Set the partitions to access the chip addresses.
+ *
+ * There are two VIRTUAL partitions (the memory partition and the
+ * registers partition), which are mapped to two different areas of the
+ * PHYSICAL (hardware) memory.  This function also makes other checks to
+ * ensure that the partitions are not overlapping.  In the diagram below, the
+ * memory partition comes before the register partition, but the opposite is
+ * also supported.
+ *
+ *                               PHYSICAL address
+ *                                     space
+ *
+ *                                    |    |
+ *                                 ...+----+--> mem_start
+ *          VIRTUAL address     ...   |    |
+ *               space       ...      |    | [PART_0]
+ *                        ...         |    |
+ * 0x00000000 <--+----+...         ...+----+--> mem_start + mem_size
+ *               |    |         ...   |    |
+ *               |MEM |      ...      |    |
+ *               |    |   ...         |    |
+ *  part_size <--+----+...            |    | {unused area)
+ *               |    |   ...         |    |
+ *               |REG |      ...      |    |
+ *  part_size    |    |         ...   |    |
+ *      +     <--+----+...         ...+----+--> reg_start
+ *  reg_size              ...         |    |
+ *                           ...      |    | [PART_1]
+ *                              ...   |    |
+ *                                 ...+----+--> reg_start + reg_size
+ *                                    |    |
+ *
+ */
+void wl1251_set_partition(struct wl1251 *wl,
+			  u32 mem_start, u32 mem_size,
+			  u32 reg_start, u32 reg_size)
+{
+	struct wl1251_partition partition[2];
+
+	wl1251_debug(DEBUG_SPI, "mem_start %08X mem_size %08X",
+		     mem_start, mem_size);
+	wl1251_debug(DEBUG_SPI, "reg_start %08X reg_size %08X",
+		     reg_start, reg_size);
+
+	/* Make sure that the two partitions together don't exceed the
+	 * address range */
+	if ((mem_size + reg_size) > HW_ACCESS_MEMORY_MAX_RANGE) {
+		wl1251_debug(DEBUG_SPI, "Total size exceeds maximum virtual"
+			     " address range.  Truncating partition[0].");
+		mem_size = HW_ACCESS_MEMORY_MAX_RANGE - reg_size;
+		wl1251_debug(DEBUG_SPI, "mem_start %08X mem_size %08X",
+			     mem_start, mem_size);
+		wl1251_debug(DEBUG_SPI, "reg_start %08X reg_size %08X",
+			     reg_start, reg_size);
+	}
+
+	if ((mem_start < reg_start) &&
+	    ((mem_start + mem_size) > reg_start)) {
+		/* Guarantee that the memory partition doesn't overlap the
+		 * registers partition */
+		wl1251_debug(DEBUG_SPI, "End of partition[0] is "
+			     "overlapping partition[1].  Adjusted.");
+		mem_size = reg_start - mem_start;
+		wl1251_debug(DEBUG_SPI, "mem_start %08X mem_size %08X",
+			     mem_start, mem_size);
+		wl1251_debug(DEBUG_SPI, "reg_start %08X reg_size %08X",
+			     reg_start, reg_size);
+	} else if ((reg_start < mem_start) &&
+		   ((reg_start + reg_size) > mem_start)) {
+		/* Guarantee that the register partition doesn't overlap the
+		 * memory partition */
+		wl1251_debug(DEBUG_SPI, "End of partition[1] is"
+			     " overlapping partition[0].  Adjusted.");
+		reg_size = mem_start - reg_start;
+		wl1251_debug(DEBUG_SPI, "mem_start %08X mem_size %08X",
+			     mem_start, mem_size);
+		wl1251_debug(DEBUG_SPI, "reg_start %08X reg_size %08X",
+			     reg_start, reg_size);
+	}
+
+	partition[0].start = mem_start;
+	partition[0].size  = mem_size;
+	partition[1].start = reg_start;
+	partition[1].size  = reg_size;
+
+	wl->physical_mem_addr = mem_start;
+	wl->physical_reg_addr = reg_start;
+
+	wl->virtual_mem_addr = 0;
+	wl->virtual_reg_addr = mem_size;
+
+	wl->if_ops->write(wl, HW_ACCESS_PART0_SIZE_ADDR, partition,
+		sizeof(partition));
+}
diff --git a/drivers/net/wireless/wl12xx/wl1251_io.h b/drivers/net/wireless/wl12xx/wl1251_io.h
index 1fa2ab1..b89d2ac 100644
--- a/drivers/net/wireless/wl12xx/wl1251_io.h
+++ b/drivers/net/wireless/wl12xx/wl1251_io.h
@@ -23,6 +23,17 @@
 
 #include "wl1251.h"
 
+#define HW_ACCESS_MEMORY_MAX_RANGE		0x1FFC0
+
+#define HW_ACCESS_PART0_SIZE_ADDR           0x1FFC0
+#define HW_ACCESS_PART0_START_ADDR          0x1FFC4
+#define HW_ACCESS_PART1_SIZE_ADDR           0x1FFC8
+#define HW_ACCESS_PART1_START_ADDR          0x1FFCC
+
+#define HW_ACCESS_REGISTER_SIZE             4
+
+#define HW_ACCESS_PRAM_MAX_RANGE		0x3c000
+
 static inline u32 wl1251_read32(struct wl1251 *wl, int addr)
 {
 	u32 response;
@@ -46,4 +57,8 @@ void wl1251_mem_write32(struct wl1251 *wl, int addr, u32 val);
 u32 wl1251_reg_read32(struct wl1251 *wl, int addr);
 void wl1251_reg_write32(struct wl1251 *wl, int addr, u32 val);
 
+void wl1251_set_partition(struct wl1251 *wl,
+			  u32 part_start, u32 part_size,
+			  u32 reg_start,  u32 reg_size);
+
 #endif
diff --git a/drivers/net/wireless/wl12xx/wl1251_spi.c b/drivers/net/wireless/wl12xx/wl1251_spi.c
index 61a0852..ceb237b 100644
--- a/drivers/net/wireless/wl12xx/wl1251_spi.c
+++ b/drivers/net/wireless/wl12xx/wl1251_spi.c
@@ -115,130 +115,6 @@ static void wl1251_spi_reset_wake(struct wl1251 *wl)
 	wl1251_spi_init(wl);
 }
 
-
-/* Set the SPI partitions to access the chip addresses
- *
- * There are two VIRTUAL (SPI) partitions (the memory partition and the
- * registers partition), which are mapped to two different areas of the
- * PHYSICAL (hardware) memory.  This function also makes other checks to
- * ensure that the partitions are not overlapping.  In the diagram below, the
- * memory partition comes before the register partition, but the opposite is
- * also supported.
- *
- *                               PHYSICAL address
- *                                     space
- *
- *                                    |    |
- *                                 ...+----+--> mem_start
- *          VIRTUAL address     ...   |    |
- *               space       ...      |    | [PART_0]
- *                        ...         |    |
- * 0x00000000 <--+----+...         ...+----+--> mem_start + mem_size
- *               |    |         ...   |    |
- *               |MEM |      ...      |    |
- *               |    |   ...         |    |
- *  part_size <--+----+...            |    | {unused area)
- *               |    |   ...         |    |
- *               |REG |      ...      |    |
- *  part_size    |    |         ...   |    |
- *      +     <--+----+...         ...+----+--> reg_start
- *  reg_size              ...         |    |
- *                           ...      |    | [PART_1]
- *                              ...   |    |
- *                                 ...+----+--> reg_start + reg_size
- *                                    |    |
- *
- */
-int wl1251_set_partition(struct wl1251 *wl,
-			  u32 mem_start, u32 mem_size,
-			  u32 reg_start, u32 reg_size)
-{
-	struct wl1251_partition *partition;
-	struct spi_transfer t;
-	struct spi_message m;
-	size_t len, cmd_len;
-	u32 *cmd;
-	int addr;
-
-	cmd_len = sizeof(u32) + 2 * sizeof(struct wl1251_partition);
-	cmd = kzalloc(cmd_len, GFP_KERNEL);
-	if (!cmd)
-		return -ENOMEM;
-
-	spi_message_init(&m);
-	memset(&t, 0, sizeof(t));
-
-	partition = (struct wl1251_partition *) (cmd + 1);
-	addr = HW_ACCESS_PART0_SIZE_ADDR;
-	len = 2 * sizeof(struct wl1251_partition);
-
-	*cmd |= WSPI_CMD_WRITE;
-	*cmd |= (len << WSPI_CMD_BYTE_LENGTH_OFFSET) & WSPI_CMD_BYTE_LENGTH;
-	*cmd |= addr & WSPI_CMD_BYTE_ADDR;
-
-	wl1251_debug(DEBUG_SPI, "mem_start %08X mem_size %08X",
-		     mem_start, mem_size);
-	wl1251_debug(DEBUG_SPI, "reg_start %08X reg_size %08X",
-		     reg_start, reg_size);
-
-	/* Make sure that the two partitions together don't exceed the
-	 * address range */
-	if ((mem_size + reg_size) > HW_ACCESS_MEMORY_MAX_RANGE) {
-		wl1251_debug(DEBUG_SPI, "Total size exceeds maximum virtual"
-			     " address range.  Truncating partition[0].");
-		mem_size = HW_ACCESS_MEMORY_MAX_RANGE - reg_size;
-		wl1251_debug(DEBUG_SPI, "mem_start %08X mem_size %08X",
-			     mem_start, mem_size);
-		wl1251_debug(DEBUG_SPI, "reg_start %08X reg_size %08X",
-			     reg_start, reg_size);
-	}
-
-	if ((mem_start < reg_start) &&
-	    ((mem_start + mem_size) > reg_start)) {
-		/* Guarantee that the memory partition doesn't overlap the
-		 * registers partition */
-		wl1251_debug(DEBUG_SPI, "End of partition[0] is "
-			     "overlapping partition[1].  Adjusted.");
-		mem_size = reg_start - mem_start;
-		wl1251_debug(DEBUG_SPI, "mem_start %08X mem_size %08X",
-			     mem_start, mem_size);
-		wl1251_debug(DEBUG_SPI, "reg_start %08X reg_size %08X",
-			     reg_start, reg_size);
-	} else if ((reg_start < mem_start) &&
-		   ((reg_start + reg_size) > mem_start)) {
-		/* Guarantee that the register partition doesn't overlap the
-		 * memory partition */
-		wl1251_debug(DEBUG_SPI, "End of partition[1] is"
-			     " overlapping partition[0].  Adjusted.");
-		reg_size = mem_start - reg_start;
-		wl1251_debug(DEBUG_SPI, "mem_start %08X mem_size %08X",
-			     mem_start, mem_size);
-		wl1251_debug(DEBUG_SPI, "reg_start %08X reg_size %08X",
-			     reg_start, reg_size);
-	}
-
-	partition[0].start = mem_start;
-	partition[0].size  = mem_size;
-	partition[1].start = reg_start;
-	partition[1].size  = reg_size;
-
-	wl->physical_mem_addr = mem_start;
-	wl->physical_reg_addr = reg_start;
-
-	wl->virtual_mem_addr = 0;
-	wl->virtual_reg_addr = mem_size;
-
-	t.tx_buf = cmd;
-	t.len = cmd_len;
-	spi_message_add_tail(&t, &m);
-
-	spi_sync(wl->spi, &m);
-
-	kfree(cmd);
-
-	return 0;
-}
-
 static void wl1251_spi_read(struct wl1251 *wl, int addr, void *buf,
 			    size_t len)
 {
diff --git a/drivers/net/wireless/wl12xx/wl1251_spi.h b/drivers/net/wireless/wl12xx/wl1251_spi.h
index 7c6da21..cb0c228 100644
--- a/drivers/net/wireless/wl12xx/wl1251_spi.h
+++ b/drivers/net/wireless/wl12xx/wl1251_spi.h
@@ -29,17 +29,6 @@
 #include "wl1251_acx.h"
 #include "reg.h"
 
-#define HW_ACCESS_MEMORY_MAX_RANGE		0x1FFC0
-
-#define HW_ACCESS_PART0_SIZE_ADDR           0x1FFC0
-#define HW_ACCESS_PART0_START_ADDR          0x1FFC4
-#define HW_ACCESS_PART1_SIZE_ADDR           0x1FFC8
-#define HW_ACCESS_PART1_START_ADDR          0x1FFCC
-
-#define HW_ACCESS_REGISTER_SIZE             4
-
-#define HW_ACCESS_PRAM_MAX_RANGE		0x3c000
-
 #define WSPI_CMD_READ                 0x40000000
 #define WSPI_CMD_WRITE                0x00000000
 #define WSPI_CMD_FIXED                0x20000000
@@ -69,8 +58,4 @@
 		((WL1251_BUSY_WORD_LEN - 4) / sizeof(u32))
 #define HW_ACCESS_WSPI_INIT_CMD_MASK  0
 
-int wl1251_set_partition(struct wl1251 *wl,
-			 u32 part_start, u32 part_size,
-			 u32 reg_start,  u32 reg_size);
-
 #endif /* __WL1251_SPI_H__ */


  parent reply	other threads:[~2009-08-07 10:33 UTC|newest]

Thread overview: 25+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2009-08-07 10:32 [PATCH 00/23] wl1251 sdio support Kalle Valo
2009-08-07 10:32 ` [PATCH 01/23] wl1251: remove fixed address support from spi commands Kalle Valo
2009-08-07 10:32 ` [PATCH 02/23] wl1251: separate bus i/o code into io.c Kalle Valo
2009-08-07 10:33 ` [PATCH 03/23] wl1251: use wiphy_dev instead of wl->spi->dev Kalle Valo
2009-08-07 10:33 ` [PATCH 04/23] wl1251: introduce wl1251_if_operations struct Kalle Valo
2009-08-07 10:33 ` Kalle Valo [this message]
2009-08-07 10:33 ` [PATCH 06/23] wl1251: move module probe methods into spi.c Kalle Valo
2009-08-07 10:33 ` [PATCH 07/23] wl1251: split spi interface into separate module Kalle Valo
2009-08-07 10:33 ` [PATCH 08/23] wl1251: add sdio support Kalle Valo
2009-08-07 10:33 ` [PATCH 09/23] wl1251: make irq handling interface specific Kalle Valo
2009-08-07 10:33 ` [PATCH 10/23] wl1251: remove wl1251_ops Kalle Valo
2009-08-07 10:34 ` [PATCH 11/23] wl1251: reorder wl1251_cmd_join() arguments Kalle Valo
2009-08-07 10:34 ` [PATCH 12/23] wl1251: use beacon interval and dtim period provided by mac80211 Kalle Valo
2009-08-07 10:34 ` [PATCH 13/23] wl1251: remove wait parameter from wl1251_cmd_join() Kalle Valo
2009-08-07 10:34 ` [PATCH 14/23] wl1251: initialise default channel to zero Kalle Valo
2009-08-07 10:34 ` [PATCH 15/23] wl1251: add channel to wl1251_cmd_join() parameters Kalle Valo
2009-08-07 10:34 ` [PATCH 16/23] wl1251: create wl1251_join() Kalle Valo
2009-08-07 10:34 ` [PATCH 17/23] wl1251: fix channel setting in wl1251_op_config() Kalle Valo
2009-08-07 10:34 ` [PATCH 18/23] wl1251: move wl1251_acx_wake_up_conditions() to wl1251_ps_set_mode() Kalle Valo
2009-08-07 10:35 ` [PATCH 19/23] wl1251: use workqueue provided by mac80211 Kalle Valo
2009-08-07 10:35 ` [PATCH 20/23] wl1251: rename reg.h to wl1251_reg.h Kalle Valo
2009-08-07 10:35 ` [PATCH 21/23] wl1251: remove Luciano as maintainer Kalle Valo
2009-08-07 10:46   ` Luciano Coelho
2009-08-07 10:35 ` [PATCH 22/23] wl1251: add hw scan completed debug message Kalle Valo
2009-08-07 10:35 ` [PATCH 23/23] wl1251: hack to disable filters for fixing association Kalle Valo

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20090807103318.31717.78853.stgit@tikku \
    --to=kalle.valo@iki.fi \
    --cc=linux-wireless@vger.kernel.org \
    --cc=linville@tuxdriver.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.