From: Anton Vorontsov <avorontsov@ru.mvista.com>
To: u-boot@lists.denx.de
Subject: [U-Boot] [PATCH 7/7] mpc85xx: Configure QE USB for MPC8569E-MDS boards
Date: Thu, 15 Oct 2009 17:47:16 +0400 [thread overview]
Message-ID: <20091015134716.GG32478@oksana.dev.rtsoft.ru> (raw)
In-Reply-To: <20091015134644.GA31541@oksana.dev.rtsoft.ru>
Setup QE pin multiplexing for USB function, configure needed BCSRs
and add some fdt fixups.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
---
board/freescale/mpc8569mds/bcsr.h | 4 +++
board/freescale/mpc8569mds/mpc8569mds.c | 32 +++++++++++++++++++++++++++++++
drivers/qe/fdt.c | 2 +
3 files changed, 38 insertions(+), 0 deletions(-)
diff --git a/board/freescale/mpc8569mds/bcsr.h b/board/freescale/mpc8569mds/bcsr.h
index 179a54c..091b69c 100644
--- a/board/freescale/mpc8569mds/bcsr.h
+++ b/board/freescale/mpc8569mds/bcsr.h
@@ -72,6 +72,10 @@
#define BCSR16_UPC1_DEV2 0x02
+#define BCSR17_nUSBEN 0x80
+#define BCSR17_nUSBLOWSPD 0x40
+#define BCSR17_USBVCC 0x20
+#define BCSR17_USBMODE 0x10
#define BCSR17_FLASH_nWP 0x01
/*BCSR Utils functions*/
diff --git a/board/freescale/mpc8569mds/mpc8569mds.c b/board/freescale/mpc8569mds/mpc8569mds.c
index ef99a75..cdd7813 100644
--- a/board/freescale/mpc8569mds/mpc8569mds.c
+++ b/board/freescale/mpc8569mds/mpc8569mds.c
@@ -160,6 +160,15 @@ const qe_iop_conf_t qe_iop_conf_tab[] = {
{0, 25, 1, 0, 1}, /* QEUART_RTS */
{1, 23, 2, 0, 1}, /* QEUART_CTS */
+ /* QE USB */
+ {5, 3, 1, 0, 1}, /* USB_OE */
+ {5, 4, 1, 0, 2}, /* USB_TP */
+ {5, 5, 1, 0, 2}, /* USB_TN */
+ {5, 6, 2, 0, 2}, /* USB_RP */
+ {5, 7, 2, 0, 1}, /* USB_RX */
+ {5, 8, 2, 0, 1}, /* USB_RN */
+ {2, 4, 2, 0, 2}, /* CLK5 */
+
/* SPI Flash, M25P40 */
{4, 27, 3, 0, 1}, /* SPI_MOSI */
{4, 28, 3, 0, 1}, /* SPI_MISO */
@@ -479,6 +488,28 @@ static void fdt_board_fixup_esdhc(void *blob, bd_t *bd)
static inline void fdt_board_fixup_esdhc(void *blob, bd_t *bd) {}
#endif
+static void fdt_board_fixup_qe_usb(void *blob, bd_t *bd)
+{
+ u8 *bcsr = (u8 *)CONFIG_SYS_BCSR_BASE;
+
+ if (hwconfig_subarg_cmp("qe_usb", "speed", "low"))
+ clrbits_8(&bcsr[17], BCSR17_nUSBLOWSPD);
+ else
+ setbits_8(&bcsr[17], BCSR17_nUSBLOWSPD);
+
+ if (hwconfig_subarg_cmp("qe_usb", "mode", "peripheral")) {
+ clrbits_8(&bcsr[17], BCSR17_USBVCC);
+ clrbits_8(&bcsr[17], BCSR17_USBMODE);
+ do_fixup_by_compat(blob, "fsl,mpc8569-qe-usb", "mode",
+ "peripheral", sizeof("peripheral"), 1);
+ } else {
+ setbits_8(&bcsr[17], BCSR17_USBVCC);
+ setbits_8(&bcsr[17], BCSR17_USBMODE);
+ }
+
+ clrbits_8(&bcsr[17], BCSR17_nUSBEN);
+}
+
#ifdef CONFIG_PCIE1
static struct pci_controller pcie1_hose;
#endif /* CONFIG_PCIE1 */
@@ -622,5 +653,6 @@ void ft_board_setup(void *blob, bd_t *bd)
#endif
fdt_board_fixup_esdhc(blob, bd);
fdt_board_fixup_qe_uart(blob, bd);
+ fdt_board_fixup_qe_usb(blob, bd);
}
#endif
diff --git a/drivers/qe/fdt.c b/drivers/qe/fdt.c
index 5307488..d7c7d13 100644
--- a/drivers/qe/fdt.c
+++ b/drivers/qe/fdt.c
@@ -85,6 +85,8 @@ void ft_qe_setup(void *blob)
"bus-frequency", gd->qe_clk, 1);
do_fixup_by_compat_u32(blob, "fsl,qe",
"brg-frequency", gd->brg_clk, 1);
+ do_fixup_by_compat_u32(blob, "fsl,qe-gtm",
+ "clock-frequency", gd->qe_clk / 2, 1);
fdt_fixup_qe_firmware(blob);
#endif
}
--
1.6.3.3
next prev parent reply other threads:[~2009-10-15 13:47 UTC|newest]
Thread overview: 18+ messages / expand[flat|nested] mbox.gz Atom feed top
2009-10-15 13:46 [U-Boot] [PATCH 0/7] Some patches for MPC8569E-MDS Anton Vorontsov
2009-10-15 13:47 ` [U-Boot] [PATCH 1/7] fdt_support: Add multi-serial support for stdout fixup Anton Vorontsov
2009-10-22 14:24 ` Kumar Gala
2009-10-22 14:47 ` Jerry Van Baren
2009-10-27 2:39 ` Kumar Gala
2009-10-15 13:47 ` [U-Boot] [PATCH 2/7] mpc85xx: Add eSDHC support for MPC8569E-MDS boards Anton Vorontsov
2009-10-27 14:37 ` Kumar Gala
2009-10-15 13:47 ` [U-Boot] [PATCH 3/7] mpc85xx: Add eLBC NAND " Anton Vorontsov
2009-10-27 15:10 ` Kumar Gala
2009-10-15 13:47 ` [U-Boot] [PATCH 4/7] mpc85xx: Setup SRIO memory region LAW " Anton Vorontsov
2009-10-27 15:10 ` Kumar Gala
2009-10-15 13:47 ` [U-Boot] [PATCH 5/7] mpc85xx: Setup QE pinmux for SPI Flash on " Anton Vorontsov
2009-10-27 15:10 ` Kumar Gala
2009-10-15 13:47 ` [U-Boot] [PATCH 6/7] mpc85xx: Configure QE UART for " Anton Vorontsov
2009-10-27 15:10 ` Kumar Gala
2009-10-15 13:47 ` Anton Vorontsov [this message]
2009-10-27 15:10 ` [U-Boot] [PATCH 7/7] mpc85xx: Configure QE USB " Kumar Gala
-- strict thread matches above, loose matches on Subject: below --
2009-08-19 18:37 Anton Vorontsov
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20091015134716.GG32478@oksana.dev.rtsoft.ru \
--to=avorontsov@ru.mvista.com \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.