From: Patrick Finnegan <pat@computer-refuge.org>
To: sparclinux@vger.kernel.org
Subject: Re: Boot problems on a V880
Date: Sat, 28 Nov 2009 01:52:17 +0000 [thread overview]
Message-ID: <200911272052.17430.pat@computer-refuge.org> (raw)
In-Reply-To: <200911262202.45791.pat@computer-refuge.org>
On Friday 27 November 2009, David Miller wrote:
> From: Patrick Finnegan <pat@computer-refuge.org>
> Date: Thu, 26 Nov 2009 22:02:45 -0500
>
> > I seem to have a new/different problem with booting on a Sun V880.
> > I have tried Debian/sarge, etch, and lenny installers, each fails.
> > After reading through a bit of this list, I downloaded
> > sparc-next-2.6 via git, and compiled a kernel (based on
> > Debian/lenny's 2.6.26-2-sparc64 kernel config), and it still won't
> > boot. I also updated to the latest OpenBoot image, hoping that
> > would help, but I didn't see any difference.
>
> sparc-next-2.6 doesn't have the bug fix, sparc-2.6 does
Ok, with sparc-2.6, I get farther. If I pull the RSC card, it actually
gets to a point where it tries to mount the root filesystem (and fails,
because I don't have one for it yet). With the RSC in, it hangs after
the following output. I have tried this with the OpenBoot console set
to both ttya and rsc-console, and passed a "console=ttyS0" each time. At
the point that the machine hangs, it locks up hard enough that sending a
break doesn't send me to an "ok" prompt.
The RSC is running the newest (2.2.3) firmware, and works ok with
Solaris 10. Suggestions?
[ 0.000000] PROMLIB: Sun IEEE Boot Prom 'OBP 4.30.4 2009/08/19 07:21'
[ 0.000000] PROMLIB: Root node compatible:
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.32-rc3 (root@v210) (gcc version 4.3.4
(Debian 4.3.4-6) ) #1 SMP Fri Nov 27 20:17:53 EST 2009
[ 0.000000] bootconsole [earlyprom0] enabled
[ 0.000000] ARCH: SUN4U
[ 0.000000] Ethernet address: 00:03:ba:2f:1f:16
[ 0.000000] Kernel: Using 2 locked TLB entries for main kernel image.
[ 0.000000] Remapping the kernel... done.
[ 0.000000] OF stdout device is: /pci@9,700000/ebus@1/rsc-
console@1,3083f8
[ 0.000000] PROM: Built device tree with 160127 bytes of memory.
[ 0.000000] Top of RAM: 0xd0ffb18000, Total RAM: 0x3ff932000
[ 0.000000] Memory hole size: 839681MB
[ 0.000000] [0000010140000000-fffff8a000c00000] page_structs\x131072
node=0 entry\x1280/0
[ 0.000000] [0000010140000000-fffff8a001000000] page_structs\x131072
node=0 entry\x1281/0
[ 0.000000] [0000010140800000-fffff8a001400000] page_structs\x131072
node=0 entry\x1282/0
[ 0.000000] [0000010140800000-fffff8a001800000] page_structs\x131072
node=0 entry\x1283/0
[ 0.000000] [0000010141000000-fffff8a001c00000] page_structs\x131072
node=0 entry\x1284/0
[ 0.000000] [0000010141000000-fffff8a002000000] page_structs\x131072
node=0 entry\x1285/0
[ 0.000000] [0000010141800000-fffff8a002400000] page_structs\x131072
node=0 entry\x1286/0
[ 0.000000] [0000010141800000-fffff8a002800000] page_structs\x131072
node=0 entry\x1287/0
[ 0.000000] [0000010160000000-fffff8a002c00000] page_structs\x131072
node=0 entry\x1408/0
[ 0.000000] [0000010160000000-fffff8a003000000] page_structs\x131072
node=0 entry\x1409/0
[ 0.000000] [0000010160800000-fffff8a003400000] page_structs\x131072
node=0 entry\x1410/0
[ 0.000000] [0000010160800000-fffff8a003800000] page_structs\x131072
node=0 entry\x1411/0
[ 0.000000] [0000010161000000-fffff8a003c00000] page_structs\x131072
node=0 entry\x1412/0
[ 0.000000] [0000010161000000-fffff8a004000000] page_structs\x131072
node=0 entry\x1413/0
[ 0.000000] [0000010161800000-fffff8a004400000] page_structs\x131072
node=0 entry\x1414/0
[ 0.000000] [0000010161800000-fffff8a004800000] page_structs\x131072
node=0 entry\x1415/0
[ 0.000000] [0000010180000000-fffff8a004c00000] page_structs\x131072
node=0 entry\x1536/0
[ 0.000000] [0000010180000000-fffff8a005000000] page_structs\x131072
node=0 entry\x1537/0
[ 0.000000] [0000010180800000-fffff8a005400000] page_structs\x131072
node=0 entry\x1538/0
[ 0.000000] [0000010180800000-fffff8a005800000] page_structs\x131072
node=0 entry\x1539/0
[ 0.000000] [0000010181000000-fffff8a005c00000] page_structs\x131072
node=0 entry\x1540/0
[ 0.000000] [0000010181000000-fffff8a006000000] page_structs\x131072
node=0 entry\x1541/0
[ 0.000000] [0000010181800000-fffff8a006400000] page_structs\x131072
node=0 entry\x1542/0
[ 0.000000] [0000010181800000-fffff8a006800000] page_structs\x131072
node=0 entry\x1543/0
[ 0.000000] [00000101a0000000-fffff8a006c00000] page_structs\x131072
node=0 entry\x1664/0
[ 0.000000] [00000101a0000000-fffff8a007000000] page_structs\x131072
node=0 entry\x1665/0
[ 0.000000] [00000101a0800000-fffff8a007400000] page_structs\x131072
node=0 entry\x1666/0
[ 0.000000] [00000101a0800000-fffff8a007800000] page_structs\x131072
node=0 entry\x1667/0
[ 0.000000] [00000101a1000000-fffff8a007c00000] page_structs\x131072
node=0 entry\x1668/0
[ 0.000000] [00000101a1000000-fffff8a008000000] page_structs\x131072
node=0 entry\x1669/0
[ 0.000000] [00000101a1800000-fffff8a008400000] page_structs\x131072
node=0 entry\x1670/0
[ 0.000000] [00000101a1800000-fffff8a008800000] page_structs\x131072
node=0 entry\x1671/0
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x05000000 -> 0x0687fd8c
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[7] active PFN ranges
[ 0.000000] 0: 0x05000000 -> 0x05080000
[ 0.000000] 0: 0x05800000 -> 0x05880000
[ 0.000000] 0: 0x06000000 -> 0x06080000
[ 0.000000] 0: 0x06800000 -> 0x0687f7ff
[ 0.000000] 0: 0x0687f800 -> 0x0687fc3d
[ 0.000000] 0: 0x0687fd0a -> 0x0687fd58
[ 0.000000] 0: 0x0687fd7d -> 0x0687fd8c
[ 0.000000] Booting Linux...
[ 0.000000] PERCPU: Embedded 7 pages/cpu @fffff8a008c00000 s22336
r8192 d26816 u524288
[ 0.000000] pcpu-alloc: s22336 r8192 d26816 u524288 alloc=1*4194304
[ 0.000000] pcpu-alloc: [0] 0 1 2 3 4 5 6 7
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.
Total pages: 1895581
[ 0.000000] Kernel command line: console=ttyS0
[ 0.000000] PID hash table entries: 4096 (order: 2, 32768 bytes)
[ 0.000000] Dentry cache hash table entries: 2097152 (order: 11,
16777216 bytes)
[ 0.000000] Inode-cache hash table entries: 1048576 (order: 10,
8388608 bytes)
[ 0.000000] Memory: 16607592k available (2968k kernel code, 1176k
data, 208k init) [fffff80000000000,000000d0ffb18000]
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:255
[ 0.000000] clocksource: mult[640000] shift[16]
[ 0.000000] clockevent: mult[28f5c28] shift[32]
[ 0.000000] Console: colour dummy device 80x25
[ 102.564500] Calibrating delay using timer specific routine.. 20.01
BogoMIPS (lpj@029)
[ 102.572566] Security Framework initialized
[ 102.576685] Mount-cache hash table entries: 512
[ 102.581616] Initializing cgroup subsys ns
[ 102.585577] Initializing cgroup subsys cpuacct
[ 102.589994] Initializing cgroup subsys devices
[ 102.594406] Initializing cgroup subsys freezer
[ 102.600982] CPU 0: synchronized TICK with master CPU (last diff 0
cycles, maxerr 11 cycles)
[ 102.602558] CPU 1: synchronized TICK with master CPU (last diff 0
cycles, maxerr 11 cycles)
[ 102.609412] CPU 2: synchronized TICK with master CPU (last diff 0
cycles, maxerr 11 cycles)
[ 102.610980] CPU 3: synchronized TICK with master CPU (last diff 0
cycles, maxerr 12 cycles)
[ 102.620436] CPU 4: synchronized TICK with master CPU (last diff 0
cycles, maxerr 11 cycles)
[ 102.621985] CPU 5: synchronized TICK with master CPU (last diff 0
cycles, maxerr 11 cycles)
[ 102.629802] CPU 6: synchronized TICK with master CPU (last diff 0
cycles, maxerr 11 cycles)
[ 102.629818] Brought up 8 CPUs
[ 102.666637] regulator: core version 0.5
[ 102.670746] NET: Registered protocol family 16
[ 102.704507] Testing NMI watchdog ... OK.
[ 102.788369] Performance events: Supported PMU type is 'ultra3+'
[ 102.797454] /pci@8,700000: SCHIZO PCI Bus Module ver[4:0]
[ 102.802925] /pci@8,700000: PCI IO[7ffef000000] MEM[7fe00000000]
[ 102.813439] PCI: Scanning PBM /pci@8,700000
[ 102.818155] /pci@8,600000: SCHIZO PCI Bus Module ver[4:0]
[ 102.823614] /pci@8,600000: PCI IO[7ffed000000] MEM[7fd00000000]
[ 102.834067] PCI: Scanning PBM /pci@8,600000
[ 102.839121] /pci@9,700000: SCHIZO PCI Bus Module ver[4:0]
[ 102.844506] /pci@9,700000: PCI IO[7ffeb000000] MEM[7fc00000000]
[ 102.854977] PCI: Scanning PBM /pci@9,700000
[ 102.864365] /pci@9,600000: SCHIZO PCI Bus Module ver[4:0]
[ 102.869711] /pci@9,600000: PCI IO[7ffe9000000] MEM[7fb00000000]
[ 102.880231] PCI: Scanning PBM /pci@9,600000
[ 102.893534] bio: create slab <bio-0> at 0
[ 102.898719] vgaarb: loaded
[ 102.903089] /pci@9,700000/ebus@1/rtc@1,300070: RTC regs at
0x7fc7e300070
[ 102.910914] Switching to clocksource stick
[ 102.924074] NET: Registered protocol family 2
[ 102.928859] IP route cache hash table entries: 524288 (order: 9,
4194304 bytes)
[ 102.941163] TCP established hash table entries: 524288 (order: 10,
8388608 bytes)
[ 102.979862] TCP bind hash table entries: 65536 (order: 7, 1048576
bytes)
[ 102.990442] TCP: Hash tables configured (established 524288 bind
65536)
[ 102.996998] TCP reno registered
[ 103.000698] NET: Registered protocol family 1
[ 103.005402] power: Control reg at 7fc7e30002e
[ 103.010321] chmc: UltraSPARC-III memory controller at /memory-
controller@0,400000 [ACTIVE]
[ 103.018579] chmc: UltraSPARC-III memory controller at /memory-
controller@1,400000 [ACTIVE]
[ 103.026807] chmc: UltraSPARC-III memory controller at /memory-
controller@2,400000 [ACTIVE]
[ 103.035034] chmc: UltraSPARC-III memory controller at /memory-
controller@3,400000 [ACTIVE]
[ 103.043264] chmc: UltraSPARC-III memory controller at /memory-
controller@4,400000 [ACTIVE]
[ 103.051505] chmc: UltraSPARC-III memory controller at /memory-
controller@5,400000 [ACTIVE]
[ 103.059732] chmc: UltraSPARC-III memory controller at /memory-
controller@6,400000 [ACTIVE]
[ 103.067970] chmc: UltraSPARC-III memory controller at /memory-
controller@7,400000 [ACTIVE]
[ 103.077213] audit: initializing netlink socket (disabled)
[ 103.082589] type 00 audit(0.559:1): initialized
Pat
--
Purdue University Research Computing --- http://www.rcac.purdue.edu/
The Computer Refuge --- http://computer-refuge.org
next prev parent reply other threads:[~2009-11-28 1:52 UTC|newest]
Thread overview: 11+ messages / expand[flat|nested] mbox.gz Atom feed top
2009-11-27 3:02 Boot problems on a V880 Patrick Finnegan
2009-11-27 7:30 ` David Miller
2009-11-28 1:52 ` Patrick Finnegan [this message]
2009-11-28 2:30 ` David Miller
2009-11-28 3:07 ` Patrick Finnegan
2009-11-30 21:02 ` Patrick Finnegan
2009-11-30 21:05 ` David Miller
2009-12-01 4:04 ` Patrick Finnegan
2009-12-01 5:48 ` David Miller
2009-12-03 6:48 ` Patrick Finnegan
2009-12-03 6:56 ` David Miller
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=200911272052.17430.pat@computer-refuge.org \
--to=pat@computer-refuge.org \
--cc=sparclinux@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.