* [PATCH 1/3] ARM: cns3xxx: Add basic support for Cavium Networks CNS3xxx processors
2010-03-26 19:23 [PATCH v2 0/3] Support for Cavium Networks CNS3xxx machines Anton Vorontsov
@ 2010-03-26 19:23 ` Anton Vorontsov
2010-03-26 19:23 ` [PATCH 2/3] ARM: cns3xxx: Add CNS3420 Validation Board support Anton Vorontsov
2010-03-26 19:23 ` [PATCH 3/3] ARM: cns3xxx: Add defconfig for CNS3420 validation board Anton Vorontsov
2 siblings, 0 replies; 4+ messages in thread
From: Anton Vorontsov @ 2010-03-26 19:23 UTC (permalink / raw)
To: linux-arm-kernel
This patch adds very basic support for ECONA CNS3xxx ARM11 MPcore
(ARMv6) dual-core processors.
Note that SMP is not yet supported, as well as many peripheral
devices. Support for these features will be added later.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
---
MAINTAINERS | 6 +
arch/arm/Kconfig | 11 +
arch/arm/Makefile | 1 +
arch/arm/mach-cns3xxx/Kconfig | 4 +
arch/arm/mach-cns3xxx/Makefile | 1 +
arch/arm/mach-cns3xxx/Makefile.boot | 3 +
arch/arm/mach-cns3xxx/core.c | 285 ++++++++++
arch/arm/mach-cns3xxx/core.h | 23 +
arch/arm/mach-cns3xxx/include/mach/cns3xxx.h | 655 ++++++++++++++++++++++
arch/arm/mach-cns3xxx/include/mach/debug-macro.S | 21 +
arch/arm/mach-cns3xxx/include/mach/entry-macro.S | 82 +++
arch/arm/mach-cns3xxx/include/mach/hardware.h | 22 +
arch/arm/mach-cns3xxx/include/mach/io.h | 22 +
arch/arm/mach-cns3xxx/include/mach/irqs.h | 24 +
arch/arm/mach-cns3xxx/include/mach/memory.h | 26 +
arch/arm/mach-cns3xxx/include/mach/system.h | 29 +
arch/arm/mach-cns3xxx/include/mach/timex.h | 12 +
arch/arm/mach-cns3xxx/include/mach/uncompress.h | 55 ++
arch/arm/mach-cns3xxx/include/mach/vmalloc.h | 11 +
arch/arm/mach-cns3xxx/pm.c | 86 +++
20 files changed, 1379 insertions(+), 0 deletions(-)
create mode 100644 arch/arm/mach-cns3xxx/Kconfig
create mode 100644 arch/arm/mach-cns3xxx/Makefile
create mode 100644 arch/arm/mach-cns3xxx/Makefile.boot
create mode 100644 arch/arm/mach-cns3xxx/core.c
create mode 100644 arch/arm/mach-cns3xxx/core.h
create mode 100644 arch/arm/mach-cns3xxx/include/mach/cns3xxx.h
create mode 100644 arch/arm/mach-cns3xxx/include/mach/debug-macro.S
create mode 100644 arch/arm/mach-cns3xxx/include/mach/entry-macro.S
create mode 100644 arch/arm/mach-cns3xxx/include/mach/hardware.h
create mode 100644 arch/arm/mach-cns3xxx/include/mach/io.h
create mode 100644 arch/arm/mach-cns3xxx/include/mach/irqs.h
create mode 100644 arch/arm/mach-cns3xxx/include/mach/memory.h
create mode 100644 arch/arm/mach-cns3xxx/include/mach/system.h
create mode 100644 arch/arm/mach-cns3xxx/include/mach/timex.h
create mode 100644 arch/arm/mach-cns3xxx/include/mach/uncompress.h
create mode 100644 arch/arm/mach-cns3xxx/include/mach/vmalloc.h
create mode 100644 arch/arm/mach-cns3xxx/pm.c
diff --git a/MAINTAINERS b/MAINTAINERS
index 449d444..93ebdf8 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -586,6 +586,12 @@ F: drivers/mtd/nand/bcm_umi_bch.c
F: drivers/mtd/nand/bcm_umi_hamming.c
F: drivers/mtd/nand/nand_bcm_umi.h
+ARM/CAVIUM NETWORKS CNS3XXX MACHINE SUPPORT
+M: Anton Vorontsov <avorontsov@mvista.com>
+S: Maintained
+F: arch/arm/mach-cns3xxx/
+T: git git://git.infradead.org/users/cbou/linux-cns3xxx.git
+
ARM/CIRRUS LOGIC EP93XX ARM ARCHITECTURE
M: Hartley Sweeten <hsweeten@visionengravers.com>
M: Ryan Mallon <ryan@bluewatersys.com>
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index c5408bf..d779e25 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -296,6 +296,15 @@ config ARCH_CLPS711X
help
Support for Cirrus Logic 711x/721x based boards.
+config ARCH_CNS3XXX
+ bool "Cavium Networks CNS3XXX family"
+ select CPU_V6
+ select GENERIC_TIME
+ select GENERIC_CLOCKEVENTS
+ select ARM_GIC
+ help
+ Support for Cavium Networks CNS3XXX platform.
+
config ARCH_GEMINI
bool "Cortina Systems Gemini"
select CPU_FA526
@@ -816,6 +825,8 @@ source "arch/arm/mach-bcmring/Kconfig"
source "arch/arm/mach-clps711x/Kconfig"
+source "arch/arm/mach-cns3xxx/Kconfig"
+
source "arch/arm/mach-davinci/Kconfig"
source "arch/arm/mach-dove/Kconfig"
diff --git a/arch/arm/Makefile b/arch/arm/Makefile
index ed820e7..3e312ec 100644
--- a/arch/arm/Makefile
+++ b/arch/arm/Makefile
@@ -121,6 +121,7 @@ machine-$(CONFIG_ARCH_AAEC2000) := aaec2000
machine-$(CONFIG_ARCH_AT91) := at91
machine-$(CONFIG_ARCH_BCMRING) := bcmring
machine-$(CONFIG_ARCH_CLPS711X) := clps711x
+machine-$(CONFIG_ARCH_CNS3XXX) := cns3xxx
machine-$(CONFIG_ARCH_DAVINCI) := davinci
machine-$(CONFIG_ARCH_DOVE) := dove
machine-$(CONFIG_ARCH_EBSA110) := ebsa110
diff --git a/arch/arm/mach-cns3xxx/Kconfig b/arch/arm/mach-cns3xxx/Kconfig
new file mode 100644
index 0000000..20284cd
--- /dev/null
+++ b/arch/arm/mach-cns3xxx/Kconfig
@@ -0,0 +1,4 @@
+menu "CNS3XXX platform type"
+ depends on ARCH_CNS3XXX
+
+endmenu
diff --git a/arch/arm/mach-cns3xxx/Makefile b/arch/arm/mach-cns3xxx/Makefile
new file mode 100644
index 0000000..e5e76dd
--- /dev/null
+++ b/arch/arm/mach-cns3xxx/Makefile
@@ -0,0 +1 @@
+obj-$(CONFIG_ARCH_CNS3XXX) += core.o pm.o
diff --git a/arch/arm/mach-cns3xxx/Makefile.boot b/arch/arm/mach-cns3xxx/Makefile.boot
new file mode 100644
index 0000000..7770128
--- /dev/null
+++ b/arch/arm/mach-cns3xxx/Makefile.boot
@@ -0,0 +1,3 @@
+ zreladdr-y := 0x00008000
+params_phys-y := 0x00000100
+initrd_phys-y := 0x00C00000
diff --git a/arch/arm/mach-cns3xxx/core.c b/arch/arm/mach-cns3xxx/core.c
new file mode 100644
index 0000000..4859cec
--- /dev/null
+++ b/arch/arm/mach-cns3xxx/core.c
@@ -0,0 +1,285 @@
+/*
+ * Copyright 1999 - 2003 ARM Limited
+ * Copyright 2000 Deep Blue Solutions Ltd
+ * Copyright 2008 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/clocksource.h>
+#include <linux/clockchips.h>
+#include <linux/io.h>
+#include <asm/mach/map.h>
+#include <asm/mach/time.h>
+#include <asm/mach/irq.h>
+#include <asm/hardware/gic.h>
+#include <mach/cns3xxx.h>
+#include "core.h"
+
+static struct map_desc cns3xxx_io_desc[] __initdata = {
+ {
+ .virtual = CNS3XXX_TC11MP_TWD_BASE_VIRT,
+ .pfn = __phys_to_pfn(CNS3XXX_TC11MP_TWD_BASE),
+ .length = SZ_4K,
+ .type = MT_DEVICE,
+ }, {
+ .virtual = CNS3XXX_TC11MP_GIC_CPU_BASE_VIRT,
+ .pfn = __phys_to_pfn(CNS3XXX_TC11MP_GIC_CPU_BASE),
+ .length = SZ_4K,
+ .type = MT_DEVICE,
+ }, {
+ .virtual = CNS3XXX_TC11MP_GIC_DIST_BASE_VIRT,
+ .pfn = __phys_to_pfn(CNS3XXX_TC11MP_GIC_DIST_BASE),
+ .length = SZ_4K,
+ .type = MT_DEVICE,
+ }, {
+ .virtual = CNS3XXX_TIMER1_2_3_BASE_VIRT,
+ .pfn = __phys_to_pfn(CNS3XXX_TIMER1_2_3_BASE),
+ .length = SZ_4K,
+ .type = MT_DEVICE,
+ }, {
+ .virtual = CNS3XXX_GPIOA_BASE_VIRT,
+ .pfn = __phys_to_pfn(CNS3XXX_GPIOA_BASE),
+ .length = SZ_4K,
+ .type = MT_DEVICE,
+ }, {
+ .virtual = CNS3XXX_GPIOB_BASE_VIRT,
+ .pfn = __phys_to_pfn(CNS3XXX_GPIOB_BASE),
+ .length = SZ_4K,
+ .type = MT_DEVICE,
+ }, {
+ .virtual = CNS3XXX_MISC_BASE_VIRT,
+ .pfn = __phys_to_pfn(CNS3XXX_MISC_BASE),
+ .length = SZ_4K,
+ .type = MT_DEVICE,
+ }, {
+ .virtual = CNS3XXX_PM_BASE_VIRT,
+ .pfn = __phys_to_pfn(CNS3XXX_PM_BASE),
+ .length = SZ_4K,
+ .type = MT_DEVICE,
+ },
+};
+
+void __init cns3xxx_map_io(void)
+{
+ iotable_init(cns3xxx_io_desc, ARRAY_SIZE(cns3xxx_io_desc));
+}
+
+/* used by entry-macro.S */
+void __iomem *gic_cpu_base_addr;
+
+void __init cns3xxx_init_irq(void)
+{
+ gic_cpu_base_addr = __io(CNS3XXX_TC11MP_GIC_CPU_BASE_VIRT);
+ gic_dist_init(0, __io(CNS3XXX_TC11MP_GIC_DIST_BASE_VIRT), 29);
+ gic_cpu_init(0, gic_cpu_base_addr);
+}
+
+void cns3xxx_power_off(void)
+{
+ u32 __iomem *pm_base = __io(CNS3XXX_PM_BASE_VIRT);
+ u32 clkctrl;
+
+ printk(KERN_INFO "powering system down...\n");
+
+ clkctrl = readl(pm_base + PM_SYS_CLK_CTRL_OFFSET);
+ clkctrl &= 0xfffff1ff;
+ clkctrl |= (0x5 << 9); /* Hibernate */
+ writel(clkctrl, pm_base + PM_SYS_CLK_CTRL_OFFSET);
+
+}
+
+/*
+ * Timer
+ */
+static void __iomem *cns3xxx_tmr1;
+
+static void cns3xxx_timer_set_mode(enum clock_event_mode mode,
+ struct clock_event_device *clk)
+{
+ unsigned long ctrl = readl(cns3xxx_tmr1 + TIMER1_2_CONTROL_OFFSET);
+ int pclk = cns3xxx_cpu_clock() / 8;
+ int reload;
+
+ switch (mode) {
+ case CLOCK_EVT_MODE_PERIODIC:
+ reload = pclk * 20 / (3 * HZ) * 0x25000;
+ writel(reload, cns3xxx_tmr1 + TIMER1_AUTO_RELOAD_OFFSET);
+ ctrl |= (1 << 0) | (1 << 2) | (1 << 9);
+ break;
+ case CLOCK_EVT_MODE_ONESHOT:
+ /* period set, and timer enabled in 'next_event' hook */
+ ctrl |= (1 << 2) | (1 << 9);
+ break;
+ case CLOCK_EVT_MODE_UNUSED:
+ case CLOCK_EVT_MODE_SHUTDOWN:
+ default:
+ ctrl = 0;
+ }
+
+ writel(ctrl, cns3xxx_tmr1 + TIMER1_2_CONTROL_OFFSET);
+}
+
+static int cns3xxx_timer_set_next_event(unsigned long evt,
+ struct clock_event_device *unused)
+{
+ unsigned long ctrl = readl(cns3xxx_tmr1 + TIMER1_2_CONTROL_OFFSET);
+
+ writel(evt, cns3xxx_tmr1 + TIMER1_AUTO_RELOAD_OFFSET);
+ writel(ctrl | (1 << 0), cns3xxx_tmr1 + TIMER1_2_CONTROL_OFFSET);
+
+ return 0;
+}
+
+static struct clock_event_device cns3xxx_tmr1_clockevent = {
+ .name = "cns3xxx timer1",
+ .shift = 8,
+ .features = CLOCK_EVT_FEAT_PERIODIC | CLOCK_EVT_FEAT_ONESHOT,
+ .set_mode = cns3xxx_timer_set_mode,
+ .set_next_event = cns3xxx_timer_set_next_event,
+ .rating = 350,
+ .cpumask = cpu_all_mask,
+};
+
+static void __init cns3xxx_clockevents_init(unsigned int timer_irq)
+{
+ cns3xxx_tmr1_clockevent.irq = timer_irq;
+ cns3xxx_tmr1_clockevent.mult =
+ div_sc((cns3xxx_cpu_clock() >> 3) * 1000000, NSEC_PER_SEC,
+ cns3xxx_tmr1_clockevent.shift);
+ cns3xxx_tmr1_clockevent.max_delta_ns =
+ clockevent_delta2ns(0xffffffff, &cns3xxx_tmr1_clockevent);
+ cns3xxx_tmr1_clockevent.min_delta_ns =
+ clockevent_delta2ns(0xf, &cns3xxx_tmr1_clockevent);
+
+ clockevents_register_device(&cns3xxx_tmr1_clockevent);
+}
+
+/*
+ * IRQ handler for the timer
+ */
+static irqreturn_t cns3xxx_timer_interrupt(int irq, void *dev_id)
+{
+ struct clock_event_device *evt = &cns3xxx_tmr1_clockevent;
+ u32 __iomem *stat = cns3xxx_tmr1 + TIMER1_2_INTERRUPT_STATUS_OFFSET;
+ u32 val;
+
+ /* Clear the interrupt */
+ val = readl(stat);
+ writel(val & ~(1 << 2), stat);
+
+ evt->event_handler(evt);
+
+ return IRQ_HANDLED;
+}
+
+static struct irqaction cns3xxx_timer_irq = {
+ .name = "timer",
+ .flags = IRQF_DISABLED | IRQF_TIMER | IRQF_IRQPOLL,
+ .handler = cns3xxx_timer_interrupt,
+};
+
+static cycle_t cns3xxx_get_cycles(struct clocksource *cs)
+{
+ return ~readl(cns3xxx_tmr1 + TIMER2_COUNTER_OFFSET);
+}
+
+static struct clocksource cns3xxx_clocksource = {
+ .name = "cns3xxx timer2",
+ .rating = 200,
+ .read = cns3xxx_get_cycles,
+ .mask = CLOCKSOURCE_MASK(32),
+ .shift = 20,
+ .flags = CLOCK_SOURCE_IS_CONTINUOUS,
+};
+
+static void __init cns3xxx_clocksource_init(void)
+{
+ u32 val;
+
+ /* let timer2 as periodic free-running clocksource, interrupt disable */
+ val = readl(cns3xxx_tmr1 + TIMER1_2_CONTROL_OFFSET);
+ val &= ~((1 << 3) | (1 << 4) | (1 << 5));
+ writel(val, cns3xxx_tmr1 + TIMER1_2_CONTROL_OFFSET);
+
+ writel(0x5C800, cns3xxx_tmr1 + TIMER2_COUNTER_OFFSET);
+ writel(0x5C800, cns3xxx_tmr1 + TIMER2_AUTO_RELOAD_OFFSET);
+
+ val = readl(cns3xxx_tmr1 + TIMER1_2_CONTROL_OFFSET);
+ writel(val | (1 << 3), cns3xxx_tmr1 + TIMER1_2_CONTROL_OFFSET);
+
+ cns3xxx_clocksource.mult =
+ clocksource_khz2mult(1000, cns3xxx_clocksource.shift);
+ clocksource_register(&cns3xxx_clocksource);
+}
+
+/*
+ * Set up the clock source and clock events devices
+ */
+static void __init __cns3xxx_timer_init(unsigned int timer_irq)
+{
+ u32 val;
+ u32 irq_mask;
+
+ /*
+ * Initialise to a known state (all timers off)
+ */
+
+ /* disable timer1 and timer2 */
+ writel(0, cns3xxx_tmr1 + TIMER1_2_CONTROL_OFFSET);
+ /* stop free running timer3 */
+ writel(0, cns3xxx_tmr1 + TIMER_FREERUN_CONTROL_OFFSET);
+
+ /* timer1 */
+ writel(0x5C800, cns3xxx_tmr1 + TIMER1_COUNTER_OFFSET);
+ writel(0x5C800, cns3xxx_tmr1 + TIMER1_AUTO_RELOAD_OFFSET);
+
+ writel(0, cns3xxx_tmr1 + TIMER1_MATCH_V1_OFFSET);
+ writel(0, cns3xxx_tmr1 + TIMER1_MATCH_V2_OFFSET);
+
+ /* mask irq, non-mask timer1 overflow */
+ irq_mask = readl(cns3xxx_tmr1 + TIMER1_2_INTERRUPT_MASK_OFFSET);
+ irq_mask &= ~(1 << 2);
+ irq_mask |= 0x03;
+ writel(irq_mask, cns3xxx_tmr1 + TIMER1_2_INTERRUPT_MASK_OFFSET);
+
+ /* down counter */
+ val = readl(cns3xxx_tmr1 + TIMER1_2_CONTROL_OFFSET);
+ val |= (1 << 9);
+ writel(val, cns3xxx_tmr1 + TIMER1_2_CONTROL_OFFSET);
+
+ /* timer2 */
+ writel(0, cns3xxx_tmr1 + TIMER2_MATCH_V1_OFFSET);
+ writel(0, cns3xxx_tmr1 + TIMER2_MATCH_V2_OFFSET);
+
+ /* mask irq */
+ irq_mask = readl(cns3xxx_tmr1 + TIMER1_2_INTERRUPT_MASK_OFFSET);
+ irq_mask |= ((1 << 3) | (1 << 4) | (1 << 5));
+ writel(irq_mask, cns3xxx_tmr1 + TIMER1_2_INTERRUPT_MASK_OFFSET);
+
+ /* down counter */
+ val = readl(cns3xxx_tmr1 + TIMER1_2_CONTROL_OFFSET);
+ val |= (1 << 10);
+ writel(val, cns3xxx_tmr1 + TIMER1_2_CONTROL_OFFSET);
+
+ /* Make irqs happen for the system timer */
+ setup_irq(timer_irq, &cns3xxx_timer_irq);
+
+ cns3xxx_clocksource_init();
+ cns3xxx_clockevents_init(timer_irq);
+}
+
+static void __init cns3xxx_timer_init(void)
+{
+ cns3xxx_tmr1 = __io(CNS3XXX_TIMER1_2_3_BASE_VIRT);
+
+ __cns3xxx_timer_init(IRQ_CNS3XXX_TIMER0);
+}
+
+struct sys_timer cns3xxx_timer = {
+ .init = cns3xxx_timer_init,
+};
diff --git a/arch/arm/mach-cns3xxx/core.h b/arch/arm/mach-cns3xxx/core.h
new file mode 100644
index 0000000..6b33ec1
--- /dev/null
+++ b/arch/arm/mach-cns3xxx/core.h
@@ -0,0 +1,23 @@
+/*
+ * Copyright 2000 Deep Blue Solutions Ltd
+ * Copyright 2004 ARM Limited
+ * Copyright 2008 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef __CNS3XXX_CORE_H
+#define __CNS3XXX_CORE_H
+
+extern void __iomem *gic_cpu_base_addr;
+extern struct sys_timer cns3xxx_timer;
+
+void __init cns3xxx_map_io(void);
+void __init cns3xxx_init_irq(void);
+void cns3xxx_power_off(void);
+void cns3xxx_pwr_power_up(unsigned int block);
+void cns3xxx_pwr_power_down(unsigned int block);
+
+#endif /* __CNS3XXX_CORE_H */
diff --git a/arch/arm/mach-cns3xxx/include/mach/cns3xxx.h b/arch/arm/mach-cns3xxx/include/mach/cns3xxx.h
new file mode 100644
index 0000000..3e71bce
--- /dev/null
+++ b/arch/arm/mach-cns3xxx/include/mach/cns3xxx.h
@@ -0,0 +1,655 @@
+/*
+ * Copyright 2008 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef __MACH_BOARD_CNS3XXXH
+#define __MACH_BOARD_CNS3XXXH
+
+/*
+ * Memory map
+ */
+#define CNS3XXX_FLASH_BASE 0x10000000 /* Flash/SRAM Memory Bank 0 */
+#define CNS3XXX_FLASH_SIZE SZ_256M
+
+#define CNS3XXX_DDR2SDRAM_BASE 0x20000000 /* DDR2 SDRAM Memory */
+
+#define CNS3XXX_SPI_FLASH_BASE 0x60000000 /* SPI Serial Flash Memory */
+
+#define CNS3XXX_SWITCH_BASE 0x70000000 /* Switch and HNAT Control */
+#define CNS3XXX_SWITCH_BASE_VIRT 0xFFF00000
+
+#define CNS3XXX_PPE_BASE 0x70001000 /* HANT */
+#define CNS3XXX_PPE_BASE_VIRT 0xFFF50000
+
+#define CNS3XXX_EMBEDDED_SRAM_BASE 0x70002000 /* HANT Embedded SRAM */
+#define CNS3XXX_EMBEDDED_SRAM_BASE_VIRT 0xFFF60000
+
+#define CNS3XXX_SSP_BASE 0x71000000 /* Synchronous Serial Port - SPI/PCM/I2C */
+#define CNS3XXX_SSP_BASE_VIRT 0xFFF01000
+
+#define CNS3XXX_DMC_BASE 0x72000000 /* DMC Control (DDR2 SDRAM) */
+#define CNS3XXX_DMC_BASE_VIRT 0xFFF02000
+
+#define CNS3XXX_SMC_BASE 0x73000000 /* SMC Control */
+#define CNS3XXX_SMC_BASE_VIRT 0xFFF03000
+
+#define SMC_MEMC_STATUS_OFFSET 0x000
+#define SMC_MEMIF_CFG_OFFSET 0x004
+#define SMC_MEMC_CFG_SET_OFFSET 0x008
+#define SMC_MEMC_CFG_CLR_OFFSET 0x00C
+#define SMC_DIRECT_CMD_OFFSET 0x010
+#define SMC_SET_CYCLES_OFFSET 0x014
+#define SMC_SET_OPMODE_OFFSET 0x018
+#define SMC_REFRESH_PERIOD_0_OFFSET 0x020
+#define SMC_REFRESH_PERIOD_1_OFFSET 0x024
+#define SMC_SRAM_CYCLES0_0_OFFSET 0x100
+#define SMC_NAND_CYCLES0_0_OFFSET 0x100
+#define SMC_OPMODE0_0_OFFSET 0x104
+#define SMC_SRAM_CYCLES0_1_OFFSET 0x120
+#define SMC_NAND_CYCLES0_1_OFFSET 0x120
+#define SMC_OPMODE0_1_OFFSET 0x124
+#define SMC_USER_STATUS_OFFSET 0x200
+#define SMC_USER_CONFIG_OFFSET 0x204
+#define SMC_ECC_STATUS_OFFSET 0x300
+#define SMC_ECC_MEMCFG_OFFSET 0x304
+#define SMC_ECC_MEMCOMMAND1_OFFSET 0x308
+#define SMC_ECC_MEMCOMMAND2_OFFSET 0x30C
+#define SMC_ECC_ADDR0_OFFSET 0x310
+#define SMC_ECC_ADDR1_OFFSET 0x314
+#define SMC_ECC_VALUE0_OFFSET 0x318
+#define SMC_ECC_VALUE1_OFFSET 0x31C
+#define SMC_ECC_VALUE2_OFFSET 0x320
+#define SMC_ECC_VALUE3_OFFSET 0x324
+#define SMC_PERIPH_ID_0_OFFSET 0xFE0
+#define SMC_PERIPH_ID_1_OFFSET 0xFE4
+#define SMC_PERIPH_ID_2_OFFSET 0xFE8
+#define SMC_PERIPH_ID_3_OFFSET 0xFEC
+#define SMC_PCELL_ID_0_OFFSET 0xFF0
+#define SMC_PCELL_ID_1_OFFSET 0xFF4
+#define SMC_PCELL_ID_2_OFFSET 0xFF8
+#define SMC_PCELL_ID_3_OFFSET 0xFFC
+
+#define CNS3XXX_GPIOA_BASE 0x74000000 /* GPIO port A */
+#define CNS3XXX_GPIOA_BASE_VIRT 0xFFF04000
+
+#define CNS3XXX_GPIOB_BASE 0x74800000 /* GPIO port B */
+#define CNS3XXX_GPIOB_BASE_VIRT 0xFFF05000
+
+#define CNS3XXX_RTC_BASE 0x75000000 /* Real Time Clock */
+#define CNS3XXX_RTC_BASE_VIRT 0xFFF06000
+
+#define RTC_SEC_OFFSET 0x00
+#define RTC_MIN_OFFSET 0x04
+#define RTC_HOUR_OFFSET 0x08
+#define RTC_DAY_OFFSET 0x0C
+#define RTC_SEC_ALM_OFFSET 0x10
+#define RTC_MIN_ALM_OFFSET 0x14
+#define RTC_HOUR_ALM_OFFSET 0x18
+#define RTC_REC_OFFSET 0x1C
+#define RTC_CTRL_OFFSET 0x20
+#define RTC_INTR_STS_OFFSET 0x34
+
+#define CNS3XXX_MISC_BASE 0x76000000 /* Misc Control */
+#define CNS3XXX_MISC_BASE_VIRT 0xFFF07000 /* Misc Control */
+
+#define CNS3XXX_PM_BASE 0x77000000 /* Power Management Control */
+#define CNS3XXX_PM_BASE_VIRT 0xFFF08000
+
+#define PM_CLK_GATE_OFFSET 0x00
+#define PM_SOFT_RST_OFFSET 0x04
+#define PM_HS_CFG_OFFSET 0x08
+#define PM_CACTIVE_STA_OFFSET 0x0C
+#define PM_PWR_STA_OFFSET 0x10
+#define PM_SYS_CLK_CTRL_OFFSET 0x14
+#define PM_PLL_LCD_I2S_CTRL_OFFSET 0x18
+#define PM_PLL_HM_PD_OFFSET 0x1C
+
+#define CNS3XXX_UART0_BASE 0x78000000 /* UART 0 */
+#define CNS3XXX_UART0_BASE_VIRT 0xFFF09000
+
+#define CNS3XXX_UART1_BASE 0x78400000 /* UART 1 */
+#define CNS3XXX_UART1_BASE_VIRT 0xFFF0A000
+
+#define CNS3XXX_UART2_BASE 0x78800000 /* UART 2 */
+#define CNS3XXX_UART2_BASE_VIRT 0xFFF0B000
+
+#define CNS3XXX_DMAC_BASE 0x79000000 /* Generic DMA Control */
+#define CNS3XXX_DMAC_BASE_VIRT 0xFFF0D000
+
+#define CNS3XXX_CORESIGHT_BASE 0x7A000000 /* CoreSight */
+#define CNS3XXX_CORESIGHT_BASE_VIRT 0xFFF0E000
+
+#define CNS3XXX_CRYPTO_BASE 0x7B000000 /* Crypto */
+#define CNS3XXX_CRYPTO_BASE_VIRT 0xFFF0F000
+
+#define CNS3XXX_I2S_BASE 0x7C000000 /* I2S */
+#define CNS3XXX_I2S_BASE_VIRT 0xFFF10000
+
+#define CNS3XXX_TIMER1_2_3_BASE 0x7C800000 /* Timer */
+#define CNS3XXX_TIMER1_2_3_BASE_VIRT 0xFFF10800
+
+#define TIMER1_COUNTER_OFFSET 0x00
+#define TIMER1_AUTO_RELOAD_OFFSET 0x04
+#define TIMER1_MATCH_V1_OFFSET 0x08
+#define TIMER1_MATCH_V2_OFFSET 0x0C
+
+#define TIMER2_COUNTER_OFFSET 0x10
+#define TIMER2_AUTO_RELOAD_OFFSET 0x14
+#define TIMER2_MATCH_V1_OFFSET 0x18
+#define TIMER2_MATCH_V2_OFFSET 0x1C
+
+#define TIMER1_2_CONTROL_OFFSET 0x30
+#define TIMER1_2_INTERRUPT_STATUS_OFFSET 0x34
+#define TIMER1_2_INTERRUPT_MASK_OFFSET 0x38
+
+#define TIMER_FREERUN_OFFSET 0x40
+#define TIMER_FREERUN_CONTROL_OFFSET 0x44
+
+#define CNS3XXX_HCIE_BASE 0x7D000000 /* HCIE Control */
+#define CNS3XXX_HCIE_BASE_VIRT 0xFFF30000
+
+#define CNS3XXX_RAID_BASE 0x7E000000 /* RAID Control */
+#define CNS3XXX_RAID_BASE_VIRT 0xFFF12000
+
+#define CNS3XXX_AXI_IXC_BASE 0x7F000000 /* AXI IXC */
+#define CNS3XXX_AXI_IXC_BASE_VIRT 0xFFF13000
+
+#define CNS3XXX_CLCD_BASE 0x80000000 /* LCD Control */
+#define CNS3XXX_CLCD_BASE_VIRT 0xFFF14000
+
+#define CNS3XXX_USBOTG_BASE 0x81000000 /* USB OTG Control */
+#define CNS3XXX_USBOTG_BASE_VIRT 0xFFF15000
+
+#define CNS3XXX_USB_BASE 0x82000000 /* USB Host Control */
+#define CNS3XXX_USB_BASE_VIRT 0xFFF16000
+
+#define CNS3XXX_SATA2_BASE 0x83000000 /* SATA */
+#define CNS3XXX_SATA2_SIZE SZ_16M
+#define CNS3XXX_SATA2_BASE_VIRT 0xFFF17000
+
+#define CNS3XXX_CAMERA_BASE 0x84000000 /* Camera Interface */
+#define CNS3XXX_CAMERA_BASE_VIRT 0xFFF18000
+
+#define CNS3XXX_SDIO_BASE 0x85000000 /* SDIO */
+#define CNS3XXX_SDIO_BASE_VIRT 0xFFF19000
+
+#define CNS3XXX_I2S_TDM_BASE 0x86000000 /* I2S TDM */
+#define CNS3XXX_I2S_TDM_BASE_VIRT 0xFFF1A000
+
+#define CNS3XXX_2DG_BASE 0x87000000 /* 2D Graphic Control */
+#define CNS3XXX_2DG_BASE_VIRT 0xFFF1B000
+
+#define CNS3XXX_USB_OHCI_BASE 0x88000000 /* USB OHCI */
+#define CNS3XXX_USB_OHCI_BASE_VIRT 0xFFF1C000
+
+#define CNS3XXX_L2C_BASE 0x92000000 /* L2 Cache Control */
+#define CNS3XXX_L2C_BASE_VIRT 0xFFF27000
+
+#define CNS3XXX_PCIE0_MEM_BASE 0xA0000000 /* PCIe Port 0 IO/Memory Space */
+#define CNS3XXX_PCIE0_MEM_BASE_VIRT 0xE0000000
+
+#define CNS3XXX_PCIE0_HOST_BASE 0xAB000000 /* PCIe Port 0 RC Base */
+#define CNS3XXX_PCIE0_HOST_BASE_VIRT 0xE1000000
+
+#define CNS3XXX_PCIE0_IO_BASE 0xAC000000 /* PCIe Port 0 */
+#define CNS3XXX_PCIE0_IO_BASE_VIRT 0xE2000000
+
+#define CNS3XXX_PCIE0_CFG0_BASE 0xAD000000 /* PCIe Port 0 CFG Type 0 */
+#define CNS3XXX_PCIE0_CFG0_BASE_VIRT 0xE3000000
+
+#define CNS3XXX_PCIE0_CFG1_BASE 0xAE000000 /* PCIe Port 0 CFG Type 1 */
+#define CNS3XXX_PCIE0_CFG1_BASE_VIRT 0xE4000000
+
+#define CNS3XXX_PCIE0_MSG_BASE 0xAF000000 /* PCIe Port 0 Message Space */
+#define CNS3XXX_PCIE0_MSG_BASE_VIRT 0xE5000000
+
+#define CNS3XXX_PCIE1_MEM_BASE 0xB0000000 /* PCIe Port 1 IO/Memory Space */
+#define CNS3XXX_PCIE1_MEM_BASE_VIRT 0xE8000000
+
+#define CNS3XXX_PCIE1_HOST_BASE 0xBB000000 /* PCIe Port 1 RC Base */
+#define CNS3XXX_PCIE1_HOST_BASE_VIRT 0xE9000000
+
+#define CNS3XXX_PCIE1_IO_BASE 0xBC000000 /* PCIe Port 1 */
+#define CNS3XXX_PCIE1_IO_BASE_VIRT 0xEA000000
+
+#define CNS3XXX_PCIE1_CFG0_BASE 0xBD000000 /* PCIe Port 1 CFG Type 0 */
+#define CNS3XXX_PCIE1_CFG0_BASE_VIRT 0xEB000000
+
+#define CNS3XXX_PCIE1_CFG1_BASE 0xBE000000 /* PCIe Port 1 CFG Type 1 */
+#define CNS3XXX_PCIE1_CFG1_BASE_VIRT 0xEC000000
+
+#define CNS3XXX_PCIE1_MSG_BASE 0xBF000000 /* PCIe Port 1 Message Space */
+#define CNS3XXX_PCIE1_MSG_BASE_VIRT 0xED000000
+
+/*
+ * Testchip peripheral and fpga gic regions
+ */
+#define CNS3XXX_TC11MP_SCU_BASE 0x90000000 /* IRQ, Test chip */
+#define CNS3XXX_TC11MP_SCU_BASE_VIRT 0xFF000000
+
+#define CNS3XXX_TC11MP_GIC_CPU_BASE 0x90000100 /* Test chip interrupt controller CPU interface */
+#define CNS3XXX_TC11MP_GIC_CPU_BASE_VIRT 0xFF000100
+
+#define CNS3XXX_TC11MP_TWD_BASE 0x90000600
+#define CNS3XXX_TC11MP_TWD_BASE_VIRT 0xFF000600
+
+#define CNS3XXX_TC11MP_GIC_DIST_BASE 0x90001000 /* Test chip interrupt controller distributor */
+#define CNS3XXX_TC11MP_GIC_DIST_BASE_VIRT 0xFF001000
+
+#define CNS3XXX_TC11MP_L220_BASE 0x92002000 /* L220 registers */
+#define CNS3XXX_TC11MP_L220_BASE_VIRT 0xFF002000
+
+/*
+ * Misc block
+ */
+#define MISC_MEM_MAP_VALUE(offset) (*((volatile unsigned int *)(CNS3XXX_MISC_BASE_VIRT + offset)))
+
+#define MISC_MEMORY_REMAP_REG MISC_MEM_MAP_VALUE(0x00)
+#define MISC_CHIP_CONFIG_REG MISC_MEM_MAP_VALUE(0x04)
+#define MISC_DEBUG_PROBE_DATA_REG MISC_MEM_MAP_VALUE(0x08)
+#define MISC_DEBUG_PROBE_SELECTION_REG MISC_MEM_MAP_VALUE(0x0C)
+#define MISC_IO_PIN_FUNC_SELECTION_REG MISC_MEM_MAP_VALUE(0x10)
+#define MISC_GPIOA_PIN_ENABLE_REG MISC_MEM_MAP_VALUE(0x14)
+#define MISC_GPIOB_PIN_ENABLE_REG MISC_MEM_MAP_VALUE(0x18)
+#define MISC_IO_PAD_DRIVE_STRENGTH_CTRL_A MISC_MEM_MAP_VALUE(0x1C)
+#define MISC_IO_PAD_DRIVE_STRENGTH_CTRL_B MISC_MEM_MAP_VALUE(0x20)
+#define MISC_GPIOA_15_0_PULL_CTRL_REG MISC_MEM_MAP_VALUE(0x24)
+#define MISC_GPIOA_16_31_PULL_CTRL_REG MISC_MEM_MAP_VALUE(0x28)
+#define MISC_GPIOB_15_0_PULL_CTRL_REG MISC_MEM_MAP_VALUE(0x2C)
+#define MISC_GPIOB_16_31_PULL_CTRL_REG MISC_MEM_MAP_VALUE(0x30)
+#define MISC_IO_PULL_CTRL_REG MISC_MEM_MAP_VALUE(0x34)
+#define MISC_E_FUSE_31_0_REG MISC_MEM_MAP_VALUE(0x40)
+#define MISC_E_FUSE_63_32_REG MISC_MEM_MAP_VALUE(0x44)
+#define MISC_E_FUSE_95_64_REG MISC_MEM_MAP_VALUE(0x48)
+#define MISC_E_FUSE_127_96_REG MISC_MEM_MAP_VALUE(0x4C)
+#define MISC_SOFTWARE_TEST_1_REG MISC_MEM_MAP_VALUE(0x50)
+#define MISC_SOFTWARE_TEST_2_REG MISC_MEM_MAP_VALUE(0x54)
+
+#define MISC_SATA_POWER_MODE MISC_MEM_MAP_VALUE(0x310)
+
+#define MISC_USB_CFG_REG MISC_MEM_MAP_VALUE(0x800)
+#define MISC_USB_STS_REG MISC_MEM_MAP_VALUE(0x804)
+#define MISC_USBPHY00_CFG_REG MISC_MEM_MAP_VALUE(0x808)
+#define MISC_USBPHY01_CFG_REG MISC_MEM_MAP_VALUE(0x80c)
+#define MISC_USBPHY10_CFG_REG MISC_MEM_MAP_VALUE(0x810)
+#define MISC_USBPHY11_CFG_REG MISC_MEM_MAP_VALUE(0x814)
+
+#define MISC_PCIEPHY_CMCTL0_REG MISC_MEM_MAP_VALUE(0x900)
+#define MISC_PCIEPHY_CMCTL1_REG MISC_MEM_MAP_VALUE(0x904)
+
+#define MISC_PCIEPHY0_CTL_REG MISC_MEM_MAP_VALUE(0x940)
+#define MISC_PCIE0_AXIS_AWMISC_REG MISC_MEM_MAP_VALUE(0x944)
+#define MISC_PCIE0_AXIS_ARMISC_REG MISC_MEM_MAP_VALUE(0x948)
+#define MISC_PCIE0_AXIS_RMISC_REG MISC_MEM_MAP_VALUE(0x94C)
+#define MISC_PCIE0_AXIS_BMISC_REG MISC_MEM_MAP_VALUE(0x950)
+#define MISC_PCIE0_AXIM_RMISC_REG MISC_MEM_MAP_VALUE(0x954)
+#define MISC_PCIE0_AXIM_BMISC_REG MISC_MEM_MAP_VALUE(0x958)
+#define MISC_PCIE0_CTRL_REG MISC_MEM_MAP_VALUE(0x95C)
+#define MISC_PCIE0_PM_DEBUG_REG MISC_MEM_MAP_VALUE(0x960)
+#define MISC_PCIE0_RFC_DEBUG_REG MISC_MEM_MAP_VALUE(0x964)
+#define MISC_PCIE0_CXPL_DEBUGL_REG MISC_MEM_MAP_VALUE(0x968)
+#define MISC_PCIE0_CXPL_DEBUGH_REG MISC_MEM_MAP_VALUE(0x96C)
+#define MISC_PCIE0_DIAG_DEBUGH_REG MISC_MEM_MAP_VALUE(0x970)
+#define MISC_PCIE0_W1CLR_REG MISC_MEM_MAP_VALUE(0x974)
+#define MISC_PCIE0_INT_MASK_REG MISC_MEM_MAP_VALUE(0x978)
+#define MISC_PCIE0_INT_STATUS_REG MISC_MEM_MAP_VALUE(0x97C)
+
+#define MISC_PCIEPHY1_CTL_REG MISC_MEM_MAP_VALUE(0xa40)
+#define MISC_PCIE1_AXIS_AWMISC_REG MISC_MEM_MAP_VALUE(0xa44)
+#define MISC_PCIE1_AXIS_ARMISC_REG MISC_MEM_MAP_VALUE(0xa48)
+#define MISC_PCIE1_AXIS_RMISC_REG MISC_MEM_MAP_VALUE(0xa4C)
+#define MISC_PCIE1_AXIS_BMISC_REG MISC_MEM_MAP_VALUE(0xa50)
+#define MISC_PCIE1_AXIM_RMISC_REG MISC_MEM_MAP_VALUE(0xa54)
+#define MISC_PCIE1_AXIM_BMISC_REG MISC_MEM_MAP_VALUE(0xa58)
+#define MISC_PCIE1_CTRL_REG MISC_MEM_MAP_VALUE(0xa5C)
+#define MISC_PCIE1_PM_DEBUG_REG MISC_MEM_MAP_VALUE(0xa60)
+#define MISC_PCIE1_RFC_DEBUG_REG MISC_MEM_MAP_VALUE(0xa64)
+#define MISC_PCIE1_CXPL_DEBUGL_REG MISC_MEM_MAP_VALUE(0xa68)
+#define MISC_PCIE1_CXPL_DEBUGH_REG MISC_MEM_MAP_VALUE(0xa6C)
+#define MISC_PCIE1_DIAG_DEBUGH_REG MISC_MEM_MAP_VALUE(0xa70)
+#define MISC_PCIE1_W1CLR_REG MISC_MEM_MAP_VALUE(0xa74)
+#define MISC_PCIE1_INT_MASK_REG MISC_MEM_MAP_VALUE(0xa78)
+#define MISC_PCIE1_INT_STATUS_REG MISC_MEM_MAP_VALUE(0xa7C)
+
+/*
+ * Power management and clock control
+ */
+#define PMU_REG_VALUE(offset) (*((volatile unsigned int *)(CNS3XXX_PM_BASE_VIRT + offset)))
+
+#define PM_CLK_GATE_REG PMU_REG_VALUE(0x000)
+#define PM_SOFT_RST_REG PMU_REG_VALUE(0x004)
+#define PM_HS_CFG_REG PMU_REG_VALUE(0x008)
+#define PM_CACTIVE_STA_REG PMU_REG_VALUE(0x00C)
+#define PM_PWR_STA_REG PMU_REG_VALUE(0x010)
+#define PM_CLK_CTRL_REG PMU_REG_VALUE(0x014)
+#define PM_PLL_LCD_I2S_CTRL_REG PMU_REG_VALUE(0x018)
+#define PM_PLL_HM_PD_CTRL_REG PMU_REG_VALUE(0x01C)
+#define PM_REGULAT_CTRL_REG PMU_REG_VALUE(0x020)
+#define PM_WDT_CTRL_REG PMU_REG_VALUE(0x024)
+#define PM_WU_CTRL0_REG PMU_REG_VALUE(0x028)
+#define PM_WU_CTRL1_REG PMU_REG_VALUE(0x02C)
+#define PM_CSR_REG PMU_REG_VALUE(0x030)
+
+/* PM_CLK_GATE_REG */
+#define PM_CLK_GATE_REG_OFFSET_SDIO (25)
+#define PM_CLK_GATE_REG_OFFSET_GPU (24)
+#define PM_CLK_GATE_REG_OFFSET_CIM (23)
+#define PM_CLK_GATE_REG_OFFSET_LCDC (22)
+#define PM_CLK_GATE_REG_OFFSET_I2S (21)
+#define PM_CLK_GATE_REG_OFFSET_RAID (20)
+#define PM_CLK_GATE_REG_OFFSET_SATA (19)
+#define PM_CLK_GATE_REG_OFFSET_PCIE0 (17)
+#define PM_CLK_GATE_REG_OFFSET_PCIE1 (18)
+#define PM_CLK_GATE_REG_OFFSET_USB_HOST (16)
+#define PM_CLK_GATE_REG_OFFSET_USB_OTG (15)
+#define PM_CLK_GATE_REG_OFFSET_TIMER (14)
+#define PM_CLK_GATE_REG_OFFSET_CRYPTO (13)
+#define PM_CLK_GATE_REG_OFFSET_HCIE (12)
+#define PM_CLK_GATE_REG_OFFSET_SWITCH (11)
+#define PM_CLK_GATE_REG_OFFSET_GPIO (10)
+#define PM_CLK_GATE_REG_OFFSET_UART3 (9)
+#define PM_CLK_GATE_REG_OFFSET_UART2 (8)
+#define PM_CLK_GATE_REG_OFFSET_UART1 (7)
+#define PM_CLK_GATE_REG_OFFSET_RTC (5)
+#define PM_CLK_GATE_REG_OFFSET_GDMA (4)
+#define PM_CLK_GATE_REG_OFFSET_SPI_PCM_I2C (3)
+#define PM_CLK_GATE_REG_OFFSET_SMC_NFI (1)
+#define PM_CLK_GATE_REG_MASK (0x03FFFFBA)
+
+/* PM_SOFT_RST_REG */
+#define PM_SOFT_RST_REG_OFFST_WARM_RST_FLAG (31)
+#define PM_SOFT_RST_REG_OFFST_CPU1 (29)
+#define PM_SOFT_RST_REG_OFFST_CPU0 (28)
+#define PM_SOFT_RST_REG_OFFST_SDIO (25)
+#define PM_SOFT_RST_REG_OFFST_GPU (24)
+#define PM_SOFT_RST_REG_OFFST_CIM (23)
+#define PM_SOFT_RST_REG_OFFST_LCDC (22)
+#define PM_SOFT_RST_REG_OFFST_I2S (21)
+#define PM_SOFT_RST_REG_OFFST_RAID (20)
+#define PM_SOFT_RST_REG_OFFST_SATA (19)
+#define PM_SOFT_RST_REG_OFFST_PCIE1 (18)
+#define PM_SOFT_RST_REG_OFFST_PCIE0 (17)
+#define PM_SOFT_RST_REG_OFFST_USB_HOST (16)
+#define PM_SOFT_RST_REG_OFFST_USB_OTG (15)
+#define PM_SOFT_RST_REG_OFFST_TIMER (14)
+#define PM_SOFT_RST_REG_OFFST_CRYPTO (13)
+#define PM_SOFT_RST_REG_OFFST_HCIE (12)
+#define PM_SOFT_RST_REG_OFFST_SWITCH (11)
+#define PM_SOFT_RST_REG_OFFST_GPIO (10)
+#define PM_SOFT_RST_REG_OFFST_UART3 (9)
+#define PM_SOFT_RST_REG_OFFST_UART2 (8)
+#define PM_SOFT_RST_REG_OFFST_UART1 (7)
+#define PM_SOFT_RST_REG_OFFST_RTC (5)
+#define PM_SOFT_RST_REG_OFFST_GDMA (4)
+#define PM_SOFT_RST_REG_OFFST_SPI_PCM_I2C (3)
+#define PM_SOFT_RST_REG_OFFST_DMC (2)
+#define PM_SOFT_RST_REG_OFFST_SMC_NFI (1)
+#define PM_SOFT_RST_REG_OFFST_GLOBAL (0)
+#define PM_SOFT_RST_REG_MASK (0xF3FFFFBF)
+
+/* PMHS_CFG_REG */
+#define PM_HS_CFG_REG_OFFSET_SDIO (25)
+#define PM_HS_CFG_REG_OFFSET_GPU (24)
+#define PM_HS_CFG_REG_OFFSET_CIM (23)
+#define PM_HS_CFG_REG_OFFSET_LCDC (22)
+#define PM_HS_CFG_REG_OFFSET_I2S (21)
+#define PM_HS_CFG_REG_OFFSET_RAID (20)
+#define PM_HS_CFG_REG_OFFSET_SATA (19)
+#define PM_HS_CFG_REG_OFFSET_PCIE1 (18)
+#define PM_HS_CFG_REG_OFFSET_PCIE0 (17)
+#define PM_HS_CFG_REG_OFFSET_USB_HOST (16)
+#define PM_HS_CFG_REG_OFFSET_USB_OTG (15)
+#define PM_HS_CFG_REG_OFFSET_TIMER (14)
+#define PM_HS_CFG_REG_OFFSET_CRYPTO (13)
+#define PM_HS_CFG_REG_OFFSET_HCIE (12)
+#define PM_HS_CFG_REG_OFFSET_SWITCH (11)
+#define PM_HS_CFG_REG_OFFSET_GPIO (10)
+#define PM_HS_CFG_REG_OFFSET_UART3 (9)
+#define PM_HS_CFG_REG_OFFSET_UART2 (8)
+#define PM_HS_CFG_REG_OFFSET_UART1 (7)
+#define PM_HS_CFG_REG_OFFSET_RTC (5)
+#define PM_HS_CFG_REG_OFFSET_GDMA (4)
+#define PM_HS_CFG_REG_OFFSET_SPI_PCM_I2S (3)
+#define PM_HS_CFG_REG_OFFSET_DMC (2)
+#define PM_HS_CFG_REG_OFFSET_SMC_NFI (1)
+#define PM_HS_CFG_REG_MASK (0x03FFFFBE)
+#define PM_HS_CFG_REG_MASK_SUPPORT (0x01100806)
+
+/* PM_CACTIVE_STA_REG */
+#define PM_CACTIVE_STA_REG_OFFSET_SDIO (25)
+#define PM_CACTIVE_STA_REG_OFFSET_GPU (24)
+#define PM_CACTIVE_STA_REG_OFFSET_CIM (23)
+#define PM_CACTIVE_STA_REG_OFFSET_LCDC (22)
+#define PM_CACTIVE_STA_REG_OFFSET_I2S (21)
+#define PM_CACTIVE_STA_REG_OFFSET_RAID (20)
+#define PM_CACTIVE_STA_REG_OFFSET_SATA (19)
+#define PM_CACTIVE_STA_REG_OFFSET_PCIE1 (18)
+#define PM_CACTIVE_STA_REG_OFFSET_PCIE0 (17)
+#define PM_CACTIVE_STA_REG_OFFSET_USB_HOST (16)
+#define PM_CACTIVE_STA_REG_OFFSET_USB_OTG (15)
+#define PM_CACTIVE_STA_REG_OFFSET_TIMER (14)
+#define PM_CACTIVE_STA_REG_OFFSET_CRYPTO (13)
+#define PM_CACTIVE_STA_REG_OFFSET_HCIE (12)
+#define PM_CACTIVE_STA_REG_OFFSET_SWITCH (11)
+#define PM_CACTIVE_STA_REG_OFFSET_GPIO (10)
+#define PM_CACTIVE_STA_REG_OFFSET_UART3 (9)
+#define PM_CACTIVE_STA_REG_OFFSET_UART2 (8)
+#define PM_CACTIVE_STA_REG_OFFSET_UART1 (7)
+#define PM_CACTIVE_STA_REG_OFFSET_RTC (5)
+#define PM_CACTIVE_STA_REG_OFFSET_GDMA (4)
+#define PM_CACTIVE_STA_REG_OFFSET_SPI_PCM_I2S (3)
+#define PM_CACTIVE_STA_REG_OFFSET_DMC (2)
+#define PM_CACTIVE_STA_REG_OFFSET_SMC_NFI (1)
+#define PM_CACTIVE_STA_REG_MASK (0x03FFFFBE)
+
+/* PM_PWR_STA_REG */
+#define PM_PWR_STA_REG_REG_OFFSET_SDIO (25)
+#define PM_PWR_STA_REG_REG_OFFSET_GPU (24)
+#define PM_PWR_STA_REG_REG_OFFSET_CIM (23)
+#define PM_PWR_STA_REG_REG_OFFSET_LCDC (22)
+#define PM_PWR_STA_REG_REG_OFFSET_I2S (21)
+#define PM_PWR_STA_REG_REG_OFFSET_RAID (20)
+#define PM_PWR_STA_REG_REG_OFFSET_SATA (19)
+#define PM_PWR_STA_REG_REG_OFFSET_PCIE1 (18)
+#define PM_PWR_STA_REG_REG_OFFSET_PCIE0 (17)
+#define PM_PWR_STA_REG_REG_OFFSET_USB_HOST (16)
+#define PM_PWR_STA_REG_REG_OFFSET_USB_OTG (15)
+#define PM_PWR_STA_REG_REG_OFFSET_TIMER (14)
+#define PM_PWR_STA_REG_REG_OFFSET_CRYPTO (13)
+#define PM_PWR_STA_REG_REG_OFFSET_HCIE (12)
+#define PM_PWR_STA_REG_REG_OFFSET_SWITCH (11)
+#define PM_PWR_STA_REG_REG_OFFSET_GPIO (10)
+#define PM_PWR_STA_REG_REG_OFFSET_UART3 (9)
+#define PM_PWR_STA_REG_REG_OFFSET_UART2 (8)
+#define PM_PWR_STA_REG_REG_OFFSET_UART1 (7)
+#define PM_PWR_STA_REG_REG_OFFSET_RTC (5)
+#define PM_PWR_STA_REG_REG_OFFSET_GDMA (4)
+#define PM_PWR_STA_REG_REG_OFFSET_SPI_PCM_I2S (3)
+#define PM_PWR_STA_REG_REG_OFFSET_DMC (2)
+#define PM_PWR_STA_REG_REG_OFFSET_SMC_NFI (1)
+#define PM_PWR_STA_REG_REG_MASK (0x03FFFFBE)
+
+/* PM_CLK_CTRL_REG */
+#define PM_CLK_CTRL_REG_OFFSET_I2S_MCLK (31)
+#define PM_CLK_CTRL_REG_OFFSET_DDR2_CHG_EN (30)
+#define PM_CLK_CTRL_REG_OFFSET_PCIE_REF1_EN (29)
+#define PM_CLK_CTRL_REG_OFFSET_PCIE_REF0_EN (28)
+#define PM_CLK_CTRL_REG_OFFSET_TIMER_SIM_MODE (27)
+#define PM_CLK_CTRL_REG_OFFSET_I2SCLK_DIV (24)
+#define PM_CLK_CTRL_REG_OFFSET_I2SCLK_SEL (22)
+#define PM_CLK_CTRL_REG_OFFSET_CLKOUT_DIV (20)
+#define PM_CLK_CTRL_REG_OFFSET_CLKOUT_SEL (16)
+#define PM_CLK_CTRL_REG_OFFSET_MDC_DIV (14)
+#define PM_CLK_CTRL_REG_OFFSET_CRYPTO_CLK_SEL (12)
+#define PM_CLK_CTRL_REG_OFFSET_CPU_PWR_MODE (9)
+#define PM_CLK_CTRL_REG_OFFSET_PLL_DDR2_SEL (7)
+#define PM_CLK_CTRL_REG_OFFSET_DIV_IMMEDIATE (6)
+#define PM_CLK_CTRL_REG_OFFSET_CPU_CLK_DIV (4)
+#define PM_CLK_CTRL_REG_OFFSET_PLL_CPU_SEL (0)
+
+#define PM_CPU_CLK_DIV(DIV) { \
+ PM_CLK_CTRL_REG &= ~((0x3) << PM_CLK_CTRL_REG_OFFSET_CPU_CLK_DIV); \
+ PM_CLK_CTRL_REG |= (((DIV)&0x3) << PM_CLK_CTRL_REG_OFFSET_CPU_CLK_DIV); \
+}
+
+#define PM_PLL_CPU_SEL(CPU) { \
+ PM_CLK_CTRL_REG &= ~((0xF) << PM_CLK_CTRL_REG_OFFSET_PLL_CPU_SEL); \
+ PM_CLK_CTRL_REG |= (((CPU)&0xF) << PM_CLK_CTRL_REG_OFFSET_PLL_CPU_SEL); \
+}
+
+/* PM_PLL_LCD_I2S_CTRL_REG */
+#define PM_PLL_LCD_I2S_CTRL_REG_OFFSET_MCLK_SMC_DIV (22)
+#define PM_PLL_LCD_I2S_CTRL_REG_OFFSET_R_SEL (17)
+#define PM_PLL_LCD_I2S_CTRL_REG_OFFSET_PLL_LCD_P (11)
+#define PM_PLL_LCD_I2S_CTRL_REG_OFFSET_PLL_LCD_M (3)
+#define PM_PLL_LCD_I2S_CTRL_REG_OFFSET_PLL_LCD_S (0)
+
+/* PM_PLL_HM_PD_CTRL_REG */
+#define PM_PLL_HM_PD_CTRL_REG_OFFSET_SATA_PHY1 (11)
+#define PM_PLL_HM_PD_CTRL_REG_OFFSET_SATA_PHY0 (10)
+#define PM_PLL_HM_PD_CTRL_REG_OFFSET_PLL_I2SCD (6)
+#define PM_PLL_HM_PD_CTRL_REG_OFFSET_PLL_I2S (5)
+#define PM_PLL_HM_PD_CTRL_REG_OFFSET_PLL_LCD (4)
+#define PM_PLL_HM_PD_CTRL_REG_OFFSET_PLL_USB (3)
+#define PM_PLL_HM_PD_CTRL_REG_OFFSET_PLL_RGMII (2)
+#define PM_PLL_HM_PD_CTRL_REG_MASK (0x00000C7C)
+
+/* PM_WDT_CTRL_REG */
+#define PM_WDT_CTRL_REG_OFFSET_RESET_CPU_ONLY (0)
+
+/* PM_CSR_REG - Clock Scaling Register*/
+#define PM_CSR_REG_OFFSET_CSR_EN (30)
+#define PM_CSR_REG_OFFSET_CSR_NUM (0)
+
+#define CNS3XXX_PWR_CLK_EN(BLOCK) (0x1<<PM_CLK_GATE_REG_OFFSET_##BLOCK)
+
+/* Software reset*/
+#define CNS3XXX_PWR_SOFTWARE_RST(BLOCK) (0x1<<PM_SOFT_RST_REG_OFFST_##BLOCK)
+
+/*
+ * CNS3XXX support several power saving mode as following,
+ * DFS, IDLE, HALT, DOZE, SLEEP, Hibernate
+ */
+#define CNS3XXX_PWR_CPU_MODE_DFS (0)
+#define CNS3XXX_PWR_CPU_MODE_IDLE (1)
+#define CNS3XXX_PWR_CPU_MODE_HALT (2)
+#define CNS3XXX_PWR_CPU_MODE_DOZE (3)
+#define CNS3XXX_PWR_CPU_MODE_SLEEP (4)
+#define CNS3XXX_PWR_CPU_MODE_HIBERNATE (5)
+
+#define CNS3XXX_PWR_PLL(BLOCK) (0x1<<PM_PLL_HM_PD_CTRL_REG_OFFSET_##BLOCK)
+#define CNS3XXX_PWR_PLL_ALL PM_PLL_HM_PD_CTRL_REG_MASK
+
+/* Change CPU frequency and divider */
+#define CNS3XXX_PWR_PLL_CPU_300MHZ (0)
+#define CNS3XXX_PWR_PLL_CPU_333MHZ (1)
+#define CNS3XXX_PWR_PLL_CPU_366MHZ (2)
+#define CNS3XXX_PWR_PLL_CPU_400MHZ (3)
+#define CNS3XXX_PWR_PLL_CPU_433MHZ (4)
+#define CNS3XXX_PWR_PLL_CPU_466MHZ (5)
+#define CNS3XXX_PWR_PLL_CPU_500MHZ (6)
+#define CNS3XXX_PWR_PLL_CPU_533MHZ (7)
+#define CNS3XXX_PWR_PLL_CPU_566MHZ (8)
+#define CNS3XXX_PWR_PLL_CPU_600MHZ (9)
+#define CNS3XXX_PWR_PLL_CPU_633MHZ (10)
+#define CNS3XXX_PWR_PLL_CPU_666MHZ (11)
+#define CNS3XXX_PWR_PLL_CPU_700MHZ (12)
+
+#define CNS3XXX_PWR_CPU_CLK_DIV_BY1 (0)
+#define CNS3XXX_PWR_CPU_CLK_DIV_BY2 (1)
+#define CNS3XXX_PWR_CPU_CLK_DIV_BY4 (2)
+
+/* Change DDR2 frequency */
+#define CNS3XXX_PWR_PLL_DDR2_200MHZ (0)
+#define CNS3XXX_PWR_PLL_DDR2_266MHZ (1)
+#define CNS3XXX_PWR_PLL_DDR2_333MHZ (2)
+#define CNS3XXX_PWR_PLL_DDR2_400MHZ (3)
+
+void cns3xxx_pwr_soft_rst(unsigned int block);
+void cns3xxx_pwr_clk_en(unsigned int block);
+int cns3xxx_cpu_clock(void);
+
+/*
+ * ARM11 MPCore interrupt sources (primary GIC)
+ */
+#define IRQ_CNS3XXX_PMU (IRQ_TC11MP_GIC_START + 0)
+#define IRQ_CNS3XXX_SDIO (IRQ_TC11MP_GIC_START + 1)
+#define IRQ_CNS3XXX_L2CC (IRQ_TC11MP_GIC_START + 2)
+#define IRQ_CNS3XXX_RTC (IRQ_TC11MP_GIC_START + 3)
+#define IRQ_CNS3XXX_I2S (IRQ_TC11MP_GIC_START + 4)
+#define IRQ_CNS3XXX_PCM (IRQ_TC11MP_GIC_START + 5)
+#define IRQ_CNS3XXX_SPI (IRQ_TC11MP_GIC_START + 6)
+#define IRQ_CNS3XXX_I2C (IRQ_TC11MP_GIC_START + 7)
+#define IRQ_CNS3XXX_CIM (IRQ_TC11MP_GIC_START + 8)
+#define IRQ_CNS3XXX_GPU (IRQ_TC11MP_GIC_START + 9)
+#define IRQ_CNS3XXX_LCD (IRQ_TC11MP_GIC_START + 10)
+#define IRQ_CNS3XXX_GPIOA (IRQ_TC11MP_GIC_START + 11)
+#define IRQ_CNS3XXX_GPIOB (IRQ_TC11MP_GIC_START + 12)
+#define IRQ_CNS3XXX_UART0 (IRQ_TC11MP_GIC_START + 13)
+#define IRQ_CNS3XXX_UART1 (IRQ_TC11MP_GIC_START + 14)
+#define IRQ_CNS3XXX_UART2 (IRQ_TC11MP_GIC_START + 15)
+#define IRQ_CNS3XXX_ARM11 (IRQ_TC11MP_GIC_START + 16)
+
+#define IRQ_CNS3XXX_SW_STATUS (IRQ_TC11MP_GIC_START + 17)
+#define IRQ_CNS3XXX_SW_R0TXC (IRQ_TC11MP_GIC_START + 18)
+#define IRQ_CNS3XXX_SW_R0RXC (IRQ_TC11MP_GIC_START + 19)
+#define IRQ_CNS3XXX_SW_R0QE (IRQ_TC11MP_GIC_START + 20)
+#define IRQ_CNS3XXX_SW_R0QF (IRQ_TC11MP_GIC_START + 21)
+#define IRQ_CNS3XXX_SW_R1TXC (IRQ_TC11MP_GIC_START + 22)
+#define IRQ_CNS3XXX_SW_R1RXC (IRQ_TC11MP_GIC_START + 23)
+#define IRQ_CNS3XXX_SW_R1QE (IRQ_TC11MP_GIC_START + 24)
+#define IRQ_CNS3XXX_SW_R1QF (IRQ_TC11MP_GIC_START + 25)
+#define IRQ_CNS3XXX_SW_PPE (IRQ_TC11MP_GIC_START + 26)
+
+#define IRQ_CNS3XXX_CRYPTO (IRQ_TC11MP_GIC_START + 27)
+#define IRQ_CNS3XXX_HCIE (IRQ_TC11MP_GIC_START + 28)
+#define IRQ_CNS3XXX_PCIE0_DEVICE (IRQ_TC11MP_GIC_START + 29)
+#define IRQ_CNS3XXX_PCIE1_DEVICE (IRQ_TC11MP_GIC_START + 30)
+#define IRQ_CNS3XXX_USB_OTG (IRQ_TC11MP_GIC_START + 31)
+#define IRQ_CNS3XXX_USB_EHCI (IRQ_TC11MP_GIC_START + 32)
+#define IRQ_CNS3XXX_SATA (IRQ_TC11MP_GIC_START + 33)
+#define IRQ_CNS3XXX_RAID (IRQ_TC11MP_GIC_START + 34)
+#define IRQ_CNS3XXX_SMC (IRQ_TC11MP_GIC_START + 35)
+
+#define IRQ_CNS3XXX_DMAC_ABORT (IRQ_TC11MP_GIC_START + 36)
+#define IRQ_CNS3XXX_DMAC0 (IRQ_TC11MP_GIC_START + 37)
+#define IRQ_CNS3XXX_DMAC1 (IRQ_TC11MP_GIC_START + 38)
+#define IRQ_CNS3XXX_DMAC2 (IRQ_TC11MP_GIC_START + 39)
+#define IRQ_CNS3XXX_DMAC3 (IRQ_TC11MP_GIC_START + 40)
+#define IRQ_CNS3XXX_DMAC4 (IRQ_TC11MP_GIC_START + 41)
+#define IRQ_CNS3XXX_DMAC5 (IRQ_TC11MP_GIC_START + 42)
+#define IRQ_CNS3XXX_DMAC6 (IRQ_TC11MP_GIC_START + 43)
+#define IRQ_CNS3XXX_DMAC7 (IRQ_TC11MP_GIC_START + 44)
+#define IRQ_CNS3XXX_DMAC8 (IRQ_TC11MP_GIC_START + 45)
+#define IRQ_CNS3XXX_DMAC9 (IRQ_TC11MP_GIC_START + 46)
+#define IRQ_CNS3XXX_DMAC10 (IRQ_TC11MP_GIC_START + 47)
+#define IRQ_CNS3XXX_DMAC11 (IRQ_TC11MP_GIC_START + 48)
+#define IRQ_CNS3XXX_DMAC12 (IRQ_TC11MP_GIC_START + 49)
+#define IRQ_CNS3XXX_DMAC13 (IRQ_TC11MP_GIC_START + 50)
+#define IRQ_CNS3XXX_DMAC14 (IRQ_TC11MP_GIC_START + 51)
+#define IRQ_CNS3XXX_DMAC15 (IRQ_TC11MP_GIC_START + 52)
+#define IRQ_CNS3XXX_DMAC16 (IRQ_TC11MP_GIC_START + 53)
+#define IRQ_CNS3XXX_DMAC17 (IRQ_TC11MP_GIC_START + 54)
+
+#define IRQ_CNS3XXX_PCIE0_RC (IRQ_TC11MP_GIC_START + 55)
+#define IRQ_CNS3XXX_PCIE1_RC (IRQ_TC11MP_GIC_START + 56)
+#define IRQ_CNS3XXX_TIMER0 (IRQ_TC11MP_GIC_START + 57)
+#define IRQ_CNS3XXX_TIMER1 (IRQ_TC11MP_GIC_START + 58)
+#define IRQ_CNS3XXX_USB_OHCI (IRQ_TC11MP_GIC_START + 59)
+#define IRQ_CNS3XXX_TIMER2 (IRQ_TC11MP_GIC_START + 60)
+#define IRQ_CNS3XXX_EXTERNAL_PIN0 (IRQ_TC11MP_GIC_START + 61)
+#define IRQ_CNS3XXX_EXTERNAL_PIN1 (IRQ_TC11MP_GIC_START + 62)
+#define IRQ_CNS3XXX_EXTERNAL_PIN2 (IRQ_TC11MP_GIC_START + 63)
+
+#define NR_IRQS_CNS3XXX (IRQ_TC11MP_GIC_START + 64)
+
+#if !defined(NR_IRQS) || (NR_IRQS < NR_IRQS_CNS3XXX)
+#undef NR_IRQS
+#define NR_IRQS NR_IRQS_CNS3XXX
+#endif
+
+#endif /* __MACH_BOARD_CNS3XXX_H */
diff --git a/arch/arm/mach-cns3xxx/include/mach/debug-macro.S b/arch/arm/mach-cns3xxx/include/mach/debug-macro.S
new file mode 100644
index 0000000..d16ce7e
--- /dev/null
+++ b/arch/arm/mach-cns3xxx/include/mach/debug-macro.S
@@ -0,0 +1,21 @@
+/*
+ * Debugging macro include header
+ *
+ * Copyright 1994-1999 Russell King
+ * Copyright 2008 Cavium Networks
+ * Moved from linux/arch/arm/kernel/debug.S by Ben Dooks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ */
+
+ .macro addruart,rx
+ mrc p15, 0, \rx, c1, c0
+ tst \rx, #1 @ MMU enabled?
+ moveq \rx, #0x10000000
+ movne \rx, #0xf0000000 @ virtual base
+ orr \rx, \rx, #0x00009000
+ .endm
+
+#include <asm/hardware/debug-pl01x.S>
diff --git a/arch/arm/mach-cns3xxx/include/mach/entry-macro.S b/arch/arm/mach-cns3xxx/include/mach/entry-macro.S
new file mode 100644
index 0000000..5e1c554
--- /dev/null
+++ b/arch/arm/mach-cns3xxx/include/mach/entry-macro.S
@@ -0,0 +1,82 @@
+/*
+ * Low-level IRQ helper macros for Cavium Networks platforms
+ *
+ * Copyright 2008 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ */
+
+#include <mach/hardware.h>
+#include <asm/hardware/gic.h>
+
+ .macro disable_fiq
+ .endm
+
+ .macro get_irqnr_preamble, base, tmp
+ ldr \base, =gic_cpu_base_addr
+ ldr \base, [\base]
+ .endm
+
+ .macro arch_ret_to_user, tmp1, tmp2
+ .endm
+
+ /*
+ * The interrupt numbering scheme is defined in the
+ * interrupt controller spec. To wit:
+ *
+ * Interrupts 0-15 are IPI
+ * 16-28 are reserved
+ * 29-31 are local. We allow 30 to be used for the watchdog.
+ * 32-1020 are global
+ * 1021-1022 are reserved
+ * 1023 is "spurious" (no interrupt)
+ *
+ * For now, we ignore all local interrupts so only return an interrupt if it's
+ * between 30 and 1020. The test_for_ipi routine below will pick up on IPIs.
+ *
+ * A simple read from the controller will tell us the number of the highest
+ * priority enabled interrupt. We then just need to check whether it is in the
+ * valid range for an IRQ (30-1020 inclusive).
+ */
+
+ .macro get_irqnr_and_base, irqnr, irqstat, base, tmp
+
+ ldr \irqstat, [\base, #GIC_CPU_INTACK] /* bits 12-10 = src CPU, 9-0 = int # */
+
+ ldr \tmp, =1021
+
+ bic \irqnr, \irqstat, #0x1c00
+
+ cmp \irqnr, #29
+ cmpcc \irqnr, \irqnr
+ cmpne \irqnr, \tmp
+ cmpcs \irqnr, \irqnr
+
+ .endm
+
+ /* We assume that irqstat (the raw value of the IRQ acknowledge
+ * register) is preserved from the macro above.
+ * If there is an IPI, we immediately signal end of interrupt on the
+ * controller, since this requires the original irqstat value which
+ * we won't easily be able to recreate later.
+ */
+
+ .macro test_for_ipi, irqnr, irqstat, base, tmp
+ bic \irqnr, \irqstat, #0x1c00
+ cmp \irqnr, #16
+ strcc \irqstat, [\base, #GIC_CPU_EOI]
+ cmpcs \irqnr, \irqnr
+ .endm
+
+ /* As above, this assumes that irqstat and base are preserved.. */
+
+ .macro test_for_ltirq, irqnr, irqstat, base, tmp
+ bic \irqnr, \irqstat, #0x1c00
+ mov \tmp, #0
+ cmp \irqnr, #29
+ moveq \tmp, #1
+ streq \irqstat, [\base, #GIC_CPU_EOI]
+ cmp \tmp, #0
+ .endm
diff --git a/arch/arm/mach-cns3xxx/include/mach/hardware.h b/arch/arm/mach-cns3xxx/include/mach/hardware.h
new file mode 100644
index 0000000..57e0983
--- /dev/null
+++ b/arch/arm/mach-cns3xxx/include/mach/hardware.h
@@ -0,0 +1,22 @@
+/*
+ * This file contains the hardware definitions of the Cavium Networks boards.
+ *
+ * Copyright 2003 ARM Limited.
+ * Copyright 2008 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef __MACH_HARDWARE_H
+#define __MACH_HARDWARE_H
+
+#include <asm/sizes.h>
+
+/* macro to get at IO space when running virtually */
+#define PCIBIOS_MIN_IO 0x00000000
+#define PCIBIOS_MIN_MEM 0x00000000
+#define pcibios_assign_all_busses() 1
+
+#endif
diff --git a/arch/arm/mach-cns3xxx/include/mach/io.h b/arch/arm/mach-cns3xxx/include/mach/io.h
new file mode 100644
index 0000000..b4ff09a
--- /dev/null
+++ b/arch/arm/mach-cns3xxx/include/mach/io.h
@@ -0,0 +1,22 @@
+/*
+ * Copyright 2008 Cavium Networks
+ * Copyright 2003 ARM Limited
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ */
+#ifndef __MACH_IO_H
+#define __MACH_IO_H
+
+#define IO_SPACE_LIMIT 0xffffffff
+
+static inline void __iomem *__io(unsigned long addr)
+{
+ return (void __iomem *)addr;
+}
+
+#define __io(a) __typesafe_io(a)
+#define __mem_pci(a) (a)
+
+#endif
diff --git a/arch/arm/mach-cns3xxx/include/mach/irqs.h b/arch/arm/mach-cns3xxx/include/mach/irqs.h
new file mode 100644
index 0000000..2ab96f8
--- /dev/null
+++ b/arch/arm/mach-cns3xxx/include/mach/irqs.h
@@ -0,0 +1,24 @@
+/*
+ * Copyright 2000 Deep Blue Solutions Ltd.
+ * Copyright 2003 ARM Limited
+ * Copyright 2008 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef __MACH_IRQS_H
+#define __MACH_IRQS_H
+
+#define IRQ_LOCALTIMER 29
+#define IRQ_LOCALWDOG 30
+#define IRQ_TC11MP_GIC_START 32
+
+#include <mach/cns3xxx.h>
+
+#ifndef NR_IRQS
+#error "NR_IRQS not defined by the board-specific files"
+#endif
+
+#endif
diff --git a/arch/arm/mach-cns3xxx/include/mach/memory.h b/arch/arm/mach-cns3xxx/include/mach/memory.h
new file mode 100644
index 0000000..3b6b769
--- /dev/null
+++ b/arch/arm/mach-cns3xxx/include/mach/memory.h
@@ -0,0 +1,26 @@
+/*
+ * Copyright 2003 ARM Limited
+ * Copyright 2008 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef __MACH_MEMORY_H
+#define __MACH_MEMORY_H
+
+/*
+ * Physical DRAM offset.
+ */
+#define PHYS_OFFSET UL(0x00000000)
+
+#define __phys_to_bus(x) ((x) + PHYS_OFFSET)
+#define __bus_to_phys(x) ((x) - PHYS_OFFSET)
+
+#define __virt_to_bus(v) __phys_to_bus(__virt_to_phys(v))
+#define __bus_to_virt(b) __phys_to_virt(__bus_to_phys(b))
+#define __pfn_to_bus(p) __phys_to_bus(__pfn_to_phys(p))
+#define __bus_to_pfn(b) __phys_to_pfn(__bus_to_phys(b))
+
+#endif
diff --git a/arch/arm/mach-cns3xxx/include/mach/system.h b/arch/arm/mach-cns3xxx/include/mach/system.h
new file mode 100644
index 0000000..58bb03a
--- /dev/null
+++ b/arch/arm/mach-cns3xxx/include/mach/system.h
@@ -0,0 +1,29 @@
+/*
+ * Copyright 2000 Deep Blue Solutions Ltd
+ * Copyright 2003 ARM Limited
+ * Copyright 2008 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef __MACH_SYSTEM_H
+#define __MACH_SYSTEM_H
+
+#include <linux/io.h>
+#include <asm/proc-fns.h>
+#include <mach/hardware.h>
+
+static inline void arch_idle(void)
+{
+ /*
+ * This should do all the clock switching
+ * and wait for interrupt tricks
+ */
+ cpu_do_idle();
+}
+
+void arch_reset(char mode, const char *cmd);
+
+#endif
diff --git a/arch/arm/mach-cns3xxx/include/mach/timex.h b/arch/arm/mach-cns3xxx/include/mach/timex.h
new file mode 100644
index 0000000..1fd0421
--- /dev/null
+++ b/arch/arm/mach-cns3xxx/include/mach/timex.h
@@ -0,0 +1,12 @@
+/*
+ * Cavium Networks architecture timex specifications
+ *
+ * Copyright 2003 ARM Limited
+ * Copyright 2008 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ */
+
+#define CLOCK_TICK_RATE (50000000 / 16)
diff --git a/arch/arm/mach-cns3xxx/include/mach/uncompress.h b/arch/arm/mach-cns3xxx/include/mach/uncompress.h
new file mode 100644
index 0000000..de8ead9
--- /dev/null
+++ b/arch/arm/mach-cns3xxx/include/mach/uncompress.h
@@ -0,0 +1,55 @@
+/*
+ * Copyright 2003 ARM Limited
+ * Copyright 2008 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ */
+
+#include <asm/mach-types.h>
+#include <mach/hardware.h>
+#include <mach/cns3xxx.h>
+
+#define AMBA_UART_DR(base) (*(volatile unsigned char *)((base) + 0x00))
+#define AMBA_UART_LCRH(base) (*(volatile unsigned char *)((base) + 0x2c))
+#define AMBA_UART_CR(base) (*(volatile unsigned char *)((base) + 0x30))
+#define AMBA_UART_FR(base) (*(volatile unsigned char *)((base) + 0x18))
+
+/*
+ * Return the UART base address
+ */
+static inline unsigned long get_uart_base(void)
+{
+ if (machine_is_cns3420vb())
+ return CNS3XXX_UART0_BASE;
+ else
+ return 0;
+}
+
+/*
+ * This does not append a newline
+ */
+static inline void putc(int c)
+{
+ unsigned long base = get_uart_base();
+
+ while (AMBA_UART_FR(base) & (1 << 5))
+ barrier();
+
+ AMBA_UART_DR(base) = c;
+}
+
+static inline void flush(void)
+{
+ unsigned long base = get_uart_base();
+
+ while (AMBA_UART_FR(base) & (1 << 3))
+ barrier();
+}
+
+/*
+ * nothing to do
+ */
+#define arch_decomp_setup()
+#define arch_decomp_wdog()
diff --git a/arch/arm/mach-cns3xxx/include/mach/vmalloc.h b/arch/arm/mach-cns3xxx/include/mach/vmalloc.h
new file mode 100644
index 0000000..4d381ec
--- /dev/null
+++ b/arch/arm/mach-cns3xxx/include/mach/vmalloc.h
@@ -0,0 +1,11 @@
+/*
+ * Copyright 2000 Russell King.
+ * Copyright 2003 ARM Limited
+ * Copyright 2008 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ */
+
+#define VMALLOC_END 0xd8000000
diff --git a/arch/arm/mach-cns3xxx/pm.c b/arch/arm/mach-cns3xxx/pm.c
new file mode 100644
index 0000000..725e1a4
--- /dev/null
+++ b/arch/arm/mach-cns3xxx/pm.c
@@ -0,0 +1,86 @@
+/*
+ * Copyright 2008 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/delay.h>
+#include <mach/system.h>
+#include <mach/cns3xxx.h>
+
+void cns3xxx_pwr_clk_en(unsigned int block)
+{
+ PM_CLK_GATE_REG |= (block & PM_CLK_GATE_REG_MASK);
+}
+
+void cns3xxx_pwr_power_up(unsigned int block)
+{
+ PM_PLL_HM_PD_CTRL_REG &= ~(block & CNS3XXX_PWR_PLL_ALL);
+
+ /* Wait for 300us for the PLL output clock locked. */
+ udelay(300);
+};
+
+void cns3xxx_pwr_power_down(unsigned int block)
+{
+ /* write '1' to power down */
+ PM_PLL_HM_PD_CTRL_REG |= (block & CNS3XXX_PWR_PLL_ALL);
+};
+
+static void cns3xxx_pwr_soft_rst_force(unsigned int block)
+{
+ /*
+ * bit 0, 28, 29 => program low to reset,
+ * the other else program low and then high
+ */
+ if (block & 0x30000001) {
+ PM_SOFT_RST_REG &= ~(block & PM_SOFT_RST_REG_MASK);
+ } else {
+ PM_SOFT_RST_REG &= ~(block & PM_SOFT_RST_REG_MASK);
+ PM_SOFT_RST_REG |= (block & PM_SOFT_RST_REG_MASK);
+ }
+}
+
+void cns3xxx_pwr_soft_rst(unsigned int block)
+{
+ static unsigned int soft_reset;
+
+ if (soft_reset & block) {
+ /* SPI/I2C/GPIO use the same block, reset once. */
+ return;
+ } else {
+ soft_reset |= block;
+ }
+ cns3xxx_pwr_soft_rst_force(block);
+}
+
+void arch_reset(char mode, const char *cmd)
+{
+ /*
+ * To reset, we hit the on-board reset register
+ * in the system FPGA.
+ */
+ cns3xxx_pwr_soft_rst(CNS3XXX_PWR_SOFTWARE_RST(GLOBAL));
+}
+
+/*
+ * cns3xxx_cpu_clock - return CPU/L2 clock
+ * aclk: cpu clock/2
+ * hclk: cpu clock/4
+ * pclk: cpu clock/8
+ */
+int cns3xxx_cpu_clock(void)
+{
+ int cpu;
+ int cpu_sel;
+ int div_sel;
+
+ cpu_sel = (PM_CLK_CTRL_REG >> PM_CLK_CTRL_REG_OFFSET_PLL_CPU_SEL) & 0xf;
+ div_sel = (PM_CLK_CTRL_REG >> PM_CLK_CTRL_REG_OFFSET_CPU_CLK_DIV) & 0x3;
+
+ cpu = (300 + ((cpu_sel / 3) * 100) + ((cpu_sel % 3) * 33)) >> div_sel;
+
+ return cpu;
+}
--
1.7.0
^ permalink raw reply related [flat|nested] 4+ messages in thread* [PATCH 2/3] ARM: cns3xxx: Add CNS3420 Validation Board support
2010-03-26 19:23 [PATCH v2 0/3] Support for Cavium Networks CNS3xxx machines Anton Vorontsov
2010-03-26 19:23 ` [PATCH 1/3] ARM: cns3xxx: Add basic support for Cavium Networks CNS3xxx processors Anton Vorontsov
@ 2010-03-26 19:23 ` Anton Vorontsov
2010-03-26 19:23 ` [PATCH 3/3] ARM: cns3xxx: Add defconfig for CNS3420 validation board Anton Vorontsov
2 siblings, 0 replies; 4+ messages in thread
From: Anton Vorontsov @ 2010-03-26 19:23 UTC (permalink / raw)
To: linux-arm-kernel
This patch adds support for CNS3420VB rev 1.3 boards. With this patch
CNS3420VB boards are able to boot up to the userspace, with a console
available on UART0.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
---
arch/arm/mach-cns3xxx/Kconfig | 8 ++
arch/arm/mach-cns3xxx/Makefile | 1 +
arch/arm/mach-cns3xxx/cns3420vb.c | 148 +++++++++++++++++++++++++++++++++++++
3 files changed, 157 insertions(+), 0 deletions(-)
create mode 100644 arch/arm/mach-cns3xxx/cns3420vb.c
diff --git a/arch/arm/mach-cns3xxx/Kconfig b/arch/arm/mach-cns3xxx/Kconfig
index 20284cd..9ebfcc4 100644
--- a/arch/arm/mach-cns3xxx/Kconfig
+++ b/arch/arm/mach-cns3xxx/Kconfig
@@ -1,4 +1,12 @@
menu "CNS3XXX platform type"
depends on ARCH_CNS3XXX
+config MACH_CNS3420VB
+ bool "Support for CNS3420 Validation Board"
+ help
+ Include support for the Cavium Networks CNS3420 MPCore Platform
+ Baseboard.
+ This is a platform with an on-board ARM11 MPCore and has support
+ for USB, USB-OTG, MMC/SD/SDIO, SATA, PCI-E, etc.
+
endmenu
diff --git a/arch/arm/mach-cns3xxx/Makefile b/arch/arm/mach-cns3xxx/Makefile
index e5e76dd..427507a 100644
--- a/arch/arm/mach-cns3xxx/Makefile
+++ b/arch/arm/mach-cns3xxx/Makefile
@@ -1 +1,2 @@
obj-$(CONFIG_ARCH_CNS3XXX) += core.o pm.o
+obj-$(CONFIG_MACH_CNS3420VB) += cns3420vb.o
diff --git a/arch/arm/mach-cns3xxx/cns3420vb.c b/arch/arm/mach-cns3xxx/cns3420vb.c
new file mode 100644
index 0000000..2e30c82
--- /dev/null
+++ b/arch/arm/mach-cns3xxx/cns3420vb.c
@@ -0,0 +1,148 @@
+/*
+ * Cavium Networks CNS3420 Validation Board
+ *
+ * Copyright 2000 Deep Blue Solutions Ltd
+ * Copyright 2008 ARM Limited
+ * Copyright 2008 Cavium Networks
+ * Scott Shu
+ * Copyright 2010 MontaVista Software, LLC.
+ * Anton Vorontsov <avorontsov@mvista.com>
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/compiler.h>
+#include <linux/io.h>
+#include <linux/serial_core.h>
+#include <linux/serial_8250.h>
+#include <linux/platform_device.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/physmap.h>
+#include <linux/mtd/partitions.h>
+#include <asm/setup.h>
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/time.h>
+#include <mach/hardware.h>
+#include <mach/cns3xxx.h>
+#include <mach/irqs.h>
+#include "core.h"
+
+/*
+ * NOR Flash
+ */
+static struct mtd_partition cns3420_nor_partitions[] = {
+ {
+ .name = "uboot",
+ .size = 0x00040000,
+ .offset = 0,
+ .mask_flags = MTD_WRITEABLE,
+ }, {
+ .name = "kernel",
+ .size = 0x004C0000,
+ .offset = MTDPART_OFS_APPEND,
+ }, {
+ .name = "filesystem",
+ .size = 0x7000000,
+ .offset = MTDPART_OFS_APPEND,
+ }, {
+ .name = "filesystem2",
+ .size = 0x0AE0000,
+ .offset = MTDPART_OFS_APPEND,
+ }, {
+ .name = "ubootenv",
+ .size = MTDPART_SIZ_FULL,
+ .offset = MTDPART_OFS_APPEND,
+ },
+};
+
+static struct physmap_flash_data cns3420_nor_pdata = {
+ .width = 2,
+ .parts = cns3420_nor_partitions,
+ .nr_parts = ARRAY_SIZE(cns3420_nor_partitions),
+};
+
+static struct resource cns3420_nor_res = {
+ .start = CNS3XXX_FLASH_BASE,
+ .end = CNS3XXX_FLASH_BASE + SZ_128M - 1,
+ .flags = IORESOURCE_MEM | IORESOURCE_MEM_32BIT,
+};
+
+static struct platform_device cns3420_nor_pdev = {
+ .name = "physmap-flash",
+ .id = 0,
+ .resource = &cns3420_nor_res,
+ .num_resources = 1,
+ .dev = {
+ .platform_data = &cns3420_nor_pdata,
+ },
+};
+
+/*
+ * UART
+ */
+static void __init cns3420_early_serial_setup(void)
+{
+#ifdef CONFIG_SERIAL_8250_CONSOLE
+ static struct uart_port cns3420_serial_port = {
+ .membase = (void __iomem *)CNS3XXX_UART0_BASE_VIRT,
+ .mapbase = CNS3XXX_UART0_BASE,
+ .irq = IRQ_CNS3XXX_UART0,
+ .iotype = UPIO_MEM,
+ .flags = UPF_BOOT_AUTOCONF | UPF_FIXED_TYPE,
+ .regshift = 2,
+ .uartclk = 24000000,
+ .line = 0,
+ .type = PORT_16550A,
+ .fifosize = 16,
+ };
+
+ early_serial_setup(&cns3420_serial_port);
+#endif
+}
+
+/*
+ * Initialization
+ */
+static struct platform_device *cns3420_pdevs[] __initdata = {
+ &cns3420_nor_pdev,
+};
+
+static void __init cns3420_init(void)
+{
+ platform_add_devices(cns3420_pdevs, ARRAY_SIZE(cns3420_pdevs));
+
+ pm_power_off = cns3xxx_power_off;
+}
+
+static struct map_desc cns3420_io_desc[] __initdata = {
+ {
+ .virtual = CNS3XXX_UART0_BASE_VIRT,
+ .pfn = __phys_to_pfn(CNS3XXX_UART0_BASE),
+ .length = SZ_4K,
+ .type = MT_DEVICE,
+ },
+};
+
+static void __init cns3420_map_io(void)
+{
+ cns3xxx_map_io();
+ iotable_init(cns3420_io_desc, ARRAY_SIZE(cns3420_io_desc));
+
+ cns3420_early_serial_setup();
+}
+
+MACHINE_START(CNS3420VB, "Cavium Networks CNS3420 Validation Board")
+ .phys_io = CNS3XXX_UART0_BASE,
+ .io_pg_offst = (CNS3XXX_UART0_BASE_VIRT >> 18) & 0xfffc,
+ .boot_params = 0x00000100,
+ .map_io = cns3420_map_io,
+ .init_irq = cns3xxx_init_irq,
+ .timer = &cns3xxx_timer,
+ .init_machine = cns3420_init,
+MACHINE_END
--
1.7.0
^ permalink raw reply related [flat|nested] 4+ messages in thread