From: Alan Cox <alan@linux.intel.com>
To: linux-kernel@vger.kernel.org
Subject: [PATCH 02/14] tty: serial - fix tty back references in termios
Date: Thu, 01 Apr 2010 17:04:29 +0100 [thread overview]
Message-ID: <20100401160424.8882.1814.stgit@localhost.localdomain> (raw)
In-Reply-To: <20100401155513.8882.54006.stgit@localhost.localdomain>
One or two drivers go poking back into the tty from the termios setting
routine in unsafe ways. We don't need to pass the tty down because the
[ab]users are just using it to get at things they can get at anyway.
This leaves low_latency setting to sort out along with set_ldisc use.
Signed-off-by: Alan Cox <alan@linux.intel.com>
---
drivers/serial/21285.c | 10 +++-------
drivers/serial/imx.c | 10 ++++------
drivers/serial/ioc3_serial.c | 9 +++++----
drivers/serial/ioc4_serial.c | 9 +++++----
drivers/serial/max3100.c | 3 +--
5 files changed, 18 insertions(+), 23 deletions(-)
diff --git a/drivers/serial/21285.c b/drivers/serial/21285.c
index 8681f13..d89aa38 100644
--- a/drivers/serial/21285.c
+++ b/drivers/serial/21285.c
@@ -216,7 +216,7 @@ serial21285_set_termios(struct uart_port *port, struct ktermios *termios,
struct ktermios *old)
{
unsigned long flags;
- unsigned int baud, quot, h_lcr;
+ unsigned int baud, quot, h_lcr, b;
/*
* We don't support modem control lines.
@@ -234,12 +234,8 @@ serial21285_set_termios(struct uart_port *port, struct ktermios *termios,
*/
baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16);
quot = uart_get_divisor(port, baud);
-
- if (port->state && port->state->port.tty) {
- struct tty_struct *tty = port->state->port.tty;
- unsigned int b = port->uartclk / (16 * quot);
- tty_encode_baud_rate(tty, b, b);
- }
+ b = port->uartclk / (16 * quot);
+ tty_termios_encode_baud_rate(termios, b, b);
switch (termios->c_cflag & CSIZE) {
case CS5:
diff --git a/drivers/serial/imx.c b/drivers/serial/imx.c
index 4315b23..9504b44 100644
--- a/drivers/serial/imx.c
+++ b/drivers/serial/imx.c
@@ -901,13 +901,11 @@ imx_set_termios(struct uart_port *port, struct ktermios *termios,
rational_best_approximation(16 * div * baud, sport->port.uartclk,
1 << 16, 1 << 16, &num, &denom);
- if (port->state && port->state->port.tty) {
- tdiv64 = sport->port.uartclk;
- tdiv64 *= num;
- do_div(tdiv64, denom * 16 * div);
- tty_encode_baud_rate(sport->port.state->port.tty,
+ tdiv64 = sport->port.uartclk;
+ tdiv64 *= num;
+ do_div(tdiv64, denom * 16 * div);
+ tty_termios_encode_baud_rate(termios,
(speed_t)tdiv64, (speed_t)tdiv64);
- }
num -= 1;
denom -= 1;
diff --git a/drivers/serial/ioc3_serial.c b/drivers/serial/ioc3_serial.c
index f164ba4..bd2e9e6 100644
--- a/drivers/serial/ioc3_serial.c
+++ b/drivers/serial/ioc3_serial.c
@@ -954,12 +954,13 @@ ioc3_change_speed(struct uart_port *the_port,
struct ktermios *new_termios, struct ktermios *old_termios)
{
struct ioc3_port *port = get_ioc3_port(the_port);
- unsigned int cflag;
+ unsigned int cflag, iflag;
int baud;
int new_parity = 0, new_parity_enable = 0, new_stop = 0, new_data = 8;
struct uart_state *state = the_port->state;
cflag = new_termios->c_cflag;
+ iflag = new_termios->c_iflag;
switch (cflag & CSIZE) {
case CS5:
@@ -1000,12 +1001,12 @@ ioc3_change_speed(struct uart_port *the_port,
state->port.tty->low_latency = 1;
- if (I_IGNPAR(state->port.tty))
+ if (iflag & IGNPAR))
the_port->ignore_status_mask &= ~(N_PARITY_ERROR
| N_FRAMING_ERROR);
- if (I_IGNBRK(state->port.tty)) {
+ if (iflag & IGNBRK) {
the_port->ignore_status_mask &= ~N_BREAK;
- if (I_IGNPAR(state->port.tty))
+ if (iflag & IGNPAR)
the_port->ignore_status_mask &= ~N_OVERRUN_ERROR;
}
if (!(cflag & CREAD)) {
diff --git a/drivers/serial/ioc4_serial.c b/drivers/serial/ioc4_serial.c
index 8ad28fc..2c30023 100644
--- a/drivers/serial/ioc4_serial.c
+++ b/drivers/serial/ioc4_serial.c
@@ -1685,11 +1685,12 @@ ioc4_change_speed(struct uart_port *the_port,
{
struct ioc4_port *port = get_ioc4_port(the_port, 0);
int baud, bits;
- unsigned cflag;
+ unsigned cflag, iflag;
int new_parity = 0, new_parity_enable = 0, new_stop = 0, new_data = 8;
struct uart_state *state = the_port->state;
cflag = new_termios->c_cflag;
+ iflag = new_termios->c_iflag;
switch (cflag & CSIZE) {
case CS5:
@@ -1741,12 +1742,12 @@ ioc4_change_speed(struct uart_port *the_port,
state->port.tty->low_latency = 1;
- if (I_IGNPAR(state->port.tty))
+ if (iflag & IGNPAR)
the_port->ignore_status_mask &= ~(N_PARITY_ERROR
| N_FRAMING_ERROR);
- if (I_IGNBRK(state->port.tty)) {
+ if (iflag & IGNBRK) {
the_port->ignore_status_mask &= ~N_BREAK;
- if (I_IGNPAR(state->port.tty))
+ if (iflag & IGNPAR))
the_port->ignore_status_mask &= ~N_OVERRUN_ERROR;
}
if (!(cflag & CREAD)) {
diff --git a/drivers/serial/max3100.c b/drivers/serial/max3100.c
index 3351c3b..dfcabfe 100644
--- a/drivers/serial/max3100.c
+++ b/drivers/serial/max3100.c
@@ -430,7 +430,6 @@ max3100_set_termios(struct uart_port *port, struct ktermios *termios,
int baud = 0;
unsigned cflag;
u32 param_new, param_mask, parity = 0;
- struct tty_struct *tty = s->port.state->port.tty;
dev_dbg(&s->spi->dev, "%s\n", __func__);
if (!tty)
@@ -485,7 +484,7 @@ max3100_set_termios(struct uart_port *port, struct ktermios *termios,
default:
baud = s->baud;
}
- tty_encode_baud_rate(tty, baud, baud);
+ tty_termios_encode_baud_rate(termios, baud, baud);
s->baud = baud;
param_mask |= MAX3100_BAUD;
next prev parent reply other threads:[~2010-04-01 16:33 UTC|newest]
Thread overview: 18+ messages / expand[flat|nested] mbox.gz Atom feed top
2010-04-01 16:04 [RFC PATCH 00/14] Some BKL killing in the serial drivers Alan Cox
2010-04-01 16:04 ` [PATCH 01/14] tty: serial - fix tty referencing in set_ldisc Alan Cox
2010-04-01 16:04 ` Alan Cox [this message]
2010-04-01 16:04 ` [PATCH 03/14] tty: serial - fix various misuses/mishandlings of port->tty Alan Cox
2010-04-01 16:04 ` [PATCH 04/14] vc: Locking clean up Alan Cox
2010-04-30 20:30 ` Arnd Bergmann
2010-04-01 16:05 ` [PATCH 05/14] stallion: prune lock_kernel calls Alan Cox
2010-04-29 21:29 ` Arnd Bergmann
2010-04-30 19:32 ` Alan Cox
2010-04-01 16:05 ` [PATCH 06/14] istallion: use bit ops for the board flags Alan Cox
2010-04-01 16:05 ` [PATCH 07/14] riscom8: kill use of lock_kernel Alan Cox
2010-04-01 16:05 ` [PATCH 08/14] isicom: kill off the BKL Alan Cox
2010-04-01 16:06 ` [PATCH 09/14] rocket: kill BKL Alan Cox
2010-04-01 16:06 ` [PATCH 10/14] synclink: kill the big kernel lock Alan Cox
2010-04-01 16:06 ` [PATCH 11/14] cyclades: Kill off BKL usage Alan Cox
2010-04-01 16:06 ` [PATCH 12/14] epca: Kill the big kernel lock Alan Cox
2010-04-01 16:07 ` [PATCH 13/14] specialix; Kill the BKL Alan Cox
2010-04-01 16:07 ` [PATCH 14/14] synclink: reworking locking a bit Alan Cox
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20100401160424.8882.1814.stgit@localhost.localdomain \
--to=alan@linux.intel.com \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.