* [PATCH v3 0/3] Support for Cavium Networks CNS3xxx machines
@ 2010-03-30 19:02 Anton Vorontsov
2010-03-30 19:02 ` [PATCH 1/3] ARM: cns3xxx: Add basic support for Cavium Networks CNS3xxx processors Anton Vorontsov
` (3 more replies)
0 siblings, 4 replies; 7+ messages in thread
From: Anton Vorontsov @ 2010-03-30 19:02 UTC (permalink / raw)
To: linux-arm-kernel
Hi all,
v3 is on the way...
Changes since v2:
- We noticed that timer2 (which was used as a clock source) causes
nanosleep system call to misbehave. Until debugged, the timer2
support is removed.
It's fine since timer1 is still used as a clockevent, and provides
all needed timekeeping functionality. With these patches we want
a minimal (but rock solid) CNS3xxx support, all non-essential
features can wait.
I.e. support for the second timer can be added as a separate
patch.
- Updated some PCIe register definitions to make PCIe integration
more smooth.
- Updated defconfig.
Changes since v1:
- Addressed Russell's comments;
- CNS3420VB board support split into its own patch per Sergei's
comment;
- This series no longer include AHCI and SDHCI patches. Because of
dependencies on other trees they aren't yet suitable for inclusion,
so no need to repost them again.
Thanks!
--
Anton Vorontsov
email: cbouatmailru at gmail.com
irc://irc.freenode.net/bd2
^ permalink raw reply [flat|nested] 7+ messages in thread* [PATCH 1/3] ARM: cns3xxx: Add basic support for Cavium Networks CNS3xxx processors 2010-03-30 19:02 [PATCH v3 0/3] Support for Cavium Networks CNS3xxx machines Anton Vorontsov @ 2010-03-30 19:02 ` Anton Vorontsov 2010-04-14 15:40 ` Russell King - ARM Linux 2010-03-30 19:02 ` [PATCH 2/3] ARM: cns3xxx: Add CNS3420 Validation Board support Anton Vorontsov ` (2 subsequent siblings) 3 siblings, 1 reply; 7+ messages in thread From: Anton Vorontsov @ 2010-03-30 19:02 UTC (permalink / raw) To: linux-arm-kernel This patch adds very basic support for ECONA CNS3xxx ARM11 MPcore (ARMv6) dual-core processors. Note that SMP is not yet supported, as well as many peripheral devices. Support for these features will be added later. Signed-off-by: Anton Vorontsov <avorontsov@mvista.com> --- MAINTAINERS | 6 + arch/arm/Kconfig | 11 + arch/arm/Makefile | 1 + arch/arm/mach-cns3xxx/Kconfig | 4 + arch/arm/mach-cns3xxx/Makefile | 1 + arch/arm/mach-cns3xxx/Makefile.boot | 3 + arch/arm/mach-cns3xxx/core.c | 249 +++++++++ arch/arm/mach-cns3xxx/core.h | 23 + arch/arm/mach-cns3xxx/include/mach/cns3xxx.h | 635 ++++++++++++++++++++++ arch/arm/mach-cns3xxx/include/mach/debug-macro.S | 21 + arch/arm/mach-cns3xxx/include/mach/entry-macro.S | 82 +++ arch/arm/mach-cns3xxx/include/mach/hardware.h | 22 + arch/arm/mach-cns3xxx/include/mach/io.h | 22 + arch/arm/mach-cns3xxx/include/mach/irqs.h | 24 + arch/arm/mach-cns3xxx/include/mach/memory.h | 26 + arch/arm/mach-cns3xxx/include/mach/system.h | 29 + arch/arm/mach-cns3xxx/include/mach/timex.h | 12 + arch/arm/mach-cns3xxx/include/mach/uncompress.h | 55 ++ arch/arm/mach-cns3xxx/include/mach/vmalloc.h | 11 + arch/arm/mach-cns3xxx/pm.c | 86 +++ 20 files changed, 1323 insertions(+), 0 deletions(-) create mode 100644 arch/arm/mach-cns3xxx/Kconfig create mode 100644 arch/arm/mach-cns3xxx/Makefile create mode 100644 arch/arm/mach-cns3xxx/Makefile.boot create mode 100644 arch/arm/mach-cns3xxx/core.c create mode 100644 arch/arm/mach-cns3xxx/core.h create mode 100644 arch/arm/mach-cns3xxx/include/mach/cns3xxx.h create mode 100644 arch/arm/mach-cns3xxx/include/mach/debug-macro.S create mode 100644 arch/arm/mach-cns3xxx/include/mach/entry-macro.S create mode 100644 arch/arm/mach-cns3xxx/include/mach/hardware.h create mode 100644 arch/arm/mach-cns3xxx/include/mach/io.h create mode 100644 arch/arm/mach-cns3xxx/include/mach/irqs.h create mode 100644 arch/arm/mach-cns3xxx/include/mach/memory.h create mode 100644 arch/arm/mach-cns3xxx/include/mach/system.h create mode 100644 arch/arm/mach-cns3xxx/include/mach/timex.h create mode 100644 arch/arm/mach-cns3xxx/include/mach/uncompress.h create mode 100644 arch/arm/mach-cns3xxx/include/mach/vmalloc.h create mode 100644 arch/arm/mach-cns3xxx/pm.c diff --git a/MAINTAINERS b/MAINTAINERS index 449d444..93ebdf8 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -586,6 +586,12 @@ F: drivers/mtd/nand/bcm_umi_bch.c F: drivers/mtd/nand/bcm_umi_hamming.c F: drivers/mtd/nand/nand_bcm_umi.h +ARM/CAVIUM NETWORKS CNS3XXX MACHINE SUPPORT +M: Anton Vorontsov <avorontsov@mvista.com> +S: Maintained +F: arch/arm/mach-cns3xxx/ +T: git git://git.infradead.org/users/cbou/linux-cns3xxx.git + ARM/CIRRUS LOGIC EP93XX ARM ARCHITECTURE M: Hartley Sweeten <hsweeten@visionengravers.com> M: Ryan Mallon <ryan@bluewatersys.com> diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig index c5408bf..d779e25 100644 --- a/arch/arm/Kconfig +++ b/arch/arm/Kconfig @@ -296,6 +296,15 @@ config ARCH_CLPS711X help Support for Cirrus Logic 711x/721x based boards. +config ARCH_CNS3XXX + bool "Cavium Networks CNS3XXX family" + select CPU_V6 + select GENERIC_TIME + select GENERIC_CLOCKEVENTS + select ARM_GIC + help + Support for Cavium Networks CNS3XXX platform. + config ARCH_GEMINI bool "Cortina Systems Gemini" select CPU_FA526 @@ -816,6 +825,8 @@ source "arch/arm/mach-bcmring/Kconfig" source "arch/arm/mach-clps711x/Kconfig" +source "arch/arm/mach-cns3xxx/Kconfig" + source "arch/arm/mach-davinci/Kconfig" source "arch/arm/mach-dove/Kconfig" diff --git a/arch/arm/Makefile b/arch/arm/Makefile index ed820e7..3e312ec 100644 --- a/arch/arm/Makefile +++ b/arch/arm/Makefile @@ -121,6 +121,7 @@ machine-$(CONFIG_ARCH_AAEC2000) := aaec2000 machine-$(CONFIG_ARCH_AT91) := at91 machine-$(CONFIG_ARCH_BCMRING) := bcmring machine-$(CONFIG_ARCH_CLPS711X) := clps711x +machine-$(CONFIG_ARCH_CNS3XXX) := cns3xxx machine-$(CONFIG_ARCH_DAVINCI) := davinci machine-$(CONFIG_ARCH_DOVE) := dove machine-$(CONFIG_ARCH_EBSA110) := ebsa110 diff --git a/arch/arm/mach-cns3xxx/Kconfig b/arch/arm/mach-cns3xxx/Kconfig new file mode 100644 index 0000000..20284cd --- /dev/null +++ b/arch/arm/mach-cns3xxx/Kconfig @@ -0,0 +1,4 @@ +menu "CNS3XXX platform type" + depends on ARCH_CNS3XXX + +endmenu diff --git a/arch/arm/mach-cns3xxx/Makefile b/arch/arm/mach-cns3xxx/Makefile new file mode 100644 index 0000000..e5e76dd --- /dev/null +++ b/arch/arm/mach-cns3xxx/Makefile @@ -0,0 +1 @@ +obj-$(CONFIG_ARCH_CNS3XXX) += core.o pm.o diff --git a/arch/arm/mach-cns3xxx/Makefile.boot b/arch/arm/mach-cns3xxx/Makefile.boot new file mode 100644 index 0000000..7770128 --- /dev/null +++ b/arch/arm/mach-cns3xxx/Makefile.boot @@ -0,0 +1,3 @@ + zreladdr-y := 0x00008000 +params_phys-y := 0x00000100 +initrd_phys-y := 0x00C00000 diff --git a/arch/arm/mach-cns3xxx/core.c b/arch/arm/mach-cns3xxx/core.c new file mode 100644 index 0000000..9ca4d58 --- /dev/null +++ b/arch/arm/mach-cns3xxx/core.c @@ -0,0 +1,249 @@ +/* + * Copyright 1999 - 2003 ARM Limited + * Copyright 2000 Deep Blue Solutions Ltd + * Copyright 2008 Cavium Networks + * + * This file is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License, Version 2, as + * published by the Free Software Foundation. + */ + +#include <linux/init.h> +#include <linux/interrupt.h> +#include <linux/clockchips.h> +#include <linux/io.h> +#include <asm/mach/map.h> +#include <asm/mach/time.h> +#include <asm/mach/irq.h> +#include <asm/hardware/gic.h> +#include <mach/cns3xxx.h> +#include "core.h" + +static struct map_desc cns3xxx_io_desc[] __initdata = { + { + .virtual = CNS3XXX_TC11MP_TWD_BASE_VIRT, + .pfn = __phys_to_pfn(CNS3XXX_TC11MP_TWD_BASE), + .length = SZ_4K, + .type = MT_DEVICE, + }, { + .virtual = CNS3XXX_TC11MP_GIC_CPU_BASE_VIRT, + .pfn = __phys_to_pfn(CNS3XXX_TC11MP_GIC_CPU_BASE), + .length = SZ_4K, + .type = MT_DEVICE, + }, { + .virtual = CNS3XXX_TC11MP_GIC_DIST_BASE_VIRT, + .pfn = __phys_to_pfn(CNS3XXX_TC11MP_GIC_DIST_BASE), + .length = SZ_4K, + .type = MT_DEVICE, + }, { + .virtual = CNS3XXX_TIMER1_2_3_BASE_VIRT, + .pfn = __phys_to_pfn(CNS3XXX_TIMER1_2_3_BASE), + .length = SZ_4K, + .type = MT_DEVICE, + }, { + .virtual = CNS3XXX_GPIOA_BASE_VIRT, + .pfn = __phys_to_pfn(CNS3XXX_GPIOA_BASE), + .length = SZ_4K, + .type = MT_DEVICE, + }, { + .virtual = CNS3XXX_GPIOB_BASE_VIRT, + .pfn = __phys_to_pfn(CNS3XXX_GPIOB_BASE), + .length = SZ_4K, + .type = MT_DEVICE, + }, { + .virtual = CNS3XXX_MISC_BASE_VIRT, + .pfn = __phys_to_pfn(CNS3XXX_MISC_BASE), + .length = SZ_4K, + .type = MT_DEVICE, + }, { + .virtual = CNS3XXX_PM_BASE_VIRT, + .pfn = __phys_to_pfn(CNS3XXX_PM_BASE), + .length = SZ_4K, + .type = MT_DEVICE, + }, +}; + +void __init cns3xxx_map_io(void) +{ + iotable_init(cns3xxx_io_desc, ARRAY_SIZE(cns3xxx_io_desc)); +} + +/* used by entry-macro.S */ +void __iomem *gic_cpu_base_addr; + +void __init cns3xxx_init_irq(void) +{ + gic_cpu_base_addr = __io(CNS3XXX_TC11MP_GIC_CPU_BASE_VIRT); + gic_dist_init(0, __io(CNS3XXX_TC11MP_GIC_DIST_BASE_VIRT), 29); + gic_cpu_init(0, gic_cpu_base_addr); +} + +void cns3xxx_power_off(void) +{ + u32 __iomem *pm_base = __io(CNS3XXX_PM_BASE_VIRT); + u32 clkctrl; + + printk(KERN_INFO "powering system down...\n"); + + clkctrl = readl(pm_base + PM_SYS_CLK_CTRL_OFFSET); + clkctrl &= 0xfffff1ff; + clkctrl |= (0x5 << 9); /* Hibernate */ + writel(clkctrl, pm_base + PM_SYS_CLK_CTRL_OFFSET); + +} + +/* + * Timer + */ +static void __iomem *cns3xxx_tmr1; + +static void cns3xxx_timer_set_mode(enum clock_event_mode mode, + struct clock_event_device *clk) +{ + unsigned long ctrl = readl(cns3xxx_tmr1 + TIMER1_2_CONTROL_OFFSET); + int pclk = cns3xxx_cpu_clock() / 8; + int reload; + + switch (mode) { + case CLOCK_EVT_MODE_PERIODIC: + reload = pclk * 20 / (3 * HZ) * 0x25000; + writel(reload, cns3xxx_tmr1 + TIMER1_AUTO_RELOAD_OFFSET); + ctrl |= (1 << 0) | (1 << 2) | (1 << 9); + break; + case CLOCK_EVT_MODE_ONESHOT: + /* period set, and timer enabled in 'next_event' hook */ + ctrl |= (1 << 2) | (1 << 9); + break; + case CLOCK_EVT_MODE_UNUSED: + case CLOCK_EVT_MODE_SHUTDOWN: + default: + ctrl = 0; + } + + writel(ctrl, cns3xxx_tmr1 + TIMER1_2_CONTROL_OFFSET); +} + +static int cns3xxx_timer_set_next_event(unsigned long evt, + struct clock_event_device *unused) +{ + unsigned long ctrl = readl(cns3xxx_tmr1 + TIMER1_2_CONTROL_OFFSET); + + writel(evt, cns3xxx_tmr1 + TIMER1_AUTO_RELOAD_OFFSET); + writel(ctrl | (1 << 0), cns3xxx_tmr1 + TIMER1_2_CONTROL_OFFSET); + + return 0; +} + +static struct clock_event_device cns3xxx_tmr1_clockevent = { + .name = "cns3xxx timer1", + .shift = 8, + .features = CLOCK_EVT_FEAT_PERIODIC | CLOCK_EVT_FEAT_ONESHOT, + .set_mode = cns3xxx_timer_set_mode, + .set_next_event = cns3xxx_timer_set_next_event, + .rating = 350, + .cpumask = cpu_all_mask, +}; + +static void __init cns3xxx_clockevents_init(unsigned int timer_irq) +{ + cns3xxx_tmr1_clockevent.irq = timer_irq; + cns3xxx_tmr1_clockevent.mult = + div_sc((cns3xxx_cpu_clock() >> 3) * 1000000, NSEC_PER_SEC, + cns3xxx_tmr1_clockevent.shift); + cns3xxx_tmr1_clockevent.max_delta_ns = + clockevent_delta2ns(0xffffffff, &cns3xxx_tmr1_clockevent); + cns3xxx_tmr1_clockevent.min_delta_ns = + clockevent_delta2ns(0xf, &cns3xxx_tmr1_clockevent); + + clockevents_register_device(&cns3xxx_tmr1_clockevent); +} + +/* + * IRQ handler for the timer + */ +static irqreturn_t cns3xxx_timer_interrupt(int irq, void *dev_id) +{ + struct clock_event_device *evt = &cns3xxx_tmr1_clockevent; + u32 __iomem *stat = cns3xxx_tmr1 + TIMER1_2_INTERRUPT_STATUS_OFFSET; + u32 val; + + /* Clear the interrupt */ + val = readl(stat); + writel(val & ~(1 << 2), stat); + + evt->event_handler(evt); + + return IRQ_HANDLED; +} + +static struct irqaction cns3xxx_timer_irq = { + .name = "timer", + .flags = IRQF_DISABLED | IRQF_TIMER | IRQF_IRQPOLL, + .handler = cns3xxx_timer_interrupt, +}; + +/* + * Set up the clock source and clock events devices + */ +static void __init __cns3xxx_timer_init(unsigned int timer_irq) +{ + u32 val; + u32 irq_mask; + + /* + * Initialise to a known state (all timers off) + */ + + /* disable timer1 and timer2 */ + writel(0, cns3xxx_tmr1 + TIMER1_2_CONTROL_OFFSET); + /* stop free running timer3 */ + writel(0, cns3xxx_tmr1 + TIMER_FREERUN_CONTROL_OFFSET); + + /* timer1 */ + writel(0x5C800, cns3xxx_tmr1 + TIMER1_COUNTER_OFFSET); + writel(0x5C800, cns3xxx_tmr1 + TIMER1_AUTO_RELOAD_OFFSET); + + writel(0, cns3xxx_tmr1 + TIMER1_MATCH_V1_OFFSET); + writel(0, cns3xxx_tmr1 + TIMER1_MATCH_V2_OFFSET); + + /* mask irq, non-mask timer1 overflow */ + irq_mask = readl(cns3xxx_tmr1 + TIMER1_2_INTERRUPT_MASK_OFFSET); + irq_mask &= ~(1 << 2); + irq_mask |= 0x03; + writel(irq_mask, cns3xxx_tmr1 + TIMER1_2_INTERRUPT_MASK_OFFSET); + + /* down counter */ + val = readl(cns3xxx_tmr1 + TIMER1_2_CONTROL_OFFSET); + val |= (1 << 9); + writel(val, cns3xxx_tmr1 + TIMER1_2_CONTROL_OFFSET); + + /* timer2 */ + writel(0, cns3xxx_tmr1 + TIMER2_MATCH_V1_OFFSET); + writel(0, cns3xxx_tmr1 + TIMER2_MATCH_V2_OFFSET); + + /* mask irq */ + irq_mask = readl(cns3xxx_tmr1 + TIMER1_2_INTERRUPT_MASK_OFFSET); + irq_mask |= ((1 << 3) | (1 << 4) | (1 << 5)); + writel(irq_mask, cns3xxx_tmr1 + TIMER1_2_INTERRUPT_MASK_OFFSET); + + /* down counter */ + val = readl(cns3xxx_tmr1 + TIMER1_2_CONTROL_OFFSET); + val |= (1 << 10); + writel(val, cns3xxx_tmr1 + TIMER1_2_CONTROL_OFFSET); + + /* Make irqs happen for the system timer */ + setup_irq(timer_irq, &cns3xxx_timer_irq); + + cns3xxx_clockevents_init(timer_irq); +} + +static void __init cns3xxx_timer_init(void) +{ + cns3xxx_tmr1 = __io(CNS3XXX_TIMER1_2_3_BASE_VIRT); + + __cns3xxx_timer_init(IRQ_CNS3XXX_TIMER0); +} + +struct sys_timer cns3xxx_timer = { + .init = cns3xxx_timer_init, +}; diff --git a/arch/arm/mach-cns3xxx/core.h b/arch/arm/mach-cns3xxx/core.h new file mode 100644 index 0000000..6b33ec1 --- /dev/null +++ b/arch/arm/mach-cns3xxx/core.h @@ -0,0 +1,23 @@ +/* + * Copyright 2000 Deep Blue Solutions Ltd + * Copyright 2004 ARM Limited + * Copyright 2008 Cavium Networks + * + * This file is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License, Version 2, as + * published by the Free Software Foundation. + */ + +#ifndef __CNS3XXX_CORE_H +#define __CNS3XXX_CORE_H + +extern void __iomem *gic_cpu_base_addr; +extern struct sys_timer cns3xxx_timer; + +void __init cns3xxx_map_io(void); +void __init cns3xxx_init_irq(void); +void cns3xxx_power_off(void); +void cns3xxx_pwr_power_up(unsigned int block); +void cns3xxx_pwr_power_down(unsigned int block); + +#endif /* __CNS3XXX_CORE_H */ diff --git a/arch/arm/mach-cns3xxx/include/mach/cns3xxx.h b/arch/arm/mach-cns3xxx/include/mach/cns3xxx.h new file mode 100644 index 0000000..8a2f5a2 --- /dev/null +++ b/arch/arm/mach-cns3xxx/include/mach/cns3xxx.h @@ -0,0 +1,635 @@ +/* + * Copyright 2008 Cavium Networks + * + * This file is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License, Version 2, as + * published by the Free Software Foundation. + */ + +#ifndef __MACH_BOARD_CNS3XXXH +#define __MACH_BOARD_CNS3XXXH + +/* + * Memory map + */ +#define CNS3XXX_FLASH_BASE 0x10000000 /* Flash/SRAM Memory Bank 0 */ +#define CNS3XXX_FLASH_SIZE SZ_256M + +#define CNS3XXX_DDR2SDRAM_BASE 0x20000000 /* DDR2 SDRAM Memory */ + +#define CNS3XXX_SPI_FLASH_BASE 0x60000000 /* SPI Serial Flash Memory */ + +#define CNS3XXX_SWITCH_BASE 0x70000000 /* Switch and HNAT Control */ +#define CNS3XXX_SWITCH_BASE_VIRT 0xFFF00000 + +#define CNS3XXX_PPE_BASE 0x70001000 /* HANT */ +#define CNS3XXX_PPE_BASE_VIRT 0xFFF50000 + +#define CNS3XXX_EMBEDDED_SRAM_BASE 0x70002000 /* HANT Embedded SRAM */ +#define CNS3XXX_EMBEDDED_SRAM_BASE_VIRT 0xFFF60000 + +#define CNS3XXX_SSP_BASE 0x71000000 /* Synchronous Serial Port - SPI/PCM/I2C */ +#define CNS3XXX_SSP_BASE_VIRT 0xFFF01000 + +#define CNS3XXX_DMC_BASE 0x72000000 /* DMC Control (DDR2 SDRAM) */ +#define CNS3XXX_DMC_BASE_VIRT 0xFFF02000 + +#define CNS3XXX_SMC_BASE 0x73000000 /* SMC Control */ +#define CNS3XXX_SMC_BASE_VIRT 0xFFF03000 + +#define SMC_MEMC_STATUS_OFFSET 0x000 +#define SMC_MEMIF_CFG_OFFSET 0x004 +#define SMC_MEMC_CFG_SET_OFFSET 0x008 +#define SMC_MEMC_CFG_CLR_OFFSET 0x00C +#define SMC_DIRECT_CMD_OFFSET 0x010 +#define SMC_SET_CYCLES_OFFSET 0x014 +#define SMC_SET_OPMODE_OFFSET 0x018 +#define SMC_REFRESH_PERIOD_0_OFFSET 0x020 +#define SMC_REFRESH_PERIOD_1_OFFSET 0x024 +#define SMC_SRAM_CYCLES0_0_OFFSET 0x100 +#define SMC_NAND_CYCLES0_0_OFFSET 0x100 +#define SMC_OPMODE0_0_OFFSET 0x104 +#define SMC_SRAM_CYCLES0_1_OFFSET 0x120 +#define SMC_NAND_CYCLES0_1_OFFSET 0x120 +#define SMC_OPMODE0_1_OFFSET 0x124 +#define SMC_USER_STATUS_OFFSET 0x200 +#define SMC_USER_CONFIG_OFFSET 0x204 +#define SMC_ECC_STATUS_OFFSET 0x300 +#define SMC_ECC_MEMCFG_OFFSET 0x304 +#define SMC_ECC_MEMCOMMAND1_OFFSET 0x308 +#define SMC_ECC_MEMCOMMAND2_OFFSET 0x30C +#define SMC_ECC_ADDR0_OFFSET 0x310 +#define SMC_ECC_ADDR1_OFFSET 0x314 +#define SMC_ECC_VALUE0_OFFSET 0x318 +#define SMC_ECC_VALUE1_OFFSET 0x31C +#define SMC_ECC_VALUE2_OFFSET 0x320 +#define SMC_ECC_VALUE3_OFFSET 0x324 +#define SMC_PERIPH_ID_0_OFFSET 0xFE0 +#define SMC_PERIPH_ID_1_OFFSET 0xFE4 +#define SMC_PERIPH_ID_2_OFFSET 0xFE8 +#define SMC_PERIPH_ID_3_OFFSET 0xFEC +#define SMC_PCELL_ID_0_OFFSET 0xFF0 +#define SMC_PCELL_ID_1_OFFSET 0xFF4 +#define SMC_PCELL_ID_2_OFFSET 0xFF8 +#define SMC_PCELL_ID_3_OFFSET 0xFFC + +#define CNS3XXX_GPIOA_BASE 0x74000000 /* GPIO port A */ +#define CNS3XXX_GPIOA_BASE_VIRT 0xFFF04000 + +#define CNS3XXX_GPIOB_BASE 0x74800000 /* GPIO port B */ +#define CNS3XXX_GPIOB_BASE_VIRT 0xFFF05000 + +#define CNS3XXX_RTC_BASE 0x75000000 /* Real Time Clock */ +#define CNS3XXX_RTC_BASE_VIRT 0xFFF06000 + +#define RTC_SEC_OFFSET 0x00 +#define RTC_MIN_OFFSET 0x04 +#define RTC_HOUR_OFFSET 0x08 +#define RTC_DAY_OFFSET 0x0C +#define RTC_SEC_ALM_OFFSET 0x10 +#define RTC_MIN_ALM_OFFSET 0x14 +#define RTC_HOUR_ALM_OFFSET 0x18 +#define RTC_REC_OFFSET 0x1C +#define RTC_CTRL_OFFSET 0x20 +#define RTC_INTR_STS_OFFSET 0x34 + +#define CNS3XXX_MISC_BASE 0x76000000 /* Misc Control */ +#define CNS3XXX_MISC_BASE_VIRT 0xFFF07000 /* Misc Control */ + +#define CNS3XXX_PM_BASE 0x77000000 /* Power Management Control */ +#define CNS3XXX_PM_BASE_VIRT 0xFFF08000 + +#define PM_CLK_GATE_OFFSET 0x00 +#define PM_SOFT_RST_OFFSET 0x04 +#define PM_HS_CFG_OFFSET 0x08 +#define PM_CACTIVE_STA_OFFSET 0x0C +#define PM_PWR_STA_OFFSET 0x10 +#define PM_SYS_CLK_CTRL_OFFSET 0x14 +#define PM_PLL_LCD_I2S_CTRL_OFFSET 0x18 +#define PM_PLL_HM_PD_OFFSET 0x1C + +#define CNS3XXX_UART0_BASE 0x78000000 /* UART 0 */ +#define CNS3XXX_UART0_BASE_VIRT 0xFFF09000 + +#define CNS3XXX_UART1_BASE 0x78400000 /* UART 1 */ +#define CNS3XXX_UART1_BASE_VIRT 0xFFF0A000 + +#define CNS3XXX_UART2_BASE 0x78800000 /* UART 2 */ +#define CNS3XXX_UART2_BASE_VIRT 0xFFF0B000 + +#define CNS3XXX_DMAC_BASE 0x79000000 /* Generic DMA Control */ +#define CNS3XXX_DMAC_BASE_VIRT 0xFFF0D000 + +#define CNS3XXX_CORESIGHT_BASE 0x7A000000 /* CoreSight */ +#define CNS3XXX_CORESIGHT_BASE_VIRT 0xFFF0E000 + +#define CNS3XXX_CRYPTO_BASE 0x7B000000 /* Crypto */ +#define CNS3XXX_CRYPTO_BASE_VIRT 0xFFF0F000 + +#define CNS3XXX_I2S_BASE 0x7C000000 /* I2S */ +#define CNS3XXX_I2S_BASE_VIRT 0xFFF10000 + +#define CNS3XXX_TIMER1_2_3_BASE 0x7C800000 /* Timer */ +#define CNS3XXX_TIMER1_2_3_BASE_VIRT 0xFFF10800 + +#define TIMER1_COUNTER_OFFSET 0x00 +#define TIMER1_AUTO_RELOAD_OFFSET 0x04 +#define TIMER1_MATCH_V1_OFFSET 0x08 +#define TIMER1_MATCH_V2_OFFSET 0x0C + +#define TIMER2_COUNTER_OFFSET 0x10 +#define TIMER2_AUTO_RELOAD_OFFSET 0x14 +#define TIMER2_MATCH_V1_OFFSET 0x18 +#define TIMER2_MATCH_V2_OFFSET 0x1C + +#define TIMER1_2_CONTROL_OFFSET 0x30 +#define TIMER1_2_INTERRUPT_STATUS_OFFSET 0x34 +#define TIMER1_2_INTERRUPT_MASK_OFFSET 0x38 + +#define TIMER_FREERUN_OFFSET 0x40 +#define TIMER_FREERUN_CONTROL_OFFSET 0x44 + +#define CNS3XXX_HCIE_BASE 0x7D000000 /* HCIE Control */ +#define CNS3XXX_HCIE_BASE_VIRT 0xFFF30000 + +#define CNS3XXX_RAID_BASE 0x7E000000 /* RAID Control */ +#define CNS3XXX_RAID_BASE_VIRT 0xFFF12000 + +#define CNS3XXX_AXI_IXC_BASE 0x7F000000 /* AXI IXC */ +#define CNS3XXX_AXI_IXC_BASE_VIRT 0xFFF13000 + +#define CNS3XXX_CLCD_BASE 0x80000000 /* LCD Control */ +#define CNS3XXX_CLCD_BASE_VIRT 0xFFF14000 + +#define CNS3XXX_USBOTG_BASE 0x81000000 /* USB OTG Control */ +#define CNS3XXX_USBOTG_BASE_VIRT 0xFFF15000 + +#define CNS3XXX_USB_BASE 0x82000000 /* USB Host Control */ +#define CNS3XXX_USB_BASE_VIRT 0xFFF16000 + +#define CNS3XXX_SATA2_BASE 0x83000000 /* SATA */ +#define CNS3XXX_SATA2_SIZE SZ_16M +#define CNS3XXX_SATA2_BASE_VIRT 0xFFF17000 + +#define CNS3XXX_CAMERA_BASE 0x84000000 /* Camera Interface */ +#define CNS3XXX_CAMERA_BASE_VIRT 0xFFF18000 + +#define CNS3XXX_SDIO_BASE 0x85000000 /* SDIO */ +#define CNS3XXX_SDIO_BASE_VIRT 0xFFF19000 + +#define CNS3XXX_I2S_TDM_BASE 0x86000000 /* I2S TDM */ +#define CNS3XXX_I2S_TDM_BASE_VIRT 0xFFF1A000 + +#define CNS3XXX_2DG_BASE 0x87000000 /* 2D Graphic Control */ +#define CNS3XXX_2DG_BASE_VIRT 0xFFF1B000 + +#define CNS3XXX_USB_OHCI_BASE 0x88000000 /* USB OHCI */ +#define CNS3XXX_USB_OHCI_BASE_VIRT 0xFFF1C000 + +#define CNS3XXX_L2C_BASE 0x92000000 /* L2 Cache Control */ +#define CNS3XXX_L2C_BASE_VIRT 0xFFF27000 + +#define CNS3XXX_PCIE0_MEM_BASE 0xA0000000 /* PCIe Port 0 IO/Memory Space */ +#define CNS3XXX_PCIE0_MEM_BASE_VIRT 0xE0000000 + +#define CNS3XXX_PCIE0_HOST_BASE 0xAB000000 /* PCIe Port 0 RC Base */ +#define CNS3XXX_PCIE0_HOST_BASE_VIRT 0xE1000000 + +#define CNS3XXX_PCIE0_IO_BASE 0xAC000000 /* PCIe Port 0 */ +#define CNS3XXX_PCIE0_IO_BASE_VIRT 0xE2000000 + +#define CNS3XXX_PCIE0_CFG0_BASE 0xAD000000 /* PCIe Port 0 CFG Type 0 */ +#define CNS3XXX_PCIE0_CFG0_BASE_VIRT 0xE3000000 + +#define CNS3XXX_PCIE0_CFG1_BASE 0xAE000000 /* PCIe Port 0 CFG Type 1 */ +#define CNS3XXX_PCIE0_CFG1_BASE_VIRT 0xE4000000 + +#define CNS3XXX_PCIE0_MSG_BASE 0xAF000000 /* PCIe Port 0 Message Space */ +#define CNS3XXX_PCIE0_MSG_BASE_VIRT 0xE5000000 + +#define CNS3XXX_PCIE1_MEM_BASE 0xB0000000 /* PCIe Port 1 IO/Memory Space */ +#define CNS3XXX_PCIE1_MEM_BASE_VIRT 0xE8000000 + +#define CNS3XXX_PCIE1_HOST_BASE 0xBB000000 /* PCIe Port 1 RC Base */ +#define CNS3XXX_PCIE1_HOST_BASE_VIRT 0xE9000000 + +#define CNS3XXX_PCIE1_IO_BASE 0xBC000000 /* PCIe Port 1 */ +#define CNS3XXX_PCIE1_IO_BASE_VIRT 0xEA000000 + +#define CNS3XXX_PCIE1_CFG0_BASE 0xBD000000 /* PCIe Port 1 CFG Type 0 */ +#define CNS3XXX_PCIE1_CFG0_BASE_VIRT 0xEB000000 + +#define CNS3XXX_PCIE1_CFG1_BASE 0xBE000000 /* PCIe Port 1 CFG Type 1 */ +#define CNS3XXX_PCIE1_CFG1_BASE_VIRT 0xEC000000 + +#define CNS3XXX_PCIE1_MSG_BASE 0xBF000000 /* PCIe Port 1 Message Space */ +#define CNS3XXX_PCIE1_MSG_BASE_VIRT 0xED000000 + +/* + * Testchip peripheral and fpga gic regions + */ +#define CNS3XXX_TC11MP_SCU_BASE 0x90000000 /* IRQ, Test chip */ +#define CNS3XXX_TC11MP_SCU_BASE_VIRT 0xFF000000 + +#define CNS3XXX_TC11MP_GIC_CPU_BASE 0x90000100 /* Test chip interrupt controller CPU interface */ +#define CNS3XXX_TC11MP_GIC_CPU_BASE_VIRT 0xFF000100 + +#define CNS3XXX_TC11MP_TWD_BASE 0x90000600 +#define CNS3XXX_TC11MP_TWD_BASE_VIRT 0xFF000600 + +#define CNS3XXX_TC11MP_GIC_DIST_BASE 0x90001000 /* Test chip interrupt controller distributor */ +#define CNS3XXX_TC11MP_GIC_DIST_BASE_VIRT 0xFF001000 + +#define CNS3XXX_TC11MP_L220_BASE 0x92002000 /* L220 registers */ +#define CNS3XXX_TC11MP_L220_BASE_VIRT 0xFF002000 + +/* + * Misc block + */ +#define MISC_MEM_MAP(offs) (void __iomem *)(CNS3XXX_MISC_BASE_VIRT + (offs)) +#define MISC_MEM_MAP_VALUE(offset) (*((volatile unsigned int *)(CNS3XXX_MISC_BASE_VIRT + (offset)))) + +#define MISC_MEMORY_REMAP_REG MISC_MEM_MAP_VALUE(0x00) +#define MISC_CHIP_CONFIG_REG MISC_MEM_MAP_VALUE(0x04) +#define MISC_DEBUG_PROBE_DATA_REG MISC_MEM_MAP_VALUE(0x08) +#define MISC_DEBUG_PROBE_SELECTION_REG MISC_MEM_MAP_VALUE(0x0C) +#define MISC_IO_PIN_FUNC_SELECTION_REG MISC_MEM_MAP_VALUE(0x10) +#define MISC_GPIOA_PIN_ENABLE_REG MISC_MEM_MAP_VALUE(0x14) +#define MISC_GPIOB_PIN_ENABLE_REG MISC_MEM_MAP_VALUE(0x18) +#define MISC_IO_PAD_DRIVE_STRENGTH_CTRL_A MISC_MEM_MAP_VALUE(0x1C) +#define MISC_IO_PAD_DRIVE_STRENGTH_CTRL_B MISC_MEM_MAP_VALUE(0x20) +#define MISC_GPIOA_15_0_PULL_CTRL_REG MISC_MEM_MAP_VALUE(0x24) +#define MISC_GPIOA_16_31_PULL_CTRL_REG MISC_MEM_MAP_VALUE(0x28) +#define MISC_GPIOB_15_0_PULL_CTRL_REG MISC_MEM_MAP_VALUE(0x2C) +#define MISC_GPIOB_16_31_PULL_CTRL_REG MISC_MEM_MAP_VALUE(0x30) +#define MISC_IO_PULL_CTRL_REG MISC_MEM_MAP_VALUE(0x34) +#define MISC_E_FUSE_31_0_REG MISC_MEM_MAP_VALUE(0x40) +#define MISC_E_FUSE_63_32_REG MISC_MEM_MAP_VALUE(0x44) +#define MISC_E_FUSE_95_64_REG MISC_MEM_MAP_VALUE(0x48) +#define MISC_E_FUSE_127_96_REG MISC_MEM_MAP_VALUE(0x4C) +#define MISC_SOFTWARE_TEST_1_REG MISC_MEM_MAP_VALUE(0x50) +#define MISC_SOFTWARE_TEST_2_REG MISC_MEM_MAP_VALUE(0x54) + +#define MISC_SATA_POWER_MODE MISC_MEM_MAP_VALUE(0x310) + +#define MISC_USB_CFG_REG MISC_MEM_MAP_VALUE(0x800) +#define MISC_USB_STS_REG MISC_MEM_MAP_VALUE(0x804) +#define MISC_USBPHY00_CFG_REG MISC_MEM_MAP_VALUE(0x808) +#define MISC_USBPHY01_CFG_REG MISC_MEM_MAP_VALUE(0x80c) +#define MISC_USBPHY10_CFG_REG MISC_MEM_MAP_VALUE(0x810) +#define MISC_USBPHY11_CFG_REG MISC_MEM_MAP_VALUE(0x814) + +#define MISC_PCIEPHY_CMCTL(x) MISC_MEM_MAP(0x900 + (x) * 0x004) +#define MISC_PCIEPHY_CTL(x) MISC_MEM_MAP(0x940 + (x) * 0x100) +#define MISC_PCIE_AXIS_AWMISC(x) MISC_MEM_MAP(0x944 + (x) * 0x100) +#define MISC_PCIE_AXIS_ARMISC(x) MISC_MEM_MAP(0x948 + (x) * 0x100) +#define MISC_PCIE_AXIS_RMISC(x) MISC_MEM_MAP(0x94C + (x) * 0x100) +#define MISC_PCIE_AXIS_BMISC(x) MISC_MEM_MAP(0x950 + (x) * 0x100) +#define MISC_PCIE_AXIM_RMISC(x) MISC_MEM_MAP(0x954 + (x) * 0x100) +#define MISC_PCIE_AXIM_BMISC(x) MISC_MEM_MAP(0x958 + (x) * 0x100) +#define MISC_PCIE_CTRL(x) MISC_MEM_MAP(0x95C + (x) * 0x100) +#define MISC_PCIE_PM_DEBUG(x) MISC_MEM_MAP(0x960 + (x) * 0x100) +#define MISC_PCIE_RFC_DEBUG(x) MISC_MEM_MAP(0x964 + (x) * 0x100) +#define MISC_PCIE_CXPL_DEBUGL(x) MISC_MEM_MAP(0x968 + (x) * 0x100) +#define MISC_PCIE_CXPL_DEBUGH(x) MISC_MEM_MAP(0x96C + (x) * 0x100) +#define MISC_PCIE_DIAG_DEBUGH(x) MISC_MEM_MAP(0x970 + (x) * 0x100) +#define MISC_PCIE_W1CLR(x) MISC_MEM_MAP(0x974 + (x) * 0x100) +#define MISC_PCIE_INT_MASK(x) MISC_MEM_MAP(0x978 + (x) * 0x100) +#define MISC_PCIE_INT_STATUS(x) MISC_MEM_MAP(0x97C + (x) * 0x100) + +/* + * Power management and clock control + */ +#define PMU_REG_VALUE(offset) (*((volatile unsigned int *)(CNS3XXX_PM_BASE_VIRT + (offset)))) + +#define PM_CLK_GATE_REG PMU_REG_VALUE(0x000) +#define PM_SOFT_RST_REG PMU_REG_VALUE(0x004) +#define PM_HS_CFG_REG PMU_REG_VALUE(0x008) +#define PM_CACTIVE_STA_REG PMU_REG_VALUE(0x00C) +#define PM_PWR_STA_REG PMU_REG_VALUE(0x010) +#define PM_CLK_CTRL_REG PMU_REG_VALUE(0x014) +#define PM_PLL_LCD_I2S_CTRL_REG PMU_REG_VALUE(0x018) +#define PM_PLL_HM_PD_CTRL_REG PMU_REG_VALUE(0x01C) +#define PM_REGULAT_CTRL_REG PMU_REG_VALUE(0x020) +#define PM_WDT_CTRL_REG PMU_REG_VALUE(0x024) +#define PM_WU_CTRL0_REG PMU_REG_VALUE(0x028) +#define PM_WU_CTRL1_REG PMU_REG_VALUE(0x02C) +#define PM_CSR_REG PMU_REG_VALUE(0x030) + +/* PM_CLK_GATE_REG */ +#define PM_CLK_GATE_REG_OFFSET_SDIO (25) +#define PM_CLK_GATE_REG_OFFSET_GPU (24) +#define PM_CLK_GATE_REG_OFFSET_CIM (23) +#define PM_CLK_GATE_REG_OFFSET_LCDC (22) +#define PM_CLK_GATE_REG_OFFSET_I2S (21) +#define PM_CLK_GATE_REG_OFFSET_RAID (20) +#define PM_CLK_GATE_REG_OFFSET_SATA (19) +#define PM_CLK_GATE_REG_OFFSET_PCIE(x) (17 + (x)) +#define PM_CLK_GATE_REG_OFFSET_USB_HOST (16) +#define PM_CLK_GATE_REG_OFFSET_USB_OTG (15) +#define PM_CLK_GATE_REG_OFFSET_TIMER (14) +#define PM_CLK_GATE_REG_OFFSET_CRYPTO (13) +#define PM_CLK_GATE_REG_OFFSET_HCIE (12) +#define PM_CLK_GATE_REG_OFFSET_SWITCH (11) +#define PM_CLK_GATE_REG_OFFSET_GPIO (10) +#define PM_CLK_GATE_REG_OFFSET_UART3 (9) +#define PM_CLK_GATE_REG_OFFSET_UART2 (8) +#define PM_CLK_GATE_REG_OFFSET_UART1 (7) +#define PM_CLK_GATE_REG_OFFSET_RTC (5) +#define PM_CLK_GATE_REG_OFFSET_GDMA (4) +#define PM_CLK_GATE_REG_OFFSET_SPI_PCM_I2C (3) +#define PM_CLK_GATE_REG_OFFSET_SMC_NFI (1) +#define PM_CLK_GATE_REG_MASK (0x03FFFFBA) + +/* PM_SOFT_RST_REG */ +#define PM_SOFT_RST_REG_OFFST_WARM_RST_FLAG (31) +#define PM_SOFT_RST_REG_OFFST_CPU1 (29) +#define PM_SOFT_RST_REG_OFFST_CPU0 (28) +#define PM_SOFT_RST_REG_OFFST_SDIO (25) +#define PM_SOFT_RST_REG_OFFST_GPU (24) +#define PM_SOFT_RST_REG_OFFST_CIM (23) +#define PM_SOFT_RST_REG_OFFST_LCDC (22) +#define PM_SOFT_RST_REG_OFFST_I2S (21) +#define PM_SOFT_RST_REG_OFFST_RAID (20) +#define PM_SOFT_RST_REG_OFFST_SATA (19) +#define PM_SOFT_RST_REG_OFFST_PCIE(x) (17 + (x)) +#define PM_SOFT_RST_REG_OFFST_USB_HOST (16) +#define PM_SOFT_RST_REG_OFFST_USB_OTG (15) +#define PM_SOFT_RST_REG_OFFST_TIMER (14) +#define PM_SOFT_RST_REG_OFFST_CRYPTO (13) +#define PM_SOFT_RST_REG_OFFST_HCIE (12) +#define PM_SOFT_RST_REG_OFFST_SWITCH (11) +#define PM_SOFT_RST_REG_OFFST_GPIO (10) +#define PM_SOFT_RST_REG_OFFST_UART3 (9) +#define PM_SOFT_RST_REG_OFFST_UART2 (8) +#define PM_SOFT_RST_REG_OFFST_UART1 (7) +#define PM_SOFT_RST_REG_OFFST_RTC (5) +#define PM_SOFT_RST_REG_OFFST_GDMA (4) +#define PM_SOFT_RST_REG_OFFST_SPI_PCM_I2C (3) +#define PM_SOFT_RST_REG_OFFST_DMC (2) +#define PM_SOFT_RST_REG_OFFST_SMC_NFI (1) +#define PM_SOFT_RST_REG_OFFST_GLOBAL (0) +#define PM_SOFT_RST_REG_MASK (0xF3FFFFBF) + +/* PMHS_CFG_REG */ +#define PM_HS_CFG_REG_OFFSET_SDIO (25) +#define PM_HS_CFG_REG_OFFSET_GPU (24) +#define PM_HS_CFG_REG_OFFSET_CIM (23) +#define PM_HS_CFG_REG_OFFSET_LCDC (22) +#define PM_HS_CFG_REG_OFFSET_I2S (21) +#define PM_HS_CFG_REG_OFFSET_RAID (20) +#define PM_HS_CFG_REG_OFFSET_SATA (19) +#define PM_HS_CFG_REG_OFFSET_PCIE1 (18) +#define PM_HS_CFG_REG_OFFSET_PCIE0 (17) +#define PM_HS_CFG_REG_OFFSET_USB_HOST (16) +#define PM_HS_CFG_REG_OFFSET_USB_OTG (15) +#define PM_HS_CFG_REG_OFFSET_TIMER (14) +#define PM_HS_CFG_REG_OFFSET_CRYPTO (13) +#define PM_HS_CFG_REG_OFFSET_HCIE (12) +#define PM_HS_CFG_REG_OFFSET_SWITCH (11) +#define PM_HS_CFG_REG_OFFSET_GPIO (10) +#define PM_HS_CFG_REG_OFFSET_UART3 (9) +#define PM_HS_CFG_REG_OFFSET_UART2 (8) +#define PM_HS_CFG_REG_OFFSET_UART1 (7) +#define PM_HS_CFG_REG_OFFSET_RTC (5) +#define PM_HS_CFG_REG_OFFSET_GDMA (4) +#define PM_HS_CFG_REG_OFFSET_SPI_PCM_I2S (3) +#define PM_HS_CFG_REG_OFFSET_DMC (2) +#define PM_HS_CFG_REG_OFFSET_SMC_NFI (1) +#define PM_HS_CFG_REG_MASK (0x03FFFFBE) +#define PM_HS_CFG_REG_MASK_SUPPORT (0x01100806) + +/* PM_CACTIVE_STA_REG */ +#define PM_CACTIVE_STA_REG_OFFSET_SDIO (25) +#define PM_CACTIVE_STA_REG_OFFSET_GPU (24) +#define PM_CACTIVE_STA_REG_OFFSET_CIM (23) +#define PM_CACTIVE_STA_REG_OFFSET_LCDC (22) +#define PM_CACTIVE_STA_REG_OFFSET_I2S (21) +#define PM_CACTIVE_STA_REG_OFFSET_RAID (20) +#define PM_CACTIVE_STA_REG_OFFSET_SATA (19) +#define PM_CACTIVE_STA_REG_OFFSET_PCIE1 (18) +#define PM_CACTIVE_STA_REG_OFFSET_PCIE0 (17) +#define PM_CACTIVE_STA_REG_OFFSET_USB_HOST (16) +#define PM_CACTIVE_STA_REG_OFFSET_USB_OTG (15) +#define PM_CACTIVE_STA_REG_OFFSET_TIMER (14) +#define PM_CACTIVE_STA_REG_OFFSET_CRYPTO (13) +#define PM_CACTIVE_STA_REG_OFFSET_HCIE (12) +#define PM_CACTIVE_STA_REG_OFFSET_SWITCH (11) +#define PM_CACTIVE_STA_REG_OFFSET_GPIO (10) +#define PM_CACTIVE_STA_REG_OFFSET_UART3 (9) +#define PM_CACTIVE_STA_REG_OFFSET_UART2 (8) +#define PM_CACTIVE_STA_REG_OFFSET_UART1 (7) +#define PM_CACTIVE_STA_REG_OFFSET_RTC (5) +#define PM_CACTIVE_STA_REG_OFFSET_GDMA (4) +#define PM_CACTIVE_STA_REG_OFFSET_SPI_PCM_I2S (3) +#define PM_CACTIVE_STA_REG_OFFSET_DMC (2) +#define PM_CACTIVE_STA_REG_OFFSET_SMC_NFI (1) +#define PM_CACTIVE_STA_REG_MASK (0x03FFFFBE) + +/* PM_PWR_STA_REG */ +#define PM_PWR_STA_REG_REG_OFFSET_SDIO (25) +#define PM_PWR_STA_REG_REG_OFFSET_GPU (24) +#define PM_PWR_STA_REG_REG_OFFSET_CIM (23) +#define PM_PWR_STA_REG_REG_OFFSET_LCDC (22) +#define PM_PWR_STA_REG_REG_OFFSET_I2S (21) +#define PM_PWR_STA_REG_REG_OFFSET_RAID (20) +#define PM_PWR_STA_REG_REG_OFFSET_SATA (19) +#define PM_PWR_STA_REG_REG_OFFSET_PCIE1 (18) +#define PM_PWR_STA_REG_REG_OFFSET_PCIE0 (17) +#define PM_PWR_STA_REG_REG_OFFSET_USB_HOST (16) +#define PM_PWR_STA_REG_REG_OFFSET_USB_OTG (15) +#define PM_PWR_STA_REG_REG_OFFSET_TIMER (14) +#define PM_PWR_STA_REG_REG_OFFSET_CRYPTO (13) +#define PM_PWR_STA_REG_REG_OFFSET_HCIE (12) +#define PM_PWR_STA_REG_REG_OFFSET_SWITCH (11) +#define PM_PWR_STA_REG_REG_OFFSET_GPIO (10) +#define PM_PWR_STA_REG_REG_OFFSET_UART3 (9) +#define PM_PWR_STA_REG_REG_OFFSET_UART2 (8) +#define PM_PWR_STA_REG_REG_OFFSET_UART1 (7) +#define PM_PWR_STA_REG_REG_OFFSET_RTC (5) +#define PM_PWR_STA_REG_REG_OFFSET_GDMA (4) +#define PM_PWR_STA_REG_REG_OFFSET_SPI_PCM_I2S (3) +#define PM_PWR_STA_REG_REG_OFFSET_DMC (2) +#define PM_PWR_STA_REG_REG_OFFSET_SMC_NFI (1) +#define PM_PWR_STA_REG_REG_MASK (0x03FFFFBE) + +/* PM_CLK_CTRL_REG */ +#define PM_CLK_CTRL_REG_OFFSET_I2S_MCLK (31) +#define PM_CLK_CTRL_REG_OFFSET_DDR2_CHG_EN (30) +#define PM_CLK_CTRL_REG_OFFSET_PCIE_REF1_EN (29) +#define PM_CLK_CTRL_REG_OFFSET_PCIE_REF0_EN (28) +#define PM_CLK_CTRL_REG_OFFSET_TIMER_SIM_MODE (27) +#define PM_CLK_CTRL_REG_OFFSET_I2SCLK_DIV (24) +#define PM_CLK_CTRL_REG_OFFSET_I2SCLK_SEL (22) +#define PM_CLK_CTRL_REG_OFFSET_CLKOUT_DIV (20) +#define PM_CLK_CTRL_REG_OFFSET_CLKOUT_SEL (16) +#define PM_CLK_CTRL_REG_OFFSET_MDC_DIV (14) +#define PM_CLK_CTRL_REG_OFFSET_CRYPTO_CLK_SEL (12) +#define PM_CLK_CTRL_REG_OFFSET_CPU_PWR_MODE (9) +#define PM_CLK_CTRL_REG_OFFSET_PLL_DDR2_SEL (7) +#define PM_CLK_CTRL_REG_OFFSET_DIV_IMMEDIATE (6) +#define PM_CLK_CTRL_REG_OFFSET_CPU_CLK_DIV (4) +#define PM_CLK_CTRL_REG_OFFSET_PLL_CPU_SEL (0) + +#define PM_CPU_CLK_DIV(DIV) { \ + PM_CLK_CTRL_REG &= ~((0x3) << PM_CLK_CTRL_REG_OFFSET_CPU_CLK_DIV); \ + PM_CLK_CTRL_REG |= (((DIV)&0x3) << PM_CLK_CTRL_REG_OFFSET_CPU_CLK_DIV); \ +} + +#define PM_PLL_CPU_SEL(CPU) { \ + PM_CLK_CTRL_REG &= ~((0xF) << PM_CLK_CTRL_REG_OFFSET_PLL_CPU_SEL); \ + PM_CLK_CTRL_REG |= (((CPU)&0xF) << PM_CLK_CTRL_REG_OFFSET_PLL_CPU_SEL); \ +} + +/* PM_PLL_LCD_I2S_CTRL_REG */ +#define PM_PLL_LCD_I2S_CTRL_REG_OFFSET_MCLK_SMC_DIV (22) +#define PM_PLL_LCD_I2S_CTRL_REG_OFFSET_R_SEL (17) +#define PM_PLL_LCD_I2S_CTRL_REG_OFFSET_PLL_LCD_P (11) +#define PM_PLL_LCD_I2S_CTRL_REG_OFFSET_PLL_LCD_M (3) +#define PM_PLL_LCD_I2S_CTRL_REG_OFFSET_PLL_LCD_S (0) + +/* PM_PLL_HM_PD_CTRL_REG */ +#define PM_PLL_HM_PD_CTRL_REG_OFFSET_SATA_PHY1 (11) +#define PM_PLL_HM_PD_CTRL_REG_OFFSET_SATA_PHY0 (10) +#define PM_PLL_HM_PD_CTRL_REG_OFFSET_PLL_I2SCD (6) +#define PM_PLL_HM_PD_CTRL_REG_OFFSET_PLL_I2S (5) +#define PM_PLL_HM_PD_CTRL_REG_OFFSET_PLL_LCD (4) +#define PM_PLL_HM_PD_CTRL_REG_OFFSET_PLL_USB (3) +#define PM_PLL_HM_PD_CTRL_REG_OFFSET_PLL_RGMII (2) +#define PM_PLL_HM_PD_CTRL_REG_MASK (0x00000C7C) + +/* PM_WDT_CTRL_REG */ +#define PM_WDT_CTRL_REG_OFFSET_RESET_CPU_ONLY (0) + +/* PM_CSR_REG - Clock Scaling Register*/ +#define PM_CSR_REG_OFFSET_CSR_EN (30) +#define PM_CSR_REG_OFFSET_CSR_NUM (0) + +#define CNS3XXX_PWR_CLK_EN(BLOCK) (0x1<<PM_CLK_GATE_REG_OFFSET_##BLOCK) + +/* Software reset*/ +#define CNS3XXX_PWR_SOFTWARE_RST(BLOCK) (0x1<<PM_SOFT_RST_REG_OFFST_##BLOCK) + +/* + * CNS3XXX support several power saving mode as following, + * DFS, IDLE, HALT, DOZE, SLEEP, Hibernate + */ +#define CNS3XXX_PWR_CPU_MODE_DFS (0) +#define CNS3XXX_PWR_CPU_MODE_IDLE (1) +#define CNS3XXX_PWR_CPU_MODE_HALT (2) +#define CNS3XXX_PWR_CPU_MODE_DOZE (3) +#define CNS3XXX_PWR_CPU_MODE_SLEEP (4) +#define CNS3XXX_PWR_CPU_MODE_HIBERNATE (5) + +#define CNS3XXX_PWR_PLL(BLOCK) (0x1<<PM_PLL_HM_PD_CTRL_REG_OFFSET_##BLOCK) +#define CNS3XXX_PWR_PLL_ALL PM_PLL_HM_PD_CTRL_REG_MASK + +/* Change CPU frequency and divider */ +#define CNS3XXX_PWR_PLL_CPU_300MHZ (0) +#define CNS3XXX_PWR_PLL_CPU_333MHZ (1) +#define CNS3XXX_PWR_PLL_CPU_366MHZ (2) +#define CNS3XXX_PWR_PLL_CPU_400MHZ (3) +#define CNS3XXX_PWR_PLL_CPU_433MHZ (4) +#define CNS3XXX_PWR_PLL_CPU_466MHZ (5) +#define CNS3XXX_PWR_PLL_CPU_500MHZ (6) +#define CNS3XXX_PWR_PLL_CPU_533MHZ (7) +#define CNS3XXX_PWR_PLL_CPU_566MHZ (8) +#define CNS3XXX_PWR_PLL_CPU_600MHZ (9) +#define CNS3XXX_PWR_PLL_CPU_633MHZ (10) +#define CNS3XXX_PWR_PLL_CPU_666MHZ (11) +#define CNS3XXX_PWR_PLL_CPU_700MHZ (12) + +#define CNS3XXX_PWR_CPU_CLK_DIV_BY1 (0) +#define CNS3XXX_PWR_CPU_CLK_DIV_BY2 (1) +#define CNS3XXX_PWR_CPU_CLK_DIV_BY4 (2) + +/* Change DDR2 frequency */ +#define CNS3XXX_PWR_PLL_DDR2_200MHZ (0) +#define CNS3XXX_PWR_PLL_DDR2_266MHZ (1) +#define CNS3XXX_PWR_PLL_DDR2_333MHZ (2) +#define CNS3XXX_PWR_PLL_DDR2_400MHZ (3) + +void cns3xxx_pwr_soft_rst(unsigned int block); +void cns3xxx_pwr_clk_en(unsigned int block); +int cns3xxx_cpu_clock(void); + +/* + * ARM11 MPCore interrupt sources (primary GIC) + */ +#define IRQ_CNS3XXX_PMU (IRQ_TC11MP_GIC_START + 0) +#define IRQ_CNS3XXX_SDIO (IRQ_TC11MP_GIC_START + 1) +#define IRQ_CNS3XXX_L2CC (IRQ_TC11MP_GIC_START + 2) +#define IRQ_CNS3XXX_RTC (IRQ_TC11MP_GIC_START + 3) +#define IRQ_CNS3XXX_I2S (IRQ_TC11MP_GIC_START + 4) +#define IRQ_CNS3XXX_PCM (IRQ_TC11MP_GIC_START + 5) +#define IRQ_CNS3XXX_SPI (IRQ_TC11MP_GIC_START + 6) +#define IRQ_CNS3XXX_I2C (IRQ_TC11MP_GIC_START + 7) +#define IRQ_CNS3XXX_CIM (IRQ_TC11MP_GIC_START + 8) +#define IRQ_CNS3XXX_GPU (IRQ_TC11MP_GIC_START + 9) +#define IRQ_CNS3XXX_LCD (IRQ_TC11MP_GIC_START + 10) +#define IRQ_CNS3XXX_GPIOA (IRQ_TC11MP_GIC_START + 11) +#define IRQ_CNS3XXX_GPIOB (IRQ_TC11MP_GIC_START + 12) +#define IRQ_CNS3XXX_UART0 (IRQ_TC11MP_GIC_START + 13) +#define IRQ_CNS3XXX_UART1 (IRQ_TC11MP_GIC_START + 14) +#define IRQ_CNS3XXX_UART2 (IRQ_TC11MP_GIC_START + 15) +#define IRQ_CNS3XXX_ARM11 (IRQ_TC11MP_GIC_START + 16) + +#define IRQ_CNS3XXX_SW_STATUS (IRQ_TC11MP_GIC_START + 17) +#define IRQ_CNS3XXX_SW_R0TXC (IRQ_TC11MP_GIC_START + 18) +#define IRQ_CNS3XXX_SW_R0RXC (IRQ_TC11MP_GIC_START + 19) +#define IRQ_CNS3XXX_SW_R0QE (IRQ_TC11MP_GIC_START + 20) +#define IRQ_CNS3XXX_SW_R0QF (IRQ_TC11MP_GIC_START + 21) +#define IRQ_CNS3XXX_SW_R1TXC (IRQ_TC11MP_GIC_START + 22) +#define IRQ_CNS3XXX_SW_R1RXC (IRQ_TC11MP_GIC_START + 23) +#define IRQ_CNS3XXX_SW_R1QE (IRQ_TC11MP_GIC_START + 24) +#define IRQ_CNS3XXX_SW_R1QF (IRQ_TC11MP_GIC_START + 25) +#define IRQ_CNS3XXX_SW_PPE (IRQ_TC11MP_GIC_START + 26) + +#define IRQ_CNS3XXX_CRYPTO (IRQ_TC11MP_GIC_START + 27) +#define IRQ_CNS3XXX_HCIE (IRQ_TC11MP_GIC_START + 28) +#define IRQ_CNS3XXX_PCIE0_DEVICE (IRQ_TC11MP_GIC_START + 29) +#define IRQ_CNS3XXX_PCIE1_DEVICE (IRQ_TC11MP_GIC_START + 30) +#define IRQ_CNS3XXX_USB_OTG (IRQ_TC11MP_GIC_START + 31) +#define IRQ_CNS3XXX_USB_EHCI (IRQ_TC11MP_GIC_START + 32) +#define IRQ_CNS3XXX_SATA (IRQ_TC11MP_GIC_START + 33) +#define IRQ_CNS3XXX_RAID (IRQ_TC11MP_GIC_START + 34) +#define IRQ_CNS3XXX_SMC (IRQ_TC11MP_GIC_START + 35) + +#define IRQ_CNS3XXX_DMAC_ABORT (IRQ_TC11MP_GIC_START + 36) +#define IRQ_CNS3XXX_DMAC0 (IRQ_TC11MP_GIC_START + 37) +#define IRQ_CNS3XXX_DMAC1 (IRQ_TC11MP_GIC_START + 38) +#define IRQ_CNS3XXX_DMAC2 (IRQ_TC11MP_GIC_START + 39) +#define IRQ_CNS3XXX_DMAC3 (IRQ_TC11MP_GIC_START + 40) +#define IRQ_CNS3XXX_DMAC4 (IRQ_TC11MP_GIC_START + 41) +#define IRQ_CNS3XXX_DMAC5 (IRQ_TC11MP_GIC_START + 42) +#define IRQ_CNS3XXX_DMAC6 (IRQ_TC11MP_GIC_START + 43) +#define IRQ_CNS3XXX_DMAC7 (IRQ_TC11MP_GIC_START + 44) +#define IRQ_CNS3XXX_DMAC8 (IRQ_TC11MP_GIC_START + 45) +#define IRQ_CNS3XXX_DMAC9 (IRQ_TC11MP_GIC_START + 46) +#define IRQ_CNS3XXX_DMAC10 (IRQ_TC11MP_GIC_START + 47) +#define IRQ_CNS3XXX_DMAC11 (IRQ_TC11MP_GIC_START + 48) +#define IRQ_CNS3XXX_DMAC12 (IRQ_TC11MP_GIC_START + 49) +#define IRQ_CNS3XXX_DMAC13 (IRQ_TC11MP_GIC_START + 50) +#define IRQ_CNS3XXX_DMAC14 (IRQ_TC11MP_GIC_START + 51) +#define IRQ_CNS3XXX_DMAC15 (IRQ_TC11MP_GIC_START + 52) +#define IRQ_CNS3XXX_DMAC16 (IRQ_TC11MP_GIC_START + 53) +#define IRQ_CNS3XXX_DMAC17 (IRQ_TC11MP_GIC_START + 54) + +#define IRQ_CNS3XXX_PCIE0_RC (IRQ_TC11MP_GIC_START + 55) +#define IRQ_CNS3XXX_PCIE1_RC (IRQ_TC11MP_GIC_START + 56) +#define IRQ_CNS3XXX_TIMER0 (IRQ_TC11MP_GIC_START + 57) +#define IRQ_CNS3XXX_TIMER1 (IRQ_TC11MP_GIC_START + 58) +#define IRQ_CNS3XXX_USB_OHCI (IRQ_TC11MP_GIC_START + 59) +#define IRQ_CNS3XXX_TIMER2 (IRQ_TC11MP_GIC_START + 60) +#define IRQ_CNS3XXX_EXTERNAL_PIN0 (IRQ_TC11MP_GIC_START + 61) +#define IRQ_CNS3XXX_EXTERNAL_PIN1 (IRQ_TC11MP_GIC_START + 62) +#define IRQ_CNS3XXX_EXTERNAL_PIN2 (IRQ_TC11MP_GIC_START + 63) + +#define NR_IRQS_CNS3XXX (IRQ_TC11MP_GIC_START + 64) + +#if !defined(NR_IRQS) || (NR_IRQS < NR_IRQS_CNS3XXX) +#undef NR_IRQS +#define NR_IRQS NR_IRQS_CNS3XXX +#endif + +#endif /* __MACH_BOARD_CNS3XXX_H */ diff --git a/arch/arm/mach-cns3xxx/include/mach/debug-macro.S b/arch/arm/mach-cns3xxx/include/mach/debug-macro.S new file mode 100644 index 0000000..d16ce7e --- /dev/null +++ b/arch/arm/mach-cns3xxx/include/mach/debug-macro.S @@ -0,0 +1,21 @@ +/* + * Debugging macro include header + * + * Copyright 1994-1999 Russell King + * Copyright 2008 Cavium Networks + * Moved from linux/arch/arm/kernel/debug.S by Ben Dooks + * + * This file is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License, Version 2, as + * published by the Free Software Foundation. + */ + + .macro addruart,rx + mrc p15, 0, \rx, c1, c0 + tst \rx, #1 @ MMU enabled? + moveq \rx, #0x10000000 + movne \rx, #0xf0000000 @ virtual base + orr \rx, \rx, #0x00009000 + .endm + +#include <asm/hardware/debug-pl01x.S> diff --git a/arch/arm/mach-cns3xxx/include/mach/entry-macro.S b/arch/arm/mach-cns3xxx/include/mach/entry-macro.S new file mode 100644 index 0000000..5e1c554 --- /dev/null +++ b/arch/arm/mach-cns3xxx/include/mach/entry-macro.S @@ -0,0 +1,82 @@ +/* + * Low-level IRQ helper macros for Cavium Networks platforms + * + * Copyright 2008 Cavium Networks + * + * This file is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License, Version 2, as + * published by the Free Software Foundation. + */ + +#include <mach/hardware.h> +#include <asm/hardware/gic.h> + + .macro disable_fiq + .endm + + .macro get_irqnr_preamble, base, tmp + ldr \base, =gic_cpu_base_addr + ldr \base, [\base] + .endm + + .macro arch_ret_to_user, tmp1, tmp2 + .endm + + /* + * The interrupt numbering scheme is defined in the + * interrupt controller spec. To wit: + * + * Interrupts 0-15 are IPI + * 16-28 are reserved + * 29-31 are local. We allow 30 to be used for the watchdog. + * 32-1020 are global + * 1021-1022 are reserved + * 1023 is "spurious" (no interrupt) + * + * For now, we ignore all local interrupts so only return an interrupt if it's + * between 30 and 1020. The test_for_ipi routine below will pick up on IPIs. + * + * A simple read from the controller will tell us the number of the highest + * priority enabled interrupt. We then just need to check whether it is in the + * valid range for an IRQ (30-1020 inclusive). + */ + + .macro get_irqnr_and_base, irqnr, irqstat, base, tmp + + ldr \irqstat, [\base, #GIC_CPU_INTACK] /* bits 12-10 = src CPU, 9-0 = int # */ + + ldr \tmp, =1021 + + bic \irqnr, \irqstat, #0x1c00 + + cmp \irqnr, #29 + cmpcc \irqnr, \irqnr + cmpne \irqnr, \tmp + cmpcs \irqnr, \irqnr + + .endm + + /* We assume that irqstat (the raw value of the IRQ acknowledge + * register) is preserved from the macro above. + * If there is an IPI, we immediately signal end of interrupt on the + * controller, since this requires the original irqstat value which + * we won't easily be able to recreate later. + */ + + .macro test_for_ipi, irqnr, irqstat, base, tmp + bic \irqnr, \irqstat, #0x1c00 + cmp \irqnr, #16 + strcc \irqstat, [\base, #GIC_CPU_EOI] + cmpcs \irqnr, \irqnr + .endm + + /* As above, this assumes that irqstat and base are preserved.. */ + + .macro test_for_ltirq, irqnr, irqstat, base, tmp + bic \irqnr, \irqstat, #0x1c00 + mov \tmp, #0 + cmp \irqnr, #29 + moveq \tmp, #1 + streq \irqstat, [\base, #GIC_CPU_EOI] + cmp \tmp, #0 + .endm diff --git a/arch/arm/mach-cns3xxx/include/mach/hardware.h b/arch/arm/mach-cns3xxx/include/mach/hardware.h new file mode 100644 index 0000000..57e0983 --- /dev/null +++ b/arch/arm/mach-cns3xxx/include/mach/hardware.h @@ -0,0 +1,22 @@ +/* + * This file contains the hardware definitions of the Cavium Networks boards. + * + * Copyright 2003 ARM Limited. + * Copyright 2008 Cavium Networks + * + * This file is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License, Version 2, as + * published by the Free Software Foundation. + */ + +#ifndef __MACH_HARDWARE_H +#define __MACH_HARDWARE_H + +#include <asm/sizes.h> + +/* macro to get at IO space when running virtually */ +#define PCIBIOS_MIN_IO 0x00000000 +#define PCIBIOS_MIN_MEM 0x00000000 +#define pcibios_assign_all_busses() 1 + +#endif diff --git a/arch/arm/mach-cns3xxx/include/mach/io.h b/arch/arm/mach-cns3xxx/include/mach/io.h new file mode 100644 index 0000000..b4ff09a --- /dev/null +++ b/arch/arm/mach-cns3xxx/include/mach/io.h @@ -0,0 +1,22 @@ +/* + * Copyright 2008 Cavium Networks + * Copyright 2003 ARM Limited + * + * This file is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License, Version 2, as + * published by the Free Software Foundation. + */ +#ifndef __MACH_IO_H +#define __MACH_IO_H + +#define IO_SPACE_LIMIT 0xffffffff + +static inline void __iomem *__io(unsigned long addr) +{ + return (void __iomem *)addr; +} + +#define __io(a) __typesafe_io(a) +#define __mem_pci(a) (a) + +#endif diff --git a/arch/arm/mach-cns3xxx/include/mach/irqs.h b/arch/arm/mach-cns3xxx/include/mach/irqs.h new file mode 100644 index 0000000..2ab96f8 --- /dev/null +++ b/arch/arm/mach-cns3xxx/include/mach/irqs.h @@ -0,0 +1,24 @@ +/* + * Copyright 2000 Deep Blue Solutions Ltd. + * Copyright 2003 ARM Limited + * Copyright 2008 Cavium Networks + * + * This file is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License, Version 2, as + * published by the Free Software Foundation. + */ + +#ifndef __MACH_IRQS_H +#define __MACH_IRQS_H + +#define IRQ_LOCALTIMER 29 +#define IRQ_LOCALWDOG 30 +#define IRQ_TC11MP_GIC_START 32 + +#include <mach/cns3xxx.h> + +#ifndef NR_IRQS +#error "NR_IRQS not defined by the board-specific files" +#endif + +#endif diff --git a/arch/arm/mach-cns3xxx/include/mach/memory.h b/arch/arm/mach-cns3xxx/include/mach/memory.h new file mode 100644 index 0000000..3b6b769 --- /dev/null +++ b/arch/arm/mach-cns3xxx/include/mach/memory.h @@ -0,0 +1,26 @@ +/* + * Copyright 2003 ARM Limited + * Copyright 2008 Cavium Networks + * + * This file is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License, Version 2, as + * published by the Free Software Foundation. + */ + +#ifndef __MACH_MEMORY_H +#define __MACH_MEMORY_H + +/* + * Physical DRAM offset. + */ +#define PHYS_OFFSET UL(0x00000000) + +#define __phys_to_bus(x) ((x) + PHYS_OFFSET) +#define __bus_to_phys(x) ((x) - PHYS_OFFSET) + +#define __virt_to_bus(v) __phys_to_bus(__virt_to_phys(v)) +#define __bus_to_virt(b) __phys_to_virt(__bus_to_phys(b)) +#define __pfn_to_bus(p) __phys_to_bus(__pfn_to_phys(p)) +#define __bus_to_pfn(b) __phys_to_pfn(__bus_to_phys(b)) + +#endif diff --git a/arch/arm/mach-cns3xxx/include/mach/system.h b/arch/arm/mach-cns3xxx/include/mach/system.h new file mode 100644 index 0000000..58bb03a --- /dev/null +++ b/arch/arm/mach-cns3xxx/include/mach/system.h @@ -0,0 +1,29 @@ +/* + * Copyright 2000 Deep Blue Solutions Ltd + * Copyright 2003 ARM Limited + * Copyright 2008 Cavium Networks + * + * This file is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License, Version 2, as + * published by the Free Software Foundation. + */ + +#ifndef __MACH_SYSTEM_H +#define __MACH_SYSTEM_H + +#include <linux/io.h> +#include <asm/proc-fns.h> +#include <mach/hardware.h> + +static inline void arch_idle(void) +{ + /* + * This should do all the clock switching + * and wait for interrupt tricks + */ + cpu_do_idle(); +} + +void arch_reset(char mode, const char *cmd); + +#endif diff --git a/arch/arm/mach-cns3xxx/include/mach/timex.h b/arch/arm/mach-cns3xxx/include/mach/timex.h new file mode 100644 index 0000000..1fd0421 --- /dev/null +++ b/arch/arm/mach-cns3xxx/include/mach/timex.h @@ -0,0 +1,12 @@ +/* + * Cavium Networks architecture timex specifications + * + * Copyright 2003 ARM Limited + * Copyright 2008 Cavium Networks + * + * This file is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License, Version 2, as + * published by the Free Software Foundation. + */ + +#define CLOCK_TICK_RATE (50000000 / 16) diff --git a/arch/arm/mach-cns3xxx/include/mach/uncompress.h b/arch/arm/mach-cns3xxx/include/mach/uncompress.h new file mode 100644 index 0000000..de8ead9 --- /dev/null +++ b/arch/arm/mach-cns3xxx/include/mach/uncompress.h @@ -0,0 +1,55 @@ +/* + * Copyright 2003 ARM Limited + * Copyright 2008 Cavium Networks + * + * This file is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License, Version 2, as + * published by the Free Software Foundation. + */ + +#include <asm/mach-types.h> +#include <mach/hardware.h> +#include <mach/cns3xxx.h> + +#define AMBA_UART_DR(base) (*(volatile unsigned char *)((base) + 0x00)) +#define AMBA_UART_LCRH(base) (*(volatile unsigned char *)((base) + 0x2c)) +#define AMBA_UART_CR(base) (*(volatile unsigned char *)((base) + 0x30)) +#define AMBA_UART_FR(base) (*(volatile unsigned char *)((base) + 0x18)) + +/* + * Return the UART base address + */ +static inline unsigned long get_uart_base(void) +{ + if (machine_is_cns3420vb()) + return CNS3XXX_UART0_BASE; + else + return 0; +} + +/* + * This does not append a newline + */ +static inline void putc(int c) +{ + unsigned long base = get_uart_base(); + + while (AMBA_UART_FR(base) & (1 << 5)) + barrier(); + + AMBA_UART_DR(base) = c; +} + +static inline void flush(void) +{ + unsigned long base = get_uart_base(); + + while (AMBA_UART_FR(base) & (1 << 3)) + barrier(); +} + +/* + * nothing to do + */ +#define arch_decomp_setup() +#define arch_decomp_wdog() diff --git a/arch/arm/mach-cns3xxx/include/mach/vmalloc.h b/arch/arm/mach-cns3xxx/include/mach/vmalloc.h new file mode 100644 index 0000000..4d381ec --- /dev/null +++ b/arch/arm/mach-cns3xxx/include/mach/vmalloc.h @@ -0,0 +1,11 @@ +/* + * Copyright 2000 Russell King. + * Copyright 2003 ARM Limited + * Copyright 2008 Cavium Networks + * + * This file is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License, Version 2, as + * published by the Free Software Foundation. + */ + +#define VMALLOC_END 0xd8000000 diff --git a/arch/arm/mach-cns3xxx/pm.c b/arch/arm/mach-cns3xxx/pm.c new file mode 100644 index 0000000..725e1a4 --- /dev/null +++ b/arch/arm/mach-cns3xxx/pm.c @@ -0,0 +1,86 @@ +/* + * Copyright 2008 Cavium Networks + * + * This file is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License, Version 2, as + * published by the Free Software Foundation. + */ + +#include <linux/delay.h> +#include <mach/system.h> +#include <mach/cns3xxx.h> + +void cns3xxx_pwr_clk_en(unsigned int block) +{ + PM_CLK_GATE_REG |= (block & PM_CLK_GATE_REG_MASK); +} + +void cns3xxx_pwr_power_up(unsigned int block) +{ + PM_PLL_HM_PD_CTRL_REG &= ~(block & CNS3XXX_PWR_PLL_ALL); + + /* Wait for 300us for the PLL output clock locked. */ + udelay(300); +}; + +void cns3xxx_pwr_power_down(unsigned int block) +{ + /* write '1' to power down */ + PM_PLL_HM_PD_CTRL_REG |= (block & CNS3XXX_PWR_PLL_ALL); +}; + +static void cns3xxx_pwr_soft_rst_force(unsigned int block) +{ + /* + * bit 0, 28, 29 => program low to reset, + * the other else program low and then high + */ + if (block & 0x30000001) { + PM_SOFT_RST_REG &= ~(block & PM_SOFT_RST_REG_MASK); + } else { + PM_SOFT_RST_REG &= ~(block & PM_SOFT_RST_REG_MASK); + PM_SOFT_RST_REG |= (block & PM_SOFT_RST_REG_MASK); + } +} + +void cns3xxx_pwr_soft_rst(unsigned int block) +{ + static unsigned int soft_reset; + + if (soft_reset & block) { + /* SPI/I2C/GPIO use the same block, reset once. */ + return; + } else { + soft_reset |= block; + } + cns3xxx_pwr_soft_rst_force(block); +} + +void arch_reset(char mode, const char *cmd) +{ + /* + * To reset, we hit the on-board reset register + * in the system FPGA. + */ + cns3xxx_pwr_soft_rst(CNS3XXX_PWR_SOFTWARE_RST(GLOBAL)); +} + +/* + * cns3xxx_cpu_clock - return CPU/L2 clock + * aclk: cpu clock/2 + * hclk: cpu clock/4 + * pclk: cpu clock/8 + */ +int cns3xxx_cpu_clock(void) +{ + int cpu; + int cpu_sel; + int div_sel; + + cpu_sel = (PM_CLK_CTRL_REG >> PM_CLK_CTRL_REG_OFFSET_PLL_CPU_SEL) & 0xf; + div_sel = (PM_CLK_CTRL_REG >> PM_CLK_CTRL_REG_OFFSET_CPU_CLK_DIV) & 0x3; + + cpu = (300 + ((cpu_sel / 3) * 100) + ((cpu_sel % 3) * 33)) >> div_sel; + + return cpu; +} -- 1.7.0.3 ^ permalink raw reply related [flat|nested] 7+ messages in thread
* [PATCH 1/3] ARM: cns3xxx: Add basic support for Cavium Networks CNS3xxx processors 2010-03-30 19:02 ` [PATCH 1/3] ARM: cns3xxx: Add basic support for Cavium Networks CNS3xxx processors Anton Vorontsov @ 2010-04-14 15:40 ` Russell King - ARM Linux 2010-04-14 16:15 ` [PATCH v4 " Anton Vorontsov 0 siblings, 1 reply; 7+ messages in thread From: Russell King - ARM Linux @ 2010-04-14 15:40 UTC (permalink / raw) To: linux-arm-kernel On Tue, Mar 30, 2010 at 11:02:45PM +0400, Anton Vorontsov wrote: > diff --git a/arch/arm/mach-cns3xxx/include/mach/io.h b/arch/arm/mach-cns3xxx/include/mach/io.h > new file mode 100644 > index 0000000..b4ff09a > --- /dev/null > +++ b/arch/arm/mach-cns3xxx/include/mach/io.h > @@ -0,0 +1,22 @@ > +/* > + * Copyright 2008 Cavium Networks > + * Copyright 2003 ARM Limited > + * > + * This file is free software; you can redistribute it and/or modify > + * it under the terms of the GNU General Public License, Version 2, as > + * published by the Free Software Foundation. > + */ > +#ifndef __MACH_IO_H > +#define __MACH_IO_H > + > +#define IO_SPACE_LIMIT 0xffffffff > + > +static inline void __iomem *__io(unsigned long addr) > +{ > + return (void __iomem *)addr; > +} I'm not sure why you define a static inline function for __io here - it's overriden by the following macro: > + > +#define __io(a) __typesafe_io(a) > +#define __mem_pci(a) (a) ^ permalink raw reply [flat|nested] 7+ messages in thread
* [PATCH v4 1/3] ARM: cns3xxx: Add basic support for Cavium Networks CNS3xxx processors 2010-04-14 15:40 ` Russell King - ARM Linux @ 2010-04-14 16:15 ` Anton Vorontsov 0 siblings, 0 replies; 7+ messages in thread From: Anton Vorontsov @ 2010-04-14 16:15 UTC (permalink / raw) To: linux-arm-kernel On Wed, Apr 14, 2010 at 04:40:37PM +0100, Russell King - ARM Linux wrote: [...] > > +static inline void __iomem *__io(unsigned long addr) > > +{ > > + return (void __iomem *)addr; > > +} > > I'm not sure why you define a static inline function for __io here - it's > overriden by the following macro: > > > +#define __io(a) __typesafe_io(a) Ugh. I switched that __io() define to the __typesafe_io(), but forgot to remove the __io function. Thanks for noticing! Updated patch below. - - - - ARM: cns3xxx: Add basic support for Cavium Networks CNS3xxx processors This patch adds very basic support for ECONA CNS3xxx ARM11 MPcore (ARMv6) dual-core processors. Note that SMP is not yet supported, as well as many peripheral devices. Support for these features will be added later. Signed-off-by: Anton Vorontsov <avorontsov@mvista.com> --- MAINTAINERS | 6 + arch/arm/Kconfig | 11 + arch/arm/Makefile | 1 + arch/arm/mach-cns3xxx/Kconfig | 4 + arch/arm/mach-cns3xxx/Makefile | 1 + arch/arm/mach-cns3xxx/Makefile.boot | 3 + arch/arm/mach-cns3xxx/core.c | 249 +++++++++ arch/arm/mach-cns3xxx/core.h | 23 + arch/arm/mach-cns3xxx/include/mach/cns3xxx.h | 635 ++++++++++++++++++++++ arch/arm/mach-cns3xxx/include/mach/debug-macro.S | 21 + arch/arm/mach-cns3xxx/include/mach/entry-macro.S | 82 +++ arch/arm/mach-cns3xxx/include/mach/hardware.h | 22 + arch/arm/mach-cns3xxx/include/mach/io.h | 17 + arch/arm/mach-cns3xxx/include/mach/irqs.h | 24 + arch/arm/mach-cns3xxx/include/mach/memory.h | 26 + arch/arm/mach-cns3xxx/include/mach/system.h | 29 + arch/arm/mach-cns3xxx/include/mach/timex.h | 12 + arch/arm/mach-cns3xxx/include/mach/uncompress.h | 55 ++ arch/arm/mach-cns3xxx/include/mach/vmalloc.h | 11 + arch/arm/mach-cns3xxx/pm.c | 86 +++ 20 files changed, 1318 insertions(+), 0 deletions(-) create mode 100644 arch/arm/mach-cns3xxx/Kconfig create mode 100644 arch/arm/mach-cns3xxx/Makefile create mode 100644 arch/arm/mach-cns3xxx/Makefile.boot create mode 100644 arch/arm/mach-cns3xxx/core.c create mode 100644 arch/arm/mach-cns3xxx/core.h create mode 100644 arch/arm/mach-cns3xxx/include/mach/cns3xxx.h create mode 100644 arch/arm/mach-cns3xxx/include/mach/debug-macro.S create mode 100644 arch/arm/mach-cns3xxx/include/mach/entry-macro.S create mode 100644 arch/arm/mach-cns3xxx/include/mach/hardware.h create mode 100644 arch/arm/mach-cns3xxx/include/mach/io.h create mode 100644 arch/arm/mach-cns3xxx/include/mach/irqs.h create mode 100644 arch/arm/mach-cns3xxx/include/mach/memory.h create mode 100644 arch/arm/mach-cns3xxx/include/mach/system.h create mode 100644 arch/arm/mach-cns3xxx/include/mach/timex.h create mode 100644 arch/arm/mach-cns3xxx/include/mach/uncompress.h create mode 100644 arch/arm/mach-cns3xxx/include/mach/vmalloc.h create mode 100644 arch/arm/mach-cns3xxx/pm.c diff --git a/MAINTAINERS b/MAINTAINERS index 449d444..93ebdf8 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -586,6 +586,12 @@ F: drivers/mtd/nand/bcm_umi_bch.c F: drivers/mtd/nand/bcm_umi_hamming.c F: drivers/mtd/nand/nand_bcm_umi.h +ARM/CAVIUM NETWORKS CNS3XXX MACHINE SUPPORT +M: Anton Vorontsov <avorontsov@mvista.com> +S: Maintained +F: arch/arm/mach-cns3xxx/ +T: git git://git.infradead.org/users/cbou/linux-cns3xxx.git + ARM/CIRRUS LOGIC EP93XX ARM ARCHITECTURE M: Hartley Sweeten <hsweeten@visionengravers.com> M: Ryan Mallon <ryan@bluewatersys.com> diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig index c5408bf..d779e25 100644 --- a/arch/arm/Kconfig +++ b/arch/arm/Kconfig @@ -296,6 +296,15 @@ config ARCH_CLPS711X help Support for Cirrus Logic 711x/721x based boards. +config ARCH_CNS3XXX + bool "Cavium Networks CNS3XXX family" + select CPU_V6 + select GENERIC_TIME + select GENERIC_CLOCKEVENTS + select ARM_GIC + help + Support for Cavium Networks CNS3XXX platform. + config ARCH_GEMINI bool "Cortina Systems Gemini" select CPU_FA526 @@ -816,6 +825,8 @@ source "arch/arm/mach-bcmring/Kconfig" source "arch/arm/mach-clps711x/Kconfig" +source "arch/arm/mach-cns3xxx/Kconfig" + source "arch/arm/mach-davinci/Kconfig" source "arch/arm/mach-dove/Kconfig" diff --git a/arch/arm/Makefile b/arch/arm/Makefile index ed820e7..3e312ec 100644 --- a/arch/arm/Makefile +++ b/arch/arm/Makefile @@ -121,6 +121,7 @@ machine-$(CONFIG_ARCH_AAEC2000) := aaec2000 machine-$(CONFIG_ARCH_AT91) := at91 machine-$(CONFIG_ARCH_BCMRING) := bcmring machine-$(CONFIG_ARCH_CLPS711X) := clps711x +machine-$(CONFIG_ARCH_CNS3XXX) := cns3xxx machine-$(CONFIG_ARCH_DAVINCI) := davinci machine-$(CONFIG_ARCH_DOVE) := dove machine-$(CONFIG_ARCH_EBSA110) := ebsa110 diff --git a/arch/arm/mach-cns3xxx/Kconfig b/arch/arm/mach-cns3xxx/Kconfig new file mode 100644 index 0000000..20284cd --- /dev/null +++ b/arch/arm/mach-cns3xxx/Kconfig @@ -0,0 +1,4 @@ +menu "CNS3XXX platform type" + depends on ARCH_CNS3XXX + +endmenu diff --git a/arch/arm/mach-cns3xxx/Makefile b/arch/arm/mach-cns3xxx/Makefile new file mode 100644 index 0000000..e5e76dd --- /dev/null +++ b/arch/arm/mach-cns3xxx/Makefile @@ -0,0 +1 @@ +obj-$(CONFIG_ARCH_CNS3XXX) += core.o pm.o diff --git a/arch/arm/mach-cns3xxx/Makefile.boot b/arch/arm/mach-cns3xxx/Makefile.boot new file mode 100644 index 0000000..7770128 --- /dev/null +++ b/arch/arm/mach-cns3xxx/Makefile.boot @@ -0,0 +1,3 @@ + zreladdr-y := 0x00008000 +params_phys-y := 0x00000100 +initrd_phys-y := 0x00C00000 diff --git a/arch/arm/mach-cns3xxx/core.c b/arch/arm/mach-cns3xxx/core.c new file mode 100644 index 0000000..9ca4d58 --- /dev/null +++ b/arch/arm/mach-cns3xxx/core.c @@ -0,0 +1,249 @@ +/* + * Copyright 1999 - 2003 ARM Limited + * Copyright 2000 Deep Blue Solutions Ltd + * Copyright 2008 Cavium Networks + * + * This file is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License, Version 2, as + * published by the Free Software Foundation. + */ + +#include <linux/init.h> +#include <linux/interrupt.h> +#include <linux/clockchips.h> +#include <linux/io.h> +#include <asm/mach/map.h> +#include <asm/mach/time.h> +#include <asm/mach/irq.h> +#include <asm/hardware/gic.h> +#include <mach/cns3xxx.h> +#include "core.h" + +static struct map_desc cns3xxx_io_desc[] __initdata = { + { + .virtual = CNS3XXX_TC11MP_TWD_BASE_VIRT, + .pfn = __phys_to_pfn(CNS3XXX_TC11MP_TWD_BASE), + .length = SZ_4K, + .type = MT_DEVICE, + }, { + .virtual = CNS3XXX_TC11MP_GIC_CPU_BASE_VIRT, + .pfn = __phys_to_pfn(CNS3XXX_TC11MP_GIC_CPU_BASE), + .length = SZ_4K, + .type = MT_DEVICE, + }, { + .virtual = CNS3XXX_TC11MP_GIC_DIST_BASE_VIRT, + .pfn = __phys_to_pfn(CNS3XXX_TC11MP_GIC_DIST_BASE), + .length = SZ_4K, + .type = MT_DEVICE, + }, { + .virtual = CNS3XXX_TIMER1_2_3_BASE_VIRT, + .pfn = __phys_to_pfn(CNS3XXX_TIMER1_2_3_BASE), + .length = SZ_4K, + .type = MT_DEVICE, + }, { + .virtual = CNS3XXX_GPIOA_BASE_VIRT, + .pfn = __phys_to_pfn(CNS3XXX_GPIOA_BASE), + .length = SZ_4K, + .type = MT_DEVICE, + }, { + .virtual = CNS3XXX_GPIOB_BASE_VIRT, + .pfn = __phys_to_pfn(CNS3XXX_GPIOB_BASE), + .length = SZ_4K, + .type = MT_DEVICE, + }, { + .virtual = CNS3XXX_MISC_BASE_VIRT, + .pfn = __phys_to_pfn(CNS3XXX_MISC_BASE), + .length = SZ_4K, + .type = MT_DEVICE, + }, { + .virtual = CNS3XXX_PM_BASE_VIRT, + .pfn = __phys_to_pfn(CNS3XXX_PM_BASE), + .length = SZ_4K, + .type = MT_DEVICE, + }, +}; + +void __init cns3xxx_map_io(void) +{ + iotable_init(cns3xxx_io_desc, ARRAY_SIZE(cns3xxx_io_desc)); +} + +/* used by entry-macro.S */ +void __iomem *gic_cpu_base_addr; + +void __init cns3xxx_init_irq(void) +{ + gic_cpu_base_addr = __io(CNS3XXX_TC11MP_GIC_CPU_BASE_VIRT); + gic_dist_init(0, __io(CNS3XXX_TC11MP_GIC_DIST_BASE_VIRT), 29); + gic_cpu_init(0, gic_cpu_base_addr); +} + +void cns3xxx_power_off(void) +{ + u32 __iomem *pm_base = __io(CNS3XXX_PM_BASE_VIRT); + u32 clkctrl; + + printk(KERN_INFO "powering system down...\n"); + + clkctrl = readl(pm_base + PM_SYS_CLK_CTRL_OFFSET); + clkctrl &= 0xfffff1ff; + clkctrl |= (0x5 << 9); /* Hibernate */ + writel(clkctrl, pm_base + PM_SYS_CLK_CTRL_OFFSET); + +} + +/* + * Timer + */ +static void __iomem *cns3xxx_tmr1; + +static void cns3xxx_timer_set_mode(enum clock_event_mode mode, + struct clock_event_device *clk) +{ + unsigned long ctrl = readl(cns3xxx_tmr1 + TIMER1_2_CONTROL_OFFSET); + int pclk = cns3xxx_cpu_clock() / 8; + int reload; + + switch (mode) { + case CLOCK_EVT_MODE_PERIODIC: + reload = pclk * 20 / (3 * HZ) * 0x25000; + writel(reload, cns3xxx_tmr1 + TIMER1_AUTO_RELOAD_OFFSET); + ctrl |= (1 << 0) | (1 << 2) | (1 << 9); + break; + case CLOCK_EVT_MODE_ONESHOT: + /* period set, and timer enabled in 'next_event' hook */ + ctrl |= (1 << 2) | (1 << 9); + break; + case CLOCK_EVT_MODE_UNUSED: + case CLOCK_EVT_MODE_SHUTDOWN: + default: + ctrl = 0; + } + + writel(ctrl, cns3xxx_tmr1 + TIMER1_2_CONTROL_OFFSET); +} + +static int cns3xxx_timer_set_next_event(unsigned long evt, + struct clock_event_device *unused) +{ + unsigned long ctrl = readl(cns3xxx_tmr1 + TIMER1_2_CONTROL_OFFSET); + + writel(evt, cns3xxx_tmr1 + TIMER1_AUTO_RELOAD_OFFSET); + writel(ctrl | (1 << 0), cns3xxx_tmr1 + TIMER1_2_CONTROL_OFFSET); + + return 0; +} + +static struct clock_event_device cns3xxx_tmr1_clockevent = { + .name = "cns3xxx timer1", + .shift = 8, + .features = CLOCK_EVT_FEAT_PERIODIC | CLOCK_EVT_FEAT_ONESHOT, + .set_mode = cns3xxx_timer_set_mode, + .set_next_event = cns3xxx_timer_set_next_event, + .rating = 350, + .cpumask = cpu_all_mask, +}; + +static void __init cns3xxx_clockevents_init(unsigned int timer_irq) +{ + cns3xxx_tmr1_clockevent.irq = timer_irq; + cns3xxx_tmr1_clockevent.mult = + div_sc((cns3xxx_cpu_clock() >> 3) * 1000000, NSEC_PER_SEC, + cns3xxx_tmr1_clockevent.shift); + cns3xxx_tmr1_clockevent.max_delta_ns = + clockevent_delta2ns(0xffffffff, &cns3xxx_tmr1_clockevent); + cns3xxx_tmr1_clockevent.min_delta_ns = + clockevent_delta2ns(0xf, &cns3xxx_tmr1_clockevent); + + clockevents_register_device(&cns3xxx_tmr1_clockevent); +} + +/* + * IRQ handler for the timer + */ +static irqreturn_t cns3xxx_timer_interrupt(int irq, void *dev_id) +{ + struct clock_event_device *evt = &cns3xxx_tmr1_clockevent; + u32 __iomem *stat = cns3xxx_tmr1 + TIMER1_2_INTERRUPT_STATUS_OFFSET; + u32 val; + + /* Clear the interrupt */ + val = readl(stat); + writel(val & ~(1 << 2), stat); + + evt->event_handler(evt); + + return IRQ_HANDLED; +} + +static struct irqaction cns3xxx_timer_irq = { + .name = "timer", + .flags = IRQF_DISABLED | IRQF_TIMER | IRQF_IRQPOLL, + .handler = cns3xxx_timer_interrupt, +}; + +/* + * Set up the clock source and clock events devices + */ +static void __init __cns3xxx_timer_init(unsigned int timer_irq) +{ + u32 val; + u32 irq_mask; + + /* + * Initialise to a known state (all timers off) + */ + + /* disable timer1 and timer2 */ + writel(0, cns3xxx_tmr1 + TIMER1_2_CONTROL_OFFSET); + /* stop free running timer3 */ + writel(0, cns3xxx_tmr1 + TIMER_FREERUN_CONTROL_OFFSET); + + /* timer1 */ + writel(0x5C800, cns3xxx_tmr1 + TIMER1_COUNTER_OFFSET); + writel(0x5C800, cns3xxx_tmr1 + TIMER1_AUTO_RELOAD_OFFSET); + + writel(0, cns3xxx_tmr1 + TIMER1_MATCH_V1_OFFSET); + writel(0, cns3xxx_tmr1 + TIMER1_MATCH_V2_OFFSET); + + /* mask irq, non-mask timer1 overflow */ + irq_mask = readl(cns3xxx_tmr1 + TIMER1_2_INTERRUPT_MASK_OFFSET); + irq_mask &= ~(1 << 2); + irq_mask |= 0x03; + writel(irq_mask, cns3xxx_tmr1 + TIMER1_2_INTERRUPT_MASK_OFFSET); + + /* down counter */ + val = readl(cns3xxx_tmr1 + TIMER1_2_CONTROL_OFFSET); + val |= (1 << 9); + writel(val, cns3xxx_tmr1 + TIMER1_2_CONTROL_OFFSET); + + /* timer2 */ + writel(0, cns3xxx_tmr1 + TIMER2_MATCH_V1_OFFSET); + writel(0, cns3xxx_tmr1 + TIMER2_MATCH_V2_OFFSET); + + /* mask irq */ + irq_mask = readl(cns3xxx_tmr1 + TIMER1_2_INTERRUPT_MASK_OFFSET); + irq_mask |= ((1 << 3) | (1 << 4) | (1 << 5)); + writel(irq_mask, cns3xxx_tmr1 + TIMER1_2_INTERRUPT_MASK_OFFSET); + + /* down counter */ + val = readl(cns3xxx_tmr1 + TIMER1_2_CONTROL_OFFSET); + val |= (1 << 10); + writel(val, cns3xxx_tmr1 + TIMER1_2_CONTROL_OFFSET); + + /* Make irqs happen for the system timer */ + setup_irq(timer_irq, &cns3xxx_timer_irq); + + cns3xxx_clockevents_init(timer_irq); +} + +static void __init cns3xxx_timer_init(void) +{ + cns3xxx_tmr1 = __io(CNS3XXX_TIMER1_2_3_BASE_VIRT); + + __cns3xxx_timer_init(IRQ_CNS3XXX_TIMER0); +} + +struct sys_timer cns3xxx_timer = { + .init = cns3xxx_timer_init, +}; diff --git a/arch/arm/mach-cns3xxx/core.h b/arch/arm/mach-cns3xxx/core.h new file mode 100644 index 0000000..6b33ec1 --- /dev/null +++ b/arch/arm/mach-cns3xxx/core.h @@ -0,0 +1,23 @@ +/* + * Copyright 2000 Deep Blue Solutions Ltd + * Copyright 2004 ARM Limited + * Copyright 2008 Cavium Networks + * + * This file is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License, Version 2, as + * published by the Free Software Foundation. + */ + +#ifndef __CNS3XXX_CORE_H +#define __CNS3XXX_CORE_H + +extern void __iomem *gic_cpu_base_addr; +extern struct sys_timer cns3xxx_timer; + +void __init cns3xxx_map_io(void); +void __init cns3xxx_init_irq(void); +void cns3xxx_power_off(void); +void cns3xxx_pwr_power_up(unsigned int block); +void cns3xxx_pwr_power_down(unsigned int block); + +#endif /* __CNS3XXX_CORE_H */ diff --git a/arch/arm/mach-cns3xxx/include/mach/cns3xxx.h b/arch/arm/mach-cns3xxx/include/mach/cns3xxx.h new file mode 100644 index 0000000..8a2f5a2 --- /dev/null +++ b/arch/arm/mach-cns3xxx/include/mach/cns3xxx.h @@ -0,0 +1,635 @@ +/* + * Copyright 2008 Cavium Networks + * + * This file is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License, Version 2, as + * published by the Free Software Foundation. + */ + +#ifndef __MACH_BOARD_CNS3XXXH +#define __MACH_BOARD_CNS3XXXH + +/* + * Memory map + */ +#define CNS3XXX_FLASH_BASE 0x10000000 /* Flash/SRAM Memory Bank 0 */ +#define CNS3XXX_FLASH_SIZE SZ_256M + +#define CNS3XXX_DDR2SDRAM_BASE 0x20000000 /* DDR2 SDRAM Memory */ + +#define CNS3XXX_SPI_FLASH_BASE 0x60000000 /* SPI Serial Flash Memory */ + +#define CNS3XXX_SWITCH_BASE 0x70000000 /* Switch and HNAT Control */ +#define CNS3XXX_SWITCH_BASE_VIRT 0xFFF00000 + +#define CNS3XXX_PPE_BASE 0x70001000 /* HANT */ +#define CNS3XXX_PPE_BASE_VIRT 0xFFF50000 + +#define CNS3XXX_EMBEDDED_SRAM_BASE 0x70002000 /* HANT Embedded SRAM */ +#define CNS3XXX_EMBEDDED_SRAM_BASE_VIRT 0xFFF60000 + +#define CNS3XXX_SSP_BASE 0x71000000 /* Synchronous Serial Port - SPI/PCM/I2C */ +#define CNS3XXX_SSP_BASE_VIRT 0xFFF01000 + +#define CNS3XXX_DMC_BASE 0x72000000 /* DMC Control (DDR2 SDRAM) */ +#define CNS3XXX_DMC_BASE_VIRT 0xFFF02000 + +#define CNS3XXX_SMC_BASE 0x73000000 /* SMC Control */ +#define CNS3XXX_SMC_BASE_VIRT 0xFFF03000 + +#define SMC_MEMC_STATUS_OFFSET 0x000 +#define SMC_MEMIF_CFG_OFFSET 0x004 +#define SMC_MEMC_CFG_SET_OFFSET 0x008 +#define SMC_MEMC_CFG_CLR_OFFSET 0x00C +#define SMC_DIRECT_CMD_OFFSET 0x010 +#define SMC_SET_CYCLES_OFFSET 0x014 +#define SMC_SET_OPMODE_OFFSET 0x018 +#define SMC_REFRESH_PERIOD_0_OFFSET 0x020 +#define SMC_REFRESH_PERIOD_1_OFFSET 0x024 +#define SMC_SRAM_CYCLES0_0_OFFSET 0x100 +#define SMC_NAND_CYCLES0_0_OFFSET 0x100 +#define SMC_OPMODE0_0_OFFSET 0x104 +#define SMC_SRAM_CYCLES0_1_OFFSET 0x120 +#define SMC_NAND_CYCLES0_1_OFFSET 0x120 +#define SMC_OPMODE0_1_OFFSET 0x124 +#define SMC_USER_STATUS_OFFSET 0x200 +#define SMC_USER_CONFIG_OFFSET 0x204 +#define SMC_ECC_STATUS_OFFSET 0x300 +#define SMC_ECC_MEMCFG_OFFSET 0x304 +#define SMC_ECC_MEMCOMMAND1_OFFSET 0x308 +#define SMC_ECC_MEMCOMMAND2_OFFSET 0x30C +#define SMC_ECC_ADDR0_OFFSET 0x310 +#define SMC_ECC_ADDR1_OFFSET 0x314 +#define SMC_ECC_VALUE0_OFFSET 0x318 +#define SMC_ECC_VALUE1_OFFSET 0x31C +#define SMC_ECC_VALUE2_OFFSET 0x320 +#define SMC_ECC_VALUE3_OFFSET 0x324 +#define SMC_PERIPH_ID_0_OFFSET 0xFE0 +#define SMC_PERIPH_ID_1_OFFSET 0xFE4 +#define SMC_PERIPH_ID_2_OFFSET 0xFE8 +#define SMC_PERIPH_ID_3_OFFSET 0xFEC +#define SMC_PCELL_ID_0_OFFSET 0xFF0 +#define SMC_PCELL_ID_1_OFFSET 0xFF4 +#define SMC_PCELL_ID_2_OFFSET 0xFF8 +#define SMC_PCELL_ID_3_OFFSET 0xFFC + +#define CNS3XXX_GPIOA_BASE 0x74000000 /* GPIO port A */ +#define CNS3XXX_GPIOA_BASE_VIRT 0xFFF04000 + +#define CNS3XXX_GPIOB_BASE 0x74800000 /* GPIO port B */ +#define CNS3XXX_GPIOB_BASE_VIRT 0xFFF05000 + +#define CNS3XXX_RTC_BASE 0x75000000 /* Real Time Clock */ +#define CNS3XXX_RTC_BASE_VIRT 0xFFF06000 + +#define RTC_SEC_OFFSET 0x00 +#define RTC_MIN_OFFSET 0x04 +#define RTC_HOUR_OFFSET 0x08 +#define RTC_DAY_OFFSET 0x0C +#define RTC_SEC_ALM_OFFSET 0x10 +#define RTC_MIN_ALM_OFFSET 0x14 +#define RTC_HOUR_ALM_OFFSET 0x18 +#define RTC_REC_OFFSET 0x1C +#define RTC_CTRL_OFFSET 0x20 +#define RTC_INTR_STS_OFFSET 0x34 + +#define CNS3XXX_MISC_BASE 0x76000000 /* Misc Control */ +#define CNS3XXX_MISC_BASE_VIRT 0xFFF07000 /* Misc Control */ + +#define CNS3XXX_PM_BASE 0x77000000 /* Power Management Control */ +#define CNS3XXX_PM_BASE_VIRT 0xFFF08000 + +#define PM_CLK_GATE_OFFSET 0x00 +#define PM_SOFT_RST_OFFSET 0x04 +#define PM_HS_CFG_OFFSET 0x08 +#define PM_CACTIVE_STA_OFFSET 0x0C +#define PM_PWR_STA_OFFSET 0x10 +#define PM_SYS_CLK_CTRL_OFFSET 0x14 +#define PM_PLL_LCD_I2S_CTRL_OFFSET 0x18 +#define PM_PLL_HM_PD_OFFSET 0x1C + +#define CNS3XXX_UART0_BASE 0x78000000 /* UART 0 */ +#define CNS3XXX_UART0_BASE_VIRT 0xFFF09000 + +#define CNS3XXX_UART1_BASE 0x78400000 /* UART 1 */ +#define CNS3XXX_UART1_BASE_VIRT 0xFFF0A000 + +#define CNS3XXX_UART2_BASE 0x78800000 /* UART 2 */ +#define CNS3XXX_UART2_BASE_VIRT 0xFFF0B000 + +#define CNS3XXX_DMAC_BASE 0x79000000 /* Generic DMA Control */ +#define CNS3XXX_DMAC_BASE_VIRT 0xFFF0D000 + +#define CNS3XXX_CORESIGHT_BASE 0x7A000000 /* CoreSight */ +#define CNS3XXX_CORESIGHT_BASE_VIRT 0xFFF0E000 + +#define CNS3XXX_CRYPTO_BASE 0x7B000000 /* Crypto */ +#define CNS3XXX_CRYPTO_BASE_VIRT 0xFFF0F000 + +#define CNS3XXX_I2S_BASE 0x7C000000 /* I2S */ +#define CNS3XXX_I2S_BASE_VIRT 0xFFF10000 + +#define CNS3XXX_TIMER1_2_3_BASE 0x7C800000 /* Timer */ +#define CNS3XXX_TIMER1_2_3_BASE_VIRT 0xFFF10800 + +#define TIMER1_COUNTER_OFFSET 0x00 +#define TIMER1_AUTO_RELOAD_OFFSET 0x04 +#define TIMER1_MATCH_V1_OFFSET 0x08 +#define TIMER1_MATCH_V2_OFFSET 0x0C + +#define TIMER2_COUNTER_OFFSET 0x10 +#define TIMER2_AUTO_RELOAD_OFFSET 0x14 +#define TIMER2_MATCH_V1_OFFSET 0x18 +#define TIMER2_MATCH_V2_OFFSET 0x1C + +#define TIMER1_2_CONTROL_OFFSET 0x30 +#define TIMER1_2_INTERRUPT_STATUS_OFFSET 0x34 +#define TIMER1_2_INTERRUPT_MASK_OFFSET 0x38 + +#define TIMER_FREERUN_OFFSET 0x40 +#define TIMER_FREERUN_CONTROL_OFFSET 0x44 + +#define CNS3XXX_HCIE_BASE 0x7D000000 /* HCIE Control */ +#define CNS3XXX_HCIE_BASE_VIRT 0xFFF30000 + +#define CNS3XXX_RAID_BASE 0x7E000000 /* RAID Control */ +#define CNS3XXX_RAID_BASE_VIRT 0xFFF12000 + +#define CNS3XXX_AXI_IXC_BASE 0x7F000000 /* AXI IXC */ +#define CNS3XXX_AXI_IXC_BASE_VIRT 0xFFF13000 + +#define CNS3XXX_CLCD_BASE 0x80000000 /* LCD Control */ +#define CNS3XXX_CLCD_BASE_VIRT 0xFFF14000 + +#define CNS3XXX_USBOTG_BASE 0x81000000 /* USB OTG Control */ +#define CNS3XXX_USBOTG_BASE_VIRT 0xFFF15000 + +#define CNS3XXX_USB_BASE 0x82000000 /* USB Host Control */ +#define CNS3XXX_USB_BASE_VIRT 0xFFF16000 + +#define CNS3XXX_SATA2_BASE 0x83000000 /* SATA */ +#define CNS3XXX_SATA2_SIZE SZ_16M +#define CNS3XXX_SATA2_BASE_VIRT 0xFFF17000 + +#define CNS3XXX_CAMERA_BASE 0x84000000 /* Camera Interface */ +#define CNS3XXX_CAMERA_BASE_VIRT 0xFFF18000 + +#define CNS3XXX_SDIO_BASE 0x85000000 /* SDIO */ +#define CNS3XXX_SDIO_BASE_VIRT 0xFFF19000 + +#define CNS3XXX_I2S_TDM_BASE 0x86000000 /* I2S TDM */ +#define CNS3XXX_I2S_TDM_BASE_VIRT 0xFFF1A000 + +#define CNS3XXX_2DG_BASE 0x87000000 /* 2D Graphic Control */ +#define CNS3XXX_2DG_BASE_VIRT 0xFFF1B000 + +#define CNS3XXX_USB_OHCI_BASE 0x88000000 /* USB OHCI */ +#define CNS3XXX_USB_OHCI_BASE_VIRT 0xFFF1C000 + +#define CNS3XXX_L2C_BASE 0x92000000 /* L2 Cache Control */ +#define CNS3XXX_L2C_BASE_VIRT 0xFFF27000 + +#define CNS3XXX_PCIE0_MEM_BASE 0xA0000000 /* PCIe Port 0 IO/Memory Space */ +#define CNS3XXX_PCIE0_MEM_BASE_VIRT 0xE0000000 + +#define CNS3XXX_PCIE0_HOST_BASE 0xAB000000 /* PCIe Port 0 RC Base */ +#define CNS3XXX_PCIE0_HOST_BASE_VIRT 0xE1000000 + +#define CNS3XXX_PCIE0_IO_BASE 0xAC000000 /* PCIe Port 0 */ +#define CNS3XXX_PCIE0_IO_BASE_VIRT 0xE2000000 + +#define CNS3XXX_PCIE0_CFG0_BASE 0xAD000000 /* PCIe Port 0 CFG Type 0 */ +#define CNS3XXX_PCIE0_CFG0_BASE_VIRT 0xE3000000 + +#define CNS3XXX_PCIE0_CFG1_BASE 0xAE000000 /* PCIe Port 0 CFG Type 1 */ +#define CNS3XXX_PCIE0_CFG1_BASE_VIRT 0xE4000000 + +#define CNS3XXX_PCIE0_MSG_BASE 0xAF000000 /* PCIe Port 0 Message Space */ +#define CNS3XXX_PCIE0_MSG_BASE_VIRT 0xE5000000 + +#define CNS3XXX_PCIE1_MEM_BASE 0xB0000000 /* PCIe Port 1 IO/Memory Space */ +#define CNS3XXX_PCIE1_MEM_BASE_VIRT 0xE8000000 + +#define CNS3XXX_PCIE1_HOST_BASE 0xBB000000 /* PCIe Port 1 RC Base */ +#define CNS3XXX_PCIE1_HOST_BASE_VIRT 0xE9000000 + +#define CNS3XXX_PCIE1_IO_BASE 0xBC000000 /* PCIe Port 1 */ +#define CNS3XXX_PCIE1_IO_BASE_VIRT 0xEA000000 + +#define CNS3XXX_PCIE1_CFG0_BASE 0xBD000000 /* PCIe Port 1 CFG Type 0 */ +#define CNS3XXX_PCIE1_CFG0_BASE_VIRT 0xEB000000 + +#define CNS3XXX_PCIE1_CFG1_BASE 0xBE000000 /* PCIe Port 1 CFG Type 1 */ +#define CNS3XXX_PCIE1_CFG1_BASE_VIRT 0xEC000000 + +#define CNS3XXX_PCIE1_MSG_BASE 0xBF000000 /* PCIe Port 1 Message Space */ +#define CNS3XXX_PCIE1_MSG_BASE_VIRT 0xED000000 + +/* + * Testchip peripheral and fpga gic regions + */ +#define CNS3XXX_TC11MP_SCU_BASE 0x90000000 /* IRQ, Test chip */ +#define CNS3XXX_TC11MP_SCU_BASE_VIRT 0xFF000000 + +#define CNS3XXX_TC11MP_GIC_CPU_BASE 0x90000100 /* Test chip interrupt controller CPU interface */ +#define CNS3XXX_TC11MP_GIC_CPU_BASE_VIRT 0xFF000100 + +#define CNS3XXX_TC11MP_TWD_BASE 0x90000600 +#define CNS3XXX_TC11MP_TWD_BASE_VIRT 0xFF000600 + +#define CNS3XXX_TC11MP_GIC_DIST_BASE 0x90001000 /* Test chip interrupt controller distributor */ +#define CNS3XXX_TC11MP_GIC_DIST_BASE_VIRT 0xFF001000 + +#define CNS3XXX_TC11MP_L220_BASE 0x92002000 /* L220 registers */ +#define CNS3XXX_TC11MP_L220_BASE_VIRT 0xFF002000 + +/* + * Misc block + */ +#define MISC_MEM_MAP(offs) (void __iomem *)(CNS3XXX_MISC_BASE_VIRT + (offs)) +#define MISC_MEM_MAP_VALUE(offset) (*((volatile unsigned int *)(CNS3XXX_MISC_BASE_VIRT + (offset)))) + +#define MISC_MEMORY_REMAP_REG MISC_MEM_MAP_VALUE(0x00) +#define MISC_CHIP_CONFIG_REG MISC_MEM_MAP_VALUE(0x04) +#define MISC_DEBUG_PROBE_DATA_REG MISC_MEM_MAP_VALUE(0x08) +#define MISC_DEBUG_PROBE_SELECTION_REG MISC_MEM_MAP_VALUE(0x0C) +#define MISC_IO_PIN_FUNC_SELECTION_REG MISC_MEM_MAP_VALUE(0x10) +#define MISC_GPIOA_PIN_ENABLE_REG MISC_MEM_MAP_VALUE(0x14) +#define MISC_GPIOB_PIN_ENABLE_REG MISC_MEM_MAP_VALUE(0x18) +#define MISC_IO_PAD_DRIVE_STRENGTH_CTRL_A MISC_MEM_MAP_VALUE(0x1C) +#define MISC_IO_PAD_DRIVE_STRENGTH_CTRL_B MISC_MEM_MAP_VALUE(0x20) +#define MISC_GPIOA_15_0_PULL_CTRL_REG MISC_MEM_MAP_VALUE(0x24) +#define MISC_GPIOA_16_31_PULL_CTRL_REG MISC_MEM_MAP_VALUE(0x28) +#define MISC_GPIOB_15_0_PULL_CTRL_REG MISC_MEM_MAP_VALUE(0x2C) +#define MISC_GPIOB_16_31_PULL_CTRL_REG MISC_MEM_MAP_VALUE(0x30) +#define MISC_IO_PULL_CTRL_REG MISC_MEM_MAP_VALUE(0x34) +#define MISC_E_FUSE_31_0_REG MISC_MEM_MAP_VALUE(0x40) +#define MISC_E_FUSE_63_32_REG MISC_MEM_MAP_VALUE(0x44) +#define MISC_E_FUSE_95_64_REG MISC_MEM_MAP_VALUE(0x48) +#define MISC_E_FUSE_127_96_REG MISC_MEM_MAP_VALUE(0x4C) +#define MISC_SOFTWARE_TEST_1_REG MISC_MEM_MAP_VALUE(0x50) +#define MISC_SOFTWARE_TEST_2_REG MISC_MEM_MAP_VALUE(0x54) + +#define MISC_SATA_POWER_MODE MISC_MEM_MAP_VALUE(0x310) + +#define MISC_USB_CFG_REG MISC_MEM_MAP_VALUE(0x800) +#define MISC_USB_STS_REG MISC_MEM_MAP_VALUE(0x804) +#define MISC_USBPHY00_CFG_REG MISC_MEM_MAP_VALUE(0x808) +#define MISC_USBPHY01_CFG_REG MISC_MEM_MAP_VALUE(0x80c) +#define MISC_USBPHY10_CFG_REG MISC_MEM_MAP_VALUE(0x810) +#define MISC_USBPHY11_CFG_REG MISC_MEM_MAP_VALUE(0x814) + +#define MISC_PCIEPHY_CMCTL(x) MISC_MEM_MAP(0x900 + (x) * 0x004) +#define MISC_PCIEPHY_CTL(x) MISC_MEM_MAP(0x940 + (x) * 0x100) +#define MISC_PCIE_AXIS_AWMISC(x) MISC_MEM_MAP(0x944 + (x) * 0x100) +#define MISC_PCIE_AXIS_ARMISC(x) MISC_MEM_MAP(0x948 + (x) * 0x100) +#define MISC_PCIE_AXIS_RMISC(x) MISC_MEM_MAP(0x94C + (x) * 0x100) +#define MISC_PCIE_AXIS_BMISC(x) MISC_MEM_MAP(0x950 + (x) * 0x100) +#define MISC_PCIE_AXIM_RMISC(x) MISC_MEM_MAP(0x954 + (x) * 0x100) +#define MISC_PCIE_AXIM_BMISC(x) MISC_MEM_MAP(0x958 + (x) * 0x100) +#define MISC_PCIE_CTRL(x) MISC_MEM_MAP(0x95C + (x) * 0x100) +#define MISC_PCIE_PM_DEBUG(x) MISC_MEM_MAP(0x960 + (x) * 0x100) +#define MISC_PCIE_RFC_DEBUG(x) MISC_MEM_MAP(0x964 + (x) * 0x100) +#define MISC_PCIE_CXPL_DEBUGL(x) MISC_MEM_MAP(0x968 + (x) * 0x100) +#define MISC_PCIE_CXPL_DEBUGH(x) MISC_MEM_MAP(0x96C + (x) * 0x100) +#define MISC_PCIE_DIAG_DEBUGH(x) MISC_MEM_MAP(0x970 + (x) * 0x100) +#define MISC_PCIE_W1CLR(x) MISC_MEM_MAP(0x974 + (x) * 0x100) +#define MISC_PCIE_INT_MASK(x) MISC_MEM_MAP(0x978 + (x) * 0x100) +#define MISC_PCIE_INT_STATUS(x) MISC_MEM_MAP(0x97C + (x) * 0x100) + +/* + * Power management and clock control + */ +#define PMU_REG_VALUE(offset) (*((volatile unsigned int *)(CNS3XXX_PM_BASE_VIRT + (offset)))) + +#define PM_CLK_GATE_REG PMU_REG_VALUE(0x000) +#define PM_SOFT_RST_REG PMU_REG_VALUE(0x004) +#define PM_HS_CFG_REG PMU_REG_VALUE(0x008) +#define PM_CACTIVE_STA_REG PMU_REG_VALUE(0x00C) +#define PM_PWR_STA_REG PMU_REG_VALUE(0x010) +#define PM_CLK_CTRL_REG PMU_REG_VALUE(0x014) +#define PM_PLL_LCD_I2S_CTRL_REG PMU_REG_VALUE(0x018) +#define PM_PLL_HM_PD_CTRL_REG PMU_REG_VALUE(0x01C) +#define PM_REGULAT_CTRL_REG PMU_REG_VALUE(0x020) +#define PM_WDT_CTRL_REG PMU_REG_VALUE(0x024) +#define PM_WU_CTRL0_REG PMU_REG_VALUE(0x028) +#define PM_WU_CTRL1_REG PMU_REG_VALUE(0x02C) +#define PM_CSR_REG PMU_REG_VALUE(0x030) + +/* PM_CLK_GATE_REG */ +#define PM_CLK_GATE_REG_OFFSET_SDIO (25) +#define PM_CLK_GATE_REG_OFFSET_GPU (24) +#define PM_CLK_GATE_REG_OFFSET_CIM (23) +#define PM_CLK_GATE_REG_OFFSET_LCDC (22) +#define PM_CLK_GATE_REG_OFFSET_I2S (21) +#define PM_CLK_GATE_REG_OFFSET_RAID (20) +#define PM_CLK_GATE_REG_OFFSET_SATA (19) +#define PM_CLK_GATE_REG_OFFSET_PCIE(x) (17 + (x)) +#define PM_CLK_GATE_REG_OFFSET_USB_HOST (16) +#define PM_CLK_GATE_REG_OFFSET_USB_OTG (15) +#define PM_CLK_GATE_REG_OFFSET_TIMER (14) +#define PM_CLK_GATE_REG_OFFSET_CRYPTO (13) +#define PM_CLK_GATE_REG_OFFSET_HCIE (12) +#define PM_CLK_GATE_REG_OFFSET_SWITCH (11) +#define PM_CLK_GATE_REG_OFFSET_GPIO (10) +#define PM_CLK_GATE_REG_OFFSET_UART3 (9) +#define PM_CLK_GATE_REG_OFFSET_UART2 (8) +#define PM_CLK_GATE_REG_OFFSET_UART1 (7) +#define PM_CLK_GATE_REG_OFFSET_RTC (5) +#define PM_CLK_GATE_REG_OFFSET_GDMA (4) +#define PM_CLK_GATE_REG_OFFSET_SPI_PCM_I2C (3) +#define PM_CLK_GATE_REG_OFFSET_SMC_NFI (1) +#define PM_CLK_GATE_REG_MASK (0x03FFFFBA) + +/* PM_SOFT_RST_REG */ +#define PM_SOFT_RST_REG_OFFST_WARM_RST_FLAG (31) +#define PM_SOFT_RST_REG_OFFST_CPU1 (29) +#define PM_SOFT_RST_REG_OFFST_CPU0 (28) +#define PM_SOFT_RST_REG_OFFST_SDIO (25) +#define PM_SOFT_RST_REG_OFFST_GPU (24) +#define PM_SOFT_RST_REG_OFFST_CIM (23) +#define PM_SOFT_RST_REG_OFFST_LCDC (22) +#define PM_SOFT_RST_REG_OFFST_I2S (21) +#define PM_SOFT_RST_REG_OFFST_RAID (20) +#define PM_SOFT_RST_REG_OFFST_SATA (19) +#define PM_SOFT_RST_REG_OFFST_PCIE(x) (17 + (x)) +#define PM_SOFT_RST_REG_OFFST_USB_HOST (16) +#define PM_SOFT_RST_REG_OFFST_USB_OTG (15) +#define PM_SOFT_RST_REG_OFFST_TIMER (14) +#define PM_SOFT_RST_REG_OFFST_CRYPTO (13) +#define PM_SOFT_RST_REG_OFFST_HCIE (12) +#define PM_SOFT_RST_REG_OFFST_SWITCH (11) +#define PM_SOFT_RST_REG_OFFST_GPIO (10) +#define PM_SOFT_RST_REG_OFFST_UART3 (9) +#define PM_SOFT_RST_REG_OFFST_UART2 (8) +#define PM_SOFT_RST_REG_OFFST_UART1 (7) +#define PM_SOFT_RST_REG_OFFST_RTC (5) +#define PM_SOFT_RST_REG_OFFST_GDMA (4) +#define PM_SOFT_RST_REG_OFFST_SPI_PCM_I2C (3) +#define PM_SOFT_RST_REG_OFFST_DMC (2) +#define PM_SOFT_RST_REG_OFFST_SMC_NFI (1) +#define PM_SOFT_RST_REG_OFFST_GLOBAL (0) +#define PM_SOFT_RST_REG_MASK (0xF3FFFFBF) + +/* PMHS_CFG_REG */ +#define PM_HS_CFG_REG_OFFSET_SDIO (25) +#define PM_HS_CFG_REG_OFFSET_GPU (24) +#define PM_HS_CFG_REG_OFFSET_CIM (23) +#define PM_HS_CFG_REG_OFFSET_LCDC (22) +#define PM_HS_CFG_REG_OFFSET_I2S (21) +#define PM_HS_CFG_REG_OFFSET_RAID (20) +#define PM_HS_CFG_REG_OFFSET_SATA (19) +#define PM_HS_CFG_REG_OFFSET_PCIE1 (18) +#define PM_HS_CFG_REG_OFFSET_PCIE0 (17) +#define PM_HS_CFG_REG_OFFSET_USB_HOST (16) +#define PM_HS_CFG_REG_OFFSET_USB_OTG (15) +#define PM_HS_CFG_REG_OFFSET_TIMER (14) +#define PM_HS_CFG_REG_OFFSET_CRYPTO (13) +#define PM_HS_CFG_REG_OFFSET_HCIE (12) +#define PM_HS_CFG_REG_OFFSET_SWITCH (11) +#define PM_HS_CFG_REG_OFFSET_GPIO (10) +#define PM_HS_CFG_REG_OFFSET_UART3 (9) +#define PM_HS_CFG_REG_OFFSET_UART2 (8) +#define PM_HS_CFG_REG_OFFSET_UART1 (7) +#define PM_HS_CFG_REG_OFFSET_RTC (5) +#define PM_HS_CFG_REG_OFFSET_GDMA (4) +#define PM_HS_CFG_REG_OFFSET_SPI_PCM_I2S (3) +#define PM_HS_CFG_REG_OFFSET_DMC (2) +#define PM_HS_CFG_REG_OFFSET_SMC_NFI (1) +#define PM_HS_CFG_REG_MASK (0x03FFFFBE) +#define PM_HS_CFG_REG_MASK_SUPPORT (0x01100806) + +/* PM_CACTIVE_STA_REG */ +#define PM_CACTIVE_STA_REG_OFFSET_SDIO (25) +#define PM_CACTIVE_STA_REG_OFFSET_GPU (24) +#define PM_CACTIVE_STA_REG_OFFSET_CIM (23) +#define PM_CACTIVE_STA_REG_OFFSET_LCDC (22) +#define PM_CACTIVE_STA_REG_OFFSET_I2S (21) +#define PM_CACTIVE_STA_REG_OFFSET_RAID (20) +#define PM_CACTIVE_STA_REG_OFFSET_SATA (19) +#define PM_CACTIVE_STA_REG_OFFSET_PCIE1 (18) +#define PM_CACTIVE_STA_REG_OFFSET_PCIE0 (17) +#define PM_CACTIVE_STA_REG_OFFSET_USB_HOST (16) +#define PM_CACTIVE_STA_REG_OFFSET_USB_OTG (15) +#define PM_CACTIVE_STA_REG_OFFSET_TIMER (14) +#define PM_CACTIVE_STA_REG_OFFSET_CRYPTO (13) +#define PM_CACTIVE_STA_REG_OFFSET_HCIE (12) +#define PM_CACTIVE_STA_REG_OFFSET_SWITCH (11) +#define PM_CACTIVE_STA_REG_OFFSET_GPIO (10) +#define PM_CACTIVE_STA_REG_OFFSET_UART3 (9) +#define PM_CACTIVE_STA_REG_OFFSET_UART2 (8) +#define PM_CACTIVE_STA_REG_OFFSET_UART1 (7) +#define PM_CACTIVE_STA_REG_OFFSET_RTC (5) +#define PM_CACTIVE_STA_REG_OFFSET_GDMA (4) +#define PM_CACTIVE_STA_REG_OFFSET_SPI_PCM_I2S (3) +#define PM_CACTIVE_STA_REG_OFFSET_DMC (2) +#define PM_CACTIVE_STA_REG_OFFSET_SMC_NFI (1) +#define PM_CACTIVE_STA_REG_MASK (0x03FFFFBE) + +/* PM_PWR_STA_REG */ +#define PM_PWR_STA_REG_REG_OFFSET_SDIO (25) +#define PM_PWR_STA_REG_REG_OFFSET_GPU (24) +#define PM_PWR_STA_REG_REG_OFFSET_CIM (23) +#define PM_PWR_STA_REG_REG_OFFSET_LCDC (22) +#define PM_PWR_STA_REG_REG_OFFSET_I2S (21) +#define PM_PWR_STA_REG_REG_OFFSET_RAID (20) +#define PM_PWR_STA_REG_REG_OFFSET_SATA (19) +#define PM_PWR_STA_REG_REG_OFFSET_PCIE1 (18) +#define PM_PWR_STA_REG_REG_OFFSET_PCIE0 (17) +#define PM_PWR_STA_REG_REG_OFFSET_USB_HOST (16) +#define PM_PWR_STA_REG_REG_OFFSET_USB_OTG (15) +#define PM_PWR_STA_REG_REG_OFFSET_TIMER (14) +#define PM_PWR_STA_REG_REG_OFFSET_CRYPTO (13) +#define PM_PWR_STA_REG_REG_OFFSET_HCIE (12) +#define PM_PWR_STA_REG_REG_OFFSET_SWITCH (11) +#define PM_PWR_STA_REG_REG_OFFSET_GPIO (10) +#define PM_PWR_STA_REG_REG_OFFSET_UART3 (9) +#define PM_PWR_STA_REG_REG_OFFSET_UART2 (8) +#define PM_PWR_STA_REG_REG_OFFSET_UART1 (7) +#define PM_PWR_STA_REG_REG_OFFSET_RTC (5) +#define PM_PWR_STA_REG_REG_OFFSET_GDMA (4) +#define PM_PWR_STA_REG_REG_OFFSET_SPI_PCM_I2S (3) +#define PM_PWR_STA_REG_REG_OFFSET_DMC (2) +#define PM_PWR_STA_REG_REG_OFFSET_SMC_NFI (1) +#define PM_PWR_STA_REG_REG_MASK (0x03FFFFBE) + +/* PM_CLK_CTRL_REG */ +#define PM_CLK_CTRL_REG_OFFSET_I2S_MCLK (31) +#define PM_CLK_CTRL_REG_OFFSET_DDR2_CHG_EN (30) +#define PM_CLK_CTRL_REG_OFFSET_PCIE_REF1_EN (29) +#define PM_CLK_CTRL_REG_OFFSET_PCIE_REF0_EN (28) +#define PM_CLK_CTRL_REG_OFFSET_TIMER_SIM_MODE (27) +#define PM_CLK_CTRL_REG_OFFSET_I2SCLK_DIV (24) +#define PM_CLK_CTRL_REG_OFFSET_I2SCLK_SEL (22) +#define PM_CLK_CTRL_REG_OFFSET_CLKOUT_DIV (20) +#define PM_CLK_CTRL_REG_OFFSET_CLKOUT_SEL (16) +#define PM_CLK_CTRL_REG_OFFSET_MDC_DIV (14) +#define PM_CLK_CTRL_REG_OFFSET_CRYPTO_CLK_SEL (12) +#define PM_CLK_CTRL_REG_OFFSET_CPU_PWR_MODE (9) +#define PM_CLK_CTRL_REG_OFFSET_PLL_DDR2_SEL (7) +#define PM_CLK_CTRL_REG_OFFSET_DIV_IMMEDIATE (6) +#define PM_CLK_CTRL_REG_OFFSET_CPU_CLK_DIV (4) +#define PM_CLK_CTRL_REG_OFFSET_PLL_CPU_SEL (0) + +#define PM_CPU_CLK_DIV(DIV) { \ + PM_CLK_CTRL_REG &= ~((0x3) << PM_CLK_CTRL_REG_OFFSET_CPU_CLK_DIV); \ + PM_CLK_CTRL_REG |= (((DIV)&0x3) << PM_CLK_CTRL_REG_OFFSET_CPU_CLK_DIV); \ +} + +#define PM_PLL_CPU_SEL(CPU) { \ + PM_CLK_CTRL_REG &= ~((0xF) << PM_CLK_CTRL_REG_OFFSET_PLL_CPU_SEL); \ + PM_CLK_CTRL_REG |= (((CPU)&0xF) << PM_CLK_CTRL_REG_OFFSET_PLL_CPU_SEL); \ +} + +/* PM_PLL_LCD_I2S_CTRL_REG */ +#define PM_PLL_LCD_I2S_CTRL_REG_OFFSET_MCLK_SMC_DIV (22) +#define PM_PLL_LCD_I2S_CTRL_REG_OFFSET_R_SEL (17) +#define PM_PLL_LCD_I2S_CTRL_REG_OFFSET_PLL_LCD_P (11) +#define PM_PLL_LCD_I2S_CTRL_REG_OFFSET_PLL_LCD_M (3) +#define PM_PLL_LCD_I2S_CTRL_REG_OFFSET_PLL_LCD_S (0) + +/* PM_PLL_HM_PD_CTRL_REG */ +#define PM_PLL_HM_PD_CTRL_REG_OFFSET_SATA_PHY1 (11) +#define PM_PLL_HM_PD_CTRL_REG_OFFSET_SATA_PHY0 (10) +#define PM_PLL_HM_PD_CTRL_REG_OFFSET_PLL_I2SCD (6) +#define PM_PLL_HM_PD_CTRL_REG_OFFSET_PLL_I2S (5) +#define PM_PLL_HM_PD_CTRL_REG_OFFSET_PLL_LCD (4) +#define PM_PLL_HM_PD_CTRL_REG_OFFSET_PLL_USB (3) +#define PM_PLL_HM_PD_CTRL_REG_OFFSET_PLL_RGMII (2) +#define PM_PLL_HM_PD_CTRL_REG_MASK (0x00000C7C) + +/* PM_WDT_CTRL_REG */ +#define PM_WDT_CTRL_REG_OFFSET_RESET_CPU_ONLY (0) + +/* PM_CSR_REG - Clock Scaling Register*/ +#define PM_CSR_REG_OFFSET_CSR_EN (30) +#define PM_CSR_REG_OFFSET_CSR_NUM (0) + +#define CNS3XXX_PWR_CLK_EN(BLOCK) (0x1<<PM_CLK_GATE_REG_OFFSET_##BLOCK) + +/* Software reset*/ +#define CNS3XXX_PWR_SOFTWARE_RST(BLOCK) (0x1<<PM_SOFT_RST_REG_OFFST_##BLOCK) + +/* + * CNS3XXX support several power saving mode as following, + * DFS, IDLE, HALT, DOZE, SLEEP, Hibernate + */ +#define CNS3XXX_PWR_CPU_MODE_DFS (0) +#define CNS3XXX_PWR_CPU_MODE_IDLE (1) +#define CNS3XXX_PWR_CPU_MODE_HALT (2) +#define CNS3XXX_PWR_CPU_MODE_DOZE (3) +#define CNS3XXX_PWR_CPU_MODE_SLEEP (4) +#define CNS3XXX_PWR_CPU_MODE_HIBERNATE (5) + +#define CNS3XXX_PWR_PLL(BLOCK) (0x1<<PM_PLL_HM_PD_CTRL_REG_OFFSET_##BLOCK) +#define CNS3XXX_PWR_PLL_ALL PM_PLL_HM_PD_CTRL_REG_MASK + +/* Change CPU frequency and divider */ +#define CNS3XXX_PWR_PLL_CPU_300MHZ (0) +#define CNS3XXX_PWR_PLL_CPU_333MHZ (1) +#define CNS3XXX_PWR_PLL_CPU_366MHZ (2) +#define CNS3XXX_PWR_PLL_CPU_400MHZ (3) +#define CNS3XXX_PWR_PLL_CPU_433MHZ (4) +#define CNS3XXX_PWR_PLL_CPU_466MHZ (5) +#define CNS3XXX_PWR_PLL_CPU_500MHZ (6) +#define CNS3XXX_PWR_PLL_CPU_533MHZ (7) +#define CNS3XXX_PWR_PLL_CPU_566MHZ (8) +#define CNS3XXX_PWR_PLL_CPU_600MHZ (9) +#define CNS3XXX_PWR_PLL_CPU_633MHZ (10) +#define CNS3XXX_PWR_PLL_CPU_666MHZ (11) +#define CNS3XXX_PWR_PLL_CPU_700MHZ (12) + +#define CNS3XXX_PWR_CPU_CLK_DIV_BY1 (0) +#define CNS3XXX_PWR_CPU_CLK_DIV_BY2 (1) +#define CNS3XXX_PWR_CPU_CLK_DIV_BY4 (2) + +/* Change DDR2 frequency */ +#define CNS3XXX_PWR_PLL_DDR2_200MHZ (0) +#define CNS3XXX_PWR_PLL_DDR2_266MHZ (1) +#define CNS3XXX_PWR_PLL_DDR2_333MHZ (2) +#define CNS3XXX_PWR_PLL_DDR2_400MHZ (3) + +void cns3xxx_pwr_soft_rst(unsigned int block); +void cns3xxx_pwr_clk_en(unsigned int block); +int cns3xxx_cpu_clock(void); + +/* + * ARM11 MPCore interrupt sources (primary GIC) + */ +#define IRQ_CNS3XXX_PMU (IRQ_TC11MP_GIC_START + 0) +#define IRQ_CNS3XXX_SDIO (IRQ_TC11MP_GIC_START + 1) +#define IRQ_CNS3XXX_L2CC (IRQ_TC11MP_GIC_START + 2) +#define IRQ_CNS3XXX_RTC (IRQ_TC11MP_GIC_START + 3) +#define IRQ_CNS3XXX_I2S (IRQ_TC11MP_GIC_START + 4) +#define IRQ_CNS3XXX_PCM (IRQ_TC11MP_GIC_START + 5) +#define IRQ_CNS3XXX_SPI (IRQ_TC11MP_GIC_START + 6) +#define IRQ_CNS3XXX_I2C (IRQ_TC11MP_GIC_START + 7) +#define IRQ_CNS3XXX_CIM (IRQ_TC11MP_GIC_START + 8) +#define IRQ_CNS3XXX_GPU (IRQ_TC11MP_GIC_START + 9) +#define IRQ_CNS3XXX_LCD (IRQ_TC11MP_GIC_START + 10) +#define IRQ_CNS3XXX_GPIOA (IRQ_TC11MP_GIC_START + 11) +#define IRQ_CNS3XXX_GPIOB (IRQ_TC11MP_GIC_START + 12) +#define IRQ_CNS3XXX_UART0 (IRQ_TC11MP_GIC_START + 13) +#define IRQ_CNS3XXX_UART1 (IRQ_TC11MP_GIC_START + 14) +#define IRQ_CNS3XXX_UART2 (IRQ_TC11MP_GIC_START + 15) +#define IRQ_CNS3XXX_ARM11 (IRQ_TC11MP_GIC_START + 16) + +#define IRQ_CNS3XXX_SW_STATUS (IRQ_TC11MP_GIC_START + 17) +#define IRQ_CNS3XXX_SW_R0TXC (IRQ_TC11MP_GIC_START + 18) +#define IRQ_CNS3XXX_SW_R0RXC (IRQ_TC11MP_GIC_START + 19) +#define IRQ_CNS3XXX_SW_R0QE (IRQ_TC11MP_GIC_START + 20) +#define IRQ_CNS3XXX_SW_R0QF (IRQ_TC11MP_GIC_START + 21) +#define IRQ_CNS3XXX_SW_R1TXC (IRQ_TC11MP_GIC_START + 22) +#define IRQ_CNS3XXX_SW_R1RXC (IRQ_TC11MP_GIC_START + 23) +#define IRQ_CNS3XXX_SW_R1QE (IRQ_TC11MP_GIC_START + 24) +#define IRQ_CNS3XXX_SW_R1QF (IRQ_TC11MP_GIC_START + 25) +#define IRQ_CNS3XXX_SW_PPE (IRQ_TC11MP_GIC_START + 26) + +#define IRQ_CNS3XXX_CRYPTO (IRQ_TC11MP_GIC_START + 27) +#define IRQ_CNS3XXX_HCIE (IRQ_TC11MP_GIC_START + 28) +#define IRQ_CNS3XXX_PCIE0_DEVICE (IRQ_TC11MP_GIC_START + 29) +#define IRQ_CNS3XXX_PCIE1_DEVICE (IRQ_TC11MP_GIC_START + 30) +#define IRQ_CNS3XXX_USB_OTG (IRQ_TC11MP_GIC_START + 31) +#define IRQ_CNS3XXX_USB_EHCI (IRQ_TC11MP_GIC_START + 32) +#define IRQ_CNS3XXX_SATA (IRQ_TC11MP_GIC_START + 33) +#define IRQ_CNS3XXX_RAID (IRQ_TC11MP_GIC_START + 34) +#define IRQ_CNS3XXX_SMC (IRQ_TC11MP_GIC_START + 35) + +#define IRQ_CNS3XXX_DMAC_ABORT (IRQ_TC11MP_GIC_START + 36) +#define IRQ_CNS3XXX_DMAC0 (IRQ_TC11MP_GIC_START + 37) +#define IRQ_CNS3XXX_DMAC1 (IRQ_TC11MP_GIC_START + 38) +#define IRQ_CNS3XXX_DMAC2 (IRQ_TC11MP_GIC_START + 39) +#define IRQ_CNS3XXX_DMAC3 (IRQ_TC11MP_GIC_START + 40) +#define IRQ_CNS3XXX_DMAC4 (IRQ_TC11MP_GIC_START + 41) +#define IRQ_CNS3XXX_DMAC5 (IRQ_TC11MP_GIC_START + 42) +#define IRQ_CNS3XXX_DMAC6 (IRQ_TC11MP_GIC_START + 43) +#define IRQ_CNS3XXX_DMAC7 (IRQ_TC11MP_GIC_START + 44) +#define IRQ_CNS3XXX_DMAC8 (IRQ_TC11MP_GIC_START + 45) +#define IRQ_CNS3XXX_DMAC9 (IRQ_TC11MP_GIC_START + 46) +#define IRQ_CNS3XXX_DMAC10 (IRQ_TC11MP_GIC_START + 47) +#define IRQ_CNS3XXX_DMAC11 (IRQ_TC11MP_GIC_START + 48) +#define IRQ_CNS3XXX_DMAC12 (IRQ_TC11MP_GIC_START + 49) +#define IRQ_CNS3XXX_DMAC13 (IRQ_TC11MP_GIC_START + 50) +#define IRQ_CNS3XXX_DMAC14 (IRQ_TC11MP_GIC_START + 51) +#define IRQ_CNS3XXX_DMAC15 (IRQ_TC11MP_GIC_START + 52) +#define IRQ_CNS3XXX_DMAC16 (IRQ_TC11MP_GIC_START + 53) +#define IRQ_CNS3XXX_DMAC17 (IRQ_TC11MP_GIC_START + 54) + +#define IRQ_CNS3XXX_PCIE0_RC (IRQ_TC11MP_GIC_START + 55) +#define IRQ_CNS3XXX_PCIE1_RC (IRQ_TC11MP_GIC_START + 56) +#define IRQ_CNS3XXX_TIMER0 (IRQ_TC11MP_GIC_START + 57) +#define IRQ_CNS3XXX_TIMER1 (IRQ_TC11MP_GIC_START + 58) +#define IRQ_CNS3XXX_USB_OHCI (IRQ_TC11MP_GIC_START + 59) +#define IRQ_CNS3XXX_TIMER2 (IRQ_TC11MP_GIC_START + 60) +#define IRQ_CNS3XXX_EXTERNAL_PIN0 (IRQ_TC11MP_GIC_START + 61) +#define IRQ_CNS3XXX_EXTERNAL_PIN1 (IRQ_TC11MP_GIC_START + 62) +#define IRQ_CNS3XXX_EXTERNAL_PIN2 (IRQ_TC11MP_GIC_START + 63) + +#define NR_IRQS_CNS3XXX (IRQ_TC11MP_GIC_START + 64) + +#if !defined(NR_IRQS) || (NR_IRQS < NR_IRQS_CNS3XXX) +#undef NR_IRQS +#define NR_IRQS NR_IRQS_CNS3XXX +#endif + +#endif /* __MACH_BOARD_CNS3XXX_H */ diff --git a/arch/arm/mach-cns3xxx/include/mach/debug-macro.S b/arch/arm/mach-cns3xxx/include/mach/debug-macro.S new file mode 100644 index 0000000..d16ce7e --- /dev/null +++ b/arch/arm/mach-cns3xxx/include/mach/debug-macro.S @@ -0,0 +1,21 @@ +/* + * Debugging macro include header + * + * Copyright 1994-1999 Russell King + * Copyright 2008 Cavium Networks + * Moved from linux/arch/arm/kernel/debug.S by Ben Dooks + * + * This file is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License, Version 2, as + * published by the Free Software Foundation. + */ + + .macro addruart,rx + mrc p15, 0, \rx, c1, c0 + tst \rx, #1 @ MMU enabled? + moveq \rx, #0x10000000 + movne \rx, #0xf0000000 @ virtual base + orr \rx, \rx, #0x00009000 + .endm + +#include <asm/hardware/debug-pl01x.S> diff --git a/arch/arm/mach-cns3xxx/include/mach/entry-macro.S b/arch/arm/mach-cns3xxx/include/mach/entry-macro.S new file mode 100644 index 0000000..5e1c554 --- /dev/null +++ b/arch/arm/mach-cns3xxx/include/mach/entry-macro.S @@ -0,0 +1,82 @@ +/* + * Low-level IRQ helper macros for Cavium Networks platforms + * + * Copyright 2008 Cavium Networks + * + * This file is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License, Version 2, as + * published by the Free Software Foundation. + */ + +#include <mach/hardware.h> +#include <asm/hardware/gic.h> + + .macro disable_fiq + .endm + + .macro get_irqnr_preamble, base, tmp + ldr \base, =gic_cpu_base_addr + ldr \base, [\base] + .endm + + .macro arch_ret_to_user, tmp1, tmp2 + .endm + + /* + * The interrupt numbering scheme is defined in the + * interrupt controller spec. To wit: + * + * Interrupts 0-15 are IPI + * 16-28 are reserved + * 29-31 are local. We allow 30 to be used for the watchdog. + * 32-1020 are global + * 1021-1022 are reserved + * 1023 is "spurious" (no interrupt) + * + * For now, we ignore all local interrupts so only return an interrupt if it's + * between 30 and 1020. The test_for_ipi routine below will pick up on IPIs. + * + * A simple read from the controller will tell us the number of the highest + * priority enabled interrupt. We then just need to check whether it is in the + * valid range for an IRQ (30-1020 inclusive). + */ + + .macro get_irqnr_and_base, irqnr, irqstat, base, tmp + + ldr \irqstat, [\base, #GIC_CPU_INTACK] /* bits 12-10 = src CPU, 9-0 = int # */ + + ldr \tmp, =1021 + + bic \irqnr, \irqstat, #0x1c00 + + cmp \irqnr, #29 + cmpcc \irqnr, \irqnr + cmpne \irqnr, \tmp + cmpcs \irqnr, \irqnr + + .endm + + /* We assume that irqstat (the raw value of the IRQ acknowledge + * register) is preserved from the macro above. + * If there is an IPI, we immediately signal end of interrupt on the + * controller, since this requires the original irqstat value which + * we won't easily be able to recreate later. + */ + + .macro test_for_ipi, irqnr, irqstat, base, tmp + bic \irqnr, \irqstat, #0x1c00 + cmp \irqnr, #16 + strcc \irqstat, [\base, #GIC_CPU_EOI] + cmpcs \irqnr, \irqnr + .endm + + /* As above, this assumes that irqstat and base are preserved.. */ + + .macro test_for_ltirq, irqnr, irqstat, base, tmp + bic \irqnr, \irqstat, #0x1c00 + mov \tmp, #0 + cmp \irqnr, #29 + moveq \tmp, #1 + streq \irqstat, [\base, #GIC_CPU_EOI] + cmp \tmp, #0 + .endm diff --git a/arch/arm/mach-cns3xxx/include/mach/hardware.h b/arch/arm/mach-cns3xxx/include/mach/hardware.h new file mode 100644 index 0000000..57e0983 --- /dev/null +++ b/arch/arm/mach-cns3xxx/include/mach/hardware.h @@ -0,0 +1,22 @@ +/* + * This file contains the hardware definitions of the Cavium Networks boards. + * + * Copyright 2003 ARM Limited. + * Copyright 2008 Cavium Networks + * + * This file is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License, Version 2, as + * published by the Free Software Foundation. + */ + +#ifndef __MACH_HARDWARE_H +#define __MACH_HARDWARE_H + +#include <asm/sizes.h> + +/* macro to get at IO space when running virtually */ +#define PCIBIOS_MIN_IO 0x00000000 +#define PCIBIOS_MIN_MEM 0x00000000 +#define pcibios_assign_all_busses() 1 + +#endif diff --git a/arch/arm/mach-cns3xxx/include/mach/io.h b/arch/arm/mach-cns3xxx/include/mach/io.h new file mode 100644 index 0000000..33b6fc1 --- /dev/null +++ b/arch/arm/mach-cns3xxx/include/mach/io.h @@ -0,0 +1,17 @@ +/* + * Copyright 2008 Cavium Networks + * Copyright 2003 ARM Limited + * + * This file is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License, Version 2, as + * published by the Free Software Foundation. + */ +#ifndef __MACH_IO_H +#define __MACH_IO_H + +#define IO_SPACE_LIMIT 0xffffffff + +#define __io(a) __typesafe_io(a) +#define __mem_pci(a) (a) + +#endif diff --git a/arch/arm/mach-cns3xxx/include/mach/irqs.h b/arch/arm/mach-cns3xxx/include/mach/irqs.h new file mode 100644 index 0000000..2ab96f8 --- /dev/null +++ b/arch/arm/mach-cns3xxx/include/mach/irqs.h @@ -0,0 +1,24 @@ +/* + * Copyright 2000 Deep Blue Solutions Ltd. + * Copyright 2003 ARM Limited + * Copyright 2008 Cavium Networks + * + * This file is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License, Version 2, as + * published by the Free Software Foundation. + */ + +#ifndef __MACH_IRQS_H +#define __MACH_IRQS_H + +#define IRQ_LOCALTIMER 29 +#define IRQ_LOCALWDOG 30 +#define IRQ_TC11MP_GIC_START 32 + +#include <mach/cns3xxx.h> + +#ifndef NR_IRQS +#error "NR_IRQS not defined by the board-specific files" +#endif + +#endif diff --git a/arch/arm/mach-cns3xxx/include/mach/memory.h b/arch/arm/mach-cns3xxx/include/mach/memory.h new file mode 100644 index 0000000..3b6b769 --- /dev/null +++ b/arch/arm/mach-cns3xxx/include/mach/memory.h @@ -0,0 +1,26 @@ +/* + * Copyright 2003 ARM Limited + * Copyright 2008 Cavium Networks + * + * This file is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License, Version 2, as + * published by the Free Software Foundation. + */ + +#ifndef __MACH_MEMORY_H +#define __MACH_MEMORY_H + +/* + * Physical DRAM offset. + */ +#define PHYS_OFFSET UL(0x00000000) + +#define __phys_to_bus(x) ((x) + PHYS_OFFSET) +#define __bus_to_phys(x) ((x) - PHYS_OFFSET) + +#define __virt_to_bus(v) __phys_to_bus(__virt_to_phys(v)) +#define __bus_to_virt(b) __phys_to_virt(__bus_to_phys(b)) +#define __pfn_to_bus(p) __phys_to_bus(__pfn_to_phys(p)) +#define __bus_to_pfn(b) __phys_to_pfn(__bus_to_phys(b)) + +#endif diff --git a/arch/arm/mach-cns3xxx/include/mach/system.h b/arch/arm/mach-cns3xxx/include/mach/system.h new file mode 100644 index 0000000..58bb03a --- /dev/null +++ b/arch/arm/mach-cns3xxx/include/mach/system.h @@ -0,0 +1,29 @@ +/* + * Copyright 2000 Deep Blue Solutions Ltd + * Copyright 2003 ARM Limited + * Copyright 2008 Cavium Networks + * + * This file is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License, Version 2, as + * published by the Free Software Foundation. + */ + +#ifndef __MACH_SYSTEM_H +#define __MACH_SYSTEM_H + +#include <linux/io.h> +#include <asm/proc-fns.h> +#include <mach/hardware.h> + +static inline void arch_idle(void) +{ + /* + * This should do all the clock switching + * and wait for interrupt tricks + */ + cpu_do_idle(); +} + +void arch_reset(char mode, const char *cmd); + +#endif diff --git a/arch/arm/mach-cns3xxx/include/mach/timex.h b/arch/arm/mach-cns3xxx/include/mach/timex.h new file mode 100644 index 0000000..1fd0421 --- /dev/null +++ b/arch/arm/mach-cns3xxx/include/mach/timex.h @@ -0,0 +1,12 @@ +/* + * Cavium Networks architecture timex specifications + * + * Copyright 2003 ARM Limited + * Copyright 2008 Cavium Networks + * + * This file is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License, Version 2, as + * published by the Free Software Foundation. + */ + +#define CLOCK_TICK_RATE (50000000 / 16) diff --git a/arch/arm/mach-cns3xxx/include/mach/uncompress.h b/arch/arm/mach-cns3xxx/include/mach/uncompress.h new file mode 100644 index 0000000..de8ead9 --- /dev/null +++ b/arch/arm/mach-cns3xxx/include/mach/uncompress.h @@ -0,0 +1,55 @@ +/* + * Copyright 2003 ARM Limited + * Copyright 2008 Cavium Networks + * + * This file is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License, Version 2, as + * published by the Free Software Foundation. + */ + +#include <asm/mach-types.h> +#include <mach/hardware.h> +#include <mach/cns3xxx.h> + +#define AMBA_UART_DR(base) (*(volatile unsigned char *)((base) + 0x00)) +#define AMBA_UART_LCRH(base) (*(volatile unsigned char *)((base) + 0x2c)) +#define AMBA_UART_CR(base) (*(volatile unsigned char *)((base) + 0x30)) +#define AMBA_UART_FR(base) (*(volatile unsigned char *)((base) + 0x18)) + +/* + * Return the UART base address + */ +static inline unsigned long get_uart_base(void) +{ + if (machine_is_cns3420vb()) + return CNS3XXX_UART0_BASE; + else + return 0; +} + +/* + * This does not append a newline + */ +static inline void putc(int c) +{ + unsigned long base = get_uart_base(); + + while (AMBA_UART_FR(base) & (1 << 5)) + barrier(); + + AMBA_UART_DR(base) = c; +} + +static inline void flush(void) +{ + unsigned long base = get_uart_base(); + + while (AMBA_UART_FR(base) & (1 << 3)) + barrier(); +} + +/* + * nothing to do + */ +#define arch_decomp_setup() +#define arch_decomp_wdog() diff --git a/arch/arm/mach-cns3xxx/include/mach/vmalloc.h b/arch/arm/mach-cns3xxx/include/mach/vmalloc.h new file mode 100644 index 0000000..4d381ec --- /dev/null +++ b/arch/arm/mach-cns3xxx/include/mach/vmalloc.h @@ -0,0 +1,11 @@ +/* + * Copyright 2000 Russell King. + * Copyright 2003 ARM Limited + * Copyright 2008 Cavium Networks + * + * This file is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License, Version 2, as + * published by the Free Software Foundation. + */ + +#define VMALLOC_END 0xd8000000 diff --git a/arch/arm/mach-cns3xxx/pm.c b/arch/arm/mach-cns3xxx/pm.c new file mode 100644 index 0000000..725e1a4 --- /dev/null +++ b/arch/arm/mach-cns3xxx/pm.c @@ -0,0 +1,86 @@ +/* + * Copyright 2008 Cavium Networks + * + * This file is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License, Version 2, as + * published by the Free Software Foundation. + */ + +#include <linux/delay.h> +#include <mach/system.h> +#include <mach/cns3xxx.h> + +void cns3xxx_pwr_clk_en(unsigned int block) +{ + PM_CLK_GATE_REG |= (block & PM_CLK_GATE_REG_MASK); +} + +void cns3xxx_pwr_power_up(unsigned int block) +{ + PM_PLL_HM_PD_CTRL_REG &= ~(block & CNS3XXX_PWR_PLL_ALL); + + /* Wait for 300us for the PLL output clock locked. */ + udelay(300); +}; + +void cns3xxx_pwr_power_down(unsigned int block) +{ + /* write '1' to power down */ + PM_PLL_HM_PD_CTRL_REG |= (block & CNS3XXX_PWR_PLL_ALL); +}; + +static void cns3xxx_pwr_soft_rst_force(unsigned int block) +{ + /* + * bit 0, 28, 29 => program low to reset, + * the other else program low and then high + */ + if (block & 0x30000001) { + PM_SOFT_RST_REG &= ~(block & PM_SOFT_RST_REG_MASK); + } else { + PM_SOFT_RST_REG &= ~(block & PM_SOFT_RST_REG_MASK); + PM_SOFT_RST_REG |= (block & PM_SOFT_RST_REG_MASK); + } +} + +void cns3xxx_pwr_soft_rst(unsigned int block) +{ + static unsigned int soft_reset; + + if (soft_reset & block) { + /* SPI/I2C/GPIO use the same block, reset once. */ + return; + } else { + soft_reset |= block; + } + cns3xxx_pwr_soft_rst_force(block); +} + +void arch_reset(char mode, const char *cmd) +{ + /* + * To reset, we hit the on-board reset register + * in the system FPGA. + */ + cns3xxx_pwr_soft_rst(CNS3XXX_PWR_SOFTWARE_RST(GLOBAL)); +} + +/* + * cns3xxx_cpu_clock - return CPU/L2 clock + * aclk: cpu clock/2 + * hclk: cpu clock/4 + * pclk: cpu clock/8 + */ +int cns3xxx_cpu_clock(void) +{ + int cpu; + int cpu_sel; + int div_sel; + + cpu_sel = (PM_CLK_CTRL_REG >> PM_CLK_CTRL_REG_OFFSET_PLL_CPU_SEL) & 0xf; + div_sel = (PM_CLK_CTRL_REG >> PM_CLK_CTRL_REG_OFFSET_CPU_CLK_DIV) & 0x3; + + cpu = (300 + ((cpu_sel / 3) * 100) + ((cpu_sel % 3) * 33)) >> div_sel; + + return cpu; +} -- 1.7.0.3 ^ permalink raw reply related [flat|nested] 7+ messages in thread
* [PATCH 2/3] ARM: cns3xxx: Add CNS3420 Validation Board support 2010-03-30 19:02 [PATCH v3 0/3] Support for Cavium Networks CNS3xxx machines Anton Vorontsov 2010-03-30 19:02 ` [PATCH 1/3] ARM: cns3xxx: Add basic support for Cavium Networks CNS3xxx processors Anton Vorontsov @ 2010-03-30 19:02 ` Anton Vorontsov 2010-03-30 19:02 ` [PATCH 3/3] ARM: cns3xxx: Add defconfig for CNS3420 validation board Anton Vorontsov 2010-04-14 15:37 ` [PATCH v3 0/3] Support for Cavium Networks CNS3xxx machines Anton Vorontsov 3 siblings, 0 replies; 7+ messages in thread From: Anton Vorontsov @ 2010-03-30 19:02 UTC (permalink / raw) To: linux-arm-kernel This patch adds support for CNS3420VB rev 1.3 boards. With this patch CNS3420VB boards are able to boot up to the userspace, with a console available on UART0. Signed-off-by: Anton Vorontsov <avorontsov@mvista.com> --- arch/arm/mach-cns3xxx/Kconfig | 8 ++ arch/arm/mach-cns3xxx/Makefile | 1 + arch/arm/mach-cns3xxx/cns3420vb.c | 148 +++++++++++++++++++++++++++++++++++++ 3 files changed, 157 insertions(+), 0 deletions(-) create mode 100644 arch/arm/mach-cns3xxx/cns3420vb.c diff --git a/arch/arm/mach-cns3xxx/Kconfig b/arch/arm/mach-cns3xxx/Kconfig index 20284cd..9ebfcc4 100644 --- a/arch/arm/mach-cns3xxx/Kconfig +++ b/arch/arm/mach-cns3xxx/Kconfig @@ -1,4 +1,12 @@ menu "CNS3XXX platform type" depends on ARCH_CNS3XXX +config MACH_CNS3420VB + bool "Support for CNS3420 Validation Board" + help + Include support for the Cavium Networks CNS3420 MPCore Platform + Baseboard. + This is a platform with an on-board ARM11 MPCore and has support + for USB, USB-OTG, MMC/SD/SDIO, SATA, PCI-E, etc. + endmenu diff --git a/arch/arm/mach-cns3xxx/Makefile b/arch/arm/mach-cns3xxx/Makefile index e5e76dd..427507a 100644 --- a/arch/arm/mach-cns3xxx/Makefile +++ b/arch/arm/mach-cns3xxx/Makefile @@ -1 +1,2 @@ obj-$(CONFIG_ARCH_CNS3XXX) += core.o pm.o +obj-$(CONFIG_MACH_CNS3420VB) += cns3420vb.o diff --git a/arch/arm/mach-cns3xxx/cns3420vb.c b/arch/arm/mach-cns3xxx/cns3420vb.c new file mode 100644 index 0000000..2e30c82 --- /dev/null +++ b/arch/arm/mach-cns3xxx/cns3420vb.c @@ -0,0 +1,148 @@ +/* + * Cavium Networks CNS3420 Validation Board + * + * Copyright 2000 Deep Blue Solutions Ltd + * Copyright 2008 ARM Limited + * Copyright 2008 Cavium Networks + * Scott Shu + * Copyright 2010 MontaVista Software, LLC. + * Anton Vorontsov <avorontsov@mvista.com> + * + * This file is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License, Version 2, as + * published by the Free Software Foundation. + */ + +#include <linux/init.h> +#include <linux/kernel.h> +#include <linux/compiler.h> +#include <linux/io.h> +#include <linux/serial_core.h> +#include <linux/serial_8250.h> +#include <linux/platform_device.h> +#include <linux/mtd/mtd.h> +#include <linux/mtd/physmap.h> +#include <linux/mtd/partitions.h> +#include <asm/setup.h> +#include <asm/mach-types.h> +#include <asm/mach/arch.h> +#include <asm/mach/map.h> +#include <asm/mach/time.h> +#include <mach/hardware.h> +#include <mach/cns3xxx.h> +#include <mach/irqs.h> +#include "core.h" + +/* + * NOR Flash + */ +static struct mtd_partition cns3420_nor_partitions[] = { + { + .name = "uboot", + .size = 0x00040000, + .offset = 0, + .mask_flags = MTD_WRITEABLE, + }, { + .name = "kernel", + .size = 0x004C0000, + .offset = MTDPART_OFS_APPEND, + }, { + .name = "filesystem", + .size = 0x7000000, + .offset = MTDPART_OFS_APPEND, + }, { + .name = "filesystem2", + .size = 0x0AE0000, + .offset = MTDPART_OFS_APPEND, + }, { + .name = "ubootenv", + .size = MTDPART_SIZ_FULL, + .offset = MTDPART_OFS_APPEND, + }, +}; + +static struct physmap_flash_data cns3420_nor_pdata = { + .width = 2, + .parts = cns3420_nor_partitions, + .nr_parts = ARRAY_SIZE(cns3420_nor_partitions), +}; + +static struct resource cns3420_nor_res = { + .start = CNS3XXX_FLASH_BASE, + .end = CNS3XXX_FLASH_BASE + SZ_128M - 1, + .flags = IORESOURCE_MEM | IORESOURCE_MEM_32BIT, +}; + +static struct platform_device cns3420_nor_pdev = { + .name = "physmap-flash", + .id = 0, + .resource = &cns3420_nor_res, + .num_resources = 1, + .dev = { + .platform_data = &cns3420_nor_pdata, + }, +}; + +/* + * UART + */ +static void __init cns3420_early_serial_setup(void) +{ +#ifdef CONFIG_SERIAL_8250_CONSOLE + static struct uart_port cns3420_serial_port = { + .membase = (void __iomem *)CNS3XXX_UART0_BASE_VIRT, + .mapbase = CNS3XXX_UART0_BASE, + .irq = IRQ_CNS3XXX_UART0, + .iotype = UPIO_MEM, + .flags = UPF_BOOT_AUTOCONF | UPF_FIXED_TYPE, + .regshift = 2, + .uartclk = 24000000, + .line = 0, + .type = PORT_16550A, + .fifosize = 16, + }; + + early_serial_setup(&cns3420_serial_port); +#endif +} + +/* + * Initialization + */ +static struct platform_device *cns3420_pdevs[] __initdata = { + &cns3420_nor_pdev, +}; + +static void __init cns3420_init(void) +{ + platform_add_devices(cns3420_pdevs, ARRAY_SIZE(cns3420_pdevs)); + + pm_power_off = cns3xxx_power_off; +} + +static struct map_desc cns3420_io_desc[] __initdata = { + { + .virtual = CNS3XXX_UART0_BASE_VIRT, + .pfn = __phys_to_pfn(CNS3XXX_UART0_BASE), + .length = SZ_4K, + .type = MT_DEVICE, + }, +}; + +static void __init cns3420_map_io(void) +{ + cns3xxx_map_io(); + iotable_init(cns3420_io_desc, ARRAY_SIZE(cns3420_io_desc)); + + cns3420_early_serial_setup(); +} + +MACHINE_START(CNS3420VB, "Cavium Networks CNS3420 Validation Board") + .phys_io = CNS3XXX_UART0_BASE, + .io_pg_offst = (CNS3XXX_UART0_BASE_VIRT >> 18) & 0xfffc, + .boot_params = 0x00000100, + .map_io = cns3420_map_io, + .init_irq = cns3xxx_init_irq, + .timer = &cns3xxx_timer, + .init_machine = cns3420_init, +MACHINE_END -- 1.7.0.3 ^ permalink raw reply related [flat|nested] 7+ messages in thread
* [PATCH 3/3] ARM: cns3xxx: Add defconfig for CNS3420 validation board 2010-03-30 19:02 [PATCH v3 0/3] Support for Cavium Networks CNS3xxx machines Anton Vorontsov 2010-03-30 19:02 ` [PATCH 1/3] ARM: cns3xxx: Add basic support for Cavium Networks CNS3xxx processors Anton Vorontsov 2010-03-30 19:02 ` [PATCH 2/3] ARM: cns3xxx: Add CNS3420 Validation Board support Anton Vorontsov @ 2010-03-30 19:02 ` Anton Vorontsov 2010-04-14 15:37 ` [PATCH v3 0/3] Support for Cavium Networks CNS3xxx machines Anton Vorontsov 3 siblings, 0 replies; 7+ messages in thread From: Anton Vorontsov @ 2010-03-30 19:02 UTC (permalink / raw) To: linux-arm-kernel Signed-off-by: Anton Vorontsov <avorontsov@mvista.com> --- arch/arm/configs/cns3420vb_defconfig | 833 ++++++++++++++++++++++++++++++++++ 1 files changed, 833 insertions(+), 0 deletions(-) create mode 100644 arch/arm/configs/cns3420vb_defconfig diff --git a/arch/arm/configs/cns3420vb_defconfig b/arch/arm/configs/cns3420vb_defconfig new file mode 100644 index 0000000..d021d55 --- /dev/null +++ b/arch/arm/configs/cns3420vb_defconfig @@ -0,0 +1,833 @@ +# +# Automatically generated make config: don't edit +# Linux kernel version: 2.6.34-rc2 +# Tue Mar 30 22:41:18 2010 +# +CONFIG_ARM=y +CONFIG_SYS_SUPPORTS_APM_EMULATION=y +CONFIG_GENERIC_TIME=y +CONFIG_GENERIC_CLOCKEVENTS=y +CONFIG_HAVE_PROC_CPU=y +CONFIG_GENERIC_HARDIRQS=y +CONFIG_STACKTRACE_SUPPORT=y +CONFIG_HAVE_LATENCYTOP_SUPPORT=y +CONFIG_LOCKDEP_SUPPORT=y +CONFIG_TRACE_IRQFLAGS_SUPPORT=y +CONFIG_HARDIRQS_SW_RESEND=y +CONFIG_GENERIC_IRQ_PROBE=y +CONFIG_RWSEM_GENERIC_SPINLOCK=y +CONFIG_GENERIC_HWEIGHT=y +CONFIG_GENERIC_CALIBRATE_DELAY=y +CONFIG_NEED_DMA_MAP_STATE=y +CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y +CONFIG_OPROFILE_ARMV6=y +CONFIG_OPROFILE_ARM11_CORE=y +CONFIG_VECTORS_BASE=0xffff0000 +CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" +CONFIG_CONSTRUCTORS=y + +# +# General setup +# +CONFIG_EXPERIMENTAL=y +CONFIG_BROKEN_ON_SMP=y +CONFIG_INIT_ENV_ARG_LIMIT=32 +CONFIG_LOCALVERSION="" +# CONFIG_LOCALVERSION_AUTO is not set +CONFIG_HAVE_KERNEL_GZIP=y +CONFIG_HAVE_KERNEL_LZO=y +CONFIG_KERNEL_GZIP=y +# CONFIG_KERNEL_BZIP2 is not set +# CONFIG_KERNEL_LZMA is not set +# CONFIG_KERNEL_LZO is not set +# CONFIG_SWAP is not set +CONFIG_SYSVIPC=y +CONFIG_SYSVIPC_SYSCTL=y +# CONFIG_BSD_PROCESS_ACCT is not set + +# +# RCU Subsystem +# +CONFIG_TREE_RCU=y +# CONFIG_TREE_PREEMPT_RCU is not set +# CONFIG_TINY_RCU is not set +# CONFIG_RCU_TRACE is not set +CONFIG_RCU_FANOUT=32 +# CONFIG_RCU_FANOUT_EXACT is not set +# CONFIG_TREE_RCU_TRACE is not set +CONFIG_IKCONFIG=y +CONFIG_IKCONFIG_PROC=y +CONFIG_LOG_BUF_SHIFT=14 +CONFIG_CGROUPS=y +# CONFIG_CGROUP_DEBUG is not set +# CONFIG_CGROUP_NS is not set +# CONFIG_CGROUP_FREEZER is not set +# CONFIG_CGROUP_DEVICE is not set +# CONFIG_CPUSETS is not set +# CONFIG_CGROUP_CPUACCT is not set +# CONFIG_RESOURCE_COUNTERS is not set +# CONFIG_CGROUP_SCHED is not set +CONFIG_SYSFS_DEPRECATED=y +CONFIG_SYSFS_DEPRECATED_V2=y +CONFIG_RELAY=y +CONFIG_NAMESPACES=y +# CONFIG_UTS_NS is not set +# CONFIG_IPC_NS is not set +# CONFIG_USER_NS is not set +# CONFIG_PID_NS is not set +CONFIG_BLK_DEV_INITRD=y +CONFIG_INITRAMFS_SOURCE="" +CONFIG_RD_GZIP=y +CONFIG_RD_BZIP2=y +CONFIG_RD_LZMA=y +CONFIG_RD_LZO=y +CONFIG_CC_OPTIMIZE_FOR_SIZE=y +CONFIG_SYSCTL=y +CONFIG_ANON_INODES=y +# CONFIG_EMBEDDED is not set +CONFIG_UID16=y +CONFIG_SYSCTL_SYSCALL=y +CONFIG_KALLSYMS=y +# CONFIG_KALLSYMS_EXTRA_PASS is not set +CONFIG_HOTPLUG=y +CONFIG_PRINTK=y +CONFIG_BUG=y +CONFIG_ELF_CORE=y +CONFIG_BASE_FULL=y +CONFIG_FUTEX=y +CONFIG_EPOLL=y +CONFIG_SIGNALFD=y +CONFIG_TIMERFD=y +CONFIG_EVENTFD=y +CONFIG_SHMEM=y +CONFIG_AIO=y +CONFIG_HAVE_PERF_EVENTS=y +CONFIG_PERF_USE_VMALLOC=y + +# +# Kernel Performance Events And Counters +# +# CONFIG_PERF_EVENTS is not set +# CONFIG_PERF_COUNTERS is not set +CONFIG_VM_EVENT_COUNTERS=y +CONFIG_COMPAT_BRK=y +CONFIG_SLAB=y +# CONFIG_SLUB is not set +# CONFIG_SLOB is not set +CONFIG_PROFILING=y +CONFIG_OPROFILE=m +CONFIG_HAVE_OPROFILE=y +# CONFIG_KPROBES is not set +CONFIG_HAVE_KPROBES=y +CONFIG_HAVE_KRETPROBES=y + +# +# GCOV-based kernel profiling +# +# CONFIG_GCOV_KERNEL is not set +CONFIG_SLOW_WORK=y +# CONFIG_SLOW_WORK_DEBUG is not set +CONFIG_HAVE_GENERIC_DMA_COHERENT=y +CONFIG_SLABINFO=y +CONFIG_RT_MUTEXES=y +CONFIG_BASE_SMALL=0 +CONFIG_MODULES=y +# CONFIG_MODULE_FORCE_LOAD is not set +CONFIG_MODULE_UNLOAD=y +CONFIG_MODULE_FORCE_UNLOAD=y +CONFIG_MODVERSIONS=y +# CONFIG_MODULE_SRCVERSION_ALL is not set +CONFIG_BLOCK=y +CONFIG_LBDAF=y +# CONFIG_BLK_DEV_BSG is not set +# CONFIG_BLK_DEV_INTEGRITY is not set +# CONFIG_BLK_CGROUP is not set + +# +# IO Schedulers +# +CONFIG_IOSCHED_NOOP=y +CONFIG_IOSCHED_DEADLINE=y +CONFIG_IOSCHED_CFQ=m +# CONFIG_CFQ_GROUP_IOSCHED is not set +CONFIG_DEFAULT_DEADLINE=y +# CONFIG_DEFAULT_CFQ is not set +# CONFIG_DEFAULT_NOOP is not set +CONFIG_DEFAULT_IOSCHED="deadline" +# CONFIG_INLINE_SPIN_TRYLOCK is not set +# CONFIG_INLINE_SPIN_TRYLOCK_BH is not set +# CONFIG_INLINE_SPIN_LOCK is not set +# CONFIG_INLINE_SPIN_LOCK_BH is not set +# CONFIG_INLINE_SPIN_LOCK_IRQ is not set +# CONFIG_INLINE_SPIN_LOCK_IRQSAVE is not set +CONFIG_INLINE_SPIN_UNLOCK=y +# CONFIG_INLINE_SPIN_UNLOCK_BH is not set +CONFIG_INLINE_SPIN_UNLOCK_IRQ=y +# CONFIG_INLINE_SPIN_UNLOCK_IRQRESTORE is not set +# CONFIG_INLINE_READ_TRYLOCK is not set +# CONFIG_INLINE_READ_LOCK is not set +# CONFIG_INLINE_READ_LOCK_BH is not set +# CONFIG_INLINE_READ_LOCK_IRQ is not set +# CONFIG_INLINE_READ_LOCK_IRQSAVE is not set +CONFIG_INLINE_READ_UNLOCK=y +# CONFIG_INLINE_READ_UNLOCK_BH is not set +CONFIG_INLINE_READ_UNLOCK_IRQ=y +# CONFIG_INLINE_READ_UNLOCK_IRQRESTORE is not set +# CONFIG_INLINE_WRITE_TRYLOCK is not set +# CONFIG_INLINE_WRITE_LOCK is not set +# CONFIG_INLINE_WRITE_LOCK_BH is not set +# CONFIG_INLINE_WRITE_LOCK_IRQ is not set +# CONFIG_INLINE_WRITE_LOCK_IRQSAVE is not set +CONFIG_INLINE_WRITE_UNLOCK=y +# CONFIG_INLINE_WRITE_UNLOCK_BH is not set +CONFIG_INLINE_WRITE_UNLOCK_IRQ=y +# CONFIG_INLINE_WRITE_UNLOCK_IRQRESTORE is not set +# CONFIG_MUTEX_SPIN_ON_OWNER is not set +# CONFIG_FREEZER is not set + +# +# System Type +# +CONFIG_MMU=y +# CONFIG_ARCH_AAEC2000 is not set +# CONFIG_ARCH_INTEGRATOR is not set +# CONFIG_ARCH_REALVIEW is not set +# CONFIG_ARCH_VERSATILE is not set +# CONFIG_ARCH_AT91 is not set +# CONFIG_ARCH_BCMRING is not set +# CONFIG_ARCH_CLPS711X is not set +CONFIG_ARCH_CNS3XXX=y +# CONFIG_ARCH_GEMINI is not set +# CONFIG_ARCH_EBSA110 is not set +# CONFIG_ARCH_EP93XX is not set +# CONFIG_ARCH_FOOTBRIDGE is not set +# CONFIG_ARCH_MXC is not set +# CONFIG_ARCH_STMP3XXX is not set +# CONFIG_ARCH_NETX is not set +# CONFIG_ARCH_H720X is not set +# CONFIG_ARCH_IOP13XX is not set +# CONFIG_ARCH_IOP32X is not set +# CONFIG_ARCH_IOP33X is not set +# CONFIG_ARCH_IXP23XX is not set +# CONFIG_ARCH_IXP2000 is not set +# CONFIG_ARCH_IXP4XX is not set +# CONFIG_ARCH_L7200 is not set +# CONFIG_ARCH_DOVE is not set +# CONFIG_ARCH_KIRKWOOD is not set +# CONFIG_ARCH_LOKI is not set +# CONFIG_ARCH_MV78XX0 is not set +# CONFIG_ARCH_ORION5X is not set +# CONFIG_ARCH_MMP is not set +# CONFIG_ARCH_KS8695 is not set +# CONFIG_ARCH_NS9XXX is not set +# CONFIG_ARCH_W90X900 is not set +# CONFIG_ARCH_NUC93X is not set +# CONFIG_ARCH_PNX4008 is not set +# CONFIG_ARCH_PXA is not set +# CONFIG_ARCH_MSM is not set +# CONFIG_ARCH_SHMOBILE is not set +# CONFIG_ARCH_RPC is not set +# CONFIG_ARCH_SA1100 is not set +# CONFIG_ARCH_S3C2410 is not set +# CONFIG_ARCH_S3C64XX is not set +# CONFIG_ARCH_S5P6440 is not set +# CONFIG_ARCH_S5P6442 is not set +# CONFIG_ARCH_S5PC1XX is not set +# CONFIG_ARCH_S5PV210 is not set +# CONFIG_ARCH_SHARK is not set +# CONFIG_ARCH_LH7A40X is not set +# CONFIG_ARCH_U300 is not set +# CONFIG_ARCH_U8500 is not set +# CONFIG_ARCH_NOMADIK is not set +# CONFIG_ARCH_DAVINCI is not set +# CONFIG_ARCH_OMAP is not set + +# +# CNS3XXX platform type +# +CONFIG_MACH_CNS3420VB=y + +# +# Processor Type +# +CONFIG_CPU_V6=y +# CONFIG_CPU_32v6K is not set +CONFIG_CPU_32v6=y +CONFIG_CPU_ABRT_EV6=y +CONFIG_CPU_PABRT_V6=y +CONFIG_CPU_CACHE_V6=y +CONFIG_CPU_CACHE_VIPT=y +CONFIG_CPU_COPY_V6=y +CONFIG_CPU_TLB_V6=y +CONFIG_CPU_HAS_ASID=y +CONFIG_CPU_CP15=y +CONFIG_CPU_CP15_MMU=y + +# +# Processor Features +# +CONFIG_ARM_THUMB=y +# CONFIG_CPU_ICACHE_DISABLE is not set +# CONFIG_CPU_DCACHE_DISABLE is not set +# CONFIG_CPU_BPREDICT_DISABLE is not set +CONFIG_ARM_L1_CACHE_SHIFT=5 +CONFIG_CPU_HAS_PMU=y +# CONFIG_ARM_ERRATA_411920 is not set +CONFIG_ARM_GIC=y + +# +# Bus support +# +# CONFIG_PCI_SYSCALL is not set +# CONFIG_ARCH_SUPPORTS_MSI is not set +# CONFIG_PCCARD is not set + +# +# Kernel Features +# +# CONFIG_NO_HZ is not set +# CONFIG_HIGH_RES_TIMERS is not set +CONFIG_GENERIC_CLOCKEVENTS_BUILD=y +CONFIG_VMSPLIT_3G=y +# CONFIG_VMSPLIT_2G is not set +# CONFIG_VMSPLIT_1G is not set +CONFIG_PAGE_OFFSET=0xC0000000 +CONFIG_PREEMPT_NONE=y +# CONFIG_PREEMPT_VOLUNTARY is not set +# CONFIG_PREEMPT is not set +CONFIG_HZ=100 +CONFIG_AEABI=y +CONFIG_OABI_COMPAT=y +# CONFIG_ARCH_SPARSEMEM_DEFAULT is not set +# CONFIG_ARCH_SELECT_MEMORY_MODEL is not set +# CONFIG_HIGHMEM is not set +CONFIG_SELECT_MEMORY_MODEL=y +CONFIG_FLATMEM_MANUAL=y +# CONFIG_DISCONTIGMEM_MANUAL is not set +# CONFIG_SPARSEMEM_MANUAL is not set +CONFIG_FLATMEM=y +CONFIG_FLAT_NODE_MEM_MAP=y +CONFIG_PAGEFLAGS_EXTENDED=y +CONFIG_SPLIT_PTLOCK_CPUS=4 +# CONFIG_PHYS_ADDR_T_64BIT is not set +CONFIG_ZONE_DMA_FLAG=0 +CONFIG_VIRT_TO_BUS=y +# CONFIG_KSM is not set +CONFIG_DEFAULT_MMAP_MIN_ADDR=4096 +CONFIG_ALIGNMENT_TRAP=y +# CONFIG_UACCESS_WITH_MEMCPY is not set + +# +# Boot options +# +CONFIG_ZBOOT_ROM_TEXT=0x0 +CONFIG_ZBOOT_ROM_BSS=0x0 +CONFIG_CMDLINE="console=ttyS0,38400 mem=128M root=/dev/mmcblk0p1 ro rootwait" +# CONFIG_XIP_KERNEL is not set +# CONFIG_KEXEC is not set + +# +# CPU Power Management +# +# CONFIG_CPU_IDLE is not set + +# +# Floating point emulation +# + +# +# At least one emulation must be selected +# +# CONFIG_FPE_NWFPE is not set +# CONFIG_FPE_FASTFPE is not set +# CONFIG_VFP is not set + +# +# Userspace binary formats +# +CONFIG_BINFMT_ELF=y +# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set +CONFIG_HAVE_AOUT=y +# CONFIG_BINFMT_AOUT is not set +# CONFIG_BINFMT_MISC is not set + +# +# Power management options +# +# CONFIG_PM is not set +CONFIG_ARCH_SUSPEND_POSSIBLE=y +# CONFIG_NET is not set + +# +# Device Drivers +# + +# +# Generic Driver Options +# +CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" +# CONFIG_DEVTMPFS is not set +CONFIG_STANDALONE=y +CONFIG_PREVENT_FIRMWARE_BUILD=y +CONFIG_FW_LOADER=y +# CONFIG_FIRMWARE_IN_KERNEL is not set +CONFIG_EXTRA_FIRMWARE="" +# CONFIG_SYS_HYPERVISOR is not set +CONFIG_MTD=y +# CONFIG_MTD_DEBUG is not set +# CONFIG_MTD_TESTS is not set +# CONFIG_MTD_CONCAT is not set +CONFIG_MTD_PARTITIONS=y +# CONFIG_MTD_REDBOOT_PARTS is not set +CONFIG_MTD_CMDLINE_PARTS=y +# CONFIG_MTD_AFS_PARTS is not set +# CONFIG_MTD_AR7_PARTS is not set + +# +# User Modules And Translation Layers +# +CONFIG_MTD_CHAR=y +CONFIG_MTD_BLKDEVS=y +CONFIG_MTD_BLOCK=y +# CONFIG_FTL is not set +# CONFIG_NFTL is not set +# CONFIG_INFTL is not set +# CONFIG_RFD_FTL is not set +# CONFIG_SSFDC is not set +# CONFIG_MTD_OOPS is not set + +# +# RAM/ROM/Flash chip drivers +# +CONFIG_MTD_CFI=y +# CONFIG_MTD_JEDECPROBE is not set +CONFIG_MTD_GEN_PROBE=y +# CONFIG_MTD_CFI_ADV_OPTIONS is not set +CONFIG_MTD_MAP_BANK_WIDTH_1=y +CONFIG_MTD_MAP_BANK_WIDTH_2=y +CONFIG_MTD_MAP_BANK_WIDTH_4=y +# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set +# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set +# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set +CONFIG_MTD_CFI_I1=y +CONFIG_MTD_CFI_I2=y +# CONFIG_MTD_CFI_I4 is not set +# CONFIG_MTD_CFI_I8 is not set +# CONFIG_MTD_CFI_INTELEXT is not set +CONFIG_MTD_CFI_AMDSTD=y +# CONFIG_MTD_CFI_STAA is not set +CONFIG_MTD_CFI_UTIL=y +# CONFIG_MTD_RAM is not set +# CONFIG_MTD_ROM is not set +# CONFIG_MTD_ABSENT is not set + +# +# Mapping drivers for chip access +# +# CONFIG_MTD_COMPLEX_MAPPINGS is not set +CONFIG_MTD_PHYSMAP=y +# CONFIG_MTD_PHYSMAP_COMPAT is not set +# CONFIG_MTD_ARM_INTEGRATOR is not set +# CONFIG_MTD_PLATRAM is not set + +# +# Self-contained MTD device drivers +# +# CONFIG_MTD_SLRAM is not set +# CONFIG_MTD_PHRAM is not set +# CONFIG_MTD_MTDRAM is not set +# CONFIG_MTD_BLOCK2MTD is not set + +# +# Disk-On-Chip Device Drivers +# +# CONFIG_MTD_DOC2000 is not set +# CONFIG_MTD_DOC2001 is not set +# CONFIG_MTD_DOC2001PLUS is not set +# CONFIG_MTD_NAND is not set +# CONFIG_MTD_ONENAND is not set + +# +# LPDDR flash memory drivers +# +# CONFIG_MTD_LPDDR is not set + +# +# UBI - Unsorted block images +# +# CONFIG_MTD_UBI is not set +# CONFIG_PARPORT is not set +CONFIG_BLK_DEV=y +# CONFIG_BLK_DEV_COW_COMMON is not set +CONFIG_BLK_DEV_LOOP=y +# CONFIG_BLK_DEV_CRYPTOLOOP is not set + +# +# DRBD disabled because PROC_FS, INET or CONNECTOR not selected +# +CONFIG_BLK_DEV_RAM=y +CONFIG_BLK_DEV_RAM_COUNT=16 +CONFIG_BLK_DEV_RAM_SIZE=20000 +# CONFIG_BLK_DEV_XIP is not set +# CONFIG_CDROM_PKTCDVD is not set +# CONFIG_MISC_DEVICES is not set +CONFIG_HAVE_IDE=y +# CONFIG_IDE is not set + +# +# SCSI device support +# +CONFIG_SCSI_MOD=y +# CONFIG_RAID_ATTRS is not set +CONFIG_SCSI=y +CONFIG_SCSI_DMA=y +# CONFIG_SCSI_TGT is not set +# CONFIG_SCSI_NETLINK is not set +CONFIG_SCSI_PROC_FS=y + +# +# SCSI support type (disk, tape, CD-ROM) +# +CONFIG_BLK_DEV_SD=y +# CONFIG_CHR_DEV_ST is not set +# CONFIG_CHR_DEV_OSST is not set +# CONFIG_BLK_DEV_SR is not set +# CONFIG_CHR_DEV_SG is not set +# CONFIG_CHR_DEV_SCH is not set +# CONFIG_SCSI_MULTI_LUN is not set +# CONFIG_SCSI_CONSTANTS is not set +# CONFIG_SCSI_LOGGING is not set +# CONFIG_SCSI_SCAN_ASYNC is not set +CONFIG_SCSI_WAIT_SCAN=m + +# +# SCSI Transports +# +# CONFIG_SCSI_SPI_ATTRS is not set +# CONFIG_SCSI_FC_ATTRS is not set +# CONFIG_SCSI_SAS_LIBSAS is not set +# CONFIG_SCSI_SRP_ATTRS is not set +CONFIG_SCSI_LOWLEVEL=y +# CONFIG_LIBFC is not set +# CONFIG_LIBFCOE is not set +# CONFIG_SCSI_DEBUG is not set +# CONFIG_SCSI_DH is not set +# CONFIG_SCSI_OSD_INITIATOR is not set +CONFIG_ATA=y +# CONFIG_ATA_NONSTANDARD is not set +CONFIG_ATA_VERBOSE_ERROR=y +# CONFIG_SATA_PMP is not set +CONFIG_SATA_AHCI_PLATFORM=y +# CONFIG_ATA_SFF is not set +# CONFIG_MD is not set +# CONFIG_PHONE is not set + +# +# Input device support +# +CONFIG_INPUT=y +# CONFIG_INPUT_FF_MEMLESS is not set +# CONFIG_INPUT_POLLDEV is not set +# CONFIG_INPUT_SPARSEKMAP is not set + +# +# Userland interfaces +# +CONFIG_INPUT_MOUSEDEV=y +# CONFIG_INPUT_MOUSEDEV_PSAUX is not set +CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024 +CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768 +# CONFIG_INPUT_JOYDEV is not set +# CONFIG_INPUT_EVDEV is not set +# CONFIG_INPUT_EVBUG is not set + +# +# Input Device Drivers +# +# CONFIG_INPUT_KEYBOARD is not set +# CONFIG_INPUT_MOUSE is not set +# CONFIG_INPUT_JOYSTICK is not set +# CONFIG_INPUT_TABLET is not set +# CONFIG_INPUT_TOUCHSCREEN is not set +# CONFIG_INPUT_MISC is not set + +# +# Hardware I/O ports +# +# CONFIG_SERIO is not set +# CONFIG_GAMEPORT is not set + +# +# Character devices +# +CONFIG_VT=y +CONFIG_CONSOLE_TRANSLATIONS=y +CONFIG_VT_CONSOLE=y +CONFIG_HW_CONSOLE=y +# CONFIG_VT_HW_CONSOLE_BINDING is not set +CONFIG_DEVKMEM=y +# CONFIG_SERIAL_NONSTANDARD is not set + +# +# Serial drivers +# +CONFIG_SERIAL_8250=y +CONFIG_SERIAL_8250_CONSOLE=y +CONFIG_SERIAL_8250_NR_UARTS=4 +CONFIG_SERIAL_8250_RUNTIME_UARTS=4 +# CONFIG_SERIAL_8250_EXTENDED is not set + +# +# Non-8250 serial port support +# +CONFIG_SERIAL_CORE=y +CONFIG_SERIAL_CORE_CONSOLE=y +# CONFIG_SERIAL_TIMBERDALE is not set +CONFIG_UNIX98_PTYS=y +# CONFIG_DEVPTS_MULTIPLE_INSTANCES is not set +CONFIG_LEGACY_PTYS=y +CONFIG_LEGACY_PTY_COUNT=16 +# CONFIG_IPMI_HANDLER is not set +# CONFIG_HW_RANDOM is not set +# CONFIG_R3964 is not set +# CONFIG_RAW_DRIVER is not set +# CONFIG_TCG_TPM is not set +# CONFIG_I2C is not set +# CONFIG_SPI is not set + +# +# PPS support +# +# CONFIG_PPS is not set +# CONFIG_W1 is not set +# CONFIG_POWER_SUPPLY is not set +# CONFIG_HWMON is not set +# CONFIG_THERMAL is not set +# CONFIG_WATCHDOG is not set +CONFIG_SSB_POSSIBLE=y + +# +# Sonics Silicon Backplane +# +# CONFIG_SSB is not set + +# +# Multifunction device drivers +# +# CONFIG_MFD_CORE is not set +# CONFIG_MFD_SM501 is not set +# CONFIG_HTC_PASIC3 is not set +# CONFIG_MFD_TMIO is not set +# CONFIG_REGULATOR is not set +# CONFIG_MEDIA_SUPPORT is not set + +# +# Graphics support +# +# CONFIG_VGASTATE is not set +# CONFIG_VIDEO_OUTPUT_CONTROL is not set +# CONFIG_FB is not set +# CONFIG_BACKLIGHT_LCD_SUPPORT is not set + +# +# Display device support +# +# CONFIG_DISPLAY_SUPPORT is not set + +# +# Console display driver support +# +# CONFIG_VGA_CONSOLE is not set +CONFIG_DUMMY_CONSOLE=y +# CONFIG_SOUND is not set +# CONFIG_HID_SUPPORT is not set +# CONFIG_USB_SUPPORT is not set +CONFIG_MMC=y +# CONFIG_MMC_DEBUG is not set +# CONFIG_MMC_UNSAFE_RESUME is not set + +# +# MMC/SD/SDIO Card Drivers +# +CONFIG_MMC_BLOCK=y +CONFIG_MMC_BLOCK_BOUNCE=y +# CONFIG_SDIO_UART is not set +# CONFIG_MMC_TEST is not set + +# +# MMC/SD/SDIO Host Controller Drivers +# +CONFIG_MMC_SDHCI=y +CONFIG_MMC_SDHCI_PLTFM=y +# CONFIG_MEMSTICK is not set +# CONFIG_NEW_LEDS is not set +# CONFIG_ACCESSIBILITY is not set +CONFIG_RTC_LIB=y +# CONFIG_RTC_CLASS is not set +# CONFIG_DMADEVICES is not set +# CONFIG_AUXDISPLAY is not set +# CONFIG_UIO is not set + +# +# TI VLYNQ +# +# CONFIG_STAGING is not set + +# +# File systems +# +CONFIG_EXT2_FS=y +CONFIG_EXT2_FS_XATTR=y +# CONFIG_EXT2_FS_POSIX_ACL is not set +# CONFIG_EXT2_FS_SECURITY is not set +# CONFIG_EXT2_FS_XIP is not set +# CONFIG_EXT3_FS is not set +# CONFIG_EXT4_FS is not set +CONFIG_FS_MBCACHE=y +# CONFIG_REISERFS_FS is not set +# CONFIG_JFS_FS is not set +# CONFIG_FS_POSIX_ACL is not set +# CONFIG_XFS_FS is not set +# CONFIG_GFS2_FS is not set +# CONFIG_BTRFS_FS is not set +# CONFIG_NILFS2_FS is not set +CONFIG_FILE_LOCKING=y +CONFIG_FSNOTIFY=y +CONFIG_DNOTIFY=y +CONFIG_INOTIFY=y +CONFIG_INOTIFY_USER=y +# CONFIG_QUOTA is not set +# CONFIG_AUTOFS_FS is not set +CONFIG_AUTOFS4_FS=y +# CONFIG_FUSE_FS is not set + +# +# Caches +# +CONFIG_FSCACHE=y +# CONFIG_FSCACHE_STATS is not set +# CONFIG_FSCACHE_HISTOGRAM is not set +# CONFIG_FSCACHE_DEBUG is not set +# CONFIG_FSCACHE_OBJECT_LIST is not set +# CONFIG_CACHEFILES is not set + +# +# CD-ROM/DVD Filesystems +# +# CONFIG_ISO9660_FS is not set +# CONFIG_UDF_FS is not set + +# +# DOS/FAT/NT Filesystems +# +# CONFIG_MSDOS_FS is not set +# CONFIG_VFAT_FS is not set +# CONFIG_NTFS_FS is not set + +# +# Pseudo filesystems +# +CONFIG_PROC_FS=y +CONFIG_PROC_SYSCTL=y +CONFIG_PROC_PAGE_MONITOR=y +CONFIG_SYSFS=y +CONFIG_TMPFS=y +# CONFIG_TMPFS_POSIX_ACL is not set +# CONFIG_HUGETLB_PAGE is not set +# CONFIG_CONFIGFS_FS is not set +CONFIG_MISC_FILESYSTEMS=y +# CONFIG_ADFS_FS is not set +# CONFIG_AFFS_FS is not set +# CONFIG_HFS_FS is not set +# CONFIG_HFSPLUS_FS is not set +# CONFIG_BEFS_FS is not set +# CONFIG_BFS_FS is not set +# CONFIG_EFS_FS is not set +# CONFIG_JFFS2_FS is not set +# CONFIG_LOGFS is not set +# CONFIG_CRAMFS is not set +# CONFIG_SQUASHFS is not set +# CONFIG_VXFS_FS is not set +# CONFIG_MINIX_FS is not set +# CONFIG_OMFS_FS is not set +# CONFIG_HPFS_FS is not set +# CONFIG_QNX4FS_FS is not set +# CONFIG_ROMFS_FS is not set +# CONFIG_SYSV_FS is not set +# CONFIG_UFS_FS is not set + +# +# Partition Types +# +# CONFIG_PARTITION_ADVANCED is not set +CONFIG_MSDOS_PARTITION=y +# CONFIG_NLS is not set + +# +# Kernel hacking +# +# CONFIG_PRINTK_TIME is not set +# CONFIG_ENABLE_WARN_DEPRECATED is not set +# CONFIG_ENABLE_MUST_CHECK is not set +CONFIG_FRAME_WARN=1024 +# CONFIG_MAGIC_SYSRQ is not set +# CONFIG_STRIP_ASM_SYMS is not set +# CONFIG_UNUSED_SYMBOLS is not set +CONFIG_DEBUG_FS=y +# CONFIG_HEADERS_CHECK is not set +# CONFIG_DEBUG_KERNEL is not set +CONFIG_DEBUG_BUGVERBOSE=y +CONFIG_DEBUG_MEMORY_INIT=y +CONFIG_FRAME_POINTER=y +# CONFIG_RCU_CPU_STALL_DETECTOR is not set +# CONFIG_LKDTM is not set +# CONFIG_LATENCYTOP is not set +# CONFIG_SYSCTL_SYSCALL_CHECK is not set +CONFIG_HAVE_FUNCTION_TRACER=y +CONFIG_RING_BUFFER=y +CONFIG_RING_BUFFER_ALLOW_SWAP=y +CONFIG_TRACING_SUPPORT=y +# CONFIG_FTRACE is not set +# CONFIG_DYNAMIC_DEBUG is not set +# CONFIG_SAMPLES is not set +CONFIG_HAVE_ARCH_KGDB=y +# CONFIG_ARM_UNWIND is not set +# CONFIG_DEBUG_USER is not set +# CONFIG_OC_ETM is not set + +# +# Security options +# +# CONFIG_KEYS is not set +# CONFIG_SECURITY is not set +# CONFIG_SECURITYFS is not set +# CONFIG_DEFAULT_SECURITY_SELINUX is not set +# CONFIG_DEFAULT_SECURITY_SMACK is not set +# CONFIG_DEFAULT_SECURITY_TOMOYO is not set +CONFIG_DEFAULT_SECURITY_DAC=y +CONFIG_DEFAULT_SECURITY="" +# CONFIG_CRYPTO is not set +# CONFIG_BINARY_PRINTF is not set + +# +# Library routines +# +CONFIG_BITREVERSE=y +CONFIG_GENERIC_FIND_LAST_BIT=y +CONFIG_CRC_CCITT=y +# CONFIG_CRC16 is not set +# CONFIG_CRC_T10DIF is not set +# CONFIG_CRC_ITU_T is not set +CONFIG_CRC32=y +# CONFIG_CRC7 is not set +# CONFIG_LIBCRC32C is not set +CONFIG_ZLIB_INFLATE=y +CONFIG_LZO_DECOMPRESS=y +CONFIG_DECOMPRESS_GZIP=y +CONFIG_DECOMPRESS_BZIP2=y +CONFIG_DECOMPRESS_LZMA=y +CONFIG_DECOMPRESS_LZO=y +CONFIG_HAS_IOMEM=y +CONFIG_HAS_IOPORT=y +CONFIG_HAS_DMA=y +CONFIG_GENERIC_ATOMIC64=y -- 1.7.0.3 ^ permalink raw reply related [flat|nested] 7+ messages in thread
* [PATCH v3 0/3] Support for Cavium Networks CNS3xxx machines 2010-03-30 19:02 [PATCH v3 0/3] Support for Cavium Networks CNS3xxx machines Anton Vorontsov ` (2 preceding siblings ...) 2010-03-30 19:02 ` [PATCH 3/3] ARM: cns3xxx: Add defconfig for CNS3420 validation board Anton Vorontsov @ 2010-04-14 15:37 ` Anton Vorontsov 3 siblings, 0 replies; 7+ messages in thread From: Anton Vorontsov @ 2010-04-14 15:37 UTC (permalink / raw) To: linux-arm-kernel Hello, On Tue, Mar 30, 2010 at 11:02:16PM +0400, Anton Vorontsov wrote: > v3 is on the way... Russell, does this look OK to you? If so, I'll wait for the next mach-types update, and then will ask you to pull the cns3xxx tree (or I can submit these patches via the patch tracker if you prefer that). Oh, and can you please take a look at these two as well: [PATCH] ARM: Add support for PCI domains http://lists.infradead.org/pipermail/linux-arm-kernel/2010-March/012461.html [PATCH] ARM: cns3xxx: Add support for PCI Express ports http://lists.infradead.org/pipermail/linux-arm-kernel/2010-March/012462.html Thanks! > Changes since v2: > > - We noticed that timer2 (which was used as a clock source) causes > nanosleep system call to misbehave. Until debugged, the timer2 > support is removed. > > It's fine since timer1 is still used as a clockevent, and provides > all needed timekeeping functionality. With these patches we want > a minimal (but rock solid) CNS3xxx support, all non-essential > features can wait. > > I.e. support for the second timer can be added as a separate > patch. > > - Updated some PCIe register definitions to make PCIe integration > more smooth. > > - Updated defconfig. > > Changes since v1: > > - Addressed Russell's comments; > - CNS3420VB board support split into its own patch per Sergei's > comment; > - This series no longer include AHCI and SDHCI patches. Because of > dependencies on other trees they aren't yet suitable for inclusion, > so no need to repost them again. -- Anton Vorontsov email: cbouatmailru at gmail.com irc://irc.freenode.net/bd2 ^ permalink raw reply [flat|nested] 7+ messages in thread
end of thread, other threads:[~2010-04-14 16:15 UTC | newest] Thread overview: 7+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2010-03-30 19:02 [PATCH v3 0/3] Support for Cavium Networks CNS3xxx machines Anton Vorontsov 2010-03-30 19:02 ` [PATCH 1/3] ARM: cns3xxx: Add basic support for Cavium Networks CNS3xxx processors Anton Vorontsov 2010-04-14 15:40 ` Russell King - ARM Linux 2010-04-14 16:15 ` [PATCH v4 " Anton Vorontsov 2010-03-30 19:02 ` [PATCH 2/3] ARM: cns3xxx: Add CNS3420 Validation Board support Anton Vorontsov 2010-03-30 19:02 ` [PATCH 3/3] ARM: cns3xxx: Add defconfig for CNS3420 validation board Anton Vorontsov 2010-04-14 15:37 ` [PATCH v3 0/3] Support for Cavium Networks CNS3xxx machines Anton Vorontsov
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.