* Does xf86-video-intel 2.11.0 support interlace? Lucid 2.6.33
@ 2010-05-31 19:08 Xavier de Almeida
2010-06-01 9:16 ` Re : " Xavier de Almeida
2010-06-03 15:23 ` Marc Deop i Argemí
0 siblings, 2 replies; 7+ messages in thread
From: Xavier de Almeida @ 2010-05-31 19:08 UTC (permalink / raw)
To: intel-gfx
[-- Attachment #1.1: Type: text/plain, Size: 2762 bytes --]
Hello,
It's my first post in such mailing list. My issue is that I can't configure my old LCD supporting 1080i (interlace mode) with my Clarkdale i3 (h57) HD Graphics.
I see in the Xorg log such messages:
(II) intel(0): Not using mode "1920x1080i" (interlace mode not supported)
Therefore my 1st question is to know if interlace is supposed to work with these drivers?
Then I'd like to know what I am missing in my xorg.conf in order to be able to set this display mode (and also when the TV is not connected or powered on).
My issue is that the resolution "negotiated" is 1280x720_50.0 instead of 1920x1080i.
Thanks
XabiX
lspci:
00:02.0 VGA compatible controller [0300]: Intel Corporation Core Processor Integrated Graphics Controller [8086:0042] (rev 12)
Subsystem: Giga-byte Technology Device [1458:d000]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 29
Region 0: Memory at fb400000 (64-bit, non-prefetchable) [size=4M]
Region 2: Memory at e0000000 (64-bit, prefetchable) [size=256M]
Region 4: I/O ports at ff00 [size=8]
Capabilities: [90] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+
Address: fee0500c Data: 41a9
Capabilities: [d0] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [a4] PCIe advanced features <?>
Kernel driver in use: i915
Kernel modules: i915
My EDID:
# EDID version 1 revision 3
Section "Monitor"
# Block type: 2:0 3:fc
Identifier "TSB-TV"
VendorName "TSB"
ModelName "TSB-TV"
# Block type: 2:0 3:fc
# Block type: 2:0 3:fd
HorizSync 15-46
VertRefresh 49-61
# Max dot clock (video bandwidth) 80 MHz
# DPMS capabilities: Active off:no Suspend:no Standby:no
Mode "1920x540" # vfreq 50.044Hz, hfreq 28.125kHz
DotClock 74.250000
HTimings 1920 1968 2012 2640
VTimings 540 542 547 562
Flags "Interlace" "+HSync" "+VSync"
EndMode
Mode "1280x720" # vfreq 50.000Hz, hfreq 37.500kHz
DotClock 74.250000
HTimings 1280 1464 1504 1980
VTimings 720 725 730 750
Flags "+HSync" "+VSync"
EndMode
[-- Attachment #1.2: Type: text/html, Size: 3373 bytes --]
[-- Attachment #2: Xorg-withTV.0.log --]
[-- Type: application/octet-stream, Size: 37805 bytes --]
[ 8.710]
X.Org X Server 1.8.1
Release Date: 2010-05-11
[ 8.710] X Protocol Version 11, Revision 0
[ 8.710] Build Operating System: Linux 2.6.24-27-xen x86_64 Ubuntu
[ 8.710] Current Operating System: Linux HTPC 2.6.33-02063304-generic #02063304 SMP Mon May 17 13:10:58 UTC 2010 x86_64
[ 8.710] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-2.6.33-02063304-generic root=UUID=9eeb3950-8050-485a-a6ad-903560e55adc ro vga=794 quiet splash
[ 8.710] Build Date: 21 May 2010 04:30:29PM
[ 8.710] xorg-server 2:1.8.1+git20100521+server-1.8-branch.a8de0866-0ubuntu0sarvatt~lucid (Robert Hooker <sarvatt@ubuntu.com>)
[ 8.710] Current version of pixman: 0.19.1
[ 8.710] Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
[ 8.710] Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[ 8.710] (==) Log file: "/var/log/Xorg.0.log", Time: Mon May 31 15:58:23 2010
[ 8.711] (==) Using config file: "/etc/X11/xorg.conf"
[ 8.711] (==) Using system config directory "/usr/share/X11/xorg.conf.d"
[ 8.714] (==) ServerLayout "Default Layout"
[ 8.714] (**) |-->Screen "TV" (0)
[ 8.714] (**) | |-->Monitor "TSB-TV"
[ 8.715] (**) | |-->Device "Intel HD Graphics"
[ 8.715] (==) Automatically adding devices
[ 8.715] (==) Automatically enabling devices
[ 8.715] (WW) The directory "/usr/share/fonts/X11/cyrillic" does not exist.
[ 8.715] Entry deleted from font path.
[ 8.715] (==) FontPath set to:
/usr/share/fonts/X11/misc,
/usr/share/fonts/X11/100dpi/:unscaled,
/usr/share/fonts/X11/75dpi/:unscaled,
/usr/share/fonts/X11/Type1,
/usr/share/fonts/X11/100dpi,
/usr/share/fonts/X11/75dpi,
/var/lib/defoma/x-ttcidfont-conf.d/dirs/TrueType,
built-ins
[ 8.715] (==) ModulePath set to "/usr/lib/xorg/extra-modules,/usr/lib/xorg/modules"
[ 8.715] (II) The server relies on udev to provide the list of input devices.
If no devices become available, reconfigure udev or disable AutoAddDevices.
[ 8.715] (II) Loader magic: 0x7ce8c0
[ 8.715] (II) Module ABI versions:
[ 8.715] X.Org ANSI C Emulation: 0.4
[ 8.715] X.Org Video Driver: 7.0
[ 8.715] X.Org XInput driver : 9.0
[ 8.715] X.Org Server Extension : 3.0
[ 8.747] (--) PCI:*(0:0:2:0) 8086:0042:1458:d000 Intel Corporation Core Processor Integrated Graphics Controller rev 18, Mem @ 0xfb400000/4194304, 0xe0000000/268435456, I/O @ 0x0000ff00/8
[ 8.747] (II) Open ACPI successful (/var/run/acpid.socket)
[ 8.747] (II) LoadModule: "extmod"
[ 8.748] (II) Loading /usr/lib/xorg/modules/extensions/libextmod.so
[ 8.751] (II) Module extmod: vendor="X.Org Foundation"
[ 8.751] compiled for 1.8.1, module version = 1.0.0
[ 8.751] Module class: X.Org Server Extension
[ 8.751] ABI class: X.Org Server Extension, version 3.0
[ 8.751] (II) Loading extension MIT-SCREEN-SAVER
[ 8.751] (II) Loading extension XFree86-VidModeExtension
[ 8.751] (II) Loading extension XFree86-DGA
[ 8.751] (II) Loading extension DPMS
[ 8.751] (II) Loading extension XVideo
[ 8.751] (II) Loading extension XVideo-MotionCompensation
[ 8.751] (II) Loading extension X-Resource
[ 8.751] (II) LoadModule: "dbe"
[ 8.752] (II) Loading /usr/lib/xorg/modules/extensions/libdbe.so
[ 8.753] (II) Module dbe: vendor="X.Org Foundation"
[ 8.753] compiled for 1.8.1, module version = 1.0.0
[ 8.753] Module class: X.Org Server Extension
[ 8.753] ABI class: X.Org Server Extension, version 3.0
[ 8.753] (II) Loading extension DOUBLE-BUFFER
[ 8.753] (II) LoadModule: "glx"
[ 8.753] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[ 8.758] (II) Module glx: vendor="X.Org Foundation"
[ 8.758] compiled for 1.8.1, module version = 1.0.0
[ 8.758] ABI class: X.Org Server Extension, version 3.0
[ 8.758] (==) AIGLX enabled
[ 8.758] (II) Loading extension GLX
[ 8.760] (II) LoadModule: "record"
[ 8.760] (II) Loading /usr/lib/xorg/modules/extensions/librecord.so
[ 8.761] (II) Module record: vendor="X.Org Foundation"
[ 8.761] compiled for 1.8.1, module version = 1.13.0
[ 8.761] Module class: X.Org Server Extension
[ 8.761] ABI class: X.Org Server Extension, version 3.0
[ 8.761] (II) Loading extension RECORD
[ 8.761] (II) LoadModule: "dri"
[ 8.762] (II) Loading /usr/lib/xorg/modules/extensions/libdri.so
[ 8.763] (II) Module dri: vendor="X.Org Foundation"
[ 8.763] compiled for 1.8.1, module version = 1.0.0
[ 8.763] ABI class: X.Org Server Extension, version 3.0
[ 8.763] (II) Loading extension XFree86-DRI
[ 8.763] (II) LoadModule: "dri2"
[ 8.763] (II) Loading /usr/lib/xorg/modules/extensions/libdri2.so
[ 8.765] (II) Module dri2: vendor="X.Org Foundation"
[ 8.765] compiled for 1.8.1, module version = 1.2.0
[ 8.765] ABI class: X.Org Server Extension, version 3.0
[ 8.765] (II) Loading extension DRI2
[ 8.765] (II) LoadModule: "intel"
[ 8.765] (II) Loading /usr/lib/xorg/modules/drivers/intel_drv.so
[ 8.769] (II) Module intel: vendor="X.Org Foundation"
[ 8.769] compiled for 1.8.1, module version = 2.11.0
[ 8.769] Module class: X.Org Video Driver
[ 8.769] ABI class: X.Org Video Driver, version 7.0
[ 8.769] (II) intel: Driver for Intel Integrated Graphics Chipsets: i810,
i810-dc100, i810e, i815, i830M, 845G, 852GM/855GM, 865G, 915G,
E7221 (i915), 915GM, 945G, 945GM, 945GME, Pineview GM, Pineview G,
965G, G35, 965Q, 946GZ, 965GM, 965GME/GLE, G33, Q35, Q33, GM45,
4 Series, G45/G43, Q45/Q43, G41, B43, Clarkdale, Arrandale
[ 8.769] (++) using VT number 7
[ 8.769] (II) Primary Device is: PCI 00@00:02:0
[ 8.771] drmOpenDevice: node name is /dev/dri/card0
[ 8.771] drmOpenDevice: open result is 9, (OK)
[ 8.771] drmOpenByBusid: Searching for BusID pci:0000:00:02.0
[ 8.771] drmOpenDevice: node name is /dev/dri/card0
[ 8.771] drmOpenDevice: open result is 9, (OK)
[ 8.771] drmOpenByBusid: drmOpenMinor returns 9
[ 8.771] drmOpenByBusid: drmGetBusid reports pci:0000:00:02.0
[ 8.771] (**) intel(0): Depth 24, (--) framebuffer bpp 32
[ 8.771] (==) intel(0): RGB weight 888
[ 8.771] (==) intel(0): Default visual is TrueColor
[ 8.771] (II) intel(0): Integrated Graphics Chipset: Intel(R) Clarkdale
[ 8.771] (--) intel(0): Chipset: "Clarkdale"
[ 8.771] (==) intel(0): video overlay key set to 0x101fe
[ 8.788] (II) intel(0): Output VGA1 using monitor section TSB-TV
[ 8.788] (**) intel(0): Option "PreferredMode" "1920x1080i"
[ 8.788] (**) intel(0): Option "Enable" "true"
[ 8.797] (II) intel(0): Output HDMI1 has no monitor section
[ 8.802] (II) intel(0): Output DP1 has no monitor section
[ 9.416] (II) intel(0): Output HDMI2 using monitor section TSB-TV
[ 9.425] (II) intel(0): Output HDMI3 has no monitor section
[ 9.430] (II) intel(0): Output DP2 has no monitor section
[ 9.435] (II) intel(0): Output DP3 has no monitor section
[ 9.452] (II) intel(0): EDID for output VGA1
[ 9.452] (II) intel(0): Not using mode "1920x1080i" (interlace mode not supported)
[ 9.452] (II) intel(0): Not using mode "1920x1080_30.00" (vrefresh out of range)
[ 9.452] (II) intel(0): Not using mode "1920x1080i_30.00" (interlace mode not supported)
[ 9.452] (II) intel(0): Not using mode "1920x1080i_28.00" (interlace mode not supported)
[ 9.452] (II) intel(0): Not using mode "1920x1080_28.00" (vrefresh out of range)
[ 9.452] (II) intel(0): Not using default mode "320x175" (doublescan mode not supported)
[ 9.452] (II) intel(0): Not using default mode "320x200" (doublescan mode not supported)
[ 9.452] (II) intel(0): Not using default mode "360x200" (doublescan mode not supported)
[ 9.453] (II) intel(0): Not using default mode "320x240" (doublescan mode not supported)
[ 9.453] (II) intel(0): Not using default mode "320x240" (doublescan mode not supported)
[ 9.453] (II) intel(0): Not using default mode "320x240" (doublescan mode not supported)
[ 9.453] (II) intel(0): Not using default mode "320x240" (doublescan mode not supported)
[ 9.453] (II) intel(0): Not using default mode "400x300" (doublescan mode not supported)
[ 9.453] (II) intel(0): Not using default mode "400x300" (doublescan mode not supported)
[ 9.453] (II) intel(0): Not using default mode "800x600" (hsync out of range)
[ 9.453] (II) intel(0): Not using default mode "400x300" (doublescan mode not supported)
[ 9.453] (II) intel(0): Not using default mode "800x600" (hsync out of range)
[ 9.453] (II) intel(0): Not using default mode "400x300" (doublescan mode not supported)
[ 9.453] (II) intel(0): Not using default mode "800x600" (hsync out of range)
[ 9.453] (II) intel(0): Not using default mode "400x300" (doublescan mode not supported)
[ 9.453] (II) intel(0): Not using default mode "1024x768i" (interlace mode not supported)
[ 9.453] (II) intel(0): Not using default mode "512x384i" (doublescan mode not supported)
[ 9.453] (II) intel(0): Not using default mode "1024x768" (hsync out of range)
[ 9.453] (II) intel(0): Not using default mode "512x384" (doublescan mode not supported)
[ 9.453] (II) intel(0): Not using default mode "1024x768" (hsync out of range)
[ 9.453] (II) intel(0): Not using default mode "512x384" (doublescan mode not supported)
[ 9.453] (II) intel(0): Not using default mode "1024x768" (hsync out of range)
[ 9.453] (II) intel(0): Not using default mode "512x384" (doublescan mode not supported)
[ 9.453] (II) intel(0): Not using default mode "1024x768" (hsync out of range)
[ 9.453] (II) intel(0): Not using default mode "512x384" (doublescan mode not supported)
[ 9.453] (II) intel(0): Not using default mode "1152x864" (hsync out of range)
[ 9.453] (II) intel(0): Not using default mode "576x432" (doublescan mode not supported)
[ 9.453] (II) intel(0): Not using default mode "1280x960" (hsync out of range)
[ 9.453] (II) intel(0): Not using default mode "640x480" (doublescan mode not supported)
[ 9.453] (II) intel(0): Not using default mode "1280x960" (hsync out of range)
[ 9.453] (II) intel(0): Not using default mode "640x480" (doublescan mode not supported)
[ 9.453] (II) intel(0): Not using default mode "1280x1024" (hsync out of range)
[ 9.453] (II) intel(0): Not using default mode "640x512" (doublescan mode not supported)
[ 9.453] (II) intel(0): Not using default mode "1280x1024" (hsync out of range)
[ 9.453] (II) intel(0): Not using default mode "640x512" (doublescan mode not supported)
[ 9.453] (II) intel(0): Not using default mode "1280x1024" (hsync out of range)
[ 9.453] (II) intel(0): Not using default mode "640x512" (doublescan mode not supported)
[ 9.453] (II) intel(0): Not using default mode "1600x1200" (hsync out of range)
[ 9.453] (II) intel(0): Not using default mode "800x600" (doublescan mode not supported)
[ 9.453] (II) intel(0): Not using default mode "1600x1200" (hsync out of range)
[ 9.453] (II) intel(0): Not using default mode "800x600" (doublescan mode not supported)
[ 9.453] (II) intel(0): Not using default mode "1600x1200" (hsync out of range)
[ 9.453] (II) intel(0): Not using default mode "800x600" (doublescan mode not supported)
[ 9.453] (II) intel(0): Not using default mode "1600x1200" (hsync out of range)
[ 9.453] (II) intel(0): Not using default mode "800x600" (doublescan mode not supported)
[ 9.453] (II) intel(0): Not using default mode "1600x1200" (hsync out of range)
[ 9.453] (II) intel(0): Not using default mode "800x600" (doublescan mode not supported)
[ 9.453] (II) intel(0): Not using default mode "1792x1344" (hsync out of range)
[ 9.453] (II) intel(0): Not using default mode "896x672" (doublescan mode not supported)
[ 9.453] (II) intel(0): Not using default mode "1792x1344" (hsync out of range)
[ 9.453] (II) intel(0): Not using default mode "896x672" (doublescan mode not supported)
[ 9.453] (II) intel(0): Not using default mode "1856x1392" (hsync out of range)
[ 9.453] (II) intel(0): Not using default mode "928x696" (doublescan mode not supported)
[ 9.453] (II) intel(0): Not using default mode "1856x1392" (hsync out of range)
[ 9.453] (II) intel(0): Not using default mode "928x696" (doublescan mode not supported)
[ 9.453] (II) intel(0): Not using default mode "1920x1440" (hsync out of range)
[ 9.453] (II) intel(0): Not using default mode "960x720" (doublescan mode not supported)
[ 9.453] (II) intel(0): Not using default mode "1920x1440" (hsync out of range)
[ 9.453] (II) intel(0): Not using default mode "960x720" (doublescan mode not supported)
[ 9.453] (II) intel(0): Not using default mode "832x624" (hsync out of range)
[ 9.453] (II) intel(0): Not using default mode "416x312" (doublescan mode not supported)
[ 9.453] (II) intel(0): Not using default mode "1152x864" (hsync out of range)
[ 9.453] (II) intel(0): Not using default mode "576x432" (doublescan mode not supported)
[ 9.453] (II) intel(0): Not using default mode "1152x864" (hsync out of range)
[ 9.453] (II) intel(0): Not using default mode "576x432" (doublescan mode not supported)
[ 9.453] (II) intel(0): Not using default mode "1152x864" (hsync out of range)
[ 9.453] (II) intel(0): Not using default mode "576x432" (doublescan mode not supported)
[ 9.453] (II) intel(0): Not using default mode "1152x864" (hsync out of range)
[ 9.453] (II) intel(0): Not using default mode "576x432" (doublescan mode not supported)
[ 9.453] (II) intel(0): Not using default mode "1152x864" (hsync out of range)
[ 9.453] (II) intel(0): Not using default mode "576x432" (doublescan mode not supported)
[ 9.453] (II) intel(0): Not using default mode "1152x864" (hsync out of range)
[ 9.453] (II) intel(0): Not using default mode "576x432" (doublescan mode not supported)
[ 9.453] (II) intel(0): Not using default mode "1360x768" (hsync out of range)
[ 9.453] (II) intel(0): Not using default mode "680x384" (doublescan mode not supported)
[ 9.453] (II) intel(0): Not using default mode "1360x768" (hsync out of range)
[ 9.453] (II) intel(0): Not using default mode "680x384" (doublescan mode not supported)
[ 9.453] (II) intel(0): Not using default mode "1400x1050" (hsync out of range)
[ 9.453] (II) intel(0): Not using default mode "700x525" (doublescan mode not supported)
[ 9.453] (II) intel(0): Not using default mode "1400x1050" (hsync out of range)
[ 9.453] (II) intel(0): Not using default mode "700x525" (doublescan mode not supported)
[ 9.453] (II) intel(0): Not using default mode "1400x1050" (hsync out of range)
[ 9.453] (II) intel(0): Not using default mode "700x525" (doublescan mode not supported)
[ 9.453] (II) intel(0): Not using default mode "1400x1050" (hsync out of range)
[ 9.453] (II) intel(0): Not using default mode "700x525" (doublescan mode not supported)
[ 9.453] (II) intel(0): Not using default mode "1440x900" (hsync out of range)
[ 9.453] (II) intel(0): Not using default mode "720x450" (doublescan mode not supported)
[ 9.453] (II) intel(0): Not using default mode "1600x1024" (hsync out of range)
[ 9.453] (II) intel(0): Not using default mode "800x512" (doublescan mode not supported)
[ 9.453] (II) intel(0): Not using default mode "1680x1050" (hsync out of range)
[ 9.453] (II) intel(0): Not using default mode "840x525" (doublescan mode not supported)
[ 9.453] (II) intel(0): Not using default mode "1680x1050" (hsync out of range)
[ 9.453] (II) intel(0): Not using default mode "840x525" (doublescan mode not supported)
[ 9.453] (II) intel(0): Not using default mode "1680x1050" (hsync out of range)
[ 9.453] (II) intel(0): Not using default mode "840x525" (doublescan mode not supported)
[ 9.453] (II) intel(0): Not using default mode "1680x1050" (hsync out of range)
[ 9.453] (II) intel(0): Not using default mode "840x525" (doublescan mode not supported)
[ 9.453] (II) intel(0): Not using default mode "1680x1050" (hsync out of range)
[ 9.453] (II) intel(0): Not using default mode "840x525" (doublescan mode not supported)
[ 9.453] (II) intel(0): Not using default mode "1920x1080" (hsync out of range)
[ 9.453] (II) intel(0): Not using default mode "960x540" (doublescan mode not supported)
[ 9.453] (II) intel(0): Not using default mode "1920x1200" (hsync out of range)
[ 9.453] (II) intel(0): Not using default mode "960x600" (doublescan mode not supported)
[ 9.453] (II) intel(0): Not using default mode "1920x1440" (hsync out of range)
[ 9.453] (II) intel(0): Not using default mode "960x720" (doublescan mode not supported)
[ 9.453] (II) intel(0): Not using default mode "2048x1536" (hsync out of range)
[ 9.453] (II) intel(0): Not using default mode "1024x768" (doublescan mode not supported)
[ 9.453] (II) intel(0): Not using default mode "2048x1536" (hsync out of range)
[ 9.453] (II) intel(0): Not using default mode "1024x768" (doublescan mode not supported)
[ 9.453] (II) intel(0): Not using default mode "2048x1536" (hsync out of range)
[ 9.453] (II) intel(0): Not using default mode "1024x768" (doublescan mode not supported)
[ 9.453] (II) intel(0): Printing probed modes for output VGA1
[ 9.453] (II) intel(0): Modeline "1280x720_50.0"x50.0 74.25 1280 1720 1760 1980 720 725 730 750 +hsync +vsync (37.5 kHz)
[ 9.453] (II) intel(0): Modeline "800x600"x60.3 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz)
[ 9.453] (II) intel(0): Modeline "800x600"x56.2 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz)
[ 9.453] (II) intel(0): Modeline "640x480"x85.0 36.00 640 696 752 832 480 481 484 509 -hsync -vsync (43.3 kHz)
[ 9.453] (II) intel(0): Modeline "640x480"x72.8 31.50 640 664 704 832 480 489 492 520 -hsync -vsync (37.9 kHz)
[ 9.453] (II) intel(0): Modeline "640x480"x75.0 31.50 640 656 720 840 480 481 484 500 -hsync -vsync (37.5 kHz)
[ 9.453] (II) intel(0): Modeline "640x480"x59.9 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz)
[ 9.453] (II) intel(0): Modeline "720x400"x85.0 35.50 720 756 828 936 400 401 404 446 -hsync +vsync (37.9 kHz)
[ 9.453] (II) intel(0): Modeline "640x400"x85.1 31.50 640 672 736 832 400 401 404 445 -hsync +vsync (37.9 kHz)
[ 9.453] (II) intel(0): Modeline "640x350"x85.1 31.50 640 672 736 832 350 382 385 445 +hsync -vsync (37.9 kHz)
[ 9.462] (II) intel(0): EDID for output HDMI1
[ 9.467] (II) intel(0): EDID for output DP1
[ 10.082] (II) intel(0): EDID for output HDMI2
[ 10.082] (II) intel(0): Manufacturer: TSB Model: 103 Serial#: 0
[ 10.082] (II) intel(0): Year: 2006 Week: 0
[ 10.082] (II) intel(0): EDID Version: 1.3
[ 10.082] (II) intel(0): Digital Display Input
[ 10.082] (II) intel(0): Max Image Size [cm]: horiz.: 196 vert.: 142
[ 10.082] (II) intel(0): Gamma: 1.00
[ 10.082] (II) intel(0): No DPMS capabilities specified
[ 10.082] (II) intel(0): Supported color encodings: RGB 4:4:4 YCrCb 4:4:4
[ 10.082] (II) intel(0): Default color space is primary color space
[ 10.082] (II) intel(0): First detailed timing is preferred mode
[ 10.082] (II) intel(0): redX: 0.640 redY: 0.330 greenX: 0.300 greenY: 0.600
[ 10.082] (II) intel(0): blueX: 0.150 blueY: 0.060 whiteX: 0.312 whiteY: 0.329
[ 10.082] (II) intel(0): Manufacturer's mask: 0
[ 10.083] (II) intel(0): Supported detailed timing:
[ 10.083] (II) intel(0): clock: 74.2 MHz Image Size: 708 x 398 mm
[ 10.083] (II) intel(0): h_active: 1920 h_sync: 2448 h_sync_end 2492 h_blank_end 2640 h_border: 0
[ 10.083] (II) intel(0): v_active: 540 v_sync: 542 v_sync_end 547 v_blanking: 562 v_border: 0
[ 10.083] (II) intel(0): Supported detailed timing:
[ 10.083] (II) intel(0): clock: 74.2 MHz Image Size: 708 x 398 mm
[ 10.083] (II) intel(0): h_active: 1280 h_sync: 1720 h_sync_end 1760 h_blank_end 1980 h_border: 0
[ 10.083] (II) intel(0): v_active: 720 v_sync: 725 v_sync_end 730 v_blanking: 750 v_border: 0
[ 10.083] (II) intel(0): Monitor name: TSB-TV
[ 10.083] (II) intel(0): Ranges: V min: 49 V max: 61 Hz, H min: 15 H max: 46 kHz, PixClock max 80 MHz
[ 10.083] (II) intel(0): Number of EDID sections to follow: 1
[ 10.083] (II) intel(0): EDID (in hex):
[ 10.083] (II) intel(0): 00ffffffffffff005262030100000000
[ 10.083] (II) intel(0): 0010010380c48e000eee91a3544c9926
[ 10.083] (II) intel(0): 0f505400000001010101010101010101
[ 10.083] (II) intel(0): 010101010101011d80d0721c1620102c
[ 10.083] (II) intel(0): 2580c48e2100009e011d00bc52d01e20
[ 10.083] (II) intel(0): b8285540c48e2100001e000000fc0054
[ 10.083] (II) intel(0): 53422d54560a202020202020000000fd
[ 10.083] (II) intel(0): 00313d0f2e08000a20202020202001b1
[ 10.083] (II) intel(0): Not using mode "1920x1080i" (interlace mode not supported)
[ 10.083] (II) intel(0): Not using mode "1920x1080_30.00" (vrefresh out of range)
[ 10.083] (II) intel(0): Not using mode "1920x1080i_30.00" (interlace mode not supported)
[ 10.083] (II) intel(0): Not using mode "1920x1080i_28.00" (interlace mode not supported)
[ 10.083] (II) intel(0): Not using mode "1920x1080_28.00" (vrefresh out of range)
[ 10.083] (II) intel(0): Printing probed modes for output HDMI2
[ 10.083] (II) intel(0): Modeline "1280x720_50.0"x50.0 74.25 1280 1720 1760 1980 720 725 730 750 +hsync +vsync (37.5 kHz)
[ 10.083] (II) intel(0): Modeline "1280x720"x50.0 74.25 1280 1720 1760 1980 720 725 730 750 +hsync +vsync (37.5 kHz)
[ 10.083] (II) intel(0): Modeline "720x576"x50.0 27.00 720 732 796 864 576 581 586 625 -hsync -vsync (31.2 kHz)
[ 10.092] (II) intel(0): EDID for output HDMI3
[ 10.097] (II) intel(0): EDID for output DP2
[ 10.102] (II) intel(0): EDID for output DP3
[ 10.103] (II) intel(0): Output VGA1 enabled by config file
[ 10.103] (II) intel(0): Output HDMI1 disconnected
[ 10.103] (II) intel(0): Output DP1 disconnected
[ 10.103] (II) intel(0): Output HDMI2 enabled by config file
[ 10.103] (II) intel(0): Output HDMI3 disconnected
[ 10.103] (II) intel(0): Output DP2 disconnected
[ 10.103] (II) intel(0): Output DP3 disconnected
[ 10.103] (II) intel(0): Using sloppy heuristic for initial modes
[ 10.103] (II) intel(0): Output VGA1 using initial mode 1280x720_50.0
[ 10.103] (II) intel(0): Output HDMI2 using initial mode 1280x720_50.0
[ 10.103] (II) intel(0): Using default gamma of (1.0, 1.0, 1.0) unless otherwise stated.
[ 10.103] (II) intel(0): Kernel page flipping support detected, enabling
[ 10.103] (==) intel(0): DPI set to (96, 96)
[ 10.103] (II) Loading sub module "fb"
[ 10.103] (II) LoadModule: "fb"
[ 10.103] (II) Loading /usr/lib/xorg/modules/libfb.so
[ 10.110] (II) Module fb: vendor="X.Org Foundation"
[ 10.110] compiled for 1.8.1, module version = 1.0.0
[ 10.110] ABI class: X.Org ANSI C Emulation, version 0.4
[ 10.110] (==) Depth 24 pixmap format is 32 bpp
[ 10.110] (II) intel(0): [DRI2] Setup complete
[ 10.110] (II) intel(0): [DRI2] DRI driver: i965
[ 10.110] (**) intel(0): Tiling enabled
[ 10.110] (**) intel(0): SwapBuffers wait enabled
[ 10.110] (==) intel(0): VideoRam: 262144 KB
[ 10.110] (II) intel(0): Attempting memory allocation with tiled buffers.
[ 10.110] (II) intel(0): Tiled allocation successful.
[ 10.117] (II) UXA(0): Driver registered support for the following operations:
[ 10.117] (II) solid
[ 10.117] (II) copy
[ 10.117] (II) composite (RENDER acceleration)
[ 10.117] (II) put_image
[ 10.117] (==) intel(0): Backing store disabled
[ 10.117] (==) intel(0): Silken mouse enabled
[ 10.117] (II) intel(0): Initializing HW Cursor
[ 10.322] (II) intel(0): RandR 1.2 enabled, ignore the following RandR disabled message.
[ 10.323] (==) intel(0): DPMS enabled
[ 10.323] (==) intel(0): Intel XvMC decoder enabled
[ 10.323] (II) intel(0): Set up textured video
[ 10.323] (II) intel(0): [XvMC] xvmc_vld driver initialized.
[ 10.323] (II) intel(0): direct rendering: DRI2 Enabled
[ 10.323] (WW) intel(0): Option "ConnectedMonitor" is not used
[ 10.323] (WW) intel(0): Option "CustomEDID" is not used
[ 10.323] (WW) intel(0): Option "Enable" is not used
[ 10.323] (WW) intel(0): Option "PreferredMode" is not used
[ 10.323] (--) RandR disabled
[ 10.323] (II) Initializing built-in extension Generic Event Extension
[ 10.323] (II) Initializing built-in extension SHAPE
[ 10.323] (II) Initializing built-in extension MIT-SHM
[ 10.323] (II) Initializing built-in extension XInputExtension
[ 10.323] (II) Initializing built-in extension XTEST
[ 10.323] (II) Initializing built-in extension BIG-REQUESTS
[ 10.323] (II) Initializing built-in extension SYNC
[ 10.323] (II) Initializing built-in extension XKEYBOARD
[ 10.323] (II) Initializing built-in extension XC-MISC
[ 10.323] (II) Initializing built-in extension SECURITY
[ 10.323] (II) Initializing built-in extension XINERAMA
[ 10.323] (II) Initializing built-in extension XFIXES
[ 10.323] (II) Initializing built-in extension RENDER
[ 10.323] (II) Initializing built-in extension RANDR
[ 10.323] (II) Initializing built-in extension COMPOSITE
[ 10.323] (II) Initializing built-in extension DAMAGE
[ 10.340] (II) AIGLX: enabled GLX_MESA_copy_sub_buffer
[ 10.340] (II) AIGLX: enabled GLX_INTEL_swap_event
[ 10.340] (II) AIGLX: enabled GLX_SGI_swap_control and GLX_MESA_swap_control
[ 10.340] (II) AIGLX: enabled GLX_SGI_make_current_read
[ 10.340] (II) AIGLX: GLX_EXT_texture_from_pixmap backed by buffer objects
[ 10.340] (II) AIGLX: Loaded and initialized /usr/lib/dri/i965_dri.so
[ 10.340] (II) GLX: Initialized DRI2 GL provider for screen 0
[ 10.341] (II) intel(0): Setting screen physical size to 338 x 190
[ 10.435] (II) config/udev: Adding input device Power Button (/dev/input/event1)
[ 10.435] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[ 10.435] (II) LoadModule: "evdev"
[ 10.435] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 10.436] (II) Module evdev: vendor="X.Org Foundation"
[ 10.436] compiled for 1.8.0.902, module version = 2.4.0
[ 10.436] Module class: X.Org XInput Driver
[ 10.436] ABI class: X.Org XInput driver, version 9.0
[ 10.436] (**) Power Button: always reports core events
[ 10.436] (**) Power Button: Device: "/dev/input/event1"
[ 10.471] (--) Power Button: Found keys
[ 10.471] (II) Power Button: Configuring as keyboard
[ 10.471] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD)
[ 10.471] (**) Option "xkb_rules" "evdev"
[ 10.471] (**) Option "xkb_model" "pc105"
[ 10.471] (**) Option "xkb_layout" "fr"
[ 10.471] (**) Option "xkb_variant" "oss"
[ 10.499] (II) config/udev: Adding input device Power Button (/dev/input/event0)
[ 10.499] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[ 10.499] (**) Power Button: always reports core events
[ 10.499] (**) Power Button: Device: "/dev/input/event0"
[ 10.521] (--) Power Button: Found keys
[ 10.521] (II) Power Button: Configuring as keyboard
[ 10.521] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD)
[ 10.521] (**) Option "xkb_rules" "evdev"
[ 10.521] (**) Option "xkb_model" "pc105"
[ 10.521] (**) Option "xkb_layout" "fr"
[ 10.521] (**) Option "xkb_variant" "oss"
[ 10.523] (II) config/udev: Adding input device HDA Digital PCBeep (/dev/input/event5)
[ 10.523] (II) No input driver/identifier specified (ignoring)
[ 10.525] (II) config/udev: Adding input device Kensington Kensington Ci75m Wireless Notebook Mouse (/dev/input/event3)
[ 10.525] (**) Kensington Kensington Ci75m Wireless Notebook Mouse: Applying InputClass "evdev pointer catchall"
[ 10.525] (**) Kensington Kensington Ci75m Wireless Notebook Mouse: always reports core events
[ 10.525] (**) Kensington Kensington Ci75m Wireless Notebook Mouse: Device: "/dev/input/event3"
[ 10.551] (--) Kensington Kensington Ci75m Wireless Notebook Mouse: Found 3 mouse buttons
[ 10.551] (--) Kensington Kensington Ci75m Wireless Notebook Mouse: Found scroll wheel(s)
[ 10.551] (--) Kensington Kensington Ci75m Wireless Notebook Mouse: Found relative axes
[ 10.551] (--) Kensington Kensington Ci75m Wireless Notebook Mouse: Found x and y relative axes
[ 10.551] (II) Kensington Kensington Ci75m Wireless Notebook Mouse: Configuring as mouse
[ 10.551] (**) Kensington Kensington Ci75m Wireless Notebook Mouse: YAxisMapping: buttons 4 and 5
[ 10.551] (**) Kensington Kensington Ci75m Wireless Notebook Mouse: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[ 10.551] (II) XINPUT: Adding extended input device "Kensington Kensington Ci75m Wireless Notebook Mouse" (type: MOUSE)
[ 10.551] (**) Kensington Kensington Ci75m Wireless Notebook Mouse: (accel) keeping acceleration scheme 1
[ 10.551] (**) Kensington Kensington Ci75m Wireless Notebook Mouse: (accel) acceleration profile 0
[ 10.551] (**) Kensington Kensington Ci75m Wireless Notebook Mouse: (accel) acceleration factor: 2.000
[ 10.551] (**) Kensington Kensington Ci75m Wireless Notebook Mouse: (accel) acceleration threshold: 4
[ 10.551] (II) Kensington Kensington Ci75m Wireless Notebook Mouse: initialized for relative axes.
[ 10.552] (II) config/udev: Adding input device Kensington Kensington Ci75m Wireless Notebook Mouse (/dev/input/mouse1)
[ 10.552] (II) No input driver/identifier specified (ignoring)
[ 10.552] (II) config/udev: Adding input device iMON PAD IR Mouse (15c2:0038) (/dev/input/event4)
[ 10.552] (**) iMON PAD IR Mouse (15c2:0038): Applying InputClass "evdev pointer catchall"
[ 10.552] (**) iMON PAD IR Mouse (15c2:0038): always reports core events
[ 10.553] (**) iMON PAD IR Mouse (15c2:0038): Device: "/dev/input/event4"
[ 10.583] (--) iMON PAD IR Mouse (15c2:0038): Found 9 mouse buttons
[ 10.583] (--) iMON PAD IR Mouse (15c2:0038): Found scroll wheel(s)
[ 10.583] (--) iMON PAD IR Mouse (15c2:0038): Found relative axes
[ 10.583] (--) iMON PAD IR Mouse (15c2:0038): Found x and y relative axes
[ 10.583] (II) iMON PAD IR Mouse (15c2:0038): Configuring as mouse
[ 10.583] (**) iMON PAD IR Mouse (15c2:0038): YAxisMapping: buttons 4 and 5
[ 10.583] (**) iMON PAD IR Mouse (15c2:0038): EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[ 10.583] (II) XINPUT: Adding extended input device "iMON PAD IR Mouse (15c2:0038)" (type: MOUSE)
[ 10.583] (**) iMON PAD IR Mouse (15c2:0038): (accel) keeping acceleration scheme 1
[ 10.583] (**) iMON PAD IR Mouse (15c2:0038): (accel) acceleration profile 0
[ 10.583] (**) iMON PAD IR Mouse (15c2:0038): (accel) acceleration factor: 2.000
[ 10.583] (**) iMON PAD IR Mouse (15c2:0038): (accel) acceleration threshold: 4
[ 10.583] (II) iMON PAD IR Mouse (15c2:0038): initialized for relative axes.
[ 10.583] (II) config/udev: Adding input device iMON PAD IR Mouse (15c2:0038) (/dev/input/mouse2)
[ 10.583] (II) No input driver/identifier specified (ignoring)
[ 10.588] (II) config/udev: Adding input device IR-receiver inside an USB DVB receiver (/dev/input/event6)
[ 10.588] (**) IR-receiver inside an USB DVB receiver: Applying InputClass "evdev keyboard catchall"
[ 10.588] (**) IR-receiver inside an USB DVB receiver: always reports core events
[ 10.588] (**) IR-receiver inside an USB DVB receiver: Device: "/dev/input/event6"
[ 10.611] (--) IR-receiver inside an USB DVB receiver: Found keys
[ 10.611] (II) IR-receiver inside an USB DVB receiver: Configuring as keyboard
[ 10.611] (II) XINPUT: Adding extended input device "IR-receiver inside an USB DVB receiver" (type: KEYBOARD)
[ 10.611] (**) Option "xkb_rules" "evdev"
[ 10.611] (**) Option "xkb_model" "pc105"
[ 10.611] (**) Option "xkb_layout" "fr"
[ 10.611] (**) Option "xkb_variant" "oss"
[ 10.621] (II) config/udev: Adding input device Macintosh mouse button emulation (/dev/input/event2)
[ 10.621] (**) Macintosh mouse button emulation: Applying InputClass "evdev pointer catchall"
[ 10.622] (**) Macintosh mouse button emulation: always reports core events
[ 10.622] (**) Macintosh mouse button emulation: Device: "/dev/input/event2"
[ 10.671] (--) Macintosh mouse button emulation: Found 3 mouse buttons
[ 10.671] (--) Macintosh mouse button emulation: Found relative axes
[ 10.671] (--) Macintosh mouse button emulation: Found x and y relative axes
[ 10.671] (II) Macintosh mouse button emulation: Configuring as mouse
[ 10.671] (**) Macintosh mouse button emulation: YAxisMapping: buttons 4 and 5
[ 10.671] (**) Macintosh mouse button emulation: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[ 10.671] (II) XINPUT: Adding extended input device "Macintosh mouse button emulation" (type: MOUSE)
[ 10.671] (**) Macintosh mouse button emulation: (accel) keeping acceleration scheme 1
[ 10.671] (**) Macintosh mouse button emulation: (accel) acceleration profile 0
[ 10.671] (**) Macintosh mouse button emulation: (accel) acceleration factor: 2.000
[ 10.671] (**) Macintosh mouse button emulation: (accel) acceleration threshold: 4
[ 10.671] (II) Macintosh mouse button emulation: initialized for relative axes.
[ 10.671] (II) config/udev: Adding input device Macintosh mouse button emulation (/dev/input/mouse0)
[ 10.671] (II) No input driver/identifier specified (ignoring)
[ 11.738] (II) intel(0): EDID vendor "TSB", prod id 259
[ 11.738] (II) intel(0): Using hsync ranges from config file
[ 11.738] (II) intel(0): Using vrefresh ranges from config file
[ 11.738] (II) intel(0): Printing DDC gathered Modelines:
[ 11.738] (II) intel(0): Modeline "1920x1080i"x0.0 74.25 1920 2448 2492 2640 1080 1084 1094 1125 interlace +hsync +vsync (28.1 kHz)
[ 11.738] (II) intel(0): Modeline "1280x720"x0.0 74.25 1280 1720 1760 1980 720 725 730 750 +hsync +vsync (37.5 kHz)
[ 12.407] (II) intel(0): EDID vendor "TSB", prod id 259
[ 12.407] (II) intel(0): Using hsync ranges from config file
[ 12.407] (II) intel(0): Using vrefresh ranges from config file
[ 12.407] (II) intel(0): Printing DDC gathered Modelines:
[ 12.407] (II) intel(0): Modeline "1920x1080i"x0.0 74.25 1920 2448 2492 2640 1080 1084 1094 1125 interlace +hsync +vsync (28.1 kHz)
[ 12.407] (II) intel(0): Modeline "1280x720"x0.0 74.25 1280 1720 1760 1980 720 725 730 750 +hsync +vsync (37.5 kHz)
[ 13.075] (II) intel(0): EDID vendor "TSB", prod id 259
[ 13.075] (II) intel(0): Using hsync ranges from config file
[ 13.075] (II) intel(0): Using vrefresh ranges from config file
[ 13.075] (II) intel(0): Printing DDC gathered Modelines:
[ 13.075] (II) intel(0): Modeline "1920x1080i"x0.0 74.25 1920 2448 2492 2640 1080 1084 1094 1125 interlace +hsync +vsync (28.1 kHz)
[ 13.075] (II) intel(0): Modeline "1280x720"x0.0 74.25 1280 1720 1760 1980 720 725 730 750 +hsync +vsync (37.5 kHz)
[ 14.138] (II) intel(0): EDID vendor "TSB", prod id 259
[ 14.138] (II) intel(0): Using hsync ranges from config file
[ 14.138] (II) intel(0): Using vrefresh ranges from config file
[ 14.138] (II) intel(0): Printing DDC gathered Modelines:
[ 14.138] (II) intel(0): Modeline "1920x1080i"x0.0 74.25 1920 2448 2492 2640 1080 1084 1094 1125 interlace +hsync +vsync (28.1 kHz)
[ 14.138] (II) intel(0): Modeline "1280x720"x0.0 74.25 1280 1720 1760 1980 720 725 730 750 +hsync +vsync (37.5 kHz)
[ 19.722] (II) intel(0): EDID vendor "TSB", prod id 259
[ 19.722] (II) intel(0): Using hsync ranges from config file
[ 19.722] (II) intel(0): Using vrefresh ranges from config file
[ 19.722] (II) intel(0): Printing DDC gathered Modelines:
[ 19.723] (II) intel(0): Modeline "1920x1080i"x0.0 74.25 1920 2448 2492 2640 1080 1084 1094 1125 interlace +hsync +vsync (28.1 kHz)
[ 19.723] (II) intel(0): Modeline "1280x720"x0.0 74.25 1280 1720 1760 1980 720 725 730 750 +hsync +vsync (37.5 kHz)
[ 311.328] (II) intel(0): EDID vendor "TSB", prod id 259
[ 311.328] (II) intel(0): Using hsync ranges from config file
[ 311.328] (II) intel(0): Using vrefresh ranges from config file
[ 311.328] (II) intel(0): Printing DDC gathered Modelines:
[ 311.328] (II) intel(0): Modeline "1920x1080i"x0.0 74.25 1920 2448 2492 2640 1080 1084 1094 1125 interlace +hsync +vsync (28.1 kHz)
[ 311.328] (II) intel(0): Modeline "1280x720"x0.0 74.25 1280 1720 1760 1980 720 725 730 750 +hsync +vsync (37.5 kHz)
[-- Attachment #3: Xorg-noTV.0.log --]
[-- Type: application/octet-stream, Size: 43850 bytes --]
[ 18.467]
X.Org X Server 1.8.1
Release Date: 2010-05-11
[ 18.467] X Protocol Version 11, Revision 0
[ 18.467] Build Operating System: Linux 2.6.24-27-xen x86_64 Ubuntu
[ 18.467] Current Operating System: Linux HTPC 2.6.33-02063304-generic #02063304 SMP Mon May 17 13:10:58 UTC 2010 x86_64
[ 18.467] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-2.6.33-02063304-generic root=UUID=9eeb3950-8050-485a-a6ad-903560e55adc ro vga=794 quiet splash
[ 18.467] Build Date: 21 May 2010 04:30:29PM
[ 18.467] xorg-server 2:1.8.1+git20100521+server-1.8-branch.a8de0866-0ubuntu0sarvatt~lucid (Robert Hooker <sarvatt@ubuntu.com>)
[ 18.467] Current version of pixman: 0.19.1
[ 18.467] Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
[ 18.467] Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[ 18.467] (==) Log file: "/var/log/Xorg.0.log", Time: Mon May 31 15:50:46 2010
[ 18.467] (==) Using config file: "/etc/X11/xorg.conf"
[ 18.467] (==) Using system config directory "/usr/share/X11/xorg.conf.d"
[ 18.467] (==) ServerLayout "Default Layout"
[ 18.467] (**) |-->Screen "TV" (0)
[ 18.467] (**) | |-->Monitor "TSB-TV"
[ 18.467] (**) | |-->Device "Intel HD Graphics"
[ 18.467] (==) Automatically adding devices
[ 18.467] (==) Automatically enabling devices
[ 18.467] (WW) The directory "/usr/share/fonts/X11/cyrillic" does not exist.
[ 18.467] Entry deleted from font path.
[ 18.467] (==) FontPath set to:
/usr/share/fonts/X11/misc,
/usr/share/fonts/X11/100dpi/:unscaled,
/usr/share/fonts/X11/75dpi/:unscaled,
/usr/share/fonts/X11/Type1,
/usr/share/fonts/X11/100dpi,
/usr/share/fonts/X11/75dpi,
/var/lib/defoma/x-ttcidfont-conf.d/dirs/TrueType,
built-ins
[ 18.467] (==) ModulePath set to "/usr/lib/xorg/extra-modules,/usr/lib/xorg/modules"
[ 18.467] (II) The server relies on udev to provide the list of input devices.
If no devices become available, reconfigure udev or disable AutoAddDevices.
[ 18.467] (II) Loader magic: 0x7ce8c0
[ 18.467] (II) Module ABI versions:
[ 18.467] X.Org ANSI C Emulation: 0.4
[ 18.467] X.Org Video Driver: 7.0
[ 18.467] X.Org XInput driver : 9.0
[ 18.467] X.Org Server Extension : 3.0
[ 18.492] (--) PCI:*(0:0:2:0) 8086:0042:1458:d000 Intel Corporation Core Processor Integrated Graphics Controller rev 18, Mem @ 0xfb400000/4194304, 0xe0000000/268435456, I/O @ 0x0000ff00/8
[ 18.492] (II) Open ACPI successful (/var/run/acpid.socket)
[ 18.492] (II) LoadModule: "extmod"
[ 18.492] (II) Loading /usr/lib/xorg/modules/extensions/libextmod.so
[ 18.492] (II) Module extmod: vendor="X.Org Foundation"
[ 18.492] compiled for 1.8.1, module version = 1.0.0
[ 18.492] Module class: X.Org Server Extension
[ 18.492] ABI class: X.Org Server Extension, version 3.0
[ 18.492] (II) Loading extension MIT-SCREEN-SAVER
[ 18.492] (II) Loading extension XFree86-VidModeExtension
[ 18.492] (II) Loading extension XFree86-DGA
[ 18.492] (II) Loading extension DPMS
[ 18.492] (II) Loading extension XVideo
[ 18.493] (II) Loading extension XVideo-MotionCompensation
[ 18.493] (II) Loading extension X-Resource
[ 18.493] (II) LoadModule: "dbe"
[ 18.493] (II) Loading /usr/lib/xorg/modules/extensions/libdbe.so
[ 18.493] (II) Module dbe: vendor="X.Org Foundation"
[ 18.493] compiled for 1.8.1, module version = 1.0.0
[ 18.493] Module class: X.Org Server Extension
[ 18.493] ABI class: X.Org Server Extension, version 3.0
[ 18.493] (II) Loading extension DOUBLE-BUFFER
[ 18.493] (II) LoadModule: "glx"
[ 18.493] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[ 18.493] (II) Module glx: vendor="X.Org Foundation"
[ 18.493] compiled for 1.8.1, module version = 1.0.0
[ 18.493] ABI class: X.Org Server Extension, version 3.0
[ 18.493] (==) AIGLX enabled
[ 18.493] (II) Loading extension GLX
[ 18.493] (II) LoadModule: "record"
[ 18.493] (II) Loading /usr/lib/xorg/modules/extensions/librecord.so
[ 18.493] (II) Module record: vendor="X.Org Foundation"
[ 18.493] compiled for 1.8.1, module version = 1.13.0
[ 18.493] Module class: X.Org Server Extension
[ 18.493] ABI class: X.Org Server Extension, version 3.0
[ 18.493] (II) Loading extension RECORD
[ 18.493] (II) LoadModule: "dri"
[ 18.493] (II) Loading /usr/lib/xorg/modules/extensions/libdri.so
[ 18.493] (II) Module dri: vendor="X.Org Foundation"
[ 18.493] compiled for 1.8.1, module version = 1.0.0
[ 18.493] ABI class: X.Org Server Extension, version 3.0
[ 18.493] (II) Loading extension XFree86-DRI
[ 18.493] (II) LoadModule: "dri2"
[ 18.493] (II) Loading /usr/lib/xorg/modules/extensions/libdri2.so
[ 18.494] (II) Module dri2: vendor="X.Org Foundation"
[ 18.494] compiled for 1.8.1, module version = 1.2.0
[ 18.494] ABI class: X.Org Server Extension, version 3.0
[ 18.494] (II) Loading extension DRI2
[ 18.494] (II) LoadModule: "intel"
[ 18.494] (II) Loading /usr/lib/xorg/modules/drivers/intel_drv.so
[ 18.494] (II) Module intel: vendor="X.Org Foundation"
[ 18.494] compiled for 1.8.1, module version = 2.11.0
[ 18.494] Module class: X.Org Video Driver
[ 18.494] ABI class: X.Org Video Driver, version 7.0
[ 18.494] (II) intel: Driver for Intel Integrated Graphics Chipsets: i810,
i810-dc100, i810e, i815, i830M, 845G, 852GM/855GM, 865G, 915G,
E7221 (i915), 915GM, 945G, 945GM, 945GME, Pineview GM, Pineview G,
965G, G35, 965Q, 946GZ, 965GM, 965GME/GLE, G33, Q35, Q33, GM45,
4 Series, G45/G43, Q45/Q43, G41, B43, Clarkdale, Arrandale
[ 18.494] (--) using VT number 1
[ 18.494] (II) Primary Device is: PCI 00@00:02:0
[ 18.496] drmOpenDevice: node name is /dev/dri/card0
[ 18.496] drmOpenDevice: open result is 9, (OK)
[ 18.496] drmOpenByBusid: Searching for BusID pci:0000:00:02.0
[ 18.496] drmOpenDevice: node name is /dev/dri/card0
[ 18.496] drmOpenDevice: open result is 9, (OK)
[ 18.496] drmOpenByBusid: drmOpenMinor returns 9
[ 18.496] drmOpenByBusid: drmGetBusid reports pci:0000:00:02.0
[ 18.496] (**) intel(0): Depth 24, (--) framebuffer bpp 32
[ 18.496] (==) intel(0): RGB weight 888
[ 18.496] (==) intel(0): Default visual is TrueColor
[ 18.496] (II) intel(0): Integrated Graphics Chipset: Intel(R) Clarkdale
[ 18.496] (--) intel(0): Chipset: "Clarkdale"
[ 18.496] (==) intel(0): video overlay key set to 0x101fe
[ 18.513] (II) intel(0): Output VGA1 using monitor section TSB-TV
[ 18.513] (**) intel(0): Option "PreferredMode" "1920x1080i"
[ 18.513] (**) intel(0): Option "Enable" "true"
[ 18.522] (II) intel(0): Output HDMI1 has no monitor section
[ 18.527] (II) intel(0): Output DP1 has no monitor section
[ 18.536] (II) intel(0): Output HDMI2 using monitor section TSB-TV
[ 18.545] (II) intel(0): Output HDMI3 has no monitor section
[ 18.550] (II) intel(0): Output DP2 has no monitor section
[ 18.555] (II) intel(0): Output DP3 has no monitor section
[ 18.572] (II) intel(0): EDID for output VGA1
[ 18.572] (II) intel(0): Not using mode "1920x1080i" (interlace mode not supported)
[ 18.572] (II) intel(0): Not using mode "1920x1080_30.00" (vrefresh out of range)
[ 18.572] (II) intel(0): Not using mode "1920x1080i_30.00" (interlace mode not supported)
[ 18.572] (II) intel(0): Not using mode "1920x1080i_28.00" (interlace mode not supported)
[ 18.572] (II) intel(0): Not using mode "1920x1080_28.00" (vrefresh out of range)
[ 18.572] (II) intel(0): Not using default mode "320x175" (doublescan mode not supported)
[ 18.572] (II) intel(0): Not using default mode "320x200" (doublescan mode not supported)
[ 18.572] (II) intel(0): Not using default mode "360x200" (doublescan mode not supported)
[ 18.572] (II) intel(0): Not using default mode "320x240" (doublescan mode not supported)
[ 18.572] (II) intel(0): Not using default mode "320x240" (doublescan mode not supported)
[ 18.572] (II) intel(0): Not using default mode "320x240" (doublescan mode not supported)
[ 18.572] (II) intel(0): Not using default mode "320x240" (doublescan mode not supported)
[ 18.572] (II) intel(0): Not using default mode "400x300" (doublescan mode not supported)
[ 18.572] (II) intel(0): Not using default mode "400x300" (doublescan mode not supported)
[ 18.572] (II) intel(0): Not using default mode "800x600" (hsync out of range)
[ 18.572] (II) intel(0): Not using default mode "400x300" (doublescan mode not supported)
[ 18.572] (II) intel(0): Not using default mode "800x600" (hsync out of range)
[ 18.572] (II) intel(0): Not using default mode "400x300" (doublescan mode not supported)
[ 18.572] (II) intel(0): Not using default mode "800x600" (hsync out of range)
[ 18.572] (II) intel(0): Not using default mode "400x300" (doublescan mode not supported)
[ 18.572] (II) intel(0): Not using default mode "1024x768i" (interlace mode not supported)
[ 18.572] (II) intel(0): Not using default mode "512x384i" (doublescan mode not supported)
[ 18.572] (II) intel(0): Not using default mode "1024x768" (hsync out of range)
[ 18.572] (II) intel(0): Not using default mode "512x384" (doublescan mode not supported)
[ 18.572] (II) intel(0): Not using default mode "1024x768" (hsync out of range)
[ 18.572] (II) intel(0): Not using default mode "512x384" (doublescan mode not supported)
[ 18.572] (II) intel(0): Not using default mode "1024x768" (hsync out of range)
[ 18.572] (II) intel(0): Not using default mode "512x384" (doublescan mode not supported)
[ 18.572] (II) intel(0): Not using default mode "1024x768" (hsync out of range)
[ 18.572] (II) intel(0): Not using default mode "512x384" (doublescan mode not supported)
[ 18.572] (II) intel(0): Not using default mode "1152x864" (hsync out of range)
[ 18.572] (II) intel(0): Not using default mode "576x432" (doublescan mode not supported)
[ 18.572] (II) intel(0): Not using default mode "1280x960" (hsync out of range)
[ 18.572] (II) intel(0): Not using default mode "640x480" (doublescan mode not supported)
[ 18.572] (II) intel(0): Not using default mode "1280x960" (hsync out of range)
[ 18.572] (II) intel(0): Not using default mode "640x480" (doublescan mode not supported)
[ 18.572] (II) intel(0): Not using default mode "1280x1024" (hsync out of range)
[ 18.572] (II) intel(0): Not using default mode "640x512" (doublescan mode not supported)
[ 18.572] (II) intel(0): Not using default mode "1280x1024" (hsync out of range)
[ 18.572] (II) intel(0): Not using default mode "640x512" (doublescan mode not supported)
[ 18.572] (II) intel(0): Not using default mode "1280x1024" (hsync out of range)
[ 18.572] (II) intel(0): Not using default mode "640x512" (doublescan mode not supported)
[ 18.572] (II) intel(0): Not using default mode "1600x1200" (hsync out of range)
[ 18.572] (II) intel(0): Not using default mode "800x600" (doublescan mode not supported)
[ 18.572] (II) intel(0): Not using default mode "1600x1200" (hsync out of range)
[ 18.572] (II) intel(0): Not using default mode "800x600" (doublescan mode not supported)
[ 18.572] (II) intel(0): Not using default mode "1600x1200" (hsync out of range)
[ 18.572] (II) intel(0): Not using default mode "800x600" (doublescan mode not supported)
[ 18.572] (II) intel(0): Not using default mode "1600x1200" (hsync out of range)
[ 18.572] (II) intel(0): Not using default mode "800x600" (doublescan mode not supported)
[ 18.572] (II) intel(0): Not using default mode "1600x1200" (hsync out of range)
[ 18.572] (II) intel(0): Not using default mode "800x600" (doublescan mode not supported)
[ 18.572] (II) intel(0): Not using default mode "1792x1344" (hsync out of range)
[ 18.572] (II) intel(0): Not using default mode "896x672" (doublescan mode not supported)
[ 18.572] (II) intel(0): Not using default mode "1792x1344" (hsync out of range)
[ 18.572] (II) intel(0): Not using default mode "896x672" (doublescan mode not supported)
[ 18.572] (II) intel(0): Not using default mode "1856x1392" (hsync out of range)
[ 18.572] (II) intel(0): Not using default mode "928x696" (doublescan mode not supported)
[ 18.572] (II) intel(0): Not using default mode "1856x1392" (hsync out of range)
[ 18.572] (II) intel(0): Not using default mode "928x696" (doublescan mode not supported)
[ 18.572] (II) intel(0): Not using default mode "1920x1440" (hsync out of range)
[ 18.572] (II) intel(0): Not using default mode "960x720" (doublescan mode not supported)
[ 18.572] (II) intel(0): Not using default mode "1920x1440" (hsync out of range)
[ 18.572] (II) intel(0): Not using default mode "960x720" (doublescan mode not supported)
[ 18.572] (II) intel(0): Not using default mode "832x624" (hsync out of range)
[ 18.572] (II) intel(0): Not using default mode "416x312" (doublescan mode not supported)
[ 18.572] (II) intel(0): Not using default mode "1152x864" (hsync out of range)
[ 18.572] (II) intel(0): Not using default mode "576x432" (doublescan mode not supported)
[ 18.572] (II) intel(0): Not using default mode "1152x864" (hsync out of range)
[ 18.572] (II) intel(0): Not using default mode "576x432" (doublescan mode not supported)
[ 18.572] (II) intel(0): Not using default mode "1152x864" (hsync out of range)
[ 18.572] (II) intel(0): Not using default mode "576x432" (doublescan mode not supported)
[ 18.572] (II) intel(0): Not using default mode "1152x864" (hsync out of range)
[ 18.572] (II) intel(0): Not using default mode "576x432" (doublescan mode not supported)
[ 18.572] (II) intel(0): Not using default mode "1152x864" (hsync out of range)
[ 18.572] (II) intel(0): Not using default mode "576x432" (doublescan mode not supported)
[ 18.572] (II) intel(0): Not using default mode "1152x864" (hsync out of range)
[ 18.572] (II) intel(0): Not using default mode "576x432" (doublescan mode not supported)
[ 18.572] (II) intel(0): Not using default mode "1360x768" (hsync out of range)
[ 18.572] (II) intel(0): Not using default mode "680x384" (doublescan mode not supported)
[ 18.572] (II) intel(0): Not using default mode "1360x768" (hsync out of range)
[ 18.572] (II) intel(0): Not using default mode "680x384" (doublescan mode not supported)
[ 18.572] (II) intel(0): Not using default mode "1400x1050" (hsync out of range)
[ 18.572] (II) intel(0): Not using default mode "700x525" (doublescan mode not supported)
[ 18.572] (II) intel(0): Not using default mode "1400x1050" (hsync out of range)
[ 18.572] (II) intel(0): Not using default mode "700x525" (doublescan mode not supported)
[ 18.572] (II) intel(0): Not using default mode "1400x1050" (hsync out of range)
[ 18.572] (II) intel(0): Not using default mode "700x525" (doublescan mode not supported)
[ 18.572] (II) intel(0): Not using default mode "1400x1050" (hsync out of range)
[ 18.572] (II) intel(0): Not using default mode "700x525" (doublescan mode not supported)
[ 18.572] (II) intel(0): Not using default mode "1440x900" (hsync out of range)
[ 18.572] (II) intel(0): Not using default mode "720x450" (doublescan mode not supported)
[ 18.572] (II) intel(0): Not using default mode "1600x1024" (hsync out of range)
[ 18.572] (II) intel(0): Not using default mode "800x512" (doublescan mode not supported)
[ 18.572] (II) intel(0): Not using default mode "1680x1050" (hsync out of range)
[ 18.572] (II) intel(0): Not using default mode "840x525" (doublescan mode not supported)
[ 18.572] (II) intel(0): Not using default mode "1680x1050" (hsync out of range)
[ 18.572] (II) intel(0): Not using default mode "840x525" (doublescan mode not supported)
[ 18.572] (II) intel(0): Not using default mode "1680x1050" (hsync out of range)
[ 18.572] (II) intel(0): Not using default mode "840x525" (doublescan mode not supported)
[ 18.572] (II) intel(0): Not using default mode "1680x1050" (hsync out of range)
[ 18.572] (II) intel(0): Not using default mode "840x525" (doublescan mode not supported)
[ 18.572] (II) intel(0): Not using default mode "1680x1050" (hsync out of range)
[ 18.572] (II) intel(0): Not using default mode "840x525" (doublescan mode not supported)
[ 18.572] (II) intel(0): Not using default mode "1920x1080" (hsync out of range)
[ 18.572] (II) intel(0): Not using default mode "960x540" (doublescan mode not supported)
[ 18.572] (II) intel(0): Not using default mode "1920x1200" (hsync out of range)
[ 18.572] (II) intel(0): Not using default mode "960x600" (doublescan mode not supported)
[ 18.572] (II) intel(0): Not using default mode "1920x1440" (hsync out of range)
[ 18.572] (II) intel(0): Not using default mode "960x720" (doublescan mode not supported)
[ 18.572] (II) intel(0): Not using default mode "2048x1536" (hsync out of range)
[ 18.572] (II) intel(0): Not using default mode "1024x768" (doublescan mode not supported)
[ 18.572] (II) intel(0): Not using default mode "2048x1536" (hsync out of range)
[ 18.572] (II) intel(0): Not using default mode "1024x768" (doublescan mode not supported)
[ 18.572] (II) intel(0): Not using default mode "2048x1536" (hsync out of range)
[ 18.572] (II) intel(0): Not using default mode "1024x768" (doublescan mode not supported)
[ 18.572] (II) intel(0): Printing probed modes for output VGA1
[ 18.572] (II) intel(0): Modeline "1280x720_50.0"x50.0 74.25 1280 1720 1760 1980 720 725 730 750 +hsync +vsync (37.5 kHz)
[ 18.572] (II) intel(0): Modeline "800x600"x60.3 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz)
[ 18.572] (II) intel(0): Modeline "800x600"x56.2 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz)
[ 18.572] (II) intel(0): Modeline "640x480"x85.0 36.00 640 696 752 832 480 481 484 509 -hsync -vsync (43.3 kHz)
[ 18.572] (II) intel(0): Modeline "640x480"x72.8 31.50 640 664 704 832 480 489 492 520 -hsync -vsync (37.9 kHz)
[ 18.572] (II) intel(0): Modeline "640x480"x75.0 31.50 640 656 720 840 480 481 484 500 -hsync -vsync (37.5 kHz)
[ 18.572] (II) intel(0): Modeline "640x480"x59.9 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz)
[ 18.572] (II) intel(0): Modeline "720x400"x85.0 35.50 720 756 828 936 400 401 404 446 -hsync +vsync (37.9 kHz)
[ 18.572] (II) intel(0): Modeline "640x400"x85.1 31.50 640 672 736 832 400 401 404 445 -hsync +vsync (37.9 kHz)
[ 18.572] (II) intel(0): Modeline "640x350"x85.1 31.50 640 672 736 832 350 382 385 445 +hsync -vsync (37.9 kHz)
[ 18.582] (II) intel(0): EDID for output HDMI1
[ 18.587] (II) intel(0): EDID for output DP1
[ 18.596] (II) intel(0): EDID for output HDMI2
[ 18.596] (II) intel(0): Not using mode "1920x1080i" (interlace mode not supported)
[ 18.596] (II) intel(0): Not using mode "1920x1080_30.00" (vrefresh out of range)
[ 18.596] (II) intel(0): Not using mode "1920x1080i_30.00" (interlace mode not supported)
[ 18.596] (II) intel(0): Not using mode "1920x1080i_28.00" (interlace mode not supported)
[ 18.596] (II) intel(0): Not using mode "1920x1080_28.00" (vrefresh out of range)
[ 18.596] (II) intel(0): Not using default mode "320x175" (doublescan mode not supported)
[ 18.596] (II) intel(0): Not using default mode "320x200" (doublescan mode not supported)
[ 18.596] (II) intel(0): Not using default mode "360x200" (doublescan mode not supported)
[ 18.596] (II) intel(0): Not using default mode "320x240" (doublescan mode not supported)
[ 18.596] (II) intel(0): Not using default mode "320x240" (doublescan mode not supported)
[ 18.596] (II) intel(0): Not using default mode "320x240" (doublescan mode not supported)
[ 18.596] (II) intel(0): Not using default mode "320x240" (doublescan mode not supported)
[ 18.596] (II) intel(0): Not using default mode "400x300" (doublescan mode not supported)
[ 18.596] (II) intel(0): Not using default mode "400x300" (doublescan mode not supported)
[ 18.596] (II) intel(0): Not using default mode "800x600" (hsync out of range)
[ 18.596] (II) intel(0): Not using default mode "400x300" (doublescan mode not supported)
[ 18.596] (II) intel(0): Not using default mode "800x600" (hsync out of range)
[ 18.596] (II) intel(0): Not using default mode "400x300" (doublescan mode not supported)
[ 18.596] (II) intel(0): Not using default mode "800x600" (hsync out of range)
[ 18.596] (II) intel(0): Not using default mode "400x300" (doublescan mode not supported)
[ 18.596] (II) intel(0): Not using default mode "1024x768i" (interlace mode not supported)
[ 18.596] (II) intel(0): Not using default mode "512x384i" (doublescan mode not supported)
[ 18.596] (II) intel(0): Not using default mode "1024x768" (hsync out of range)
[ 18.596] (II) intel(0): Not using default mode "512x384" (doublescan mode not supported)
[ 18.596] (II) intel(0): Not using default mode "1024x768" (hsync out of range)
[ 18.596] (II) intel(0): Not using default mode "512x384" (doublescan mode not supported)
[ 18.596] (II) intel(0): Not using default mode "1024x768" (hsync out of range)
[ 18.596] (II) intel(0): Not using default mode "512x384" (doublescan mode not supported)
[ 18.596] (II) intel(0): Not using default mode "1024x768" (hsync out of range)
[ 18.596] (II) intel(0): Not using default mode "512x384" (doublescan mode not supported)
[ 18.596] (II) intel(0): Not using default mode "1152x864" (hsync out of range)
[ 18.596] (II) intel(0): Not using default mode "576x432" (doublescan mode not supported)
[ 18.596] (II) intel(0): Not using default mode "1280x960" (hsync out of range)
[ 18.596] (II) intel(0): Not using default mode "640x480" (doublescan mode not supported)
[ 18.596] (II) intel(0): Not using default mode "1280x960" (hsync out of range)
[ 18.596] (II) intel(0): Not using default mode "640x480" (doublescan mode not supported)
[ 18.596] (II) intel(0): Not using default mode "1280x1024" (hsync out of range)
[ 18.596] (II) intel(0): Not using default mode "640x512" (doublescan mode not supported)
[ 18.596] (II) intel(0): Not using default mode "1280x1024" (hsync out of range)
[ 18.596] (II) intel(0): Not using default mode "640x512" (doublescan mode not supported)
[ 18.596] (II) intel(0): Not using default mode "1280x1024" (hsync out of range)
[ 18.596] (II) intel(0): Not using default mode "640x512" (doublescan mode not supported)
[ 18.596] (II) intel(0): Not using default mode "1600x1200" (hsync out of range)
[ 18.596] (II) intel(0): Not using default mode "800x600" (doublescan mode not supported)
[ 18.596] (II) intel(0): Not using default mode "1600x1200" (hsync out of range)
[ 18.596] (II) intel(0): Not using default mode "800x600" (doublescan mode not supported)
[ 18.596] (II) intel(0): Not using default mode "1600x1200" (hsync out of range)
[ 18.596] (II) intel(0): Not using default mode "800x600" (doublescan mode not supported)
[ 18.596] (II) intel(0): Not using default mode "1600x1200" (hsync out of range)
[ 18.596] (II) intel(0): Not using default mode "800x600" (doublescan mode not supported)
[ 18.596] (II) intel(0): Not using default mode "1600x1200" (hsync out of range)
[ 18.597] (II) intel(0): Not using default mode "800x600" (doublescan mode not supported)
[ 18.597] (II) intel(0): Not using default mode "1792x1344" (hsync out of range)
[ 18.597] (II) intel(0): Not using default mode "896x672" (doublescan mode not supported)
[ 18.597] (II) intel(0): Not using default mode "1792x1344" (hsync out of range)
[ 18.597] (II) intel(0): Not using default mode "896x672" (doublescan mode not supported)
[ 18.597] (II) intel(0): Not using default mode "1856x1392" (hsync out of range)
[ 18.597] (II) intel(0): Not using default mode "928x696" (doublescan mode not supported)
[ 18.597] (II) intel(0): Not using default mode "1856x1392" (hsync out of range)
[ 18.597] (II) intel(0): Not using default mode "928x696" (doublescan mode not supported)
[ 18.597] (II) intel(0): Not using default mode "1920x1440" (hsync out of range)
[ 18.597] (II) intel(0): Not using default mode "960x720" (doublescan mode not supported)
[ 18.597] (II) intel(0): Not using default mode "1920x1440" (hsync out of range)
[ 18.597] (II) intel(0): Not using default mode "960x720" (doublescan mode not supported)
[ 18.597] (II) intel(0): Not using default mode "832x624" (hsync out of range)
[ 18.597] (II) intel(0): Not using default mode "416x312" (doublescan mode not supported)
[ 18.597] (II) intel(0): Not using default mode "1152x864" (hsync out of range)
[ 18.597] (II) intel(0): Not using default mode "576x432" (doublescan mode not supported)
[ 18.597] (II) intel(0): Not using default mode "1152x864" (hsync out of range)
[ 18.597] (II) intel(0): Not using default mode "576x432" (doublescan mode not supported)
[ 18.597] (II) intel(0): Not using default mode "1152x864" (hsync out of range)
[ 18.597] (II) intel(0): Not using default mode "576x432" (doublescan mode not supported)
[ 18.597] (II) intel(0): Not using default mode "1152x864" (hsync out of range)
[ 18.597] (II) intel(0): Not using default mode "576x432" (doublescan mode not supported)
[ 18.597] (II) intel(0): Not using default mode "1152x864" (hsync out of range)
[ 18.597] (II) intel(0): Not using default mode "576x432" (doublescan mode not supported)
[ 18.597] (II) intel(0): Not using default mode "1152x864" (hsync out of range)
[ 18.597] (II) intel(0): Not using default mode "576x432" (doublescan mode not supported)
[ 18.597] (II) intel(0): Not using default mode "1360x768" (hsync out of range)
[ 18.597] (II) intel(0): Not using default mode "680x384" (doublescan mode not supported)
[ 18.597] (II) intel(0): Not using default mode "1360x768" (hsync out of range)
[ 18.597] (II) intel(0): Not using default mode "680x384" (doublescan mode not supported)
[ 18.597] (II) intel(0): Not using default mode "1400x1050" (hsync out of range)
[ 18.597] (II) intel(0): Not using default mode "700x525" (doublescan mode not supported)
[ 18.597] (II) intel(0): Not using default mode "1400x1050" (hsync out of range)
[ 18.597] (II) intel(0): Not using default mode "700x525" (doublescan mode not supported)
[ 18.597] (II) intel(0): Not using default mode "1400x1050" (hsync out of range)
[ 18.597] (II) intel(0): Not using default mode "700x525" (doublescan mode not supported)
[ 18.597] (II) intel(0): Not using default mode "1400x1050" (hsync out of range)
[ 18.597] (II) intel(0): Not using default mode "700x525" (doublescan mode not supported)
[ 18.597] (II) intel(0): Not using default mode "1440x900" (hsync out of range)
[ 18.597] (II) intel(0): Not using default mode "720x450" (doublescan mode not supported)
[ 18.597] (II) intel(0): Not using default mode "1600x1024" (hsync out of range)
[ 18.597] (II) intel(0): Not using default mode "800x512" (doublescan mode not supported)
[ 18.597] (II) intel(0): Not using default mode "1680x1050" (hsync out of range)
[ 18.597] (II) intel(0): Not using default mode "840x525" (doublescan mode not supported)
[ 18.597] (II) intel(0): Not using default mode "1680x1050" (hsync out of range)
[ 18.597] (II) intel(0): Not using default mode "840x525" (doublescan mode not supported)
[ 18.597] (II) intel(0): Not using default mode "1680x1050" (hsync out of range)
[ 18.597] (II) intel(0): Not using default mode "840x525" (doublescan mode not supported)
[ 18.597] (II) intel(0): Not using default mode "1680x1050" (hsync out of range)
[ 18.597] (II) intel(0): Not using default mode "840x525" (doublescan mode not supported)
[ 18.597] (II) intel(0): Not using default mode "1680x1050" (hsync out of range)
[ 18.597] (II) intel(0): Not using default mode "840x525" (doublescan mode not supported)
[ 18.597] (II) intel(0): Not using default mode "1920x1080" (hsync out of range)
[ 18.597] (II) intel(0): Not using default mode "960x540" (doublescan mode not supported)
[ 18.597] (II) intel(0): Not using default mode "1920x1200" (hsync out of range)
[ 18.597] (II) intel(0): Not using default mode "960x600" (doublescan mode not supported)
[ 18.597] (II) intel(0): Not using default mode "1920x1440" (hsync out of range)
[ 18.597] (II) intel(0): Not using default mode "960x720" (doublescan mode not supported)
[ 18.597] (II) intel(0): Not using default mode "2048x1536" (hsync out of range)
[ 18.597] (II) intel(0): Not using default mode "1024x768" (doublescan mode not supported)
[ 18.597] (II) intel(0): Not using default mode "2048x1536" (hsync out of range)
[ 18.597] (II) intel(0): Not using default mode "1024x768" (doublescan mode not supported)
[ 18.597] (II) intel(0): Not using default mode "2048x1536" (hsync out of range)
[ 18.597] (II) intel(0): Not using default mode "1024x768" (doublescan mode not supported)
[ 18.597] (II) intel(0): Printing probed modes for output HDMI2
[ 18.597] (II) intel(0): Modeline "1280x720_50.0"x50.0 74.25 1280 1720 1760 1980 720 725 730 750 +hsync +vsync (37.5 kHz)
[ 18.597] (II) intel(0): Modeline "800x600"x60.3 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz)
[ 18.597] (II) intel(0): Modeline "800x600"x56.2 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz)
[ 18.597] (II) intel(0): Modeline "640x480"x85.0 36.00 640 696 752 832 480 481 484 509 -hsync -vsync (43.3 kHz)
[ 18.597] (II) intel(0): Modeline "640x480"x72.8 31.50 640 664 704 832 480 489 492 520 -hsync -vsync (37.9 kHz)
[ 18.597] (II) intel(0): Modeline "640x480"x75.0 31.50 640 656 720 840 480 481 484 500 -hsync -vsync (37.5 kHz)
[ 18.597] (II) intel(0): Modeline "640x480"x59.9 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz)
[ 18.597] (II) intel(0): Modeline "720x400"x85.0 35.50 720 756 828 936 400 401 404 446 -hsync +vsync (37.9 kHz)
[ 18.597] (II) intel(0): Modeline "640x400"x85.1 31.50 640 672 736 832 400 401 404 445 -hsync +vsync (37.9 kHz)
[ 18.597] (II) intel(0): Modeline "640x350"x85.1 31.50 640 672 736 832 350 382 385 445 +hsync -vsync (37.9 kHz)
[ 18.606] (II) intel(0): EDID for output HDMI3
[ 18.611] (II) intel(0): EDID for output DP2
[ 18.616] (II) intel(0): EDID for output DP3
[ 18.616] (II) intel(0): Output VGA1 enabled by config file
[ 18.616] (II) intel(0): Output HDMI1 disconnected
[ 18.616] (II) intel(0): Output DP1 disconnected
[ 18.616] (II) intel(0): Output HDMI2 enabled by config file
[ 18.616] (II) intel(0): Output HDMI3 disconnected
[ 18.616] (II) intel(0): Output DP2 disconnected
[ 18.616] (II) intel(0): Output DP3 disconnected
[ 18.616] (II) intel(0): Using fuzzy aspect match for initial modes
[ 18.616] (II) intel(0): Output VGA1 using initial mode 800x600
[ 18.616] (II) intel(0): Output HDMI2 using initial mode 800x600
[ 18.616] (II) intel(0): Using default gamma of (1.0, 1.0, 1.0) unless otherwise stated.
[ 18.616] (II) intel(0): Kernel page flipping support detected, enabling
[ 18.616] (==) intel(0): DPI set to (96, 96)
[ 18.616] (II) Loading sub module "fb"
[ 18.616] (II) LoadModule: "fb"
[ 18.616] (II) Loading /usr/lib/xorg/modules/libfb.so
[ 18.617] (II) Module fb: vendor="X.Org Foundation"
[ 18.617] compiled for 1.8.1, module version = 1.0.0
[ 18.617] ABI class: X.Org ANSI C Emulation, version 0.4
[ 18.617] (==) Depth 24 pixmap format is 32 bpp
[ 18.617] (II) intel(0): [DRI2] Setup complete
[ 18.617] (II) intel(0): [DRI2] DRI driver: i965
[ 18.617] (**) intel(0): Tiling enabled
[ 18.617] (**) intel(0): SwapBuffers wait enabled
[ 18.617] (==) intel(0): VideoRam: 262144 KB
[ 18.617] (II) intel(0): Attempting memory allocation with tiled buffers.
[ 18.617] (II) intel(0): Tiled allocation successful.
[ 18.622] (II) UXA(0): Driver registered support for the following operations:
[ 18.622] (II) solid
[ 18.622] (II) copy
[ 18.622] (II) composite (RENDER acceleration)
[ 18.622] (II) put_image
[ 18.622] (==) intel(0): Backing store disabled
[ 18.622] (==) intel(0): Silken mouse enabled
[ 18.622] (II) intel(0): Initializing HW Cursor
[ 18.806] (II) intel(0): RandR 1.2 enabled, ignore the following RandR disabled message.
[ 18.806] (==) intel(0): DPMS enabled
[ 18.806] (==) intel(0): Intel XvMC decoder enabled
[ 18.806] (II) intel(0): Set up textured video
[ 18.806] (II) intel(0): [XvMC] xvmc_vld driver initialized.
[ 18.806] (II) intel(0): direct rendering: DRI2 Enabled
[ 18.806] (WW) intel(0): Option "ConnectedMonitor" is not used
[ 18.806] (WW) intel(0): Option "CustomEDID" is not used
[ 18.806] (WW) intel(0): Option "Enable" is not used
[ 18.806] (WW) intel(0): Option "PreferredMode" is not used
[ 18.806] (--) RandR disabled
[ 18.806] (II) Initializing built-in extension Generic Event Extension
[ 18.806] (II) Initializing built-in extension SHAPE
[ 18.806] (II) Initializing built-in extension MIT-SHM
[ 18.806] (II) Initializing built-in extension XInputExtension
[ 18.806] (II) Initializing built-in extension XTEST
[ 18.806] (II) Initializing built-in extension BIG-REQUESTS
[ 18.806] (II) Initializing built-in extension SYNC
[ 18.806] (II) Initializing built-in extension XKEYBOARD
[ 18.806] (II) Initializing built-in extension XC-MISC
[ 18.806] (II) Initializing built-in extension SECURITY
[ 18.806] (II) Initializing built-in extension XINERAMA
[ 18.806] (II) Initializing built-in extension XFIXES
[ 18.806] (II) Initializing built-in extension RENDER
[ 18.806] (II) Initializing built-in extension RANDR
[ 18.806] (II) Initializing built-in extension COMPOSITE
[ 18.806] (II) Initializing built-in extension DAMAGE
[ 18.811] (II) AIGLX: enabled GLX_MESA_copy_sub_buffer
[ 18.811] (II) AIGLX: enabled GLX_INTEL_swap_event
[ 18.811] (II) AIGLX: enabled GLX_SGI_swap_control and GLX_MESA_swap_control
[ 18.811] (II) AIGLX: enabled GLX_SGI_make_current_read
[ 18.811] (II) AIGLX: GLX_EXT_texture_from_pixmap backed by buffer objects
[ 18.811] (II) AIGLX: Loaded and initialized /usr/lib/dri/i965_dri.so
[ 18.811] (II) GLX: Initialized DRI2 GL provider for screen 0
[ 18.811] (II) intel(0): Setting screen physical size to 211 x 158
[ 18.844] (II) config/udev: Adding input device Power Button (/dev/input/event1)
[ 18.844] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[ 18.844] (II) LoadModule: "evdev"
[ 18.844] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 18.844] (II) Module evdev: vendor="X.Org Foundation"
[ 18.844] compiled for 1.8.0.902, module version = 2.4.0
[ 18.844] Module class: X.Org XInput Driver
[ 18.844] ABI class: X.Org XInput driver, version 9.0
[ 18.844] (**) Power Button: always reports core events
[ 18.844] (**) Power Button: Device: "/dev/input/event1"
[ 18.900] (--) Power Button: Found keys
[ 18.900] (II) Power Button: Configuring as keyboard
[ 18.900] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD)
[ 18.900] (**) Option "xkb_rules" "evdev"
[ 18.900] (**) Option "xkb_model" "pc105"
[ 18.900] (**) Option "xkb_layout" "fr"
[ 18.900] (**) Option "xkb_variant" "oss"
[ 18.920] (II) config/udev: Adding input device Power Button (/dev/input/event0)
[ 18.920] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[ 18.920] (**) Power Button: always reports core events
[ 18.920] (**) Power Button: Device: "/dev/input/event0"
[ 18.960] (--) Power Button: Found keys
[ 18.960] (II) Power Button: Configuring as keyboard
[ 18.960] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD)
[ 18.960] (**) Option "xkb_rules" "evdev"
[ 18.960] (**) Option "xkb_model" "pc105"
[ 18.960] (**) Option "xkb_layout" "fr"
[ 18.960] (**) Option "xkb_variant" "oss"
[ 18.962] (II) config/udev: Adding input device HDA Digital PCBeep (/dev/input/event5)
[ 18.962] (II) No input driver/identifier specified (ignoring)
[ 18.963] (II) config/udev: Adding input device Kensington Kensington Ci75m Wireless Notebook Mouse (/dev/input/event3)
[ 18.963] (**) Kensington Kensington Ci75m Wireless Notebook Mouse: Applying InputClass "evdev pointer catchall"
[ 18.963] (**) Kensington Kensington Ci75m Wireless Notebook Mouse: always reports core events
[ 18.963] (**) Kensington Kensington Ci75m Wireless Notebook Mouse: Device: "/dev/input/event3"
[ 19.050] (--) Kensington Kensington Ci75m Wireless Notebook Mouse: Found 3 mouse buttons
[ 19.050] (--) Kensington Kensington Ci75m Wireless Notebook Mouse: Found scroll wheel(s)
[ 19.050] (--) Kensington Kensington Ci75m Wireless Notebook Mouse: Found relative axes
[ 19.050] (--) Kensington Kensington Ci75m Wireless Notebook Mouse: Found x and y relative axes
[ 19.050] (II) Kensington Kensington Ci75m Wireless Notebook Mouse: Configuring as mouse
[ 19.050] (**) Kensington Kensington Ci75m Wireless Notebook Mouse: YAxisMapping: buttons 4 and 5
[ 19.050] (**) Kensington Kensington Ci75m Wireless Notebook Mouse: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[ 19.050] (II) XINPUT: Adding extended input device "Kensington Kensington Ci75m Wireless Notebook Mouse" (type: MOUSE)
[ 19.050] (**) Kensington Kensington Ci75m Wireless Notebook Mouse: (accel) keeping acceleration scheme 1
[ 19.050] (**) Kensington Kensington Ci75m Wireless Notebook Mouse: (accel) acceleration profile 0
[ 19.050] (**) Kensington Kensington Ci75m Wireless Notebook Mouse: (accel) acceleration factor: 2.000
[ 19.050] (**) Kensington Kensington Ci75m Wireless Notebook Mouse: (accel) acceleration threshold: 4
[ 19.050] (II) Kensington Kensington Ci75m Wireless Notebook Mouse: initialized for relative axes.
[ 19.050] (II) config/udev: Adding input device Kensington Kensington Ci75m Wireless Notebook Mouse (/dev/input/mouse1)
[ 19.050] (II) No input driver/identifier specified (ignoring)
[ 19.051] (II) config/udev: Adding input device iMON PAD IR Mouse (15c2:0038) (/dev/input/event4)
[ 19.051] (**) iMON PAD IR Mouse (15c2:0038): Applying InputClass "evdev pointer catchall"
[ 19.051] (**) iMON PAD IR Mouse (15c2:0038): always reports core events
[ 19.051] (**) iMON PAD IR Mouse (15c2:0038): Device: "/dev/input/event4"
[ 19.170] (--) iMON PAD IR Mouse (15c2:0038): Found 9 mouse buttons
[ 19.170] (--) iMON PAD IR Mouse (15c2:0038): Found scroll wheel(s)
[ 19.170] (--) iMON PAD IR Mouse (15c2:0038): Found relative axes
[ 19.170] (--) iMON PAD IR Mouse (15c2:0038): Found x and y relative axes
[ 19.170] (II) iMON PAD IR Mouse (15c2:0038): Configuring as mouse
[ 19.170] (**) iMON PAD IR Mouse (15c2:0038): YAxisMapping: buttons 4 and 5
[ 19.170] (**) iMON PAD IR Mouse (15c2:0038): EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[ 19.170] (II) XINPUT: Adding extended input device "iMON PAD IR Mouse (15c2:0038)" (type: MOUSE)
[ 19.170] (**) iMON PAD IR Mouse (15c2:0038): (accel) keeping acceleration scheme 1
[ 19.170] (**) iMON PAD IR Mouse (15c2:0038): (accel) acceleration profile 0
[ 19.170] (**) iMON PAD IR Mouse (15c2:0038): (accel) acceleration factor: 2.000
[ 19.170] (**) iMON PAD IR Mouse (15c2:0038): (accel) acceleration threshold: 4
[ 19.170] (II) iMON PAD IR Mouse (15c2:0038): initialized for relative axes.
[ 19.170] (II) config/udev: Adding input device iMON PAD IR Mouse (15c2:0038) (/dev/input/mouse2)
[ 19.170] (II) No input driver/identifier specified (ignoring)
[ 19.172] (II) config/udev: Adding input device IR-receiver inside an USB DVB receiver (/dev/input/event6)
[ 19.172] (**) IR-receiver inside an USB DVB receiver: Applying InputClass "evdev keyboard catchall"
[ 19.172] (**) IR-receiver inside an USB DVB receiver: always reports core events
[ 19.172] (**) IR-receiver inside an USB DVB receiver: Device: "/dev/input/event6"
[ 19.210] (--) IR-receiver inside an USB DVB receiver: Found keys
[ 19.210] (II) IR-receiver inside an USB DVB receiver: Configuring as keyboard
[ 19.210] (II) XINPUT: Adding extended input device "IR-receiver inside an USB DVB receiver" (type: KEYBOARD)
[ 19.210] (**) Option "xkb_rules" "evdev"
[ 19.210] (**) Option "xkb_model" "pc105"
[ 19.210] (**) Option "xkb_layout" "fr"
[ 19.210] (**) Option "xkb_variant" "oss"
[ 19.215] (II) config/udev: Adding input device Macintosh mouse button emulation (/dev/input/event2)
[ 19.215] (**) Macintosh mouse button emulation: Applying InputClass "evdev pointer catchall"
[ 19.215] (**) Macintosh mouse button emulation: always reports core events
[ 19.215] (**) Macintosh mouse button emulation: Device: "/dev/input/event2"
[ 19.280] (--) Macintosh mouse button emulation: Found 3 mouse buttons
[ 19.280] (--) Macintosh mouse button emulation: Found relative axes
[ 19.280] (--) Macintosh mouse button emulation: Found x and y relative axes
[ 19.280] (II) Macintosh mouse button emulation: Configuring as mouse
[ 19.280] (**) Macintosh mouse button emulation: YAxisMapping: buttons 4 and 5
[ 19.280] (**) Macintosh mouse button emulation: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[ 19.280] (II) XINPUT: Adding extended input device "Macintosh mouse button emulation" (type: MOUSE)
[ 19.280] (**) Macintosh mouse button emulation: (accel) keeping acceleration scheme 1
[ 19.280] (**) Macintosh mouse button emulation: (accel) acceleration profile 0
[ 19.280] (**) Macintosh mouse button emulation: (accel) acceleration factor: 2.000
[ 19.280] (**) Macintosh mouse button emulation: (accel) acceleration threshold: 4
[ 19.280] (II) Macintosh mouse button emulation: initialized for relative axes.
[ 19.280] (II) config/udev: Adding input device Macintosh mouse button emulation (/dev/input/mouse0)
[ 19.280] (II) No input driver/identifier specified (ignoring)
[ 22.741] (WW) intel(0): i830_uxa_prepare_access: gtt bo map failed: Input/output error
[ 22.742] (EE) intel(0): Failed to submit batch buffer, expect rendering corruption or even a frozen display: Input/output error.
[ 23.491] (WW) intel(0): i830_uxa_prepare_access: gtt bo map failed: Input/output error
[ 25.810] (WW) intel(0): i830_uxa_prepare_access: gtt bo map failed: Input/output error
[ 27.331] (WW) intel(0): i830_uxa_pixmap_swap_bo_with_image: bo map failed
[ 36.690] (WW) intel(0): i830_uxa_prepare_access: gtt bo map failed: Input/output error
[ 92.531] (WW) intel(0): i830_uxa_pixmap_swap_bo_with_image: bo map failed
[-- Attachment #4: xorg.conf --]
[-- Type: text/plain, Size: 2835 bytes --]
Section "ServerLayout"
Identifier "Default Layout"
Screen "TV"
EndSection
Section "Device"
Identifier "Intel HD Graphics"
Driver "intel"
BusID "PCI:0:2:0"
# Using the name of the output defined by the video driver plus the identifier of a
# monitor section, one associates a monitor section with an output by adding an
# option to the Device section in the following format:
# Option "Monitor-outputname" "monitor ID"
Option "monitor-HDMI2" "TSB-TV"
Option "ForceSDVODetect" "on"
#Option "UseEdidFreqs" "FALSE"
#Option "UseEDIDDpi" "FALSE"
#Option "IgnoreEDID" "1"
#Option "ModeValidation" "NoEdidModes"
Option "ConnectedMonitor" "TSB-TV"
Option "CustomEDID" "TSB-TV:/etc/X11/TSB0103.bin"
#Option "ModeDebug" "true"
EndSection
Section "Monitor"
Identifier "TSB-TV"
VendorName "Toshiba"
ModelName "42WLG66"
# This optional entry specifies whether the monitor should be
# turned on at startup. By default, the server will attempt to
# enable all connected monitors.
Option "Enable" "true"
Modeline "1920x1080i" 74.25 1920 2448 2492 2640 1080 1084 1094 1125 interlace +hsync +vsync
Modeline "1920x1080_30.00" 80.18 1920 1984 2176 2432 1080 1081 1084 1099 -HSync +Vsync
Modeline "1920x1080i_30.00" 80.18 1920 1984 2176 2432 1080 1081 1084 1099 -HSync +Vsync interlace
Modeline "1920x1080i_28.00" 73.79 1920 1968 2160 2400 1080 1081 1084 1098 interlace -HSync +Vsync
Modeline "1920x1080_28.00" 73.79 1920 1968 2160 2400 1080 1081 1084 1098 -HSync +Vsync
Modeline "1280x720_50.0" 74.25 1280 1720 1760 1980 720 725 730 750 +hsync +vsync
Option "PreferredMode" "1920x1080i"
HorizSync 15.0 - 46.0
VertRefresh 49.0 - 122.0
#This optional entry specifies that the monitor should be ignored
# entirely, and not reported through RandR. This is useful if the
# hardware reports the presence of outputs that do not exist.
#Option "Ignore" "True"
EndSection
Section "Screen"
Identifier "TV"
Device "Intel HD Graphics"
Monitor "TSB-TV"
DefaultDepth 24
SubSection "Display"
Depth 24 Modes "1920x1080" "1920x1080i" "1920x1080i_30.00" "1920x1080i_28.00" "1920x1080_30.00" "1920x1080_28.00" "1280x720_50.0" "1280x720" "1600x1200"
EndSubSection
EndSection
[-- Attachment #5: Type: text/plain, Size: 159 bytes --]
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
http://lists.freedesktop.org/mailman/listinfo/intel-gfx
^ permalink raw reply [flat|nested] 7+ messages in thread* Re : Does xf86-video-intel 2.11.0 support interlace? Lucid 2.6.33
2010-05-31 19:08 Does xf86-video-intel 2.11.0 support interlace? Lucid 2.6.33 Xavier de Almeida
@ 2010-06-01 9:16 ` Xavier de Almeida
2010-06-03 15:23 ` Marc Deop i Argemí
1 sibling, 0 replies; 7+ messages in thread
From: Xavier de Almeida @ 2010-06-01 9:16 UTC (permalink / raw)
To: intel-gfx
[-- Attachment #1.1: Type: text/plain, Size: 3154 bytes --]
Another question would be to know if i915 is the correct module for the Intel HD Graphics from a Clarkdale i3 proc?
Thanks
XabiX
________________________________
De : Xavier de Almeida <xavierdealmeida@yahoo.fr>
À : intel-gfx@lists.freedesktop.org
Envoyé le : Lun 31 mai 2010, 21h 08min 15s
Objet : [Intel-gfx] Does xf86-video-intel 2.11.0 support interlace? Lucid 2.6.33
Hello,
It's my first post in such mailing list. My issue is that I can't configure my old LCD supporting 1080i (interlace mode) with my Clarkdale i3 (h57) HD Graphics.
I see in the Xorg log such messages:
(II) intel(0): Not using mode "1920x1080i" (interlace mode not supported)
Therefore my 1st question is to know if interlace is supposed to work with these drivers?
Then I'd like to know what I am missing in my xorg.conf in order to be able to set this display mode (and also when the TV is not connected or powered on).
My issue is that the resolution "negotiated" is 1280x720_50.0 instead of 1920x1080i.
Thanks
XabiX
lspci:
00:02.0 VGA compatible controller [0300]: Intel Corporation Core Processor Integrated Graphics Controller [8086:0042] (rev 12)
Subsystem: Giga-byte Technology Device [1458:d000]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 29
Region 0: Memory at fb400000 (64-bit, non-prefetchable) [size=4M]
Region 2: Memory at e0000000 (64-bit, prefetchable) [size=256M]
Region 4: I/O ports at ff00 [size=8]
Capabilities: [90] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+
Address: fee0500c Data: 41a9
Capabilities: [d0] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [a4] PCIe advanced features <?>
Kernel driver in use: i915
Kernel modules: i915
My EDID:
# EDID version 1 revision 3
Section "Monitor"
# Block type: 2:0 3:fc
Identifier "TSB-TV"
VendorName "TSB"
ModelName "TSB-TV"
# Block type: 2:0 3:fc
# Block type: 2:0 3:fd
HorizSync 15-46
VertRefresh 49-61
# Max dot clock (video bandwidth) 80 MHz
# DPMS capabilities: Active off:no Suspend:no Standby:no
Mode "1920x540" # vfreq 50.044Hz, hfreq 28.125kHz
DotClock 74.250000
HTimings 1920 1968 2012 2640
VTimings 540 542 547 562
Flags "Interlace" "+HSync" "+VSync"
EndMode
Mode "1280x720" # vfreq 50.000Hz, hfreq 37.500kHz
DotClock 74.250000
HTimings 1280 1464 1504 1980
VTimings 720 725 730 750
Flags "+HSync" "+VSync"
EndMode
[-- Attachment #1.2: Type: text/html, Size: 4211 bytes --]
[-- Attachment #2: Type: text/plain, Size: 159 bytes --]
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
http://lists.freedesktop.org/mailman/listinfo/intel-gfx
^ permalink raw reply [flat|nested] 7+ messages in thread* Re: Does xf86-video-intel 2.11.0 support interlace? Lucid 2.6.33
2010-05-31 19:08 Does xf86-video-intel 2.11.0 support interlace? Lucid 2.6.33 Xavier de Almeida
2010-06-01 9:16 ` Re : " Xavier de Almeida
@ 2010-06-03 15:23 ` Marc Deop i Argemí
2010-06-03 15:52 ` Marc Deop i Argemí
1 sibling, 1 reply; 7+ messages in thread
From: Marc Deop i Argemí @ 2010-06-03 15:23 UTC (permalink / raw)
To: intel-gfx
On Monday May 31 2010 21:08:15 Xavier de Almeida wrote:
> Hello,
>
> It's my first post in such mailing list. My issue is that I can't configure
> my old LCD supporting 1080i (interlace mode) with my Clarkdale i3 (h57) HD
> Graphics.
>
Is it a known bug?
https://bugs.freedesktop.org/show_bug.cgi?id=27285
--
A: Because it messes up the order in which people normally read text.
Q: Why is top-posting such a bad thing?
A: Top-posting.
Q: What is the most annoying thing in e-mail?
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: Does xf86-video-intel 2.11.0 support interlace? Lucid 2.6.33
2010-06-03 15:23 ` Marc Deop i Argemí
@ 2010-06-03 15:52 ` Marc Deop i Argemí
2010-06-03 16:33 ` Re : " Xavier de Almeida
0 siblings, 1 reply; 7+ messages in thread
From: Marc Deop i Argemí @ 2010-06-03 15:52 UTC (permalink / raw)
To: intel-gfx
On Thursday June 3 2010 17:23:01 Marc Deop i Argemí wrote:
> Is it a known bug?
>
> https://bugs.freedesktop.org/show_bug.cgi?id=27285
Wrong link! Sorry!
https://bugs.freedesktop.org/show_bug.cgi?id=11220
--
A: Because it messes up the order in which people normally read text.
Q: Why is top-posting such a bad thing?
A: Top-posting.
Q: What is the most annoying thing in e-mail?
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re : Does xf86-video-intel 2.11.0 support interlace? Lucid 2.6.33
2010-06-03 15:52 ` Marc Deop i Argemí
@ 2010-06-03 16:33 ` Xavier de Almeida
2010-06-04 15:18 ` Sander Jansen
0 siblings, 1 reply; 7+ messages in thread
From: Xavier de Almeida @ 2010-06-03 16:33 UTC (permalink / raw)
To: intel-gfx
[-- Attachment #1.1: Type: text/plain, Size: 1131 bytes --]
Yes it's the same issue.
Thanks for poiting me to right link.
It looks like no one cares to get this solved as this has been opened since 2007?
at least intel drivers do support this mode on Windows and from the product datasheet nothing was said around no support of interlace under linux
:-(
________________________________
De : Marc Deop i Argemí <damnshock@gmail.com>
À : intel-gfx@lists.freedesktop.org
Envoyé le : Jeu 3 juin 2010, 17h 52min 13s
Objet : Re: [Intel-gfx] Does xf86-video-intel 2.11.0 support interlace? Lucid 2.6.33
On Thursday June 3 2010 17:23:01 Marc Deop i Argemí wrote:
> Is it a known bug?
>
> https://bugs.freedesktop.org/show_bug.cgi?id=27285
Wrong link! Sorry!
https://bugs.freedesktop.org/show_bug.cgi?id=11220
--
A: Because it messes up the order in which people normally read text.
Q: Why is top-posting such a bad thing?
A: Top-posting.
Q: What is the most annoying thing in e-mail?
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
http://lists.freedesktop.org/mailman/listinfo/intel-gfx
[-- Attachment #1.2: Type: text/html, Size: 2169 bytes --]
[-- Attachment #2: Type: text/plain, Size: 159 bytes --]
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
http://lists.freedesktop.org/mailman/listinfo/intel-gfx
^ permalink raw reply [flat|nested] 7+ messages in thread* Re: Re : Does xf86-video-intel 2.11.0 support interlace? Lucid 2.6.33
2010-06-03 16:33 ` Re : " Xavier de Almeida
@ 2010-06-04 15:18 ` Sander Jansen
2010-06-04 15:50 ` Re : " Xavier de Almeida
0 siblings, 1 reply; 7+ messages in thread
From: Sander Jansen @ 2010-06-04 15:18 UTC (permalink / raw)
To: intel-gfx
On Thu, Jun 3, 2010 at 11:33 AM, Xavier de Almeida
<xavierdealmeida@yahoo.fr> wrote:
> Yes it's the same issue.
> Thanks for poiting me to right link.
>
> It looks like no one cares to get this solved as this has been opened since
> 2007?
> at least intel drivers do support this mode on Windows and from the product
> datasheet nothing was said around no support of interlace under linux
> :-(
A feature matrix of the driver would be handy in that respect, to see
what's supported and what's not (compared to the windows driver).
Cheers,
Sander
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re : Re : Does xf86-video-intel 2.11.0 support interlace? Lucid 2.6.33
2010-06-04 15:18 ` Sander Jansen
@ 2010-06-04 15:50 ` Xavier de Almeida
0 siblings, 0 replies; 7+ messages in thread
From: Xavier de Almeida @ 2010-06-04 15:50 UTC (permalink / raw)
To: intel-gfx
[-- Attachment #1.1: Type: text/plain, Size: 1535 bytes --]
I agree with you.
According to the bug raised on this in 2007https://bugs.freedesktop.org/process_bug.cgi
it looks like we should have interlace mode available with the latest intel-drm.
Another similar question is does Intel drivers support DTS-HD/True-HD or at least 5.1 through the HDMI?
i have an external video amplicator so I want him to decode the sound and I want to pass everything transparent through HDMI to the ampli.
Hopefully we get the interlace mode working and available on the basics distribs.
Cheers
XabiX
________________________________
De : Sander Jansen <s.jansen@gmail.com>
À : intel-gfx@lists.freedesktop.org
Envoyé le : Ven 4 juin 2010, 17h 18min 03s
Objet : Re: [Intel-gfx] Re : Does xf86-video-intel 2.11.0 support interlace? Lucid 2.6.33
On Thu, Jun 3, 2010 at 11:33 AM, Xavier de Almeida
<xavierdealmeida@yahoo.fr> wrote:
> Yes it's the same issue.
> Thanks for poiting me to right link.
>
> It looks like no one cares to get this solved as this has been opened since
> 2007?
> at least intel drivers do support this mode on Windows and from the product
> datasheet nothing was said around no support of interlace under linux
> :-(
A feature matrix of the driver would be handy in that respect, to see
what's supported and what's not (compared to the windows driver).
Cheers,
Sander
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
http://lists.freedesktop.org/mailman/listinfo/intel-gfx
[-- Attachment #1.2: Type: text/html, Size: 2725 bytes --]
[-- Attachment #2: Type: text/plain, Size: 159 bytes --]
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
http://lists.freedesktop.org/mailman/listinfo/intel-gfx
^ permalink raw reply [flat|nested] 7+ messages in thread
end of thread, other threads:[~2010-06-04 15:50 UTC | newest]
Thread overview: 7+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2010-05-31 19:08 Does xf86-video-intel 2.11.0 support interlace? Lucid 2.6.33 Xavier de Almeida
2010-06-01 9:16 ` Re : " Xavier de Almeida
2010-06-03 15:23 ` Marc Deop i Argemí
2010-06-03 15:52 ` Marc Deop i Argemí
2010-06-03 16:33 ` Re : " Xavier de Almeida
2010-06-04 15:18 ` Sander Jansen
2010-06-04 15:50 ` Re : " Xavier de Almeida
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.