From: Chris Ball <cjb@laptop.org>
To: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: linux-arm-kernel@lists.infradead.org,
linux-samsung-soc@vger.kernel.org, linux-mmc@vger.kernel.org,
kyungmin.park@samsung.com, ben-linux@fluff.org,
kgene.kim@samsung.com
Subject: Re: [PATCH 4/5] sdhci-s3c: add support for the non standard minimal clock value
Date: Fri, 27 Aug 2010 20:54:52 +0100 [thread overview]
Message-ID: <20100827195452.GM23079@void.printf.net> (raw)
In-Reply-To: <1276076383-24825-5-git-send-email-m.szyprowski@samsung.com>
Hi,
Looks like this wasn't merged. Any thoughts on doing so?
On Wed, Jun 09, 2010 at 11:39:42AM +0200, Marek Szyprowski wrote:
> S3C SDHCI host controller can change the source for generating mmc clock.
> By default host bus clock is used, what causes some problems on machines
> with 133MHz bus, because the SDHCI divider cannot be as high get proper
> clock value for identification mode. This is not a problem for the
> controller, because it can generate lower frequencies from other clock
> sources. This patch adds a new quirk to SDHCI driver to calculate the
> minimal supported clock frequency.
>
> This fixes the flood of the following warnings on Samsung S5PV210 SoCs:
> mmc0: Minimum clock frequency too high for identification mode
>
> Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
> ---
> drivers/mmc/host/sdhci-of-esdhc.c | 1 +
> drivers/mmc/host/sdhci-s3c.c | 29 +++++++++++++++++++++++++++++
> drivers/mmc/host/sdhci.c | 2 +-
> drivers/mmc/host/sdhci.h | 2 ++
> 4 files changed, 33 insertions(+), 1 deletions(-)
>
> diff --git a/drivers/mmc/host/sdhci-of-esdhc.c b/drivers/mmc/host/sdhci-of-esdhc.c
> index c8623de..64b3f79 100644
> --- a/drivers/mmc/host/sdhci-of-esdhc.c
> +++ b/drivers/mmc/host/sdhci-of-esdhc.c
> @@ -124,6 +124,7 @@ struct sdhci_of_data sdhci_esdhc = {
> SDHCI_QUIRK_BROKEN_CARD_DETECTION |
> SDHCI_QUIRK_NO_BUSY_IRQ |
> SDHCI_QUIRK_NONSTANDARD_CLOCK |
> + SDHCI_QUIRK_NONSTANDARD_MINCLOCK |
> SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK |
> SDHCI_QUIRK_PIO_NEEDS_DELAY |
> SDHCI_QUIRK_RESTORE_IRQS_AFTER_RESET |
> diff --git a/drivers/mmc/host/sdhci-s3c.c b/drivers/mmc/host/sdhci-s3c.c
> index 2b6cb44..615008d 100644
> --- a/drivers/mmc/host/sdhci-s3c.c
> +++ b/drivers/mmc/host/sdhci-s3c.c
> @@ -209,10 +209,37 @@ static void sdhci_s3c_set_clock(struct sdhci_host *host, unsigned int clock)
> }
> }
>
> +/**
> + * sdhci_s3c_get_min_clock - callback to get minimal supported clock value
> + * @host: The SDHCI host being queried
> + *
> + * To init mmc host properly a minimal clock value is needed. For high system
> + * bus clock's values the standard formula gives values out of allowed range.
> + * The clock still can be set to lower values, if clock source other then
> + * system bus is selected.
> +*/
> +static unsigned int sdhci_s3c_get_min_clock(struct sdhci_host *host)
> +{
> + struct sdhci_s3c *ourhost = to_s3c(host);
> + unsigned int delta, min = UINT_MAX;
> + int src;
> +
> + for (src = 0; src < MAX_BUS_CLK; src++) {
> + delta = sdhci_s3c_consider_clock(ourhost, src, 0);
> + if (delta == UINT_MAX)
> + continue;
> + /* delta is a negative value in this case */
> + if (-delta < min)
> + min = -delta;
> + }
> + return min;
> +}
> +
> static struct sdhci_ops sdhci_s3c_ops = {
> .get_max_clock = sdhci_s3c_get_max_clk,
> .get_timeout_clock = sdhci_s3c_get_timeout_clk,
> .set_clock = sdhci_s3c_set_clock,
> + .get_min_clock = sdhci_s3c_get_min_clock,
> };
>
> static int __devinit sdhci_s3c_probe(struct platform_device *pdev)
> @@ -316,6 +343,8 @@ static int __devinit sdhci_s3c_probe(struct platform_device *pdev)
> host->quirks = 0;
> host->irq = irq;
>
> + host->quirks |= SDHCI_QUIRK_NONSTANDARD_MINCLOCK;
> +
> /* Setup quirks for the controller */
> host->quirks |= SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC;
>
> diff --git a/drivers/mmc/host/sdhci.c b/drivers/mmc/host/sdhci.c
> index c6d1bd8..8b3ee53 100644
> --- a/drivers/mmc/host/sdhci.c
> +++ b/drivers/mmc/host/sdhci.c
> @@ -1785,7 +1785,7 @@ int sdhci_add_host(struct sdhci_host *host)
> * Set host parameters.
> */
> mmc->ops = &sdhci_ops;
> - if (host->quirks & SDHCI_QUIRK_NONSTANDARD_CLOCK &&
> + if (host->quirks & SDHCI_QUIRK_NONSTANDARD_MINCLOCK &&
> host->ops->set_clock && host->ops->get_min_clock)
> mmc->f_min = host->ops->get_min_clock(host);
> else
> diff --git a/drivers/mmc/host/sdhci.h b/drivers/mmc/host/sdhci.h
> index c846813..3fd87c2 100644
> --- a/drivers/mmc/host/sdhci.h
> +++ b/drivers/mmc/host/sdhci.h
> @@ -240,6 +240,8 @@ struct sdhci_host {
> #define SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN (1<<25)
> /* Controller cannot support End Attribute in NOP ADMA descriptor */
> #define SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC (1<<26)
> +/* Controller has nonstandard clock management */
> +#define SDHCI_QUIRK_NONSTANDARD_MINCLOCK (1<<27)
>
> int irq; /* Device IRQ */
> void __iomem * ioaddr; /* Mapped address */
> --
> 1.7.1.240.g225c
--
Chris Ball <cjb@laptop.org> <http://printf.net/>
One Laptop Per Child
WARNING: multiple messages have this Message-ID (diff)
From: cjb@laptop.org (Chris Ball)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH 4/5] sdhci-s3c: add support for the non standard minimal clock value
Date: Fri, 27 Aug 2010 20:54:52 +0100 [thread overview]
Message-ID: <20100827195452.GM23079@void.printf.net> (raw)
In-Reply-To: <1276076383-24825-5-git-send-email-m.szyprowski@samsung.com>
Hi,
Looks like this wasn't merged. Any thoughts on doing so?
On Wed, Jun 09, 2010 at 11:39:42AM +0200, Marek Szyprowski wrote:
> S3C SDHCI host controller can change the source for generating mmc clock.
> By default host bus clock is used, what causes some problems on machines
> with 133MHz bus, because the SDHCI divider cannot be as high get proper
> clock value for identification mode. This is not a problem for the
> controller, because it can generate lower frequencies from other clock
> sources. This patch adds a new quirk to SDHCI driver to calculate the
> minimal supported clock frequency.
>
> This fixes the flood of the following warnings on Samsung S5PV210 SoCs:
> mmc0: Minimum clock frequency too high for identification mode
>
> Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
> ---
> drivers/mmc/host/sdhci-of-esdhc.c | 1 +
> drivers/mmc/host/sdhci-s3c.c | 29 +++++++++++++++++++++++++++++
> drivers/mmc/host/sdhci.c | 2 +-
> drivers/mmc/host/sdhci.h | 2 ++
> 4 files changed, 33 insertions(+), 1 deletions(-)
>
> diff --git a/drivers/mmc/host/sdhci-of-esdhc.c b/drivers/mmc/host/sdhci-of-esdhc.c
> index c8623de..64b3f79 100644
> --- a/drivers/mmc/host/sdhci-of-esdhc.c
> +++ b/drivers/mmc/host/sdhci-of-esdhc.c
> @@ -124,6 +124,7 @@ struct sdhci_of_data sdhci_esdhc = {
> SDHCI_QUIRK_BROKEN_CARD_DETECTION |
> SDHCI_QUIRK_NO_BUSY_IRQ |
> SDHCI_QUIRK_NONSTANDARD_CLOCK |
> + SDHCI_QUIRK_NONSTANDARD_MINCLOCK |
> SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK |
> SDHCI_QUIRK_PIO_NEEDS_DELAY |
> SDHCI_QUIRK_RESTORE_IRQS_AFTER_RESET |
> diff --git a/drivers/mmc/host/sdhci-s3c.c b/drivers/mmc/host/sdhci-s3c.c
> index 2b6cb44..615008d 100644
> --- a/drivers/mmc/host/sdhci-s3c.c
> +++ b/drivers/mmc/host/sdhci-s3c.c
> @@ -209,10 +209,37 @@ static void sdhci_s3c_set_clock(struct sdhci_host *host, unsigned int clock)
> }
> }
>
> +/**
> + * sdhci_s3c_get_min_clock - callback to get minimal supported clock value
> + * @host: The SDHCI host being queried
> + *
> + * To init mmc host properly a minimal clock value is needed. For high system
> + * bus clock's values the standard formula gives values out of allowed range.
> + * The clock still can be set to lower values, if clock source other then
> + * system bus is selected.
> +*/
> +static unsigned int sdhci_s3c_get_min_clock(struct sdhci_host *host)
> +{
> + struct sdhci_s3c *ourhost = to_s3c(host);
> + unsigned int delta, min = UINT_MAX;
> + int src;
> +
> + for (src = 0; src < MAX_BUS_CLK; src++) {
> + delta = sdhci_s3c_consider_clock(ourhost, src, 0);
> + if (delta == UINT_MAX)
> + continue;
> + /* delta is a negative value in this case */
> + if (-delta < min)
> + min = -delta;
> + }
> + return min;
> +}
> +
> static struct sdhci_ops sdhci_s3c_ops = {
> .get_max_clock = sdhci_s3c_get_max_clk,
> .get_timeout_clock = sdhci_s3c_get_timeout_clk,
> .set_clock = sdhci_s3c_set_clock,
> + .get_min_clock = sdhci_s3c_get_min_clock,
> };
>
> static int __devinit sdhci_s3c_probe(struct platform_device *pdev)
> @@ -316,6 +343,8 @@ static int __devinit sdhci_s3c_probe(struct platform_device *pdev)
> host->quirks = 0;
> host->irq = irq;
>
> + host->quirks |= SDHCI_QUIRK_NONSTANDARD_MINCLOCK;
> +
> /* Setup quirks for the controller */
> host->quirks |= SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC;
>
> diff --git a/drivers/mmc/host/sdhci.c b/drivers/mmc/host/sdhci.c
> index c6d1bd8..8b3ee53 100644
> --- a/drivers/mmc/host/sdhci.c
> +++ b/drivers/mmc/host/sdhci.c
> @@ -1785,7 +1785,7 @@ int sdhci_add_host(struct sdhci_host *host)
> * Set host parameters.
> */
> mmc->ops = &sdhci_ops;
> - if (host->quirks & SDHCI_QUIRK_NONSTANDARD_CLOCK &&
> + if (host->quirks & SDHCI_QUIRK_NONSTANDARD_MINCLOCK &&
> host->ops->set_clock && host->ops->get_min_clock)
> mmc->f_min = host->ops->get_min_clock(host);
> else
> diff --git a/drivers/mmc/host/sdhci.h b/drivers/mmc/host/sdhci.h
> index c846813..3fd87c2 100644
> --- a/drivers/mmc/host/sdhci.h
> +++ b/drivers/mmc/host/sdhci.h
> @@ -240,6 +240,8 @@ struct sdhci_host {
> #define SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN (1<<25)
> /* Controller cannot support End Attribute in NOP ADMA descriptor */
> #define SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC (1<<26)
> +/* Controller has nonstandard clock management */
> +#define SDHCI_QUIRK_NONSTANDARD_MINCLOCK (1<<27)
>
> int irq; /* Device IRQ */
> void __iomem * ioaddr; /* Mapped address */
> --
> 1.7.1.240.g225c
--
Chris Ball <cjb@laptop.org> <http://printf.net/>
One Laptop Per Child
next prev parent reply other threads:[~2010-08-27 19:54 UTC|newest]
Thread overview: 31+ messages / expand[flat|nested] mbox.gz Atom feed top
2010-06-09 9:39 [PATCH] SDHCI-S3C fixes and enhancements (driver specific code) Marek Szyprowski
2010-06-09 9:39 ` Marek Szyprowski
2010-06-09 9:39 ` [PATCH 1/5] sdhci-s3c: depend on plat-samsung Marek Szyprowski
2010-06-09 9:39 ` Marek Szyprowski
2010-06-11 0:29 ` Kukjin Kim
2010-06-11 0:29 ` Kukjin Kim
2010-06-11 5:24 ` Ben Dooks
2010-06-11 5:24 ` Ben Dooks
2010-06-11 5:42 ` Kyungmin Park
2010-06-11 5:42 ` Kyungmin Park
2010-06-11 10:30 ` Mark Brown
2010-06-11 10:30 ` Mark Brown
2010-06-09 9:39 ` [PATCH 2/5] sdhci-s3c: add missing remove function Marek Szyprowski
2010-06-09 9:39 ` Marek Szyprowski
2010-06-09 9:39 ` [PATCH 3/5] sdhci-s3c: increase the timeout value Marek Szyprowski
2010-06-09 9:39 ` Marek Szyprowski
2010-06-10 10:46 ` Kukjin Kim
2010-06-10 10:46 ` Kukjin Kim
2010-08-27 19:53 ` Chris Ball
2010-08-27 19:53 ` Chris Ball
2010-06-09 9:39 ` [PATCH 4/5] sdhci-s3c: add support for the non standard minimal clock value Marek Szyprowski
2010-06-09 9:39 ` Marek Szyprowski
2010-08-27 19:54 ` Chris Ball [this message]
2010-08-27 19:54 ` Chris Ball
2010-08-28 0:54 ` Kukjin Kim
2010-08-28 0:54 ` Kukjin Kim
2010-08-28 2:29 ` Chris Ball
2010-06-09 9:39 ` [PATCH 5/5] sdhci-s3c: add support for new card detection methods Marek Szyprowski
2010-06-09 9:39 ` Marek Szyprowski
2010-06-10 12:06 ` [PATCH 5/5 fixed] " Marek Szyprowski
2010-06-10 12:06 ` Marek Szyprowski
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20100827195452.GM23079@void.printf.net \
--to=cjb@laptop.org \
--cc=ben-linux@fluff.org \
--cc=kgene.kim@samsung.com \
--cc=kyungmin.park@samsung.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-mmc@vger.kernel.org \
--cc=linux-samsung-soc@vger.kernel.org \
--cc=m.szyprowski@samsung.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.