From: Christian Lamparter <chunkeey@googlemail.com>
To: "linux-wireless" <linux-wireless@vger.kernel.org>
Cc: "John W. Linville" <linville@tuxdriver.com>,
Johannes Berg <johannes@sipsolutions.net>,
Ben Greear <greearb@candelatech.com>,
rainbow lum <rainbowlum@gmail.com>
Subject: phyX enumeration conflict
Date: Fri, 8 Oct 2010 21:59:58 +0200 [thread overview]
Message-ID: <201010082159.59262.chunkeey@googlemail.com> (raw)
This is a report from a user(added to CC):
He has two different mac80211-powered USB devices:
one which has an ISL3887 (supported by p54usb),
the other is an AR9170 (carl9170).
"I found another problem---the driver use the phy index from 0, which
will conflict with p54usb driver(i have two wifi card,another one use
p54usb). this will cause boot-period wireless init fail.
bellow are some details.
[ 5.049234] usbcore: registered new interface driver usbfs
[ 5.069937] usbcore: registered new interface driver hub
[ 5.093766] usbcore: registered new device driver usb
[ 5.163736] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 5.170118] ohci_hcd 0000:00:0a.0: OHCI Host Controller
[ 5.190581] ohci_hcd 0000:00:0a.0: new USB bus registered, assigned bus
number 1
[ 5.202619] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 5.233765] ohci_hcd 0000:00:0a.0: irq 7, io mem 0xfeffd000
[ 5.248441] Warning! ehci_hcd should always be loaded before uhci_hcd and
ohci_hcd, not after
[ 5.328444] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
[ 5.335301] usb usb1: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 5.342550] usb usb1: Product: OHCI Host Controller
[ 5.349599] usb usb1: Manufacturer: Linux 2.6.36-rc6-wl-wlplug20101006
ohci_hcd
[ 5.362825] usb usb1: SerialNumber: 0000:00:0a.0
[ 5.369904] hub 1-0:1.0: USB hub found
[ 5.373812] hub 1-0:1.0: 2 ports detected
[ 5.379112] ehci_hcd 0000:00:0a.1: EHCI Host Controller
[ 5.384472] ehci_hcd 0000:00:0a.1: new USB bus registered, assigned bus
number 2
[ 5.415841] ehci_hcd 0000:00:0a.1: irq 9, io mem 0xfefff800
[ 5.433679] ehci_hcd 0000:00:0a.1: USB 2.0 started, EHCI 1.00
[ 5.439605] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 5.446451] usb usb2: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 5.453717] usb usb2: Product: EHCI Host Controller
[ 5.458621] usb usb2: Manufacturer: Linux 2.6.36-rc6-wl-wlplug20101006
ehci_hcd
[ 5.465974] usb usb2: SerialNumber: 0000:00:0a.1
[ 5.472880] hub 2-0:1.0: USB hub found
[ 5.476790] hub 2-0:1.0: 2 ports detected
[ 5.482134] ohci_hcd 0000:00:0b.0: OHCI Host Controller
[ 5.487507] ohci_hcd 0000:00:0b.0: new USB bus registered, assigned bus
number 3
[ 5.495105] ohci_hcd 0000:00:0b.0: irq 10, io mem 0xfeffe000
[ 5.583815] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 5.590635] usb usb3: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 5.597906] usb usb3: Product: OHCI Host Controller
[ 5.602810] usb usb3: Manufacturer: Linux 2.6.36-rc6-wl-wlplug20101006
ohci_hcd
[ 5.610216] usb usb3: SerialNumber: 0000:00:0b.0
[ 5.617114] hub 3-0:1.0: USB hub found
[ 5.620920] hub 3-0:1.0: 2 ports detected
[ 5.626326] ehci_hcd 0000:00:0b.1: EHCI Host Controller
[ 5.631628] ehci_hcd 0000:00:0b.1: new USB bus registered, assigned bus
number 4
[ 5.723840] ehci_hcd 0000:00:0b.1: irq 11, io mem 0xfefffc00
[ 5.793740] usb 2-2: new high speed USB device using ehci_hcd and address
2
[ 5.813661] ehci_hcd 0000:00:0b.1: USB 2.0 started, EHCI 1.00
[ 5.819624] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002
[ 5.826550] usb usb4: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 5.833845] usb usb4: Product: EHCI Host Controller
[ 5.838765] usb usb4: Manufacturer: Linux 2.6.36-rc6-wl-wlplug20101006
ehci_hcd
[ 5.846122] usb usb4: SerialNumber: 0000:00:0b.1
[ 5.853073] hub 4-0:1.0: USB hub found
[ 5.856972] hub 4-0:1.0: 2 ports detected
[ 6.012773] usb 2-2: New USB device found, idVendor=0cf3, idProduct=1002
[ 6.019545] usb 2-2: New USB device strings: Mfr=16, Product=32,
SerialNumber=48
[ 6.026993] usb 2-2: Product: USB2.0 WLAN
[ 6.031041] usb 2-2: Manufacturer: ATHER
[ 6.037793] usb 2-2: SerialNumber: 12345
[ 6.264804] REISERFS (device hda1): found reiserfs format "3.6" with
standard journal
[ 6.272704] REISERFS (device hda1): using ordered data mode
[ 6.285441] REISERFS (device hda1): journal params: device hda1, size
8192, journal first block 18, max trans len 1024, max batch 900, max commit
age 30, max trans age 30
[ 6.311500] REISERFS (device hda1): checking transaction log (hda1)
[ 6.343736] usb 4-2: new high speed USB device using ehci_hcd and address
2
[ 6.498133] usb 4-2: New USB device found, idVendor=1435, idProduct=0427
[ 6.505010] usb 4-2: New USB device strings: Mfr=1, Product=2,
SerialNumber=0
[ 6.512273] usb 4-2: Product: Cohiba 3887 rev0
[ 6.516876] usb 4-2: Manufacturer: GlobespanVirata
[ 6.604230] REISERFS (device hda1): replayed 22 transactions in 0 seconds
[ 6.611613] REISERFS (device hda1): Using r5 hash to sort names
[ 14.180410] udevd version 125 started
[ 17.303283] rtc_cmos rtc_cmos: rtc core: registered rtc_cmos as rtc0
[ 17.394543] rtc0: alarms up to one day, 114 bytes nvram
[ 18.090664] cfg80211: Calling CRDA to update world regulatory domain
[ 18.944222] usb 2-2: reset high speed USB device using ehci_hcd and
address 2
[ 19.141331] usbcore: registered new interface driver carl9170
[ 19.244279] usb 4-2: reset high speed USB device using ehci_hcd and
address 2
[ 19.286717] usb 2-2: driver API: 1.8.8.3 2010-09-28 [1-1]
[ 19.292335] usb 2-2: firmware API: 1.8.8.3 2010-09-28
[ 19.482896] ieee80211 phy0: p54 detected a LM87 firmware ----------phy0
used by p54usb
[ 19.492278] p54: rx_mtu reduced from 3240 to 2384
[ 19.500711] ieee80211 phy0: FW rev 2.13.24.0 - Softmac protocol 5.9
[ 19.507146] ieee80211 phy0: cryptographic accelerator WEP:YES, TKIP:YES,
CCMP:YES
[ 20.511550] ieee80211 phy0: hwaddr 00:0b:6b:9d:9e:12, MAC:isl3887
RF:Frisbee
[ 20.596019] ath: EEPROM regdomain: 0x809c
[ 20.596047] ath: EEPROM indicates we should expect a country code
[ 20.596070] ath: doing EEPROM country->regdmn map search
[ 20.596091] ath: country maps to regdmn code: 0x52
[ 20.596112] ath: Country alpha2 being used: CN
[ 20.596130] ath: Regpair used: 0x52
[ 20.596317] ------------[ cut here ]------------
[ 20.600994] WARNING: at fs/sysfs/dir.c:451 sysfs_add_one+0x82/0xa0()
[ 20.624263] sysfs: cannot create duplicate filename
'/class/ieee80211/phy0' --seems carl9170 want to use the same phy id which
was taken by p54usb
[ 20.631249] Modules linked in: p54usb(+) carl9170 p54common led_class
crc_ccitt mac80211 ath cfg80211 rtc_cmos ehci_hcd ohci_hcd usbcore
ide_gd_mod
[ 20.664483] Pid: 1141, comm: firmware/carl91 Not tainted
2.6.36-rc6-wl-wlplug20101006 #1
[ 20.672595] Call Trace:
[ 20.684320] [<c10d0d52>] ? sysfs_add_one+0x82/0xa0
[ 20.689235] [<c10d0d52>] ? sysfs_add_one+0x82/0xa0
[ 20.694159] [<c101e37c>] warn_slowpath_common+0x6c/0xa0
[ 20.714291] [<c10d0d52>] ? sysfs_add_one+0x82/0xa0
[ 20.719210] [<c101e42e>] warn_slowpath_fmt+0x2e/0x30
[ 20.734351] [<c10d0d52>] sysfs_add_one+0x82/0xa0
[ 20.739098] [<c10d1c71>] sysfs_do_create_link+0xf1/0x1d0
[ 20.754405] [<c10d0565>] ? sysfs_add_file_mode+0x55/0x90
[ 20.759855] [<c10d1d82>] sysfs_create_link+0x12/0x20
[ 20.774302] [<c1190d74>] device_add+0x124/0x580
[ 20.779007] [<e099091b>] wiphy_register+0x19b/0x280 [cfg80211]
[ 20.794752] [<c1083cb0>] ? __kmalloc+0x70/0xc0
[ 20.799374] [<e0a5442e>] ieee80211_register_hw+0x17e/0x530 [mac80211]
[ 20.824361] [<e0b265f0>] ? carl9170_reg_notifier+0x0/0x40 [carl9170]
[ 20.830849] [<e0b2639e>] carl9170_register+0x1ee/0x440 [carl9170]
[ 20.844310] [<c1197920>] ? request_firmware_work_func+0x0/0x80
[ 20.850280] [<e0b29ed1>] carl9170_usb_firmware_step2+0x81/0xe0
[carl9170]
[ 20.874296] [<c1197920>] ? request_firmware_work_func+0x0/0x80
[ 20.880253] [<c119795b>] request_firmware_work_func+0x3b/0x80
[ 20.894782] [<c1035c24>] kthread+0x74/0x80
[ 20.899003] [<c1035bb0>] ? kthread+0x0/0x80
[ 20.903307] [<c1002fb6>] kernel_thread_helper+0x6/0x10
[ 20.924282] ---[ end trace 9fa154a9ec88252b ]---
[ 21.238237] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 21.240677] Registered led device: p54-phy0::assoc
[ 21.240874] Registered led device: p54-phy0::tx
[ 21.241065] Registered led device: p54-phy0::rx
[ 21.241259] Registered led device: p54-phy0::radio
[ 21.241331] usb 4-2: is registered as 'phy0'
[ 21.251183] usbcore: registered new interface driver p54usb
[ 21.287635] udev: renamed network interface wlan0 to wlan2
[ 23.197295] Adding 1004024k swap on /dev/hda5. Priority:-1 extents:1
across:1004024k
and when I replug the usb device it shows:
[ 381.379902] usb 2-2: USB disconnect, address 2
[ 384.589713] usb 2-2: new high speed USB device using ehci_hcd and address
3
[ 384.797802] usb 2-2: New USB device found, idVendor=0cf3, idProduct=1002
[ 384.805225] usb 2-2: New USB device strings: Mfr=16, Product=32,
SerialNumber=48
[ 384.813306] usb 2-2: Product: USB2.0 WLAN
[ 384.817350] usb 2-2: Manufacturer: ATHER
[ 384.822311] usb 2-2: SerialNumber: 12345
[ 385.229748] usb 2-2: reset high speed USB device using ehci_hcd and
address 3
[ 385.428787] usbcore: registered new interface driver carl9170
[ 385.501003] usb 2-2: driver API: 1.8.8.3 2010-09-28 [1-1]
[ 385.506622] usb 2-2: firmware API: 1.8.8.3 2010-09-28
[ 386.805068] ath: EEPROM regdomain: 0x809c
[ 386.805095] ath: EEPROM indicates we should expect a country code
[ 386.805119] ath: doing EEPROM country->regdmn map search
[ 386.805139] ath: country maps to regdmn code: 0x52
[ 386.805161] ath: Country alpha2 being used: CN
[ 386.805178] ath: Regpair used: 0x52
[ 386.812918] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
[ 386.816154] cfg80211: Calling CRDA for country: CN
[ 386.833303] input: phy1 WPS Button as
/devices/pci0000:00/0000:00:0a.1/usb2/2-2/2-2:1.0/ieee80211/phy1/input0
[ 386.846922] udev: renamed network interface wlan0 to wlan6
[ 386.879907] usb 2-2: Atheros AR9170 is registered as 'phy1' --------
then all goes fine."
In a roundup he said that the bug might originate from:
http://git.kernel.org/?p=linux/kernel/git/linville/wireless-testing.git;a=commitdiff;h=5a254ffe3ffdfa84fe076009bd8e88da412180d2
and that a previous version of net/wireless/core.c
solved the problem.
next reply other threads:[~2010-10-08 20:00 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
2010-10-08 19:59 Christian Lamparter [this message]
2010-10-10 8:09 ` phyX enumeration conflict Johannes Berg
2010-10-10 8:16 ` Johannes Berg
2010-10-10 15:39 ` Ben Greear
2010-10-10 16:43 ` Johannes Berg
2010-10-11 17:26 ` Ben Greear
2010-10-11 17:34 ` Johannes Berg
2010-10-11 17:46 ` Ben Greear
2010-10-11 17:56 ` Johannes Berg
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=201010082159.59262.chunkeey@googlemail.com \
--to=chunkeey@googlemail.com \
--cc=greearb@candelatech.com \
--cc=johannes@sipsolutions.net \
--cc=linux-wireless@vger.kernel.org \
--cc=linville@tuxdriver.com \
--cc=rainbowlum@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.