Re: [lm-sensors] weird lectures

[Guenter Roeck <guenter.roeck@ericsson.com>]

On Fri, Dec 10, 2010 at 09:32:47AM -0500, Jose M. Caballero wrote:
> El jue, 09-12-2010 a las 08:20 -0800, Guenter Roeck escribió:
> > On Thu, Dec 09, 2010 at 11:09:34AM -0500, José M. Caballero wrote:
> > [ ... ]
> > > 
> > > Thanks a lot. Finally it works.
> > > But it is very worrying lectures:
> > > 
> > > 
> > > w83667hg-isa-0290
> > > Adapter: ISA adapter
> > > in0:         +0.89 V  (min =  +0.00 V, max =  +1.74 V)   
> > > in1:         +1.86 V  (min =  +0.73 V, max =  +1.97 V)   
> > > in2:         +3.42 V  (min =  +0.45 V, max =  +3.82 V)   
> > > in3:         +3.42 V  (min =  +1.18 V, max =  +0.27 V)   ALARM
> > > in4:         +0.05 V  (min =  +0.50 V, max =  +0.11 V)   ALARM
> > > in5:         +1.74 V  (min =  +1.39 V, max =  +0.91 V)   ALARM
> > > in7:         +3.44 V  (min =  +0.90 V, max =  +3.07 V)   ALARM
> > > in8:         +3.30 V  (min =  +1.31 V, max =  +1.76 V)   ALARM
> > > fan1:          0 RPM  (min =  340 RPM, div = 128)  ALARM
> > > fan2:       2008 RPM  (min =  448 RPM, div = 32)
> > > fan3:          0 RPM  (min =  405 RPM, div = 128)  ALARM
> > > temp1:       +30.0°C  (high = -10.0°C, hyst =  -5.0°C)  ALARM  sensor > > > thermistor
> > > temp2:       +32.0°C  (high = +80.0°C, hyst = +75.0°C)  sensor > > > thermistor
> > > temp3:      +127.5°C  (high = +80.0°C, hyst = +75.0°C)  ALARM  sensor > > > thermistor
> > > cpu0_vid:   +2.500 V
> > > 
> > > I hope the sensor doesn't work properly...
> > > 
> > temp3 is probably not connected, as is fan1 and fan3. The temp1 high limit seems to be 
> > unset. The voltage limits look odd, with max being lower than min in some cases.
> > Since ALARM is set for those voltages, I suspect that the limits are not set correctly.
> > You can test that by setting more reasonable limits for one of the voltages (and temp1)
> > and verify if that resets the ALARM bit.
> > 
> > Guenter
> > 
> 
> After installing (successfully) lm-sensors and the standalone patch for
> Nuvoton w83627hg-b (w83627ehf driver), I have not a /etc/sensors.conf
> file just a sensors3.conf file with next relevant data:
>  
> chip "w83627ehf-*" "w83627dhg-*"
>  
>     label in0 "Vcore"
>     label in2 "AVCC"
>     label in3 "VCC"
>     label in7 "3VSB"
>     label in8 "Vbat"
>  
>     set in2_min  3.3 * 0.90
>     set in2_max  3.3 * 1.10
>     set in3_min  3.3 * 0.90
>     set in3_max  3.3 * 1.10
>     set in7_min  3.3 * 0.90
>     set in7_max  3.3 * 1.10
>     set in8_min  3.0 * 0.90
>     set in8_max  3.0 * 1.10
>     
> (The same data as the sensors.conf.default from the
> lm_sensors-3.2.0.tar.bz2)
>  
> Could be due to that some of my amazing readings of 'sensors'? How to
> fix it?
> 
Might well be. I would suggest to remove the set lines (or comment them out) and 
restart your system.

Guenter

_______________________________________________
lm-sensors mailing list
lm-sensors@lm-sensors.org
http://lists.lm-sensors.org/mailman/listinfo/lm-sensors