[PATCH v2 1/2] PRUSS UIO driver support

[hjk@hansjkoch.de (Hans J. Koch)]

On Mon, Feb 21, 2011 at 11:05:14PM +0530, Pratheesh Gangadhar wrote:
> This patch implements PRUSS (Programmable Real-time Unit Sub System)
> UIO driver which exports SOC resources associated with PRUSS like
> I/O, memories and IRQs to user space. PRUSS is dual 32-bit RISC
> processors which is efficient in performing embedded tasks that
> require manipulation of packed memory mapped data structures and
> efficient in handling system events that have tight real time
> constraints. This driver is currently supported on Texas Instruments
> DA850, AM18xx and OMAPL1-38 devices.
> For example, PRUSS runs firmware for real-time critical industrial
> communication data link layer and communicates with application stack
> running in user space via shared memory and IRQs.
> 
> Signed-off-by: Pratheesh Gangadhar <pratheesh@ti.com>

Looks much better now. Just some minor issues, see below.

Thanks,
Hans

> ---
>  drivers/uio/Kconfig     |    9 ++
>  drivers/uio/Makefile    |    1 +
>  drivers/uio/uio_pruss.c |  231 +++++++++++++++++++++++++++++++++++++++++++++++
>  3 files changed, 241 insertions(+), 0 deletions(-)
>  create mode 100644 drivers/uio/uio_pruss.c
> 
> diff --git a/drivers/uio/Kconfig b/drivers/uio/Kconfig
> index bb44079..f92f20d 100644
> --- a/drivers/uio/Kconfig
> +++ b/drivers/uio/Kconfig
> @@ -94,4 +94,13 @@ config UIO_NETX
>  	  To compile this driver as a module, choose M here; the module
>  	  will be called uio_netx.
>  
> +config UIO_PRUSS
> +	tristate "Texas Instruments PRUSS driver"
> +	depends on ARCH_DAVINCI_DA850
> +	help
> +	  PRUSS driver for OMAPL138/DA850/AM18XX devices
> +	  PRUSS driver requires user space components

It would be nice to mention a link here where these user space components are
available.

> +	  To compile this driver as a module, choose M here: the module
> +	  will be called uio_pruss.
> +
>  endif
> diff --git a/drivers/uio/Makefile b/drivers/uio/Makefile
> index 18fd818..d4dd9a5 100644
> --- a/drivers/uio/Makefile
> +++ b/drivers/uio/Makefile
> @@ -6,3 +6,4 @@ obj-$(CONFIG_UIO_AEC)	+= uio_aec.o
>  obj-$(CONFIG_UIO_SERCOS3)	+= uio_sercos3.o
>  obj-$(CONFIG_UIO_PCI_GENERIC)	+= uio_pci_generic.o
>  obj-$(CONFIG_UIO_NETX)	+= uio_netx.o
> +obj-$(CONFIG_UIO_PRUSS)         += uio_pruss.o
> diff --git a/drivers/uio/uio_pruss.c b/drivers/uio/uio_pruss.c
> new file mode 100644
> index 0000000..b402197
> --- /dev/null
> +++ b/drivers/uio/uio_pruss.c
> @@ -0,0 +1,231 @@
> +/*
> + * Programmable Real-Time Unit Sub System (PRUSS) UIO driver (uio_pruss)
> + *
> + * This driver exports PRUSS host event out interrupts and PRUSS, L3 RAM,
> + * and DDR RAM to user space for applications interacting with PRUSS firmware
> + *
> + * Copyright (C) 2010-11 Texas Instruments Incorporated - http://www.ti.com/
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation version 2.
> + *
> + * This program is distributed "as is" WITHOUT ANY WARRANTY of any
> + * kind, whether express or implied; without even the implied warranty
> + * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + * GNU General Public License for more details.
> + */
> +#include <linux/device.h>
> +#include <linux/module.h>
> +#include <linux/platform_device.h>
> +#include <linux/uio_driver.h>
> +#include <linux/io.h>
> +#include <linux/clk.h>
> +#include <linux/dma-mapping.h>
> +#include <linux/slab.h>
> +
> +#define DRV_NAME "pruss"
> +#define DRV_VERSION "0.50"
> +
> +/*
> + * Host event IRQ numbers from PRUSS - PRUSS can generate upto 8 interrupt
> + * events to AINTC of ARM host processor - which can be used for IPC b/w PRUSS
> + * firmware and user space application, async notification from PRU firmware
> + * to user space application
> + * 3	PRU_EVTOUT0
> + * 4	PRU_EVTOUT1
> + * 5	PRU_EVTOUT2
> + * 6	PRU_EVTOUT3
> + * 7	PRU_EVTOUT4
> + * 8	PRU_EVTOUT5
> + * 9	PRU_EVTOUT6
> + * 10	PRU_EVTOUT7
> +*/
> +
> +#define MAX_PRUSS_EVTOUT_INSTANCE	8
> +
> +#define	PRUSS_INTC_HIPIR		0x4900
> +#define	PRUSS_INTC_HIPIR_INTPEND_MASK	0x80000000
> +#define	PRUSS_INTC_HIER			0x5500
> +
> +struct clk *pruss_clk;
> +struct uio_info *info;
> +void *ddr_virt_addr;
> +dma_addr_t ddr_phy_addr;
> +
> +static irqreturn_t pruss_handler(int irq, struct uio_info *dev_info)
> +{
> +	void __iomem *int_enable_reg = dev_info->mem[0].internal_addr
> +					+ PRUSS_INTC_HIER;
> +	void __iomem *int_status_reg = dev_info->mem[0].internal_addr
> +					+ PRUSS_INTC_HIPIR+((irq-1) << 2);

Blank line between variable definitions and code, please.

> +	/* Is interrupt enabled and active ? */
> +	if (!(ioread32(int_enable_reg) & (1<<(irq-1))) &&

Hmm. I'd prefer blanks around operands, like (1 << (irq - 1))).
I won't be too picky about that, noticing that checkpatch.pl doesn't complain.
If you want to do me a favor, you can fix it ;-)

> +		 (ioread32(int_status_reg) & PRUSS_INTC_HIPIR_INTPEND_MASK))
> +		return IRQ_NONE;
> +
> +	/* Disable interrupt */
> +	iowrite32(ioread32(int_enable_reg) & ~(1<<(irq-1)),

If you save the return value of the first ioread32(int_enable_reg) in a variable,
you don't need the second hardware access.

> +		int_enable_reg);
> +	return IRQ_HANDLED;
> +}
> +
> +static void pruss_cleanup(struct platform_device *dev, struct uio_info *info)
> +{
> +	int count;

Blank line between variable definitions and code, please.

> +	if (info) {
> +		for (count = 0; count < MAX_PRUSS_EVTOUT_INSTANCE; count++) {
> +			uio_unregister_device(&info[count]);
> +			kfree(info[count].name);
> +			iounmap(info[count].mem[0].internal_addr);
> +
> +		}
> +		if (ddr_virt_addr)
> +			dma_free_coherent(&dev->dev, info[0].mem[2].size,
> +					  info[0].mem[2].internal_addr,
> +					  info[0].mem[2].addr);
> +		kfree(info);
> +	}
> +	if (pruss_clk != NULL)
> +		clk_put(pruss_clk);
> +}
> +
> +static int __devinit pruss_probe(struct platform_device *dev)
> +{
> +	int ret = -ENODEV, count = 0;
> +	struct resource *regs_pruram, *regs_l3ram, *regs_ddr;
> +	char *string;
> +
> +	/* Power on PRU in case its not done as part of boot-loader */
> +	pruss_clk = clk_get(&dev->dev, "pruss");
> +	if (IS_ERR(pruss_clk)) {
> +		dev_err(&dev->dev, "Failed to get clock\n");
> +		ret = PTR_ERR(pruss_clk);
> +		return ret;
> +	} else {
> +		clk_enable(pruss_clk);
> +	}
> +
> +	info = kzalloc(sizeof(struct uio_info) * MAX_PRUSS_EVTOUT_INSTANCE,
> +		       GFP_KERNEL);
> +	if (info == NULL)

if (!info) looks better.

> +		return -ENOMEM;
> +
> +	regs_pruram = platform_get_resource(dev, IORESOURCE_MEM, 0);
> +	if (!regs_pruram) {
> +		dev_err(&dev->dev, "No memory resource specified\n");
> +		goto out_free;
> +	}
> +
> +	regs_l3ram = platform_get_resource(dev, IORESOURCE_MEM, 1);
> +	if (!regs_l3ram) {
> +		dev_err(&dev->dev, "No memory resource specified\n");
> +		goto out_free;
> +	}
> +
> +	regs_ddr = platform_get_resource(dev, IORESOURCE_MEM, 2);
> +	if (!regs_ddr) {
> +		dev_err(&dev->dev, "No memory resource specified\n");
> +		goto out_free;
> +	}
> +	ddr_virt_addr =
> +	    dma_alloc_coherent(&dev->dev, regs_ddr->end - regs_ddr->start + 1,
> +			       &ddr_phy_addr, GFP_KERNEL | GFP_DMA);
> +	if (!ddr_virt_addr) {
> +		dev_err(&dev->dev, "Could not allocate external memory\n");
> +		goto out_free;
> +	}
> +
> +	for (count = 0; count < MAX_PRUSS_EVTOUT_INSTANCE; count++) {
> +		info[count].mem[0].addr = regs_pruram->start;
> +		info[count].mem[0].size =
> +		    regs_pruram->end - regs_pruram->start + 1;
> +		if (!info[count].mem[0].addr ||
> +			!(info[count].mem[0].size - 1)) {
> +			dev_err(&dev->dev, "Invalid memory resource\n");
> +			goto out_free;
> +		}
> +		info[count].mem[0].internal_addr =
> +		    ioremap(regs_pruram->start, info[count].mem[0].size);
> +		if (!info[count].mem[0].internal_addr) {
> +			dev_err(&dev->dev,
> +				"Can't remap memory address range\n");
> +			goto out_free;
> +		}
> +		info[count].mem[0].memtype = UIO_MEM_PHYS;
> +
> +		info[count].mem[1].addr = regs_l3ram->start;
> +		info[count].mem[1].size =
> +		    regs_l3ram->end - regs_l3ram->start + 1;
> +		if (!info[count].mem[1].addr ||
> +			!(info[count].mem[1].size - 1)) {
> +			dev_err(&dev->dev, "Invalid memory resource\n");
> +			goto out_free;
> +		}
> +		info[count].mem[1].memtype = UIO_MEM_PHYS;
> +
> +		info[count].mem[2].internal_addr = ddr_virt_addr;
> +		info[count].mem[2].addr = ddr_phy_addr;
> +		info[count].mem[2].size = regs_ddr->end - regs_ddr->start + 1;
> +		info[count].mem[2].memtype = UIO_MEM_PHYS;
> +
> +		string = kzalloc(20, GFP_KERNEL);
> +		sprintf(string, "pruss_evt%d", count);
> +		info[count].name = string;
> +		info[count].version = "0.50";
> +
> +		/* Register PRUSS IRQ lines */
> +		info[count].irq = IRQ_DA8XX_EVTOUT0 + count;
> +
> +		info[count].irq_flags = 0;
> +		info[count].handler = pruss_handler;
> +
> +		ret = uio_register_device(&dev->dev, &info[count]);
> +
> +		if (ret < 0)
> +			goto out_free;
> +	}
> +
> +	platform_set_drvdata(dev, info);
> +	return 0;
> +
> +out_free:
> +	pruss_cleanup(dev, info);
> +	return ret;
> +}
> +
> +static int __devexit pruss_remove(struct platform_device *dev)
> +{
> +	struct uio_info *info = platform_get_drvdata(dev);

Blank line, please.

> +	pruss_cleanup(dev, info);
> +	platform_set_drvdata(dev, NULL);
> +	return 0;
> +}
> +
> +static struct platform_driver pruss_driver = {
> +	.probe = pruss_probe,
> +	.remove = __devexit_p(pruss_remove),
> +	.driver = {
> +		   .name = DRV_NAME,
> +		   .owner = THIS_MODULE,
> +		   },
> +};
> +
> +static int __init pruss_init_module(void)
> +{
> +	return platform_driver_register(&pruss_driver);
> +}
> +
> +module_init(pruss_init_module);
> +
> +static void __exit pruss_exit_module(void)
> +{
> +	platform_driver_unregister(&pruss_driver);
> +}
> +
> +module_exit(pruss_exit_module);
> +
> +MODULE_LICENSE("GPL v2");
> +MODULE_VERSION(DRV_VERSION);
> +MODULE_AUTHOR("Amit Chatterjee <amit.chatterjee@ti.com>");
> +MODULE_AUTHOR("Pratheesh Gangadhar <pratheesh@ti.com>");
> -- 
> 1.6.0.6
> 
>