[PATCH 0/2] ARM: OMAP4: fix MMC failure due to regulator enable/disable ops

[PATCH 0/2] ARM: OMAP4: fix MMC failure due to regulator enable/disable ops

[Balaji T K]

Balaji T K (2):
  ARM: OMAP4: MMC: increase delay for pbias
  ARM: OMAP4: MMC: no regulator off during probe for eMMC

 arch/arm/mach-omap2/board-4430sdp.c   |    1 +
 arch/arm/mach-omap2/hsmmc.c           |   16 +++++++++++++---
 arch/arm/mach-omap2/hsmmc.h           |    1 +
 arch/arm/plat-omap/include/plat/mmc.h |    3 +++
 drivers/mmc/host/omap_hsmmc.c         |    3 +++
 5 files changed, 21 insertions(+), 3 deletions(-)

[PATCH 0/2] ARM: OMAP4: fix MMC failure due to regulator enable/disable ops

[Balaji T K]

Balaji T K (2):
  ARM: OMAP4: MMC: increase delay for pbias
  ARM: OMAP4: MMC: no regulator off during probe for eMMC

 arch/arm/mach-omap2/board-4430sdp.c   |    1 +
 arch/arm/mach-omap2/hsmmc.c           |   16 +++++++++++++---
 arch/arm/mach-omap2/hsmmc.h           |    1 +
 arch/arm/plat-omap/include/plat/mmc.h |    3 +++
 drivers/mmc/host/omap_hsmmc.c         |    3 +++
 5 files changed, 21 insertions(+), 3 deletions(-)

[PATCH 1/2] ARM: OMAP4: MMC: increase delay for pbias

[Balaji T K]

4 micro seconds is not enough for PBIAS if MMC regulator is
enabled from MMC regulator OFF.
Increase the delay for PBIAS to stabilize.
Wait for PBIAS and timeout if not.

Resolves MMC/SD failure on OMAP4
"Pbias Voltage is not same as LDO"

Signed-off-by: Balaji T K <balajitk@ti.com>
---
 arch/arm/mach-omap2/hsmmc.c |   13 ++++++++++---
 1 files changed, 10 insertions(+), 3 deletions(-)

diff --git a/arch/arm/mach-omap2/hsmmc.c b/arch/arm/mach-omap2/hsmmc.c
index b2f30be..3f8dc16 100644
--- a/arch/arm/mach-omap2/hsmmc.c
+++ b/arch/arm/mach-omap2/hsmmc.c
@@ -145,6 +145,7 @@ static void omap4_hsmmc1_after_set_reg(struct device *dev, int slot,
 				 int power_on, int vdd)
 {
 	u32 reg;
+	unsigned long timeout;
 
 	if (power_on) {
 		reg = omap4_ctrl_pad_readl(control_pbias_offset);
@@ -157,9 +158,15 @@ static void omap4_hsmmc1_after_set_reg(struct device *dev, int slot,
 			OMAP4_MMC1_PWRDNZ_MASK |
 			OMAP4_USBC1_ICUSB_PWRDNZ_MASK);
 		omap4_ctrl_pad_writel(reg, control_pbias_offset);
-		/* 4 microsec delay for comparator to generate an error*/
-		udelay(4);
-		reg = omap4_ctrl_pad_readl(control_pbias_offset);
+
+		timeout = jiffies + msecs_to_jiffies(5);
+		do {
+			reg = omap4_ctrl_pad_readl(control_pbias_offset);
+			if (!(reg & OMAP4_MMC1_PBIASLITE_VMODE_ERROR_MASK))
+				break;
+			udelay(100);
+		} while (!time_after(jiffies, timeout));
+
 		if (reg & OMAP4_MMC1_PBIASLITE_VMODE_ERROR_MASK) {
 			pr_err("Pbias Voltage is not same as LDO\n");
 			/* Caution : On VMODE_ERROR Power Down MMC IO */
-- 
1.7.0.4

[PATCH 1/2] ARM: OMAP4: MMC: increase delay for pbias

[Balaji T K]

4 micro seconds is not enough for PBIAS if MMC regulator is
enabled from MMC regulator OFF.
Increase the delay for PBIAS to stabilize.
Wait for PBIAS and timeout if not.

Resolves MMC/SD failure on OMAP4
"Pbias Voltage is not same as LDO"

Signed-off-by: Balaji T K <balajitk@ti.com>
---
 arch/arm/mach-omap2/hsmmc.c |   13 ++++++++++---
 1 files changed, 10 insertions(+), 3 deletions(-)

diff --git a/arch/arm/mach-omap2/hsmmc.c b/arch/arm/mach-omap2/hsmmc.c
index b2f30be..3f8dc16 100644
--- a/arch/arm/mach-omap2/hsmmc.c
+++ b/arch/arm/mach-omap2/hsmmc.c
@@ -145,6 +145,7 @@ static void omap4_hsmmc1_after_set_reg(struct device *dev, int slot,
 				 int power_on, int vdd)
 {
 	u32 reg;
+	unsigned long timeout;
 
 	if (power_on) {
 		reg = omap4_ctrl_pad_readl(control_pbias_offset);
@@ -157,9 +158,15 @@ static void omap4_hsmmc1_after_set_reg(struct device *dev, int slot,
 			OMAP4_MMC1_PWRDNZ_MASK |
 			OMAP4_USBC1_ICUSB_PWRDNZ_MASK);
 		omap4_ctrl_pad_writel(reg, control_pbias_offset);
-		/* 4 microsec delay for comparator to generate an error*/
-		udelay(4);
-		reg = omap4_ctrl_pad_readl(control_pbias_offset);
+
+		timeout = jiffies + msecs_to_jiffies(5);
+		do {
+			reg = omap4_ctrl_pad_readl(control_pbias_offset);
+			if (!(reg & OMAP4_MMC1_PBIASLITE_VMODE_ERROR_MASK))
+				break;
+			udelay(100);
+		} while (!time_after(jiffies, timeout));
+
 		if (reg & OMAP4_MMC1_PBIASLITE_VMODE_ERROR_MASK) {
 			pr_err("Pbias Voltage is not same as LDO\n");
 			/* Caution : On VMODE_ERROR Power Down MMC IO */
-- 
1.7.0.4

Re: [PATCH 1/2] ARM: OMAP4: MMC: increase delay for pbias

[Tony Lindgren]

* Balaji T K <balajitk@ti.com> [110530 07:23]:
> 4 micro seconds is not enough for PBIAS if MMC regulator is
> enabled from MMC regulator OFF.
> Increase the delay for PBIAS to stabilize.
> Wait for PBIAS and timeout if not.
> 
> Resolves MMC/SD failure on OMAP4
> "Pbias Voltage is not same as LDO"

Thanks will queue as a fix.

Tony

[PATCH 1/2] ARM: OMAP4: MMC: increase delay for pbias

[Tony Lindgren]

* Balaji T K <balajitk@ti.com> [110530 07:23]:
> 4 micro seconds is not enough for PBIAS if MMC regulator is
> enabled from MMC regulator OFF.
> Increase the delay for PBIAS to stabilize.
> Wait for PBIAS and timeout if not.
> 
> Resolves MMC/SD failure on OMAP4
> "Pbias Voltage is not same as LDO"

Thanks will queue as a fix.

Tony

Re: [PATCH 1/2] ARM: OMAP4: MMC: increase delay for pbias

[Kishore Kadiyala]

On Mon, May 30, 2011 at 7:55 PM, Balaji T K <balajitk@ti.com> wrote:
> 4 micro seconds is not enough for PBIAS if MMC regulator is
> enabled from MMC regulator OFF.
> Increase the delay for PBIAS to stabilize.
> Wait for PBIAS and timeout if not.
>
> Resolves MMC/SD failure on OMAP4
> "Pbias Voltage is not same as LDO"
>
> Signed-off-by: Balaji T K <balajitk@ti.com>

Acked-by:  Kishore Kadiyala <kishore.kadiyala@ti.com>

<snip>

[PATCH 1/2] ARM: OMAP4: MMC: increase delay for pbias

[Kishore Kadiyala]

On Mon, May 30, 2011 at 7:55 PM, Balaji T K <balajitk@ti.com> wrote:
> 4 micro seconds is not enough for PBIAS if MMC regulator is
> enabled from MMC regulator OFF.
> Increase the delay for PBIAS to stabilize.
> Wait for PBIAS and timeout if not.
>
> Resolves MMC/SD failure on OMAP4
> "Pbias Voltage is not same as LDO"
>
> Signed-off-by: Balaji T K <balajitk@ti.com>

Acked-by:  Kishore Kadiyala <kishore.kadiyala@ti.com>

<snip>

Re: [PATCH 1/2] ARM: OMAP4: MMC: increase delay for pbias

[Tony Lindgren]

* Balaji T K <balajitk@ti.com> [110530 07:23]:
> 4 micro seconds is not enough for PBIAS if MMC regulator is
> enabled from MMC regulator OFF.
> Increase the delay for PBIAS to stabilize.
> Wait for PBIAS and timeout if not.
> 
> Resolves MMC/SD failure on OMAP4
> "Pbias Voltage is not same as LDO"
> 
> Signed-off-by: Balaji T K <balajitk@ti.com>
> ---
>  arch/arm/mach-omap2/hsmmc.c |   13 ++++++++++---
>  1 files changed, 10 insertions(+), 3 deletions(-)
> 
> diff --git a/arch/arm/mach-omap2/hsmmc.c b/arch/arm/mach-omap2/hsmmc.c
> index b2f30be..3f8dc16 100644
> --- a/arch/arm/mach-omap2/hsmmc.c
> +++ b/arch/arm/mach-omap2/hsmmc.c
> @@ -145,6 +145,7 @@ static void omap4_hsmmc1_after_set_reg(struct device *dev, int slot,
>  				 int power_on, int vdd)
>  {
>  	u32 reg;
> +	unsigned long timeout;
>  
>  	if (power_on) {
>  		reg = omap4_ctrl_pad_readl(control_pbias_offset);
> @@ -157,9 +158,15 @@ static void omap4_hsmmc1_after_set_reg(struct device *dev, int slot,
>  			OMAP4_MMC1_PWRDNZ_MASK |
>  			OMAP4_USBC1_ICUSB_PWRDNZ_MASK);
>  		omap4_ctrl_pad_writel(reg, control_pbias_offset);
> -		/* 4 microsec delay for comparator to generate an error*/
> -		udelay(4);
> -		reg = omap4_ctrl_pad_readl(control_pbias_offset);
> +
> +		timeout = jiffies + msecs_to_jiffies(5);
> +		do {
> +			reg = omap4_ctrl_pad_readl(control_pbias_offset);
> +			if (!(reg & OMAP4_MMC1_PBIASLITE_VMODE_ERROR_MASK))
> +				break;
> +			udelay(100);
> +		} while (!time_after(jiffies, timeout));
> +
>  		if (reg & OMAP4_MMC1_PBIASLITE_VMODE_ERROR_MASK) {
>  			pr_err("Pbias Voltage is not same as LDO\n");
>  			/* Caution : On VMODE_ERROR Power Down MMC IO */

Actually, can you check if you can use usleep_range here as recommended
by checkpatch.pl?

Tony

[PATCH 1/2] ARM: OMAP4: MMC: increase delay for pbias

[Tony Lindgren]

* Balaji T K <balajitk@ti.com> [110530 07:23]:
> 4 micro seconds is not enough for PBIAS if MMC regulator is
> enabled from MMC regulator OFF.
> Increase the delay for PBIAS to stabilize.
> Wait for PBIAS and timeout if not.
> 
> Resolves MMC/SD failure on OMAP4
> "Pbias Voltage is not same as LDO"
> 
> Signed-off-by: Balaji T K <balajitk@ti.com>
> ---
>  arch/arm/mach-omap2/hsmmc.c |   13 ++++++++++---
>  1 files changed, 10 insertions(+), 3 deletions(-)
> 
> diff --git a/arch/arm/mach-omap2/hsmmc.c b/arch/arm/mach-omap2/hsmmc.c
> index b2f30be..3f8dc16 100644
> --- a/arch/arm/mach-omap2/hsmmc.c
> +++ b/arch/arm/mach-omap2/hsmmc.c
> @@ -145,6 +145,7 @@ static void omap4_hsmmc1_after_set_reg(struct device *dev, int slot,
>  				 int power_on, int vdd)
>  {
>  	u32 reg;
> +	unsigned long timeout;
>  
>  	if (power_on) {
>  		reg = omap4_ctrl_pad_readl(control_pbias_offset);
> @@ -157,9 +158,15 @@ static void omap4_hsmmc1_after_set_reg(struct device *dev, int slot,
>  			OMAP4_MMC1_PWRDNZ_MASK |
>  			OMAP4_USBC1_ICUSB_PWRDNZ_MASK);
>  		omap4_ctrl_pad_writel(reg, control_pbias_offset);
> -		/* 4 microsec delay for comparator to generate an error*/
> -		udelay(4);
> -		reg = omap4_ctrl_pad_readl(control_pbias_offset);
> +
> +		timeout = jiffies + msecs_to_jiffies(5);
> +		do {
> +			reg = omap4_ctrl_pad_readl(control_pbias_offset);
> +			if (!(reg & OMAP4_MMC1_PBIASLITE_VMODE_ERROR_MASK))
> +				break;
> +			udelay(100);
> +		} while (!time_after(jiffies, timeout));
> +
>  		if (reg & OMAP4_MMC1_PBIASLITE_VMODE_ERROR_MASK) {
>  			pr_err("Pbias Voltage is not same as LDO\n");
>  			/* Caution : On VMODE_ERROR Power Down MMC IO */

Actually, can you check if you can use usleep_range here as recommended
by checkpatch.pl?

Tony

Re: [PATCH 1/2] ARM: OMAP4: MMC: increase delay for pbias

[T Krishnamoorthy, Balaji]

On Wed, Jun 1, 2011 at 1:11 PM, Tony Lindgren <tony@atomide.com> wrote:
> * Balaji T K <balajitk@ti.com> [110530 07:23]:
>> 4 micro seconds is not enough for PBIAS if MMC regulator is
>> enabled from MMC regulator OFF.
>> Increase the delay for PBIAS to stabilize.
>> Wait for PBIAS and timeout if not.
>>
>> Resolves MMC/SD failure on OMAP4
>> "Pbias Voltage is not same as LDO"
>>
>> Signed-off-by: Balaji T K <balajitk@ti.com>
>> ---
>>  arch/arm/mach-omap2/hsmmc.c |   13 ++++++++++---
>>  1 files changed, 10 insertions(+), 3 deletions(-)
>>
>> diff --git a/arch/arm/mach-omap2/hsmmc.c b/arch/arm/mach-omap2/hsmmc.c
>> index b2f30be..3f8dc16 100644
>> --- a/arch/arm/mach-omap2/hsmmc.c
>> +++ b/arch/arm/mach-omap2/hsmmc.c
>> @@ -145,6 +145,7 @@ static void omap4_hsmmc1_after_set_reg(struct device *dev, int slot,
>>                                int power_on, int vdd)
>>  {
>>       u32 reg;
>> +     unsigned long timeout;
>>
>>       if (power_on) {
>>               reg = omap4_ctrl_pad_readl(control_pbias_offset);
>> @@ -157,9 +158,15 @@ static void omap4_hsmmc1_after_set_reg(struct device *dev, int slot,
>>                       OMAP4_MMC1_PWRDNZ_MASK |
>>                       OMAP4_USBC1_ICUSB_PWRDNZ_MASK);
>>               omap4_ctrl_pad_writel(reg, control_pbias_offset);
>> -             /* 4 microsec delay for comparator to generate an error*/
>> -             udelay(4);
>> -             reg = omap4_ctrl_pad_readl(control_pbias_offset);
>> +
>> +             timeout = jiffies + msecs_to_jiffies(5);
>> +             do {
>> +                     reg = omap4_ctrl_pad_readl(control_pbias_offset);
>> +                     if (!(reg & OMAP4_MMC1_PBIASLITE_VMODE_ERROR_MASK))
>> +                             break;
>> +                     udelay(100);
>> +             } while (!time_after(jiffies, timeout));
>> +
>>               if (reg & OMAP4_MMC1_PBIASLITE_VMODE_ERROR_MASK) {
>>                       pr_err("Pbias Voltage is not same as LDO\n");
>>                       /* Caution : On VMODE_ERROR Power Down MMC IO */
>
> Actually, can you check if you can use usleep_range here as recommended
> by checkpatch.pl?

sure, fixing it in v2

>
> Tony
>

[PATCH 1/2] ARM: OMAP4: MMC: increase delay for pbias

[T Krishnamoorthy, Balaji]

On Wed, Jun 1, 2011 at 1:11 PM, Tony Lindgren <tony@atomide.com> wrote:
> * Balaji T K <balajitk@ti.com> [110530 07:23]:
>> 4 micro seconds is not enough for PBIAS if MMC regulator is
>> enabled from MMC regulator OFF.
>> Increase the delay for PBIAS to stabilize.
>> Wait for PBIAS and timeout if not.
>>
>> Resolves MMC/SD failure on OMAP4
>> "Pbias Voltage is not same as LDO"
>>
>> Signed-off-by: Balaji T K <balajitk@ti.com>
>> ---
>> ?arch/arm/mach-omap2/hsmmc.c | ? 13 ++++++++++---
>> ?1 files changed, 10 insertions(+), 3 deletions(-)
>>
>> diff --git a/arch/arm/mach-omap2/hsmmc.c b/arch/arm/mach-omap2/hsmmc.c
>> index b2f30be..3f8dc16 100644
>> --- a/arch/arm/mach-omap2/hsmmc.c
>> +++ b/arch/arm/mach-omap2/hsmmc.c
>> @@ -145,6 +145,7 @@ static void omap4_hsmmc1_after_set_reg(struct device *dev, int slot,
>> ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?int power_on, int vdd)
>> ?{
>> ? ? ? u32 reg;
>> + ? ? unsigned long timeout;
>>
>> ? ? ? if (power_on) {
>> ? ? ? ? ? ? ? reg = omap4_ctrl_pad_readl(control_pbias_offset);
>> @@ -157,9 +158,15 @@ static void omap4_hsmmc1_after_set_reg(struct device *dev, int slot,
>> ? ? ? ? ? ? ? ? ? ? ? OMAP4_MMC1_PWRDNZ_MASK |
>> ? ? ? ? ? ? ? ? ? ? ? OMAP4_USBC1_ICUSB_PWRDNZ_MASK);
>> ? ? ? ? ? ? ? omap4_ctrl_pad_writel(reg, control_pbias_offset);
>> - ? ? ? ? ? ? /* 4 microsec delay for comparator to generate an error*/
>> - ? ? ? ? ? ? udelay(4);
>> - ? ? ? ? ? ? reg = omap4_ctrl_pad_readl(control_pbias_offset);
>> +
>> + ? ? ? ? ? ? timeout = jiffies + msecs_to_jiffies(5);
>> + ? ? ? ? ? ? do {
>> + ? ? ? ? ? ? ? ? ? ? reg = omap4_ctrl_pad_readl(control_pbias_offset);
>> + ? ? ? ? ? ? ? ? ? ? if (!(reg & OMAP4_MMC1_PBIASLITE_VMODE_ERROR_MASK))
>> + ? ? ? ? ? ? ? ? ? ? ? ? ? ? break;
>> + ? ? ? ? ? ? ? ? ? ? udelay(100);
>> + ? ? ? ? ? ? } while (!time_after(jiffies, timeout));
>> +
>> ? ? ? ? ? ? ? if (reg & OMAP4_MMC1_PBIASLITE_VMODE_ERROR_MASK) {
>> ? ? ? ? ? ? ? ? ? ? ? pr_err("Pbias Voltage is not same as LDO\n");
>> ? ? ? ? ? ? ? ? ? ? ? /* Caution : On VMODE_ERROR Power Down MMC IO */
>
> Actually, can you check if you can use usleep_range here as recommended
> by checkpatch.pl?

sure, fixing it in v2

>
> Tony
>

[PATCH 2/2] ARM: OMAP4: MMC: no regulator off during probe for eMMC

[Balaji T K]

eMMC does not handle power off when not in sleep state,
Skip regulator disable during probe when eMMC is
not in known state - state left by bootloader.

Resolves eMMC failure on OMAP4
mmc0: error -110 whilst initialising MMC card

Signed-off-by: Balaji T K <balajitk@ti.com>
---
 arch/arm/mach-omap2/board-4430sdp.c   |    1 +
 arch/arm/mach-omap2/hsmmc.c           |    3 +++
 arch/arm/mach-omap2/hsmmc.h           |    1 +
 arch/arm/plat-omap/include/plat/mmc.h |    3 +++
 drivers/mmc/host/omap_hsmmc.c         |    3 +++
 5 files changed, 11 insertions(+), 0 deletions(-)

diff --git a/arch/arm/mach-omap2/board-4430sdp.c b/arch/arm/mach-omap2/board-4430sdp.c
index 73fa90b..b324605 100644
--- a/arch/arm/mach-omap2/board-4430sdp.c
+++ b/arch/arm/mach-omap2/board-4430sdp.c
@@ -322,6 +322,7 @@ static struct omap2_hsmmc_info mmc[] = {
 		.gpio_wp	= -EINVAL,
 		.nonremovable   = true,
 		.ocr_mask	= MMC_VDD_29_30,
+		.no_off_init	= true,
 	},
 	{
 		.mmc		= 1,
diff --git a/arch/arm/mach-omap2/hsmmc.c b/arch/arm/mach-omap2/hsmmc.c
index 3f8dc16..28ca144 100644
--- a/arch/arm/mach-omap2/hsmmc.c
+++ b/arch/arm/mach-omap2/hsmmc.c
@@ -338,6 +338,9 @@ static int __init omap_hsmmc_pdata_init(struct omap2_hsmmc_info *c,
 	if (c->no_off)
 		mmc->slots[0].no_off = 1;
 
+	if (c->no_off_init)
+		mmc->slots[0].no_regulator_off_init = c->no_off_init;
+
 	if (c->vcc_aux_disable_is_sleep)
 		mmc->slots[0].vcc_aux_disable_is_sleep = 1;
 
diff --git a/arch/arm/mach-omap2/hsmmc.h b/arch/arm/mach-omap2/hsmmc.h
index f119348..f757e78 100644
--- a/arch/arm/mach-omap2/hsmmc.h
+++ b/arch/arm/mach-omap2/hsmmc.h
@@ -18,6 +18,7 @@ struct omap2_hsmmc_info {
 	bool	nonremovable;	/* Nonremovable e.g. eMMC */
 	bool	power_saving;	/* Try to sleep or power off when possible */
 	bool	no_off;		/* power_saving and power is not to go off */
+	bool	no_off_init;	/* no power off when not in MMC sleep state */
 	bool	vcc_aux_disable_is_sleep; /* Regulator off remapped to sleep */
 	int	gpio_cd;	/* or -EINVAL */
 	int	gpio_wp;	/* or -EINVAL */
diff --git a/arch/arm/plat-omap/include/plat/mmc.h b/arch/arm/plat-omap/include/plat/mmc.h
index f38fef9..c7b8741 100644
--- a/arch/arm/plat-omap/include/plat/mmc.h
+++ b/arch/arm/plat-omap/include/plat/mmc.h
@@ -101,6 +101,9 @@ struct omap_mmc_platform_data {
 		/* If using power_saving and the MMC power is not to go off */
 		unsigned no_off:1;
 
+		/* eMMC does not handle power off when not in sleep state */
+		unsigned no_regulator_off_init:1;
+
 		/* Regulator off remapped to sleep */
 		unsigned vcc_aux_disable_is_sleep:1;
 
diff --git a/drivers/mmc/host/omap_hsmmc.c b/drivers/mmc/host/omap_hsmmc.c
index 259ece0..5b2e215 100644
--- a/drivers/mmc/host/omap_hsmmc.c
+++ b/drivers/mmc/host/omap_hsmmc.c
@@ -435,6 +435,9 @@ static int omap_hsmmc_reg_get(struct omap_hsmmc_host *host)
 		reg = regulator_get(host->dev, "vmmc_aux");
 		host->vcc_aux = IS_ERR(reg) ? NULL : reg;
 
+		/* For eMMC do not power off when not in sleep state */
+		if (mmc_slot(host).no_regulator_off_init)
+			return 0;
 		/*
 		* UGLY HACK:  workaround regulator framework bugs.
 		* When the bootloader leaves a supply active, it's
-- 
1.7.0.4

[PATCH 2/2] ARM: OMAP4: MMC: no regulator off during probe for eMMC

[Balaji T K]

eMMC does not handle power off when not in sleep state,
Skip regulator disable during probe when eMMC is
not in known state - state left by bootloader.

Resolves eMMC failure on OMAP4
mmc0: error -110 whilst initialising MMC card

Signed-off-by: Balaji T K <balajitk@ti.com>
---
 arch/arm/mach-omap2/board-4430sdp.c   |    1 +
 arch/arm/mach-omap2/hsmmc.c           |    3 +++
 arch/arm/mach-omap2/hsmmc.h           |    1 +
 arch/arm/plat-omap/include/plat/mmc.h |    3 +++
 drivers/mmc/host/omap_hsmmc.c         |    3 +++
 5 files changed, 11 insertions(+), 0 deletions(-)

diff --git a/arch/arm/mach-omap2/board-4430sdp.c b/arch/arm/mach-omap2/board-4430sdp.c
index 73fa90b..b324605 100644
--- a/arch/arm/mach-omap2/board-4430sdp.c
+++ b/arch/arm/mach-omap2/board-4430sdp.c
@@ -322,6 +322,7 @@ static struct omap2_hsmmc_info mmc[] = {
 		.gpio_wp	= -EINVAL,
 		.nonremovable   = true,
 		.ocr_mask	= MMC_VDD_29_30,
+		.no_off_init	= true,
 	},
 	{
 		.mmc		= 1,
diff --git a/arch/arm/mach-omap2/hsmmc.c b/arch/arm/mach-omap2/hsmmc.c
index 3f8dc16..28ca144 100644
--- a/arch/arm/mach-omap2/hsmmc.c
+++ b/arch/arm/mach-omap2/hsmmc.c
@@ -338,6 +338,9 @@ static int __init omap_hsmmc_pdata_init(struct omap2_hsmmc_info *c,
 	if (c->no_off)
 		mmc->slots[0].no_off = 1;
 
+	if (c->no_off_init)
+		mmc->slots[0].no_regulator_off_init = c->no_off_init;
+
 	if (c->vcc_aux_disable_is_sleep)
 		mmc->slots[0].vcc_aux_disable_is_sleep = 1;
 
diff --git a/arch/arm/mach-omap2/hsmmc.h b/arch/arm/mach-omap2/hsmmc.h
index f119348..f757e78 100644
--- a/arch/arm/mach-omap2/hsmmc.h
+++ b/arch/arm/mach-omap2/hsmmc.h
@@ -18,6 +18,7 @@ struct omap2_hsmmc_info {
 	bool	nonremovable;	/* Nonremovable e.g. eMMC */
 	bool	power_saving;	/* Try to sleep or power off when possible */
 	bool	no_off;		/* power_saving and power is not to go off */
+	bool	no_off_init;	/* no power off when not in MMC sleep state */
 	bool	vcc_aux_disable_is_sleep; /* Regulator off remapped to sleep */
 	int	gpio_cd;	/* or -EINVAL */
 	int	gpio_wp;	/* or -EINVAL */
diff --git a/arch/arm/plat-omap/include/plat/mmc.h b/arch/arm/plat-omap/include/plat/mmc.h
index f38fef9..c7b8741 100644
--- a/arch/arm/plat-omap/include/plat/mmc.h
+++ b/arch/arm/plat-omap/include/plat/mmc.h
@@ -101,6 +101,9 @@ struct omap_mmc_platform_data {
 		/* If using power_saving and the MMC power is not to go off */
 		unsigned no_off:1;
 
+		/* eMMC does not handle power off when not in sleep state */
+		unsigned no_regulator_off_init:1;
+
 		/* Regulator off remapped to sleep */
 		unsigned vcc_aux_disable_is_sleep:1;
 
diff --git a/drivers/mmc/host/omap_hsmmc.c b/drivers/mmc/host/omap_hsmmc.c
index 259ece0..5b2e215 100644
--- a/drivers/mmc/host/omap_hsmmc.c
+++ b/drivers/mmc/host/omap_hsmmc.c
@@ -435,6 +435,9 @@ static int omap_hsmmc_reg_get(struct omap_hsmmc_host *host)
 		reg = regulator_get(host->dev, "vmmc_aux");
 		host->vcc_aux = IS_ERR(reg) ? NULL : reg;
 
+		/* For eMMC do not power off when not in sleep state */
+		if (mmc_slot(host).no_regulator_off_init)
+			return 0;
 		/*
 		* UGLY HACK:  workaround regulator framework bugs.
 		* When the bootloader leaves a supply active, it's
-- 
1.7.0.4

Re: [PATCH 2/2] ARM: OMAP4: MMC: no regulator off during probe for eMMC

[Tony Lindgren]

* Balaji T K <balajitk@ti.com> [110530 07:23]:
> eMMC does not handle power off when not in sleep state,
> Skip regulator disable during probe when eMMC is
> not in known state - state left by bootloader.
> 
> Resolves eMMC failure on OMAP4
> mmc0: error -110 whilst initialising MMC card
> 
> --- a/arch/arm/mach-omap2/hsmmc.h
> +++ b/arch/arm/mach-omap2/hsmmc.h
> @@ -18,6 +18,7 @@ struct omap2_hsmmc_info {
>  	bool	nonremovable;	/* Nonremovable e.g. eMMC */
>  	bool	power_saving;	/* Try to sleep or power off when possible */
>  	bool	no_off;		/* power_saving and power is not to go off */
> +	bool	no_off_init;	/* no power off when not in MMC sleep state */
>  	bool	vcc_aux_disable_is_sleep; /* Regulator off remapped to sleep */
>  	int	gpio_cd;	/* or -EINVAL */
>  	int	gpio_wp;	/* or -EINVAL */

Can't you use no_off for this too?

Tony

[PATCH 2/2] ARM: OMAP4: MMC: no regulator off during probe for eMMC

[Tony Lindgren]

* Balaji T K <balajitk@ti.com> [110530 07:23]:
> eMMC does not handle power off when not in sleep state,
> Skip regulator disable during probe when eMMC is
> not in known state - state left by bootloader.
> 
> Resolves eMMC failure on OMAP4
> mmc0: error -110 whilst initialising MMC card
> 
> --- a/arch/arm/mach-omap2/hsmmc.h
> +++ b/arch/arm/mach-omap2/hsmmc.h
> @@ -18,6 +18,7 @@ struct omap2_hsmmc_info {
>  	bool	nonremovable;	/* Nonremovable e.g. eMMC */
>  	bool	power_saving;	/* Try to sleep or power off when possible */
>  	bool	no_off;		/* power_saving and power is not to go off */
> +	bool	no_off_init;	/* no power off when not in MMC sleep state */
>  	bool	vcc_aux_disable_is_sleep; /* Regulator off remapped to sleep */
>  	int	gpio_cd;	/* or -EINVAL */
>  	int	gpio_wp;	/* or -EINVAL */

Can't you use no_off for this too?

Tony

Re: [PATCH 2/2] ARM: OMAP4: MMC: no regulator off during probe for eMMC

[T Krishnamoorthy, Balaji]

On Tue, May 31, 2011 at 6:56 PM, Tony Lindgren <tony@atomide.com> wrote:
> * Balaji T K <balajitk@ti.com> [110530 07:23]:
>> eMMC does not handle power off when not in sleep state,
>> Skip regulator disable during probe when eMMC is
>> not in known state - state left by bootloader.
>>
>> Resolves eMMC failure on OMAP4
>> mmc0: error -110 whilst initialising MMC card
>>
>> --- a/arch/arm/mach-omap2/hsmmc.h
>> +++ b/arch/arm/mach-omap2/hsmmc.h
>> @@ -18,6 +18,7 @@ struct omap2_hsmmc_info {
>>       bool    nonremovable;   /* Nonremovable e.g. eMMC */
>>       bool    power_saving;   /* Try to sleep or power off when possible */
>>       bool    no_off;         /* power_saving and power is not to go off */
>> +     bool    no_off_init;    /* no power off when not in MMC sleep state */
>>       bool    vcc_aux_disable_is_sleep; /* Regulator off remapped to sleep */
>>       int     gpio_cd;        /* or -EINVAL */
>>       int     gpio_wp;        /* or -EINVAL */
>
> Can't you use no_off for this too?

no_off is used for devices which do not want to disable regulator at any time.

newly introduced no_off_init is to skip disable regulator only during probe
After eMMC is put in sleep state (while suspend), regulator for eMMC
(VAUX1) can be disabled.

-- 
Thanks and Regards,
Balaji T K

>
> Tony
>

[PATCH 2/2] ARM: OMAP4: MMC: no regulator off during probe for eMMC

[T Krishnamoorthy, Balaji]

On Tue, May 31, 2011 at 6:56 PM, Tony Lindgren <tony@atomide.com> wrote:
> * Balaji T K <balajitk@ti.com> [110530 07:23]:
>> eMMC does not handle power off when not in sleep state,
>> Skip regulator disable during probe when eMMC is
>> not in known state - state left by bootloader.
>>
>> Resolves eMMC failure on OMAP4
>> mmc0: error -110 whilst initialising MMC card
>>
>> --- a/arch/arm/mach-omap2/hsmmc.h
>> +++ b/arch/arm/mach-omap2/hsmmc.h
>> @@ -18,6 +18,7 @@ struct omap2_hsmmc_info {
>> ? ? ? bool ? ?nonremovable; ? /* Nonremovable e.g. eMMC */
>> ? ? ? bool ? ?power_saving; ? /* Try to sleep or power off when possible */
>> ? ? ? bool ? ?no_off; ? ? ? ? /* power_saving and power is not to go off */
>> + ? ? bool ? ?no_off_init; ? ?/* no power off when not in MMC sleep state */
>> ? ? ? bool ? ?vcc_aux_disable_is_sleep; /* Regulator off remapped to sleep */
>> ? ? ? int ? ? gpio_cd; ? ? ? ?/* or -EINVAL */
>> ? ? ? int ? ? gpio_wp; ? ? ? ?/* or -EINVAL */
>
> Can't you use no_off for this too?

no_off is used for devices which do not want to disable regulator at any time.

newly introduced no_off_init is to skip disable regulator only during probe
After eMMC is put in sleep state (while suspend), regulator for eMMC
(VAUX1) can be disabled.

-- 
Thanks and Regards,
Balaji T K

>
> Tony
>

Re: [PATCH 2/2] ARM: OMAP4: MMC: no regulator off during probe for eMMC

[Tony Lindgren]

* T Krishnamoorthy, Balaji <balajitk@ti.com> [110531 06:28]:
> On Tue, May 31, 2011 at 6:56 PM, Tony Lindgren <tony@atomide.com> wrote:
> > * Balaji T K <balajitk@ti.com> [110530 07:23]:
> >> eMMC does not handle power off when not in sleep state,
> >> Skip regulator disable during probe when eMMC is
> >> not in known state - state left by bootloader.
> >>
> >> Resolves eMMC failure on OMAP4
> >> mmc0: error -110 whilst initialising MMC card
> >>
> >> --- a/arch/arm/mach-omap2/hsmmc.h
> >> +++ b/arch/arm/mach-omap2/hsmmc.h
> >> @@ -18,6 +18,7 @@ struct omap2_hsmmc_info {
> >>       bool    nonremovable;   /* Nonremovable e.g. eMMC */
> >>       bool    power_saving;   /* Try to sleep or power off when possible */
> >>       bool    no_off;         /* power_saving and power is not to go off */
> >> +     bool    no_off_init;    /* no power off when not in MMC sleep state */
> >>       bool    vcc_aux_disable_is_sleep; /* Regulator off remapped to sleep */
> >>       int     gpio_cd;        /* or -EINVAL */
> >>       int     gpio_wp;        /* or -EINVAL */
> >
> > Can't you use no_off for this too?
> 
> no_off is used for devices which do not want to disable regulator at any time.
> 
> newly introduced no_off_init is to skip disable regulator only during probe
> After eMMC is put in sleep state (while suspend), regulator for eMMC
> (VAUX1) can be disabled.

OK I'll queue this as a fix too then. Anybody from the MMC list care
to ack?

Tony

[PATCH 2/2] ARM: OMAP4: MMC: no regulator off during probe for eMMC

[Tony Lindgren]

* T Krishnamoorthy, Balaji <balajitk@ti.com> [110531 06:28]:
> On Tue, May 31, 2011 at 6:56 PM, Tony Lindgren <tony@atomide.com> wrote:
> > * Balaji T K <balajitk@ti.com> [110530 07:23]:
> >> eMMC does not handle power off when not in sleep state,
> >> Skip regulator disable during probe when eMMC is
> >> not in known state - state left by bootloader.
> >>
> >> Resolves eMMC failure on OMAP4
> >> mmc0: error -110 whilst initialising MMC card
> >>
> >> --- a/arch/arm/mach-omap2/hsmmc.h
> >> +++ b/arch/arm/mach-omap2/hsmmc.h
> >> @@ -18,6 +18,7 @@ struct omap2_hsmmc_info {
> >> ? ? ? bool ? ?nonremovable; ? /* Nonremovable e.g. eMMC */
> >> ? ? ? bool ? ?power_saving; ? /* Try to sleep or power off when possible */
> >> ? ? ? bool ? ?no_off; ? ? ? ? /* power_saving and power is not to go off */
> >> + ? ? bool ? ?no_off_init; ? ?/* no power off when not in MMC sleep state */
> >> ? ? ? bool ? ?vcc_aux_disable_is_sleep; /* Regulator off remapped to sleep */
> >> ? ? ? int ? ? gpio_cd; ? ? ? ?/* or -EINVAL */
> >> ? ? ? int ? ? gpio_wp; ? ? ? ?/* or -EINVAL */
> >
> > Can't you use no_off for this too?
> 
> no_off is used for devices which do not want to disable regulator at any time.
> 
> newly introduced no_off_init is to skip disable regulator only during probe
> After eMMC is put in sleep state (while suspend), regulator for eMMC
> (VAUX1) can be disabled.

OK I'll queue this as a fix too then. Anybody from the MMC list care
to ack?

Tony

Re: [PATCH 2/2] ARM: OMAP4: MMC: no regulator off during probe for eMMC

[Kishore Kadiyala]

On Mon, May 30, 2011 at 7:55 PM, Balaji T K <balajitk@ti.com> wrote:
> eMMC does not handle power off when not in sleep state,
> Skip regulator disable during probe when eMMC is
> not in known state - state left by bootloader.
>
> Resolves eMMC failure on OMAP4
> mmc0: error -110 whilst initialising MMC card
>
> Signed-off-by: Balaji T K <balajitk@ti.com>

Tested-by:  Kishore Kadiyala <kishore.kadiyala@ti.com>
Acked-by:  Kishore Kadiyala <kishore.kadiyala@ti.com>

> ---
>  arch/arm/mach-omap2/board-4430sdp.c   |    1 +
>  arch/arm/mach-omap2/hsmmc.c           |    3 +++
>  arch/arm/mach-omap2/hsmmc.h           |    1 +
>  arch/arm/plat-omap/include/plat/mmc.h |    3 +++
>  drivers/mmc/host/omap_hsmmc.c         |    3 +++
>  5 files changed, 11 insertions(+), 0 deletions(-)
>
> diff --git a/arch/arm/mach-omap2/board-4430sdp.c b/arch/arm/mach-omap2/board-4430sdp.c
> index 73fa90b..b324605 100644
> --- a/arch/arm/mach-omap2/board-4430sdp.c
> +++ b/arch/arm/mach-omap2/board-4430sdp.c
> @@ -322,6 +322,7 @@ static struct omap2_hsmmc_info mmc[] = {
>                .gpio_wp        = -EINVAL,
>                .nonremovable   = true,
>                .ocr_mask       = MMC_VDD_29_30,
> +               .no_off_init    = true,
>        },
>        {
>                .mmc            = 1,
> diff --git a/arch/arm/mach-omap2/hsmmc.c b/arch/arm/mach-omap2/hsmmc.c
> index 3f8dc16..28ca144 100644
> --- a/arch/arm/mach-omap2/hsmmc.c
> +++ b/arch/arm/mach-omap2/hsmmc.c
> @@ -338,6 +338,9 @@ static int __init omap_hsmmc_pdata_init(struct omap2_hsmmc_info *c,
>        if (c->no_off)
>                mmc->slots[0].no_off = 1;
>
> +       if (c->no_off_init)
> +               mmc->slots[0].no_regulator_off_init = c->no_off_init;
> +
>        if (c->vcc_aux_disable_is_sleep)
>                mmc->slots[0].vcc_aux_disable_is_sleep = 1;
>
> diff --git a/arch/arm/mach-omap2/hsmmc.h b/arch/arm/mach-omap2/hsmmc.h
> index f119348..f757e78 100644
> --- a/arch/arm/mach-omap2/hsmmc.h
> +++ b/arch/arm/mach-omap2/hsmmc.h
> @@ -18,6 +18,7 @@ struct omap2_hsmmc_info {
>        bool    nonremovable;   /* Nonremovable e.g. eMMC */
>        bool    power_saving;   /* Try to sleep or power off when possible */
>        bool    no_off;         /* power_saving and power is not to go off */
> +       bool    no_off_init;    /* no power off when not in MMC sleep state */
>        bool    vcc_aux_disable_is_sleep; /* Regulator off remapped to sleep */
>        int     gpio_cd;        /* or -EINVAL */
>        int     gpio_wp;        /* or -EINVAL */
> diff --git a/arch/arm/plat-omap/include/plat/mmc.h b/arch/arm/plat-omap/include/plat/mmc.h
> index f38fef9..c7b8741 100644
> --- a/arch/arm/plat-omap/include/plat/mmc.h
> +++ b/arch/arm/plat-omap/include/plat/mmc.h
> @@ -101,6 +101,9 @@ struct omap_mmc_platform_data {
>                /* If using power_saving and the MMC power is not to go off */
>                unsigned no_off:1;
>
> +               /* eMMC does not handle power off when not in sleep state */
> +               unsigned no_regulator_off_init:1;
> +
>                /* Regulator off remapped to sleep */
>                unsigned vcc_aux_disable_is_sleep:1;
>
> diff --git a/drivers/mmc/host/omap_hsmmc.c b/drivers/mmc/host/omap_hsmmc.c
> index 259ece0..5b2e215 100644
> --- a/drivers/mmc/host/omap_hsmmc.c
> +++ b/drivers/mmc/host/omap_hsmmc.c
> @@ -435,6 +435,9 @@ static int omap_hsmmc_reg_get(struct omap_hsmmc_host *host)
>                reg = regulator_get(host->dev, "vmmc_aux");
>                host->vcc_aux = IS_ERR(reg) ? NULL : reg;
>
> +               /* For eMMC do not power off when not in sleep state */
> +               if (mmc_slot(host).no_regulator_off_init)
> +                       return 0;
>                /*
>                * UGLY HACK:  workaround regulator framework bugs.
>                * When the bootloader leaves a supply active, it's
> --
> 1.7.0.4
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html
>

[PATCH 2/2] ARM: OMAP4: MMC: no regulator off during probe for eMMC

[Kishore Kadiyala]

On Mon, May 30, 2011 at 7:55 PM, Balaji T K <balajitk@ti.com> wrote:
> eMMC does not handle power off when not in sleep state,
> Skip regulator disable during probe when eMMC is
> not in known state - state left by bootloader.
>
> Resolves eMMC failure on OMAP4
> mmc0: error -110 whilst initialising MMC card
>
> Signed-off-by: Balaji T K <balajitk@ti.com>

Tested-by:  Kishore Kadiyala <kishore.kadiyala@ti.com>
Acked-by:  Kishore Kadiyala <kishore.kadiyala@ti.com>

> ---
> ?arch/arm/mach-omap2/board-4430sdp.c ? | ? ?1 +
> ?arch/arm/mach-omap2/hsmmc.c ? ? ? ? ? | ? ?3 +++
> ?arch/arm/mach-omap2/hsmmc.h ? ? ? ? ? | ? ?1 +
> ?arch/arm/plat-omap/include/plat/mmc.h | ? ?3 +++
> ?drivers/mmc/host/omap_hsmmc.c ? ? ? ? | ? ?3 +++
> ?5 files changed, 11 insertions(+), 0 deletions(-)
>
> diff --git a/arch/arm/mach-omap2/board-4430sdp.c b/arch/arm/mach-omap2/board-4430sdp.c
> index 73fa90b..b324605 100644
> --- a/arch/arm/mach-omap2/board-4430sdp.c
> +++ b/arch/arm/mach-omap2/board-4430sdp.c
> @@ -322,6 +322,7 @@ static struct omap2_hsmmc_info mmc[] = {
> ? ? ? ? ? ? ? ?.gpio_wp ? ? ? ?= -EINVAL,
> ? ? ? ? ? ? ? ?.nonremovable ? = true,
> ? ? ? ? ? ? ? ?.ocr_mask ? ? ? = MMC_VDD_29_30,
> + ? ? ? ? ? ? ? .no_off_init ? ?= true,
> ? ? ? ?},
> ? ? ? ?{
> ? ? ? ? ? ? ? ?.mmc ? ? ? ? ? ?= 1,
> diff --git a/arch/arm/mach-omap2/hsmmc.c b/arch/arm/mach-omap2/hsmmc.c
> index 3f8dc16..28ca144 100644
> --- a/arch/arm/mach-omap2/hsmmc.c
> +++ b/arch/arm/mach-omap2/hsmmc.c
> @@ -338,6 +338,9 @@ static int __init omap_hsmmc_pdata_init(struct omap2_hsmmc_info *c,
> ? ? ? ?if (c->no_off)
> ? ? ? ? ? ? ? ?mmc->slots[0].no_off = 1;
>
> + ? ? ? if (c->no_off_init)
> + ? ? ? ? ? ? ? mmc->slots[0].no_regulator_off_init = c->no_off_init;
> +
> ? ? ? ?if (c->vcc_aux_disable_is_sleep)
> ? ? ? ? ? ? ? ?mmc->slots[0].vcc_aux_disable_is_sleep = 1;
>
> diff --git a/arch/arm/mach-omap2/hsmmc.h b/arch/arm/mach-omap2/hsmmc.h
> index f119348..f757e78 100644
> --- a/arch/arm/mach-omap2/hsmmc.h
> +++ b/arch/arm/mach-omap2/hsmmc.h
> @@ -18,6 +18,7 @@ struct omap2_hsmmc_info {
> ? ? ? ?bool ? ?nonremovable; ? /* Nonremovable e.g. eMMC */
> ? ? ? ?bool ? ?power_saving; ? /* Try to sleep or power off when possible */
> ? ? ? ?bool ? ?no_off; ? ? ? ? /* power_saving and power is not to go off */
> + ? ? ? bool ? ?no_off_init; ? ?/* no power off when not in MMC sleep state */
> ? ? ? ?bool ? ?vcc_aux_disable_is_sleep; /* Regulator off remapped to sleep */
> ? ? ? ?int ? ? gpio_cd; ? ? ? ?/* or -EINVAL */
> ? ? ? ?int ? ? gpio_wp; ? ? ? ?/* or -EINVAL */
> diff --git a/arch/arm/plat-omap/include/plat/mmc.h b/arch/arm/plat-omap/include/plat/mmc.h
> index f38fef9..c7b8741 100644
> --- a/arch/arm/plat-omap/include/plat/mmc.h
> +++ b/arch/arm/plat-omap/include/plat/mmc.h
> @@ -101,6 +101,9 @@ struct omap_mmc_platform_data {
> ? ? ? ? ? ? ? ?/* If using power_saving and the MMC power is not to go off */
> ? ? ? ? ? ? ? ?unsigned no_off:1;
>
> + ? ? ? ? ? ? ? /* eMMC does not handle power off when not in sleep state */
> + ? ? ? ? ? ? ? unsigned no_regulator_off_init:1;
> +
> ? ? ? ? ? ? ? ?/* Regulator off remapped to sleep */
> ? ? ? ? ? ? ? ?unsigned vcc_aux_disable_is_sleep:1;
>
> diff --git a/drivers/mmc/host/omap_hsmmc.c b/drivers/mmc/host/omap_hsmmc.c
> index 259ece0..5b2e215 100644
> --- a/drivers/mmc/host/omap_hsmmc.c
> +++ b/drivers/mmc/host/omap_hsmmc.c
> @@ -435,6 +435,9 @@ static int omap_hsmmc_reg_get(struct omap_hsmmc_host *host)
> ? ? ? ? ? ? ? ?reg = regulator_get(host->dev, "vmmc_aux");
> ? ? ? ? ? ? ? ?host->vcc_aux = IS_ERR(reg) ? NULL : reg;
>
> + ? ? ? ? ? ? ? /* For eMMC do not power off when not in sleep state */
> + ? ? ? ? ? ? ? if (mmc_slot(host).no_regulator_off_init)
> + ? ? ? ? ? ? ? ? ? ? ? return 0;
> ? ? ? ? ? ? ? ?/*
> ? ? ? ? ? ? ? ?* UGLY HACK: ?workaround regulator framework bugs.
> ? ? ? ? ? ? ? ?* When the bootloader leaves a supply active, it's
> --
> 1.7.0.4
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
> the body of a message to majordomo at vger.kernel.org
> More majordomo info at ?http://vger.kernel.org/majordomo-info.html
>