From: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
To: Sander Eikelenboom <linux@eikelenboom.it>
Cc: xen-devel <xen-devel@lists.xensource.com>
Subject: Re: Warn/panics booting Konrad's master tree under xen 4.1.1
Date: Mon, 25 Jul 2011 10:44:38 -0400 [thread overview]
Message-ID: <20110725144438.GA29876@dumpdata.com> (raw)
In-Reply-To: <56664053.20110723214010@eikelenboom.it>
On Sat, Jul 23, 2011 at 09:40:10PM +0200, Sander Eikelenboom wrote:
> Hi Konrad,
Hey Sander,
>
> I have tried your current master tree (commit 602d7a606974c54dc8bd61527c051d7d697a5f86) as domU (under xen 4.1.1 and a 2.6.32.35 dom0), that seems to work fine.
>
Great..
> I have tried to use the same kernel as dom0 as well, but i get the warns/panic below, when i boot the kernel bare metal it works ok.
OK, so only as Dom0 you get this.
> Complete serial log is attached, i have re-compiled with and without pv-spinlocks but there is no difference.
>
> Also xen-pciback compiled in, with xen-pciback.hide as kernel boot parameter doesn't seem to seize the devices.
Can you attach the .config file please? And the lspci/lsusb for your Pinnacle capture thingy.
You have been doing the USB passthrough for some time right - is this a new piece of hardware
or was it the one you used for some time?
> [ 5.139589] Call Trace:
> [ 5.139592] [<ffffffff811006c8>] unmap_vmas+0x468/0x9f0
> [ 5.139596] [<ffffffff81103a84>] exit_mmap+0xa4/0x150
> [ 5.139600] [<ffffffff81007fa0>] ? xen_clocksource_read+0x20/0x30
> [ 5.139603] [<ffffffff8104f41f>] mmput+0x4f/0xe0
> [ 5.139607] [<ffffffff81053e01>] exit_mm+0x131/0x170
> [ 5.139610] [<ffffffff81055c04>] do_exit+0x174/0x860
> [ 5.139613] [<ffffffff81765eb0>] ? _raw_spin_unlock_irqrestore+0x40/0x80
> [ 5.139617] [<ffffffff81051dda>] ? kmsg_dump+0x4a/0x100
> [ 5.139620] [<ffffffff810080f2>] ? check_events+0x12/0x20
> [ 5.139623] [<ffffffff8100f62d>] oops_end+0x9d/0xd0
> [ 5.139627] [<ffffffff8103323b>] no_context+0xfb/0x260
> [ 5.139630] [<ffffffff81004651>] ? pte_mfn_to_pfn+0x91/0xf0
> [ 5.139633] [<ffffffff810334c5>] __bad_area_nosemaphore+0x125/0x1f0
> [ 5.139638] [<ffffffff81004169>] ? __raw_callee_save_xen_pmd_val+0x11/0x1e
> [ 5.139641] [<ffffffff810335a3>] bad_area_nosemaphore+0x13/0x20
> [ 5.139644] [<ffffffff81033ad5>] do_page_fault+0x2f5/0x490
> [ 5.139648] [<ffffffff810080df>] ? xen_restore_fl_direct_reloc+0x4/0x4
> [ 5.139652] [<ffffffff810e2173>] ? __alloc_pages_nodemask+0x113/0x720
> [ 5.139657] [<ffffffff8133e1aa>] ? trace_hardirqs_off_thunk+0x3a/0x6c
> [ 5.139663] [<ffffffff817665c5>] page_fault+0x25/0x30
> [ 5.139666] [<ffffffff8110016e>] ? __tlb_remove_page+0x9e/0xc0
> [ 5.139670] [<ffffffff81100164>] ? __tlb_remove_page+0x94/0xc0
> [ 5.139673] [<ffffffff8110086d>] unmap_vmas+0x60d/0x9f0
> [ 5.139677] [<ffffffff81103a84>] exit_mmap+0xa4/0x150
> [ 5.139680] [<ffffffff8104f41f>] mmput+0x4f/0xe0
> [ 5.139683] [<ffffffff811271b6>] flush_old_exec+0x556/0x800
> [ 5.139686] [<ffffffff8116f4a3>] load_elf_binary+0x323/0x1c60
.. snip.. Hm, that is definitly bad.
> [ 6.455861] udlfb: Reallocating framebuffer. Addresses will change!
> [ 6.531120] ------------[ cut here ]------------
> [ 6.532810] WARNING: at lib/dma-debug.c:875 check_for_stack+0xad/0xf0()
> [ 6.532810] Hardware name: MS-7640
> [ 6.532810] ehci_hcd 0000:07:01.2: DMA-API: device driver maps memory fromstack [addr=ffff880023321960]
Ah, that one reminds of the USB floppy bug. Not a big problem but annoying.
> [ 6.532810] Modules linked in:
> [ 6.532810] Pid: 563, comm: khubd Tainted: G D 3.0.0-xen-3.1-konrad-master-20110722+ #1
> [ 6.532810] Call Trace:
> [ 6.532810] [<ffffffff8105180f>] warn_slowpath_common+0x7f/0xc0
> [ 6.532810] [<ffffffff81051906>] warn_slowpath_fmt+0x46/0x50
> [ 6.532810] [<ffffffff813517dd>] check_for_stack+0xad/0xf0
> [ 6.532810] [<ffffffff81353389>] debug_dma_map_page+0x179/0x1e0
> [ 6.532810] [<ffffffff814e9a0c>] usb_hcd_map_urb_for_dma+0x5ec/0x6a0
> [ 6.532810] [<ffffffff814e9c6e>] usb_hcd_submit_urb+0x14e/0x780
> [ 6.532810] [<ffffffff8110d360>] ? __vmalloc_node_range+0x140/0x1e0
> [ 6.532810] [<ffffffff813a5e02>] ? dlfb_setup_modes+0x512/0x580
> [ 6.532810] [<ffffffff814eb365>] usb_submit_urb+0xe5/0x2b0
> [ 6.532810] [<ffffffff814ecae3>] usb_start_wait_urb+0x63/0x100
> [ 6.532810] [<ffffffff814eba18>] ? usb_init_urb+0x28/0x40
> [ 6.532810] [<ffffffff814ecdc8>] usb_control_msg+0xe8/0x120
> [ 6.532810] [<ffffffff813a7b11>] dlfb_usb_probe+0x441/0x850
> [ 6.532810] [<ffffffff81765ed9>] ? _raw_spin_unlock_irqrestore+0x69/0x80
> [ 6.532810] [<ffffffff814eee66>] usb_probe_interface+0x106/0x1c0
> [ 6.532810] [<ffffffff81426256>] driver_probe_device+0x96/0x1c0
> [ 6.532810] [<ffffffff81426420>] ? __driver_attach+0xa0/0xa0
> [ 6.532810] [<ffffffff81426473>] __device_attach+0x53/0x60
> [ 6.532810] [<ffffffff81425538>] bus_for_each_drv+0x68/0x90
> [ 6.532810] [<ffffffff81426557>] device_attach+0xa7/0xc0
> [ 6.532810] [<ffffffff8142530d>] bus_probe_device+0x2d/0x50
> [ 6.532810] [<ffffffff81423f19>] device_add+0x5f9/0x6d0
> [ 6.532810] [<ffffffff814edd4e>] usb_set_configuration+0x45e/0x690
> [ 6.532810] [<ffffffff811917ea>] ? sysfs_do_create_link+0xfa/0x220
> [ 6.532810] [<ffffffff814f6914>] generic_probe+0x44/0xa0
> [ 6.532810] [<ffffffff814ee1da>] usb_probe_device+0x1a/0x20
> [ 6.532810] [<ffffffff81426256>] driver_probe_device+0x96/0x1c0
> [ 6.532810] [<ffffffff81426420>] ? __driver_attach+0xa0/0xa0
> [ 6.532810] [<ffffffff81426473>] __device_attach+0x53/0x60
> [ 6.532810] [<ffffffff81425538>] bus_for_each_drv+0x68/0x90
> [ 6.532810] [<ffffffff81426557>] device_attach+0xa7/0xc0
> [ 6.532810] [<ffffffff8142530d>] bus_probe_device+0x2d/0x50
> [ 6.532810] [<ffffffff81423f19>] device_add+0x5f9/0x6d0
> [ 6.532810] [<ffffffff814ed8d9>] ? usb_cache_string+0x99/0xb0
> [ 6.532810] [<ffffffff814e5a27>] usb_new_device+0x167/0x1f0
> [ 6.532810] [<ffffffff814e72f8>] hub_thread+0xba8/0x1330
> [ 6.532810] [<ffffffff8176331f>] ? schedule+0x42f/0xa70
> [ 6.532810] [<ffffffff81074e20>] ? wake_up_bit+0x40/0x40
> [ 6.532810] [<ffffffff81765ed9>] ? _raw_spin_unlock_irqrestore+0x69/0x80
> [ 6.532810] [<ffffffff814e6750>] ? hub_probe+0x850/0x850
> [ 6.532810] [<ffffffff814e6750>] ? hub_probe+0x850/0x850
> [ 6.532810] [<ffffffff810748d6>] kthread+0x96/0xa0
> [ 6.532810] [<ffffffff81767a64>] kernel_thread_helper+0x4/0x10
> [ 6.532810] [<ffffffff81766341>] ? retint_restore_args+0x13/0x13
> [ 6.532810] [<ffffffff81767a60>] ? gs_change+0x13/0x13
> [ 6.532810] ---[ end trace 09caa95ef959351a ]---
>
>
>
>
> [ 29.224385] em28xx #0: Identified as Pinnacle PCTV USB 2 (card=3)
> [ 29.233168] BUG: unable to handle kernel paging request at ffff880020221000
> [ 29.236056] IP: [<ffffffff8110016e>] __tlb_remove_page+0x9e/0xc0
And this is even worst..
> [ 29.244097] PGD 1a4e067 PUD 1a52067 PMD 2ff67067 PTE 8010000020221064
> [ 29.244097] Oops: 0002 [#3] SMP DEBUG_PAGEALLOC
> [ 29.256140] CPU 5
> [ 29.256140] Modules linked in:
> [ 29.256140]
> [ 29.256140] Pid: 1785, comm: modprobe Tainted: G D W 3.0.0-xen-3.1-konrad-master-20110722+ #1 MSI MS-7640/890F
> XA-GD70 (MS-7640)
> [ 29.256140] RIP: e030:[<ffffffff8110016e>] [<ffffffff8110016e>] __tlb_remove_page+0x9e/0xc0
> [ 29.256140] RSP: e02b:ffff88002024fc38 EFLAGS: 00010286
> [ 29.256140] RAX: 0000000000000000 RBX: ffff88002024fd98 RCX: ffff880020221000
> [ 29.256140] RDX: ffff880020221000 RSI: ffff88002f0f8000 RDI: 0000000000000000
> [ 29.256140] RBP: ffff88002024fc48 R08: 00003ffffffff000 R09: ffff880000000000
> [ 29.256140] R10: 0000000000000000 R11: ffffffff81af32d0 R12: 0000000000407000
> [ 29.256140] R13: ffff88002876c3c8 R14: ffff88002024fd48 R15: ffff8800200c4680
> [ 29.256140] FS: 00007f3469119700(0000) GS:ffff88002f0a8000(0000) knlGS:0000000000000000
> [ 29.256140] CS: e033 DS: 0000 ES: 0000 CR0: 000000008005003b
> [ 29.256140] CR2: ffff880020221000 CR3: 0000000001a4d000 CR4: 0000000000000660
> [ 29.256140] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
> [ 29.256140] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
> [ 29.256140] Process modprobe (pid: 1785, threadinfo ffff88002024e000, task ffff880023318000)
> [ 29.256140] Stack:
> [ 29.256140] 0000000000000006 ffff8800201c7038 ffff88002024fd88 ffffffff8110086d
> [ 29.256140] ffffffff810080f2 0000000000000246 0000000000000000 0000000000000000
> [ 29.256140] ffffffff81afcce8 ffff88002024fe00 0000000000000000 ffff8800200c4680
> [ 29.256140] Call Trace:
> [ 29.256140] [<ffffffff8110086d>] unmap_vmas+0x60d/0x9f0
> [ 29.256140] [<ffffffff810080f2>] ? check_events+0x12/0x20
> [ 29.256140] [<ffffffff81103a84>] exit_mmap+0xa4/0x150
> [ 29.256140] [<ffffffff8104f41f>] mmput+0x4f/0xe0
> [ 29.256140] [<ffffffff81053e01>] exit_mm+0x131/0x170
> [ 29.256140] [<ffffffff81055c04>] do_exit+0x174/0x860
> [ 29.256140] [<ffffffff8111ba30>] ? kmem_cache_free+0x20/0x130
> [ 29.256140] [<ffffffff81056345>] do_group_exit+0x55/0xf0
> [ 29.256140] [<ffffffff810563f7>] sys_exit_group+0x17/0x20
> [ 29.256140] [<ffffffff81766c42>] system_call_fastpath+0x16/0x1b
> [ 29.256140] Code: e8 68 f2 00 00 48 83 c4 08 b8 01 00 00 00 5b c9 c3 0f 1f 40 00 31 f6 bf 00 02 00 00 e8 cc 26 fe ff
> 48 89 c1 31 c0 48 85 c9 74 a2
> [ 29.256140] c7 01 00 00 00 00 c7 41 08 00 00 00 00 c7 41 0c fe 01 00 00
> [ 29.256140] RIP [<ffffffff8110016e>] __tlb_remove_page+0x9e/0xc0
> [ 29.256140] RSP <ffff88002024fc38>
> [ 29.256140] CR2: ffff880020221000
> [ 29.256140] ---[ end trace 09caa95ef959351b ]---
> [ 29.256140] Fixing recursive fault but reboot is needed!
>
> \ // _ \ '_ \ || |_ | | | |
> \ __/ | | | | _|| |_| |
> /\_\___|_| |_| _|(_)_(_)_|
>
> (XENXen version 4.1.(root@dyndns.org(gcc version 4.4 (Debian 4.4.5-8) Thu Jun 16 11::46 CEST 2011
> (N) Latest Changet: Tue Jun 14 142:48 2011 +0100 079:73a8061b01f1(XEN) BootloaderGRUB 1.98+201008-14
> (XEN) Comma line: dom0_mem=8M loglvl=all lovl_guest=all conle_timestamps vga=gfx-1280x1024x3cpuidle cpufreq=n noreboot d
> ebugapic=debug apic_rbosity=debug ap=debug acpi_enfoe_resources=lax mmu=on,amd-iommuebug amd_iommu=oamd-iommu-debug m1=1
> 15200,8n1 coole=vga,com1
<blinks>
dom0_mem=8M? Ah looks like your serial console is being eaten up. N/m then.
next prev parent reply other threads:[~2011-07-25 14:44 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2011-07-23 19:40 Warn/panics booting Konrad's master tree under xen 4.1.1 Sander Eikelenboom
2011-07-25 14:44 ` Konrad Rzeszutek Wilk [this message]
2011-07-25 15:04 ` Sander Eikelenboom
2011-07-26 21:03 ` Konrad Rzeszutek Wilk
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20110725144438.GA29876@dumpdata.com \
--to=konrad.wilk@oracle.com \
--cc=linux@eikelenboom.it \
--cc=xen-devel@lists.xensource.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.